CORBERO LV 6031 Instruction manual
Contents
1. 3 To a stand pipe provided with vent hole minimum internal diameter 4 cm max 100 cm The waste connection must be at a height of between 30 cm minimum and 100 cm maximum from the bottom of the dishwasher The drain hose can face either to the right or left of the dishwasher Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water If you use a drain hose extension it must be no longer than 2 metres and its internal diameter must be no smaller than the diameter of the hose provided Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided min a S The sink plug must not be in place when the machine is draining as this could cause the water to siphon back into the machine Electrical connection Before plugging the appliance into the wall socket make sure that 1 The mains voltage corresponds to the voltage given in the Technical specifications 2 The meter fuses mains power supply and wall socket can all take the maximum load required Make sure that the socket and plug are compatible without having to use any type of adaptor If necessary have the domestic wiring system socket replaced Safety standards require the appliance to be2. 31 US33 CES09en Use of detergent Only use detergents specifically designed for use in dishwashers If using powder detergents proceed as follows 1 Open the dispenser lid by pulling the catch D 2 Add the detergent according to the recommendations in the programme chart As all detergents are not the same you should also consult the instructions on the packet 3 Always close the lid 4 If the programme has a prewash add the required detergent over the lid of the dispenser If using detergent in tablets proceed as follows 1 For all programmes place 1 tablet inside the detergent dispenser 2 Always close the lid 3 For all programmes with prewash place a portion of a further tablet on the lid of the detergent dispenser Insufficient quantities of detergent will Y produce poor washing results whereas an excessive amount of detergent will not improve washing results and is also wasteful Using no more than the correct amount also contributes to reducing pollution Compact detergents with enzymes In these low alkaline compact powders the environment unfriendly components have been replaced by natural enzymes and other more biodegradable substances These new compact powders are generally phosphate free As phosphates have water softening properties we suggest you add salt to the salt container even if the hardness of your water is as low as 4 dH 7 TH This will avoid li
3. MANUAL DE INSTRUCCIONES INSTRUCTION BOOKLET LAVAVAJ ILLAS DISHWASHER LV 6031 Attention The appliance which you have just bought is supplied not only with this instruction manual but also with a Warranty Card Certificate on the back of which are written the relative conditions Please fill in the necessary details on the Card Certificate and send it to the Corber Centre relative to the area in which the appliance is to be installed within twenty days of the date of purchase See list of Corber network centres We congratulate you on your choice Carefully read this instruction manual and follow attentively the recommendations it provides and thus benefit from years of excellent service The appliance which you have just purchased has been very accurately controlled throughout the entire manufacturing process Nevertheless should any problem arise during usage whether it be during the warranty period or when such period has expired please directly contact your nearest Corber Service Centre The address and telephone number of said Centre can be easily found in the enclosed List or by looking in the telephone directory under Corbero Our Corbero Service Network is at your complete disposal to serve you with maximum speed and efficiency all you have to do is call The products In order to obtain a good wash it is necessary to use detergents specially designed for dishwashers
4. Visible lime deposits or white film on the dishes Check that there is salt and that the salt cap is tight Check that the right level of the water softener is setted The dishes are not quite dry The rinse aid has run out or too little is being used The dishes are not clean poor wash The baskets are too full The dishes have not been arranged properly The spray arms do not rotate The spray arms are clogged The filters are clogged Then filters are not in position Not enough detergent has been used or it is unsuitable The detergent is old or has gone hard The salt container cap is not properly closed The washing programme selected is too gentle 38 RIMO5en If after all these checks the problem persists contact your local Service Force Centre quoting the model and serial number This information can be found on the rating plate located on the right hand side of the dishwasher door see picture Service and spare parts This product should be serviced by an i authorised Service engineer and only genuine spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Service Force Centre Always insist on genuine spare parts 39 RIM12en Hints for test centres before starting any test it is necessary to fill completel
5. earthed The manufacture accepts no liability for failure to observe the above safety precautions 73 23 of 19 2 73 Low Voltage Directive and subsequent modifications C This appliance complies with the following E E C Directives 89 336 of 3 5 89 Electromagnetic Compatibility Directive and subsequent modifications 42 COL03en Adjusting the worktop You can move the worktop forward or backward by 25 mm in order to align the machine with other kitchen units Simply unscrew the two rear retaining screws move the top to the required position and then retighten the screws Fitting under a counter kitchen worktop or sink By removing the machine s worktop you can install it under a close fitting sink unit or a pre existing top providing the dimensions of the recess correspond to those shown in the picture Proceed as follows Remove the machine s worktop by unscrewing the two rear retaining screws pull from the front and slide out the rear slots lifting the worktop Insert the machine after adjusting height and levelling with the adjustable feet When inserting the machine ensure that the water inlet and drain hoses are not kinked or squashed Levelling Good levelling is essential for correct closure and sealing of the door When the appliance is correctly levelled the door will not catch on the levelling spacers either side of the cabinet If the door does not close correctly loosen or tighte
6. door When the washing programme has finished it is recommended that the dishwasher is unplugged and the water tap turned off In general it is not advisable to open the door while the machine is working if the door is opened however a safety device ensures that the machine stops Caution Do not open the door during the hot phase this may cause hot water escape Care must be taken if the door is opened during the hot phase or immediately after a programme has finished as steam may escape SEQO9en Maintenance and cleaning Internal cleaning Ensure that the seals around the door the detergent and rinse aid dispensers are cleaned regularly with a damp cloth We recommend every 3 months to run a 65 C wash programme without dishes using detergen Cleaning the central filter After each wash Scraps of food may accumulate in the drain filter A and should be removed by rinsing the filter under running water To remove the drain filter simply pull it out by the handle Once cleaned refit the filter by pushing it back to its original position until it engages Cleaning the large filter Every month If necessary clean the large filter B on both sides under running water using a brush To remove the large filter 1 Remove the spray arm by pulling it upwards on one side 2 Turn the column C anticlockwise by 90 and then slide out the filter 3 Once cleaned refit it following the above inst
7. level 1 without using salt AA05 2AN l PDU06en Filling with salt Only use salt specifically designed for use in dishwashers All other types of salt not specifically designed for use in dishwasher especially table salt will damage the water softener Only fill with salt just before starting one of the complete washing programmes not the Rinse and Hold programme This will prevent any grains of salt or salty water which may have been spilled remaining on the bottom of the machine for any period of time which may cause corrosion To fill 1 To fill with salt unscrew the cap of the salt container 2 Pour 1 litre of water inside the container this is necessary only before filling with salt for the first time 3 Then using the funnel provided pour in the salt until the container is full Do not worry if water over flows from the unit when filling with salt this is quite normal 4 Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket 5 Screw on the cap tightly The salt container will require topping up periodically The salt cap has a refill indicator window in the centre A green float is clearly visible when there is salt inside the container and almost disappears when the salt has finished reminding you to add salt 28 SR11 SALO2en Rinse aid Rinse aid is automatically added during the last rinse
8. saucepans lids plates salad bowls cutlery etc Serving dishes and large lids should be arranged around the edge of the basket ensuring that the upper spray arm can turn freely The cutlery basket Long bladed knives stored in an upright VAN position are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket Take care when loading or unloading sharp items such as knives Cutlery should be placed in the removable cutlery basket with the handles facing downwards If the handles protrude from the bottom of the basket obstructing the lower spray arm load the cutlery with the handles facing upwards Mix spoons with other cutlery to prevent them from sticking together 30 Tr UI05 UI04 CES08en The upper basket The upper basket is designed for plates dessert plates saucers dinner plates of up to 24 cm in diameter salad bowls cups and glasses Arrange items on and underneath the fold down cup racks so that water can reach all surfaces Light items plastic bowls etc should be loaded in the upper basket and arranged so they do not move Before closing the door ensure that the spray arms can rotate freely After loading your machine always close the door as an open door can be a hazard
9. To ensure that your dishwasher functions perfectly Corber recommends using Calgonit System a unique and complete product tested by millions of householders Calgonit System includes Calgonit detergent rinse aid salt machine detergent and Citro Fresh It is able to fulfil the main requirements for clearing both the crockery and the machine itself 23 GAROten Contents For the user Important safety information Description of the appliance The control panel Before use Setting the water softener Rinse aid Using your appliance Loading your appliance Use of detergent Hints and tips Washing programmes Operating sequence Maintenance and cleaning Internal cleaning Cleaning the central filter Cleaning the large filter External cleaning Prolonged periods of non operation Frost precautions Moving the machine Something not working Service and spare parts Hints for test centres Technical specifications For the installer 25 Installation instructions 41 26 Water supply connections 41 Water outlet connection 42 26 Electrical connection 42 27 Adjusting the worktop 43 er Fitting under a counter 43 29 Levelling 43 30 Fitting a decor panel on the door 43 30 32 33 34 35 36 36 36 36 37 37 37 37 38 39 40 40 Guide to use the instruction book The following symbols will be found in the text to guide you throughout the instructions A 1 2 3 i Safety instructions Step
10. a special programme for quick washing a full load of lightly soiled dishes glasses and crockery except pots so that you may re use them promptly 34 PROO8en Operating sequence 1 Check the filters Ensure they are clean and properly positioned see Maintenance and cleaning 2 Check that there is rinse aid and salt 3 Load the dishes Remove any scraps of food Pull the lower basket out and arrange the saucepans plates and cutlery in it Pull the upper basket out and arrange the plates saucers glasses and cups etc in it Slide the baskets back into the machine 4 Ensure that the spray arms can rotate freely 5 Measure out detergent Add the required amount of detergent into the dispenser according to the Washing programmes chart Close the detergent dispenser lid 6 Close the dishwasher door 7 Set the programme Turn the programme selector dial clockwise until the letter of the programme you wish to select corresponds with the programme marker on the control panel 8 Start the programme Depress the On Off pushbutton The On Off indicator light will come on and the machine will start 35 10 At the end of the washing programme At the end of the programme the dishwasher will automatically stop The On Off indicator light remains on until the On Off pushbutton is depressed Switch off the dishwasher Switch off the dishwasher by pressing the On Off pushbutton and open the
11. by step Hints and tips Environmental information 24 INDO8en A Important safety information It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information This information has been provided in the interest of your safety You MUST read it carefully before installing or using the appliance Installation e This appliance is heavy Care should be taken when moving it Itis dangerous to alter the specifications or attempt to modify this product in any way e Care must be taken to ensure that the appliance does not stand on the electrical supply cable e Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person e Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person Child Safety e This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the product e Keep all packaging well away from children e Keep all detergents in a safe place out of children s reach During Use e items that are contaminate
12. d by petrol paint steel or iron debris corrosive acidic or alkaline chemicals must not be washed in this dishwasher e Under no circumstances should you open the door whilst the appliance is in operation Always turn off the appliance before opening the door e Only use detergent specifically designed for use in dishwashers e Long blades knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket e When finishing loading or unloading close the door as an open door can be a hazard 25 e Do not sit or stand on the open door e Isolate the appliance from the power supply and turn off the water supply after use e Care should be taken when cleaning the bottom door seal and hinge area as any exposed metal edges may cut if care is not taken e This product should be serviced by an authorised Service engineer and only genuine spare parts should be used e Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Service Force Centre Always insist on genuine spare parts Conservation In the interest of the environment e Materials marked with the symbol ZX are recyclable e Check with your local Council or Environmental Health Office to see if there are facilities in your area f
13. ensuring thorough rinsing spot and streak free drying The dispenser which is positioned inside the door holds about 110 ml of rinse aid which is sufficient for 16 40 dishwashing programmes depending upon the dosage setting Filling with rinse aid 1 Open the container by turning the lid A anticlockwise 2 Add the rinse aid until the container is completely full The indicator B will be completely dark 3 Top up the rinse aid when the indicator B because clear Ensure that the lid is closed after every refill Do not put liquid detergent in the rinse aid department Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash Adjusting the dose According to the finish and drying results obtained adjust the dose of rinse aid by means of the 6 position selector C position 1 minimum dosage position 6 maximum dosage Start from position 3 Gradually increase the dose if there are drops of water or lime spots on the dishes after washing Reduce it if there are sticky whitish streaks on the dishes 29 BROL BRIO1en Using your appliance Loading your appliance Before placing dishes in the machine remove any scraps of food to avoid clogging the filters and consequently reducing the performance Do not load very small items which can fall through the baskets The lower basket The lower basket is designed to take
14. me deposits on crockery and the inner tub 32 DETO3en Hints and tips To save energy Place dishes in the machine immediately after every meal and wait until the dishwasher is full before washing lf necessary run the Rinse and Hold programme see Washing Programmes chart so that any food scraps do not become caked on the dishes while you are waiting to run the complete wash programme Do not prewash dishes under running water Select a quick programme when dishes are not very soiled following the instructions given in the Washing programmes chart For best washing and drying results Before loading remove all scraps of food and soak very heavily soiled pots and pans Arrange saucepans cups and glasses etc upside down Tilt items with convex or concave surfaces so that the water drains off easily Avoid contact between the dishes as far as possible Wait a few minutes before removing the dishes in this way they will be cooler and the drying will be improved Empty the lower basket first and then the upper one this will avoid water dripping from the upper basket onto the dishes in the lower one You will improve drying results by leaving the dishwasher door ajar for at least 15 30 minutes as soon as the programme finishes 33 Items not suitable for dishwashers The following items should not be washed in the dishwasher unless they are sold as dishwasher proof Cutle
15. n the adjustable feet until the machine is perfectly level Fitting a decor panel on the door The door of this machine has frames for fitting a plastic laminate decor panel in the colour required to match the dishwasher with the rest of the kitchen furniture If you wish to do this you must provide the panel yourself that must have the following dimensions Width 588 mm Height 586 mm Max thickness 4mm To fit the panel Take the door frame off after removing the retaining screws around the edge Position the panel refit the frame and tighten the retaining screws around the edge Note The panel should be fitted before positioning the machine 43 IN05 INS08en Corbero 152988 65 0 sid Total Chlorine free amp 0 0599
16. or re cycling this appliance e When the appliance is to be scrapped cut off the power supply cable and make the door closing device unusable to prevent young children from being trapped inside e Help to keep your country tidy use authorised disposal sites for your old appliance AVVO1en Description of the appliance Water hardness adjustment Levelling spacers Upper basket stop Salt container Large filter Detergent dispenser Control panel Rating plate O0 0o N ea fF Se No Rinse aid dispenser oOo Central filter gt _ Lower spray arm N Upper spray arm oo Upper basket Worktop _ gt The control panel MARCHA DU TAA A NORMAL CON PRELAVADO 65 C B CICLO BREVE 65 C lt gt C REMOJO i 1 2 3 4 1 On Off indicator light 7 Programme sequence indicator As the programme progresses the programme selector dial turns to show the phase in the 3 Programme guide wash programme the appliance has reached 2 On Off pushbutton 4 Door handle ity Prewash Rinse and hold 5 Programme marker m Wash im Cold rinse 6 Programme selector dial a 3x Hot rinse J Drying 26 APP12en Before use Before using your dishwasher for the first time 1 ensure that the electrical and water connections comply with the installation instructions 2 remove all packaging f
17. rom inside the appliance 3 set the water softener 4 pour 1 litre of water inside the salt container and then fill with salt 5 fill the rinse aid dispenser Setting the water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply which would have a detrimental or adverse effect on the operation of the appliance The higher the content of these salts the harder your water is Water hardness is measured in equivalent scales German French degrees and PPM parts per Million The softener should be adjusted according to the hardness of the water in your area Your local Water Authority can advise you on the hardness of the water in your area The dishwasher is factory set at level 2 If this level is not suitable for your area the softener should be adjusted To adjust the water softener With a screwdriver turn the selector on the upper front corner of the machine until the level required corresponds with the marker 27 Water hardness German French PPM degrees degrees Parts per Level Use of dH TH Million salt 0 4 0 7 0 80 0 NO 5 11 8 25 81 200 1 YES 12 22 26 40 201 400 2 YES 23 34 41 60 401 600 3 YES 35 50 61 90 601 900 4 YES 51 67 91 120 901 1200 5 YES i If your water is level 0 it is already soft and therefore there is no need to use salt In this case adjust the water softener on
18. rtheless we advise you a cold water supply A hot water supply is not always efficient with very soiled crockery as it shortens the washing programmes Feeding the appliance with a hot water supply max 60 C will allow you to obtain considerably shorter programmes The water pressure must be within the limits given in the technical specifications Your local Water Authority will advise you on the average mains pressure in your area The dishwasher features fill and drain hoses which can be turned either to the left or the right to suit the installation The locknut must be correctly fitted to avoid water leaks Avoid bends or kinks in the hose which could prevent or slow down the water supply If the machine is connected to new pipes or pipes which have not been used for a long time you should run the water for a few minutes before connecting the inlet hose This will prevent deposits of sand or rust clogging the inlet hose filter For making the connection itself the coupling nut fitted to the machine s supply hose is designed to screw onto either a 3 4 inch gas thread spout or to a purpose made quick coupling tap such as the Press block 41 COL04en Water outlet hose connection The end of the drain hose can be connected in the following ways 1 To the sink outlet siphon securing it if necessary with a clip 2 Hooked over the edge of the sink using the special curved plastic guide provided
19. ructions in reverse order 4 Ensure the filter is in its original position the handle of the drain filter should be pointing towards the front of the appliance The dishwasher must not be used without filters Incorrect repositioning and fitting of the filters will produce poor washing results Cleaning the filters is vital to ensure correct operation of the machine 36 MANO1en External cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth If necessary use only neutral detergents Never use abrasive products scouring pads or solvent acetone trichloroethylene etc Prolonged periods of non operation If you are not using the machine for any period of time you are advised to 1 Unplug the appliance and then turn off the water 2 Fill the rinse aid dispenser 3 Leave the door ajar to prevent the formation of any unpleasant smells 4 Leave the inside of the machine clean Frost precautions Avoid placing the machine in a location where the temperature is below 0 C If this is unavoidable empty the machine close the appliance door disconnect the water inlet pipe and empty it Moving the machine If you have to move the machine moving house etc 1 Unplug it 2 Turn the water tap off 3 Remove the water inlet and discharge hoses 4 Pull the machine out together with the hoses Avoid over tilting the machine during tran
20. ry with wooden or horn handles or glued parts bronze cutlery saucepans with wooden handles aluminium ware crystal ware leaded glass plastic items antique or fine decorated china Certain types of decoration can discolour when washed in a dishwasher Crystal ware and plastic objects if not guaranteed dishwasher proof should be washed by hand Certain types of glass can also become opaque after being washed several times in a dishwasher A chemical reaction can occur between silver cutlery and stainless steel cutlery As a precaution do not wash together Iron and cast iron objects can rust and stain other items Aluminium tends to go black copper pewter and brass tend to stain If in doubt check with manufacturer of the item When buying new dishes ensure that they are dishwasher proof CON04en Washing programmes Programme Degree of soil Starting position Required ee Cycle and of the programme pushbuttons npe a the description type of load selector dispenser dispenser I Normal oS Normal soll Main wash up to 65 C ormal soll 25 5 with Crockery and cutlery A On Off 9 9 2 cold rinses prewash 1 hot rinse x Light soil Main wash up to 65 C SER ash Crockery and B On Off 25g 1 cold rinse party crockery 1 hot rinse Ri d Any 1 cold rinse to avoid inse an Partial load to be food scraps from sticking Hold completed later in the C On Off together day This is
21. sport 37 MANO3en Something not working Certain problems are due to lack of simple maintenance or oversights which can be solved easily without calling out an engineer Before contacting your local Service Force Centre please carry out the checks listed below Symptom Solution The machine will not start The door has not been properly closed The plug is not properly inserted in the power socket There is no current at the socket The machine does not fill with water Ensure the water tap is open Ensure the mains water supply has not been cut off The inlet hose may be squashed or bent Reposition the hose The inlet hose may be blocked Switch off the water supply and clean the filter The filters are blocked Clean the filters refer to Maintenance and cleaning The spray arms are not rotating Ensure the crockery is loaded correctly The dishwasher will not drain The machine is noisy The drain hose may be squashed or bent Reposition the hose The sink may be blocked Clear any blockages The drain hose extension is not correct Follow the instructions for connecting to the waste There is no vent in the end of the drain hose Dishes are rattling against each other refer to Loading your machine The spray arms are knocking against the dishes Refer to Loading your machine The door is difficult to close The dishwasher is not level or not properly built in
22. y with salt the salt container and with rinse aid the rinse aid dispenser Test standard EN 50242 Reference programme Normal 65 C with prewash Load 12 standard place settings Rinse aid selector position 5 Detergent dosage 25 g in the dispenser 5 g on the dispenser lid Arrangement upper basket Technical specifications ula Arrangement lower basket DIMENSIONS Width 60 cm Height with worktop 85 cm Height without worktop 82 cm Max depth 60 cm Max depth with open door 115 2 cm ELECTRICAL CONNECTION Voltage 220 230 V 50 Hz MOTOR RATING DURING WASH 200 W POWER OF HEATING ELEMENT 2100 W OVERALL POWER 2300 W WATER SUPPLY PRESSURE Minimum 50 kPa 0 5 bar Maximum 800 kPa 8 bar CAPACITY 12 place settings 40 ISTO7en Installation instructions Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person Remove all packaging before positioning the machine If possible position the machine next to a water tap and a drain Water supply connections This dishwasher may be fed with either hot max 60 C or cold water Neve
Download Pdf Manuals
Related Search