Whirlpool EV209NBT - INSTALLATION 5-10 Owner`s manual
Contents
1. Chromotherapy Mood Light The ColorGlo LED Multi Color bath light comes pre programmed with 10 light modes To change modes switch the unit off and then back on within 5 seconds To resume a lighting mode leave the unit switched off to save the last lighting mode displayed in memory That same lighting mode will display the next time the unit is switched on DO NOT attempt to service the electronic components yourself Any opening altering or tampering with this product will void the manufacturer s warranty DO NOT submerge the transformer in water or allow it to get wet Keep the unit dry at all times DO NOT allow this unit to freeze Ozonator This factory installed option sanitizes your whirlpool When your whirlpool system is operating your ozonator is generating ozone which is mixed with the re circulating bath water The ozone helps neutralize soaps body oils and other organic and inorganic materials This unit eliminates the need to run a sanitation solution through the tub s circulating system Aromatherapy This option uses your favorite pure essential oils and their fragrances to treat your mind and body A few drops added to a felt pad in the aromatherapy canister provides the scent to relax and achieve your desired mood Place the cap on the canister and operate your air massage system The scent is drawn into the air system and blown through the air injectors Solo Touch Control The Solo Touch system operation and installation inform2. Massage Pillow Back Massage Jets Can be ordered separately ee A uc cu Back Massage Functioning Includes 8 jets that function on an independent 3 4 hp 7 5Amps 2 jets work at a time cycling up and down your back This system requires a 20Amp dedicated circuit 120V Back Massage Controls DO NOT OPERATE the back massage system before you are in the tub and ready for use Doing so will spray water out of your tub 1 The push button located at the bottom left of the photo above turns the unit on and off The dial 2 on the left is the Air Control for the back massage system Adjusting this will increase and decrease the intensity of the jets The large dial 3 on the right will adjust the cycling speed of the jets from completely stopped on 2 active jets to quickly cycling up and down through the entire back massage system Neck Massage Controls DO NOT OPERATE the neck massage before you are in the tub and ready for use Doing so will spray water out of your tub The middle button 4 is the On Off button Pushing the button on the left will adjust the speed of the neck massage jets and set them to pulse simultaneously Press once for fast twice for medium and three times for low speed The button on the right performs the same function only with the jets alternating back and forth Once activated the neck massage will run on a 20 min timer Page 7 LMW Colony Collection Owner s Manual
3. minutes before further use Verify that the main air hose from the manifold to the blower is properly connected If necessary reconnect and tighten clamps If the air outlets of a jet head are obstructed by soap or other residues fill the tub with warm water then switch the system on and off several times The air outlets should be cleared if this is not sufficient carefully tap on the jet heads with the handle of a screw driver or similar tool while the blower runs Fill the tub to working level amp operate blower on high for 5 minutes Carefully feel the flexible connection hose where it connects to blower The hose and its immediate area should feel warm to the touch if not call Laurel Mountain Whirlpools If your tub is installed against 2 outside walls adequate insulation is recommended to minimize heat loss
4. button again changes to Pulse Mode In Pulse Mode the blower will release air in short intense bursts Pressing the button again will return the blower to normal Standard Drying Cycle An automatic drying cycle will start 20 minutes after the blower is turned off The blower LED blinks while waiting for the purge cycle 24 Hour Programmable Drying Cycle The system must be stopped prior to activation or deactivation Activation Determine at which time you wish the purge to activate At that precise time press and hold Button 2 on the keypad for 5 seconds All of the LED lights will flash twice to confirm the activation is complete The purge cycle will now start at the programmed time every 24 hrs In the event of a power failure the program will be automatically deactivated Deactivion Press and hold Button 2 for 5 seconds All of the buttons will flash once to confirm deactivation Functioning 1 16 lateral turbo air injectors spaced around the lower side walls of the tub 2 The system functions with a 2 hp blower 600W air heater that is separate from any other systems 3 This system requires a 20Amp dedicated circuit 120V 4 The air heater is designed to provide a warm air massage It is not designed to heat the bath water Page 6 LMW Colony Collection Owner s Manual Options amp Features Whirlpool Inline Heater The inline heater is designed to MAINTAIN the temperature of the bath water between 101 104 degr
5. in material and workmanship for the following periods The bathtub shell carries a limited lifetime warranty The pump blower and heater have a limited 10 year warranty All other parts have a limited 5 year warranty Proof of purchase is required This warranty is issued to the original purchaser and shall be effective from the date of purchase as shown on purchaser s receipt Laurel Mountain Whirlpools will repair or replace at their choice any unit which proves to be defective in material or workmanship under normal use and service having been properly installed This warranty is the only express warranty made by Laurel Mountain Whirlpools and is limited to the duration of this warranty Any labor charges and or damage incurred in installation repair or replacement as well as incidental and consequential damages connected therewith are excluded and will not be paid by Laurel Mountain Whirlpools Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty is void for any damage to the bath due to abuse misuse neglect accident improper installation any use violating instructions furnished by us or repair not authorized in writing by Laurel Mountain PROBLEM SOLUTION PROBLEM SOLUTION ON OFF BUTTON Won t depress PUMP Won t Start Motor hums LEAKS Pump Unions Pump o ring or seal Pipe to Jet JET Low no water pre
6. LAUREL MOUNTAIN WHIRLPOOLS COLONY COLLECTION OWNER S MANUAL For your installation operation and maintenance needs Whirlpools Air Baths Combo Baths Soakers i i cO s naYpe ix QE UE S y uu WATER TEST PRIOR TO INSTALLATION Laurel Mountain Whirlpools Service Center 1 800 930 0050 V9 14 Specifications Care amp Cleaning Rough In Instructions Whirlpool Operation Electrical Wiring Air Bath Operation Plumbing Instructions Extra Options Features Operating Instructions Warranty amp Troubleshooting About this Owner s Manual Laurel Mountain Whirlpools has gained popularity by the variety of bathtubs available and the extensive list of options for each type of tub This manual covers the installation operation and maintenance needs for all of the Colony Series Laurel Mountain whirlpools air baths combo baths and soaker tubs If you have any questions or need additional information on your Laurel Mountain Whirlpools bath you can contact our customer service department Mon Fri at 1 800 930 0050 between 6 00 am and 6 00 pm EST INSTALLATION WARNING Your Laurel Mountain Whirlpools bathtub has been water tested prior to shipment However due to transportation and potential on the job conditions you should NOT install this tub until making a final water test Building material amp wiring should be routed away from the pump or other heat producing parts o
7. anel gt battom of panel amp slide panel up to style line This Diagram A Diagram B will disengage the bottom of spring clip Pull Equal Distance Spring I piss Bad All Around Clips bottom forward then down to disengage top amp Removable remove panel Panel To install Reverse above after centering panel in Hace ere cce operning leftto right move panel into position using the palm of your hand DO NOT USE TOOLS ON SURFACE Diagram C Page 3 LMW Colony Collection Owner s Manual Electrical amp Wiring instructions Rough in the wiring on a single 120VAC 20 amp GFCI protected dedicated circuit for each accessory installed on the tub WARNINGS 1 All electrical connections must be made by a licensed certified electrician in accordance with the requirements of the National Electrical Code and applicable state and local codes and procedures 2 All circuits connected to this unit must be equipped with Ground Fault Circuit Interrupter GFCI protection It is the tub installer s responsibility to wire the circuit with GFCI 3 All bathtubs equipped with an inline heater require two dedicated circuits One for the whirlpool system and one for optional inline heater 4 DO NOT splice a longer cord to the power supply cord and DO NOT connect to an extension cord All whirlpool air systems and heaters are equipped with a molded plug on the end of a power supply core Install a separate dedicate
8. ation is shown below INSTALLATION KEYPAD OPERATION 1 0068 OO TEMPERATURE SENSOR Hna f TEMPERATURE SENSOR CONNECTOR Screen off on Displays temperature speed time LIGHT 1A MAX VSC CONTROLLER bel remaining or error info i PROBES e nis Displays temperature value in degrees Fahrenheit RJ 25 in IF M IL MM JUMPER CABLE opeed level Displays speed level from 1 to 10 oman Displays the time remaining in minutes 1st press activates pump light and LED en 2nd press deactivates pump light and LED Speed Speed increases by 1 level display will show utn current speed Speed decreases by 1 level display will show current speed VHITE AL Kou moda 1st press activates pulse mode amp LED CERIS Teo 2nd press deactivates pulse mode amp LED Aes 4 Liaht button 1st press activates Light mode amp LED V REEN G j 2nd press deactivates light mode amp LED ATTI Features Pulsating Mode The pump speed varies automatically with a cycle period of approximately 10 seconds Speed 10 is the default speed but the keypad will remember the last speed used after being shut down and will automatically revert to that speed Wait 5 seconds after powering on the unit to adjust the speed settings Pages LMW Colony Collection Owner s Manual Laurel Mountain Whirlpools Warranty This Laurel Mountain Whirlpools bath is warranted to the original purchaser to be free from defects
9. ator was purchased ALL TUBS Your bath has an acrylic finish and will retain its high luster for years with proper care Never use an abrasive cleaner or pad to clean your bath tub Always use a soft cloth or sponge along with a spray liquid non abrasive bath cleaner disinfectant On the metallic finish use only a soft cloth and warm soapy water Page 5 LMW Colony Collection Owner s Manual Whiripooi Operation If your bath has a whirlpool system simply pushing the push button located on the tub will turn the tub on or off The button next to it will cycle through the various speeds of the pump low medium and high Individual jets may be adjusted by turning the jet ring trim clockwise and the water flow will increase while turning the jet trim counterclockwise will decrease the water flow The jets can be closed if turned far enough counterclockwise The 8 jet system has a 2 hp pump and requires a 20 amp dedicated circuit 120V Air Bath Operation The air bath is operated by touching the control pad pictured below 1 2 3 4 1 ON OFF Press to start press again to stop 2 INCREASE SPEED Press and hold to increase the speed of air flow Release when desired speed is reached 3 DECREASE SPEED Press and hold to decrease the speed of air flow Release when desired speed is reached 4 PULSE CYCLES Pressing this button once will turn on Wave Mode which fluctuates the blower from minimum to maximum power Pressing the
10. d 120VAC 20 Amp GFCI protected electrical wall plug outlet inside the access panel for each accessory equipped on the tub For example if the tub is equipped with a whirlpool system only then one GFCI wall plug outlet is necessary If the tub is equipped with both whirlpool system and a heater then two separate circuits with GFCI wall plug outlets are required Be sure to count the number of accessories before installing the GFCI wall outlets Also the power supply cords equipped with each accessory are only 2 5 long so locate the GFCI wall outlet within 1 5 of the intended accessory Electrical Requirements 75 hp Pump 120V 7 5 Amps Whirlpool heater 120V 12 0 Amps 2 hp Pump 120V 9 5 Amps Air Soaker heater 120V 12 5 Amps 2 5 hp Pump 120V 13 5 Amps Air Soaker heater 240V 16 0 Amps 2 hp Blower Heater 120V 12 0 Amps Ozonator 120V 1 0 Amps Please note that when sizing the electrical circuits to power the unit you should always check the rating labels on equipment because there could be changes Plumbing Installation Install fill valves and spout in the desired locations Note due to various possible fill valve and spout locations the holes are not drilled at the factory Make certain that the spout is long enough to clear the interior rim of the tub If installing fill valves on the deck of the tub be sure that you have enough clearance for connections of valve to tub and water connections befo
11. ees Fahrenheit These limits cannot be increased or decreased The Heater is operated by a pressure switch which is programmed into the heater This switch allows the heater to operate only when there is sufficient water flowing through the system DO NOT BYPASS THE SWITCH This option is equipped with a molded plug on the end of a supply cord Check your local codes and install a 120VAC 20amp GFCI protected dedicated circuit wall outlet within 1 5 from the heater unit Plug the cord into the outlet Every time the whirlpool unit is activated the heater will activate as well and will MAINTAIN the water s temperature between 101 104 F Water Heater for Air Bath and Soaker Tubs The on off button on the bath tub activates deactivates the heater The heater has a built in 20 minute timer and is a low flow high efficiency pump providing silent operation The option is equipped with a molded plug on the end of a power supply cord Check your local codes For the LM305 install a 120 VAC 15amp GFCI and for the LM306 install a 250 VAC 25amp GFCI Both water heaters should have a GFCI protected dedicated circuit wall outlet located within 1 5 from the heater unit Plug the cord into the outlet This heater is designed to MAINTAIN the temperature in your bath water between 101 104 deg Fahrenheit These temperatures are preset and cannot be adjusted Hydrotherapy Back Massage System amp Neck Massage Pillow Neck Massage Pillow Control Neck
12. er test of your own to ensure all of the fittings and connections were not damaged during transit Take your tub to an area where you can fill it up run electrical components amp drain Page 2 LMW Colony Collection Owner s Manual it Fill your tub to the overflow and if you have a pump and or blower operate it for 15 minutes Inspect the entire unit during and after for leaks Any defects that are discovered MUST be reported at this time to qualify for warranty coverage Qualified plumbers and electricians MUST be used for all tub connections to assure you follow local codes and acquire any permits required for the install NEVER LIFT the unit by any portion of the plumbing or stand in the unit during installation as this may cause serious damage to the unit Framing in Your Bath It is VERY important that your tub is supported by its base and not the rim Take your installation measurements directly from your tub as they may vary slightly from our literature When installing the drain fitting you will notice it protrudes below the bottom of the tub You will need to allow clearance in the sub floor for this dimension Now you are ready to place your tub in its desired location Check the unit and sub floor to ensure it is level If it is not insert wood shims between the sub floor and support base Mark stud wall underneath the tub s return lip Remove the unit from position and install a 1x stop to stud wall for lip to rest on to preve
13. f not DO NOT use the Use this tub if you think or know you are unit as this indicated there is a ground current flowing and that a possibility of ELECTRIC SHOCK Use alcohol drugs or medication This will greatly increase your risk of hypothermia or drowning exists Disconnect the unit at once and call a Allow children to use the bathtub without qualified electrician before further operation adult supervision Operate the whirlpool without the suction Use this tub for its intended purposes described in SAST this manual The manufacturer does not recommend Insert any objects into any of the openings using any attachements not specifically approved in this manual Use options NOT installed by the manufacturer Care amp Cleaning Instructions WHIRLPOOL Prior to using the whirlpool the tub and its system s should be thoroughly cleaned and disinfected DO NOT use abrasive cleaners on the high gloss acrylic finish Use a non abrasive cleaner and rinse thoroughly after cleaning To remove the labels on the tub we recommend using fingernail polish remover if they do not come off easily Fill the tub up with water at least 2 above the highest jet then add 2 tsp of low sudsing automatic dishwashing detergent and no more than 8 oz of household bleach Operate your whirlpool for 5 10 minutes and then drain the tub Refill the tub with water and run the system for another 5 minutes then drain Repeat every 30 days unless an ozon
14. f this tub Please follow these instructions to insure an easy and safe installation process Any deviations additions or deletions to your Laurel Mountain Whirlpools tub or it s hardware will void the warranty of this product if written approval is not obtained from the manufacturer Specifications Your Laurel Mountain Whirlpools unit was created to your order specifications The tub was constructed from an acrylic shell cast It was then reinforced with a mixture of chopped fiberglass in a polyester resin applied to the backside of the shell The base of your unit was designed to give uniform support to the tub floor and has been pre leveled It meets or exceeds load bearing and impact resistance requirements of the listed standard without evidence of crazing or cracking and with minimal deflection when installed in accordance to Laurel Mountain Whirlpools printed instructions PRIOR TO INSTALLATION Immediately inspect your tub upon arrival If any damage has occurred make a notation on the freight carrier s proof of delivery DO NOT remove the bath from its shipping container until you are ready to water test and install When you are prepared to remove the tub from its carton DO NOT LIFT the tub out by its plumbing We also recommend cutting cardboard from the shipping container to place inside the tub to protect its floor Even though your tub has been inspected and water tested prior to shipment it is very important that you perform a wat
15. nt deflection At this time check to see if any wiring needs to be completed see wiring instructions Since a great variety of installations are possible with this bath special framing procedures may be needed A ledge under the rim or an apron without a ledge may be constructed as required Where installation is planned against a wall install the tub against the studs as indicated adding blocking below the rim to prevent deflection or movement of the tub but ensuring that the weight of the tub is not supported in any way by the blocking Diagram A When placing the unit in a platform floor or cut out installation the opening should be 1 smaller than the specified rim dimensions A 1 integral up flange is available on many rectangular and corner models These units should be placed in a pre measured studded pocket Pre drill holes through the flange to align with studs Use screws to secure studs Diagram B DO NOT attempt to nail directly through the flange Always pre drill the holes In every system installation an access panel must be placed near the pump blower for servicing This access may be through the wall or platform apron In the case of a sunken installation access may be through the ceiling below the bathtub See Diagram C for instructions for the access panel provided on the skirted tub Hs ur The panel is held in place with spring clips as Top of Line L shown To remove panel place fingers under ur j tH P
16. re drilling cutting into tub Seal the joints under the tub rim and against the wall with a water resistant seal Then install a standard 1 5 trap to the drain and overflow Before proceeding make a final operational check by filling the tub with water to the overflow and operate for at least 5 minutes Leave the water in the bath for 30 minutes check the connections for leaks during and after operation Complete the installation with desired trim material on the back wall side walls and down exposed interior walls Page 4 LMW Colony Collection Owner s Manual Operation Instructions lt save these important safety instructions gt Laurel Mountain Whirlpools will not be held responsible for water damage of any kind in connection with the installation and or operation of one of our bathtubs All whirlpool jets must be completely submerged below water before starting the pump Do not operate the pump without water as damage may occur Do not block the overflow drain and allow water to reach the controls as they are not waterproof and leaks to the floor may occur important Safety instructions EDT DO NOT Ensure your qualified electrician supplies a Ground Fault Circuit Interrupter GFCI during installation bathtub This offers necessary protection to your unit and should be tested periodically To test simply push the lt TEST BUTTON gt and power should be interrupted Then push the RESET BUTTON and power should be restored I
17. ssure WHIRLPOOL Remove trim ring and plunger Clean interior lubricate with small amount of vasoline Check to see if on off switch or pneumatic switch is ON Check electric power supply Reset the circuit breaker or replace fuse if necessary Check ground fault circuit interrupter Reset if tripped Check to see if both ends of plastic air switch tubes are connected Check for binding of motor shaft or obstruction in pump Manually rotate motor shaft to see that shaft turns freely Check to see if highest jet is clogged Check to see that water is at a high enough level for pump to prime Check for air leak in suction line Slightly loosen pump union amp then retighten by hand Check for obstruction in piping system Loosen pump unions and inspect o ring for proper sealing Retighten Call Laurel Mountain Whirlpools customer service at 1 800 930 0050 Turn the trim ring around the jet This will open close the jet BLOWER Fails to operate MOTOR Runs but no air blown through jets JET HEAD AIR OUTLETS Are obstructed AIR HEATER Does not appear to be working AIR BATH Check electric power supply Reset the circuit breaker or replace fuse if necessary Check ground fault circuit interrupter Reset if tripped If the system has been functioning for an extended period of time it is possible that the thermic protection has shut off the motor Allow to cool off for at least 30
Download Pdf Manuals
Related Search