Home

SEKURE DGP2-648 Installation manual

1. Event Group Event Feature Group Feature Start End gm 000 n Touch Voice Module Disarming 008 008 daa Special Disarming cont d 255 Any Special Disarming Event Not Used Not Used 023 Zone Bypassed 001 to 096 001 to 096 024 Zone in Alarm 001 to 096 001 to 096 F 000 025 Fire Alarm 255 any zone Zone Numbers 001 to 096 001 to 096 026 Zone Alarm Restore 001 to 096 001 to 096 027 Fire Alarm Restore 001 to 096 001 to 096 000 User Codes 001 to 255 001 to 255 001 to 255 001 User Codes 256 to 511 000 to 255 000 to 255 028 Early to Disarm by User 002 User Codes 512 to 767 000 to 255 000 to 255 003 User Codes 768 to 999 000 to 231 000 to 231 255 Any User Code Not Used Not Used 000 User Codes 001 to 255 001 to 255 001 to 255 001 User Codes 256 to 511 000 to 255 000 to 255 029 Late to Disarm by User 002 User Codes 512 to 767 000 to 255 000 to 255 003 User Codes 768 to 999 000 to 231 000 to 231 255 Any User Code Not Used Not Used Emergency Panic keys 1 amp 3 000 000 Medical Panic keys 4 amp 6 001 001 000 Fire Panic keys 7 amp 9 002 002 030 Special Alarm Recent Closing 003 003 Police Code 004 004 Zone Shutdown 005 005 255 Any Special Alarm Event Not Used Not Used 000 User Codes 001 to 255 001 to 255 001 to 255 001 User Codes 256 to 511 000 to 255 000 to 255 031 Duress Alarm by User 002 User Codes 512 to 767 000 to 255 00
2. Dialing sequence for Tampers and Tamper Restores Partition 1 3129 Partition 3 3329 Partition 5 3529 Partition 7 3729 Partition 2 3229 Partition 4 3429 Partition 6 3629 Partition 8 3829 Default only option 1 enabled Option Call Option Call select one only 1 Telephone Number 1 5 Backup on Number 1 2 Telephone Number 2 6 Backup on Number 2 DIGIPLEXNE CONTROL PANEL 27 3 Telephone Number 3 7 Backup on Number 3 4 Telephone Number 4 8 Backup on Number 4 8 8 1 Maximum Dialing Attempts SECTION 3056 Default 008 The number 001 to 255 000 8 attempts programmed into section 3056 determines how many times the control panel will dial the same Monitoring Station Telephone Number before proceeding to the next number Also refer to section 8 8 3 UL Note For UL Listed systems the maximum dialing attempts must be set to 5 to 10 attempts between the DGP NE96 s two telephone lines 8 8 2 Delay Between Dialing Attempts SECTION 3054 Default 020 This delay will determine the amount of time the control panel will wait between dialing attempts This delay can be set from 001 to 127 seconds 8 8 3 Alternate Dialing Option SECTION 3037 OPTION 6 Default disabled With option 6 enabled in section 3037 the control panel dials the selected backup telephone n
3. Section Input Section 0961 Input 01 0973 Input 13 ATZ of Input 01 0962 Input 02 0974 Input 14 ATZ of Input 02 0963 Input 03 0975 Input 15 ATZ of Input 03 0964 Input 04 0976 Input 16 ATZ of Input 04 0965 Input 05 0977 Input 17 ATZ of Input 05 0966 Input 06 0978 Input 18 ATZ of Input 06 0967 Input 07 0979 Input 19 ATZ of Input 07 0968 Input 08 0980 Input 20 ATZ of Input 08 Set the Input Speeds for the optional 4 Zone Hardwire Module DGP2 ZX4 Section Input 0969 Input 09 DGP2 ZX4 Input 01 0970 Input 10 DGP2 ZX4 Input 02 0971 Input 11 DGP2 ZX4 Input 03 0972 Input 12 DGP2 ZX4 Input 04 0981 Input 21 ATZ of DGP2 ZX4 Input 01 0982 Input 22 ATZ of DGP2 ZX4 Input 02 0983 Input 23 ATZ of DGP2 ZX4 Input 03 0984 Input 24 ATZ of DGP2 ZX4 Input 04 4 7 EOL ON HARDWIRE ZONES SECTION 3033 OPTION 7 Default disabled If detection devices connected to hardwired input terminals use 1kQ end of line resistors enable option 7 in section 3033 For details on using EOL resistors refer to Addressable Zone Connections on page 7 and Double Zone Connections on page 8 4 8 KEYPAD NUMBERING SECTIONS 2801 To 2832 Keypad Numbering is only used to identify the keypad in the event buffer When Keypad Numbering is not used the event buffer will then display any events pe
4. Partition 2 3203 Partition 4 3403 Partition 6 3603 Partition 8 3803 Option Day Option Day 1 Sunday S 5 Thursday T 2 Monday M 6 Friday F 3 Tuesday T 7 Saturday S 4 Wednesday W 8 Holidays H 8 3 3 Arming Disarming Schedule Tolerance Window Default 000 The Arming Disarming Schedule Tolerance Window Section Account Number Peel See Ha 1 3061 Account Number 1 Partition 1 CSTN 1 3062 Account Number 2 Partition 2 CSTN2 3063 Account Number 3 Partition 3 CSTN 3 3064 Account Number 4 Partition 4 CSTN 4 8065 Account Number 5 Partition 5 N A 3066 Account Number 6 Partition 6 N A 3067 Account Number 7 Partition 7 N A 3068 Account Number 8 Partition 8 N A lengthens the partition s Arming Disarming Schedule for some users User Access Codes with Add Tolerance Windows to Schedules enabled refer to 26 REFERENCE amp INSTALLATION MANUAL For example if the Account Number Transmission see section 8 6 on page 27 corresponds to the partition and a zone generates an alarm in Partition 1 the control panel will send the Partition 1 Account Number defined in section 3061 followed by the report code numbers Account numbers that use other reporting formats do not support the 0 lt 0 digit Enter the STAY lt A digit in its place When using the SIA Format and t
5. 11 3 INSTALLER CODE Lock SECTION 3001 Default 000 Enter 147 into section 3001 to lock all programming When 147 is programmed performing a hardware reset as described in section 11 1 will not affect the current panel settings To remove the Installer Lock enter 000 into section 3001 11 4 DAYLIGHT SAVINGS TIME SECTION 3030 OPTION 3 Default enabled When option 3 is enabled the control panel adjusts the system s clock time for daylight saving changes At 2 00AM on the first Sunday of a full weekend in April the control panel will add one hour to the programmed time clock At 2 00AM on the last Sunday of a full weekend in October the control panel will subtract one hour from the time clock 32 REFERENCE amp INSTALLATION MANUAL 11 5 BATTERY CHARGE CURRENT SECTION 3030 OPTION 5 When option 5 is enabled the battery s charge current is 700mA min 40VA transformer When option 5 is disabled the charge current is 350mA Depending on the battery s capacity enable or disable the option Option Feature 5 ON 700mA 5 OFF 350mA default 11 6 COMBUS SPEED SECTION 3030 OPTION 8 This feature sets the communication speed between the control panel and the modules to either Normal or High speed In large installations with many modules where a quicker communication response time is needed set the speed to High If you are experiencing communication troubles se
6. DGP2 2X4 Same ground connections as the panel but do not connect the DGP2 ZX4 s ground directly to the control panel s ground For the hardwire connections see Single Zone and Double Zone Connections ZONE EXPANDER YOLIINNOD MaONVdXa Reset Jumper WARNING Do not connect a DGP2 TM1 Time Module to the mem key tm1 connector Connecting a DGP2 TM1 will create time errors within the panel and features that use the control panel s internal clock ex Auto arming will not function correctly Connecting the Earth Connections AWG 14 single conductor solid copper wire To metallic enclosure To provide maximum lightning protection we strongly recommend having separate earth connections for the dialer and zone ground terminals ssooske KEYPAD 71 PGM RED BLK GRN YEL MR3 optional UL Door Contact VEL if EOL is enabled in the control panel The combus supports a maximum of 127 modules Although COM N C N O external power supplies can be used to provide power to modules connected far from the control panel the total distance of all runs of wire combined cannot exceed 914m 3000ft For example if ten runs of wire measuring 305m 1000ft each are connected to the control panel the total distance would be 3048m 10 000ft which exceeds the System s capacity WARNING Before adding any module to the control panel make sure you shutdown the control panel by removing AC
7. 1 3A8 System shutdown 1 3A5 System reset 1 6A2 Periodic test report 1 412 Successful download access 1 627 Program mode Entry 1 628 Program mode Exit Default SIA Report Code for sections 4032 to 4037 AR AC Restoral YR System Battery Restoral YQ Power Supply restored YH Bell Restored YH Bell Restored JT Time Changed FJ Fire Trouble Restore ET Expansion Trouble TA Tamper Alarm YF Parameter Checksum Fail LT Phone Line trouble YC Communication Fails VT Printer Trouble AT AC Trouble YT System Battery Trouble YP Power Supply Trouble ER Expansion Restoral TR Tamper Restoral YG Parameter Changed LR Phone Line Restoral VR Printer Restore AR AC Restoral YR System Battery Restoral YQ Power Supply Restored YC Communication Fails XT Transmitter Battery Trouble XR Transmitter Battery Restoral US Untype Zone Supervision UR Untyped Zone Restoral RR Power Up YW Watchdog Reset TX Test Report RS Remote Program Success LB Local Program LS Local Program Success DIGIPLEXNE CONTROL PANEL 53 APPENDIX 3 CONTACT ID REPORT CODE LIST Prog S Prog v Prog CID Reporting Code CID Reporting Code CID Reporting Code MED A A 100 Y V B 900 amp HEMO A 410 100 Medical Alarm 101 Personal Emergency 102 Fail to Report In FIRE ALARMS 110 110 Fire Alarm 111 Smoke 112 Combustion 113 Water Flow 114 Heat
8. 28 CHIME ZONE iv were E 43 Auto Test Report Period eee eee 28 GleanMe RE RE meae d teer e Eee pai eie tute deese den n ve 9 Auto Trouble Shutdown csse 34 Clear Bell Current Limit Trouble esee nano 44 Auto Zone Shutdown eke RR ee ER a AR Re eee a mne 14 Clock Compensation Value sss 34 Auto Arming Clock Loss No Movement in Z o d e a eee Fem e d Meda aT 19 Access during Clock LOSS sss 40 No Movement Timer EEN 19 Closing Delinquency Time 29 uu soreness aa E 18 Gode ACCeSS Rg adora x dde deed ene Ue a n eed d AE 39 DIGIPLEXNE CONTROL PANEL 55 Code Follows Schedule ieke ee ER ee ER Re RA Re ee 37 EOL Zones ie vial ets ot A ee usd 15 Codes ESL CleanMeTM Installation sees ie ee ee ese 9 Special Alarm Report Codes ee ee Ee EE ER ER e 25 Event Buffer Special Arming Report Code 24 Log Door Forced Open Restore In Event Buffer 40 Special Disarming Report Codes n 25 Log Door Left Open Restore In Event Buffer 40 System Trouble Codes ENEE 25 Log Request For Exit In Event Buffer 40 System Trouble Restore Codes ie ee eee 25 Est A A EC 31 Compensation Value Clock sse 34 Event Record Display ee conocio 43 Connecting the Bus in Noisy Environments ek eek ee ek ee ee 9 Everyday arming See Regular Arming Connections EXIBDBays Seek e EE 19 Advanced Technology Zone TZ 13 l Bell siren Output cete 4 Exit D
9. OFF OFF Master disabled Access Codos User can create new User Access Codes with ON OFF Master enabled default options only can program PINs and User Labels User can create or modify User Access Codes with the same partition assignment and the second set of brackets enter the two digit Primary Schedule number 00 to 15 00 unrestricted to be assigned to that User Access Code 12 7 3 Access Control Options SECTIONS 1002 To 1999 Access OPTION SCREEN OPTIONS 1 To 8 The Access Control Options define how each Access Card can arm or disarm the partitions To arm the partition s assigned to the door a valid card is presented to the reader twice within approximately 5 seconds while the door remains closed For the card to be valid it must be presented during its assigned Schedule within its assigned Access Level and be assigned to the keypad s assigned partitions depending on the Door User can Force Arm assigned partitions see 7 EEN section 15 4 Option 8 ON User can access all its assigned partitions regardless of the keypad s partition assignment Option 8 OFF User can only access the partitions assigned to both itself and the keypad User Menu Access 8 12 6 PARTITION ASSIGNMENT SECTIONS 1002 TO 1999 AssIGN AREA SCREEN OPTIONS 1 TO 8 Each of the 998 User Access Codes can be assigned to one or more partitions Users can only arm disarm and view
10. Stay Armed Instant Armed Strobe Alarm Silent Alarm Audible Alarm Fire Alarm Ready Exit Delay Entry Delay System in Trouble Alarm in Memory Zones Bypassed Bypass Master Installer Programming Keypad Lockout Intellizone Delay Engaged see NOTE 4 on page 50 000 009 Fire Delay Engaged 001 001 Auto Arm 002 002 066 Status 3 See NOTE 1 Arming with Voice Module set until 003 003 on page 50 Exit Delay finishes Tamper 004 004 Zone Low Battery 005 005 Fire Loop Trouble 006 006 Zone Supervision Trouble 007 007 Chime in Partition 1 to 4 000 to 003 System 1 to 4 900110003 Pago sus Smoke Detector Power Reset 004 004 Ground Start 005 005 Kiss Off 006 006 Telephone Ring 007 007 Bell on Partition 1 to 8 008 to 015 Partitions 1 to 8 008 t0 015 ia Fire Alarm in Partition 1 to 8 067 Special Status N A 016 to 023 Partitions 1 to 8 016 to 023 016 to 023 Open close Kiss Off in Partition 1 to 8 024 to 031 Partitions 1 to 8 02410 0an dd Keyswitch PGM Inputs 01 to 32 032 to 063 Keyswitch PGM Inputs 032 to 063 032 to 063 01 to 32 Status of Access Door 01 to 32 064 to 095 Access Doors 01 to 32 064 to 095 Donne Trouble in System 096 096 DIGIPLEXNE CONTROL PANEL 49 Event Group Feature Group Feature Start End rouble in Dialer 09 09 Trouble in Module 098 098 Trouble in Combus 099 099 Future Use
11. 115 Pull Station 116 Duct 117 Flame 118 Near Alarm PANIC ALARMS 120 120 Panic Alarm 121 Duress 122 Silent 123 Audible BURGLAR ALARMS 130 130 Burglary 131 Perimeter 132 Interior 133 24 Hour 134 Entry Exit 135 Day Night 136 Outdoor 137 Tamper 138 Near Alarm 139 Intrusion Verifier GENERAL ALARMS 140 140 General Alarm 141 Polling Loop Open 142 Polling Loop Short 143 Expansion Module Failure 144 Sensor Tamper 145 Expansion Module Tamper 24 HOUR NON BURGLARY 150 amp 160 150 24 Hour Non Burglary 151 Gas Detected 152 Refrigeration 153 Loss of Heat 154 Water Leakage 155 Foil Break 156 Day Trouble 157 Low Bottled Gas Level 158 High Temperature 159 Low Temperature 161 Loss of Air Flow FIRE SUPERVISORY 200 amp 210 200 Fire Supervisory 201 Low Water Pressure 202 Low CO2 203 Gate Valve Sensor 204 Low Water Level 205 Pump Activated 206 Pump Failure 54 REFERENCE amp INSTALLATION MANUAL ROUB 300 System Trouble 301 AC Loss 302 Low System Battery 303 RAM Checksum Bad 304 ROM Checksum Bad 305 System Reset 306 Panel Program Changed 307 Self Test Failure 308 System Shutdown 309 Battery Test Failure 310 Ground Fault SOUNDER RELAY TROUBLES 320 320 Sounder Relay 321 Bell 1 322 Bell 2 323 Alarm Relay 324 Trouble Relay 325 Reversing Relay SYSTEM PERIPHERAL TROUBLES 330 amp 340 330 System Peripheral 44 331 Polling Loop Open 45 332 Polling Loop Short 46 333 Expansion
12. 80PU 270PU 454PU OK 305m 1000ft As indicated in Table 2 on page 6 this run of wire can support 136PU Total PU on this run of wire A 40PU C 30PU 70PU lt 136PU OK An LCD Keypad 80PU can be added to the 100ft or 300ft wire in Figure 2 4 but adding an LCD Keypad to the 1000ft wire would exceed the wire s limits and cause devices to function at decreased capacity Figure 2 5 External Power Supply Connections 16 5VAC 40VA Transformer Power units required by devices connected to a power supply do not draw power from the control panel s auxiliary output Module 500ft from control panel 500ft from control panel s aux output Therefore this run max 273PU Power Supply 2000ft from control panel 500ft from power supply Therefore this run max 273PU Do not use the same transformer for the control panel and the external power supplies Do not install modules more than 3000ft 914m from the control panel 2 12 KEYPAD ZONE CONNECTIONS Every keypad except Grafica has one hardwire input terminal allowing you to connect a detector or door contact directly to the keypad For example a door contact located at the entry point of an establishment can be wired directly to the input terminal of the entry point keypad instead of back to the control panel Even with the ATZ feature enabled in the control panel only A one device can be connected to the keypad s hardwired input
13. Silent Knight Fast P Sections 0201 to 0296 2 Sections 0701 to 0732 i Sisto Sections 0801 to 0832 Sections 2001 to 2099 Delay Between Dialing Attempts Sections 2101 to 2199 Section 3054 2 3 sl Sections 3900 to 3991 Ademco Express 7 DTMF Pager Tone 6 Sections 4030 to 4037 SIA FSK Manual amp Automatic programming of report codes refer to 1 Ademco Contact ID and SIA FSK under Reporting Formats G 5 2 Auto Report Code Programmin Ademco Contact D u p 9 9 DIGIPLEXNE CONTROL PANEL 23 8 1 REPORTING ENABLED SECTION 3036 OPTION 3 Default disabled With option 3 ON in section 3036 Event Reporting is enabled When an event e g zone in alarm occurs in the system the control panel verifies if a report code was programmed in the section corresponding to the event If a report code is programmed the control panel dials the Monitoring Station telephone number defined by the Event Call Direction feature When the Monitoring Station answers the control panel transmits the system account code followed by the programmed report code 8 2 REPORT CODES A report code is a 2 digit or 1 digit hexadecimal value consisting of digits from 0 to E For a comprehensive list of the events and their relevant sections please refer to the DigiplexNE Programming Guide Only the Ademco Slow Silent Knight Sescoa and Pager Formats support 1 digit report codes When a
14. Telephone Line Connection Examples Example 1 DigiplexNE eyes N TT Y m m CNR R2 T2 RNG2TIP2 sko dau GRN RED Main line 2nd line Example 2 DigiplexNE Dialer D 1 TT R2 T2 M Main line DIGIPLEXNE CONTROL PANEL 9 Example 3 DigiplexNE Dialer Q Ti RNG1 TIP1 re T2 bai Main line 2nd line Example 4 DigiplexNE Dialer o 7 P T T T2 En ek alo olv NU Main line For TBR 21 compliance please note the following 1 The DGP NE96 can be connected to the telephone network via an RJ 11 connector 2 The Maximum Dialing Attempts cannot exceed 15 attempts page 28 2 19 BuiLT IN RTC The DigiplexNE incorporates an RTC directly on the PC board The RTC will save the DigiplexNE s internal clock when both the AC and battery power have been lost After power is lost and then restored the DigiplexNE will verify with and then retrieve the time from the RTC The control panel will verify and compare its time with the time stored in the RTC every hour If the times are different the DigiplexNE will reset its internal clock to the time saved in the RTC The RTC uses a 3V lithium battery CR2032 with a battery life of 11 years Change the battery as shown below Figure 2 11 Changing the RTC s Battery 3V Lithium Battery CR2032 Insert the battery with the positive facing up O and the negative facing down Reprogram the control panel s clock after changing the battery
15. The B key LCD keypads Keys 4 and 6 simultaneously 2 Panic 2 Grafica keypads The A key LCD keypads Keys 7 and 9 simultaneously 3 Panic 3 Grafica keypads The ch key Option Alarm Type ON Audible 4 Panict Ger Report Only 4 ON Audible 5 Panic2 Ger Report Only S ON Fire OFF Report Only REPORT ONLY The keypad emits a single Confirmation Beep and transmits the appropriate report code see section 8 2 10 AUDIBLE ALARM The control panel activates the BELL output until a user cancels the alarm with a valid User Access Code or when the Bell Cut Off Timer elapses see section 7 2 FIRE ALARM Same as audible operation except that the bell siren output will be pulsed as shown in Figure 4 4 on page 14 UL Note For UL Listed systems all emergency non medical and auxiliary panic alarms shall be report only 22 REFERENCE amp INSTALLATION MANUAL EVENT REPORTING AAA OO Aa ee Dialing Enabled Disabled Section 3036 Option 3 Y Reporting Account Numbers Y Central Station Telephone Numbers 1 to 4 32 digits Sections 3071 to 3074 Y Event Call Direction Defines to which Central Station Telephone Number each specific group of events will be reported Y Reporting Formats Section 3070 First digit CSTN 1 Second digit CSTN 2 Third digit CSTN 3 Fourth di
16. bell auxiliary and or TLM failures for the modules connected to the combus The control panel will prevent arming if the control panel detects the equivalent trouble condition occurring on a module For example if options 1 2 and 5 are ON in section 3035 the control panel prevents arming if it detects an AC or battery failure on the control panel or on a module connected to the combus 6 9 TIMED AUTO ARMING Default disabled When this option is enabled the control panel arms the selected partition every day at the time set by the Auto Arm Timer see section 6 9 1 A 60 second Exit Delay triggers before the partition arms but Auto Arming can be cancelled by entering a valid access code The Auto Arming Option sets the arming method see section 6 11 If zones are open when a partition is Auto Armed the control panel arms the partition and considers all open zones as temporarily bypassed except 24hr zones When the partition Auto Arms the control panel transmits the Auto Arming report code programmed in section 3910 Whether the partition was successfully armed or not the control panel will always transmit the Late to Close report code programmed in section 3912 Enable option 1 in the desired section Partition 1 3122 Partition 3 3322 Partition 5 3522 Partition 7 3722 Partition 2 3222 Partition 4 3422 Partition 6 3622 Partition 8 3822 6 9 1 Auto Arm Timer
17. see section 3 5 key in the module s serial number and follow the programming indicated in the DigiplexNE Modules Programming Guide To exit this mode press the CLEAR key until Normal Mode is displayed 11 15 MODULE AND LABEL BROADCAST SECTION 4004 Module Broadcast To copy the contents of the programming sections from one module to one or more of the same type key in the serial number of the source module in section 4004 enter the serial numbers of all the destination modules and press Acc if using an LCD keypad or the center action key Start if using a Grafica keypad Label Broadcast Copy the User Labels Zone Labels sections 0301 to 0396 the Door Labels sections 2301 to 2332 and the Partition Labels sections 3100 3200 3300 3400 3500 3600 3700 and 3800 to all the modules in the system that support these labels To transmit the labels in section 4004 enter the control panel s serial number From the Destination screen do not enter a serial number and press Acc if using an LCD keypad or the center action key Start if using a Grafica keypad The Module and Label Broadcast feature will only work when a A module is broadcasting its data to a module or to modules of the same type and model number For example an APR PRT1 Printer Module cannot broadcast to an APR3 PRT1 Likewise a DGP module cannot broadcast to a DGP2 module Module Broadcast Example Using an LCD keypad to pr
18. 10 SHABBAT FEATURE SECTION 3030 OPTION 4 Default disabled When option 4 is enabled detectors and keypads in the system no longer display system status through the LCD and or LEDs between noon 12 00PM Friday and midnight 12 00AM Saturday Normal operation is re instated Sunday morning at 12 00 01AM If required a user can access all the usual commands and features during the Shabbat period by pressing a key or by entering their access code also depending if and how Confidential Mode is enabled in the keypad When no actions have occurred for two minutes the Shabbat Feature will re activate During the Shabbat period the LCD keypads only display the date and time the backlight is disabled the LED indicators on modules are disabled 11 11 INSTALLER FUNCTION KEYS Press and hold the 0 key and key in the INSTALLER CODE to access the installer functions and then For LCD keypads Press the key indicated in the list below that corresponds to the function you wish to activate For Grafica keypads Press the center action key Options highlight the desired function and then press the left action key Select Keys Description TEST REPORT Sends the Test Report report code programmed ind in section 3902 to the Monitoring Station CALL WINLOAD Dials the PC telephone number programmed FORCE in section 3010 to communicate with a computer using WinLoad ANSWER WINLOAD Forces the co
19. 100 to 102 100 to 102 Time and Date Trouble 103 103 AC Failure 104 104 Battery Failure 105 105 Auxiliary Current Limit 106 106 Bell Current Limit 107 107 Bell Absent 108 108 ROM error 109 109 RAM error 110 110 Future Use 111 111 TLM 1 Trouble 112 112 Fail to Communicate 1 113 113 Fail to Communicate 2 114 114 Fail to Communicate 3 115 115 Special Status cont a Fail to Communicate 4 116 116 Fail to Communicate with PC 117 117 Future Use 118 118 Future Use 119 119 Module Tamper Trouble 120 120 Module ROM error 121 121 Module TLM error 122 122 Module Failure to Communicate 123 123 Module Printer Trouble 124 124 Module AC Failure 125 125 Module Battery Trouble 126 126 Module Auxiliary Failure 127 127 Missing Keypad 128 128 Missing Module 129 129 Future Use 130 to 132 130 to 132 Global Combus Failure 133 133 Combus Overload 134 134 Combus Fail to Communicate 135 135 Hour Minutes NOTE 1 000 Occurs in all partitions enabled in the system see section 3031 001 Partition 1 003 Partition 3 005 Partition 5 007 Partition 7 002 Partition 2 004 Partition 4 006 Partition 6 008 Partition 8 255 Occurs in at least one partition enabled in the system NOTE 2 This TLM trouble event can only be used with the DigiplexNE control panel models that have two dialers NOTE 3 This TLM tro
20. 2 and power limited fire alarm circuits shall be installed using CL3 CL3R CL3P or substitute cable permitted by the National Electrical Code ANSI NFPA 70 The control unit and keypads are intended to be programmed and installed as follows Household Fire Warning Systems US and Canada At least one model DGP2 641 keypad shall be used with the system One Paradox model MR3 UL end of line supervision relay The relay is intended to provide supervision of the smoke detector power circuit N One listed audible device rated to operate over the range of 11 4 to 12 5Vdc and rated 85db minimum is required for this application For example Wheelock model 46T 12 is compatible The bell cutoff time shall be programmed for a minimum of 4 minutes 5 minutes for Canada The fire alarm initiating circuit shall employ the listed model 2011002000 PRT end of line resistor N For Canadian systems the secure screw for the listed Class 2 transformer shall not be employed Household Grade A Burglar Alarm system Unit US and Canada N At least one listed audible device rated to operate over the range of 11 4 to 12 5Vdc and rated 85db minimum For example Wheelock model 46T 12 is compatible At least one model DGP2 641 keypad shall be used All initiating circuits shall be programmed and installed as end of line supervised Burglar alarm initiating devices shall be rated to operate over the range of 11 4 to 12 5Vdc The bell cutoff time
21. 3039 The Schedule Tolerance Window lengthens the assigned Schedule of some users User Access Codes with Add Tolerance Windows to Schedules enabled have the number of minutes programmed in 3039 added before and after their Schedule This feature can be used instead of creating Schedules for each shift and each shift s supervisor by assigning the supervisors to their respective shift s Schedule and enabling Add Tolerance Windows to Schedules on their User Access Codes Enter any value between 001 and 255 default 000 to determine Schedule Tolerance Window in minutes For example if 060 is programmed in section 3039 users with Add Tolerance Windows to Schedules enabled will have their Schedule 8 Holidays H Option Feature OR Access Door The Access Door grants access or permits arming or 1 ON disarming to users assigned to at least one of the door s partitions An OR door will arm or disarm only the partitions that it has in common with the users AND Access Door 1 OFF The Access Door grants access or permits arming only to users assigned to all the door s assigned partitions 13 11 CODE ACCESS SECTION 2251 TO 2282 OPTION 2 Code Access can allow access to an Access Door by entering a valid User Access Code and pressing the ACC key on a DGP2 641 LCD Keypad instead of using the Access Card The control panel will verify the User Access Code s validity in the same way it would verify
22. 4 closes Utility Key Event 9 N A KS Input 9 opens KS Input 5 opens Utility Key Event 10 N A KS Input 10 opens KS Input 5 closes Utility Key Event 11 N A KS Input 11 opens KS Input 6 opens Utility Key Event 12 N A KS Input 12 opens KS Input 6 closes Utility Key Event 13 N A KS Input 13 opens KS Input 7 opens Utility Key Event 14 N A KS Input 14 opens KS Input 7 closes Utility Key Event 15 N A KS Input 15 opens KS Input 8 opens Utility Key Event 16 N A KS Input 16 opens KS Input 8 closes Utility Key Event 17 N A KS Input 17 opens KS Input 9 opens Utility Key Event 18 N A KS Input 18 opens KS Input 9 closes y N A y y Utility Key Event 31 N A KS Input 31 opens KS Input 16 opens Utility Key Event 32 N A KS Input 32 opens KS Input 16 closes Utility Key Event 33 N A N A KS Input 17 opens Utility Key Event 34 N A N A KS Input 17 closes y N A N A y Utility Key Event 63 N A N A KS Input 32 opens Utility Key Event 64 N A N A KS Input 32 closes Keyswitch Refer to the Omnia Reference and Installation Manual for remote control button programming instructions DIGIPLEXNE CONTROL PANEL 51 APPENDIX 2 AUTOMATIC REPORT CODE LIST _E NAAA
23. 6 digits the control panel adds 2 digits to the end by using the first 2 digits For example if the User Access Code is 1234 and you switch to 6 digits the code will become 123412 Option Description 2 3 OFF OFF 4 digit User Access Code Default OFF ON 6 digit User Access Code ON ON Flexible User Access Code 12 3 SYSTEM MASTER CODE SECTION 1001 Default 123456 The Installer Code can change the User Code Options Partition Assignment and Access Control Options but cannot change the personal identification number PIN Each digit in the System Master Code can be any value from 0 to 9 To reset the System Master Code refer to section 11 2 on page 32 With the System Master Code a user can use any of the available arming methods with access to all partitions and can program all User Access Codes User Options Partition Assignments and Access Control Options 12 4 PRocRAMMING ACCESS CODES SECTIONS 1002 To 1999 Default all options are off The control panel supports 998 User Access Codes In sections 1002 to 1999 the Installer Code can program the User Code Options Partition Assignment and Access Control Options but cannot program the personal identification numbers PIN To program the PINs refer the users to the System Manager s Manual The System Master Code or a user with the Master feature enabled can program the User Code Options Partition Assignment Acc
24. AA lt A _ lt lt lt lt 2 2 21244 ee System Event Arming with Master Code Arming with User Code Arming with Keyswitch Auto Arming Arm with PC software Late To Close No Movement Partial arming Quick arming Disarm with Master Code Disarm with User Code Disarm with Keyswitch Disarm after alarm with Master Code Disarm after alarm with User Code Disarm after alarm with Keyswitch Cancel alarm with Master Code Cancel alarm with User Code Cancel alarm with Keyswitch Auto Arming Cancellation Disarm with PC software Disarm after an alarm with PC software Quick Disarm Zone Bypassed Zone alarm Fire alarm Zone alarm restore Fire alarm restore 24Hr Gas alarm 24Hr Heat alarm 24Hr Water alarm 24Hr Freeze alarm 24Hr Gas alarm restore 24Hr Heat alarm restore 24Hr Water alarm restore 24Hr Freeze alarm restore Police Code Panic 1 Emergency Panic 2 Medical Panic 3 Fire Recent closing Global zone shutdown Duress alarm Zone shutdown Zone tampered Zone tamper restore Keypad Lockout AC Failure Battery Failure Auxiliary supply trouble Bell output current limit Bell absent Clock lost Fire loop trouble TLM trouble restore Default Contact ID Report Code for sections 4032 to 4037 3 4A1 Close by user 3 4A1 Close b
25. AC Failure 006 006 Battery Failure 007 007 Auxiliary Failure 008 008 Any Module Trouble Restore Event Not Used Not Used Fail to Communicate on Telephone Telephone Number 001 to 004 001 to 004 Number Any telephone number Not Used Not Used 041 Low Battery on Zone 001 to 096 001 to 096 042 Zone Supervision Trouble 000 001 to 096 001 to 096 043 Low Battery on Zone Restored 255 any Zone Zona Numbers 001 to 096 001 to 096 044 Zone Supervision Trouble 001 to 096 001 to 096 Restored Power up after total power down 000 000 Software reset Watchdog 001 001 Test Report 002 002 000 Future Use 003 003 045 Special Events WinLoad In connected 004 004 WinLoad Out disconnected 005 005 Installer in programming 006 006 Installer out of programming 007 007 255 Any Special Event Not Used Not Used 000 User Codes 001 to 255 001 to 255 001 to 255 001 User Codes 256 to 511 000 to 255 000 to 255 046 Early to Arm by User 002 User Codes 512 to 767 000 to 255 000 to 255 003 User Codes 768 to 999 000 to 231 000 to 231 255 Any User Code Not Used Not Used 000 User Codes 001 to 255 001 to 255 001 to 255 001 User Codes 256 to 511 000 to 255 000 to 255 047 Late to Arm by User 002 User Codes 512 to 767 000 to 255 000 to 255 003 User Codes 768 to 999 000 to 231 000 to 231 255 Any User Code Not Used Not Used 000 Utility Key 001 to 064t 001 to 064 001 to 064 048 Utility Key 255 Any Utility Keyt Not Used Not Used 049 Request for Exit 001 to 032 001 to 032 050 Access D
26. After entering the required data press Grafica s center action key Save to save the data and advance to the next section Press the right action key Exit to revert to the preceding step or press the left action key Clear to erase the current data 3 4 1 Feature Select Programming Most of the options are programmed using the Feature Select Method For LCD Keypads Each number from 1 to 8 corresponds to a specific feature or option Set these options by turning the number corresponding to the feature ON or OFF The option is considered ON when the number appears within the brackets on the LCD keypad Turn options ON and OFF by pressing the corresponding keys on the keypad Press the keys as many times as needed to select the desired options and then press ENTER to save For Grafica Keypads Select or clear the check boxes pertaining to the options or features that you wish to enable or disable You can also set the options by pressing the corresponding keys on the keypad The feature is considered ON when its check box is selected To save the settings press the Grafica s center action key Save 3 4 2 Decimal Programming Certain sections may require the entry of a 3 digit decimal value from 000 to 255 3 4 3 Hexadecimal Programming Certain sections may require the entry of one or more Hexadecimal values from 0 to F Press For LCD Keypads 0 to 9 values 0 to 9 respectively STAY key A DISARM key D FORCE key
27. B BYP key E ARM key C MEM key F For Grafica Keypads 0 to 9 values 0 to 9 respectively A to F press the key until the desired letter appears 3 5 MODULE PROGRAMMING MODE All modules are programmed through any LCD or Grafica keypad in the system To do so enter Module Programming Mode Press and hold the 0 key Key in the INSTALLER CODE Default is 000000 Key in 8 digit SERIAL NUMBER of the module Key in 3 digit SECTION and required DATA Refer to the Module Programming Guide for details Key in section 4003 The control panel will redirect all programming to the selected module To exit the Module Programming Mode press the CLEAR key on LCD keypads or the right action key Exit on Grafica keypads as many times as needed to return to the desired screen The module s serial number can be located on the module s PC board DIGIPLEXNE CONTROL PANEL 11 ZONE PROGRAMMING All detection devices connected to the control panel keypads and zone expansion modules must be assigned to a zone and that zone must be defined as described in this section Figure 4 1 Zone Programming Press amp hold the Zone Numbering Sections 0001 to 0096 represent zones 1 to 96 respectively Enter the 8 digit SERIAL NUMBER of the addressable detection device or module that has a hardwire device connected to it a Enter the module s 3 digit IN
28. Delete at the cursor s position ARM Delete Until the Deletes all characters and spaces to the End right of the cursor and at the cursor s position DISARM Numeric or Toggles from numeric keys to alphanumeric Alphanumeric keys and vice versa see Table 7 vr Lower or Upper Toggles the case setting from lower to upper Case case and vice versa The cursor will turn into a flashing black Special square Enter the 3 digit number that MEM Characters represents the desired symbol see Table 8 on page 35 Table 11 on page 35 and Table 12 on page 35 Table 7 Numeric and Alphanumeric keys Numeric Alphanumeric Key Press key Press key Press key Press key one time one time two times three times 0 0 1 1 A B C 2 2 D E F 3 3 G H l 4 4 J K L 5 5 M N O 6 6 P Q R 7 7 S T U 8 8 V W X 9 9 Y Z Table 8 Special Characters Catalogue 129 145 161 193 y 053 069 085 181 197 213 ZRI l 038 054 070 086 102 118 134 150 N 182 198 214 HEILIGE Id HE SRDE z bil hd A T RRE J Z 1 EE TEE i ES Ges hi K T 139 185 219 x 1 170 Table 9 Hebrew Keypad Letter Assignment Siw once twice three times Pl No 3 A LS a n J RI vr RE e pu 0 0 gt mm gt a apo 2 o once twice three times four times al AE EOD B rek E 2 H JJ M H n P 6 Y o j x py wg j wu wu LR b j gt A II
29. Module Failure 47 334 Repeater Failure 48 335 Local Printer Paper Out 49 336 Local Printer Failure 4A COMMUNICATION TROUBLES 350 amp 360 350 Communication 4B 351 Telco Fault 1 4C 352 Telco Fault 2 4D 353 Long Range Radio 4E 354 Fail to Communicate AF 355 Loss of Radio Supervision 50 356 Loss of Central Polling 51 PROTECTION LOOP TROUBLES 370 370 Protection Loop 52 371 Protection Loop Open 53 372 Protection Loop short 54 373 Fire Trouble 55 SENSOR TROUBLES 380 380 Sensor Trouble 56 381 Loss of Supervision RF 57 382 Loss of Supervision RPM 58 383 Sensor Tamper 59 384 RF Transmitter Low Battery 5A OPEN CLOSE 400 400 Open Close 5B 401 Open Close by User 5C 402 Group Open Close 5D 403 Automatic Open Close 5E 404 Late to Open Close 5F 405 Deferred Open Close 60 406 Cancel 61 407 Remote Arm Disarm 62 408 Quick Arm 63 409 Keyswitch Open Close 64 Callback Request Made Success Download Access Unsuccessful Access System Shutdown Dialer Shutdown ACCESS CONTROL 420 421 422 Access Denied Access Report By User SPECIAL TROUBLES 450 amp 460 450 451 452 453 454 455 456 457 458 459 461 462 463 464 465 466 Exception Open Close Early Open Close Late Open Close Failed to Open Failed to Close Auto Arm Failed Partial Arm User Exit Error User on Premises Recent Close Wrong Code Entry Legal Code Entry Re arm after Alarm Auto Arm Time Extended Panic Alarm Reset Service On Off Premis
30. Option 4 Partition 8 3821 Option 8 6 13 ALWAYS FORCE ARM WHEN REGULAR ARMING Default Disabled When option 8 is enabled for a particular partition the system will Force Arm that partition whenever Regular or Force arming is activated Stay and Instant arming are not affected by this feature 6 15 ONE TOUCH FEATURES Default disabled The One touch Features can arm or disarm a partition access Bypass Programming or display the Event Buffer by pressing and holding a specific key for 2 seconds instead of entering an access code If the keypad is assigned to more than one partition the feature must be enabled in the corresponding partitions Select the section corresponding to the desired partition and enable or disable the desired options Partition 1 3125 Partition 3 3325 Partition 5 3525 Partition 7 3725 Partition 2 3225 Partition 4 3425 Partition 6 3625 Partition 8 3825 Option One Touch Feature One Touch Key 1 Regular Arming see section 15 1 ARM 2 Stay Arming see section 15 2 sTAY 3 Instant Arming see section 15 3 5 4 Force Arming see section 15 4 FORCE 5 Stay Instant Disarming see section 15 6 DISARM 6 Bypass Programming see section 15 7 BYP 7 Event Record Display see section 15 10 7 6 16 EXIT DELAY Default 060 The Exit Delay determines the amount of time a user ha
31. Partition 7 3722 Partition 2 3222 Partition 4 3422 Partition 6 3622 Partition 8 3822 Option Feature 5 Arming Report Schedule 6 Disarming Report Schedule 8 3 2 Arming and Disarming Report Schedules Arming and Disarming Report Schedules identify the days and times that a partition should be armed and disarmed Each partition includes an Arming Report Schedule and a Disarming Report Schedule Each schedule consists of 2 programmable time periods called Intervals that determine the time span and days when the partition should be armed or disarmed see Figure 8 2 To enable the schedules refer to section 8 3 1 Figure 8 2 Example of an Arming and a Disarming Report Schedule Section 3102 Arming Schedule partition 1 Interval 1 Start Time 16 55 End Time 17 30 Options 2 3 4 5 amp 6 Section 3103 Disarming Schedule partition 1 Interval 1 Start Time 08 50 End Time 09 10 Options 2 3 4 5 6 On Monday Tuesday Wednesday Thursday and Friday Disarming Report Schedule Arming Report Schedule Start Time End Time Start Time End Time y y 8 50 9 10 16 55 17 30 Authorized Authorized time span time span to disarm to arm A B C D A If partition is disarmed Early to Open report code sent B If partition is disarmed Late to Open report code sent C If partition is armed Early to Close report code sent D If partition is armed Late to Close report c
32. The Communicator trouble appears in the ON OFF Trouble Only Trouble Display The Communicator trouble appears in the OFF ON EE Trouble Display If the partition is armed the control panel generates an alarm The Communicator trouble appears in the ON ON Silent Alarms Trouble Display The control panel switches become Audible any triggered Silent Alarm zones or Silent panic alarms to an audible alarm 9 1 1 TLM Fail Timer SECTION 3053 Default 016 If the TLM does not detect the existence of the main telephone line for the time programmed in this section the control panel will generate the condition s defined by the TLM options see section 9 1 Enter any value between 016 and 255 value is X2 seconds into section 3053 Entering a value between 000 and 016 will set the TLM Fail Timer to 32 seconds 9 2 TONE PULSE DiALING SECTION 3036 OPTION 4 Default enabled When option 4 is enabled the control panel can dial using the tone DTMF format When option 4 is disabled the control panel uses the pulse dialing format Refer to section 9 3 for setting the pulse ratio Option Feature 4 ON Tone DTMF format 4 OFF Pulse dialing format 9 3 PULSE RATIO SECTION 3036 OPTION 5 Default enabled When using Pulse dialing see section 9 2 select one of two Pulse Ratios Although most European countries use the 1 2 pulse ratio the 1 1 5 ratio may provi
33. WARNING Danger of explosion exists if the lithium battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions 10 REFERENCE amp INSTALLATION MANUAL PROGRAMMING METHODS E TTT DigiplexNE can be programmed using the following methods 3 1 WINLOAD UPLOADING DOWNLOADING SOFTWARE We highly recommend programming the control panel with WinLoad as it greatly simplifies the process and reduces potential data errors Refer to Winload Software on page 41 for details UL Note Not verified by UL 3 2 PARADOX MEMORY KEY Nor To BE USED WITH UL LISTED SYSTEMS The Paradox Memory Key can copy the programmed contents of one control panel into as many others as needed Downloading is completed in less than 5 seconds Copy to Memory Key 1 2 Download to Control Panel 1 2 Place the Memory Key on the control panel s connector labeled MEM KEY Make sure that the write protect jumper is on Enter section 4020 to copy the control panel s contents except sections 0001 to 0096 and 0501 to 0532 to the key 4021 to copy the control panel s contents including sections 0001 to 0096 and 0501 to 0532 to the key When the keypad emits a Confirmation Beep remove the Memory Key Remove the jumper to prevent accidentally overwriting the Memory Key s contents Control panel Place the Memor
34. When Timed Auto Arming is enabled see section 6 9 the control panel will attempt to arm the system at the time set by the Auto Arm Timer For example to Auto Arm partition 2 everyday at 6 15PM enable option 1 in section 3222 Timed Auto Arming and enter 18 15 in section 3201 Enter the time when the partition should arm in the desired section Partition 1 3101 Partition 3 3301 Partition 5 3501 Partition 7 3701 Partition 2 3201 Partition 4 3401 Partition 6 3601 Partition 8 3801 6 10 No MOVEMENT AUTO ARMING Default disabled If no movement occurs in a partition for the period specified by the No Movement Timer see section 6 10 1 the control panel will automatically arm that partition The Auto Arming Option determines the arming method see section 6 11 The control panel will transmit the No Movement report code programmed in section 3913 upon arming Whether the partition was successfully armed or not the control panel will always transmit the Late to Close report code 3912 Enable option 2 in the desired section Partition 1 3123 Option 8 Partition 5 3523 Option 8 Partition 2 3223 Option 8 Partition 6 3623 Option 8 Partition 3 3323 Option 8 Partition 7 3723 Option 8 Partition 4 3423 Option 8 Partition 8 3823 Option 8 6 14 FOLLOW ZONE SWITCHES TO ENTRY DELAY 2 Default enabled When opti
35. and then press the center action key Ok 6 Use the scroll keys to scroll through the events 15 11 SCROLL RESTART LCD KEYPAD ONLY The keypad scrolls through the status of its assigned partitions Press the CLEAR key at any time to return to the beginning of the sequence 15 12 TROUBLE DISPLAY When the system experiences problems or is tampered with the Trouble Display appears on the LCD screen Keypads will only display troubles that occur in their assigned partition s Potential troubles have been sorted into eight groups The Group headings are listed below with a brief explanation of the potential troubles sorted within each group To view To view the Trouble Display on LCD or LED Keypads Step 1 Press the TRBL key Step 2 For LEDs Press the Numerical Symbol corresponding to the Group heading to view the specific trouble For LCDs Press the number representing the trouble and press the A and V keys to view the specific trouble To view the Trouble Display on Grafica Keypads Step 1 Enter your ACCESS CODE Step 2 Using the scroll keys highlight Trouble and then press the center action key Ok The trouble s will appear by Trouble Group DIGIPLEXNE CONTROL PANEL 43 Step 3 If more than one Trouble Group appears highlight the desired group before pressing the center action key View to view the specific trouble Trouble Description GROUP 1 SYSTEM Power failure detected The system i
36. arm partition 1 when no movement occurs for 4 hours enable option 2 in section 3122 No Movement Auto Arm for partition 1 and enter 016 16 x 15min 240min 4 hours in section 3107 Enter the time period 001 to 255 x 15 minutes 000 disabled when the partition should arm in the desired section Partition 1 3107 Partition 3 3307 Partition 5 3507 Partition 7 3707 Partition 2 3207 Partition 4 3407 Partition 6 3607 Partition 8 3807 6 11 AUTO ARMING OPTIONS Default disabled When using the Auto Arming Features see section 6 9 and section 6 10 the control panel can Force Arm see section 15 4 or Stay Arm see section 15 2 the partitions To Auto Arm using Stay Arming enable option 3 in the desired section Partition 1 3122 Partition 3 3322 Partition 5 3522 Partition 7 3722 Partition 2 3222 Partition 4 3422 Partition 6 3622 Partition 8 3822 6 12 SWITCH TO STAY ARMING If no Entry Delay zones are opened and closed during the Exit Delay after Regular Arming a partition the control panel can switch from Regular Arming to Stay Arming Enable the option in the desired section Partition 1 3121 Option 1 Partition 5 3521 Option 5 Partition 2 3221 Option 2 Partition 6 3621 Option 6 Partition 3 3321 Option 3 Partition 7 3721 Option 7 Partition 4 3421
37. as input 4 255 Zone Definitions Disabled Default 8 24Hr Gas Entry Delay 1 9 24Hr Heat Entry Delay 2 A 24Hr Water Follow Instant 24Hr Buzzer 24Hr Burglary 24Hr Hold up E Stay Delay 1 B 24Hr Freeze C Delayed 24Hr Fire D Standard 24Hr Fire F Stay Delay 2 0 key E 1 tr gt Key in the porci bet A INSTALLER CODE l 5 l 6 l 7 ER l Key in 4 digit I SECTION Select one only 2 Zone Partition Assignment 1 Zone Assigned to Partition 1 Default Zone Assigned to Partition 2 Zone Assigned to Partition 3 Zone Assigned to Partition 4 Zone Assigned to Partition 5 Zone Assigned to Partition 6 Zone Assigned to Partition 7 Zone Assigned to Partition 8 I l l 3 l 4 EDE l I ss l 6 l 7 l l 8 a l Select one only i 1 3 4 5 Select one off or more off on on 7 8 Zone Options Auto Zone Shutdown 2 Bypass Zone Default Stay Zone Force Zone 6 Zone Alarm Type off Audible Alarm steady on Audible Alarm pulsed off Silent Alarm on Generates only a report Intellizone Delay before transmission Figure 4 2 Zone Numbering Hardwired Keypad SN 1A000 Control Panel SN 020000A2 Input Terminals Hardwired Device B Detector A Hardwired Device A Hardwired Device B Hardwired Device C 1 2 3 4 5 6 7 8 L APR3 ZX8 Module SN 34000041 Input Terminals 1 2 3 4 5 6 7 8 Z
38. as required Option Until the Clock is reset access can be granted to 8 ON The System Master Code or User Access Codes with Full Master or Schedule 00 enabled 8 OFF All users regardless of their programmed Schedules 13 17 BuRGLAR ALARM ON FORCED DOOR OR DOOR LEFT OPEN SECTION 3038 OPTION 5 FoRCED DOOR SECTION 3038 OPTION 7 DOOR LEFT OPEN Default disabled When option 5 and or 7 is enabled and an Access Door is forced open or left open it can send a signal to the control panel to trigger the burglar alarm and to report to the Monitoring Station The burglar alarm is generated instantly regardless of the zone s definition i e entry delay is ignored Also see Log Door Forced Open Restore In Event Buffer on page 40 and see Log Door Left Open Restore In Event Buffer on page 40 For these features to function the following must be done Install a door contact and connect it to the door s Access Control Module Assign the door s Access Control Module to a zone see Zone Programming on page 12 Enable option 5 in section 3038 Burglar Alarm on Forced Door Enable option 7 in section 3038 Burglar Alarm on Door Left Open 40 REFERENCE amp INSTALLATION MANUAL 13 18 LOGGING ACCESS CONTROL EVENTS 13 18 1 Log Request For Exit In Event Buffer SECTION 3038 OPTION 2 Default disabled When a Request for Exit REX device registers movement at the door a REX
39. closed to arm the system The system can also be Regular Armed by using a One touch Feature see section 6 15 or a Keyswitch see section 5 4 3 All users are able to Regular Arm the partition s assigned to their User Access Codes Refer to How to Arm on page 42 for information on how to Regular Arm the system 15 2 STAY ARMING Stay Arming partially arms the partition to permit the user to remain in the partition Stay Zones see section 4 5 3 will not arm when Stay Arming Partitions can also be armed by the Stay Arm One touch Feature see section 6 15 or a Keyswitch see section 5 4 4 Only User Access Codes with the Stay and Instant Arm option enabled can Stay Arm a partition For example arm the doors and windows without arming the motion detectors Refer to How to Arm on page 42 for information on how to Stay Arm the system 15 2 1 Stay Arming with Delay Stay Arming with Delay functions like Stay Arming except armed zones are programmed with an Entry Delay Timer see section 4 3 14 If a zone is triggered the delay starts allowing the user time to disarm the partition s 15 3 INSTANT ARMING Similar to Stay Arming Instant Arming partially arms the partition to permit the user to remain in the partition but all Delay zones become Instant zones Partitions can also be armed by the Instant One touch Feature see section 6 15 or a Keyswitch see section 5 4 6 Only User Access Codes with the Stay and Instant Arm option enab
40. immediately generates an alarm Instant zones are commonly used for windows patio doors skylights and other perimeter type zones 4 3 5 24Hr Buzzer Zones SECTIONS 0101 To 0196 FIRST DIGIT 5 Whenever a 24Hr Buzzer zone opens whether the zone is armed or disarmed the control panel activates the keypad buzzer to indicate that the zone was breached The control panel will report the alarm but will not enable the bell siren output Enter any valid access code on the keypad to stop the buzzer The keypads must be assigned to the same partition as the 24Hr Buzzer zone or the buzzer will not activate UL Note Not to be used for perimeter protection 4 3 6 24Hr Burglary Zones SECTIONS 0101 To 0196 FIRST DIGIT 6 When a 24Hr Burglary zone opens whether the system is armed or disarmed the control panel will immediately generate a burglary alarm 4 3 7 24Hr Hold up Zones SECTIONS 0101 To 0196 FIRST DIGIT 7 When a 24Hr Hold up zone opens whether it is armed or disarmed the control panel will immediately generate an alarm The SIA FSK reporting format includes specific codes to identify the alarm as a Hold up Alarm 4 3 8 24Hr Gas Zones SECTIONS 0101 To 0196 FIRST DIGIT 8 When a 24Hr Gas zone opens whether it is armed or disarmed the control panel will immediately generate an alarm The SIA FSK reporting format includes specific codes to identify the alarm as a Gas Alarm 4 3 9 24Hr Heat Zones SECTI
41. is connected Sections 0601 to 0632 represent keyswitches 1 to 32 respectively y Keyswitch Definition Keyswitch Definitions 0 Disabled default 1 Momentary Keyswitch 2 Maintained Keyswitch 3 Generates a Utility Key Event on Open 4 Generates a Utility Key Event on Open amp Close Keyswitch Partition Assignment bed one 0 Not assigned to partition s default ony 1 Assigned to partition 1 2 Assigned to partition 2 3 Assigned to partition 3 First Digit 4 Assigned to partition 4 5 Assigned to partition 5 6 Assigned to partition 6 7 Assigned to partition 7 8 Assigned to partition 8 Select one I only Keyswitch Options Keyswitch Partition Default All OFF Assignment 1 to 3 Future Use Second Digit 4 Stay Instant Disarm 5 Arm Only d 6 Stay Arming Keyswitch Options Set 7 Force Arming Feature Select options M 8 Instant Arming Select one only if all are OFF defaults to regular arming Press ENTER 5 1 KEYSWITCH NUMBERING SECTIONS 0501 To 0532 Keyswitch Numbering allows you to assign any hardwired input in the System to any of the 32 keyswitch zones in the control panel It identifies where the keyswitch is connected and which keyswitch zone is assigned to the keyswitch see Figure 5 2 Figure 5 2 Example of Keyswitch Numbering Control Panel SN 020000A2 C
42. number of different reporting formats but each of the four Monitoring Station Phone Numbers see section 8 4 should be programmed with the same reporting format unless they are combined with a Pager format The first digit entered into section 3070 represents the reporting format see Table 5 used to communicate with Monitoring Station telephone number 1 the second digit represents telephone number 2 etc Compatible Digital Alarm Communication Receivers DACRs Sur Gard DRL2A Ademco 685 Osborne Hoffman Quick Alert II Table 5 Reporting Formats 0 Ademco slow 1400Hz 1900Hz 10BPS 4 Contact ID Pager 1 Silent Knight fast 1400Hz 1900Hz 20BPS 5 Ademco Contact ID 2 Sescoa 2300Hz 1800Hz 20BPS 6 SIA FSK 3 Ademco Express DTMF 4 2 7 Pager UL Note Installer must verify the compatibility with of the DACR Use listed compatible DACRs 8 7 1 Standard Pulse Formats The control panel can use the Ademco slow Silent Knight fast and Sescoa standard pulse reporting formats see Table 5 8 7 2 Ademco Express The Ademco Express is a high speed reporting format that communicates 2 digit 00 to FF report codes Unlike other Ademco formats the Ademco Express does not use the Contact ID Report Codes 8 7 3 Contact ID Pager Using this format the control panel will transmit a Contact ID report instead of a user generated numerical code to a pager The Contact ID report code will come fro
43. rights reserved PosiPIN is a trademark or registered trademark of Position Technology Inc and its affiliates in Canada the United States and or other countries All rights reserved P A RA D O Xx SECURITY SYSTEMS 780 Industriel Blvd Saint Eustache Qu bec J7R 5V3 Canada Tel 450 491 7444 Fax 450 491 2509 www paradox ca Printed in Canada 01 2004 DGPNE96 EIO7
44. section Partition 1 3105 Partition 3 3305 Partition 5 3505 Partition 7 3705 Partition 2 3205 Partition 4 3405 Partition 6 3605 Partition 8 3805 6 20 MAXIMUM BYPASS ENTRIES Default 000 The Maximum Bypass Entries feature limits the number of zones that can be bypassed in each partition For example program section 3115 with 010 When in Bypass Programming see section 15 7 the control panel will not let the user bypass more than 10 zones in partition 1 Enter any value between 001 and 096 000 no limit Default 000 Program the duration of the keypad lockout from 001 to 255 minutes into the desired section Programming 000 into these sections will not lockout the keypad the control panel will transmit the Keypad Lockout report code programmed in section 3937 Partition 1 3115 Partition 3 3315 Partition 5 3515 Partition 7 3715 Partition 2 3215 Partition 4 3415 Partition 6 3615 Partition 8 3815 Partition 1 3106 Partition 3 3306 Partition 5 3506 Partition 7 3706 6 18 BELL SQUAWK The control panel can activate the bell output briefly causing the bell or siren to squawk to alert users that a partition is being armed disarmed or that an Entry or Exit Delay was triggered Enable or disable the desired option off disabled Partition 2 3206 Partition 4 3406 Parti
45. shall be programmed for a minimum of 4 minutes The maximum entry delay shall not exceed 60 seconds The maximum exit delay shall not exceed 45 seconds N For Canadian systems the secure screw for the listed Class 2 transformer shall not be employed DIGIPLEXNE CONTROL PANEL 59 Grade B Central Station Level 0 Same as Household Grade A Burglar alarm system unit except The ringback feature shall be enabled section 3037 option 5 page 30 The model AB12M Bell and Bell Housing manufactured by ADEMCO shall be employed Bell cutoff time shall be programmed for a minimum of 15 minutes 30 minutes for Canada The Auto Test Report setting must be programmed to send a test transmission to the central station at least once every 24 hours section 3037 options 3 and 4 on page 28 and section 3041 on page 28 N Openings and closings must be reported to the central station Report codes shall be enabled Model 278 0000 035 attack resistant enclosure must be employed Grade C Central Station Level 0 Same as Grade B Central Station except the Grade A Bell housing may not be employed Grade A Local Alarm Units Level 0 Same as Grade B Central Station except Bell test must be enabled Police Station Connect with Basic Line Security Level 0 Same as Grade B Central Station except Openings and closings may not be reported to the central station Access Control System At least one model DGP2 641AC keypad sh
46. specific event occurs the control panel will send the programmed report code to the Monitoring Station The method of report code transmission is defined by the following two items Reporting Formats see section 8 7 and Event Call Direction see section 8 8 These two items define how and where the report codes are transmitted If you are using the Ademco CID or SIA formats an Auto Report Code Programming feature is available see section 8 15 The following sub sections provide a brief description of the events that the control panel can report 8 2 1 Zone Alarm and Alarm Restore Report Codes SECTIONS 0201 To 0296 FIRST AND SECOND BRACKETS A report code can be programmed for each of the 96 available zones Each section from 0201 to 0296 corresponds to a zone from 01 to 96 The first set of 2 digits in the sections refer to the Alarm Report Codes that can be sent to the Monitoring Station to identify which zones generated an alarm The second set of 2 digits in the sections refer to the Alarm Restore Report Codes that can be sent to the Monitoring Station when a zone closes or once the bell has cut off after generating an alarm see section 7 2 Also refer to Zone Restore Report Options in section 8 14 8 2 2 Tamper and Tamper Restore Report Codes SECTIONS 0201 TO 0296 THIRD AND FOURTH BRACKETS A report code can be programmed for each of the 96 available zones Each section from 0201 to 0296 corresponds to a zone from 01
47. terminal Tamper is not recognized on keypad zones The keypad zone follows the control panel s EOL definition A device connected to the keypad s input terminal must be assigned to a zone in the control panel and the zone s parameters must be defined see Zone Programming on page 12 The keypad communicates the status of the zone to the control panel via the combus The detection device is connected as shown in Figure 2 3 on page 5 2 13 ADDRESSABLE ZONE CONNECTIONS The control panel includes eight hardwired input terminals for use with traditional hardwired non combus door contacts smoke detectors and or motion detectors The control panel also supports several hardwire zone expansion modules Devices connected to hardwired input terminals must be assigned to a zone and the zone s parameters must be defined see Zone Programming on page 12 Figure 2 6 shows single zone ATZ disabled hardwire input terminal connections recognized by the DigiplexNE system For UL listed installations use EOL resistor part 42011002000 DIGIPLEXNE CONTROL PANEL 7 Figure 2 6 Single Zone Input Connections N C Contacts No EOL N C With EOL UL ULC Configuration CONTROL PANEL TERMINALS CONTROL PANEL TERMINALS OUTPUT Detector Terminals Detector Terminals Zone input COM Zone input COM 1KQ NC N C EOL N O With EOL N C Contacts No EOL UL ULC Configuration With Tamper Recognition CONTROL PANEL TERMINALS CONTROL PANEL TERMINA
48. the Monitoring Station received the arming or disarming report code 9 8 DiAL TONE DELAY SECTION 3037 OPTION 7 Default disabled When option 7 is enabled the dialer hangs up if no dial tone is present after 32 seconds When option 7 is disabled the dialer dials even if no dial tone is present after 3 seconds If more time is required insert a 4 second pause into the desired telephone number sequence see section 8 4 Option Feature 7 ON If no dial tone is present dialer hangs up 7 OFF If no dial tone is present force dials PROGRAMMABLE OUTPUTS o EEIT A PGM is a programmable output that toggles to its opposite state i e a normally open PGM will close when a specific event occurs in the system For example a PGM can be used to reset smoke detectors activate strobe lights open close garage doors and much more When a PGM closes the control panel supplies a ground to the PGM activating any device or relay connected to it When a PGM opens the circuit opens from ground therefore not providing any power to the devices connected to it The control panel provides a maximum of 100mA to PGM1 and 5A to PGM2 and PGM3 PGM1 is a normally open transistor output and PGM2 and PGMG are normally open or normally closed 5A relays For details on how to connect a relay to a PGM please refer to section 2 8 on page 4 10 1 PGM ACTIVATION EVENT The PGM Activation Event determines which event wil
49. the capability of protecting the area alone 4 5 7 Delay Before Alarm Transmission SECTIONS 0101 To 0196 OPTION 8 Default 000 When an alarm condition occurs on a zone with option 8 enabled the control panel activates the bell output but will not report the alarm to the Monitoring Station until the end of the Alarm Transmission Delay During this period disarming the system cancels any report originating from this zone To program the Alarm Transmission Delay key in the desired value 000 to 255 seconds 000 instant into section 3055 This feature is commonly used with Entry Delay zones to reduce false alarms created by new users who may not disarm the system in time 4 6 INPUT SPEED 001 to 255 X 30msec default 600ms The Input Speed defines how quickly the control panel responds to an open zone detected on any hardwired input terminal does not apply to addressable motion detectors and door contacts All other zone definitions and options do not come into effect until the Input Speed elapses The control panel will not display and or respond to an open zone until the Input Speed elapses to prevent glitches from causing an alarm or unnecessary reporting For example if an armed zone with an Input Speed of 600ms opens and closes in less than 600ms the control panel will not respond i e no reporting no alarm and no display on the keypad Set the Input Speed 001 to 255 X 30ms default 600msec
50. to 15 00 all doors Access Level amp Schedule Assignment Enter digits Second Brackets Schedule Enter number from 00 to 15 00 all times Access Control Options 1 Access Control Access 2 Can Disarm with Access Card Control User 3 Card with Door Unlocked Period Extension Options 4 5 Feature Feature Select off off Cannot Arm with Card arming disabled Programming on off Can Regular Arm with Card off on Can Stay Arm with Card on on Can Force Arm with Card 6 Add Tolerance Window to Schedules 7 off Code can arm disarm A access anytime on Code follows Schedule 8 off Valid Card can be granted access and disarm partition on Valid Card can be granted access but Code required to disarm partition Press the A key Enter Access Card Press ENTER or A to save and go to the next section Access Card Assignment Enter Access Card s serial number manually or present Card to the reader 12 5 USER OPTIONS SECTIONS 1002 TO 1999 USER OPTIONS SCREEN OPTIONS 1 TO 8 The User Options define how each User Access Code can arm or disarm the partitions All users can Regular Arm see section 15 1 their assigned partitions but only those with the Arm Only option disabled can disarm an assigned partition Enable or disable the options as required for each User Access Code as shown in Figure 12 1 Option 1 Feature Description 1 2 User cannot create or modify other User
51. to 231 000 to 231 255 Any User Code Not Used Not Used 000 User Codes 001 to 255 001 to 255 001 to 255 001 User Codes 256 to 511 000 to 255 000 to 255 010 Arming with User Code 002 User Codes 512 to 767 000 to 255 000 to 255 003 User Codes 768 to 999 000 to 231 000 to 231 255 Any User Code Not Used Not Used 000 Keyswitch numbers 001 to 032 001 to 032 011 Arming with Keyswitch 255 Any keyswitch Not Used Not Used Auto Arming 000 000 012 Special Arming 000 Arming with WinLoad 001 001 Late to Close 002 002 DIGIPLEXNE CONTROL PANEL 45 Event Group Feature Group Feature Start No Movement Arming Partial Arming One touch Arming Special Arming cont d ak GE Aas Ai uture Use In Touch Voice Module Arming Any special arming event Not Used Not Used User Codes 001 to 255 001 to 255 001 to 255 User Codes 256 to 511 000 to 255 000 to 255 Disarm with Master User Codes 512 to 767 000 to 255 000 to 255 User Codes 768 to 999 000 to 231 000 to 231 Any User Code Not Used Not Used User Codes 001 to 255 001 to 255 001 to 255 User Codes 256 to 511 000 to 255 000 to 255 Disarm with User Code User Codes 512 to 767 000 to 255 000 to 255 User Codes 768 to 999 000 to 231 000 to 231 Any User Code Not Used Not Used Keyswitch numbers 001 to 032 001 to 032 Any keyswitch Not Used Not Used User Codes 001 to 255 001 to 255 001 to 255 User Codes 256 to 511 000 to 255 000 to 255 Disarm after alarm with Master User Codes 512 to 767 000 to 255 000
52. to 255 User Codes 768 to 999 000 to 231 000 to 231 Any User Code Not Used Not Used User Codes 001 to 255 001 to 255 001 to 255 User Codes 256 to 511 000 to 255 000 to 255 Disarm after alarm with User Code User Codes 512 to 767 000 to 255 000 to 255 User Codes 768 to 999 000 to 231 000 to 231 Any User Code Not Used Not Used Keyswitch numbers 001 to 032 001 to 032 Any keyswitch Not Used Not Used User Codes 001 to 255 001 to 255 001 to 255 User Codes 256 to 511 000 to 255 000 to 255 Alarm Cancelled with Master User Codes 512 to 767 000 to 255 000 to 255 User Codes 768 to 999 000 to 231 000 to 231 Any User Code Not Used Not Used User Codes 001 to 255 001 to 255 001 to 255 User Codes 256 to 511 000 to 255 000 to 255 Alarm Cancelled with User Code User Codes 512 to 767 000 to 255 000 to 255 User Codes 768 to 999 000 to 231 000 to 231 Any User Code Not Used Not Used Keyswitch numbers 001 to 032 001 to 032 Any keyswitch Not Used Not Used Auto Arm Cancelled 000 000 One touch Stay Instant Disarm 001 001 Disarming with WinLoad Disarming with WinLoad after alarm WinLoad cancelled alarm Future Use Future Use Future Use Disarm with Keyswitch Disarm after alarm with Keyswitch Alarm Cancelled with Keyswitch Special Disarming 46 REFERENCE amp INSTALLATION MANUAL
53. to 255 days into the appropriate section Enter 000 to disable the Closing Delinquency Timer For example the Closing Delinquency Timer for partition 1 section 3119 is programmed for 005 days When the system is disarmed DigiplexNE will begin the Closing Delinquency Timer for partition 1 If the partition has not been armed within five days DigiplexNE will transmit a Closing Delinquency report code to the central monitoring station Partition 1 3119 Partition 2 3219 Partition 3 3319 Partition 4 3419 Partition 5 3519 Partition 6 3619 Partition 7 3719 Partition 8 3819 DIGIPLEXNE CONTROL PANEL 29 DIALER OPTIONS A 9 Hs 9 1 TELEPHONE LiNE MONITORING SECTION 3036 OPTIONS 1 AND 2 When enabled the system verifies the existence of the main telephone line once every second After each successful test the Status LED on the control panel flashes briefly A line test failure occurs when the TLM detects less than 3 volts for the period defined by the TLM Fail Timer see section 9 1 1 If the line test fails the control panel will generate one or more conditions as defined by the TLM settings below until it detects the telephone line again When the dialer detects a telephone ring the TLM test stops for 1 minute Option Feature When the line test fails 1 2 OFF OFF Disabled TLM disabled default
54. to 96 The third set of 2 digits refer to the Tamper Report Codes that can be sent to the Monitoring Station to identify which zone experienced a tamper or wire fault If the Tamper Recognition Options see section 7 5 are disabled the control panel will not report the occurrence of any tampers or wire faults The fourth set of 2 digits refer to the Tamper Restore Report Codes that can be sent to the Monitoring Station to identify which zone was restored 8 2 3 Keyswitch Arming SECTIONS 0701 To 0732 A report code can be programmed for each of the 32 keyswitch zones Each section from 0701 to 0732 corresponds to a keyswitch from 1 to 32 When using a keyswitch to arm a partition the control panel can send the report code to the Monitoring Station identifying which keyswitch was used The control panel will not send report codes for keyswitches that are defined with the PGM Activation definition 8 2 4 Keyswitch Disarming SECTIONS 0801 To 0832 A report code can be programmed for each of the 32 keyswitch zones Each section from 0801 to 0832 corresponds to a keyswitch from 1 to 32 When a keyswitch is used to disarm a partition the control panel can send the report code to the Monitoring Station identifying which keyswitch was used The control panel can transmit the report codes every time a partition is disarmed or only when it is disarmed following an alarm Also refer to Disarm Reporting Options in section 8 13 The contro
55. to the public switched telephone network PSTN However due to differences between the individual PSTNs provided in different countries the approval does not of itself give an unconditional assurance of successful operation on every PSTN network termination point In the event of problems you should contact your equipment supplier in the first instance General Warning This equipment must be installed and maintained by qualified service personnel only Warranty Paradox Security Systems Ltd Seller warrants its products to be free from defects in materials and workmanship under normal use for a period of one year Except as specifically stated herein all express or implied warranties whatsoever statutory or otherwise including without limitation any implied warranty of merchantability and fitness for a particular purpose are expressly excluded Because Seller does not install or connect the products and because the products may be used in conjunction with products not manufactured by Seller Seller cannot guarantee the performance of the security system and shall not be responsible for circumstances resulting from the product s inability to operate Seller obligation and liability under this warranty is expressly limited to repairing or replacing at Seller s option any product not meeting the specifications Returns must include proof of purchase and be within the warranty period In no event shall the Seller be liable to the buye
56. two programmable time periods called Interval A and Interval B For each Interval determine when users will have access by programming the Start Time in the first screen and the End Time in the second screen according to the 24hr clock i e 9PM 21 00 The Intervals are only valid during the days programmed in the third screen Option 8 in the third screen represents the programmed holidays see section 13 8 When option 8 is enabled users have access between the Start Time and End Time during the holidays An Interval cannot cross into another day overnight Schedules are assigned to the users through their User Access Codes refer to the System Manager s Manual For example program Schedule 001 in section 2401 A Start time 09 00 End time 17 00 options 2 3 4 5 and 6 enabled B Start time 10 00 End time 17 00 options 1 7 and 8 enabled Then any User Access Code with this Schedule assigned will have access Monday to Friday from 9AM to 5PM and on Saturday Sunday and Holidays from 10AM to 5PM Primary Schedules 001 to 015 are programmed in sections 2401 to 2415 respectively Secondary Schedules 016 to 032 are programmed in sections 2416 to 2432 respectively For each Schedule enter the Start Time End Time and enable or disable the options as required for each Interval Schedule 000 allows the user access at all times Only Primary Schedules can be assigned to User Access Codes Secondary Schedules are used as
57. wire Units PU run of wire Units PU run of wire Units PU 100ft 30m 700 100f 30m 700 100ft 30m 700 200ft 61m 700 200ft 61m 682 200ft 61m 429 300ft 91m 700 300ft 91m 454 300ft 91m 286 400ft 122m 700 400ft 122m 341 400ft 122m 214 500ft 152m 690 500ft 152m 273 500ft 152m 171 600ft 183m 575 600ft 183m 227 600ft 183m 143 700ft 213m 493 700ft 213m 195 800ft 244m 431 800ft 244m 170 900ft 274m 383 900ft 274m 151 1000ft 305m 345 1000ft 305m 136 1500ft 457m 230 2000ft 610m 172 2500ft 762m 138 3000ft 914m 115 6 REFERENCE amp INSTALLATION MANUAL Figure 2 4 Sample Power Requirement Calculations Power required by devices connected to control panel s auxiliary output must not exceed the auxiliary output s limit A B C D E F G 368PU 700PU OK Control Panel aux output 700PU APR3 PRT1 IDGP2 641 A 40PU D 80PU 7 5m 25ft 15m 50ft APR3 ZX8 Sp DGP2 70 B 28PU E 30PU 22 AWG ers Ges 30m 100ft As indicated in Table 2 on page 6 this run of wire can support 700PU Total PU on this run of wire A 40PU B 28PU 68PU 700PU OK 290m 950ft SHH As indicated in Table 2 ENS on page 6 this run of DGP2 60 A wire can support 454PU C 30PU D Total PU on this run of EE wire D 80PU E 30PU F 80PU G
58. 0 to 255 003 User Codes 768 to 999 000 to 231 000 to 231 255 Any User Code Not Used Not Used 032 Zone Shutdown 001 to 096 001 to 096 000 033 Zone Tamper 255 any zone Zone Numbers 001 to 096 001 to 096 034 Zone Tamper Restore 001 to 096 001 to 096 035 Special Tamper 000 Keypad Lockout 000 000 TLM Trouble see NOTE 2 on page 50 000 000 AC Failure 001 001 Battery Failure 002 002 000 Auxiliary Current Limit 003 003 036 Trouble Event Bell Current Limit 004 004 Bell Absent 005 005 Clock Trouble 006 006 Global Fire Loop 007 007 255 Any Trouble Event Not Used Not Used TLM Trouble see NOTE 2 on page 50 000 000 AC Failure 001 001 Battery Failure 002 002 000 Auxiliary Current Limit 003 003 037 Trouble Restore Bell Current Limit 004 004 Bell Absent 005 005 Clock Trouble 006 006 Global Fire Loop 007 007 255 Any Trouble Restore Event Not Used Not Used DIGIPLEXNE CONTROL PANEL 47 Event Group Event Feature Group Feature Start End Module Tamper ROM RAM error TLM Trouble Fail to Communicate Module Trouble Printer Fault AC Failure Battery Failure 007 Auxiliary Failure 008 008 Any Module Trouble Event Not Used Not Used Combus Fault 000 000 Module Tamper 001 001 ROM RAM error 002 002 TLM Trouble 003 003 Fail to Communicate 004 004 Module Trouble Restore Printer Fault 005 005
59. 0601 To 0632 FIRST DIGIT 3 When option 3 is enabled a Utility Key Event will be generated whenever the keyswitch input is opened see Table 14 on page 51 This option can be used to activate or deactivate one or more of DigiplexNE s PGM outputs When a keyswitch is defined with the Generate a Utility Key Event on Open option the Keyswitch Partition Assignment and Keyswitch Options are disabled To program a Keyswitch to generate a Utility Key Event 1 Program the Activation Event of a PGM output with the Utility Key Event corresponding to the desired keyswitch see PGM Programming Table in the Programming Guide Event Group 048 2 Enable option 3 in the section corresponding to the desired keyswitch 5 2 5 Generates a Utility Key Event on Open and Close SECTIONS 0601 TO 0632 FIRST DIGIT 4 When option 4 is enabled a Utility Key Event will be generated whenever the keyswitch input is opened and closed As a result the Utility Key Events increase from 32 to 64 events when option 4 is enabled one event for each state open and closed See Table 14 on page 51 This option can be used to activate or deactivate one or more of DigiplexNE s PGM outputs When a keyswitch is defined with the Generate a Utility Key Event on Open and Close option the Keyswitch Partition Assignment and Keyswitch Options are disabled To program a Keyswitch to generate a Utility Key Event 1 Program the Activation Event of a PGM output with t
60. 2 8 smoke detector input see section 2 Wire Detectors 10 6 Connect the 2 wire smoke detectors as shown in Figure 2 8 S Ie using a 1k 2 EOL resistor If a line AUX N O contacts short occurs or the smoke detector 8 1KQ activates whether the system is EOL armed or disarmed the control panel will generate an alarm If the line is Smoke detectors open the Zone Fault trouble indication appears in the Trouble Display and the report code is sent to the Monitoring Station if programmed Note It is recommended that the smoke detectors be connected in a daisy chain configuration UL Note Not to be used with UL Listed systems 2 17 2 ESL CleanMe Installation The DigiplexNE control panel supports ESL smoke detectors that have the CleanMe feature Connect ESL smoke detectors like the standard smoke detectors shown in Figure 2 8 Avoid connecting more than 20 ESL smoke detectors When an ESL smoke detector sends a CleanMe signal the control panel will generate a Zone Fault trouble and if programmed will transmit the Fire Loop report code to the Monitoring Station The trouble will be cleared if there is no CleanMe signal for 255 seconds If an alarm occurs the trouble will be cleared until it is detected again 2 17 3 Smoke Detector Installation 4 Wire Recommended System Sensor model Figure 2 9 4 Wire Detectors 2112 24D smoke detectors Connect the 4 wire smoke detectors and a relay as UL ULC INSTALLATION shown in Figu
61. 3030 OPTION 7 Default OFF When an activated bell output is shorted a Bell Current Limit trouble is displayed and can be sent to the Central Station This feature determines how the Bell Current Limit trouble is cleared Option Description When an activated bell output is shorted the Bell Current Limit trouble will remain displayed until it is manually cleared by the user The user must clear the trouble through the trouble display 7 ON When an activated bell output is shorted the DigiplexNE control panel will attempt to reactivate the bell output once every minute for as long as the bell is activated The Bell Current Limit trouble is cleared automatically the first time the control panel does not detect a short when attempting to reactivate the bell 7 OFF UL Note For UL installations section 3030 option 7 must be A enabled ON Only troubles that have been corrected can be cleared If a trouble has not been corrected it will continue to be displayed even if the user tries to clear the trouble through the trouble display APPENDIX 1 PGM PROGRAMMING TABLE a Event Group Event Feature Group Feature Start End Zone is OK 001 to 096 001 to 096 Zone is Open 000 001 to 096 001 to 096 Zone Numbers Zone is Tampered 255 any Zone 001 to 096 001
62. 50 Bus Fault a module was removed from the combus PS Moce Tamper Ree On ogee era melon 3952 ROM Check Error on board Read Only Memory trouble NEE ei 3954 Module Fail to DGP2 DVAC failed to communicate with Communicate the Monitoring Station 3955 Printer Fault Printer Module detected an error 3956 Module AC Failure no AC power detected on a module Module Battery battery on a module is disconnected or the 3957 l Failure battery voltage is low Module Auxiliary The AUX output on a module has 3958 e Failure exceeded current limits 3959 Future Use Future Use 3960 Wireless Trans the battery voltage is low on a wireless mitter Low Battery transmitter 3961 Wireless Module This report code is global unless using the Supervision Failure Contact ID or SIA reporting formats 3962 to 3964 Future Use 3965 Fail to Com 1 Phone Number 1 failed to communicate 3966 Fail to Com 2 Phone Number 2 failed to communicate 3967 Fail to Com 3 Phone Number 3 failed to communicate 3968 Fail to Com 4 Phone Number 4 failed to communicate No Fail to Communicate for Pager telephone numbers 8 2 12 System Trouble Restore Codes When a trouble described in sections 3940 to 3961 is corrected the control panel can send the report code to the Monitoring Station Section Event Section Event 3970 TLM1 Restored 3981 Module Tamper Restored 3971 AC Restored 3982 ROM Ch
63. 9 BEE EE ene repete venus 9 Special Characters eeneg Aude e eee seg EE BR YE maa XR QI ert eder DEER 34 Special Telephone Number Keys 26 Speed BUS inuit 32 Standard 24Hr Fire TTT 14 Standard Pulse Formats seriti se de eek eke ek Re ke eases mee 27 Stat A 31 Stay Arming EE Ee AA diia 42 Stay Arming with Delay 42 Stay Delay ZONE i ee cueste a o dete re nre oan oA I ee e ER 14 Stay ZON SS RP 15 Supervision Bypass Options 21 Swinger Shutdown See Auto Zone Shutdown Switch To HUE 30 Switch To Stay Arming iese ek ee sk GRA Ee ek AA AR ee mene 19 System Date and TIME ie oie ee EENS NENNEN dE dE EE 33 System EVER ae es ec E Be EE efe DE ER d E 52 System Labels is RE RR ee ee DEER ht dig EN Qul es geg EUR 34 System Master Code Ee ee Ee ee ek ea ee Ee iaa ea 36 T Tamper Bypass Options 22 Telephone Line Connection Examples 9 Telephone Line Connections sss 9 Telephone Line Monitoring TLM ee ee e e e mI 30 Test REDOM AE EE m a T cente e e en ni n P RR AN ie e S 33 TestreportS EE o edhe tee ee ende RU A e kaa d dp 28 Timed Test Transmission when Armed Disarmed 28 TEM Fail TIMOR wide estes e teet met vet vr Eae Ye eI ete e Van 30 Tolerance Window sssssssssssss mm mee 26 39 Tone DTME formiat trivia de Ree 30 Transformer EE 4 Transmit Zone Status on Serial Port 32 Tro ble Display seg aan Zd a wa RD D it eek 43 Trouble L aG a o EL ee a esa dy
64. Auxiliary supply trouble Combus fault restore Module tamper restore Module ROM RAM error restore Module TLM restore Printer fault restore Module AC restore Module battery restore Module Auxiliary supply restore Fail to communicate with central station Module RF low battery Module RF battery restore Module RF supervision trouble Module RF supervision restore Cold Start Warm Start Test Report engaged PC software communication finished Installer on site Installer programming finished Default Contact ID Report Code for sections 4032 to 4037 3 3A1 AC loss restore 3 3A9 Battery test restore 3 3AA System trouble restore 3 321 Bell 1 restore 3 321 Bell 1 restore 3 625 Time Date Reset 3 373 Fire trouble restore 1 333 Expansion module failure 1 145 Expansion module tamper 1 3A4 Rom checksum bad 1 352 Telco 2 fault 1 354 Fail to communicate 1 336 Local printer failure 1 3A1 AC loss 1 3A9 Battery test failure 1 3AA System trouble 3 333 Expansion module failure restore 3 145 Expansion module tamper restore 3 3A4 Rom checksum bad restore 3 352 Telco 2 fault restore 3 336 Local printer failure restore 3 3A1 AC loss restore 3 3A9 Battery test failure restore 3 3AA System trouble restore 1 354 Fail to communicate 1 384 RF transmitter low battery 3 384 RF transmitter battery restore 1 381 Loss of supervision RF 3 381 Supervision restore RF
65. Backup Schedules see section 13 7 Section Start Time End Time Days 1st Screen 2nd Screen 3rd Screen f A setas per setas per 1 Sunday S Schedule 001 2401 24hr clock 24hr clock 2 Monday M to 3 Tuesday T Schedule 032 2432 pg Set as per setas per y 1243211 B nr clock 24hr clock 14 Wednesday W 5 Thursday T 6 Friday F 7 Saturday S extended by 1 hour before and 1 hour after their assigned Schedule see Figure 13 2 Figure 13 2 Example of a Schedule Tolerance Window User s assigned Schedule is 9AM to 5PM When Add Tolerance Windows to Schedules is enabled for the user the user has access from 8AM to 6PM E Schedule Tolerance Windows d ll Schedule BAM 9AM SPM 6PM only section 13 6 The Schedule Tolerance Window does not apply to the Arming and Disarming Report Schedules section 8 3 1 and section 8 3 2 The Schedule Tolerance Window applies to Access Schedules 13 10 DOOR ACCESS MODE SECTION 2251 To 2282 OPTION 1 Each Access Door can be assigned to one or more partitions in the security System and each user can be assigned to one or more partitions This means that the actions performed by the user will be directly linked to the partition s assigned to that door Doors 01 to 32 are programmed in sections 2251 to 2282 respectively For each door enable or disable the option as required 13 7 BAC
66. D I G IL cx a LF WO alu Wu CE FC ale LISTED V1 4 96 Zone Expandable Security and Access Control Panel d A aos v PX Om ate y gt ka i T ones ao DGP NE96 GOAR Reference and Installation Manual RA D OO Xx RIT Y SY S TEM S www paradox ca A c U TABLE OF CONTENTS INTRODUCTION Ee EER ieee Ee redeo on siga senis 3 id T 3 Specifications sssini ie enea de ned 3 INSTALLATION coi d Recommended Installation Procedure 4 Location amp Mounting seen 4 Earth Ground eoi Ho RR GRAUE 4 ede IERE EE dure ere rie era oet 4 Backup Batalla e E ee Ries 4 Auxiliary Power Terminals seen 4 Bell siren Output o iere Lien e Le 4 Programmable Output 4 Keyswitch Connections sse 4 Access Control Connections eene 4 Calculating Power Requirements seseeseeseeeeeereereerreereeeee 6 Keypad Zone Connections sse 7 Addressable Zone Connections sees 7 Double Zone Connectons ee eee ee ee ee 8 Connecting the DGP2 ZX4 sse 8 Combus Connections esee 9 SCHER 9 Telephone Line Connections sees eee ee ke ee eee e 9 B lilt in RATO cinto TTT 10 PROGRAMMING METHODS 11 WinLoad Uploading Downloading Software 11 Paradox Memory Key essere 11 Module Broadcast eite t eterne 11 Programming Through a Keypad AAA 11 Module Programm
67. DELAY WHEN ARMING WITH ACCESS CARD SECTION 3038 OPTION 6 Default disabled When an Access Card is presented to a reader twice within approximately 5 seconds with the door closed some or all the partitions see section 13 10 assigned to the Access Door can arm with or without starting the Exit Delay This feature is useful when the reader is outside the partition so the partition s can be armed immediately Option When arming with an Access Card 6 ON The Exit Delay is cancelled 6 OFF The Exit Delay is triggered 13 14 RESTRICT ARMING ON DOOR SECTION 2251 To 2282 OPTION 4 With option 4 ON the control panel can prevent an Access Card from arming the partition s assigned to the door even if the Access Card is programmed to permit arming 13 15 RESTRICT DisARMING ON DOOR SECTION 2251 To 2282 OPTION 5 With option 5 ON the control panel can prevent an Access Card from disarming the partition s assigned to the door even if the Access Card is programmed to permit disarming 13 16 DOOR ACCESS DURING CLOCK Loss SECTION 3038 OPTION 8 Default disabled If the system registers a Clock Loss Trouble the control panel will no longer recognize the Schedules Only the System Master Code and User Access Codes with the Master feature enabled can reset the clock when option 8 is enabled To avoid Clock Loss a RTC is incorporated in the control panel Enable or disable the option
68. ION OPTION The PGM Deactivation Option see section 10 2 must be set to PGM Timer for this feature to function The Flexible PGM Deactivation Option uses the benefits of both the PGM Deactivation Event see section 10 4 and the PGM Timer see section 10 5 When option 3 is enabled and the PGM is activated see section 10 1 it will deactivate when either the PGM Deactivation Event occurs or the PGM Timer elapses whichever happens first For example the PGM activates and the PGM Timer is set for 5 minutes However the PGM Deactivation Event occurs before 5 minutes ends so the PGM deactivates Enter the section corresponding to the PGM and enable option 3 default disabled PGM 1 0919 PGM 2 0929 PGM 3 0939 10 4 PGM DEACTIVATION EVENT The PGM Deactivation Event determines which event will return the PGM to its original state The Event Group specifies the event the Feature Group identifies the source and the Start and End determine the range within the Feature Group The complete PGM Programming Table appears in the Programming Guide For example to deactivate PGM1 when zone 3 opens program Event Group section 0914 001 Zone is Open Feature Group section 0915 000 Zone Numbers Start section 0916 003 End section 0917 003 Enter the sections that correspond to the Event Group Feature Group Start and End of the desired PGM and enter the desired 3 digit n
69. KUP SCHEDULES SECTION 2501 To 2532 When an Access Card or User Access Code is used at an Access Door the control panel verifies whether it was used during its assigned Primary Schedule If the Primary Schedule is linked to another Schedule it will verify the linked Schedule and any Schedule linked to it The control panel will verify up to 8 linked Schedules one after another until it determines whether the card or code is valid Each Schedule Primary or Secondary from 001 to 032 can be linked to another Schedule in sections 2501 to 2532 respectively In each section enter the 3 digit Schedule number of the Schedule to be linked with it For example if Schedule 001 is linked to Schedule 005 and Schedule 005 is linked to Schedule 030 then the control panel will verify Schedules 001 005 and 030 13 8 HOLIDAY PROGRAMMING SECTIONS 2701 To 2712 Holiday Programming identifies the days that are considered holidays in the Schedules When option 8 is enabled in sections 2401 to 2432 access is permitted during the holidays Each section from 2701 to 2712 represents a month from January to December respectively Each section includes four groups of five to eight options that represent the days of the month Enable the options representing the holidays For example if 1 and 2 are enabled in the first screen in section 2701 then January 1 and 2 are designated as holidays 13 9 SCHEDULE TOLERANCE WINDOW SECTION
70. LS TAMPER ALARM RELAY OUTPUT OUTPUT Detector Terminals Zone input 1KQ2 COM Zone input COM 1 e T i 1KQ N O Detector Terminals TAMPER N C SWITCH N C With EOL With Tamper amp Wire Fault Recognition UL ULC Configuration N O With EOL With Tamper amp Wire Fault Recognition Enable ATZ see section 4 2 on page 13 and connect as follows extra input cannot be used CONTROL PANEL TERMINALS CONTROL PANEL TERMINALS TAMPER OUTPUT OUTPUT Detector Terminals Detector Terminals Zone input COM Zone input COM 1KQ 22KO 1KQ KO 22KQ TAMPER EOL N C SWITCH TAMPER EOL N O SWITCH for installations without EOL remove 1KQ 8 REFERENCE amp INSTALLATION MANUAL 2 14 DOUBLE ZONE CONNECTIONS Enabling the ATZ feature see section 4 2 allows you to install two detection devices per input terminal Connect the devices as shown in Figure 2 7 Devices connected to input terminals must be assigned to a zone and the zone s parameters must be defined see Zone Programming on page 12 For UL listed Burglary System installations only use EOL resistor part 2011002000 Figure 2 7 Double Zone Connections N C No EOL Resistor CONTROL PANEL TERMINALS L Za 2 ORANGE Detector 1 Terminals Zone input COM Detector 2 Terminals N 9 COM Wei ALARM RELAY OUTPUT NC NC CONTROL PANEL TERMINALS Detector 1 Terminals Zone input COM Dete
71. ONS 0101 To 0196 FIRST DIGIT 9 When a 24Hr Heat zone opens whether it is armed or disarmed the control panel will immediately generate an alarm The SIA FSK reporting format includes specific codes to identify the alarm as a Heat Alarm UL Note UL Listed compatible devices shall be used for UL systems For UL Listed systems this type of zone shall be programmed as a pulsing Fire alarm DIGIPLEXNE CONTROL PANEL 13 4 3 10 24Hr Water Zones SECTIONS 0101 To 0196 FIRST DIGIT A When a 24Hr Water zone opens whether it is armed or disarmed the control panel will immediately generate an alarm The SIA FSK reporting format includes specific codes to identify the alarm as a Water Alarm 4 3 11 24Hr Freeze Zones SECTIONS 0101 To 0196 FIRST DIGIT B When a 24Hr Freeze zone opens whether it is armed or disarmed the control panel will immediately generate an alarm The SIA FSK reporting format includes specific codes to identify the alarm as a Freeze Alarm UL Note UL Listed compatible devices shall be used for UL systems For UL Listed systems this type of zone shall be programmed as a silent auxiliary alarm 4 3 12 Delayed 24Hr Fire Zone Not to be used with UL Listed systems SECTIONS 0101 To 0196 FIRST DIGIT C The Delayed 24Hr Fire Zone definition from Figure 4 3 on page 14 is commonly used in residential homes where a smoke detector often generates false alarms i e cigarette smoke burning bread e
72. PUT NUMBER where the hardwire device is connected NOTE For addressable PIRs door contacts and keypads no input is required 4 1 ZONE NUMBERING SECTIONS 0001 TO 0096 Zone Parameters Sections 0101 to 0196 represent zones 1 to 96 respectively Zone Definition First Digit Zone Partition Assignment Second Digit Y Zone Options Feature Select Press ENTER The Zone Numbering feature is used to individually assign each detection device to any zone in the DigiplexNE system see Figure 4 1 The Zone Parameters define the type of zone the zone s partition assignment and how the control panel will react when an alarm occurs on that zone see section 4 3 to section 4 5 To assign an addressable PIR or door contact to the combus program the module s serial number into the section corresponding to the desired zone i e program zone 34 in section 0034 To assign a detection device connected to a module or control panel s hardwired input terminal program the module s or control panel s serial number and the input number where the device is connected into the section corresponding to the desired zone See the Module Programming Guide for details of its input numbers input numbers not required for keypad zones A 12 REFERENCE amp INSTALLATION MANUAL If PGM1 is defined as a smoke detector input see section 10 6 the control panel will recognize it
73. Report Codes When using one of the special disarming features listed below the control panel can send the report code to the Monitoring Station identifying how the System was disarmed The control panel can transmit the report codes every time a partition is disarmed or only when it is disarmed following an alarm Also refer to Disarm Reporting Options in section 8 13 Section Event Description partition disarms during the Auto Arm s 5920 Qancel Auto Arm 60 sec delay see section 6 9 partition disarms using One Touch EI SIM Disarm Disarming feature see section 6 15 3922 PC Disarm System disarmed using WinLoad or NEware software 3923 PC Disarm after System disarmed using WinLoad or Alarm NEware software after an alarm occurs indicates that an alarm was cancelled 3924 Cancel Alarm even though the system was not armed when the alarm occurred 3925 Future Use Future Use partition disarmed before Disarming 3228 Early to Open Schedule see section 8 3 2 partition disarmed after Disarming 3927 Late to open Schedule see section 8 3 2 partition disarmed with InTouch Voice 3928 Remote Disarm Assisted Arm Disarm Module APR3 ADM2 8 2 10 Special Alarm Report Codes When an alarm is generated the control panel can send the report code to the Monitoring Station identifying the type of alarm Section Event Description 3930 Emergency Panic th
74. Restrict Arming on Te ET 18 Battery Failure lt lt tee eq ee Ee e Me ese dene vt vs 18 Bell or Auxiliary Failure esses 18 Drm 40 Module Iroubles site eee eee e tees RE 18 Supervision LOSS is eit DE tee eere oid TT DEE tee la 18 Ee AE de ex EX Ege Mene Ea ded deer dete v ree 18 TEM Faire ox or ES DE AA Cr T 18 Restrict Disarming on Door xxx see ee eie ee ee RA ER ek eee ee e 40 Ring Counter AI EM 41 Isis Bore aem 20 RIG BREER cete te P No T elle are e Te Pelle ARES Mute es 10 DIGIPLEXNE CONTROL PANEL 57 S Schedule Assignment dusca E Tx raa rae N eee eee ee eee HA TR mene 37 Schedule Tolerance Window 39 Schedule Tolerance Window for Arming Disarming 26 Sched les site uu s etes te tet dE e e one He ve gels 38 Scroll Restart ecoute cette eet deg Cete ne deeem ee dee ded eei n 43 Scrolling Speed scere EE ES EE a X a c aee ie 43 Secondary Schedules eee ee ee eee ee ee eee 39 Serial PoitBaud Rate ree I cared Pons 32 Serial Port Transmission of Zone Status esses 32 Ire E 27 Shabbat Feature oco terree iden daa id nen 33 SIA EStdt UMS 27 SIA Report Gode securi dd Beet dee expe ee perm d dedu ee de ere E 52 Silent Alarme eet eser ee ee Re Ge wile e da 15 22 SilentKnighb fast crescere eter deed AE EE ter eee repo ee eid ba DU 27 SMA A tee dle eov EE PUTES 4 Skip Exit Delay When Arming With Can 40 Sleep Mode See Power Save Mode Smoke Detector eere cdta rd A
75. SA model NP7 12 recommended as shown in Figure 2 3 on page 5 Connect the backup battery after applying AC power When installing verify proper polarity as reversed connections will blow the battery fuse For details on how to set the Battery Charge Current to either 350mA or 700mA see section 11 5 4 REFERENCE amp INSTALLATION MANUAL 2 5 1 Battery Test The control panel conducts a dynamic battery test under load every 64 seconds If the battery is disconnected if its capacity is too low or if the battery voltage drops to 10 5 volts or less when there is no AC the Battery Trouble message will appear in the Trouble Display At 8 5 volts the panel shuts down and all outputs close 2 6 AuxiLIARY POWER TERMINALS The auxiliary power supply can power the motion detectors keypads and other accessories in the security system A fuseless circuit protects the auxiliary output against current overload and automatically shuts down if the current exceeds 1 14 Auxiliary power will resume once the overload condition has restored For details on available output power please refer to Figure 2 3 on page 5 To calculate power consumption see Calculating Power Requirements on page 6 2 7 BELL SIREN OUTPUT The BELL and BELL terminals power bells and or other warning devices that require a steady voltage output during an alarm The bell output supplies 12Vdc upon alarm and can support one 30 watt or two 20 watt sirens The bell output uses a
76. Section 3066 Alternate Dial Reporting Account Number 7 Section 3037 Option 6 3 or 4 digits 0 F in Section 3067 Reporting Account Number 8 3 or 4 digits 0 F in Section 3068 3 Call Central Telephone 3 4 Call Central Telephone 4 Dialing sequences for Alarm Restore Report Codes Partition 1 3128 Partition 5 3528 ma Partition 2 3228 Partition 6 3628 Partition 3 3328 Partition 7 3728 Partition 4 3428 Partition 8 3828 5 Backup on Telephone 1 6 Backup on Telephone 6 7 Backup on Telephone 7 8 Backup on Telephone 8 Dialing sequences for Tamper Hestore Heport Codes Partition 1 3129 Partition 5 3529 kez Partition 2 3229 Partition 6 3629 Partition 3 3329 Partition 7 3729 Partition 4 3429 Partition 8 3829 For each section dialing sequence enable up to 4 central station telephone numbers and 1 backup telephone number The numbers are dialed sequentially from 1 to 4 followed by the backup number This Dialing sequence for sequence will continue until each Trouble Restore Report Codes 3080 OE number has been dialed at least once Dialing sequence for ki System Special Report Codes 3081 gt rL o Ademco Slow Program 2 digit TOES Maximum Dialing Attempt Bul 1 report codes into Section 3056 m 458
77. TWARE EE 14 1 PANEL IDENTIFIER SECTION 3011 Default 0000 The Panel Identifier identifies the control panel to WinLoad before initiating upload or download The control panel will verify if the Panel Identifier in WinLoad is the same If the codes do not match the control panel will not establish communication Therefore program the same Panel Identifier into both the control panel and WinLoad Enter the desired 4 digit hexadecimal number into section 3011 14 2 PC PASSWORD SECTION 3012 Default 0000 The PC Password identifies the computer running the WinLoad software to the control panel before beginning the download process Program the same PC Password into both the control panel and WinLoad If the passwords do not match WinLoad will not establish communication Enter the desired four digit hexadecimal number into section 3012 14 3 PC TELEPHONE NUMBER SECTION 3010 The control panel dials this number to communicate with a computer using WinLoad Enter any digit from 0 to 9 and any special keys or functions see Table 3 Special Telephone Number Keys on page 26 up to a maximum of 32 digits into section 3010 14 4 CALL BACK FEATURE SECTION 3037 OPTION 1 Default disabled The Call Back Feature provides additional security When option 1 is enabled and a computer using WinLoad attempts to communicate with the control panel the control panel hangs up and calls the computer back to re verify id
78. Table 11 Hebrew Special Characters Catalogue 192 119 T 8 H 088 h 168 Q Bi J Z j z 1 043 075 107 123 139 1771 BD IEDER 060 076 092 108 124 172 m S terri 080 HE 032 el bi Li al EI sl E S al Si L Co A el E el E k COGE olslslelolsisie dede alejas 3 e E o al a I El s 3 HT ados 083 E Os DIGIPLEXNE CONTROL PANEL 35 ACCESS CODES 12 1 INSTALLER CODE SECTION 1000 Default 000000 The Installer Code is used to enter the control panel s programming mode which allows you to program all the features options and commands of the control panel and any modules on the combus The Installer Code is six digits in length where each digit can be any value from 0 to 9 To change the Installer Code 1 Press and hold 0 Enter INSTALLER CODE Key in 1000 Enter new 6 digit INSTALLER CODE The Installer Code can program the User Code Options and the A Partition Assignment but cannot program the personal identification numbers Seno 12 2 ACCESS CODE LENGTH SECTION 3033 OPTIONS 2 AND 3 Access codes can be 1 to 6 digits in length When programming access codes with less than 6 digits press the ENTER key after entering the last digit The control panel automatically removes the last 2 digits of the User Access Code if the length is changed from 6 digits to 4 digits However if the User Access Code Length is changed from 4 digits to
79. X 105PU PU InTouch Voice Assisted Arm Disarm Module APR3 ADM2 X 105PU PU Access Control Module DGP2 ACM1P X 165PU PU Note The DGP2 ACM1P consumes 165PU from its own power supply EG Maximum available power units 700PU GRAND TOTAL PU STEP 1 Using Table 1 calculate the total number of power units PU required by each device module and accessory in the system Please take into account devices connected to the control panel s PGM outputs Since the BELL output has its own power supply do not include the sirens connected to it in the calculation STEP 2 If Grand Total is less than 700PU go to step 3 If the value is greater an external power supply is required see Figure 2 5 on page 7 to provide the additional power needed Proceed with step 3 and refer to the example in Figure 2 4 on page 7 STEP 3 Due to the degradation of a power signal over long distances EACH length or run of wire in the system can support only a specific number of power units PU Using Table 2 determine how many power units each length of wire can support Please note that the total number of power units PU can never surpass 700PU Table 2 Power Unit PU Limitations For Each Run of Wire Gauge 18AWG Surface 0 823mm Gauge 22AWG Surface 0 326mm Gauge 24AWG Surface 0 205mm Length of each Available Power Length of each Available Power Length of each Available Power run of
80. ackup battery no AC the control panel can set all keypads into a sleep mode or Power Save Mode In Power Save Mode the keypad s backlight and LEDs are disabled until a key is pressed an alarm occurs or an Entry Delay is triggered 11 21 AUTO TROUBLE SHUTDOWN SECTION 3021 Default 00 If in a 24 hour period a trouble occurs more than the number of times programmed in section 3021 the control panel stops reporting the trouble Enter a value 01 to 15 00 disabled into section 3021 Each trouble has its own counter The counter is reset every day at midnight 11 22 No AC FAIL DisPLAY SECTION 3030 OPTION 6 Default disabled When option 6 is enabled the control panel will not display the AC Failure as a trouble When an AC Failure occurs with this option enabled the AC LED will extinguish the AC Failure report code will be reported the trouble will not appear in the Trouble Display the keypad will not beep to indicate the trouble 34 REFERENCE amp INSTALLATION MANUAL 11 23 MuLTIPLE ACTION FEATURE SECTION 3033 OPTION 1 Default disabled When option 1 is enabled users will remain in the User Menu after entering their access code This allows users to perform more than one action without having to re enter their access code With option 1 off the control panel will exit the User Menu after every action 11 24 SYSTEM LABELS The existing label displayed on the LCD screen can be m
81. alarm When armed Follows Zone Alarm Type The control panel follows the zone s alarm type see section 4 5 5 on page 15 OFF OFF ON OFF DIGIPLEXNE CONTROL PANEL 21 7 5 1 Tamper Bypass Options SECTION 3034 OPTION 7 Default enabled With option 7 enabled in section 3034 the control panel will ignore the zone s bypass definition and will follow the option set in section 7 5 if a tamper or wire fault occurs on a bypassed zone With option 7 disabled Tamper Recognition follows the zone s bypass definition This means that the control panel will not perform any action if a tamper or wire fault occurs on a bypassed zone 7 6 KEYPAD PANIC OPTIONS Default disabled The control panel can generate an alarm audible fire or report only by pressing the keypad Panic key s For LCD keypads two keys are pressed and held simultaneously for 2 seconds For Grafica keypads the appropriate Panic key is pressed and held for 2 seconds Refer to the table below for the keypad Panic keys In the section that corresponds to the desired partition enable or disable options 1 through 6 as desired Partition 1 3123 Partition 3 3323 Partition 5 3523 Partition 7 3723 Partition 2 3223 Partition 4 3423 Partition 6 3623 Partition 8 3823 Option Feature Press and Hold LCD keypads Keys 1 and 3 simultaneously 1 Panic 1 Grafica keypads
82. all be used with the system The listed compatible model PosiProx reader shall be employed off the keypad Control of the Protected Premise In order to have a UL certified system the protected area is to be under the responsibility of one ownership and management i e one business under one name This may be a group of buildings attached or unattached with different addresses but under the responsibility of someone having mutual interest The person of mutual interest is not the alarm installing company Bell Location The alarm sounding device bell must be located where it can be heard by the person or persons responsible for maintaining the security system during the daily arming cycle Protection of the Control Unit The local control unit and the local power supply must be protected by one of the following ways The control unit and audible alarm device must be in a protected area which is armed 24 hours a day N Each partition shall arm the area protecting the control unit and the audible alarm device power supply This may require duplicate protection armed by each partition Access to this protected area without causing an alarm will require that all partitions be disarmed In all cases described above the protected area for the control unit must be programmed as not bypassable CTR 21 Warnings The equipment has been approved in accordance with Council Decision 98 482 EC for pan European single terminal connection
83. and then press the left action key Bypass Repeat this step for any additional zone 4 Press the right action key Back to save the data Users can also activate Bypass Recall Bypass Recall reinstates all the zones that were bypassed the last time the partition s assigned to the User Access Code were armed To activate Bypass Recall users For LCD Keypads 1 Enter their ACCESS CODE 2 Press the BYP key 3 Press the MEM key 4 Press ENTER key to exit For Grafica Keypads 1 Enter their ACCESS CODE 2 Using the scroll keys highlight Bypass and then press the center action key Ok 3 Highlight Bypass Recall and then press the center action key Ok 15 8 CHIME ZONES UL NoTE Nor TO BE USED FOR PERIMETER PROTECTION The keypads can emit rapid intermittent beeps whenever designated zones within their assigned partitions open or when they open during a time period The instructions that follow are for LCD Keypads for Grafica keypads refer to the Grafica Online Manual which can be downloaded for free from our Web site at www paradox ca For LCD keypads To program a Chime Zone users 1 Enter their ACCESS CODE 2 Press the 9 key 3 Press the 1 key 4 Enter the zones 2 digit number or use the A and V keys to scroll the list and press the ACC key when the zone appears on screen 5 Press ENTER key to save To program a time period when the Chime Zones are activated users 1 En
84. as Zones LEES EES 13 Dial Tone Delay cede tods 30 Ground mi eraan EEN 4 Digiplex Memory Key See Paradox Memory Key Disarm Reporting Options sess 28 H Disarming ee EE eene 42 Hardware T en fen er ton t 32 Disarming Report Schedule ees ee ee ke ke Re ER ee 26 Heat Zones A SR RE D EE RD N de Ee GE vet 13 Display Bypass If Armed ses ee se ee eek ee Re ne 20 NT EE de di dee d 13 Door Access Mode eee e Mee 39 Holiday Programming siceraria aaae EnaA SSAA ARa 39 Door Forced Open Restore event ees se se se ee 40 Hourly Test Transmission ee ee ee ee 28 Door Labels EE ES dedo 34 Door Left Open c isis EE Er er CHER EE aaa 38 l Doors Identifier code See Panel Identifier sees 41 jvc A MN MN MM EE o M Burglar Alarm On Door Left Open sses 40 ee 22 Burglar Alarm On Forced Door assos 40 Input Speed ENEE 15 Double Verification for Access See Card and Code Access Installation aaa 4 Double Zone Connections sss e eee eee ee ee e e e ER Ke eee 8 Installer Code EEN 36 DES AMO AVR ARCEM 37 Installer Eunction Keys ege ed ct SE 33 Installer LocK SAM AA AE ee SNE NEEN 32 E Installer Test Mode noo tee hab TR YR dade odias 33 O N E Fa dr 4 Instant Arming TTT 42 STEE E E A S 38 Instant Arming with Delay sees eee ee ee e e eee 42 Enable Arming Disarming Report Schedules acccccccccercccrce 25 Ua 12 Enable Reporting 5 aat Be ee Mee a icai dan 24 EL ET nia bad 15 A EE RER 31 Intellizone Delay 0 0 0
85. ate amp Time 33 TE Gee AE ie EE Clock Compensation Value sene 34 Clear Bell Current Limit Trouble 44 Remove Module eese nenne 34 Serial Number Viewing 34 APPENDIX 1 PGM PROGRAMMING TABLE 45 Power Save Mode sees essen 34 Auto Trouble Shutdown PE CREE Mn een aed 34 APPENDIX 2 AUTOMATIC REPORT CODE LIST 52 No AC Fail Display sesse tard 34 ak Action UUR EE EE ER 34 APPENDIX 3 CONTACT ID REPORT CODE LIST 54 ystem Labels OE EE AE N tede 34 ACCESS CODES ee 36 UNDE RE EE EE OE EE OE ES 55 Installer Gode aedi tette 36 Access Code Lengt 36 WARNINGS es Reeder eer ida 59 System Master Code AAA 36 Programming Access Codes eee eee eee 36 User Options EE ia ld 36 Partition Assignment 37 ACCESS Control tede E seats 37 ACCESS CONTROL SYSTEM FEATURES 38 Common Access Control Tems eee ee eee eee Re ee ee 38 Programming Overview esee 38 Enable Access Control 38 Door Numberirig iere epe rite en 38 Access Levels eiii titi E REG 38 Access Schedules see eee eee eee 38 Backup Schedules seen 39 Holiday Programming sss sse 39 Schedule Tolerance Window sss ee ee eee eee 39 Door Access ModE inisini annin eriei eip een iga 39 Code ACCE Shon a aaea e P d 39 Card and Code AGCGeSS seene 39 Skip Exit Delay When Arming With Access Card 40 Restrict Arming on DOOF eee eee eee 40 Restrict Disarmin
86. ates Trouble Only The control panel displays Zone Fault in the Trouble Display and transmits the defined report code see section 8 2 When armed Follows Zone Alarm Type The control panel follows the zone s alarm type see section 4 5 5 on page 15 When disarmed Generates Audible Alarm The control panel displays Zone Fault in the Trouble Display transmits the defined report code see section 8 2 and ON ON generates an audible alarm When armed Follows Zone Alarm Type The control panel follows the zone s alarm type see section 4 5 5 on page 15 ON OFF 7 3 1 Supervision Bypass Options SECTION 3034 OPTION 3 Default disabled With option 3 enabled in section 3034 the Wireless Transmitter Supervision Options will follow the zone s bypass definition This means that the control panel will not perform any action if a supervision loss occurs on a bypassed zone With option 3 disabled the control panel will ignore the bypass definition and will follow the option set in section 7 3 if a supervision loss occurs on a bypassed zone 7 4 POLICE CODE TIMER Default 000 If an alarm condition occurs on a zone the control panel generates an alarm and triggers the Police Code Timer The Police Code Timer requires confirmation of the alarm situation within the delay before sending the Police Code programmed in 3934 The Police Code will only be sent if one of the following conditions occurs during
87. ault disabled When option 1 is enabled the control panel can prevent arming if it detects a loss of AC power Partitions will not arm until power is restored 6 5 RESTRICT ARMING ON BATTERY FAILURE SECTION 3035 OPTION 2 Default disabled When option 2 is enabled the control panel prevents arming if it detects a battery loss or if the battery voltage is less than 10 5V The control panel will not arm a partition until all battery trouble conditions are corrected 6 6 RESTRICT ARMING ON BELL OR AUXILIARY FAILURE SECTION 3035 OPTION 3 Default disabled When option 3 is enabled the control panel can prevent arming if it detects that the bell or siren is disconnected the Bell Output has exceeded its current limits the Auxiliary Outputs have exceeded their current limits The control panel will not arm any partition until all bell or auxiliary trouble conditions are corrected 6 7 RESTRICT ARMING ON TLM FAILURE SECTION 3035 OPTION 4 Default disabled When option 4 is enabled the control panel can prevent arming if it is unable to access the telephone line The control panel will not arm any partition until all TLM trouble conditions are corrected 6 8 RESTRICT ARMING ON MODULE TROUBLES SECTION 3035 OPTION 5 Default disabled When option 5 is enabled the control panel will monitor the same Restrict Arming options selected for the control panel battery tamper supervision AC
88. cc cee n 15 Entry Delay Timer sie MR es og de Me tado 13 K Entry Delay Timers 3353 SEER SE WER a GR GE WE EERS RE an NENNEN NEE 13 Entry Delay Zones EES dE e ORAE Vue OE SE dade BE SE ERA 13 Key for CCESS BE narran nro rnennc arenas 39 56 REFERENCE amp INSTALLATION MANUAL Keypad Beep on Successful Arm Disarm Report 30 Keypad Lockout ria detener EN ere SEN RS D te Pea aa eU 20 Keypad Numbering sss es ee tnter e rere rur n hr Re ee e enn 15 Keypad Zone Connections 7 Keyswitch AMO a 17 Ile EE 4 Definitions nm 16 DiSabled Cariaco rene ba Yee e Ee Du edad ba s 16 Keyswitch Numbering i e e e e e K mm 16 Maintained 4 sese ged n I ache he ee x p P SR A AN it e UA 16 MOMENT scs sooo ex SR De de EEN 16 Qo EE A A 17 Partition ASSIQNMENE nysa aee dicas 17 Stay Instant Disarm ie i die seco te greed dd EER ede 17 Keyswitch for PGM Activation 17 L Label Broadcast ent bene teer ees 33 Label Programmifig ee G ii deter ees 34 LCD Display Keypad SetlingS os i ER ne do GR ES DE 43 Shabbat Feature ste e ge cete o SEHE es 33 Linked Schedules See Backup Schedules Locate Module cuicos net rn wee VD Ee de ge 33 Location amp Mounting ee d SE eeh A Ada ts 4 Kol Sea EE EER diay ot Main OE EE S 20 Logging Access Control Events 40 M Master IM 37 Maximum Bypass Entries 20 Maximum Dialing Attempts ssssssssse m 28 Message Programming See Label Programming Modul
89. ctor 2 Terminals TANPER TAMPER MC TAMPER N C N C With EOL and Tamper amp Wire Fault Recognition UL ULC CONTROL PANEL TERMINALS Detector 1 Terminals COM Detector 2 22 0 d 5000 Terminals EOL EOL TAMPER NC TAMPER NC 2 15 CONNECTING THE DGP2 ZX4 The 4 Zone Expansion Plug in Device DGP2 ZX4 provides four additional hardwired input terminals 8 zones with ATZ enabled It connects directly to the control panel through its on board EXPANSION connector as shown in Figure 2 3 on page 5 Connect detection devices to the DGP2 ZX4 s terminals in the same way that they are connected to the control panel as shown in Figure 2 6 or Figure 2 7 on page 8 Devices connected to hardwired input terminals must be assigned to a zone and the zone s parameters must be defined Zone Programming on page 12 For the 4 Zone Expansion Module APR3 ZX4 refer to the DigiplexNE Modules Programming Guide Do not use with UL Listed systems 2 16 CoMBUS CONNECTIONS Modules can connect anywhere on the 4 wire combus which can support up to 127 modules Connect in a star and or daisy chain configuration as shown in Figure 2 3 on page 5 The total distance of all runs of wire cannot exceed 914m 3000ft For example if ten runs of wire measuring 305m 1000ft each are connected to the control panel the total distance would be 3048m 10 000ft which exceeds the system s capacity To assign a detection device to a zone in the contr
90. d presented to it to the control panel Request for Exit When a REX device Paradoor 460 installed above an Access Door within a protected area detects movement it sends a request for exit signal to the panel Valid Card An Access Card presented to a reader during its assigned Schedule and within its assigned Access Level 38 REFERENCE amp INSTALLATION MANUAL 13 2 PROGRAMMING OVERVIEW Several features and options for Access Control are available in the DigiplexNE system Some are programmed through the control panel and are explained in this manual Other features and options are explained in the Access Control Module Reference amp Installation Manual The following is the MINIMUM required to program Access Control Step 1 Enable Access Control in section 3038 option 1 Step 2 Assign the Doors in sections 2201 to 2232 Step 3 Create the Access Levels in sections 2601 to 2615 Step 4 Create the Schedules in sections 2401 to 2432 Step 5 Set the Holidays in sections 2701 to 2712 Step 6 Program User Access Codes see section 12 on page 36 Step 7 Program the Access Control Modules see Modules Programming Guide 13 3 ENABLE ACCESS CONTROL SECTION 3038 OPTION 1 Default disabled When option 1 is enabled the Access Control feature is activated The control panel and the doors must be programmed see section 13 2 13 4 DooR NUMBERING SECTIONS 2201 ro 2232 Each door to be monit
91. d seven with seven as the brightest 10 LED zero 15 10 EvENT RECORD DisPLAY The Event Record Display displays the user initiated events that occurred in the system as well as any alarms or troubles The events from all the partitions can scroll on the screen or can be viewed by partition The most recent event is displayed first The Event Record Display can only be viewed through an LCD or Grafica keypad To view the events For LCD Keypads 1 Enter a User Access Code 2 Pressthe 7 key 3 Press Key Displays Key Displays 0 All partitions 5 Partition 5 1 Partition 1 6 Partition 6 2 Partition 2 7 Partition 7 8 Partition 3 8 Partition 8 4 Partition 4 4 Press the V key to view subsequent events 5 Press the CLEAR key to exit Change the order that the Event Record screens appear by pressing the 7 key If you already know the number of the event you want to view press the MEM key and then enter the event s number For Grafica Keypads 1 Enter their ACCESS CODE 2 Using the scroll keys highlight View Status and then press the center action key Ok 3 Highlight View Events and then press the center action key OK If the event list appears on the screen go to step 6 4 Highlight View All Areas or Select Area s and then press the center action key Ok 5 If you selected Select Area s in step 4 highlight the area you wish to view
92. de better results in some cases If the 1 1 5 pulse ratio is not providing the desired results in North American countries the 1 2 ratio may be used Option Feature 5 ON North American pulse ratio of 1 1 5 5 OFF European pulse ratio of 1 2 9 4 Busy TONE DETECTION SECTION 3036 OPTION 6 Default enabled When option 6 is enabled the control panel immediately hangs up if it receives a busy signal when it dials an outside number 30 REFERENCE amp INSTALLATION MANUAL 9 5 SwiTCH To PULSE SECTION 3036 OPTION 7 Default disabled When option 7 is enabled the control panel switches from tone dialing to pulse dialing on the fifth attempt to report events to the Monitoring Station The control panel continues to use pulse dialing until it establishes communication When the control panel switches to another Monitoring Station telephone number it returns to tone dialing and switches back to pulse dialing on the fifth attempt 9 6 BELL ON COMMUNICATION FAIL SECTION 3036 OPTION 8 Default disabled When option 8 is enabled and the control panel fails to communicate with the Monitoring Station when the partition is armed the control panel can enable the BELL output 9 7 KEYPAD BEEP ON SUCCESSFUL ARM OR DISARM REPORT SECTION 3037 OPTION 5 Default disabled When option 5 is enabled and a user arms or disarms a partition the keypad emits a beep tone to confirm that
93. e Broadcast caen rte d d eet adds 11 33 Mod le Reset tegen e tee re een Dreh eR ERR QI ester en 33 Module Sean aere temet ee ertt E aig 33 Multiple Action Feature 34 N No AG Fail Display sie ees E eere te une 34 No Bell Cut Off on Fire Alarm sse eee ee ee e 21 No Exit Delay on Remote Arm sss 20 Noisy Emvironments giccses inaia ai eati iaaii AAA RAAE AETA 9 O One touch Features ia reirei iir EE Ter e erred ete t babs YE de 19 OR Door Access Mode 39 P Pager Forrmat soot bin 27 Pager Reporting Format eee e e e e e e e e e e e e e e eee mmn 27 Panel Answer Options 41 Panel Partition Assignment eise e ee K e K K K ee ee de eke ke ee 33 Panic Options a roseus respi e Mae ie Sedalia 22 Paradox Memory Key css eee e e e e e e e e eee 11 Partition Label iia A EA 34 Partitioning mc c 32 PG Password reah RE RE Re T iia vvv iin Mex eR de Ded n Ee 41 PC Telephone Number sssssss mmn 41 PGB Layout cunas ai a hr f EE eg 5 PGM PGM Activation Event sss 31 PGM Deactivation Event 31 PGM Deactivation Option cescss ER EE ER ER RE ER ee 31 PGM Delay mers ks aT eve qt TER deed ES ve De 31 PGM Time Base Selection sss 31 PGM Programmimg Table 45 PGM See Programmable Outputs PIN anid Card for Access i it deret D ED GEE Y Ve Ee 39 Police GCode TIME ER de ee ne deve de tone e ee na EN S 21 Power Failure Report Delay sess 28 P
94. e ehe dee de 44 Trouble8 2 erret ad dese dd Cue Me Re aaa 43 58 REFERENCE amp INSTALLATION MANUAL U User Access Codes micro ci er x ree M edi een en e neues 36 User Labels See Access Codes User Menu ACCESS ase seide n Ee deht sede eode dade ee M 37 Vd N EE RE N 17 V Valid Card ii ee ie Ga EE RS ti A Gees ek EE 38 Value Clock Compensation 34 W Water ZONOS os eer deu etude e deal a dad ipeo 14 WirlEOad 2 32 MEE it Fa Pd s 11 41 Answer WinLoad 2 1 ccc cece e cee nc cece ence m men 33 41 Call Wiriboad ta ne it BAN miata es hein judi di 33 41 Cancel Communication 33 Wireless Transmitter Supervision Options iese e K e K 21 Z Zon LabelS TT 34 Zone Restore Report Options 28 Zone Status Transmission to Serial Port 32 Zones 24Hr Burglary ZONE iii eR EE REEDS DEE ad 13 PAE BUZZ SS neck sad De sae AE EE AE DE ed re Ee adi 13 24HrFreeze ZONE ES ag a serie ER GR a da 14 24Hr GAS ZONE unida Weed oe de tete RA Ad aeg ae daoa ee s 13 DAHF Heat ZONE EG ed A ea entr de idu da 13 24Hr Hold up zone vet oe egere SERE EE ER DES eee ene xn 13 24Hr Water zone osse hotte be ag EDE exor e reete id 14 Alarm Transmission Delay e eee EE K ee 15 BYPASS PH 14 GONNECHONS sn ette ire e ex tene Ve ndm dn pee 7 57 Jc i o e sees Ee an ataca 13 Delayed 24Hr Fire Zone 14 Disabled voces 4 y eerte A o 13 DOUDIING S 13 Eniry Delay aat sv ee A e EN 13 EOL EMT 15 Lee 13 ee ER EE kis a al 15 Generates a re
95. e panic keys 1 and 3 were pressed non medical see section 7 6 3931 Auxiliary Panic the panic keys 4 and 6 were pressed see section 7 6 3932 Fire Panic the panic keys 7 and 9 were pressed see section 7 6 an alarm is generated within the Recent 3933 Recent Closing Close Delay see section 8 10 Confirmation of an alarm condition 3934 Police Code occurred during the Police Code Timer s delay see section 7 4 the control panel stops regenerating 3935 Ge ee alarms on a zone during the same armed period see section 4 5 1 a Duress enabled access code is keyed in 3936 Duress refer to the Digiplex DigiplexNE LCD Keypad Reference 4 Installation Manual too many invalid codes entered 3937 Keypad Lockout see section 6 17 8 2 11 System Trouble Codes When a trouble is detected the control panel can send the report code to the Monitoring Station identifying the type of trouble Section Event Description 3940 TLM1 Failure TLM failure on main telephone line pa Ac Faire SS SG eta ater aes BE mee ER RE 3943 Auxiliary Supply Ee enri bere current is greater 3944 bell output is disconnected or the current Bell Output 8 is greater than or equal to 3A 3945 Clock Loss panel time lost see section 11 16 3946 Fire Loop Trouble tamper on a fire zone see section 4 3 3947 ro 3949 Future Use 39
96. e receiving antenna 2 increase the separation between the equipment and receiver 3 connect the equipment to an outlet on a circuit other than the one to which the receiver is connected or 4 consult the dealer or an experienced radio tv technician for assistance CAUTION Changes or modifications not expressly approved by PARADOX SECURITY SYSTEMS could void the user s authority to operate the equipment UL and ULC Warnings UL AND C UL INSTALLATION NOTES The control panel DGP NE96 and LCD Keypad DGP2 641 are UL listed in accordance with standard UL1023 Household Burglar Alarm Systems Units standard UL985 Household Fire Warning Units standard UL1635 Digital Alarm Communicator System Units standard UL609 Local Burglar Alarm Units and Systems standard UL365 Police Station Connected Burglar Alarm Units and Systems and standards UL1610 Central Station Burglar Alarm Units This equipment has the capability of being programmed with features and connected to modules not verified for use in UL installations To stay within these standards the installer should use the following guidelines when configuring the system All components of the system should be UL listed for the intended application N If the system will be used for Fire detection the installer should refer to NFPA Standards 72 Chapter 2 In addition once installation is complete the local fire authority must be notified of the installation N T
97. e to access the S TM ues telephone line A module failed to communicate with the 4 Fail to Communicate Monitoring Company The control panel registers a problem with a printer connected to a Printer Module Check printer for problems paper jam no paper no power etc 5 Printer Trouble 6 AC Failure Module power failure 7 Battery Failure Module s battery is disconnected needs to be recharged or needs to be replaced 8 Supply Output Module has exceeded current limits GROUP 4 NETWORK COMBUS A keypad is no longer communicating with DI Missing Keypad the control panel A device is no longer communicating with 2 Missing Module the control panel No communication between the devices 3 General Failure and the control panel Too many devices over 127 are on the 4 Combus Overload combus GROUP 5 ZONE TAMPER Press 5 to display zone s Zones displayed were tampered GROUP 6 ZONE Low BATTERY Zone displayed indicates where a wireless Press 6 to display zone s device s battery needs to be replaced Also the device s yellow light will flash GROUP 7 ZONE FAULT 44 REFERENCE amp INSTALLATION MANUAL Trouble Description A smoke detector is experiencing a wiring problem needs to be cleaned or a wireless device is no longer communicating with its receiver supervision loss Press 7 to display
98. eck Error Restored 3972 Battery Restored 3983 Module TLM Restored Auxiliary Suppl Module Fail to Communicate Dun paet ddl es Restored 3974 Bell Output Restored 3985 Printer Fault Restored 3975 Clock Loss Restored 3986 Module AC Failure Restored 3976 Fire Loop Restored 3987 Module Battery Restored 3977 Future Use 3988 Module Auxiliary Restored 3978 Future Use 3989 Future Use 3979 Future Use 3990 Hs Transmitter Battery estored 3980 Bus Fault Restored MIN Wireless Module Supervision Restored A If the Telephone Line Monitoring see section 9 1 is disabled the control panel will not transmit the TLM report code 8 3 REPORT ARMING AND DISARMING The following two features combine to identify when a partition should be armed and disarmed and enable the control panel to communicate deviations from the normal schedule to the Monitoring Station 8 3 1 Enable Arming and Disarming Report Schedules Default disabled If the partition is armed or disarmed during times not programmed in the Arming and Disarming Report Schedules see section 8 3 2 the control panel will send the corresponding report code Early to DIGIPLEXNE CONTROL PANEL 25 Close 3916 Late to Close 3917 Early to Open 3926 or Late to Open 3927 In the desired section enable options 5 and 6 to enable the Arming and Disarming Report Schedules Partition 1 3122 Partition 3 3322 Partition 5 3522
99. ed 3 digit delay value 001 to 255 seconds into the corresponding section Partition 1 Entry Delay 1 Timer 3111 Entry Delay 2 Timer 3112 Partition 5 Entry Delay 1 Timer 3511 Entry Delay 2 Timer 3512 Partition 2 Entry Delay 1 Timer 3211 Entry Delay 2 Timer 3212 Partition 6 Entry Delay 1 Timer 3611 Entry Delay 2 Timer 3612 Entry Delay zones are commonly used at the entry exit points i e front back door or garage Using different Entry Delays is useful when one entry point requires a longer delay than another These are the same timers used for Stay Delay zones see section 4 3 14 4 3 3 Follow Zones SECTIONS 0101 To 0196 FIRST DIGIT 3 If an armed Follow zone opens the control panel generates an alarm If an armed Entry Delay zone see section 4 3 2 opens before the Follow zone the control panel waits until the end of the Entry Delay before generating an alarm If more than one Entry Delay zone opens before the Follow zone the control panel waits until the end of the first Entry Delay before generating an alarm This feature is commonly used when a motion detector is protecting the area occupied by the entry point keypad This will prevent the motion detector from causing an alarm when a user enters through the entry point to disarm the system 4 3 4 Instant Zones SECTIONS 0101 To 0196 FIRST DIGIT 4 When an armed Instant zone opens the control panel
100. elay cancelled on Remote Arm 20 Bus Connections EES 9 Exit Delay Termination 19 ISE HT TTT 8 Extended Unlocked Period 37 Double Zone Connections sss 8 Keypad Zone Connections xe e ee e e e ee e Ke K 7 E oa sea oe AL ET 31 EE EE EE ER EG eee AES tats LUE N 4 Feature Select Programming sse 11 Single Zone Connections esses 7 Fire Alarmi 222 aeree x ER RE MEN RRR 22 Telephone Line Connections x e e e eee 9 Fire Circuits eee e ene ens 9 Contact ID Pager csssss ee 27 ilg Zone lada tette R e tee tent e clie 9 Contact ID Report Code esser eene rca 52 Fire Zone Delayed 24 14 Contact ID Report Code List sss 54 Fire Zone Standard Z r 14 eri EE raat a ere der a s esse tite de qo de d rta 43 Follow zone a 13 Current setting for charging battery EEN 32 Follow Zone Switches to Entry Delay 3 19 Force AI esse ee RS Ae ES RA dd eet be de DR seer re 42 D Forc Zonasi aea sedeo ST TE TUA A EE E EEE Den 15 Daylight Savings Time ees ee se ee se e e EER e ee 32 Forced Door SESSE SEE EES 38 Delay Alarm Transmission 15 Freeze Zones EET eese bet bi e rer e e se anaa 14 Delay Alarm Transmission Timer ee ee ee e e e ee EER ER ER EER Ee Ee 15 Function Keys Installer eceesiiiiiesiriieeeerrirerrrrineeserns 33 Delay Between Dialing Attempts esee 28 Delayed 24Hr Fire Zone cccee eene 14 G Delinquency Timer Closing cem 29 G
101. ell On Communication Fal 30 Keypad Beep on Successful Arm or Disarm Report 30 Dial Tone Delay cocineta N 30 PROGRAMMABLE OUTPUTS ee en 31 PGM Activation Event 31 PGM Deactivation Option sese eee ee eee e 31 Flexible PGM Deactivation Option 31 PGM Deactivation Event 31 POM Timer is ae RB RE AE EE 31 PGM1 Becomes a 2 wire Smoke Detector Input 31 PGM Test Mode hewn di aaa iain 31 SYSTEM SETTINGS AND COMMANDS 32 HafdwareReset derisa td entis 32 Software Reset ie ee ee ee ee Ee iai nana 32 Installer Code LOCK es ee ke ee ee AR AA Re ee Ak 32 DIGIPLEXNE CONTROL PANEL 1 Daylight Savings Time 32 Ae IER 42 Battery Charge Current 32 Stay d le EE 42 Comb s Speed EER iic e e eic De 32 EER AE hte o ier ENG 42 Transmit Zone Status on Serial Pont 32 Force Arming sic ir ee edt det e e d crees 42 Serial Port Baud Hate 32 PIOW 10 AIM Sas rd dae ete dta aetas 42 Tail eN a 32 DISARMING EE N c RE HE EA N 42 Shabbat Feature T 33 Bypass Programming sse eee eee eee eee eee eee 42 Installer Function Keys sees eee eee eee 33 GhirmeZOones eui eR Ue iR a ede stes 43 Module Reset esee 33 Keypad Settings AE AR RE RC EER E 43 Locate Module EE EER EE RE deeg 33 Event Record Display 43 Module Programming senem 33 Scroll Resta iii ttam Module and Label Broadcast iese ee ee Re Re ee 33 Trouble Display System D
102. enied 000 001 to 032 001 to 032 051 Door Left Open Alarm 255 z any Door Door Numbers 001 to 032 001 to 032 052 Door Forced Alarm Number 001 to 032 001 to 032 053 Door Left Open Restore 001 to 032 001 to 032 t See page 51 See page 50 48 REFERENCE amp INSTALLATION MANUAL Event Group Event Door Forced Open Restore Feature Group 000 255 z any Door Number Feature Door Numbers Start 001 to 032 End 001 to 032 055 Intellizone Triggered 000 Zone Numbers 001 to 096 001 to 096 255 Any zone number Not Used Not Used 056 to 061 Future Use Future Use Future Use Future Use Future Use Access Granted to User 000 User Codes 001 to 255 001 to 255 001 to 255 001 User Codes 256 to 511 000 to 255 000 to 255 002 User Codes 512 to 767 000 to 255 000 to 255 003 User Codes 768 to 999 000 to 231 000 to 231 255 Any User Code Not Used Not Used Access Denied to User 000 User Codes 001 to 255 001 to 255 001 to 255 001 User Codes 256 to 511 000 to 255 000 to 255 002 User Codes 512 to 767 000 to 255 000 to 255 003 User Codes 768 to 999 000 to 231 000 to 231 255 Any User Code Not Used Not Used Status 1 Status 2 See NOTE 1 on page 50 See NOTE 1 on page 50 Armed 000 000 Force Armed 001 001
103. entification codes and re establish communication When the control panel hangs up WinLoad automatically goes into Wait For Call Mode see WinLoad s Online Help ready to answer when the control panel calls back The PC Telephone Number must be programmed see section 14 3 14 5 CALL WINLOAD Dial the PC Telephone Number programmed in section 3010 to communicate with WinLoad The control panel and WinLoad verify that the Panel Identifier and the PC Password match before establishing communication WinLoad must be in Wait For Call Mode see WinLoad s Online Help For LCD Keypads Press and hold the 0 key enter your INSTALLER CODE and then press FORCE For Grafica Keypads Press and hold the 0 key enter your INSTALLER CODE press the center action key Options highlight Call WinLoad and then press the left action key Select 14 6 ANSWER WINLOAD To perform on site uploading downloading connect the computer directly to the control panel using an ADP 1 line adapter In WinLoad set Dialing Condition to Blind Dial Program the PC telephone number in WinLoad and follow the ADP 1 Adapter s instructions When the computer has dialed For LCD Keypads Press and hold the 0 key enter the INSTALLER CODE and press ARM to manually answer WinLoad from the panel Press DISARM to hang up For Grafica Keypads Press and hold the 0 key enter the INSTALLER CODE press the center action key Options highlight A
104. er by having the keypad beep 10 times and or by squawking the bell 10 times The user should leave immediately and contact the Monitoring Station from a secure location Select the section that corresponds to the desired partition and enable or disable the desired option off disabled 6 16 2 No Exit Delay on Remote Arm Default enabled When a user arms by using a remote control from the Omnia Wireless System OMN RCV3 the control panel will cancel the Exit Delay and immediately arm the partition Enable option 8 in the desired section Partition 1 3124 Partition 3 3324 Partition 5 3524 Partition 7 3724 Partition 2 3224 Partition 4 3424 Partition 6 3624 Partition 8 3824 Partition 1 3125 Partition 3 3325 Partition 5 3525 Partition 7 3725 Partition 2 3225 Partition 4 3425 Partition 6 3625 Partition 8 3825 Option Bell Squawk on Description Bell or siren emits 10 squawks BEI Bell Pino back default disabled Keypad emits 10 beeps 8 Keypad Ring back default enabled 6 17 KEYPAD LOCK OUT FEATURE Default 000 If a consecutive number of invalid codes are entered into a keypad the control panel can be set to lockout access from all the keypads in the partition for a specified period Program the number of consecutive invalid codes from 001 to 255 000 disabled into the desired
105. es SOUNDER RELAY DISABLES 520 520 521 522 523 524 525 COMMUNICATION DISABLES 550 8 560 551 552 Sounder Relay Disabled Bell 1 Disable Bell 2 Disable Alarm Relay Disable Trouble Relay Disable Reversing Relay Disable Dialer Disabled Radio Transmitter Disabled BYPASSES 570 570 571 572 573 Zone Bypass Fire Bypass 24 Hour Zone Bypass Burg Bypass Group Bypass 600 Manual Trigger Test Periodic Test Report Periodic RF Transmission Fire Test Status Report to Follow Listen in to Follow Walk Test Mode Event Log Reset Event Log 50 Full Event Log 90 Full Event Log Overflow Time Date Reset Time Date Inaccurate Program Mode Entry Program Mode Exit Exception Schedule Change INDEX AA IA Sections A EE 19 Auto Arming Options TT 19 A Automatic Event Buffer Transmission esses 41 AC Failure not Displayed emnes 34 Automatic report code list ee ee ee ee RE RR Re ER raro nano ER ee ee 52 REES SE EE N AI N AE AR DE E E 4 Auxiliary Power RA EG 4 D ALMOST Mq 39 Calculating power consumption ER SEI Power Limitations sx ee ee ee ee ER RR ER men 6 EE EE EE 38 Power Supply Connections ee ee ee ee ee ee ek eek ee 7 euro Heri WEE 38 Troubles cai a ad gae 44 Access Card Assignment sss 37 Away Arming See Force Arming Access Code Length d TV d d daa dR NE a Tea ee 36 Away Zones See Force Zones Access Codes rece dert ve ee tuu
106. es 001 to 125 value x 008 40 008 to 1 second Subtracting Values 128 to 253 value 127 x 008 0 008 to 1 008 second Example Entering a value of 100 will add 800 100 x 008 seconds to the clock at the beginning of every hour Likewise entering a value of 200 will subtract 0 584 200 127 x 008 seconds from the clock at the beginning of every hour 11 18 REMOVE MODULE SECTION 4005 After entering section 4005 the control panel scans all modules on the combus If modules are missing i e module was removed during this Scan the control panel erases the module s serial number and removes the module from the control panel s memory 11 19 SERIAL NUMBER VIEWING SECTION 4000 Enter section 4000 to view the serial number of the control panel as well as the serial numbers of all modules on the combus For LCD Keypads After entering section 4000 the keypad will display the 8 digit serial number of the control panel Use the A and V keys to scroll through the serial number of each module connected to the combus For Grafica Keypads After entering section 4000 the keypad will display the 8 digit serial number of the control panel Press the center action key Next to scroll through the serial number of each module connected to the combus 11 20 PowER SAvE MODE SECTION 3033 OPTIONS 4 Default enabled When option 4 is enabled and the control panel is running on the b
107. ess Control Options and User Labels using a different method of programming SY f no partition assignment is selected the User Access Code will e only be able to activate PGMs To program user labels refer to the LCD Keypad System Manager s Manual or to the Grafica Graphic LCD Keypad Online Help 36 REFERENCE amp INSTALLATION MANUAL Figure 12 1 Programming User Access Codes Press amp hold Where sections 1002 to 1999 represent the 0 key User Access Codes 002 to 999 1 User Options Key in the 1 2 Feature INSTALLER off off Master Feature Disabled CODE on off User can program PIN on on User can program User Options Partition Assignment PIN and all Access Control options SECTION User Options Feature Select 3 Duress 6 Stay 8 Instant Programming 4 Bypass 7 Force 5 Arm Only 8 off Access keypad s partitions on Access user s partitions Note all users can regular arm Press nie A koy Partition Assignment 1 User Code has Access to Partition 1 User 2 User Code has Access to Partition 2 Partition 3 User Code has Access to Partition 3 Assignment 4 User Code has Access to Partition 4 Feature Select 5 User Code has Access to Partition 5 Programming 6 User Code has Access to Partition 6 7 User Code has Access to Partition 7 Press the A key 8 User Code has Access to Partition 8 Access Level amp Schedule Assignment First Brackets Access Level Enter Level from 00
108. event is generated see section 13 1 When option 2 is enabled the control panel can record the REX events generated from all the Doors in the Event Buffer but cannot report these events to the Monitoring Station The events can be viewed by entering the Event Record Display see section 15 10 Since REX events can occur often the Event Buffer may fill up quickly 13 18 2 Log Door Left Open Restore In Event Buffer SECTION 3038 OPTION 3 Default disabled Door Left Open Restore means that an Access Door closed after it was left open beyond a programmed Door Left Open Interval refer to the Digiplex DigiplexNE Access Control Module Reference amp Installation Manual When option 3 is enabled the Door Left Open Restore event can be recorded in the Event Buffer These events cannot be reported to the Monitoring Station but can be viewed by entering the Event Record Display see section 15 10 13 18 3 Log Door Forced Open Restore In Event Buffer SECTION 3038 OPTION 4 Default disabled Door Forced Open Restore means that an Access Door s door contact closes after it was opened without the use of a valid Access Card or User Access Code or receiving a Request for Exit signal When option 4 is enabled the Door Forced Open Restore event can be recorded in the Event Buffer This event cannot be reported to the Monitoring Station but it can be viewed by entering the Event Record Display see section 15 10 WIN LOAD SOF
109. f Input 03 Input 04 Input 16 ATZ of Input 04 Input 05 Input 17 ATZ of Input 05 Input 06 Input 18 ATZ of Input 06 Input 07 Input 19 ATZ of Input 07 Input 08 Input 20 ATZ of Input 08 Input 09 DGP2 ZX4 Input 01 Input 21 ATZ of Input 09 Input 10 DGP2 ZX4 Input 02 Input 22 ATZ of Input 10 Input 11 DGP2 ZX4 Input 03 Input 23 ATZ of Input 11 Input 12 DGP2 ZX4 Input 04 Input 24 ATZ of Input 12 4 3 ZONE DEFINITIONS The 16 zone definitions from Figure 4 1 on page 12 are described below When an alarm occurs the control panel can send a report activate the bell output and display the alarm in the Alarm Memory 4 3 1 Zone Disabled SECTIONS 0101 To 0196 FIRST DIGIT O Disables the corresponding zone Zones are disabled by default 4 3 2 Entry Delays 1 and 2 SECTIONS 0101 To 0196 FIRST DIGIT 1 AND 2 Default Entry Delay 1 030 Entry Delay 2 060 When an armed zone defined as an Entry Delay opens the control panel will not generate an alarm until the Entry Delay Timer elapses A zone defined as Entry Delay 1 follows the Entry Delay 1 Timer of its assigned partition Likewise a zone defined as Entry Delay 2 follows the Entry Delay 2 Timer of its assigned partition For example if zone 1 is assigned to Partition 5 and is defined as Entry Delay 1 the timer follows the amount programmed in 3511 Each partition includes two Entry Delay Timers To program an Entry Delay Timer key in the desir
110. fuseless circuit and will automatically shut down if the current exceeds 3A If the load on the BELL terminals returns to normal x3A the control panel will re instate power to the BELL terminals When connecting sirens please verify correct polarity as shown in Figure 2 3 PGM2 and PGM3 are relays rated at 5A each and can be used to power bells and or other warning devices by programming them as a bell siren outputs see section 10 on page 31 When the bell output is not used the Bell Absent message A appears in the Trouble Display To avoid this connect a 1kQ resistor across the bell output UL Note The keypads must be programmed to beep with all troubles 2 8 PROGRAMMABLE OUTPUTS The control panel comes standard with PGM1 to PGMS When a specific event or condition occurs in the system a PGM can be programmed to reset smoke detectors activate strobe lights open close garage doors and much more For details on how to program the PGMs refer to section 10 Figure 2 1 PGM amp Relay PGM1 is 100mA max normally open output PGM2 and PGM3 are 5A relay outputs that can be normally open or normally closed If the current draw on PGM1 is to exceed the current output we recommend using a relay as shown in Figure 2 1 PGM1 can be programmed as a 2 wire smoke detector input see section 2 17 1 on page 9 and section 10 6 on page 31 COM N C NO 2 9 KEYSWITCH CONNECTIONS nor VERIFIED BY UL Connect the keyswitches t
111. g on DOOF eee eee eee eee eee 40 Door Access During Clock Loss eee eee eee 40 Burglar Alarm On Forced Door or Door Left Open 40 Logging Access Control Events 40 WINLOAD SOFTWARE esse ees esse see ee es se ee ee EE ee en 41 Panel Identifier essen 41 delde BERE OE team e ee 41 PC Telephone Number 41 CallBack Features EE un voe mud eiie AE ig 41 Call Win Load EE tidad eren 41 Answer Wim oa 41 Answering Machine Override Delay sseeeeeeeeeeeeeeeeeeeeeeeeee 41 Ring COUNTE iie tes AE N 41 Event Buffer Transmission eee 41 USER FEATURES ncccocrcecec cocer pacc cada riada 42 2 REFERENCE amp INSTALLATION MANUAL INTRODUCTION oo DigiplexNE is a security and access control system with 8 on board zone inputs 16 with zone doubling that is expandable to 96 zones via the 4 wire combus DigiplexNE features up to 999 users 8 partitions 32 doors 32 schedules 16 access levels and can support up to 127 modules in any combination DigiplexNE systems provide the highest level of protection for banks high security military and government sites luxurious residential homes and any place where maximum security is essential These systems are designed to be easy to use and the modular concept of these systems provides installer s with labour saving features that make expanding installing and servicing these systems quick and convenient Expand the DigiplexNE sy
112. git CSTN 4 CSTN Central Station Telephone Number r Partition 1 Partition 2 Partition 5 I Partition 6 Partition 7 Partition 8 Dialing sequences for Arm Disarm Report Codes Partition 1 3127 Partition 5 3527 Partition 2 3227 Partition 6 3627 Partition 3 3327 Partition 7 3727 1 Call Central Telephone 1 Partition 4 3427 Partition 8 3827 2 Call Central Telephone 2 Figure 8 1 Event Reporting Reporting Account Number 1 Related Features 3 or 4 digits 0 F in Section 3061 Delay Before Alarm Transmission 3055 Reporting Account Number 2 Pager Format Delay Transmission 3057 3 or 4 digits 0 F in Section 3062 Recent Closing Delay S Sections 3109 3209 3309 3409 T Reporting Account Number 3 35091 3609 3709 and 3809 Partition 3 3 ar 4 digits 0 F in Section 3063 Lede EEE 209 A0 EE ESE EE Power Failure Report Delay 3058 Reporting Account Number 4 Auto Test R 804 d 3041 Partition 4 9 lt or 4 digits 0 F in Section 3064 uto Test Report 3040 anp 3041 Report Disarm Options Reporting Account Number 5 Option 7 Sections 3123 3223 3323 3 or 4 digits 0 F in Section 3065 3423 3523 3623 3723 and 3823 Report Zone Restore Options Reporting Account Number 6 P E Section 3037 Option 8 3 or 4 digits 0 F in
113. hat User Access Codes can open the doors in their assigned Access Level see section 13 6 In ON ON SH E GE th Access Mode see section 13 10 Enable or disable the options as M 9 yP required for each Access Card as shown in Figure 12 1 Master Code has access to Access Control features PINs and User Labels ET A user that is not assigned to any partition but has the access A Duress enabled User Access Code can arm control user option 1 enabled Access Control can now gain 3 Duress or disarm the partition and can immediately access to an access control door by entering a code PIN and transmit a silent alarm to the Monitoring Station then pressing the acc keypad button 4 Bypass User can program bypass entries as Option Feature Description aaa e IN s tois f ON User s Access Control feature is 5 Arm Only aa arm assigned partitions but cannot enabled and user has access when the control panel s Access Control feature is enabled 6 Stay or Instant User can Stay Arm or Instant Arm see section n Re OFF User s Access Control feature is Arm 15 2 assigned partitions disabled but the User Access Code remains unaffected This can be used to disable a lost or stolen card without deleting the User Access Code Card can unlock Door and disarm assigned partitions User Option 5 Arm Only must be disabled for this feature to function Card uses the Door Unlocked Period Extension feature see DGP2 ACM1P s Refe
114. he Account Number Transmission see section 8 6 on page 27 corresponds to the partition the control panel only uses the Partition 1 Account Number programmed in section 3061 but the report code includes the partition number Only the SIA format supports the 0 lt 0 digit in its account 8 6 ACCOUNT NUMBER TRANSMISSION SECTION 3035 OPTION 6 Default Partition Account Option 6 determines whether the account number that is sent to the central station corresponds to a partition or to a central station telephone number CSTN With option 6 enabled the account number that is sent to the central station corresponds to the CSTN that was dialed Regardless of which partition the report originated from the account number for the corresponding CSTN will be transmitted instead of the corresponding partition account number For example a report originating from partition 8 is transmitted to CSTN 1 Although the report originated from partition 8 Account Number 1 see Table 4 on page 26 is transmitted with the report With option 6 disabled the account number that is sent to the central station corresponds to the partition where the event originated regardless of which CSTN is dialed For example a report originating from partition 8 is transmitted to CSTN 1 The account number that is transmitted to CSTN 1 is Account Number 8 see Table 4 on page 26 8 7 REPORTING FORMATS SECTION 3070 The control panel can use a
115. he Utility Key Event corresponding to the desired keyswitch see PGM Programming Table in the Programming Guide Event Group 048 2 Enable option 4 in the section corresponding to the desired keyswitch 5 3 KEYSWITCH PARTITION ASSIGNMENT SECTIONS 0601 To 0632 SECOND DIGIT 1 TO 8 The control panel provides the option of partitioning the security system into eight completely independent systems Therefore each keyswitch must be assigned to one partition as shown in Figure 5 1 on page 16 For details on Partitioning see section 11 9 on page 32 5 4 KEYSWITCH OPTIONS Each keyswitch zone can be programmed with one or more of the options below as shown in Figure 5 1 on page 16 5 4 1 Stay Instant Disarm Option Keyswitch SECTIONS 0601 To 0632 OPTION 4 When option 4 is enabled the keyswitch can only disarm assigned Stay or Instant Armed partitions The Arm Only Option see section 5 4 2 must be disabled for this feature to function When option 4 is disabled the keyswitch can disarm partitions armed using any arming method 5 4 2 Arm Only Keyswitch SECTIONS 0601 To 0632 OPTION 5 When option 5 is enabled the keyswitch can arm assigned partitions but cannot disarm any partitions The type of arming is determined by the other Keyswitch Options selected 5 4 3 Regular Arming Keyswitch SECTIONS 0601 TO 0632 OPTION 6 To 8 When options 6 to 8 are disabled the keyswitch arming option
116. his equipment must be verified by a qualified technician once every three years All keypads must use a tamper switch Maximum allowed entry delay is 45 seconds Maximum allowed exit delay is 60 seconds Minimum 4 minutes for bell cut off time The following features do not comply with UL requirements Bypass Recall Shabbat Auto Trouble Shutdown and No AC Fail display N Do not connect the primary indicating device to a relay The installer must use the bell output All modules installed on the system must be UL listed in accordance with the standards listed above N The metallic enclosure must be grounded to the cold water pipe The DGP2 ZX4 is not approved for UL systems For further details concerning the above information refer to the UL standards listed and or the Underwriters Laboratories Inc Standard for Safety s Installation and Classification of Burglar and Holdup Alarm Systems Recommended N EOL resistor part 42011002000 N Transformers A ATC Frost FTC3716 16 5Vac 37VA B ATC Frost FPS4016 16 5Vac 40VA C Basler Electronics model BE156240CAA 16 5Vac 50 60Hz 20VA or 40VA For CSA listed systems use Basler Electronics transformer model BE116240AAA N 12Vdc 4Ah rechargeable acid lead or gel cell backup battery YUASA model NP7 12 recommended for residential use 7Ah battery to comply with fire requirements All outputs are Class 2 or power limited except for the battery terminal The Class
117. ing Mode AAA 11 ZONE PROGRAMMING esse esse ss sees see ee ereenn nenen 12 Zone Numbering TT 12 Zone Doubling AT 13 Zone BE GE ER EE ER EE 13 Zone Partition Assignment AAA 14 Zone SERE EA EE Leder ER 14 Input Speed ses re Ee Rv pice Se aati 15 EOL on Hardwire Zones 15 Keypad Numbering AAA 15 KEYSWITCH PROGRAMMING 16 Keyswitch Numbering eese 16 Keyswitch Definitions AA 16 Keyswitch Partition Assignment AAA 17 Keyswitch Options sss see eee 17 ARMING AND DISARMING OPTIONS 18 Arming Follows Partition sss sees eee eee eee eee eee eee eee 18 Restrict Arming on Supervision Loss ee eee eee ke ee 18 Restrict Arming on Tamper esse eee eee eee eee eee eee 18 Restrict Arming on AC Falure see 18 Restrict Arming on Battery Failure A 18 Restrict Arming on Bell or Auxiliary Failure 18 Restrict Arming on TLM Failure sss see eee eee eee eee 18 Restrict Arming on Module Troubles sssss 18 Timed Auto Arming eese 18 No Movement Auto Arming eene 19 Auto Arming Options esee 19 Switch To Stay Arming sese ee eee ee eee eee 19 Always Force Arm when Regular Arming 19 Follow Zone Switches to Entry Delay 2 ssse 19 One touch Features cel e d ts 19 Squid 19 Keypad Lock out Feature sees eee ee ee ee eee 20 Be
118. ion Feature 5 6 OFF OFF Steady Alarm Description sends the report code and activates the bell output sends the report code and pulses the bell output see Figure 4 4 on page 14 OFF ON Silent Alarm sends the report code but the bell output is not activated Partition must be disarmed sends the report code Disarming is not required ON ON open ONY Fire Zones cannot be Report Only ON OFF Pulsed Alarm 4 5 6 Intellizone SECTIONS 0101 To 0196 OPTION 7 Default 010 If an alarm condition occurs on a zone with option 7 enabled the control panel triggers the Intellizone Delay and seeks confirmation of the alarm situation before generating an alarm Fire Zones cannot be set as Intellizones An alarm will only be generated if one of the following conditions occurs during the Intellizone Delay 1 An alarm occurs on another zone defined as Intellizone 2 The zone in alarm restores and reoccurs 3 The zone stays in alarm for the entire Intellizone Delay Key in the desired 3 digit delay value 010 to 255 seconds into the section corresponding to the desired partition 000 10 seconds Partition 1 3110 Partition 3 3310 Partition 5 3510 Partition 7 3710 Partition 2 3210 Partition 4 3410 Partition 6 3610 Partition 8 3810 UL Note For UL Listed systems the detection pattern of both zones shall be installed so that each zone has
119. iption Resets the programmable sections from 0001 to 3991 to default even if Installer Code Lock is enabled The Event Buffer Panel ID PC Password PC Telephone Number and Zone Door Partition and User Labels see section 12 4 will not reset 4040 4041 Resets the System Master Code to 123456 Resets all Zone Programming sections from 0001 to 0196 0201 to 0296 and 0961 to 0984 to default Resets the Access Control sections except Door Labels see section 11 24 from 2201 to 2712 to default Resets all User Access Code Programming sections from 1001 4044 to 1999 and 2001 to 2199 to default User Labels see section 12 4 will not be reset 4042 4043 Resets all control panel settings from 3020 to 3043 and from 3900 to 3991 and all the Dialer sections from 3051 to 3081 to default 4045 Resets all Partition Settings except Partition Labels see section 4046 24 from 3101 to 3829 to default 4047 Resets Keyswitch Programming sections from 0501 to 0832 and all Programmable Outputs sections from 0901 to 0939 to default Entering this section resets the User Labels from the User Access Codes the Zone Labels from 0301 to 0396 Door Labels from 2301 to 2332 Partition Labels 3100 3200 3300 3400 3500 3600 3700 and 3800 to default 4048 A Do not remove power from the control panel
120. l activate the PGM The Event Group specifies the event the Feature Group identifies the source and the Start and End sets the range within the Feature Group see PGM Programming Table in the Programming Guide For example the control panel can activate PGM1 when the partition is armed by User Access Codes 256 to 260 Therefore Event Group section 0910 010 Arming with User Code Feature Group section 0911 001 User Codes 256 to 511 Start section 0912 000 End section 0913 004 Enter the sections that correspond to the Event Group Feature Group Start 4 and End of the desired PGM and enter the desired 3 digit number from the PGM Programming Table Event Group Feature Group Start End PGM 1 0910 0911 0912 0913 PGM 2 0920 0921 0922 0923 PGM 3 0930 0931 0932 0933 10 2 PGM DEACTIVATION OPTION Once the PGMs are activated see section 10 1 they can deactivate when another event occurs or after a period of time The PGM Deactivation Option determines which method is used the PGM Deactivation Event see section 10 4 or the PGM Timer see section 10 5 Enter the section that corresponds to the desired PGM and enable or disable option 1 default PGM Deactivation Event PGM 1 0919 Option Feature PGM 2 0929 1 ON PGM Timer PGM 3 0939 1 OFF PGM Deactivation Event 10 3 FLExiBLE PGM DEACTIVAT
121. l panel will not send report codes for keyswitches that are defined with the PGM Activation definition 24 REFERENCE amp INSTALLATION MANUAL 8 2 5 Access Codes Arming SECTIONS 2001 To 2099 A report code can be programmed individually for each User Access Code from 01 to 98 in sections 2001 to 2098 User Access Codes from 99 to 999 use a common report code in section 2099 When an access code is used to arm a partition the control panel can send the report code to the Monitoring Station identifying which access code was used 8 2 6 Access Codes Disarming SECTIONS 2101 To 2199 A report code can be programmed individually for each User Access Code from 01 to 98 in sections 2101 to 2198 User Access Codes from 99 to 999 use a common report code programmed in section 2199 When an access code is used to disarm a partition the control panel can send the report code to the Monitoring Station identifying which access code was used The report code can be transmitted when a partition is disarmed or only when disarmed following an alarm Also see section 8 13 8 2 7 Special System Reporting Codes When the system generates one of the following events the control panel can send the report code to the Monitoring Station identifying the event Section Event Description 3900 Cold Start control panel re starts after complete shutdown total power loss 3901 Warm Start control panel resets due t
122. le Tolerance Window applies to the Arming and Disarming Report Schedules only section 8 3 1 and section 8 3 2 The Arming Disarming Schedule Tolerance Window does not apply to Access Schedules section 13 6 A 8 4 MONITORING STATION PHONE SECTIONS 3071 To 3074 The control panel can dial up to 4 different Monitoring Station telephone numbers Sections 3071 to 3074 represent Monitoring Station telephone numbers 1 through 4 Enter any digit from 0 to 9 and any special keys or functions see Table 3 up to a maximum of 32 digits Refer to Event Call Direction in section 8 8 and Reporting Formats in section 8 7 for details on how these telephone numbers are used Table 3 Special Telephone Number Keys Function LCD Grafica p sTAY FORCE Switch to Tone Dialing T ARM EE e Wait for second dial tone W DISARM appears 4 second pause P BYP Insert MEM Delete TRBL Delete from cursor to end acc Left action key Clear 8 5 ACCOUNT NUMBER SECTIONS 3061 TO 3068 Default 000 All report codes are preceded by a 3 or 4 digit Account Number to ensure correct identification of system events The Account Number that is transmitted with the report code can correspond either to the partition or to the central station telephone number see section 8 6 on page 27 Account Numbers can be any hexadecimal value from 0 to F Table 4 Account Numbers
123. led can Instant Arm a partition Refer to How to Arm on page 42 for information on how to Instant Arm the System 15 3 1 Instant Arming with Delay Instant Arming with Delay functions like Instant Arming except armed zones are programmed with an Entry Delay Timer see section 4 3 14 If a zone is triggered the delay starts allowing the user time to disarm the partitions 15 4 FoRCE ARMING Force Arming allows the user to arm a partition when Force zones are open see section 4 5 4 Once the open zone in an armed partition is closed the system will then arm it as well This feature is commonly used when a motion detector is protecting an area that is occupied by a keypad The system can also be Force Armed by using a One touch Feature see section 6 15 or a Keyswitch see section 5 4 5 Only User Access Codes with the Force Arm option enabled can Force Arm a partition For example during Force arming the motion detector remains unarmed until the user exits the area The system will then arm the motion detector Refer to How to Arm on page 42 for information on how to Force Arm the system 15 5 How TO ARM The following section details how to arm the system using an LCD or Grafica keypad For LCD Keypads To arm users 1 Enter their ACCESS CODE 2 Press the key corresponding to the desired arming method see Table 13 on page 42 If the users have access to more than one partition they can press the key s corresponding
124. ll SqUaWK TTT 20 FRING DACK TTT 20 Maximum Bypass Entries AA 20 Display Bypass If Armed AAA 20 ALARM OPTIONS 1 uere ennenen 21 Bell alarm Output cin ee retenti 21 Bell Cut off Timer ii aee eene 21 Wireless Transmitter Supervision Options 21 Police Code Timer circ center 21 Tamper Recognition Options sees ee eee ee ee ke ee ee 21 Keypad Panic Options eene 22 EVENT REPORTING ennenen enen 23 Reporting Enabled sssseesssersseessseeeser eser enrere reenn nne 24 Report Codes i mt detect etc EE Ge DE EE teneas 24 Report Arming and Disarming sese eee eee eee eee eee ee 25 Monitoring Station Phone H 26 Account Number ees ee ee ee Re Re ee ee ee 26 Account Number Transmission sss see eee eee eee Re ee 27 Reporting H ec n C 27 Event Call Direction is EE enee teeta ed 27 Pager Delay voii 28 Recent Close Delay AA 28 Power Failure Report Del 28 Auto Test Reportar inician 28 Disarm Reporting Options sese ee eee ee ee ee eee 28 Zone Restore Report Options sss eee eee 28 Auto Report Code Programming sss sese sese ee eee eee 28 Closing Delinquency Timer eee 29 DIALER OPTIONS n ennenen see De n Bee Ge Ed 30 Telephone Line Monitoring AA 30 Tone pulse Dialing AN 30 Pulse Ratio oe ree giro od go 30 Busy Tone Detection ee ee ee eese 30 Switch To PISE ie ER EER eerte treten ries 30 B
125. ll answer after three rings 14 8 RiNG COUNTER SECTION 3051 Default 008 The Ring Counter represents the number of rings the control panel will wait before picking up the line If the line is not answered after the number of programmed rings the control panel answers the call If more than 10 seconds pass between each ring the Ring Counter resets Also see section 14 7 Enter any value between 01 to 15 00 disabled to determine the number of rings 14 9 EvENT BUFFER TRANSMISSION SECTION 3037 OPTION 2 Default disabled Once the Event Buffer contains 1998 events since the last upload the control panel makes two attempts to establish communication with a computer using WinLoad by calling the PC Telephone Number programmed in section 3010 WinLoad must be in Wait To Dial mode When communication is established the control panel uploads the contents of the Event Buffer to WinLoad If communication is interrupted before completing transmission or communication is not established after two attempts the control panel wait until the Event Buffer receives another 1998 events before attempting Event Buffer Transmission When the Event Buffer is full each subsequent new event will erase the oldest event in the buffer The Event Buffer can hold 2048 Events DIGIPLEXNE CONTROL PANEL 41 USER FEATURES E 15 1 REGULAR ARMING This method is used for the everyday arming of the system All zones within the partition must be
126. ly 1 1 FEATURES Digital combus Provides constant power supervision and two way communication between the control panel and all its modules Supports up to 127 modules Connect modules up to 3000ft 914m from the panel e Sabotage proof technology without additional wiring 96 addressable zones 8 partitions 998 user codes 1 System Master code and 1 installer code Built in access control 2048 stored events 1 telephone line and optional secondary telephone line Remote diagnostics and pager messaging False alarm prevention features 32 independent keyswitch zones does not use any of the 96 zones 8 on board hardwired input terminals 3 on board fully programmable outputs PGMs 1normally open high current transistor output 100mA 2normally open or normally closed 5A programmable relay outputs Up to 32 more PGM inputs through the Keyswitch s PGM Input feature PGM1 can be set as a two wire smoke detector input Event reporting aseparate dialing sequence for each partition 4Monitoring Station Telephone Numbers SIA Contact ID Ademco Contact ID Edition 2000 Pager Format and many more communicator formats 941990000000 1 2 SPECIFICATIONS CONTROL PANEL Non UL SYSTEMS AC Power 16Vac 20 40VA 50 60Hz Battery 12Vdc 4Ah minimum Auxiliary Power 12Vdc 600mA typical fuseless shutdown at 1 1A 1A fuseless shutdown 3A PGM Output PGM1 100mA PGM2 and PGM3 5A relay Event Buffer 2048 events All control
127. m either the Automatic Report Code List on page 52 or the Contact ID Report Code List on page 54 8 7 4 Ademco Contact ID Ademco Contact ID is a fast communicator format that uses tone reporting instead of pulse reporting It also uses a pre defined list of industry standard messages and report codes that will suit most basic installation needs To manually program the report codes use the 2 digit hexadecimal values from the Contact ID Report Codes List in the Programming Guide Enter 00 to disable reporting or FF to use the default report code from the Automatic Report Code List in the Programming Guide To automatically program a set of default Contact ID codes refer to section 8 15 8 7 5 SIA FSK SIA FSK is a fast communicator format that uses tone reporting instead of pulse reporting This communicator format uses a pre defined list of industry standard messages and report codes that will suit most basic installation needs To manually program the report codes enter 00 to disable reporting or any other value to use the default report code from the Automatic Report Code List in the Programming Guide To automatically program a set of default SIA FSK codes refer to section 8 15 8 7 6 Pager Reporting Format Using this format allows the control panel to transmit report codes to a pager A pound symbol is automatically generated after the report code Also refer to Pager Delay in section 8 9 8 8 EVENT CALL DIRECTION As shown i
128. n off disabled Partition 1 Option 1 Partition 5 Option 5 Partition 2 Option 2 Partition 6 Option 6 Partition 3 Option 3 Partition 7 Option 7 Partition 4 Option 4 Partition 8 Option 8 7 2 BELL CUT OFF TIMER Default 2 004 After an audible alarm the bell or siren will stop once the partition is disarmed or when the Bell Cut Off Timer has elapsed Enter any value between 001 and 255 minutes Partition 1 3113 Partition 3 3313 Partition 5 3513 Partition 7 3713 Partition 2 3213 Partition 4 3413 Partition 6 3613 Partition 8 3813 7 2 1 No Bell Cut Off on Fire Alarm SECTION 3030 OPTION 2 Default disabled The control panel can disable the Bell Cut Off Timers when alarms are generated from zones defined as Standard or Delayed Fire Zones see section 4 3 The BELL output will remain enabled until a user disarms the partition in alarm 7 2 2 Recycle Alarm Rate Default 000 The control panel re verifies the zone status during an alarm at a programmed rate once the Bell Cut Off Timer and the Recycle Delay elapse If open zones remain the control panel will regenerate the alarm Enter the number of times from 001 to 255 000 no limit in one armed period that the control panel will re verify the zone status Partition 1 3117 Partition 3 3317 Partition 5 3517 Partition 7 3717 When disarmed Gener
129. n Figure 8 1 on page 23 the control panel events are divided into three event groups for each partition and two global event groups Each event group can be programmed to dial up to four Monitoring Station telephone numbers with one used as a backup The numbers are dialed sequentially starting from 1 skipping any disabled numbers and stopping once all selected telephone numbers have been reached If the control panel still fails to report to a Monitoring Station telephone number after reaching the Maximum Dialing Attempts see section 8 8 1 the control panel will dial the selected backup telephone number unless the Alternate Backup Option is enabled see section 8 8 3 When the Alternate Backup Option is enabled the control panel will dial the backup number after every failed attempt For each section enable or disable the options Dialing sequence for Troubles and Restore Troubles 3080 Dialing sequence for Special System Arming Disarming and Alarm Reporting 3081 Dialing sequence for Access Code and Keyswitch Arming and Disarming Partition 1 3127 Partition 3 3327 Partition 5 3527 Partition 7 3727 Partition 2 3227 Partition 4 3427 Partition 6 3627 Partition 8 3827 Dialing sequence for Zone Alarms and Alarm Restores Partition 1 3128 Partition 3 3328 Partition 5 3528 Partition 7 3728 Partition 2 3228 Partition 4 3428 Partition 6 3628 Partition 8 3828
130. n hehe 36 Access Control LT ceo ade dd ada 37 B Access Control Terms via ER RII o 38 Backlightizi o t rete ete ve ve E e eee Ee hike Y Drusus 43 Access Denied See EE RR AN tv Ze eae REDE anaes RE Me gee 38 Backup Schedule ies Z dd eroe e ER ee Eg deed ve ode n 39 Access Granted EE EE e a N e E eae tna 38 BN ii ur e ener A exu Le he Fe en aate 4 A erm 38 Battery Test see see ER EER EE EER EE EER EE ER WE EER nennen inna 4 Access Level Assignment eie en 37 Battery Charging Current EEN 32 Account NUITDeFs cds EER N Ge dete ve tct De De Ge 26 A 32 Account Number Transmission eee eene 27 Bell Activate Card uester ede idet att ge we ee GE os did duet 37 pan Di Kee K E EE EE K Add Tolerance Windows to Schedules ens 37 Edi dran Quo Due Pe An AR Lo Ademco Contact Diao zesg aei qm i deed n er ec ie d te Data 27 CT he ch E AE N 4 Ademco EXPTE aa 27 TrOUDIes EE eee E ve hn deed Sat 43 Ademco SlOW i n cte te add e oda d CHR RC a ad t dr ia M AR 27 Bell Current Limit Trouble Clearing essen 44 Advanced Technology Zoning AT Z A 13 Bell On Communication Fal 30 Alarm Bell SquawK hee ei e ee epe ree ER ty deca Cel ere XR 20 On Door Left Coen ENEE 40 Bell alarm O tput rere edere oie e Tats c dete t 21 On Forced DOOF reer ge oe EE sea ee meii at due Ge s dra a 40 E MEAE MPEG MP 33 Alarm Transmission Delay See Delay Alarm Transmission Burglar Alarm ecce reset OR OE real ta edd woes 38 ULLE EE 15 Burglar Alarm on Doo
131. nect a small group of modules including a keypad to the combus Step 3 Connect the battery and then connect the AC power Enter section 4000 to verify if all the connected modules serial numbers appear see section 11 19 on page 34 If all the modules appear in section 4000 only the Clock Loss trouble and or Bell Absent trouble should appear on the keypad Verify the connection if a module does not appear in section 4000 or if a module trouble occurs Step 4 If another group of modules needs to be connected disconnect AC power and the battery and then continue the installation by following steps 2 3 and 4 Step 5 If modules were removed from the combus enter 4005 to remove them from the panel s memory see section 11 18 on page 34 Step 6 Connect an LCD Keypad at various points farthest from the control panel and use the keypad s built in Voltmeter to verify the combus s voltage refer to the Digiplex DigiplexNE LCD Keypad Reference amp Installation Manual 2 2 LOCATION amp MOUNTING Before mounting the cabinet push the five white nylon mounting studs into the back of the cabinet Pull all cables into the cabinet and prepare them for connection before mounting the circuit board into the back of the cabinet Select an installation site that is not easily accessible to intruders and leave at least 2 around the panel box to permit adequate ventilation and heat dissipation The installation site should be dry and clo
132. nection of terminal equipment Standard jacks shall be so arranged that if plug connected thereto is withdrawn no interference to operation of equipment at customer s premises which remains connected to telephone network shall occur by reason of such withdrawal INCIDENCE OF HARM Should terminal equipment protective circuitry cause harm to telephone network telephone company shall where practicable notify customer that temporary disconnection of service may be required however where prior notice is not practicable the telephone company may temporarily discontinue service if action is deemed reasonable in circumstances In case of temporary discontinuance telephone company shall promptly notify customer and will be given opportunity to correct the situation CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES The telephone company may make changes in its communication facilities equipment operations or procedures where such actions are reasonably required and proper in its business Should any such changes render customer s terminal equipment incompatible with the telephone company facilities the customer shall be given adequate notice to effect the modifications to maintain uninterrupted service GENERAL This equipment shall not be used on coin telephone lines Connection to party line service is subject to state tariffs RINGER EQUIVALENCE NUMBER REN The REN is useful to determine the quantity of devices that you may connec
133. nswer WinLoad and then press the left action key Select To hang up highlight Cancel Communication and then press the left action key Select 14 7 ANSWERING MACHINE OVERRIDE DELAY SECTION 3052 Default 008 If WinLoad will be used to communicate with an installation that uses an answering machine or service program the Answering Machine Override If the installation is called back within the programmed delay period the Answering Machine Override will bypass the answering machine or service by picking up the line on the first ring Also see section 14 8 In section 3052 program a value 00 to 15 X 4 seconds 00 disabled representing the delay period the control panel will wait between the first and second call To use Step 1 Using WinLoad call the installation and on the second ring press the ENTER key on the keyboard to hang up or hang up manually Step 2 After hanging up WinLoad will immediately call the installation back or call the site back manually For example an answering machine is set to answer after three rings and section 3052 is programmed with 10 10 x 4 2 40 seconds During the first call with WinLoad wait two rings and press ENTER WinLoad will immediately call the site back If the second call is made within 40 seconds the control panel will pick up the line on the first ring If it takes more than 40 seconds the control panel will not answer on the first ring and the answering machine wi
134. ntrol panel to answer a call SM made by the Central Monitoring Station that is using WinLoad CANCEL COMMUNICATION Cancels all communication with para the Monitoring Station or WinLoad until the next reportable event INSTALLER TEST MODE Perform walk tests where the bell or siren sguawks once when a zone opens and twice when it closes Press MEM again to exit Partitions cannot be armed if the Installer Test Mode is enabled MEM START MODULE SCAN Verifies the status of modules on the combus The LCD Keypads display the serial number of each module connected to the combus TRBL START VOLTMETER READING DGP2 641 only Verifies if the acc combus is supplying sufficient power at the keypad s location refer to the LCD Keypad Reference amp Installation Manual 11 12 MODULE RESET SECTION 4001 To reset a module connected to the combus to its default values key in the module s serial number into section 4001 11 13 LocATE MODULE SECTION 4002 To locate a specific module on the combus key in the module s serial number into section 4002 The green LOCATE LED on the module flashes until the serial number is re entered into the section or the module s tamper or unlocate switch is pressed 11 14 MoDULE PROGRAMMING SECTION 4003 All modules connected to the combus are programmed through the control panel To program a module enter section 4003 to enter Module Programming Mode
135. o section 2 17 1 on page 9 UL Note Not verified by UL 10 7 PGM TEST MODE Entering sections 0901 to 0903 activates the corresponding PGM for 8 seconds to verify if the PGM is functioning as desired PGM 1 0901 PGM 2 0902 PGM 3 0903 DIGIPLEXNE CONTROL PANEL 31 SYSTEM SETTINGS AND COMMANDS 11 1 HARDWARE RESET A Hardware Reset sets sections 0001 to 3991 to default including the Installer and System Master Codes Only the Panel ID PC Password PC Telephone Number and Event Buffer are not reset A Hardware Reset cannot be performed on a control panel with the Installer Code Lock enabled see section 11 3 1 Make sure the Installer Code Lock is disabled 2 Remove the battery and AC power from the control panel 3 Place the RESET jumper on the reset pins of the control panel 4 Re connect the AC power and the battery to the control panel 5 Wait 10 seconds and remove the jumper 11 2 SOFTWARE RESET Performing a software reset will set certain parameters to default values or program certain sections with a set of pre defined values To do so 1 Place the RESET jumper on the reset pins of the control panel 2 Enter Panel Programming Mode see section 3 4 3 Enter the 4 digit SECTION of the software reset you wish to perform Section Descr
136. o sudden problem other than power loss report generated automatically 3902 Test Report see section 8 12 3903 to 3904 Future Use control panel ends communication with 3905 WinLoad Log Off WinLoad 3906 Installer In installer enters programming mode 3907 Installer Out installer exits programming mode 3908 to 3909 Future Use 8 2 8 Special Arming Report Codes When the partition arms using a special arming feature the control panel can send the report code identifying how the system was armed Section Event Description 3910 Auto Arming when Auto Arming see section 6 9 3911 PC Armin system armed using WinLoad or NEware 9 software 8912 Late to Close when Auto Arming see section 6 9 3913 No Movement when No Movement Auto Arming see section 6 10 when partitions are Stay Instant or Force 90 Partial Arming Armed or armed with bypassed zones e partitions armed with a One Touch Arming 5915 ule Arming feature see section 6 15 partition armed before Arming Report setel Early to Gigas Schedule see section 8 3 2 partition armed after Arming Report Bata SO HES Schedule see section 8 3 2 partition armed with the InTouch Voice 3918 Remote Arm Assisted Arm Disarm Module APR3 ADM2 Partition hasn t been armed before the 3919 Closing Delinquency programmed Closing Delinquency Timer elapsed see section 8 16 8 2 9 Special Disarming
137. o the keypad control panel or Zone Expansion Module s hardwired input terminals as shown in Figure 2 2 Once a keyswitch is connected it must be assigned a keyswitch zone and its parameters must be defined as described in Keyswitch Programming on page 16 Figure 2 2 Keyswitch PANEL TERMINALS 2 10 AccEss CONTROL CONNECTIONS For all access control explanations and connection drawings refer to Access Control System Features on page 38 Figure 2 3 DigiplexNE Control Panel Wiring Diagram Red LINE 1 and LINE 2 LEDs Illuminated If the control panel is using a telephone line the panel will display which line it is using by illuminating a telephone line LED If the control panel is using Line 1 the LINE 1 LED will be illuminated If the control panel is using Line 2 the LINE 2 LED Red STATUS LED Flashing Indicates proper operation Fast Flash Indicates a control panel failure Off Control panel error will be illuminated Built in RTC See also the MEM KEY TM1 connector warning Charging and battery test LED every 64 seconds SERVICE AUX AUX Four pin connector can be used for quick installation of a keypad or module 92 x0opeJgd CAUTION Disconnect A the battery before replacing the fuse Optional connector can be used to recharge another battery in the system or to the connect a secondary battery WARNING AN moere connection may result in damage to
138. ode sent In the section that corresponds to the desired partition program the Start Time and End Time according to the 24 hour clock and enable the options representing the desired Days When option 8 is enabled access is permitted during the programmed holidays see section 13 8 Arming Report Schedule Partition 1 3102 Partition 2 3202 Partition 3 3302 Partition 4 3402 Partition 5 3502 Partition 6 3602 Partition 7 3702 Partition 8 3802 Disarming Repor t Schedule Partition 1 3103 Partition 3 3303 Partition 5 3503 Partition 7 3703 the System Manager s Manual have the number of minutes programmed in these sections added before and after the corresponding partition s schedule This allows certain individuals more flexibility without modifying all the Schedules For example using Figure 8 2 in section 8 3 2 if 015 is programmed in section 3104 users with Add Tolerance Windows to Schedules enabled on their cards can disarm between 8 35 and 9 25 and can arm between 16 40 and 17 45 without the control panel sending the report codes Enter any value between 001 and 255 to determine Arming Disarming Schedule Tolerance Window in minutes Partition 1 3104 Partition 3 3304 Partition 5 3504 Partition 7 3704 Partition 2 3204 Partition 4 3404 Partition 6 3604 Partition 8 3804 The Arming Disarming Schedu
139. odified to suit the installation s needs Each label contains a maximum of 16 characters For example change section 0301 ZONE 01 to FRONT DOOR When System Labels are modified the label is changed throughout the System The labels can be changed to reflect the location of the device or area to enable users and installers to rapidly understand the information displayed on the LCD screen To re program the System Label enter the desired section and use Table 6 Table 8 and Table 7 page 34 to modify the label To re program the System Labels in Hebrew or Russian enter the desired section and use Table 9 and Table 11 Hebrew or Table 10 and Table 11 Russian on page 35 For instructions on how to enter letters and special characters for the Grafica keypad refer to Grafica s Online Manual A complete Grafica Online Manual is available on our web site at www paradox ca Zone Labels Sections 0301 to 0396 represent Zones 01 to 96 Door Labels Sections 2301 to 2332 represent Doors 01 to 32 Partition Labels Partition 1 3100 Partition 3 3300 Partition 5 3500 Partition 7 3700 Partition 2 3200 Partition 4 3400 Partition 6 3600 Partition 8 3800 Table 6 Keys Press Feature Description sTAY Insert Space Inserts a blank space in the cursor s position Deletes the character or blank space found FORCE
140. ogram two zone expansion modules SN 34540075 and SN 34412100 with the same settings and options of zone expansion module SN 34540033 1 Press and hold the 0 key 2 Enter your INSTALLER CODE and then enter section 4004 3 Enter 34540033 34540075 and 34412100 and then press Acc The control panel automatically copies the contents of 34540033 into the other two zone expansion modules Label Broadcast Example Using a Grafica keypad to copy the labels of the control panel SN 020000A2 to all modules that support the labels 1 Press and hold the 0 key 2 Enter your INSTALLER CODE and then enter section 4004 3 Enter 020000A2 4 From the Destination screen press the center action key Start The control panel will automatically copy its labels to all supporting modules 11 16 SYSTEM DATE amp TIME The System Date and Time is programmed through the User Menu please refer to Clock Loss in section 15 12 DIGIPLEXNE CONTROL PANEL 33 11 17 CLOCK COMPENSATION VALUE SECTION 3050 Default Disabled When the DigiplexNE s clock is inaccurate a clock compensation value can be entered into section 3050 to correct the time drift At the beginning of every hour the control panel will either add or subtract the clock compensation value to from its clock Every value from 001 to 125 will add 0 008 seconds and every value from 128 to 253 will subtract 0 008 seconds from the clock 000 Disabled Adding Valu
141. ol panel see Zone Programming on page 12 Before connecting a module to the combus remove AC and battery power from the control panel 2 16 1 Connecting the Combus in Noisy Environments When installing the combus wires in proximity to high electrical interferences such as neon lights motors high voltage wiring transformers or if connecting the combus across separate buildings you must use shielded cables Connect the shielded cable as detailed below Within the Same Building Strip the outer jacket at one end of the shielded cable to expose the shield and connect the shield to the control panel ground not the dialer ground while leaving the shield at the other end of the cable open floating Across Separate Buildings Strip the outer jacket at one end of the shielded cable to expose the shield In the same building that houses the control panel connect the exposed shield to a cold water pipe or any other earth ground available while leaving the shield at the other end of the cable open floating The same configuration applies for any subsequent building 2 17 FIRE CIRCUITS Connect the smoke detectors using any of the following methods Assign the smoke detectors connected to the control panel or zone expansion input terminals to a zone and define the zone s parameters as a Fire Zone see section 4 on page 12 ISE becomes lec 255 2 17 1 Smoke Detector Installation 2 Wire PGM can be defined as a 2 wire Figure
142. ombus Input Terminals 1234567 8 z Zone Expansion Module 2 SN 34000041 SS Input Terminals Keyswitch A EM BEEN S EUER Keyswitch B Keyswitch C Keyswitch Zone Section Serials Input Keyswitch A 1 0501 020000A2 001 Keyswitch B 2 0502 34000041 002 Keyswitch C 3 0503 34000041 006 16 REFERENCE amp INSTALLATION MANUAL 5 2 KEYSWITCH DEFINITIONS Keyswitch Definitions determine how the control panel reacts when a keyswitch is activated 5 2 1 Keyswitch Disabled SECTIONS 0601 To 0632 FIRST DIGIT O Disables keyswitch input 5 2 2 Momentary Keyswitch SECTIONS 0601 To 0632 FIRST DIGIT 1 To arm a partition using the Momentary Keyswitch turn on the keyswitch for approximately three seconds then turn it off Repeating this sequence will disarm the system The selected Keyswitch Option see section 5 4 determines the type of arming 5 2 3 Maintained Keyswitch SECTIONS 0601 To 0632 FIRST DIGIT 2 To arm a partition using the Maintained Keyswitch turn the switch from the ON to the OFF position To disarm a partition set the keyswitch in the ON position The selected Keyswitch Option see section 5 4 determines the type of arming If the keyswitch s Arm Only option is enabled the control panel will not perform any action when the switch is in the on position 5 2 4 Generates a Utility Key Event on Open SECTIONS
143. on 8 Option Feature 8 ON 38 400 baud 8 OFF 119 200 baud default SY f communication between the control panel and the computer is experiencing difficulty at 38 400 baud especially over long distances disable option 8 and reduce the baud rate of the software to 19 200 baud 11 9 PARTITIONING SECTION 3031 OPTIONS 1 TO 8 Default only partition 1 enabled The control panel can provide up to eight completely independent partitions Most features and options can be independently set for each partition such as Event Reporting Entry Exit Delay Bell Squawk One touch Arming Panic Alarms and many more All zones keyswitch zones user codes and system modules are assigned to specific partitions making this a true partitioned system Enable the option s that correspond to the desired partition s Option Description Option Description 1 Partition 1 5 Partition 5 2 Partition 2 6 Partition 6 9 Partition 3 7 Partition 7 4 Partition 4 8 Partition 8 11 9 1 Panel Partition Assignment SECTION 3020 Default 2 00 The control panel will report system events as originating from one or all enabled partitions The System Troubles i e AC Failure TLM Failure etc can only be viewed through the partitions enabled in this section Enter a 2 digit decimal number from 01 to 08 which represent partitions 1 to 8 Enter 00 to disable this feature 11
144. on 8 is enabled and an Entry Delay zone is bypassed an armed Follow Zone see section 4 3 3 that opens without an Entry Delay being triggered will switch to the partition s Entry Delay 2 For example zone 1 is an Entry Delay and zone 2 is a Follow zone protecting the area where the keypad is installed The partition is armed but zone 1 is bypassed When option 8 is enabled zone 2 will trigger Entry Delay 2 instead of an alarm when the user approaches the keypad to disarm the partition Enable option 8 in the desired section Partition 1 3122 Partition 3 3322 Partition 5 3522 Partition 7 3722 Partition 2 3222 Partition 4 3422 Partition 6 3622 Partition 8 3822 Partition 1 3122 Partition 3 3322 Partition 5 3522 Partition 7 3722 Partition 2 3222 Partition 4 3422 Partition 6 3622 Partition 8 3822 6 10 1 No Movement Timer Default 000 If No Movement Auto Arming is enabled see section 6 10 the control panel will attempt to arm the system if no movement has occurred for the period specified by the No Movement Timer Select the section corresponding to the desired partition and program the time without movement necessary before the control panel will arm and or send the No Movement report code If No Movement Auto Arming is disabled the control panel can still send the No Movement report code For example to
145. one Section Seriali 1 0001 21000033 2 0002 1A000252 3 0003 020000A2 4 0004 34000041 Detector A 252 SN 21000033 Hardwired Device C Inputit N A N A 002 005 4 1 1 Clearing a Zone s Numbering For LCD Keypads 1 Enter a section number between 0001 to 0096 2 Press 0 and then ENTER to save and exit For Grafica Keypads 1 Enter a section number between 0001 to 0096 2 Press 0 to clear the serial number 3 Use Grafica s scroll keys highlight the input number and then press 0 to clear the data 4 Press Grafica s center action key Save to save and exit 4 2 ZoNE DouBLING ATZ SECTION 3033 OPTION 8 Default disabled The ATZ feature is a software oriented feature that enables two detection devices to be installed per hardwired input terminal section 2 15 on page 8 and see section 2 14 on page 8 Each detection device has its own zone displays its zone status on the keypad and sends its own alarm codes Fire Zones cannot be doubled Partition 3 Entry Delay 1 Timer 3311 Entry Delay 2 Timer 3312 Partition 7 Entry Delay 1 Timer 3711 Entry Delay 2 Timer 3712 Partition 4 Entry Delay 1 Timer 3411 Entry Delay 2 Timer 3412 Partition 8 Entry Delay 1 Timer 3811 Entry Delay 2 Timer 3812 Input Doubled Zone Input Input 01 Input 13 ATZ of Input 01 Input 02 Input 14 ATZ of Input 02 Input 03 Input 15 ATZ o
146. ored and controlled requires an Access Control Module DGP2 ACM1P The keypad or module is assigned to the door through the its serial number in sections 2201 to 2232 DigiplexNE supports up to 32 Doors 13 5 ACCESS LEVELS SECTIONS 2601 To 2615 Access Levels determine which Doors a user can access Each Access Level is a combination of the Doors from sections 2201 to 2232 see section 13 4 Access Levels are assigned to the users through their User Access Codes refer to the System Manager s Manual For example if the options 1 2 and 3 are enabled in the First Screen of section 2601 any User assigned to Level 01 will only have access to doors 01 02 and 03 Access Levels from 01 to 15 are programmed in sections 2601 to 2615 respectively Each section contains four screens of 8 options representing the 32 Doors Level 00 allows the user access to all the Doors For each Access Level enable or disable the options as required Section Options 1 to 8 represent 1st Screen 2nd Screen 3rd Screen 4th Screen Doors Doors Doors Doors Level 01 2601 01 to 08 09 to 16 17 to 24 25 to 32 to Level 15 2615 01 to 08 09 to 16 17 to 24 25 to 32 13 6 AccESS SCHEDULES SECTIONS 2401 To 2432 The Access Levels described in section 13 5 determine the Doors a user can have access to and the Schedules determine when the user can have access to those Doors Each Schedule consists of
147. osiProx CR R880 A reader 13 1 COMMON ACCESS CONTROL TERMS Access Alarm An audible or silent warning generated by the reader to indicate that an Access Door is open past the programmed time allowed or that it was opened without an Access Granted or Request for Exit signal This event is logged in the Event Buffer but cannot be reported Access Card A tag assigned to a User Access Code used to identify the user to the Access Control system By presenting the tag to a reader the System can verify whether the tag is valid Access Denied An Access Control term for the system s refusal to admit access through an Access Door Access Granted An Access Control term for the system permitting admission through a protected door Burglar Alarm An audible or silent warning sent to the control panel indicating that an armed zone in the DigiplexNE security system has been breached This event is logged in the Event Buffer and can be reported to a Monitoring Station Door Left Open Each Access Door is programmed with a period of time it is allowed to remain open Once the door has been open past this time limit an Access Alarm will be triggered Forced Door An Access Door was opened without an Access Granted or Request for Exit signal a silent or audible Access Alarm can be triggered Reader An Access Control device Posiprox CR R880 A normally located near an Access Door that serves to relay the information from an Access Car
148. owerS ave 0 ee o ee SEA 34 Power Supply Connections sess 7 Power Unit Consumption Table 6 Primary Schedule A AA dE 39 Problems See Trouble Display Procedure to Install viii 4 Programmable Output 4 As a 2 wire smoke detector sss 9 As a 4 wire smoke detector sss 9 Connections ce Rs 4 EE RE MTS 4 leese ul te MEET 11 Decimal Programming oi iui deest uu ut ir tale ads 11 Feature Select Method 11 Hexadecimal Programming cesse 11 Mod les EE GEGEE so ee Haa Ads EE VERNA en 11 33 Zone Programming ses he EE vk PES onore da BR aedes 12 Pulse Dialing es EER EE EE EDE RS ES DEER ee ee EE EE aia WEE ER ER OON OPE See se Eg 30 Pulse formats See Standard Pulse Formats Pulse Ratio eot OE AE ded e ine EE 30 Pulsed Audible Alarm shes soning dd it dro tonne P tcm agen 15 R ze lp EU 38 Recent Close Delay eet oce c BE ES dE EE E T ARR e 28 Record REX events ii KEES RE OR DEE Se a eh e 40 Recycle Ala rm ase sie sock pin EO ER eet Ae AE sh 21 ale ede EA RE ER OE UA ee fe 21 Regular Arming eost ONSE a RR RR AER ENT dE aod e ERE ERENS VANGS N EE 42 Report Only veces ot cers eee gre RR M ob EUR OO NEQNE EE 15 ReportSehedules tatoo a tadas 25 Reporting ae EE dE eee NENNEN NE 27 Request do RE ED OE dE e RIA MEE 38 Request for Exit REX event 40 Reset Hardware dece RR RENE ERE E tad STN R ER 32 Module EUM I 33 Software ics er eet er EG ERE Ve EN CEU dns UR SNMP HUE 32
149. panel outputs are rated to operate between 10 8Vdc and 12 1Vdc 700mA maximum Bell Output CoNTROL PANEL UL COMPLIANT SYSTEMS AC Power 16Vac 40VA 60Hz Battery 12Vdc 4Ah minimum Auxiliary Power 11 4 to 12 5Vdc 200mA maximum fuseless shutdown at 1 1A Bell Output 11 4 to 12 5Vdc shutdown 9 3A PGM Output PGM1 100mA PGM2 and PGM3 5A relay Event Buffer 2048 events All control panel outputs are rated to operate between 11 4Vdc and 12 5Vdc 1A maximum fuseless Specifications may change without prior notice UL Note The DGP NE96 control panel has been tested with the LCD Keypad DGP2 641 only General Note 1 Please note that only LCD and Grafica keypads can be used to program the DigiplexNE system LED keypads cannot be used to program the system General Note 2 Please note that the steps may differ when programming with the Grafica keypad DNE K07 If not indicated refer to the complete Grafica User Manual which can be downloaded for free from our Web site at www paradox ca DIGIPLEXNE CONTROL PANEL 3 INSTALLATION a a IaIaIaeaaaaammmmmmmmmmmmmmImImImImImImmmmmmmmTTT 2 1 RECOMMENDED INSTALLATION PROCEDURE In order to facilitate installation we recommend connecting the modules in small groups and verifying the system after every group is connected instead of verifying the system only after all modules are connected Step 1 Install the control panel Step 2 Con
150. pment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas CAUTION Users should not attempt to make such connections themselves but should contact the appropriate electrical inspection authority or electrician as appropriate The Load Number LN assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device to prevent overloading The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all of the devices does not exceed 100 Industry Canada certification is only applicable to installation of devices which include transformers approved by the Canadian Standards Association CSA O 2002 2003 Paradox Security Systems Ltd DigiplexNE WinLoad NEware Omnia and InTouch are trademarks or registered trademarks of Paradox Security Systems Ltd and its affiliates in Canada the United States and or other countries All
151. port oni 15 Inp t Speed TT 15 Instant esee de Seen dada etre ie de Aa Gee date ata 13 IritelliZorne rte tad Pose aac ebbe rt TEN velle 15 Partition Assignment xes e e e e e e e e e e K ee een 14 Pulsed Audible Alarm is sed stesse toe see RS Ee 15 Silent Alatm EE ETE A CEU e EGO ER efe da 15 Standard 24Hr Fire Zone 14 Slay Delay Zone aiibi AD 14 Stay ZONE scs ess ty dete eee te ct etg d deo d ng uv rette 15 Steady Audible Alarm 15 Zone Doubling A TZ eei ete a EE NENNEN Nee 13 Zone OPTIONS nee o ee ras 14 WARNINGS AAA AE A Re FCC Warnings IMPORTANT INFORMATION This equipment complies with Part 68 of the FCC rules subpart D and CS 03 Inside the cover of this equipment is a label that contains among other information the FCC registration number of this equipment NOTIFICATION TO TELEPHONE COMPANY Upon request customer shall notify telephone company of particular line to which the connection will be made and provide the FCC registration number and the ringer equivalence of the protective circuit FCC REGISTRATION NUMBER RINGER EQUIVALENCE NUMBER USOC JACK 5A7CAN 22633 AL E 0 1B U S 8 CANADA RJ31X USA CA31A CANADA TELEPHONE CONNECTION REQUIREMENTS Except for telephone company provided ringers all connections to the telephone network shall be made through standard plugs and telephone company provided jacks or equivalent in such a manner as to allow for easy immediate discon
152. power and the battery PLEASE NOTE It is strongly recommended that you test your System on a weekly basis and have your system checked by a qualified technician a minimum of every 3 years PLEASE NOTE When powering up the DGP NE96 control panel V1 02 or higher the panel will begin a module scan to verify if all the modules connected to the panel are operational The scanning process will take between 30 and 120 seconds to complete depending on the number of modules connected to the control panel The module scan is complete when the LCD keypad begins to show the partition status Only after the module scan is complete will the control panel be fully operational DIGIPLEXNE CONTROL PANEL 5 2 11 CALCULATING POWER REQUIREMENTS E Table 1 Power Unit Consumption Table Description QTY PU used by each Total PU Grafica Graphic LCD Keypad DNE K07 IX 48PU TI BU LCD Keypad DGP2 641 X 80PU PU LED Keypad DGP2 648 X 115PU PU Addressable Detectors DG85 DGP2 50 60 70 X 30PU PU Addressable Door Contact DGP2 ZC1 X 30PU PU 1 Zone Hardwire Expansion Module DGP2 ZX1 X 14PU PU 4 Zone Hardwire Module APR3 ZX4 X 28PU PU 8 Zone Hardwire Module APR3 ZX8 X 28PU PU Wireless Module OMN RCV3 X 50PU PU 1 PGM Output Module APR3 PGM1 X 28PU PU 4 PGM Output Module APR3 PGMA X 150PU PU Printer Module APR3 PRT1 X 40PU PU DVACS Module DGP2 DVAC X 40PU PU Annunciator Module DGP2 ANC1
153. r Left Open sse eee ie de ke ke ek ee ek eke ke ek 40 Alternate Dialing Option EEN 28 Burglar Alarm On Forced DOOF ee ee ee ee ee 40 ELE ENEE 19 Burglary ZONES eese eoe dene ENEE NEEN haan 13 AND Door Access Mode REEE EEE EEE 39 Bus Connection in Noisy Environments esses 9 Answer Vi oe ube nece nde eii data nt nt EEN H d de ede ead EE 33 RUS SS eee iactata ated sa lares A 32 Answering Machine Override Delay 41 Busy Tone Detection ee ee ee ee ee ee 30 Arming and Disarming Report Schedules sese ee ee e e se ek e RR ER ee 25 EE AR MA AE EO EE 13 Arming Follows Patton 18 Bypass Programming seen 42 Arming Report Schedule 26 Bypass Recall enn 43 EE EE SEN aU Bypass Zones iod DER EE ee e e E De Tea de 14 Arming Disarming Reporting iii ee Re RR RE teen Ke ER ee Re ek ee 25 C Arming Disarming Schedule Tolerance Window 26 Wed Call Back Feature ccce doe ee entr be rere E ed he e cuter eR 41 ASSIGNING DOOS i EE ET 38 SO S i M Call Direction isisi ini ete ve oed n e vaca tin Ute Ee Ee Ee dale 27 Assigning keyswitches to partitions see 17 LN KCN T 13 Call WinLoad reo tte et der edes id e 33 Audible Alarm O ee EE eM D NA e cg 22 AE En gp E 23 Bell Cut off Timer EEN 21 Card and OOOO ACCESS nee arden piece 39 TT A A E A AN 15 Gard can DISalm EA S Y ec 37 Cr 15 Card to Unlock and Code to Disarm sss sse ee eee ee eee ee nro 37 Auto Report Code Programming
154. r or any other person for any loss or damages whether direct or indirect or consequential or incidental including without limitation any damages for lost profits stolen goods or claims by any other party caused by defective goods or otherwise arising from the improper incorrect or otherwise faulty installation or use of the merchandise sold 60 REFERENCE amp INSTALLATION MANUAL Notwithstanding the preceding paragraph the Seller s maximum liability will be strictly limited to the purchase price of the defective product Your use of this product signifies your acceptance of this warranty BEWARE Dealers installers and or others selling the product are not authorized to modify this warranty or make additional warranties that are binding on the Seller ATTACHMENT LIMITATION NOTICE The Industry Canada label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operational and safety requirements The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equi
155. re 2 9 To comply with CONTROL PANEL TERVINALS UL955 install the 4 wire smoke detectors with 18 gauge wire If power is interrupted the relay causes the control panel to transmit the Fire Loop Trouble report programmed in section 2906 To reset unlatch connect the smoke detector s negative to a PGM Then program the PGM with the Smoke Detector Power Reset activation event see section 10 1 on page 31 Event Group 067 start 004 end 004 to interrupt power to the smoke detector for four seconds when the CLEAR and ENTER keys are pressed and held for two seconds If ATZ is enabled see see section 4 2 on page 13 do not use Note It is recommended that the smoke detectors be connected in a daisy chain configuration the extra input doubled zone For example in this example input 13 cannot be used 2 18 TELEPHONE LINE CONNECTIONS Depending on the installation the telephone lines can be connected directly to the control panel or through a CA38A or RJ31 as shown in Figure 2 10 The secondary telephone line terminals optional can be used as a backup telephone line If the Event Call Direction process fails and the control panel is unable to communicate with the Monitoring Station through the main line the control panel will switch to the second line and repeat the Event Call Direction process see section 8 8 on page 27 UL Note Installer must verify line seizure after every installation Figure 2 10
156. rence amp Installation Manual 2 Card can Disarm 3 Card with Extended Unlocked Period 4 5 OFF OFF Arming Disabled Cannot arm partitions ON OFF Regular Arm Card can Regular Arm OFF ON Stay Arm Card can Stay Arm ON ON Force Arm Card can Force Arm Add Tolerance Card and Code use the Schedule 6 Windows to Tolerance Windows see section 8 3 3 on Schedules page 26 and section 13 9 on page 39 ON Code is only valid during assigned Schedule see section 12 7 2 OFF Code is valid at all times ON A door contact must be installed on the Door the Door must be assigned to a zone section 4 1 and the zone defined as an Entry Delay A valid Card can unlock the Door but cannot disarm the partition If the partition is armed the Entry Delay is triggered and a User Access Code must be entered to disarm the area User Option 5 Arm Only and Access Control Option 2 Card can Disarm must be disabled for this feature to function OFF A valid Card can unlock the Door and disarm the partition Code follows 7 Schedule Card to Unlock and Code to Disarm 8 12 7 4 Access Card Assignment SECTIONS 1002 TO 1999 Access CARD SCREEN The Access Card is activated by assigning its serial number to the User Access Code Digiplex NE supports 26 bit Wiegand proximity cards and readers recommended Position Technology s CR R880 A reader and CR R700 Serie
157. rtaining to any keypad as Keypad 00 When Keypad Numbering is used each keypad is identified by a specific number The keypad is assigned to a Keypad Number from 1 to 32 through the keypad s serial number in sections 2801 to 2832 Enter the 8 digit serial keypad serial number in the desired section DIGIPLEXNE CONTROL PANEL 15 L KEY SWITCH PROGRAMMING The DigiplexNE control panel can support up to 32 keyswitch zones in addition to the 96 standard zones A keyswitch allows a user to arm or disarm a System by pressing a key or by toggling a keyswitch A keyswitch can also be used to generate a Utility Key event which can then be used to activate or deactivate PGM outputs connected to the DigiplexNE system The keyswitches are connected to the hardwired input terminals of either the control panel zone expansion modules or the keypad For installation instructions see section 2 9 on page 4 Keyswitches must be programmed as described in this section see Figure 5 1 UL Note Keyswitches are not to be used in UL Listed systems Figure 5 1 Keyswitch Programming Press amp hold the 0 key v Enter your INSTALLER CODE v Enter 4 digit SECTION Keyswitch Numbering Keyswitch L Sections 0501 to 0532 represent keyswitches 1 to 32 respectively Enter the module s 8 digit SERIAL NUMBER where the keyswitch is installed Enter the 3 digit INPUT NUMBER where the keyswitch
158. rtition 5 Option 5 Partition 5 Option 6 Partition 6 Option 6 Partition 6 Option 7 Partition 7 Option 7 N A Option 8 Partition 8 Option 8 Partition 8 Partition 4 3421 Partition 4 arms disarms with Partition 8 3821 Partition 8 arms amp disarms with Option 1 Partition 1 Option 1 Partition 1 Option 2 Partition 2 Option 2 Partition 2 Option 3 Partition 3 Option 3 Partition 3 Option 4 N A Option 4 Partition 4 Option 5 Partition 5 Option 5 Partition 5 Option 6 Partition 6 Option 6 Partition 6 Option 7 Partition 7 Option 7 Partition 7 Option 8 Partition 8 Option 8 N A 6 2 RESTRICT ARMING ON SUPERVISION Loss SECTION 3034 OPTION 4 Default disabled When option 4 is enabled the control panel can restrict arming if it receives a supervision loss signal from the Omnia 433MHz Wireless System OMN RCV3 see section 7 3 Partitions will not arm until all supervision loss trouble conditions are corrected 6 3 RESTRICT ARMING ON TAMPER SECTION 3034 OPTION 8 Default disabled When option 8 is enabled the control panel prevents arming if it detects a tamper on a zone or module see section 7 5 Partitions will not arm until the Installer Code is entered and tamper trouble conditions are corrected 18 REFERENCE amp INSTALLATION MANUAL 6 4 RESTRICT ARMING ON AC FAILURE SECTION 3035 OPTION 1 Def
159. s DI AC Failure running on the backup battery The backup battery is disconnected needs 2 Battery Trouble to be recharged or replaced Devices connected to AUX have exceeded current limits 1 1A The Auxiliary Output will shutdown until the trouble is corrected 3 AUX Current Limit The bell or siren has exceeded current limits 3A The Bell Siren Output will shutdown until the trouble is corrected 4 Bell Current Limit The bell or siren is not connected When the bell output is not used connect a 1kQ resistor across the bell output 5 Bell Absent The control panel registers a data memory 6 ROM Check Error error Contact distributor for replacement The control panel registers a work memory 7 RAM Check Error error Contact distributor for replacement GROUP 2 COMMUNICATOR The control panel is unable to access the EU TLM main telephone line 2 Fail to Communicate 1 3 Fail to Communicate 2 4 Fail to Communicate 3 5 Fail to Communicate 4 The control panel tried all assigned telephone numbers and failed to contact the Monitoring Company The control panel is unable to 6 Fail to Communicate PC communicate with the WinLoad software GROUP 3 MODULES 1 Module Tamper A module s tamper switch was triggered A module is experiencing a data memory le ROM Check Error error Contact distributor for replacement A module is unabl
160. s From programming mode see section 3 4 enter any of the following sections to set the indicated report codes with the default values FF from the Automatic Report Codes List in the Programming Guide Section Description 4030 Resets all the report code sections to 00 cleared 4031 Sets all the report code sections to FF defaults Section Sets to Defaults FF Reset Sections Zone Alarm and Restore Report Codes Ko Tamper and Restore Report Codes 0201 to 0296 Keyswitch Arming Report Codes 0701 to 0732 4033 Keyswitch Disarming Report Codes 0801 to 0832 Access Code Arming Report Codes Access Code Disarming Report Codes 2001 to 2099 2101 to 2199 4034 Special System Report Codes 3900 to 3909 4035 Special Arming Report Codes Special Disarming Report Codes 3910 to 3919 3920 to 3929 4036 Special Alarm Report Codes 3930 to 3939 4037 Trouble and Restore Report Codes 3940 to 3991 8 16 CLOSING DELINQUENCY TIMER Default 2 000 Disabled When a partition in the system is disarmed the control panel will start the corresponding partition s Closing Delinquency Timer which is programmed for each partition If the Closing Delinquency Timer elapses before the partition is armed again DigiplexNE will transmit a Closing Delinquency report code to the central monitoring station Enter a value from 001
161. s cards Enter the serial number manually or present the Access Card to the keypad s reader and its serial number will register automatically DIGIPLEXNE CONTROL PANEL 37 ACCESS CONTROL SYSTEM FEATURES Access Control defines the days and times people are allowed to enter and exit a site An Access Control door uses a reader an Access Control Module a Request for Exit motion detector a door contact and an electronic door strike to unlock the door for authorized personnel at authorized times For details on connecting these devices refer to the Digiplex DigiplexNE Access Control Module Reference amp Installation Manual Figure 13 1 Typical Access Control Installation 6 1 Request for Exit Device Paradoor 2 Door Contact 3 Reader PosiProx or PosiPIN on other side of the wall 4 Access Control Module DGP2 ACM1P 5 Locking Device 6 Control Panel DGP NE96 Each person authorized to access the protected area is issued a card The card is assigned to a User Access Code programmed with an Access Level see section 13 5 and a Schedule see section 13 6 When a card is presented to the reader the control panel determines whether or not to unlock the door depending on if the card is allowed to open that door and if the card is permitted at that particular time and day UL Note For UL Listed systems the DGP2 641AC keypad shall be used for Access Control systems The keypad is only compatible with the P
162. s to leave the protected area before the control panel arms the partition The Exit Delay applies to all zones in the partition except 24Hr Zones Program the Exit Delay from 001 to 255 seconds Partition 1 3108 Partition 3 3308 Partition 5 3508 Partition 7 3708 Partition 2 3208 Partition 4 3408 Partition 6 3608 Partition 8 3808 6 16 1 Exit Delay Termination Default enabled The control panel can reduce the Exit Delay to 7 seconds when an Entry Delay zone see section 4 3 2 is opened and closed during the Exit Delay For example 15 sec into a 45 sec Exit Delay an Entry Delay zone opens and closes The remaining 30 sec is reduced to 7 sec DIGIPLEXNE CONTROL PANEL 19 Figure 6 1 Example of Exit Delay Termination Entry Delay Exit Delay reduced zone closed to 7 seconds 0 15 22 45 45 second Exit Delay Enable option 4 in the desired section Partition 1 3122 Partition 3 3322 Partition 5 3522 Partition 7 3722 Partition 2 3222 Partition 4 3422 Partition 6 3622 Partition 8 3822 Emits 1 squawk upon arming and 2 squawks upon disarming with a remote control using the Omnia Wireless System OMN RCV3 default 2 enabled Remote Arming Disarming 6 6 19 RING BACK After disarming the system the control panel can warn the user that there was an alarm and that it may be dangerous to ent
163. se to an AC source ground connection and telephone line connection 2 3 EARTH GROUND Connect the zone and dialer ground terminals from the control panel to the enclosure and cold water pipe or grounding rod as per local electrical codes For maximum lightning protection use separate earth grounds for the zone and dialer grounds see Figure 2 3 on page 5 2 4 AC POWER Use a 16 5Vac 50 60Hz transformer with a minimum 20VA rating to provide sufficient AC power For increased power use a transformer with a 40VA rating For UL Listed systems use model BE156240CAA For CSA listed systems use model BE116240AAA Do not use any switch controlled outlets to power the transformer Connect the transformer as shown in Figure 2 3 on page 5 Do not connect the transformer or the backup battery until all wiring is completed PLEASE NOTE When powering up the DGP NE96 control panel V1 02 or higher the panel will begin a module scan to verify if all the modules connected to the control panel are operational The scanning process will take between 30 and 120 seconds to complete depending on the number of modules connected to the control panel The module scan is complete when the keypad begins to show the partition status Only after the module scan is complete will the control panel be fully operational 2 5 BACKUP BATTERY To provide power during power loss connect a 12Vdc 4Ah rechargeable acid lead or gel cell backup battery YUA
164. stem by adding plug and play expansion modules anywhere and in any combination on the 4 wire combus Modules are connected to the combus at the most convenient location and then their zone inputs are assigned to the desired zone and partition Also only a module s used inputs are assigned to zones in the system Keyswitches remote controls and unused module inputs do not use up zones Once installed all combus modules including motion detectors can be programmed remotely via a keypad or the WinLoad upload download software DigiplexNE also supports 32 virtual zones in addition to its 96 security zones and 32 access control doors Virtual zones can be used to automate PGM activations without occupying a security zone and without affecting the system s security functions DigiplexNE is a logical solution to every installer s security access control and home automation installation needs CTR 21 APPROVAL The DigiplexNE control panel DGP NE96 meets the European Union Common Technical Requirement CTR 21 The CTR 21 requirement is an electrical standard that defines the analogue interface for all two wire telecommunications equipment i e DECT PABXs etc intended for connection to the Public Switched Telephone Network This allows the DigiplexNE control panel to be used in as many as 19 countries such as Belgium Germany Greece Portugal Sweden and Switzerland DigiplexNE control panels with the CTR 21 approval are available as an option on
165. t the speed to Normal or install a Hub APR3 HUB2 on the combus The modules will detect the speed set in the control panel and adjust their internal parameters accordingly When a change is made to the combus speed the control panel will restart within one minute to allow the modules to adjust to the change Option Feature 8 ON High Speed 8 OFF Normal Speed default will occur and is considered normal operation The message COMM TROUBLE CALL SERVICE will be displayed on keypads connected to the combus The AC and STATUS LEDs will begin to alternately flash and all operations on the system will be suspended for approximately one minute while the system reconfigures itself g Please note that when the combus speed is changed the following 11 7 TRANSMIT ZONE STATUS ON SERIAL PORT SECTION 3035 OPTION 7 By enabling option 7 the control panel will transmit zone status information zone open zone close zone tamper and fire loop through the serial port Use this feature when there are devices or software connected to the serial port of the control panel that require zone status information such as WinLoad and the APR3 PRT1 Printer Module 11 8 SERIAL PORT BAUD RATE SECTION 3035 OPTION 8 When option 8 is enabled the serial port s baud rate is 38 400 baud When option 8 is disabled the baud rate is 19 200 baud Depending on the baud rate set in WinLoad or NEware enable or disable opti
166. t to your telephone line and still have all of those devices ring when your telephone number is called In most but not all areas sum of the REN s of all devices connected to one line should not exceed five 5 To be certain of the number of devices that you may connect to your line you may want to contact your local telephone company EQUIPMENT MAINTENANCE FACILITY If you experience trouble with this telephone equipment please contact facility indicated below for information on obtaining service or repairs The telephone company may ask that you disconnect this equipment from network until problem is corrected or until you are sure that the equipment is not malfunctioning FCC PART 15 WARNINGS INFORMATION TO USER This equipment has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 of FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to equipment intermittently the user is encouraged to try to correct the interference by one or more of the following measures 1 reorient or relocate th
167. tc A zone programmed as Fire becomes normally open will not function as normally closed and requires an EOL resistor The keypads must be assigned to the same partition as the Delayed 24Hr Fire zone for the buzzer to activate Figure 4 3 Delayed 24Hr Fire Zone Delayed Fire Zone Triggered Activate bell siren output amp delay report transmission for 30 seconds Has the zone closed within 30 seconds Latch alarm and transmit report code as described in the section Standard 24Hr Fire Zone Has a 2nd Delayed Fire Zone opened in 30 sec Any key on keypad pressed within 30 seconds Bell siren silenced Delay report transmission an additional 90 sec Problem corrected END Alarm Disabled 14 REFERENCE amp INSTALLATION MANUAL 4 3 13 Standard 24Hr Fire Zone SECTIONS 0101 To 0196 FIRST DIGIT D A zone programmed as Fire becomes normally open will not function as normally closed and requires an EOL resistor When a Standard 24Hr Fire Zone triggers the control panel can send a Zone Alarm report code see section 8 2 1 on page 24 send a Fire Loop Trouble Report see section 8 2 11 on page 25 if a tamper wiring fault occurs on a Fire Zone A Zone Fault Trouble will also appear in the keypad s Trouble Display generate a Fire alarm which is always audible regardless of other settings Fire alarms generate an intermittent signal see Figure 4 4 Fig
168. tedly during the same alarm which may cause several reportings and further activation of the bell output When option 1 is enabled the control panel will stop regenerating alarms on the zone during the same armed period once the Auto Zone Shutdown Limit is reached The Auto Zone Shutdown Limit resets every time the system is armed To program the Auto Zone Shutdown Limit key in the desired 3 digit counter 000 to 255 into section corresponding to the desired partition 000 disabled Partition 1 3114 Partition 5 3514 Partition 2 3214 Partition 6 3614 Partition 3 3314 Partition 7 3714 Partition 4 3414 Partition 8 3814 4 5 2 Bypass Zones SECTIONS 0101 To 0196 OPTION 2 Only zones with option 2 enabled can be Manually Bypassed see section 15 7 Fire Zones cannot be bypassed Default enabled 4 5 3 Stay Zones SECTIONS 0101 To 0196 OPTION 3 Only zones with option 3 enabled will be bypassed when the partition is Stay Armed see section 15 2 or Instant Armed see section 15 3 All other zones will remain activated Fire Zones cannot be set as Stay Zones 4 5 4 Force Zones Not to be used with UL Listed systems SECTIONS 0101 To 0196 OPTION 4 Only zones with option 4 enabled can be bypassed when the partition is Force armed see section 15 4 Fire Zones cannot be Force Zones 4 5 5 Alarm Types SECTIONS 0101 To 0196 OPTIONS 5 amp 6 Opt
169. ter their ACCESS CODE 2 Press the 9 key 3 Press the 2 key 4 Enter the time that keypads will start beeping when Chime Zones are opened according to the 24 hour clock i e 9PM is 21 00 5 Enterthe time that keypads will stop beeping when Chime Zones are opened according to the 24 hour clock i e 9PM is 21 00 6 Press ENTER key to save 15 9 KEvPAD SETTINGS The keypad s settings can be modified to suit the user s needs The instructions that follow are for LCD and LED keypads only for Grafica keypads refer to the Grafica Online Manual which can be downloaded for free from our Web site at www paradox ca For LCD Keypads Scrolling Speed is how long the messages stay on the LCD screen before moving to the next message Backlight is the illumination behind the keys and the screen Contrast is how dark the characters appear on the LCD screen To change the settings 1 Enter the USER ACCESS CODE 2 Press 6 3 Press 1 Scrolling Speed from 0 to 10 10 slowest Press 2 Backlight from 0 to 7 7 brightest Press 3 Contrast from 0 to 4 4 most contrast 4 Usethe A and V keys to increase or decrease the numbers 5 Press ENTER 6 Press CLEAR to exit or the W key to move to the next setting For LED Keypads Modify Backlight only 1 Enter an ACCESS CODE 2 Press the 6 key 3 Use the A and V keys to increase or decrease the illumination The range is between zero an
170. the Access Card i e through its assigned Access Level and Schedule Doors 01 to 32 are programmed in sections 2251 to 2282 respectively For each door enable or disable the option as required Option Feature 2 ON 2 OFF Access with Card only ACC key enabled S This option is not available for LED and Grafica Keypads 13 12 CARD AND CODE ACCESS SECTION 2251 TO 2282 OPTION 3 For higher security areas the Access Door can be programmed to require a user to present a valid Access Card and then enter the same user s valid code before access is granted The Access Card must be presented to and the user code must be entered on a PosiPINTM Proximity Card Reader and Keypad CR R885 BL that is connected to an Access Control Module DGP2 ACM1P PosiPIN and the Access Control Module must be configured to allow access of this type Please refer to the PosiPIN Installation and Operating Instructions and to the Access Control Module Reference amp Installation Manual for programming instructions Doors 01 to 32 are programmed in sections 2251 to 2282 respectively For each door enable or disable the option as required DIGIPLEXNE CONTROL PANEL 39 Option Feature 3 ON Access Card AND User Access Code required 3 OFF Access Card OR User Access Code Kw When option 3 is enabled the Access Card must be presented before the User Access Code is entered 13 13 SKIP EXIT
171. the delay 1 An alarm occurs on another zone 2 The zone in alarm restores and reoccurs Key in the desired 3 digit delay value 001 to 255 minutes 000 disabled into the section corresponding to the desired partition 7 2 3 Recycle Delay Default 000 The Recycle Delay is the amount of time the control panel will wait after the Bell Cut off occurs before re verifying the zone status Program the Recycle Delay from 001 to 255 minutes 000 disabled Partition 2 3217 Partition 4 3417 Partition 6 3617 Partition 8 3817 Partition 1 3118 Partition 3 3318 Partition 5 3518 Partition 7 3718 Partition 2 3218 Partition 4 3418 Partition 6 3618 Partition 8 3818 Partition 1 3116 Partition 3 3316 Partition 5 3516 Partition 7 3716 Partition 2 3216 Partition 4 3416 Partition 6 3616 Partition 8 3816 7 5 TAMPER RECOGNITION OPTIONS SECTION 3034 OPTIONS 5 AND 6 When the control panel detects a tamper or wire fault on a zone or on an expansion module the control panel can generate an alarm and or trouble as shown in the table below unless the Tamper Recognition Option is disabled 7 8 WIRELESS TRANSMITTER SUPERVISION OPTIONS SECTION 3034 OPTIONS 1 AND 2 When the control panel detects a Supervision Loss wireless receiver no longer receiving signals from a wireless transmi
172. the desired partition or press 0 to disarm all their assigned partitions For Grafica Keypads 1 Enter through a designated entry The Entry Delay Timer will begin 2 Enter their ACCESS CODE 3 Using the scroll keys highlight Disarm and then press the center action key Ok If you have access to more than one area proceed to step 4 4 Highlight either Disarm All Areas or Select Area s and then press the center action key Ok If you selected the Select Area s method follow steps 5 and 6 5 Highlight the area you wish to disarm and then press the left action key Select Repeat this step for any additional area 6 Press the center action key Disarm 15 7 BYPASS PROGRAMMING Bypass Programming allows users to program the security system to ignore specified zones the next time the partition is armed To bypass a zone the zone must have the Bypass option enabled the User Access Code must have the Bypass option enabled and the zone must be within the User Access Code s partition assignment To Bypass users For LCD Keypads 1 Enter their ACCESS CODE 2 Press the BYP key 3 Enter the zone s 2 digit number or use the A and W keys and press the BYP key when the zone appears on screen 4 Press ENTER key to exit For Grafica Keypads 1 Enter their ACCESS CODE 2 Using the scroll keys highlight Bypass and then press the center action key Ok 3 Highlight the zone that you wish to bypass
173. the status of the partitions assigned to their User Access Codes Select one or more of the partitions for each User Access Code as shown in Figure 12 1 on page 36 Seng f no partition assignment is selected the User Access Code will only be able to activate PGMs 12 7 AccESS CONTROL SECTIONS 1002 To 1999 In addition to the User Access Code options the following options can be programmed when Access Control is enabled Access Level Schedule Access Options and Access Card For details on Access Control see section 13 on page 38 RE The System Master Code and User Access Codes with the Full Master feature enabled can also program the Access Level Schedule Access User Options and Access Card using another method for programming The System Master Code has access to all doors all the time A Only the card s serial number and the choice of arming method can be changed If the other options are changed the System Master Code will revert to its original programming 12 7 1 Access Level Assignment SECTIONS 1002 To 1999 LEVEL SCHEDULE SCREEN User Access Codes can only open the doors included in their assigned Access Level see section 13 5 on page 38 In the first set of brackets enter the two digit Access Level number 00 to 15 00 unrestricted to be assigned to that User Access Code 12 7 2 Schedule Assignment SECTIONS 1002 To 1999 LEVEL SCHEDULE SCREEN Schedules determine the hours days and holidays t
174. the system 12Vdc 7Ah Rechargeable Acid Lead or Gel Cell Backup Battery N ranstormer Requirements 16 5VAC 20VA Auxiliary Supply can provide typical 6 00mA max 700mA Usable Battery Charge 350mA Currents output will shutdown if the current exceeds 3A A 1KO resistor is required if the Bell is not equipped with an internal resistor The resistor must be connected between the Bell s negative and positive wires Position the resistor as close as possible to the Bell A resistor is not required for sirens resistor Bell Siren ep kop EE p sez zee For the hardwired connections see Single Zone Input Connections on page 8 and Double Zone Connections Combus on page 8 AUX Power Auxiliary Refer to the transformer requirements for the Auxiliary Power Output Also refer to the Power Unit Consumption Table To connect additional wiring to auxiliary power use the red and black keypad connectors Auxiliary power will shut down if the current exceeds 1 1A DETECTOR REO BLK GRN YEL RED BLK GRN YEL When installing the combus wires in a noisy environment or when connecting the combus across separate buildings you must use a shielded cable Refer to section 2 16 1 on page 9 Please see UL and ULC Warnings on page 59 for applicable UL ULC warnings and information PARADOX SECURITY SYSTEMS 1C 2 3 C4
175. tion 6 3606 Partition 8 3806 Partition 1 3124 Partition 3 3324 Partition 5 3524 Partition 7 3724 Partition 2 3224 Partition 4 3424 Partition 6 3624 Partition 8 3824 Option Bell Squawk on Description Emits 2 squawks upon disarming M Disarming default disabled Emits 1 squawk upon arming 2 Arming default disabled Emits 1 squawk every second for 60 seconds before Auto Arming a partition Emits a series of 3 squawks every second for 10 seconds before arming default disabled DI Auto Arming Emits 1 squawk every second during the Exit Delay Emits a series of 3 squawks every second during the final 10 seconds of the Exit Delay default disabled 4 Exit Delay Emits 1 squawk every second during the 5 Entry Delay Entry Delay default disabled 20 REFERENCE amp INSTALLATION MANUAL 6 21 DISPLAY BYPASS IF ARMED SECTION 3033 OPTION 5 Default enabled When option 5 is enabled the keypads will not display that zones have been bypassed while the system is armed ALARM OPTIONS E 7 1 BELL ALARM OUTPUT Default only option 1 enabled When an alarm condition is detected in a partition the control panel can toggle the on board BELL output enabling any bells or sirens connected to it In section 3032 enable the option to enable the bell output in the desired partitio
176. tivity CG Close Area CL Closing Report OP Opening Report OP Opening Report OS Opening Keyswitch OP Opening Report OP Opening Report OS Opening Keyswitch OR Disarm From Alarm OR Disarm From Alarm OS Opening Keyswitch CE Closing Extend OQ Remote Disarming OR Disarm From Alarm OP Opening Report UB Untyped Zone Bypass BA Burglary Alarm FA Fire Alarm BH Burglary Alarm Restore FH Fire Alarm Restore GA Gas Alarm KA Heat Alarm WA Water Alarm ZA Freeze Alarm GR Gas Alarm Restore KR Heat Alarm Restore WR Water Alarm Restore ZR Freeze Alarm Restore BM Burglary Alarm PA Panic Alarm MA Medical Alarm FA Fire Alarm CR Recent Closing CG Close Area HA Hold up Alarm UB Untyped Zone Bypass TA Tamper Alarm TR Tamper Restoral JA User Code Tamper AT AC Trouble YT System Battery Trouble YP Power Supply Trouble YA Bell Fault YA Bell Fault JT Time Changed FT Fire Trouble LR Phone Line restoral 52 REFERENCE amp INSTALLATION MANUAL System Event AC Failure restore Battery Failure restore Auxiliary supply trouble restore Bell output current limit restore Bell absent restore Clock programmed Fire loop trouble restore Combus fault Module tamper Module ROM RAM error Module TLM trouble Module fail to communicate to central station Printer fault Module AC Failure Module battery failure Module
177. to 096 Zone is in Fire Loop Trouble 001 to 096 001 to 096 TLM Trouble See NOTE 3 on page 50 000 000 Smoke detector reset 001 001 Arm with no entry delay 002 002 Arm in Stay mode 003 003 Arm in Away mode 004 004 Full arm when in Stay mode 005 005 Voice module access 006 006 Remote control access 007 007 Non reportable Event PC Fail to communicate 008 008 Midnight 009 009 NEware User Login 010 010 NEware User Logout 011 011 User Initiated Call up 012 012 Force Answer 013 013 Force Hang up 014 014 Any Non reportable Event Not Used Not Used User Codes 000 to 255 000 to 255 000 to 255 User Codes 256 to 511 000 to 255 000 to 255 User Code entered on Keypad User Codes 512 to 767 000 to 255 000 to 255 User Codes 768 to 999 000 to 231 000 to 231 Any User Code Not Used Not Used Door Numbers 001 to 032 001 to 032 User Card Access on Door Any door Not Used Not Used 000 One touch Bypass Programming 000 000 000 User Codes 001 to 255 001 to 255 001 to 255 001 User Codes 256 to 511 000 to 255 000 to 255 007 Bypass Programming Access 002 User Codes 512 to 767 000 to 255 000 to 255 003 User Codes 768 to 999 000 to 231 000 to 231 255 Any User Code Not Used Not Used 000 Zone Numbers 001 to 096 001 to 096 008 TX Delay Zone Alarm 255 Any zone Not Used Not Used 000 User Codes 001 to 255 001 to 255 001 to 255 001 User Codes 256 to 511 000 to 255 000 to 255 009 Arming with Master 002 User Codes 512 to 767 000 to 255 000 to 255 003 User Codes 768 to 999 000
178. to the desired partition s or press 0 to arm all their assigned partitions For Grafica Keypads To arm users 1 Enter their ACCESS CODE 42 REFERENCE amp INSTALLATION MANUAL 2 Using the scroll keys highlight the desired arming method see Table 13 on page 42 and then press the center action key Ok If the users have access to more than one partition proceed to step 3 3 Highlight either Arm AII Areas or Select Area s and then press the center action key Ok If the user s selected the Select Area s method follow steps 4 and 5 4 Highlight a partition you wish to arm and then press the left action key Select Repeat this step for any additional partition 5 Press the center action key Arm Table 13 Arming Methods Arming Method LCD Grafica Regular ARM n EE Sta STAY Y Stay Arm Instant 5 ni Instant Arm Force FORCE n Force rm 15 6 DISARMING All users can disarm except users with Arm Only see section 12 5 enabled on their User Access Codes Users can only disarm the partitions assigned to their User Access Codes The Stay or Instant Armed partitions can also be Disarmed by using a One touch Feature To disarm users For LCD Keypads 1 Enter through a designated entry The Entry Delay Timer will begin 2 Enter their ACCESS CODE 3 Press the DISARM key If the users have access to more than one partition they can press the key corresponding to
179. tomatically arm whenever partitions 2 and 3 are armed Partition 1 will disarm when either partition 2 or partition 3 is disarmed Partition 1 3121 Partition 5 3521 Partition 1 arms amp disarms with Partition 5 arms amp disarms with Option 1 N A Option 1 Partition 1 Option 2 Partition 2 Option 2 Partition 2 Option 3 Partition 3 Option 3 Partition 3 Option 4 Partition 4 Option 4 Partition 4 Option 5 Partition 5 Option 5 N A Option 6 Partition 6 Option 6 Partition 6 Option 7 Partition 7 Option 7 Partition 7 Option 8 Partition 8 Option 8 Partition 8 Partition 2 3221 Partition 2 arms disarms with Partition 6 3621 Partition 6 arms amp disarms with Option 1 Partition 1 Option 1 Partition 1 Option 2 N A Option 2 Partition 2 Option 3 Partition 3 Option 3 Partition 3 Option 4 Partition 4 Option 4 Partition 4 Option 5 Partition 5 Option 5 Partition 5 Option 6 Partition 6 Option 6 N A Option 7 Partition 7 Option 7 Partition 7 Option 8 Partition 8 Option 8 Partition 8 Partition 3 3321 Partition 3 arms amp disarms with Partition 7 3721 Partition 7 arms disarms with Option 1 Partition 1 Option 1 Partition 1 Option 2 Partition 2 Option 2 Partition 2 Option 3 N A Option 3 Partition 3 Option 4 Partition 4 Option 4 Partition 4 Option 5 Pa
180. tter the control panel can generate an alarm and or trouble as shown in the table below unless the Wireless Transmitter Supervision Option is disabled eng The Supervision feature must be enabled in the Omnia Wireless System OMN RCV3 for this feature to function Option 1 2 Description Disabled Default Displays zone open on the keypads but will not generate an alarm or trouble Not permitted on UL systems OFF OFF Generates Trouble Only when armed or disarmed OFF ON The control panel displays Zone Fault in the Trouble Display and transmits the defined report code see section 8 2 Option 9 6 Description Disabled Default Displays zone open on the keypads but will not generate an alarm or trouble Not permitted on UL systems Generates Trouble Only when armed or disarmed OFF ON The control panel displays Zone Fault in the Trouble Display and transmits the defined report code see section 8 2 When disarmed Generates Trouble Only The control panel displays Zone Faultin the Trouble Display and transmits the defined report code see section 8 2 When armed Follows Zone Alarm Type The control panel follows the zone s alarm type see section 4 5 5 on page 15 When disarmed Generates Audible Alarm The control panel displays Zone Fault in the Trouble Display transmits the defined report code see section 8 2 and ON ON generates an audible
181. uble can only be used with DigiplexNE control panel models that have one dialer NOTE 4 This event cannot be used for a module s PGM programming If a Keyswitch Input is used the input must be defined as Generates a Utility Key Event on Open or Generates a Utility Key Event on Open and Close If a remote control is used the remote control button must be defined as a Utility Key button 50 REFERENCE amp INSTALLATION MANUAL Utility Key Event Table 14 Actions that Generate a Utility Key Event Keypad Utility Keys 1 amp 2 Keyswitch Inputs definition 3 KS Input 1 opens Keyswitch Inputs definition 4 KS Input 1 opens Remote Control Utility Key 1 RC button Utility Key Event 1 Utility Key Event 2 Utility Key Event 3 4 amp 5 7 amp 8 KS Input 2 opens KS Input 3 opens KS Input 1 closes KS Input 2 opens Utility Key 2 RC button Utility Key 3 RC button Utility Key Event 4 CLEAR amp 0 or amp 0 KS Input 4 opens KS Input 2 closes Utility Key 4 RC button Utility Key Event 5 2 amp 3 KS Input 5 opens KS Input 3 opens Utility Key 5 RC button Utility Key Event 6 5 amp 6 KS Input 6 opens KS Input 3 closes Utility Key Event 7 8 amp 9 KS Input 7 opens KS Input 4 opens Utility Key Event 8 0 amp ENTER or 0 KS Input 8 opens KS Input
182. ult disabled When option 7 is disabled the control panel sends the Disarming Report Codes see section 8 2 every time the partition is disarmed When option 7 is enabled the control panel sends the Disarming Report Codes to the Monitoring Station only when the partition is disarmed following an alarm Select the section that corresponds to the desired partition and enable or disable option 7 Partition 1 3123 Partition 3 3323 Partition 5 3523 Partition 7 3723 Partition 2 3223 Partition 4 3423 Partition 6 3623 Partition 8 3823 8 14 ZoNE RESTORE REPORT OPTIONS SECTION 3037 OPTION 8 Default disabled When option 8 is disabled the control panel sends the Zone Alarm Restore report codes to the Monitoring Station when the Bell Cut Off Timer elapses see section 7 2 or when the alarm is disarmed When option 8 is enabled the control panel sends the Zone Alarm Restore report codes see section 8 2 to the Monitoring Station as soon as the zone returns to normal zone closure or upon disarming 8 15 AuTO REPORT CODE PROGRAMMING When using either the Contact ID or SIA Reporting Formats see section 8 7 the control panel can automatically program a set of default report codes However the Contact ID Reporting Format can be modified using the manual programming method see section 8 7 4 amp section 8 7 5 to program remaining report codes or to change some of the default
183. umber from the PGM Programming Table Event Group Feature Group Start End PGM 1 0914 0915 0916 0917 PGM 2 0924 0925 0926 0927 PGM 3 0934 0935 0936 0937 10 5 PGM TIMER When the PGM Deactivation Option see section 10 2 is enabled the PGM Timer determines how many seconds or minutes see section 10 5 1 the PGM remains activated before it returns to its original state Enter the section that corresponds to the desired PGM and enter a value from 001 to 255 default 005 The value entered is either in seconds or minutes as determined by the PGM Time Base Selection see section 10 5 1 PGM 1 0918 PGM 2 0928 PGM 3 0938 10 5 1 PGM Time Base Selection The PGM Time Base Selection determines whether the PGM Timers in sections 0918 0928 and 0938 are in minutes or seconds default seconds Enter the section corresponding to the desired PGM and enable or disable option 2 PGM 1 0919 Option Feature PGM 2 0929 2 ON Minutes PGM 3 0939 2 OFF Seconds 10 6 PGM1 BECOMES A 2 WIRE SMOKE DETECTOR INPUT SECTION 3030 OPTION 1 Default disabled Enabling option 1 in section 3030 sets PGM1 to act as a zone input for two wire smoke detectors When programming Zone Numbering see section 4 1 the control panel will recognize PGM1 as input number 255 For two wire smoke detector connections please refer t
184. umber after every failed attempt to contact a Monitoring Station Telephone Number Otherwise option 6 off the control panel only dials the backup telephone number after the Maximum Dialing Attempts see section 8 8 1 to one Monitoring Station Telephone Number fail 8 9 PAGER DELAY SECTION 3057 Default 060 When using the Pager Reporting Format see section 8 7 6 the control panel will wait for the delay period programmed into section 3057 before uploading the report codes to the pager This is to allow time for the pager system to provide a dial tone or to bypass the welcome message before sending the data Enter any value between 001 and 127 to determine Pager Delay in seconds 8 10 RECENT CLOSE DELAY Default 000 If after arming the partition an alarm is generated within the programmed period the control panel will transmit the Recent Close report code programmed into section 3933 Enter any value between 001 and 255 to determine Recent Close Delay in seconds Partition 1 3109 Partition 3 3309 Partition 5 3509 Partition 7 3709 Partition 2 3209 Partition 4 3409 Partition 6 3609 Partition 8 3809 8 11 PowER FAILURE REPORT DELAY SECTION 3058 Default 030 The control panel will delay the transmission of the AC Failure report code programmed into section 3941 by the period programmed into section 3058 Enter any value between 001 and 255 to determine Po
185. ure 4 4 Bell Siren Output During Fire Alarm Bell Fire Alarm Output Latched I i On off 0 5 0 5 1 5 sec sec sec 4 3 14 Stay Delay Zone SECTIONS 0101 TO 0196 FIRST DIGIT E AND F When a Stay Delay zone is armed using the Regular or Force arming methods the control panel processes the zone as an Instant zone see section 4 3 4 When a Stay Delay zone is armed using the Stay or Instant arming methods and the zone is triggered the control panel will not generate an alarm until the programmed Stay Delay elapses A zone defined as Stay Delay 1 follows the Entry Delay 1 Timer of its assigned partition Likewise a zone defined as Stay Delay 2 follows the Entry Delay 2 Timer of its assigned partition To program the Entry Delay Timers refer to Entry Delays 1 and 2 on page 13 For example if zone 1 in Partition 5 is defined as Stay Delay 1 the timer will follow the amount programmed in 3511 4 4 ZONE PARTITION ASSIGNMENT SECTIONS 0101 To 0196 SECOND DIGIT 1 TO 8 A control panel can be divided into eight completely independent systems see section 11 9 on page 32 Assign each zone to one partition see Figure 4 1 on page 12 4 5 ZONE OPTIONS The zone options from Figure 4 1 on page 12 are described below 4 5 1 Auto Zone Shutdown SECTIONS 0101 To 0196 OPTION 1 Default 000 When option 1 is disabled the control panel generates an alarm when an armed zone is breached even if the same zone opens repea
186. wer Failure Report Delay in minutes 8 12 AuTO TEST REPORT SECTION 3037 OPTION 3 AND 4 AND SECTIONS 3040 3041 3042 AND 3043 The control panel can transmit the test report code programmed into section 3902 every hour Hourly Test Transmission or after a period of time Auto Test Report Period 28 REFERENCE amp INSTALLATION MANUAL Option Feature Description 3 4 After the number of days 000 to 255 default lt Auto Test a Report 000 programmed into section 3040 elapse the OFF OFF Period control panel can transmit the report code at the default time 00 00 to 23 59 default 00 00 programmed into section 3041 The control panel transmits the test report code at ON OFF Hourly Test the same time every hour Program the minute of Transmission each hour 00 00 to 00 59 default 00 00 when the test report should be sent into section 3041 When armed The control panel transmits the test report code at regular intervals while the partition is armed Program the number of minutes 000 to Timed Test 255 default 005 between each transmission in Transmission section 3042 when Armed When disarmed The control panel transmits the Disarmed test report code at regular intervals while the partition is disarmed Program the number of minutes 000 to 255 default 060 between each transmission in section 3043 ON ON 8 13 DISARM REPORTING OPTIONS Defa
187. will default to Regular Arming see section 15 1 5 4 4 Stay Arming Keyswitch SECTIONS 0601 To 0632 OPTION 6 Activating the keyswitch will bypass any zones defined as Stay Zones see section 4 5 3 in the selected partition All other zones will remain activated For more information on Stay Arming refer to section 15 2 5 4 5 Force Arming Keyswitch SECTIONS 0601 To 0632 OPTION 7 Activating the keyswitch will arm the selected partition bypassing any open zones defined as Force Zones see section 4 5 4 at the time of arming For more information on Force Arming refer to section 15 4 5 4 6 Instant Arming Keyswitch SECTIONS 0601 TO 0632 OPTION 8 This option is identical to Stay Arming except that all armed zones will become Instant Zones see section 4 3 4 For more information on Instant Arming refer to section 15 3 ES Only one of the arming options Stay Force Instant and Regular e can be selected DIGIPLEXNE CONTROL PANEL 17 ARMING AND DISARMING OPTIONS EE 6 1 ARMING FOLLOWS PARTITION Default disabled A partition can be set to follow the arming and disarming status of one or more partitions If a partition is set to follow more than one partition the partition will arm when all the selected partitions are armed However the partition will disarm as soon as one of the selected partitions is disarmed For example if options 2 and 3 are ON in section 3121 Partition 1 will au
188. y Key on the control panel s connector labeled MEM KEY Enter section 4010 to download the Memory Key s contents except sections 0001 to 0096 and 0501 to 0532 to the control panel 4011 to download the contents of the Memory Key including sections 0001 to 0096 and 0501 to 0532 to the control panel Control panel When the keypad emits a Confirmation Beep remove the Memory Key Figure 3 1 Using the Memory Key Jumper OFF Can copy and download Cannot override contents contents of the Memory Key of the Memory Key H Jumper ON 3 3 MODULE BROADCAST Keypads and other modules can also be programmed easily by using Module Broadcast see section 11 15 on page 33 Once a module is programmed its sections can be sent to other similar modules through the combus 3 4 PROGRAMMING THROUGH A KEYPAD Use the Programming Guide to record how the sections were programmed To enter programming mode Press and hold the 0 key Key in the INSTALLER CODE Default is 000000 Key in the 4 digit SECTION Key in required DATA Refer to the Programming Guide or to the corresponding sections in this manual ON For LCD Keypads The control panel will save the data and automatically advance to the next section or press the ENTER key to save the data and advance to the next section Press the CLEAR key to revert to the preceding step or to erase the current data entry For Grafica Keypads
189. y user 3 4A9 Keyswitch Close 3 4A3 Automatic Close 3 4A7 Remote arm disarm 1 4A4 Late to Close 1 4A4 Late to Close 1 456 Partial Arm 3 408 Quick arm 1 4A1 Open by user 1 4A1 Open by user 1 4A9 Keyswitch Open 1 4A1 Open by user 1 4A1 Open by user 1 4A1 Keyswitch Open 1 4A6 Open by user 1 4A6 Open by user 1 4A6 Keyswitch Open 1 464 Auto Arm Time Extended 1 4A7 Remote arm disarm 1 4A7 Remote arm disarm 1 408 Quick Disarm 1 57A Zone bypass 1 13A Burglary Alarm 1 11A Fire alarm 3 13A Burglary Alarm Restore 3 11A Fire alarm Restore 13A Burglary Alarm 13A Burglary Alarm 13A Burglary Alarm 13A Burglary Alarm 13A Burglary Alarm 13A Burglary Alarm 13A Burglary Alarm 13A Burglary Alarm 139 Burglary Alarm 12A Panic alarm 1AA Medical alarm 115 Pull Station 3 4AA Open Close 1 574 Group bypass 1 121 Duress 1 57A Zone bypass 1 144 Sensor tamper 3 144 Sensor tamper restore 1 421 Access denied 1 3A1 AC loss 1 3A9 Battery test failure 1 3AA System trouble 1 321 Bell 1 1 321 Bell 1 1 626 Time Date inaccurate 1 373 Fire trouble 3 351 Telco 1 fault restore Ad a mk mk mk mk mk mk mk mk Default SIA Report Code for sections 4032 to 4037 CL Closing Report CL Closing Report CS Closing Keyswitch CA Automatic Closing CQ Remote Arming OT Late to Close NA No Ac
190. zone s Group 8 CLock Loss The time and date were reset to default Step 1 Press the 8 key Step 2 Set the hour and minutes according to the 24 hour clock i e 9AM is 09 00 and 9PM is 21 00 Step 3 Enter the correct date according to yyyy mm dd Step 4 Press CLEAR to exit Press 8 to re program 3 Access during Clock Loss is ON section 3038 option 8 only the System Master Code and User Codes with the Master feature enabled will be able to program the clock Enter the System Master or a Master Code press TRBL then continue with the steps above If Access Control is enabled in the system and the option Door 15 13 TROUBLE LATCH SECTION 3033 OPTION 6 With the Trouble Latch feature disabled when a trouble occurs and is corrected the trouble is automatically cleared and no longer displayed With the Trouble Latch feature enabled the trouble will remain displayed until itis manually cleared by the user To clear the trouble the user must enter the trouble display see section 15 12 and then exit the trouble display For LCD and LED keypads press CLEAR to exit For Grafica keypads press the left action key Back to exit Only troubles that have been corrected can be cleared If a A trouble has not been corrected it will continue to be displayed even if the user tries to clear the trouble by using the method described above 15 14 CLEAR BELL CURRENT LIMIT TROUBLE SECTION

SEKURE DGP2-648 Installation manual

Contents

Download Pdf Manuals

Related Search

Related Contents