User Guide
Contents
1. aS LINKABLE REMO TE 112 SETTING IM 250 SP User Guide Please read these instructions carefully before use TABLE OF CONTENTS 1 Safety Instruction 2 Technical Specification 2 1 Description of the fixture 2 2 Inserting Exchanging rotating gobos 3 Lamp 4 How To Set The Unit 4 1 Control Panel 4 2 Main Function 4 3 Home Position Adjustment 4 4 Easy controller 5 How To Control The Unit 5 1 DMX Controller 5 2 DMX 512 Configuration 5 3 DMX 512 Connection 6 Troubleshooting 7 Maintenance and Cleaning 1 Safety Instruction A N Please read carefully the instruction which includes important WARNING information about the installation usage and maintenance Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit The unit is designed for use with the HMQ 250 2G lamps Do not use any other type of lamp ts important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure2. ESC To go back to the previous functions ENTER To confirm the selected functions JOG WHEEL To select the given functions On Off Turns On Off the power Fuse To replace the fuse DMX input output For DMX 512 operation use 3 5 pin XLR plug cable to link the unit together Sensitivity To receives audio signal for sound activation Only for remote control By connect to the 1 4 microphone jack to control the unit for Stand by Function and Mode function 4 2 Main Function To select any of the pre set functions press the ENTER button and turn jog wheel up to when the required one is shown on the monitor Select the function by ENTER button Use the jog wheel to change the mode Once the required mode has been selected press the ENTER button to setup or it will automatically return to the main functions without any change after idling 10 seconds To go back to the previous functions without any change press the ESC button The main functions are shown below 9A 1 r1 DMX Address H I DMX512 Addressing 1 r 16Channel Setting 16 Channel Channel Mode lt 22 Channel Setting 22 Channel Yes StandB H StandBy Mode ves y H No No StandBy Show Mode Lt Show Mode 1 4 1 Slave
3. Ballast Ignitor connector A As the picture above if the cable or cable joints turned yellow or black please replace the cable or cable joints immediately B Do maintain the fixtures every two months and make sure that all the screws and terminals have been locked to make sure the normal performance of the fixtures Negligence of maintenance would cause malfunction of the fixture Cleaning The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days 25A EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN 60598 1 2004 IEC 60598 1 2003 corrigendum 2004 Part 1 General requirements and test Following the provisions of the low vol
4. Gobo wheel Fixed gobo wheel 1 5 rotating interchangeable indexing gobos plus open Rotating gobo wheel 2 7 metal gobos plus open Magnetic Gobo wheels home positioning for easy calibration and easy maintenance Both rotate in both directions at different speeds creating shaking effect Effect Wheel Prism Rotating Prism Movement Pan 540 2 8 second Tilt 270 in 1 6 second Pan Tilt resolution 8 16 bit Automatic Pan Tilt correction Electronic sensor Pan Tilt home positioning for easy calibration and easy maintenance Pan Tilt position lock for transporting protection Focus Automatic focus by DMX controls Iris Motorized iris for different beam diameters Iris Speed control 4A DMX Channels Standard DMX512 signal addressing and can be controlled by any universal DMX controller or DMX Tester 22 Channels Channel 1 Pan Channel 12 Prism Channel 2 Tilt Channel 13 Prism Rotation Channel 3 Pan Tilt speed Channel 14 Focus Channel 4 Dimmer Channel 15 Iris Channel 5 Shutter shaking Channel 16 Lamp ON OFF Reset Channel 6 Color 1 Channel 17 Pan movement fine Channel 7 Color 2 Channel 18 Tilt movement fine Channel 8 Gobo 1 Channel 19 Pan Tilt movement macro Channel 9 Gobo 1 Rotation Channel 20 Pan Tilt movement size Channel 10 Gobo 2 Channel 21 Iris effect Channel
5. fixture within 15 minutes until the unit cools down after switching off WARNING Because of its high internal pressure there might be a risk that the Discharge lamp would explode during operation The lamp emits intense UV radiation which is harmful to the eyes and skin The high luminance of the arc can cause severe damage to the retina if looks directly at the lamp HMQ 250 2G 1 Always switch off the main supply and never handle the lamp or luminaire when it is hot 2 Do not touch the bulb with bare hands If this happens clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation 3 The lamp generates UV radiation Never operate the lamp without appropriate shielding 4 When burning the lamp operates at high pressure and there is a slight risk of arc tube rupture The risk increases with age temperature and improper handling of the lamp Do not use the lamp any longer than its lifespan 5 Make sure the lamp is located in the center of the reflector for the best spot 6 If changing the lamp remove old lamp from lamp socket Hold the new lamp only by its ceramic base Never touch the glass bulb Insert the new lamp in the lamp socket 7A 4 How To Set The Unit 4 1 Control Panel MONITOR To show the various menus LED DMX On DMX input present MASTER On Master Mode SLAVE On Slave Mode SOUND Blinking Sound Mode 8A Button
6. ENTER button to setup or automatically return to the offset functions without any change press the ESC button To go back to the main functions without any change after 10 seconds lris offset Press the ENTER button for at least 12 seconds into offset mode turn jog wheel up to when the Iris offset is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to adjust the iris home position Once the position has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the ESC button To go back to the main functions without any change after 10 seconds Focus offset Press the ENTER button for at least 12 seconds into offset mode turn jog wheel up to when the Focus offset is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to adjust the iris home position Once the position has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the ESC button To go back to the main functions without any change after 10 seconds 4 4 Easy Controller The easy remote control is used only in master slave mode By connecting to the 1 4 microphone jack of the first unit you will find that 2 gt the remote control on the first unit will control all the other units for Stand f 3 by Function Mode e
7. back to the previous functions without any change press the ESC button Software Version Press the ENTER button and turn jog wheel up to when the Software Version is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to select the A or B or C or D mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 10 seconds To go back to the previous functions without any change press the ESC button 13A Reset Press the ENTER button and turn jog wheel up to when the Reset is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to select the Yes or No mode select Yes option and all channels of the unit will return to their standard position To go back to the main functions press the ESC button twice 4 3 Home Position Adjustment Press ENTER button into main function and then press ENTER button for at least 12 seconds into offset mode to adjust the home position when you want to adjust gobo and color home position you should be run Adjust Focus mode first the functions are shown below Adjust Focus H Focus Adjust 0 255 255 0 Offsel Offset 0 255 PanOffset 255 Pan Offset 0 255 TilOffset H Tilt Offset O 255 255 Dimmer Offset _ Dimmer
8. connectors can easily distort the signal and shut down the system 4 The DMX output and input connectors are pass through to maintain the DMX circuit when power is disconnected to the unit 5 Each lighting unit needs to have a DMX address to receive the data by the controller The address number is between 0 511 usually 0 amp 1 are equal to 1 6 The end of the DMX 512 system should be terminated to reduce signal errors 7 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 22A 6 Troubleshooting Following few common problems that may occur during operation are some suggestions for easy troubleshooting A The unit does not work no light and the fan does not work 1 Check the connect power and main fuse 2 Measure the mains voltage on the main connector 3 Check the power on LED B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 If the DMX LED is on and no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the unit or the previous one 4 Try to use another DMX controller 5 Check to see if the DMX cables run near or run alongside to high voltage cables that ma
9. that no ventilation slots are blocked Disconnect main power before fuse lamp replacement or servicing Replace fuse lamp only with the same type Make sure there are no flammable materials close to the unit while operating as it is fire hazard Please use safety chain while you fixing this unit Don t handle the unit by taking its head only but always by taking its base Maximum ambient temperature is ta 40 C Don t operate it where the temperature is higher than this Unit surface temperature may reach up to 85 C Don t touch the housing bare hand during its operation and allow about 15 minutes to cool down before replacing bulb or serving as the unit could be very hot Inthe event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Don t connect the device to any dimmer pack Do not touch any wire during operating as there might be a hazard of electric shock 2A Warning To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture Never touch bulb with bare fingers as it is very hot after using Hotlamp explosion hazard Do not open the unit within five minutes after switching off Donotstart on the u
10. the ENTER button to setup or automatically return to the main functions without any change after 10 seconds To go back to the previous functions without any change press the ESC button Tilt Inversion Press the ENTER button and turn jog wheel up to when the Tilt Inversion is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to select the Normal or Inversion mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 10 seconds To go back to the previous functions without any change press the ESC button Auto Test Press the ENTER button and turn jog wheel up to when the Auto Test is shown on the monitor Pressing ENTER button and the display will blink select option and the unit will run self test by built in program To go back to the main functions press the ESC button twice Manual Test Press the ENTER button and turn jog wheel up to when the Manual Test is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to select the Pan or Tilt or Shutter or mode Once the mode has been selected press the ENTER button and use jog wheel to select the 0 255 value Once the value has been selected press the ENTER button to setup or automatically return to the main functions 12A without any change after 10 seconds To go back t
11. 00 007 Blackout 000 018 000 021 000 009 White Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 Channel 15 i MT UM 255 Slow 200 209 Reset 232 255 Macro 10 fixture 230 239 Lamp off 208 231 9 130 139 Lamp on 184 207 Macro 8 120 129 disable shutter off while jobo1 or gobo2 192 Fast 160 183 Macro 7 B 110 119 shutter off while gobo or gobo2 112 135 Macro 5 change 096 111 100 109 disable 088 111 Macro 4 shutter off while 080 095 color1 or color2 128 Slow 064 087 Macro 3 128 Slow change 064 079 090 099 enable 040 063 Macro 2 157 Prism 250 shutter off while 5 colcor1 or color2 change 191 Fast 136 159 Macro 6 127 Gobot Index 360 048 063 016 039 Macro 1 080 089 disable 032 047 008 015 Prism shutter off while pan or tilt move 016 031 000 007 No prism 070 079 enable 000 Gobo Index 0 No macro 000 Pri x 0 shutter off while 000 015 pan ortilt move G8 G9 G10 G11 G12 0eo6000 2 G3 4 Q 5 G6 20A 22 Channels DMX 512 Configuration 2 Pan movement Tilt movement Pan Tilt Pan Tilt fine fine movement macro movement size 248 255 Macro 16 240 247 Macro 20 232 239 Macro 19 Shutter open Fast 224 231 Macro 18 Open 216 223 Macro 17 208 215 16 aw 200 207 Macro 20 Fast 192 199 Macro 19 184 191 Macro 18 Max 176 183 Macro 17 ul 168 175 Macro 16 160 167 Macro 20 152
12. 11 No function Channel 22 Dimmer effect 16 Channels Channel 1 Pan Channel 9 Gobo 1 Rotation Channel 2 Tilt Channel 10 Gobo 2 Channel 3 Pan Tilt Speed Channel 11 No function Channel 4 Dimmer Channel 12 Prism Channel 5 Shutter shaking Channel 13 Prism Rotation Channel 6 Color 1 Channel 14 Focus Channel 7 Color 2 Channel 15 Iris Channel 8 Gobo 1 Channel 16 Lamp ON OFF Reset Dimension 402 x 362 x 583 mm Weight 25 kg 583 5A Luminous intensity 0 44 1 5 15 0 Ei 0 44 a 145 0 5 itt 10 Distance m 1 Yoke 2 Front panel 3 Moving head 4 Handle 5 Base 2 Inserting Exchanging rotating gobos DANGER Install the gobos with the device switched off only Unplug from mains before changing gobos Open the cover by loosening the fastening screw at the sides of the cover If you wish to use other forms and patterns as the standard gobos or if the gobos are to be exchanged remove the fixation ring with an appropriate tool Remove the gobo and insert the new gobo Press the fixation ring together and insert it in the front of the gobo 6A CAUTION Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened 1 In case of replacement of the lamp or maintenance do not open the
13. 128 Slow 110 119 enable 191 Fast 112 127 136 159 6 shutter off while gobo or gobo2 096 111 112 135 Macro 5 change 100 109 disable 088 111 Macro 4 shutter off while 080 095 color1 or color2 128 Slow 064 087 Macro 3 128 Slow change 064 079 090 099 enable 040 063 Macro 2 n shutter off while 127 Prism Index 360 048 063 colcor1 or color2 016 039 Macro 1 change 080 089 disable Q REST 008 015 Prism shutter off while pan or tilt move 016 031 No prism 070 079 enable 000 Gobo Index 0 000 007 Nomacro 000 Prism index o shutter offwhile 000 015 pan ortilt move Gobo Index 360 2 3 4 G8 G9 G10 611 612 2606 Q Q Q Q 5 G6 Qe 19A 22 Channels DMX 512 Configuration 1 Pan Tilt Speedieelection ome Sen 255 p Slow 255 p 100 248 255 Open 248 255 Macro6 240 247 Random 240 247 5 strobe 232 239 Macro4 239 Fast shaking 224 231 Macro3 gobo2 216 223 Macro2 186 Slow shaking 208 215 1 Fast gobo2 207 Slow 185 Fast shaking gobo1 C 128 Slow 132 Slow shaking gobot 128 Slow 131 Fast strobe 064 127 Position 17 055 063 Green O 085 105 AAH 128 Slow 046 054 Blue 114 127 Frost 064 084 037 045 095 113 3200K 016 Slowstrobe 028 036 Magenta 076 094 UV Purple 043 063 057 075 Light green 008 015 Open 019 027 Lightyellow 038 056 Pink 022 042 010 018 Red 019 037 Light Blue 0 B Fast 0 0 0
14. 159 Macro 19 144 151 Macro 18 Close 136 143 Macro 17 Slow 128 135 Macro 16 i Slow 120 127 Macro 15 112 119 Macro 14 Open 104 111 Macro 13 096 103 Macro 12 088 095 Macro 11 080 087 Macro 10 072 079 Macro9 064 071 Macro 8 056 063 Macro7 048 055 Macro6 040 047 Macro 5 Close 032 039 Macro4 Max Max 024 031 Macro3 008 TN 008 Fast 016 023 Macro 2 008 015 Macro 1 000 007 nomacro 000 007 no macro 000 007 No Macro 2 a ea 16 BIT TILT 21A 5 3 DMX512 Connection The DMX 512 is widely used in intelligent lighting control with a maximum of 512 channels INPUT OUTPUT COMMON INPUT OUTPUT DMX Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 If you use a controller with 5 pins DMX connector you need to use a 5 to pin adapter 2 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug cable from the output of the unit to the input of the next unit The cable cannot be branched or split to a Y cable DMX 512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded
15. Mode Normal Slave Mode 2 Slave Mode 2 light show z 1 0 Adjust Focus 1 Focus Adjust 0 255 E A ll 255 I AdjustFocus2 L0 _ Focus Adjust 0 255 255 Normal Pan Normal r Pan Inverse Pan Inverse Normal Tilt Normal Tilt Inverse mema Inverse Tilt Inverse Auto Test Self Test MENU ee Pan Pan 0 255 m Tilt Tilt 0 255 Shutter Shutter 0 255 Color1 Color1 0 255 1 Color2 Color2 0 255 LIC Gobo1 Gobo1 0 255 Bane ee R Gobot R Gobo1 0 255 t ___ Gobo2 Gobo2 0 255 i Prism Prism 0 255 R Prism R Prism 0 255 Focus Focus 07255 Iris Iris 07255 Lamp Temperature Ambient Temperature of lamp I 4 Lamp Hours Lamp Hours Yes Lamp On I Lamp On Off _ No Lamp Off On Lamp On Power On Lamp On Power On Off Lamp Off Power Off m Software Version Software Version Rest Reset No Non Reset DMX 512 Address Setting Press the ENTER button and turn jog wheel up to when the DMX Address is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to change the DMX 512 address Once the address has been selected press the ENTER button to setup or automatically return to the main functions without any change after 10 seconds To go back to the previous functions without any change press the ESC button 10A Channel Mode Press the ENTER button and turn jog wheel up to when the Ch
16. Offset 0 255 25 H Color Offiset H Color Offset 127 127 127 Color2 Offset 1 Color2 Offset 127 127 127 127 MENU Gobo Offset j 1 Gobo2 Offset 127 127 R Gobo Offset R Gobo Offset 127 127 Gobo Offset j Gobo Offset 127 127 PismOffset Prism Offset 0 255 R Prism Offset R Effect Offset 127 127 Iris Offset Iris Offset 0 255 Ss f Focus Offset 4 Focus Offset 0 255 Adjust Focus Press the ENTER button for at least 12 seconds into offset mode turn jog wheel up to when the Adjust Focus is shown on the monitor Pressing ENTER button and the display will blink The unit will focus on tilt 135 and then the unit will focus on tilt 45 pan 90 pan 180 pan 270 in every pressing ENTER button Once the focus has been selected use jog wheel to adjust this settings only for offset mode to adjust home position To go back to the previous functions without any change press ESC button 14A Pan offset Press the ENTER button for at least 12 seconds into offset mode turn jog wheel up to when the Pan offset is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to adjust the pan home position Once the position has been selected press the ENTER button to setup or automatically
17. annel Mode is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to select the 16 Channel or 22 Channel mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 10 seconds To go back to the previous functions without any change press the ESC button StandBy Mode Press the ENTER button and turn jog wheel up to when the StandBy Mode is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to select the yes standby or no standby Mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 10 seconds To go back to the previous functions without any change press the ESC button Show Mode Press the ENTER button and turn jog wheel up to when the Show Mode is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to change the Show Mode 1 4 Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 10 seconds To go back to the previous functions without any change press the ESC button Slave Mode Press the ENTER button and turn jog wheel up to when the Slave Mode is shown on the monitor Pressing ENTER button and the display will blink U
18. cally return to the offset functions without any change press the ESC button To go back to the main functions without any change after 10 seconds Color 2 offset Press the ENTER button for at least 12 seconds into offset mode turn jog wheel up to when the Color 2 offset is shown on the monitor Pressing ENTER button and the 15A display will blink Use jog wheel to adjust the color 2 home position Once the color has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the ESC button To go back to the main functions without any change after 10 seconds Gobo 1 offset Press the ENTER button for at least 12 seconds into offset mode turn jog wheel up to when the Gobo 1 offset is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to adjust the gobo 1 home position Once the gobo has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the ESC button To go back to the main functions without any change after 10 seconds R Gobo 1 offset Press the ENTER button for at least 12 seconds into offset mode turn jog wheel up to when the R Gobo 1 offset is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to adjust the R gobo 1 home position Once the R gobo has been selected press the ENTER button to
19. hange after 10 seconds To go back to the previous functions without any change press the ESC button Please refer to the following diagram to address your DMX512 channel for the first 4 units Mode Fixture 1 Fixture 2 Fixture 3 Fixture 4 16 CH 1 17 33 49 22 CH 1 23 45 67 18A 16 Channels DMX 512 Configuration Pan Tilt speed setechon 255 p Slow 255 100 248 255 Open 248 255 Macro6 240 247 Random 240 247 5 strobe 232 239 4 239 Fast shaking 224 231 Macro gobo2 Fast 216 223 2 186 Slow shaking 208 215 Macro 1 gobo2 207 Slow 185 Fast shaking C gobot OO 128 Slow 132 Slow shaking goboi 128 Slow 131 Fast strobe 064 127 Position 055 063 Green 0 085 105 AAHH 128 Slow 046 054 Blue 114 127 Frost 064 084 037 045 095 113 3200 016 Slowstrobe 028 036 Magenta 076 094 UV Purple 043 063 057 075 Light green 008 015 Open 019 027 Lightyellow 038 056 Pink 022 042 010 018 Red 019 037 Light Blue on Fast OR 0 000007 000 018 White 000 021 000 009 White Channel 9 Channel 10 Channel 11 Channel 12 Channel 13 Channel 14 200 209 Reset 255 Slow Nine 255 Slow 232 255 Macro 10 Slow 255 230 239 Lamp off 208 231 9 O 130 139 Lamp on 184 207 Macro 8 120 129 disable P shutter off while jobo1 or gobo2 192 Fast 160 183 Macro 7
20. ms j 17A Stand by Blackout the unit Function Strobe 1 Sync strobe 2 Two light strobe 3 Sound strobe X Y moving show pattern selection Show 1 Show 4 Please refer to 4 2 Main Functions Show mode Gobo Color selection 1 Hold on for gobo selection 2 Press for color change X Y moving setting 1 Pan position 2 Tilt position 3 Dimmer First set Master unit then set Slave units position Mode Sound 1 LED off Sound 2 LED slow blinking Slow Sound 3 LED on Position Latch LED fast blinking 5 How To Control The Unit You can operate the unit by universal DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once on the monitor and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal 5 1 DMX Controller If you use a universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal Press the ENTER button up to when the DMX address is shown on the monitor Pressing ENTER button and the monitor will blink Use jog wheel to change the DMX512 address Once the address has been selected press the ENTER button to setup or automatically return to the main functions without any c
21. nit without bulb enclosure or when housing is damaged The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Donotlook directly at the light while the bulb is on Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs by yourself In the unlikely event your unit may require service please contact your nearest dealer Installation The unit should be mounted via its mounting system as shown below on the bottom of the base Use clamps to fix the unit to truss Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 50 kg for each unit Safety chain m Em y 3 1 74 p 3A 2 Technical Specification Power supply 120V 230V 50 60Hz Lamp HMQ 250 2G Optical system High efficiency optical system High quality optical lens and dichroic colors Beam angle 15 Shutter Dimmer Blackout 0 100 smooth dimming and strobe speed variable 1 12 flashes per second Color wheel Color wheel 1 6 color white Color wheel 2 7 trapezoid dichroic colors plus white Both rotate in both directions at different speeds creating rainbow effect Magnetic Color wheels home positioning for easy calibration and easy maintenance
22. o the previous functions without any change press the ESC button Lamp Temperature Press the ENTER button and turn jog wheel up to when the Lamp Temperature is shown on the monitor Pressing ENTER button and the ambient temperature of lamp will show on the monitor To go back to the main functions press the ESC button twice Lamp Hours Press the ENTER button and turn jog wheel up to when the Lamp Hours is shown on the monitor Pressing ENTER button and the monitor will show the number of working hours of the unit To go back to the main functions press the ESC button twice Lamp On Off Press the ENTER button and turn jog wheel up to when the Lamp On Off is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to select the Lamp on or Lamp off mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 10 seconds To go back to the previous functions without any change press the ESC button Lamp On Power On Press the ENTER button and turn jog wheel up to when the Lamp On Power On S shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to select the on or off mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 10 seconds To go
23. return to the offset functions without any change press the ESC button To go back to the main functions without any change after 10 seconds Tilt offset Press the ENTER button for at least 12 seconds into offset mode turn jog wheel up to when the Tilt offset is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to adjust the tilt home position Once the position has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the ESC button To go back to the main functions without any change after 10 seconds Dimmer offset Press the ENTER button for at least 12 seconds into offset mode turn jog wheel up to when the Dimmer offset is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to adjust the dimmer home position Once the position has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the ESC button To go back to the main functions without any change after 10 seconds Color 1 offset Press the ENTER button for at least 12 seconds into offset mode turn jog wheel up to when the Color 1 offset is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to adjust the color 1 home position Once the color has been selected press the ENTER button to setup or automati
24. se jog wheel to select the Normal or 2 light show Mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 10 seconds To go back to the previous functions without any change press the ESC button Adjust Focus 1 Press the ENTER button and turn jog wheel up to when the Adjust Focus 1 is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to change the focus 1 0 255 Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 10 seconds To go back 11A to the previous functions without any change press the ESC button Adjust Focus 2 Press the ENTER button and turn jog wheel up to when the Adjust Focus 2 is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to change the focus 2 0 255 Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 10 seconds To go back to the previous functions without any change press the ESC button Pan Inversion Press the ENTER button and turn jog wheel up to when the Pan Inversion is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to select Normal or Inversion mode Once the mode has been selected press
25. setup or automatically return to the offset functions without any change press the ESC button To go back to the main functions without any change after 10 seconds Gobo 2 offset Press the ENTER button for at least 12 seconds into offset mode turn jog wheel up to when the Gobo 2 offset is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to adjust the gobo 2 home position Once the gobo has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the ESC button To go back to the main functions without any change after 10 seconds Prism offset Press the ENTER button for at least 12 seconds into offset mode turn jog wheel up to when the Prism offset is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to adjust the prism home position Once the prism has been selected press the ENTER button to setup or automatically return to the offset functions without any change press the ESC button To go back to the main functions without any 16A change after 10 seconds R Effect offset Press the ENTER button for at least 12 seconds into offset mode turn jog wheel up to when the R Effect offset is shown on the monitor Pressing ENTER button and the display will blink Use jog wheel to adjust the R Effect home position Once the R effect has been selected press the
26. tage directive 73 23 EEC and 93 68 EEC Innovation Quality Performance 26A
27. y cause damage or interference to DMX interface circuit C No response to the sound 1 Make sure the unit is not receiving DMX signal 2 Check microphone to see if it is good by tapping the microphone D One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition E The lamp is cutting out intermittently 1 Thelamp is not working well Check the main voltage either too high or too low 2 Internal temperature may be too high Check and if necessary replace the fan on the head F If The pan belt is broken 1 Turn off the main power 2 Unscrew all the screws A and open the base housing cover B 23A 3 Unplug all the connect wires that upon belt 4 Change a new belt C put the belt around the axis gear and motor gear 5 Install the new belt and adjust the belt tension properly Note do not fix the belt too tight as it is easy to rupture 6 Plug all the connect wires back that upon belt 7 Screw all the screws A G If The tilt belt is broken 1 Turn off the main power 2 Unscrew all the screws A and open the right arm cover B 3 Change a new belt C Please adjust the tension of the belt properly Note do not fix the belt too tight as it is easy to rupture 4 Screw all the screws A 24A 7 Maintenance Cleaning Maintenance oco e ee
Download Pdf Manuals
Related Search