VS 14 / VS 18
Contents
1. Drive belt Electronic control PC board Support lever Return spring Screw F 3 9 x 13 DIN 7981 Screw C 3 9x 16 DIN 7981 Screw C 3 9 x 22 DIN 7981 Screw AM5 x 30 DIN 7985 A Vacuum Extension Hose 1087 Optinal B VSM Tool Kit Optional 1 Straight Tube 1084 2 Crevice Nozzle 1092 3 Clip 1081 4 Dusting Brush 1094 5 Upholstery Nozzle 1090 6 Wall and Upholstery Brush 1325 C Bags and Filters 1 Paper Bag Pkg of 10 2003 2 Cloth Bag 1079 only use with Micro Filter 3 Exhaust Filter 1534 4 Vac Motor Filter 1044 5 Micro Hospital Filter 1435 A Flexible avec embout 1087 B Accessoires speciaux 1 Tube plastique 1084 2 Buse sifflet 1092 3 Clips de fixation accessoire 1081 4 Brosse poussi re 1094 5 Brosse dure 1080 6 Brosse ovale 1325 C Filtres 1 Sac papier 2003 2 Sac tissus 1079 seulement utiliser avec Micro filtre 3 Filtre de sortie 1534 4 Filtre moteur 1044 5 Micro Filtre 1435 WARNING Electric shock could occur Avertissement Pour r duire les risques if used outdoors or on wet surfaces de choc letrique ne pas utiliser l ext rieur et ne pas aspirer de mati res humides Technical Details VS 14 VS18 Wiring Diagram Schema lectique Voltage 120 volt 60 hz Vacuum floor 8 6 amp Air flow 117cm Dust bag 1 3 gal 3 layer Electrode anti statique Static Electrode Brush motor 1 4 1 a amp Dai ao ie ri racc rd Brush width 12 3 4 16 3 4 inches Brush drive non2. 133 134 135 136 Article no 2538 4033 ER 4028 2091 2458 2047 4022 UE 0512 1 2025 4024 4532 ER 2531 hg 0102 0103 0174 0111 TL VS 18 Designation Support d embout Rouleau de brosse Barrette de brosse Bloc roulement gauche Poulie de brosse Bloc de roulement droit Moteur de brosse Charbon p moteur de brosse Poulie moteur Courroie Contr l lectrique 120 V Levier de support Ressort Vis F 3 9 x 13 DIN 7981 Vis C 3 9 x 16 DIN 7981 Vis C 3 9 x 22 DIN 7981 Vis AM5 x 30 DIN 7985 Pos 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 16 117 118 119 20 121 123 Product Code 4547 WI 2542 4529 BL 4522 hg 4519 dg 4523 2528 or 2010 4009 DG 2014 2622 dg 4012 4019 4006 4072 dg 2510 HG 2541 UL 2546 2534 2530 HG 2538 4033 ER 4028 2091 2458 2047 4022 UE 0512 1 2025 4024 4532 ER 2531 hg 2545 0102 0103 0174 O111TL Description Cover Brush strip cover Chassis cpl Bumper Axle cpl Axle only Foot pedal Axle spring Wheel and end clip Axle clamp Pile adjustment knob Pile adjustment lever Spring Pile adjustment axle Pile adjustment wheel Swivel neck assembly Wire swivel neck Leaf spring Control lever Swivel neck cover Swivel support Brush assembly Brush strip Bearing block l h Brush roller pulley Bearing block r h Brush motor 120 Y 200 W Carbon brush set brush motor Motor pulley
3. UE 0512 1 2025 4024 2572 ER 2531 hg 2545 0102 0103 0174 0111TL Description Cover assembly Brush strip cover Chassis cpl Bumper Axle assembly Axle only Foot pedal Axle spring Wheel and end clip Axle clamp Pile adjustment knob Spring Pile adjustment axle Pile adjustment wheel Swivel neck assembly Wire swivel neck Leaf spring Control lever Swivel neck cover Swivel support Brush assembly cpl Brush strip Bearing block I h Brush roller pulley Bearing block r h Brush motor 120 V 150 W Carbon brush set brush motor Motor pulley Drive belt Electronic control PC board Support lever Return spring Screw F 3 8 x 13 DIN 7981 Screw C 3 9 x 16 DIN 7981 Screw C 3 9 x 22 DIN 7981 Screw AM5 x 30 DIN 7985 Pos Article 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 no 4547 WI 2542 4529 BL 4522 hg 4519 dg 4523 2528 or 2010 4009 DG 2014 2622 dg 4012 4019 4006 4072 dg 2510 HG 2541 UL 2546 2534 2530 HG Designation Carter superieur moteur Couvercle de barrette Chassis Pare choc Axe cpl Axe Pedale de pied Ressort d axe Roue et clips de roue Bride de serrage Bouton de reglage Levier d adjustment Ressort Axe Roue de reglage Articulation cpl C ble lectrique Ressort plat Levier contr le Couvercle d articulation Pos 120 121 422 123 124 125 126 127 128 129 130 131 132
4. show at position number one the brush strip is worn out and must be replaced Red light The brush has become blocked and is not turning Switch off Unplug from the outlet and clear the blockage Filter level indicator If warning light 18 comes on check a Is the dust bag full b Is there a blockage in the hose or power head Maintenance CAUTION Always unplug machi ne at mains outlet before dis mantling any part of the machine For guarantee use only genuine Windsor Parts e g Filter Bags Filters Brush strip etc Changing the paper bag To change the dust bag Remove back cover Push down lever 20 Lower dust bag from connecting tube Close aperture of dust bag top with cardboard cover 21 A To fit new dust bag Insert top of dust bag 21 into slot 22 Push lever 20 down and fit aperture of dust bag top over connecting tube Return lever so that it is in horizontal position Changing filters Vacuum motor filters 23 Replace after ca 20 paper bags have been used Exhaust filter 24 Change when it becomes dirty Press the button 25 and pull the filter for wards To insert a new filter locate the filter into the motor housing and push up until the button 25 engages into place Clearing blockages If the bag full warning light shows before the dust bag is full check for blockages Release the hose by squeezing the tabs of the retaining ring 11 Reverse the hose and put the wand en
5. to be safe when used to perform cleaning functions Should damage occur to electrical or mechanical parts cleaner should be repaired by WINDSOR or competent service station before using in order to avoid further damage to machine or physical injury to user A damaged power cord could cause electrical shock and or fire To minimize this possibility observe the following precautions Do not run cleaner over power cord Avoid closing doors on power cord pulling it around sharp edges or placing sharp edged objects upon it Wind cord no tighter than is necessary to retain it on the cord hooks When disconnecting power cord from electrical outlet grasp the plug Pulling it out by the cord itself can damage cord insulation and internal connections to plug Your vacuum cleaner creates suction and contains a revolving brush To avoid bodily injury from suction or moving parts vacuum cleaner brush should not be placed against or in close proximity of loose clothing jewelry hair or body surfaces while cleaner is connected to electrical outlet Cleaner should not be used to vacuum clothing while it is being worn Keep children away from machine when in operation or plugged in If used on plush carpet or carpet with thick padding turn off unit when handle is in upright position When using accessory tools keep floor brush off carpet by keeping handle in locked position and lowering handle with one hand to raise brush off floor Operate accessories
6. turned Replace motor seal To remove the power head cover take off the brush strip cover 26 and remove the four large screws 27 from underneath the chassis The cover can then be lifted off Pour enlever le logement du sac poussi re 2 du logement du moteur d aspiration 1 enlever le couvercle plastique et les quatre grandes vis En gardant la t te d aspiration assembl e le logement du sac poussi re peut tre d gag Pour enlever le moteur d aspiration enlever en premier les deux cables noirs de la barre de distribution En les replacant s assurer que le support du moteur est bien log sous le cache noir Celui ci doit ensuite tre ferme ment log sous le moteur d aspiration et le moteur avec son cache et son support fer mement mis en position comme montr dans le logement du moteur d aspiration Bien install il net doit pas pouvoir tre tourn Replacer le joint du moteur Pour ouvrir la t te de brosse enlever la barrette de brosse en d montant la plaquette 26 puis d visser les 4 grande vis 27 plac es sous le ch ssis Le carter peut alors tre enlev Changing the brush roller Push the belt 29 off the motor pulley 30 and remove the four screws which hold in the brush bearing blocks Lift out the bearing blocks evenly When replacing the roller with the bearing blocks push downwards keeping the roller parallel with the chassis To remove the brush roller pulley
7. with other hand Always plug your cleaner into a standard wall outlet Use of extension cord or light socket with inadequate current carrying capacity could result in electric shock or fire hazard Disconnect cleaner from electrical outlet before servicing such as changing bags or belts You could receive bodily injury from moving parts of machine should switch accidentally be turned on Disconnect cleaner from electrical outlet before detaching powerhead Do not use your vacuum cleaner in areas where flammable and or explosive vapor or dust is present to avoid possibility of fire or explosion Some cleaning fluids can produce such vapors Areas on which cleaning fluids have been used should be completely dry and thoroughly aired before being vacuumed To avoid fire hazard do not pick up matches fireplace ashes or smoking material with cleaner Keep your work area well lighted to avoid picking up harmful materials such as liquids sharp objects or burning substances and avoid tripping accidents Use care when operating the cleaner on irregular surfaces such as stairs A falling cleaner could cause bodily injury and or mechanical damage Proper storage of machine in an out of the way area immediately after use will also prevent accidents caused by tripping over cleaner Store your vacuum indoors in a cool dry area not exposed to the weather to avoid electrical shock and or cleaner damage Exercise strict supervision to prevent injury w
8. 111 50 0140 51 1034 hg Pos Article no 34 1798 dg 35 1896 36 1553 37 0819 dg 38 1887 UL 39 0511 1 40 1821 UL 41 1411 42 1047 43 1545 UL 44 12653 UL 45 1524 46 0101 47 0102 48 0103 49 0111 50 0140 51 1034 hg Description Cable VS 14 Cable VS 18 Handle grip Handle cover Handle Dust bag housing Grommet Switch button Connecting tube Retaining ring Switch Switch cover Switch holder Prited circuit board PC board cover Antistatic wire Internal cable Cable clamp Switch housing cover Dust bag lever Return spring Leaf spring Connecting rod Clamp Motor filter Exhaust filter Back cover Back cover seal Gasket Latch with spring and pin Cable hook Cable hook turnable Hand nozzle Hose Motor housing Housing cover r h Filter retaining button Sound insulation Locking rod Locking catch Vac motor 120V 1000W lamb Carbon brush set vac mot Motor cover Motor support Vac motor seal Contact holder 3 wire Terminal block 3 wire Terminal block cover Screw C 3 9 x 9 5 DIN 7981 Screw F 3 9 x 13 DIN 7981 Screw C 3 9 x 16 DIN 7981 Screw AM5 x 30 DIN 7985 Washer 4 4 DIN 125 Retaining ring Designation Bouton de fittre Isolation phonique Baguette Verrou Turbine aspir 120 V 1000 W Charbon p turbine aspiration Couvercle moteur Support de moteur Joint moteur d aspiration Prise femelle Boitier de raccord Couvercle Vis C 3 9 x 9 5 DIN 7981 Vis F 3
9. 31 hold the roller in one hand and turn the pulley in a clockwise direction To remove the motor pulley 30 insert a screwdriver into a groove and give a light tap in an anticlockwise direction The loosened pulley can then be removed Changing the Electronic Controller 34 Disconnect the lead from the motor Lift the controller upwards from the motor Lift the controller upwards from its location and then disconnect the lead from the swivel neck To remove the swivel neck 35 take out the two small screws 36 from the swivel neck supports 37 then lift the swivel neck assembly from the chassis On re assembly check that the leads from the swivel neck do not become trapped when the power head cover is replaced To remove the swivel neck cover take out the retaining screw 38 and slide the cover 39 downwards then lift out On re assembly check that the leads do not become trapped To remove the axle assembly unscrew the three screws and take off the axle clamps Before replacing lightly grease the axle To replace hook one end of the spring on the axle then grip the other end with a pair of pliers and turn about a quarter of a turn Keeping the wheels at the ends of the axle press the axle assembly black into place Changement du rouleau de brosse Faire sauter la courroie crant e 29 de la partie moteur 30 et d visser les 4 vis qu tiennent le supports de brosse Tirer le rouleau de brosse Pour replacer pro
10. 9 x 13 DIN 7981 Vis C 3 9 x 16 DIN 7981 Vis AMS x 30 DIN 7985 Rondelte 4 3 DIN 125 Clips plastique Pos 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 118 Article no 2635 WI 2542 2543 BL 2522 hg 2539 dg 2525 2528 or 2010 2012 DG 2014 2622 dg 4019 2524 4072 dg 2510 HG 2541 UL 2546 2534 2530 HG Designation Carter superieur moteur Couvercle de barrette Chassis cpl Pare choc Axe complet assemble Axe Pedale de pied Ressort d axe Roue et clips de roue Bride de serrage Bouton de reglage Ressort Axe de roue Roue de reglage Articulation cpl C ble lectrique Ressort plat Levier contr le Couvercle d articulation 127 133 134 135 Article no 2538 2030 ER 2046 2091 2458 2047 2241 UE 0512 1 2025 4024 2572 ER 2531 hg 2545 0102 0103 0174 0111 TL VS 14 Designation Support d embout Rouleau de brosse Barrette de brosse Bloc roulement gauche Poulie de brosse Bloc de roulement droit Moteur de brosse Charbon p moteur de brosse Poulie moteur Courroie Contr l lectrique 120 V Levier de support Ressort Vis F 3 9 x 13 DIN 7981 Vis C 3 9 x 16 DIN 7981 Vis C 3 9 x 22 DIN 7981 Vis AM5 x 30 DIN 7985 Pos Product Code 2635 W 2542 2543 BL 2522 hg 2539 dg 2525 2528 or 2010 2012 DG 2014 2622 dg 4019 2524 4072 dg 2510 HG 2541 UL 2546 2534 2530 HG 2538 2030 ER 2046 2091 2458 2047 2241
11. WINDSOR En SP mg VERSAMATIC ur VS 14 VS 18 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions must always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE WARNING ro reduce the risk of fire electric shock or injury 1 Do not leave appliance when plugged in Unplug from outlet when not in use and before servicing 2 Do not use outdoors or on wet surfaces 3 Do not use near small children Do not allow to be used as a toy Close attention is necessary when used by or near children 4 Use only as described in this manual Use only manufacturer s recommended attachments 5 Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water return it to a service center 6 Do nat pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or comers Do not run appliance over cord Keep cord away from heated surfaces 7 Do not unplug by pulling on cord To unplug grasp the plug not the cord 8 Do not handle plug or appliance with wet hands 9 Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce air flow 10 Keep hair loose clothing fingers and all parts of body away from openings and moving parts Do not place fingers or other body parts under
12. bt as to whether the outlet is properly grounded Do not modify the plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician This appliance is for use on a nominal 120 volt circuit and has a grounded plug that looks like the plug illustrated in sketch A A temporary adaptor that looks like the adaptor illustrated in sketches A and C may be used to connect this plug to a 2 pole receptacle as shown in sketch E if a properly grounded outlet is not available The temporary adaptor should be used only until a properly grounded outlet sketch A can be installed by a qualified electrician The green colored rigid ear lug or the like extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover Whenever the adaptor is used it must be held in place by a metal screw Note In Canada the use of a temporary adaptor is not permitted by the Canadian Electrical Code ADAPTER SRE DD OUTLET METAL SCREW GROUNDED __ 7 11 TAB FOR OUTLET BOX GROUNDING SCREW A 8 tc Important Safeguards Accidents due to misuse can only be prevented by those using the machine To guard against injury basic safety precautions should be observed including the following Read and follow all safety instructions WARNING ELECTRIC SHOCK COULD OCCURIF USED OUTDOORS OR ON WET SURFACES This vacuum cleaner is designed
13. c der l inverse en tant tr s attentif au positionnement des supports de brosse Pour enlever la poulie 31 de la brosse tenir le rouleau de brosse dans une main et tourner la poulie dans le sens des aiguilles d une montre Pour enlever la poulie du moteur 80 ins rer un tournevis dans le sabot et taper l g rement avec un marteau dans les sens contraire des aiguilles d une montre Changement du contr ler lectronique 34 Deconnecter les fils du moteur et tirer Pour entever embout pivotant 37 enlever les 2 petites vis 36 qui tiennent les flasques sur le ch ssis ensuite tirer l embout Pour enlever le carter de l embout pivotant oter les 2 vis 38 et tirer le carter 39 Pour enlever l axe complet d visser les 3 vis t te cruciforme et enlever les attaches de l axe Avant de remonter graisser l g rement l axe Pour remonter accrocher un bout du ressort l axe puis serrer l autre bout avec une paire de pince et tourner d environ un quart de tour En gardant les roues aux bouts de l axe remettre l ensemble en pressant puis visser Pos Article no de SVONDA D 1910 1918 1037 EH 1596 hg 1794 1949 bl 1420 hg 1548 hg 1038 bl 1792 hg 0517 1280 1069 UL 1477 UL 1281 0818 1283 UL Designation Cable VS 14 C ble VS 18 Poignee Couvercle de poignee Manche aluminium Logement sac poussi re Passe c ble Couvercle d interrupteur Tube de conne
14. cle aspiration Ensemble moteur de brosse soa Montage Assemblage Pr senter verticalement la partie aspiration e l ins rer dans la t te de brossage Alligner le renflement 13 sur celui de l articulation 14 et enfoncer Le levier de blocage 15 doit tre tourn sur la gauche pendant l op ration Remettre le levier de blocage en position verticale une fois la partie aspirante mise en place Connexion du flexible d aspiration Introduire l embout noir du flexible dans le tube droit d aspiration 12 jusqu entendre un d clic Pour d connecter le flexible presser de chaque cot du clip de verrouillage 11 et tirer sur le flexible Position de travail Pour mettre en position et en marche appuy er Sur la p dale 16 Quand l appareil est sous tension la t te de brossage s arr te et se met en route avec Vinclinaison de la partie aspirante Mise en marche de la t te d aspiration Le moteur de la t te d aspiration s arr te automatiquement quand le flexible main 17 est tir et red marre automatiquement quand il est r ins r Si la t te d aspiration ne d marre pas v rifier que le flexible main est bien enfonc Brush controller The electronic brush controller monitors the operation of the brush Green light Brush correctly set and running Green light and red light Adjust the brush setting by turning the Pile adjustment knob 19 to a lower number If the lights still
15. ction Clips plastique Contacteur Bouton de contact avec protection plastique Blocage de Pinterrupteur Circuit imprim Couverture plastique pour plaque de circuit imprim Cable Cable lectrique Pos Article no 15 1030 UL 16 1026 UL 17 1040 18 1041 19 1027 20 1025 21 1073 22 1044 23 1534 hg 24 1139 bt 25 1059 26 1061 27 1057 BL 28 1461 bl 29 1462 BL 30 1517 hg 31 1516 hg 32 1797 WI 33 1521 hg VS 14 VS 18 28 7 D a J f ges 7 SED LR Dmg EE EE EE o mm MS N A Designation Bride de serrage Couvercle boitier interrupteur Verrouillage du sac Ressort Ressort Tringle securit Bride de serrage Filtre moteur d aspiration Filtre sortie d air Couvercle arriere Joint d etachette air Joint Verrou de couvercle Crochet de c ble Crochet de c ble tournant Tube Flexible Carter de turbine Carter de logement Pos Product Code 1 1910 1918 2 1037 EH 3 1596 hg 4 1794 5 1949 b 6 1420 hg 7 1548 hg 8 1038 bl 9 1792 hg 10 0517 1280 11 1069 UL 12 1477 UL 1281 13 0818 14 1283 UL 15 1030 UL 6 1026 UL 17 1040 18 1041 19 1027 20 1025 21 1073 22 1044 23 1534 hg 24 1139 bl 25 1059 26 1061 27 1057 BL 28 1461 b 29 1462 BL 30 1517 hg 31 1516 hg 32 1797 W 33 1521 hg 34 1798 dg 35 1896 36 1553 37 0819 dg 38 1887 UL 39 0511 1 40 1821 UL 41 1411 42 1047 43 1545 UL 44 1265 UL 45 1524 46 0101 47 0102 48 0103 49 0
16. d into the connecting tube 12 Remove the obstruction by switching on the machine holding the hose upright If necessary rapidly lift your hand on and off the end of the hose Never use a stick to clear the hose Changing the brush strip To replace brush strip Remove brush strip cover 26 Turn brush roller so that the brush strip can then be pulled out Ensure that the new brush strip is fully inserted N B Replace the brush strip before the brist les wear down to the level of the support rod Contr leur de brosse Les voyants lumineux lectroniques plac s sur la t te de brosse contr lent le positionne ment de la brosse Lumi re verte Brosse tournant correcte ment et bien r gl e Lumi re verte et rouge R gler la brosse en tournant le bouton de r glage 19 vers le chiffre inf rieur Si la lumi re est encore rouge la position 1 la barrette de brosse est us ee et il faut la changer Lumi re rouge La brosse est bloqu e et ne tourne pas Arr ter les moteurs et proc der au cont le qui est souvent un simple nettoyage Indicateur de remplissage du sac Si la lampe tension s allume 18 v rifier que le sac poussi re ne soit pas plein qu il n y a rien de coinc dans les tuyaux ou dans la t te d aspiration Entretien Toujours d brancher la machine avant de d monter quelque partie que ce soit Pour la garantie employer uniquement des pi ces d origine WINDSOR Ex sacs filtrants f
17. hen using vacuum cleaner near children or when child is allowed to operate vacuum cleaner Do not allow children to play with vacuum cleaner and never leave cleaner plugged in and unattended SAVE THESE INSTRUCTIONS ar zen per OR LG T EE VERSAMATIC VS 14 VS 18 Vacuum motor housing Dustbag housing Suction hose On off switch Cables cleats Carrying recess Back cover Power head OnNOOh WN Assembling the vacuum cleaner Hold the vacuum section in the vertical position and insert into the power head Locate the line 13 on the motor housing accurately opposite the rib on the swivel neck 14 The locking catch 15 must be turned to the left during the locating Secure the vacuum section in place the turning the locking catch to the vertical position Attaching suction hose Push the black end of the hose into the connecting tube 12 so that it clicks into place To disconnect the hose press the retaining ring 11 and pull the hose out of tube Swivel neck latch To release the machine from the upright position depress the foot pedal 16 Power head on Power head motor stops automatically when hand nozzle 17 is withdrawn and restarts automatically when reinserted If power head does not start check that hand nozzle is fully inserted Turbine d aspiration Emplacement sac poussi re Flexible d aspiration Interrupteur mise en route Support de c ble Poign e de portage Couver
18. iltres brosse etc Changement du sac papier Pour changer le sac poussi re enlever le couvercle plastique puis pousser le levier vers le bas 20 et sortir le sac par le bas du tube de connection Pour ajuster le nouveau sac poussi re ins rer son sommet 21 dans la fente 22 puis pousser le levier 20 vers le bas et installer l ouverture du sac poussi re de facon ce qu il soit dans une position horizontale Changement du filtre Fittre du moteur d aspiration 23 nous vous conseillons de le remplacer environ tous le 20 sacs poussi res Quand le filtre de sortie d air 24 est devenu fonc sale il doit tre remplac Appuyer sur le bouton 25 et tirer le filtre Pour mettre le nouveau filtre positionner le filtre dans le bas du carter et pousser jusqu ce que le bouton 25 se sait remis en place Anomalies Si le voyant du remplissage du sac s allume alors qu il n est pas plein v rifier que le tube d aspiration n est pas bouch Pour le d boucher inverser le flexible en branchant l embout noir sur le haut de la machine apr s l avoir d fait de son tube Mettre l appareil en marche en levant et secouant l gerement le tube Ne jamais utiliser de manche vous risqueriez d endommager le flexible Changement de la barrette de brosse Pour changer la barrette de brosse d visser la plaquette 26 puis tourner le rouleau de brosse de facon amener la barrette en face de la sortie Toujours s assu
19. rer que la nouvelle barrette de brosse est compl tement ins r e Service Instructions Entretien ATTENTION L entretien et les r parations doivent tre effectu s par un personnel qualifie AVERTISSEMENT Pour eviter les risques de choc lectrique debrancher avant le nettoyage ou la maintenance Maintenance CAUTION Maintenance and repairs must be done by qualified personnel WARNING To reduce the risk of electric shock unplug before cleaning or servicing Lu ss E My TIRA GER AT Os The switch housing cover is removed by taking out the three screws then lifting off Circuit board 33 can be removed by loosening screw 32 Le couvercle de protektion de l interrupteur s enl ve apr s avoir d viss les 3 vis puis soulev celui ci Le circuit imprim 33 s enl ve apr s avoir enlev la vis 32 To remove the dust bag housing 2 from the vacuum motor housing 1 take off the back cover and remove the four large screws Keeping the power head attached the dust bag housing can be eased off To remove the vacuum motor first detach the two black wires from the terminal block When replacing ensure that the motor sup port is fully located onto the motor cover The motor cover should then be firmly loca ted onto the vacuum motor and the motor with its cover and support firmly seated into position as shown in the vacuum motor housing When properly seated the motor cannot be
20. slip drive belt Connection with electronic overload protection LL Interupteur de moteur de brossa Brush Motor Switch Brush strip replaceable Height 46 inches A Width 14 16 inches Weight 16 16 lbs Vaio i 1 Cerone Conta Details Techniques VS 14 VS18 Voltage 120 volt 60 hz Moteur aspiration 900 watts Colonne d eau 2040 mm D bit d air 55 l sec Moteur de brosse 150 200 watts Capacit sac poussi re 15 3 litres Largeur de travail 325 425 mm WINDSOR INDUSTRIES INC Barrette de brosse interchangeable 1351 West Stanford Ave Hauteur 1225 mm Englewood Colorado 80110 USA Largeur 360 460 mm 800 444 7654 303 762 1600 FAX 303 762 0817 06397 11 99 Poids 8 9 ka
21. vacuum unless unplugged 11 Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes 12 Do not use without dust bag and or filters in place 13 Turn off all controls before unplugging 14 Use extra care when cleaning on stairs 15 Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present 16 Machines can cause a fire when operated near flammable vapors or materials Do not operate this machine near flammable fluids dust or vapors 17 Maintenance and repairs must be done by qualified personnel 18 Connect to a properly grounded outlet only See Grounding Instructions 19 Do not use machine as a step 20 If used on plush carpet or carpet with thick padding do not leave machine in one place with machine turned on SAVE THESE INSTRUCTIONS GROUNDING This appliance must be grounded If it should malfunction or breakdown grounding provides a path of least resistance for electric current to reduce the risk of electric shock This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service person if you are in dou
Download Pdf Manuals
Related Search