EarthQuake MiniMe P8 User`s manual
Contents
1. Iin am a K KV I AL WVVVW Placing the subwoofer in the corner of the room will produce a more boomy effect often preferred for movies and sound tracks For a music application place the subwoofer as shown above or against the front wall about a third of the room width Dual Subwoofer Setup with Mono Signal This is a BETTER setup In a dual subwoofer setup the subharmonic frequencies black arrow always move towards the middle of the room while the lows mids and highs follow the action gray arrow A Lee NY Notice the breakaway and image separation Is less in this setup than the single subwoofer setup MiniMe P8v2 P8Wv2 Manual 9 Connecting Your Subwoofer s Low Level Setup Single Sub This is the best way to drive an audio signal into the MiniMe P8v2 P8Wvz Today all signal processors 5 1 6 1 and more advanced ones come equipped with built in pre amplifier outputs RCA that include a subwoofer output Generally the SUB PRE OUT is in mono format Connect the SUB PRE OUT from the processor receiver to the MiniMe P8v2 P8Wv2 s LOW LEVEL INPUT using a Y RCA cable We strongly recommend that you use the best available RCA connectors and cables High quality cables are normally triple shielded and the connectors are gold plated with forceful grasping When using this connection the MiniMe P8v2 P8Wv2 only receives bass signals from the source Therefore the cro2. e Check for any visual signs of damage If you encounter any concealed damage consult your Earthquake Sound dealer before proceeding with unit installation e Retain the sales receipt as it establishes the duration of the limited warranty and provides information for insurance purposes The MiniMe is packaged well for safety We highly suggest having a padded surface when unpacking it Step 1 On a padded surface carefully place the box on its side to remove the bottom packing tape and staples the bottom flaps outward and keep the Step 2 Without tilting the box too much tug ff protective foam in place l 3 Step 3 Gently reposition the box upright Step 4 Slide the box off minding the protective foam on the top bottom and sides of the subwoofer This triangle which appears on your component alerts you to important operating and maintenance instructions in this aaa accompanying literature MiniMe P8v2 P8Wv2 Manual Introduction The MiniMe system is designed to dramatically enhance your enjoyment of music and films at home by adding power and impact to low frequency sound effects without taking up your entire living space Congratulations and thank you for choosing the Earthquake MiniMe P8v2 P8Wv2 subwoofer as a key component of your audiophile system The MiniMe P8v2 P8Wvz subwoofer utilizes an advanced digital class D amplifier an 8 premium long throw driver and an 8 pas
3. lt WARNING NOTEXPOSE 410 120V ALFIED cece Per ay CAUTION RISI o 3 NOT C OPEN WARNING SHOCK HAZARD DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR MANUFACTURED BY EARTHQUAKE SOUND CORPORATION THS APPLIANCE TO pam OR MOISTI PARTS INSII RVICING 2727 MCCONE AVENUE HAYWARD CA 94545 WWW EARTHQUAKESOUND COM Aa 110 120V 60Hz T3 15AL 250V 220 240V 50Hz T1 6AL 250V p 10 11 7 Low Level RCA Inputs This the best way to drive audio signal to the MiniMe FF 8v2 NOTE DO NOT USE HIGH LEVEL AND LOW LEVEL INPUTS AT THE SAME TIME 8 LFE SUB Operation Mode Switch When the switch is in LFE position the subwoofer is running in full range mode 20Hz 2kHz and the frequency adjustment is disabled When the switch is in SUB position the subwoofer reverts to manual frequency adjustment allowing the user to operate and fine tune the subwoofer to his her preference 9 AUTO ON OFF Switch This is a 3 way switch When ON the amplifier will remain on regardless of signal presence When set to AUTO the amplifier will only turn on when audio signal is detected Additionally the amplifier will go to sleep stand by if it does not detect any signal after 15 minutes When set to OFF the amplifier will remain off regardless of signal presence Note that the D MAIN POWER switch must be ON for this feature to work 10 Main Power Switch When switched OFF the amplifier will remai
4. You will notice a lack of bass from your subwoofer if you inadvertently reverse one of the connections i e red to black In case the MiniMe P8v2 P8Wvz becomes out of phase with the main front speakers adjust the phase shift to correct the problem Note that maximum bass is only achieved when the sub is in phase with the speakers in your system 000000 SUR BACK R S processor receiver 8 yt NOTE DO NOT USE HIGH LEVEL AND LOW LEVELINPUTS AT THE SAME TIME back of typical Specifications are subject to change without notice MiniMe P8v2 P8Wv2 Manual 11 Connecting Your Subwoofer s contd High Level Single Sub Satellite Setup The MiniMe P8v2 P8Wvz has a high speaker level output connection that can be used to drive the stereo front or rear speakers Using speaker wires up to 16 gauge simply connect the receiver s front speaker outputs to the MiniMe P8v2 P8Wve2 speaker level inputs Then using speaker wires connect the MiniMe P8v2 P8Wvz2 speaker level outputs to the speakers Remember to always connect red to red and black to black when making connections between a receiver processor to the subwoofer You will notice a lack of bass from your subwoofer if you inadvertently reverse one of the connections i e red to black NOTE In case the subwoofer with becomes out of phase with the main front speakers adjust the phase shift to DO NOT USE HIGH LEVEL AND LOW correct th
5. Earthquake pays for labor parts and ground freight only in US mainland not including Alaska and Hawaii Shipping to us is not covered e Second third fourth amp fifth year Earthquake pays labor only Customer must pay for parts and freight both ways B Warning e Products sentin for repair that are tested by Earthquake technicians and deemed to have no problem will not be covered by the limited warranty Customer will be charged a minimum of one 1 hour of labor at ongoing rate plus shipping charges back to customer e Each product sent in for repair must be packaged in its original packaging Otherwise repackaging charges will apply in addition to the labor parts and shipping charges C Earthquake will repair or replace at our option all defective products parts subject to the following e Defective products parts have not been altered or repaired by anyone other than an Earthquake factory approved technician e Products parts are not subjected to negligence misuse accident or damage by improper line voltage e Products parts were used with incompatible products e The serial number or any part of the product has been altered defaced or removed e Products parts have been used in any way that is contrary to Earthquake s written instructions D Warranty Limitations Warranty does not cover products that have been modified or abused including but not limited to the following e Damages to speaker cabinet
6. A Phone 510 732 1000 Fax 510 732 1095
7. Achievement award at the 2011 Consumer Electronic Show Just recently the US Department of Commerce presented Earthquake Sound with another Export Achievement award for expanding its export operations in China AEAEE He tee A anansen ions aA x Joseph Sahyoun US Secretary of Commerce Gary Locke US Commercial Officer Sarah Fox and Joseph Sahyoun Abraham Sahyoun and Thomas Mygind GUIDE Ce e OJS Sri yf ay dome Theater Best of High Fidelity DESIGN amp ENGINEERING NOVATIONS INTERNATIONAL CES SMALL SUBWOOFERS Earthquake Supernova MKV1 10 Subwoofer INNOVATIONS INTERNATIONAL CES PLATINUM AWARD Q IN Specifications are subject to change without notice MiniMe P8v2 P8Wv2 Manual 3 Safety Instructions Safety First This documentation contains general safety installation and operating instructions for the MiniMe P8v2 P8Wvz subwoofer It is important to read this users manual before attempting to use this product Pay particular attention to the safety instructions Appears on the component to indicate the presence of uninsulated dangerous voltage Symbols Explained inside the enclosure voltage that may be sufficient to constitute a risk of shock AUTION Calls attention to a procedure practice condition or the like that if not correctly performed or adhered to could result in injury or death Calls attention to a procedure WARNING practice con
8. EVELINPUTS AT THE SAME TIME back of typical processor receiver MiniMe P8v2 P8Wv2 Manual 13 Adjusting the controls There are two main methods for adjusting the level crossover frequency and phase of the Earthquake MiniMe P8v2 P8Wvzto match a system e Method 1 Typical By listening and making adjustments to suit your preference e Method 2 Laboratory By measuring the output and adjusting for a flat frequency response Satisfactory results can be achieved if you make the adjustments based simply on listening This is Earthquake s preferred method as it allows the system to be voiced based on what sounds the best whereas laboratory flat frequency response can often be clinical and less than exciting The following procedures are for those who prefer a more methodical and scientific approach You will need a test CD with low frequency warble tones and an SPL meter Step 1 Disconnect the subwoofer and run the main speaker with a tone in its passband 80 100Hz Measure the level Step 2 Disconnect the main speaker and reconnect the subwoofer Set the subwoofer to its highest crossover frequency Set the VOLUME of the subwoofer to give the same sound pressure level with the same tone you used in Step 1 Step 3 With both the subwoofer and the main speaker connected measure the level of the tones at the available frequencies Because the crossover is set to high you will have a peaked resp
9. PAM AGUAAL The Sound That Will Move You MINIME P8v2 P8Wv2 USER S MANUAL Earthquake Sound Corp 510 732 1000 U S Toll Free 800 576 7944 www earthquakesound com Table of Contents About Earthquake Sound Corporation ccccccccseccseeeeseeeeeeeeeeeeeeeaes 3 Safety INStrUctiONS cccccceccseececseeecsececaeeeseeeeseaeeseeesseeesseeeesaeesseeeees 4 5 HVE CUCU OVA s sree A EE 6 What Makes a MiInIMG siessieccdcor casccsieessaicasanssaceetuesincndeaecsvaedicpntieesasasan 6 Control Panel OVErvieW cccceecececcecececeecececeececeeaeceenseeaeeneueaeeneneaeans 7 8 Placing Your SUDWOOTCN S 1cacsincncssadenndannnciywsessinitausiensantarnbearsannabokienive 9 Connecting Your SUDWOOPEr S ccccssececesseeceeseeeceseeeceseeesseseeseeeeeses 10 13 Adjusting Your SUDWOOfEer S ccccseeeeceeeeecceeeeeceeseeceeseessseeesenseeseaes 14 DIMENSIONS and SPECIFICATIONS c ccc ecccceececeeeeceeeeceeeeceeeeseneesseeessaees 15 Warranty WATOMMAUOMsai cnz cbccasasndiasecnasiconsesanendaneteaninciasatcedaacotaumeneaeiannede 16 17 FOF YOUR ROCO esna a E A 18 WARNING This product is capable of generating high sound pressure levels You should exercise caution when operating these speakers Long term exposures to high levels of The Sound That Will Move You sound pressure will cause permanent Earthquake Sound Corporation damage to your hearing Sound pressure 2727 McCone A
10. and cabinet finish due to misuse abuse or improper use of cleaning materials methods e Bent speaker frame broken speaker connectors hole s in speaker cone hole s in surround amp dust cap and burnt speaker voice coil e Fading and or deterioration of speaker components amp finish due to improper exposure to elements e Bent amplifier casing damaged finish on the casing due to abuse misuse or improper use of cleaning material e Burnt tracers on PCB e Product part damaged due to poor packaging or abusive shipping conditions e Subsequent damage to other products Awarranty claim will not be valid if the warranty registration card is not properly filled amp returned to Earthquake with a copy of the sales receipt E Service Request To receive product service contact Earthquake Service Department at 510 732 1000 and request an RMA number Return Material Authorization Items shipped without a valid RMA number will be refused Make sure you provide us with your complete correct shipping address a valid phone number and a brief description of the problem you are experiencing with the product In most cases our technicians might be able to resolve the problem over the phone thus eliminating the need to ship the product 16 MiniMe FF8v2 Manual Earthquake Sound Corp 800 576 7944 www earthquakesound com F Shipping Instructions Product s must be packaged in its original protective box es to minimize transport damag
11. dition or the like that if not correctly performed or adhered to could result in damage to or destruction of part or all of the product NOTE Calls attention to information that is essential to highlight Important Safety Instructions 1 Read these instructions in their entirety 2 Store this manual and packaging in a safe place 3 Heed all warnings 4 Follow instructions do not take shortcuts 5 Do not use this apparatus near water 6 Clean only with a dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatuses that produce heat 4 MiniMe P8v2 P8Wvz2 Manual 9 Donotdefeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other The grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or 11 12 13 14 pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments and accessories specified by the manufacturer Use only a compatible rack or cart for the final r
12. e and prevent repackaging cost at the ongoing rates Shipper claims regarding items damaged in transit must be presented to carrier Earthquake Sound Corporation reserves the right to refuse improperly packed product A copy of the original sales receipt must accompany product returned to service We encourage you to include with the package a written description of the problem Ship product to Earthquake Sound Corp 2727 McCone Avenue Hayward CA 94545 Tel 510 732 1000 You are responsible for the cost of shipping the product to Earthquake Sound Corporation G Disputes Resolution All disputes between clients and Earthquake Sound Corporation resulting from the five 5 year limited warranty policy must be resolved according to the laws amp registration of the county of Alameda California Specifications are subject to change without notice MiniMe P8v2 P8Wvz2 Manual 17 For Your Records Date of Purchase Authorized Dealer Installer Info Name Address Phone Notes 18 MiniMe P8v2 P8Wvz Manual Earthquake Sound Corp 800 576 7944 www earthquakesound com Specifications are subject to change without notice MiniMe P8v2 P8Wvz Manual 19 CAN ANVAAD CE Tae law a ia DB The Sound That Will Move You Earthquake Sound reserves the right to amend details of the specifications without notice Copyright Earthquake Sound Corporation Earthquake Sound Corporation 2727 McCone Avenue Hayward CA 94545 US
13. e bass response and whether signal is being fed to the amplifier Note that this LED will only light up when the main power switch is in the ON position No Red OFF NOTE DO NOT USE HIGH LEVEL AND LOW LEVEL INPUTS AT THE SAME TIME 5 High Level Inputs Outputs These clamp style input terminals allows the MiniMe FF8vz2 amplifier to receive signal from the amplifier or receiver that is powering the surround speakers The output terminals allows the MiniMe FF8vzto drive stereo satellite speakers AUTO 2 Volume Control This knob allows the user to control the volume of the subwoofer Always start at the lowest setting and slowly increase the volume until the desired subwoofer level is reached 6 110V 220V AC Selector The MiniMe P8v2 P8Wvz2 can operate in a 110 120V or 220 240V environment Simply slide the selector to the required power setting and replace the fuse to the proper rating prior to connecting the subwoofer to a power source 3 50 160Hz Frequency Adjustment This knob allows user to set the subwoofer s cut off frequency Signals above the set crossover frequency will be gradually rolled off to prevent them from interfering with the surround speakers Specifications are subject to change without notice MiniMe P8v2 P8Wv2 Manual Control Panel Overview continued HAN HUANG CE Tae iy a law BD The Sound That Will Move You DESIGNED IN THE USA a
14. e construction and reinforced dust cap the MiniMe P8v2 P8Wvz2 driver effortlessly produces phenomenal bass with extremely low distortion while staying cool the entire time 6 MiniMe P8v2 P8Wv2 Manual allowing the passive driver to move the same amount of air in either direction Coupled with the active driver the SLAPS enables the sub to deliver louder bass without using more power from the amplifier Luxurious Piano Gloss Cabinet The deep luxurious piano lacquer begins with a thorough sanding and priming followed by multiple applications of black or white lacquer with additional fine sanding between each layer and finished with a smooth high gloss clear coat When it comes to elegance and style the MiniMe P8v2 P8Wvz delivers Earthquake Sound Corp 800 576 7944 www earthquakesound com Control Panel Overview O POWER LOW LEVEL 2 DO a l lt 4 HARTAUARE S O UND The Sound That Will Move You MANUFACTURED BY EARTHQUAKE SOUND CORPORATION 2727 MCCONE AVENUE HAYWARD CA 94545 110 120V 60Hz T3 15AL 250V WWW EARTHQUAKESOUND COM 220 240V 50Hz T1 6AL 250V J 1 LED Power Signal Indicator 4 0 180 Phase Adjustment This LED indicator reflects the main power status of the amplifier as well as the state of the amplifier whether the AUTO Sensing is on off This 0 180 switch allows user to synchronize the subwoofer to obtain better and more precis
15. e problem Note that maximum bass is only LEVEL INPUTS AT THE SAME TIME achieved when the sub is in phase with the speakers OCEeSesOQ in your system SPEAKER OUTPUT FRONT CENTER SURROUND SUR BACK back of typical R L R L R L AC D O O processor receiver OD XD 6D SA for fir liad OSI NO Fy e QO VO 0 0 fe o o o e fe o Le o O fe o O fo 0 o 0 12 MiniMe P8v2 P8Wv2 Manual Earthquake Sound Corp 800 576 7944 www earthquakesound com High Level Dual Sub Connect the speaker wire up to 16 gauge from the receivers RIGHT SPEAKER OUTPUTS to the MiniMe P8v2 P8Wv2 s RIGHT SPEAKER INPUTS Then connect the speaker wire from the receiver s LEFT SPEAKER OUTPUTS to the MiniMe P8v2 P8Wv2 s LEFT SPEAKER INPUTS Remember to always connect red to red and black to black when making connections between a receiver processor to the subwoofer You will notice a lack of bass from your subwoofer if you inadvertently reverse one of the connections i e red to black In case the subwoofers become out of phase with the main front speakers adjust the phase shift to correct the problem Note that maximum bass is only achieved when the sub is in phase with the speakers in your system doco Specifications are subject to change without notice NOTE DO NOT USE HIGH LEVEL AND LOW L
16. esting position Unplug this apparatus during lightning storms or when unused for a long period of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in a way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture system Installation Considerations There are several factors to consider before installing Earthquake Sound s MiniMe P8v2 P8Wvz2 Subwoofer What are the intended listening zones From where in each zone will the listener prefer to control the system Where will the subwoofer be located Where will the source equipment be located Earthquake Sound Corp 800 576 7944 www earthquakesound com Connection Tips Keep all power cords away from all signal cables to prevent humming from induced noise Choose reliable signal cable cords Earthquake Sound also specializes in high performance RCA cables and patches All speaker wires that are ran through the walls should be twisted type to reduce potential hum noise pick up It is best to use a grounded electrical outlet to power the amplifier Lack of input ground reference could be unsafe Consult with your electrical contractor about pro
17. g Inputs Outputs Additional Features Fuse Ratings Dimensions H x W x D including feet grilles amp amp Specifications are subject to change without notice 10 2 265mm With Amplifier 11 278mm With Feet Ported Enclosure with Passive 320 Watts MAX 8 Premium Extended Excursion Subwoofer 8 Patented SLAPS Symmetrically Loaded Audio Passive System 25Hz 160Hz 50Hz 160Hz AUTO ON OFF Low Level RCA amp High Level Speaker Inputs High Level Speaker Outputs 0 180 Phase Adjustment 110V 220V AC Selector 110 120V 60HZz 5x20mm T3 15AL 250V 220 240V 50Hz g5x20mm T1 6AL 250V 11 x 11 1 2 x 10 1 2 278mm x 290mm x 265mm MiniMe P8v2 P8Wv2z Manual 15 5 Year Limited Warranty Information Earthquake warrants the original purchaser that all Factory Sealed New Audio Products to be free from defects in material and workmanship under normal and proper use for a period of five 5 years from the date of purchase as shown on the original sales receipt with serial number affixed written on it The five 5 year limited warranty period is valid only if an authorized Earthquake dealer properly installs the product and the warranty registration card is properly filled out and sent to Earthquake Sound Corporation If a non authorized party installs the product a ninety 90 day warranty period will be applied A Five 5 years limited warranty plan coverage guidelines e First year
18. ing his existing expertise in the audio industry Joseph Sahyoun expanded his company to home audio production Earthquake Sound has since evolved into a leader in the home audio industry producing not only subwoofers and amplifiers but surround speakers and tactile transducers as well Engineered by audiophiles for audiophiles Earthquake Sound audio products are meticulously crafted to reproduce each and every single note perfectly bringing your home theater experience to life With true dedication and full attention to details Earthquake Sound engineers continuously develop new and better products to meet customers needs and go beyond their expectations From mobile audio to prosound and home audio Earthquake Sound has been selected as the winner of many prestigious awards based on sound quality performance value and features CEA and numerous publications have awarded Earthquake Sound with over a dozen design and engineering awards Additionally Earthquake Sound has been granted many design patents by the USPO for revolutionary audio designs that have changed the sound of the audio industry Headquartered in a 60 000 square foot facility in Hayward California USA Earthquake Sound currently exports to over 60 countries worldwide In 2010 Earthquake Sound expanded its export operations by opening a European warehouse in Denmark This accomplishment was recognized by the US Department of Commerce who honored Earthquake Sound with an Export
19. n off as there is no AC power being fed into it We highly recommend keeping this switch OFF when the subwoofer is not being used for an extended period of time 11 AC Power with Built in Fuse This AC line connector is fused to protect the subwoofer from unwanted power surges Be sure to use the proper fuse rating when replacing the fuse 110 120V 60Hz 5x20mm T3 15AL 250V 220 240V 50Hz 5x20mm T1 6AL 250V To access the fuse compartment simply unplug the subwoofer from any power source place a flat head screw driver in the small notch and pry it open as illustrated below 110 120V 60Hz T3 15AL 250V 220 240V 50Hz T1 6AL 250V 8 MiniMe P8v2 P8Wv2 Manual Earthquake Sound Corp 800 576 7944 www earthquakesound com Placing Your Subwoofer s You often hear the term subwoofers are non directional This is not true It is harder to choose subwoofer placement when low frequencies are crossed The wider the room the more directional the subwoofer The easiest solution is to use two 2 subwoofers feed a mono signal to both and place them in the front one on the left and another on the right While having two 2 subs is better than one the MONO signal that drives those subwoofers keeps them from projecting the three dimensional images in the sub harmonics Using two 2 subwoofers allows you to cross the subs up to 150Hz sound quality imaging and staging In some applications you might have small fr
20. onse Adjust the crossover FREQ control to get the smoothest response Step 4 Use the phase control to make the response even smoother It has its biggest effect at the crossover frequency You can iterate between the crossover and the phase controls Keep your hands off the VOLUME control as it was correctly set in Step 2 Step 5 Listen to the subwoofer Resist all temptation to turn up the VOLUME control Play something with really deep bass to confirm that your subwoofer is working 14 MiniMe P8v2 P8Wvz Manual Use the following charts to record more desirable data from test results gt Om SUB LFE C l xX 50Hz 160Hz 0 180 NS A Cm SUB LFE L MIN MAX 50Hz 160Hz co t N 5 r Cm SUB LFE S MIN MAX 50Hz 160Hz _ J lt P Cm o SUB LFE S MIN MAX 50Hz 160Hz pi _ oo lt s I Cm SUB LFE k MIN MAX 50Hz 160Hz AEN oo S Earthquake Sound Corp 800 576 7944 www earthquakesound com MiniMe P8v2 P8Wv2 Subwoofer Dimensions and Specifications 11 1 2 290mm With Grille Enclosure Type Amplifier Power Drivers Frequency Response Crossover Frequency Signal Sensin
21. ont speakers or planar speakers The two front subwoofer system is an excellent solution to planar speakers low frequency response early roll off from 150Hz on down When placing these subwoofers in a close proximity to the stereo satellite the subs will enhance low frequency extension It will be better to have a stereo subwoofer to help in the lower bass notes and their placement Suppose you have only one 1 subwoofer in the room and it is placed on the right side of the room If a bass guitar player was standing on the left side of the stage and played an EE note 42Hz then the sub will also respond to that from the right side of the room and completely destroy the stage You will see illustrations showing the two 2 different suggested setups In each of them note the breakaway and the image separation represented by the black and gray arrows The black arrows represent the I gt subharmonic frequencies The gray arrows represent the lows mids and highs as they follow the action The best response is achieved when the subharmonic frequencies are dynamically synchronized with the rest or the audio system the black and gray arrows are identical single Subwoofer Setup This is aGOOD setup The subharmonic frequencies black arrow always move towards the sub in the single sub setup while the lows mids and highs gray arrow follow the action Specifications are subject to change without notice Vv Y A
22. per grounding safe amp Proper handling The MiniMe P8v2 P8Wv2 subwoofer is considerably light weight and easy to maneuver However we encourage you to take precaution when unpacking the unit to prevent any possible damage to your MiniMe P8v2 P8Wvz We further suggest the following e Do not apply pressure or push against the face of the speaker as this will cause irrepairable damage to the cone and suspension e When carrying the MiniMe P8v2 P8Wv2 make sure that the speakers grilles are away from your chest eliminating the chance of pushing against the face of the speaker e Do not drop the MiniMe P8v2 P8Wvz or subject it to sudden shocks This will damage the external finish and weaken the enclosure creating air leaks e Avoid exposing the MiniMe P8v2 P8Wvz2 to moisture Water will damage the structure as well as the amplifier and speakers e Cleaning the MiniMe P8v2 P8Wvz2 is best done using soft cloth If needed use mild detergent with water Like any other electrical unit always unplug the unit before cleaning it This triangle which appears on your component alerts you to the presence of uninsulated dangerous voltage inside the enclosure voltage that may be sufficient to constitute a risk of shock DO NOT OPEN Specifications are subject to change without notice RISK OF ELECTRIC SHOCK Unpacking the MiniMe P8v2 P8Wv2 e Keep the original carton and packing materials for future shipment or storage
23. sive radiator with patented SLAPS Symmetrically Loaded Audio Passive System Technology With a ported design and piano gloss enclosure the MiniMe P8v2 P8Wvz subwoofer delivers phenomenal bass Designed in the USA the MiniMe P8v2 P8Wv2 subwoofer meets and exceeds all industry standards of performance and quality With uncompromised World Class performance and superior technology the MiniMe P8v2 P8Wvz2 subwoofer embodies both power and elegance What Makes a MiniMe Digital Class D Amplifier SLAPS Symetrically Loaded Audio Passive System The MiniMe P8v2 P8Wv2 amplifier utilizes the advanced class D circuitry with over 90 efficiency allowing it to continuously perform without getting hot Earthquake s own patented SLAPS passive radiator technology dramatically increases the subwoofer s efficiency and capability for ultra low frequency reproduction The unique design of the SLAPS employs dual identical Suspensions The 320 Watt peak power amplifier is fully equipped with 50 160Hz frequency adjustment control 0 180 phase adjustment low level RCA input auto signal sensing as well as high level speaker inputs and outputs Premium Long Throw Drivers The active driver installed in every MiniMe P8v2 P8Wvz is specifically designed for accurate reproduction of bass and sub bass frequencies Built with TCT Turbine Cooled Transducer Technology stitched tensile leads anti wobble con
24. ssover frequency should be set at max value Low Level Setup Dual Sub For a more realistic sound stage and greater theater experience we suggest having two 2 subwoofers and running them in stereo Using a Y RCA cable connect the SUB PRE OUT 1 of the receiver to the LOW LEVEL INPUT of the left side MiniMe P8v2 P8Wv2 Using another Y RCA cable connect the SUB PRE OUT 1 of the receiver to the LOW LEVEL INPUT of the right side MiniMe P8v2 P8Wvz In case the subwoofers become out of phase with the main front speakers adjust the phase shift to correct the problem Note that maximum bass is only achieved when the sub is in phase with the speakers in your system 10 MiniMe FF8v2 Manual back of typical processor receiver FRONT SURROUNDSUR BACK SUB CENTER NOTE DO NOT USE HIGH LEVEL AND LOW LEVEL INPUTS AT THE SAME TIME back of typical Gr processor receiver Earthquake Sound Corp 800 576 7944 www earthquakesound com High Level Setup Single Sub The MiniMe P8v2 P8Wv2 has a high speaker level input connection This setup is a solution when you experience excessive noise or hum with the line level input Simply connect the speaker wire up to 16 gauge from the receiver s SPEAKER OUTPUTS to the MiniMe P8v2 P8Wv2 s SPEAKER Remember to always connect red to red and black to black when making connections between a receiver processor to the subwoofer
25. venue PAM AGUAA D levels exceeding 85dB can be dangerous with constant exposure set your audio Hayward CA 94545 system to a comfortable loudness level United States of America Earthquake Sound Corporation does not Tel 510 732 1000 assume liability for damages resulting from the direct use of Earthquake Sound audio product s and urges users to play volume at moderate levels Fax 510 732 1095 2014 Earthquake Sound Corporation All rights reserved This document should not be construed as a commitment on the part of Earthquake Sound Corporation The information is subject to change without notice Earthquake Sound Corporation assumes no responsibility for errors that may appear within this document 2 MiniMe P8v2 P8Wv2 Manual Earthquake Sound Corp 800 576 7944 www earthquakesound com About Earthquake Sound Corporation For over 28 years Earthquake Sound has been producing a variety of high quality audio products that have impressed audiophile communities around the world It all started in 1984 when Joseph Sahyoun a music freak and Aerospace Engineer unhappy with the existing loud speaker technology and performance decided to put his advance engineering knowledge to use He pushed technological boundaries to the limit to create the kind of subwoofer he could live with Earthquake quickly created a name for itself in the car audio industry and became well known for its powerful subwoofers and amplifiers In 1997 us
Download Pdf Manuals
Related Search