Peavey 680S User's Manual
Contents
1. Fi m TAPE RECORDER aa a TK SE di OUT OUT FOOTSWITCH On Off for POWER AMP Internal Effects Voy MAIN PA XRD 680S Plus external EQs and power amps for mains Internal EQ and power amps for monitors POWER AMP 0 nil lt Voy Ko MAIN PA FOOTSWITCH On Off for Internal Effects ES CD PLAYER LOW Z TAPE RECORDER XRD 6805 Plus internal EQ and power amp for mains mono External EQ and internal power amp for monitors TO LEFT SPEAKER JACK TO RIGHT Dee SPEAKER JACK EQUALIZER 4 2222 FOOTSWITCH On Off for Internal Effects TAPE RECORDER XRD 680S Plus external EQ and internal power amp for mains mono Internal EQ and power amp for monitors TO LEFT SPEAKER JACKS TO RIGHT SPEAKER JACKS TAPE RECORDER EQUALIZER Low z AS FOOTSWITCH On Off for Internal Effects IMPORTANT SAFETY INSTRUCTIONS WARNING When using electric products basic cautions should always be followed including the following 1 2 3 4 5 6 10 11 12 13 14 15 16 17 18 Read all safety and operating instructions before using this product All safety and operating instructions should be retained for future reference Obey all cautions in the operating instructions and on2. Intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons Intended to alert the user of the presence of important operating and maintenance servicing instructions in the literature accompanying the product CAUTION Risk of electrical shock DO NOT OPEN CAUTION To reduce the risk of electric shock do not remove cover No user serviceable parts inside Refer servicing to qualified service personnel WARNING To prevent electrical shock or fire hazard do not expose this appliance to rain or moisture Before using this appliance read the operating guide for further warnings Este s mbolo tiene el prop sito de alertar al usuario de la presencia de voltaje peligroso que no tiene aislamiento dentro de la caja del producto que puede tener una magnitud suficiente como para constituir riesgo de corrientazo A Este s mbolo tiene el prop sito de alertar al de la presencia de instruccones importantes sobre la operaci n y mantenimiento en la literatura que viene con el producto PRECAUCION Riesgo de corrientazo No abra PRECAUCION Para disminuir el riesgo de corrientazo no abra la cubierta No hay piezas adentro que el usario pueda reparar Deje todo mantenimiento a los t cnicos calificados ADVERTENCIA Para evitar corrientazos o peligro
3. 150 watts at 8 ohms A 2 ohm operation not recommended Total Harmonic Distortion Less than 0 1 100 mV to Rated Power 20 Hz to 10 kHz 4 ohms typically below 0 05 Compression DDT Cooling Two speed fan cooling Protection Short and open circuit protection High temperature protection Primary fuses Frequency Response 0 0 dB 20 Hz to 20 kHz at rated power into 4 ohms Dynamic Range Greater than 23 dB Maximum THD Below 0 5 for 6 dB overload Below 1 for 16 dB overload Hum amp Noise 83 dB below 300 watts 20 Hz to 20 kHz Power Requirements 120 V AC 1100 watts max Dimensions amp Weight 13 25 Hx 19 W x 12 75 D 51 4 Ibs 2 Due to our efforts for constant improvements features and specifications listed herein are subject to change without notice XRD 680 PLUS LEVEL CHART L amp R POWER AMP 30 CHANNEL INPUT OUTPUT 27 dBV de HEADROOM L amp R 300 W 4 OHMS L amp R MAIN MON MAIN MONITOR TAPE sci TAPE EFFECTS 20 OUTPUTS p dBV MAXIMUM 18 dBV 415 dBV MAXIMUM NOMINAL PR 12 TAPE INPUT LEVEL BOOST 12 dBV CHANNEL INPUT 10 MAX XLR L amp R MAIN AUX INPUT LEVEL 11 dBV MAXIMUM CHANNEL INPUT 6 dBV MON TAPE GRAPHIC MAXIMUM App INPUT LEVEL NOMINAL 1747 CHANNEL CHANNELN EFFECTS OUTPUTS INPUT OUTPUT GRAPHIC d dBV NOMINAL POWER AMP INPUT 0 aBV EQ 0 dB LEVELS 0 dB EQ AUX INPUT LEVEL SENSITIVITY 0 0 FLAT FLAT NOMINAL NO
4. a Keep the PROOF OF PURCHASE In the event warranty service is required during the warranty period you will need this document There will be no identification card issued by Peavey Electronics Corporation 2 IMPORTANCE OF WARRANTY REGISTRATION CARDS AND NOTIFICATION OF CHANGES OF ADDRESSES a Completion and mailing of WARRANTY REGISTRATION CARDS Should notification become necessary for any condition that may require correction the REGISTRATION CARD will help ensure that you are contacted and properly notified b Notice of address changes If you move from the address shown on the WARRANTY REGISTRATION CARD you should notify Peavey of the change of address so as to facilitate your receipt of any bulletins or other forms of notification which may become necessary in connection with any condition that may require dissemination of information or correction 3 You may contact Peavey directly by telephoning 601 483 5365 Commercial Audio Equipment 25E9 LISTED m Features and specifications subject to change without notice Peavey Electronics Corporation 711 A Street Meridian MS 39301 U S A 601 483 5365 Fax 486 1278 01995 80302401 Printed in U S A 10 95
5. MAIN OUTPUT 31 Under normal conditions this signal is also internally patched through the graphic EQ and power amplifier so that this control sets the volume of the speakers connected to the EXTERNAL SPEAKER JACKS 36 Maximum master signal level is obtained by rotating this control fully clockwise Minimum master signal level is obtained by rotating this control fully counterclockwise MASTER MONITOR 21 Controls the overall monitor mix level Maximum monitor signal level is obtained by rotating this control fully clock wise Minimum monitor signal level is obtained by rotating this control fully counterclockwise EFFECTS MASTER 22 Controls the effects level supplied to the internal reverb and the effects out jack Maximum effects signal level is obtained by rotating this control fully clockwise Minimum effects signal level is obtained by rotating this control fully counterclockwise MASTER OUTPUT INPUT TAPE AUX IN LEVEL 23 When external signals are patched into the TAPE IN JACKS 17 or the AUXILIARY INPUTS 25 TAPE AUX IN LEVEL provides control over the level of signals sent from these inputs to the main left and right mixes Maximum TAPE AUX to main mix signal level is obtained by rotating this control fully clockwise Minimum TAPE AUX to main mix signal level is obtained by rotating this control fully counterclockwise NOTE It is possible to use both the AUX and TAPE inputs simultaneously It is however unlikely that the
6. THE EXISTENCE OF THE EXPRESSED LIMITED WARRANTIES AS HEREINABOVE STATED HAVE BEEN COMPLIED WITH IMPLIED WARRANTIES ARE NOT DISCLAIMED DURING THE APPLICABLE ONE YEAR OR NINETY DAY PERIOD FROM DATE OF PURCHASE OF THIS PRODUCT SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THESE LIMITED WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE THESE LIMITED WARRANTIES ARE THE ONLY EXPRESSED WARRANTIES ON THIS PRODUCT AND NO OTHER STATEMENT REPRESENTATION WARRANTY OR AGREEMENT BY ANY PERSON SHALL BE VALID OR BINDING UPON PEAVEY In the event of any modification or disclaimer of expressed or implied warranties or any limitation of remedies contained herein conflicts with applicable law then such modification disclaimer or limitation as the case may be shall be deemed to be modified to the extent necessary to comply with such law Your remedies for breach of these warranties are limited to those remedies provided herein and Peavey Electronics Corporation gives this limited warranty only with respect to equipment purchased in the United States of America INSTRUCTIONS WARRANTY REGISTRATION CARD 1 Mail the completed WARRANTY REGISTRATION CARD to PEAVEY ELECTRONICS CORPORATION POST OFFICE BOX 2898 MERIDIAN MISSISSIPPI 39302 2898
7. here interrupts the normal signal path from the main bus into the equalizer OPERATION NOTE This jack permits the equalizer to be switched away from its normal input and accept an external signal to be equalized If a stereo signal is to be equalized the left signal should be connected to the tip and the right signal should be connected to the ring of a stereo 1 4 plug If a mono 1 4 plug is used signal will only go to the left graphic The right graphic will get no signal EFFECTS OUTPUT 29 This 1 4 jack provides a signal from the EFFECTS mix for external effects or signal processing equipment MONITOR OUTPUT 30 This 1 4 jack provides a signal from the MONITOR for an external monitor amplifier speaker system The level 15 determined by the channel monitor and master monitor controls MAIN OUTPUT 31 These 1 4 jacks provide a stereo signal from the main system mix before the graphic equalizer Used primarily to feed an auxiliary amplifier speaker system See wiring diagram PHANTOM POWER ON OFF 32 This switch selects phantom power on or off for all channels Phantom power is on when the switch is in the down position and off when the switch is in the up position Back Panel POWER 120 VAC 60 Hz FUSE 100 WATTS FIZA 25 OF FIRE OR E EQUIPMENT 4 Zi R E yi TDESSOVOLTS 1 A PRODUCT OF PEAVEY ELECTRONICS CORP MERIDIAN MS MADE IN U S A BUILT UNDER U S PATENT NO 4 318 053 S PLU
8. rotating this control fully clockwise Minimum channel monitor mix level is obtained by rotating this control fully counterclockwise LOW EQ 6 Controls the channel low EQ level An active tone control shelving type 15 dB that varies the low frequency range Maximum low EQ boost is obtained by rotating this control fully clockwise Maximum low EQ cut is obtained by rotating this control fully counterclockwise ront Panel EE ed AE B MID EQ 7 Controls the channel mid EQ level An active tone control peak notch 15 dB that adjusts the mid frequency range Maximum mid EQ boost is obtained by rotating this control fully clockwise Maximum mid EQ cut is obtained by rotating this control fully counterclockwise HIGH EQ 8 Controls the channel high EQ level An active tone control shelving type 15 dB that varies the high frequency range Maximum high EQ boost is obtained by rotating this control fully clockwise Maximum high EQ cut is obtained by rotating this control fully counterclockwise EFFECTS SEND 9 Controls the channel effects drive level Maximum effects signal is obtained by rotating the control fully clockwise Minimum signal level is obtained by rotating this control fully counterclockwise MASTER EFFECTS SELECTOR 10 Rotating the EFFECTS SELECTOR control determines which particular digital effect is drawn from whic
9. the back of the unit All operating instructions should be followed This product should not be used near water i e a bathtub sink swimming pool wet basement etc This product should be located so that its position does not interfere with its proper ventilation It should not be placed flat against a wall or placed in a built in enclosure that will impede the flow of cooling air This product should not be placed near a source of heat such as a stove radiator or another heat producing amplifier Connect only to a power supply of the type marked on the unit adjacent to the power supply cord Never break off the ground pin on the power supply cord For more information on grounding write for our free booklet Shock Hazard and Grounding Power supply cords should always be handled carefully Never walk or place equipment on power supply cords Periodically check cords for cuts or signs of stress especially at the plug and the point where the cord exits the unit The power supply cord should be unplugged when the unit is to be unused for long periods of time If this product is to be mounted in an equipment rack rear support should be provided Metal parts can be cleaned with a damp rag The vinyl covering used on some units can be cleaned with a damp rag or an ammonia based household cleaner if necessary Disconnect unit from power supply before cleaning Care should be taken so that objects do not fall and liquids are not spilled in
10. this limited warranty is extended only to the original retail purchaser and is subject to the conditions exclusions and limitations hereinafter set forth PEAVEY 90 DAY LIMITED WARRANTY ON TUBES AND METERS If this product contains tubes or meters Peavey warrants the tubes or meters contained in the product to be free from defects in material and workmanship for a period of ninety 90 days from date of purchase PROVIDED however that this limited warranty is extended only to the original retail purchaser and is also subject to the conditions exclusions and limitations hereinafter set forth CONDITIONS EXCLUSIONS AND LIMITATIONS OF LIMITED WARRANTIES These limited warranties shall be void and of no effect if a The first purchase of the product is for the purpose of resale or b The original retail purchase is not made from an AUTHORIZED PEAVEY DEALER or c The product has been damaged by accident or unreasonable use neglect improper service or maintenance or other causes not arising out of defects in material or workmanship or d The serial number affixed to the product is altered defaced or removed In the event of a defect in material and or workmanship covered by this limited warranty Peavey will In the case of tubes or meters replace the defective component without charge b In other covered cases i e cases involving anything other than covers footswitches patchcords tubes or meters repair the defect in materia
11. 16 These two jacks provide left and right main outputs to the left and right inputs of a stereo tape deck Output level is determined by the TAPE OUT STEREO LEVEL control 14 TAPE IN JACKS 17 These two jacks provide an input for stereo tape decks CD players etc TAPE OUT TAPE IN CAUTION Before placing connected tape decks in the record mode set the TAPE AUX IN level control to 0 or off Most tape decks feed the input signal directly to the output when in record mode This creates a closed loop condition from the tape out to tape in jack which can affect the operational level or sonic quality of the system PILOT LIGHT LED 18 Illuminates when AC power is being supplied to the amp STEREO 9 BAND GRAPHIC EQ 19 Provides 12 dB equalization at each center frequency EQ boost is obtained by moving a particular EQ band s slide control above the center line EQ cut is obtained by moving a particular EQ band s slide control below the center line OPERATION NOTE This equalizer is designed to provide room equalization feedback control and system tone control No amount of equalization will correct the response curve of a poor loudspeaker Always begin with all sliders in the 0 position and avoid excessively cutting boosting large segments of the audio passband which would limit the system s dynamic range MASTER GAIN 20 Controls the overall volume level of the main system The signal from this control is available at the
12. MINAL FLAT 0 dBV NOMINAL JBV NOMINAL dBV 50 HZ amp 10 TAPE INPUT LEVEL 10 10 dBV MINIMUM AUX INPUT LEVEL CHANNEL INPUT 12 12 dBV 15 dBV MINIMUM NOMINAL XLR 15 dBV CUT 20 GAIN 20 dBV UT CHANNEL INPUT MINIMUM 1 4 30 20 CHANNEL INPUT MINIMUM XLR 40 GAIN 40 dBV 50 60 70 XRD 6805 PLUS BLOCK DIAGRAM Phantom P e ABVDC CHANNEL 1 8 3 BAND EQ MAIN BUS MIC Low Hi EFX BUS MON BUS PA 1 IN Hu AUX TAPE TO MON MON BUS AUX TAPE IN AUX IN y TAPE IN MAIN BUS ps MAIN 9 BAND GRAPHIC EQUALIZER K 125 250 500Hz 1kHz 2kHz 4kHz 8kHz 16kHz TAPE MON MON BUS A gt t H MON OUT EFX EFX BUS gt E H EEN OUT TAPE OUT 16 BIT MUTLI EFFECTS PROCESSOR PA 1 OUT OW 4 OHMS OW 8 OHMS 4 OHMS MINIMUM LOAD 2 A gt poem A E POWER AMP 1 38 00W 4 OHMS 50W 8 OHMS 4 OHMS MINIMUM LOAD OO H EFX FS EFX RETURN MAIN BUS EFX RETURN TO MON MON BUS MAIN PA XRD 680S Plus internal EQ and power amp for mains External EQ and power amp for monitors TAPE RECORDER XRD 680S Plus internal EQ and external power amps for mains External EQs and internal power amp for monitors Pra IN FOOTSWITCH On Off for Internal Effects MONITORS cnn NEN
13. MS Max 19 dBV 9 V RMS Output Level Nom OdBV 1 0 V RMS Max 19 dBV 9 V RMS Input Impedance 10 k ohms Output Impedance 100 ohms MASTER Gain Main 20 dB Monitor 15 dB Tape 15 dB Effects 15 dB Maximum Output Level Main 18 dBV 8 0 V RMS Monitor 18 dBV 8 0 V RMS Tape 18 dBV 8 0 V RMS Effects 18 dBV 8 0 V RMS Nominal Headroom Main 18 dB Monitor 18 dB Tape 18 dB Effects 18 dB Output Impedance Main 100 ohms Monitor 100 ohms Tape 10 k ohms Effects 100 ohms Output Noise Residual 101 dBV Master level down Bus 94 dBV Master nominal all channel levels full CCW Effects Returns down Nominal 86 dBV all controls nominal Low Z input terminated 150 ohms Aux Input Impedance 120 k ohms Aux Input Level Nom OdBV Max 7 Min 15 Input Level Nom 4dBV Max 11 Min 10dBV DIGITAL EFFECTS PROCESSOR Reverberation Settings 32 reverb positions 1 bypass setting 13 warm reverbs 13 bright reverbs 2 gated reverbs 2 reverse reverbs Frequency Response 20 Hz to 11 kHz Quantization 16 Bit Linear PCM Signal To Noise Ratio 95 dB Minimum Headroom 6 dB at Limit LED Illumination POWER AMP Input Sensitivity 1 0 volts for rated output Output Power 34 6 V RMS CH at 120 V AC line 1 kHz input signal Single Amplifier 300 watts at 4 ohms 150 watts at 8 ohms Both Amplifiers 300 watts at 4 ohms
14. S SPEAKER JACKS PARALLELED SPEAKER JACKS PARALLELED 300W 4 OHMS MIN LOAD 300W 4 OHMS MIN LOAD 34 6V RMS 34 6V RMS BACK PANEL FEATURES POWER SWITCH 33 Used to turn AC mains power on or off FUSE 34 WARNING THE FUSE SHOULD ONLY BE REPLACED WHEN THE POWER CORD HAS BEEN DISCONNECTED FROM ITS POWER SOURCE CAUTION USING A FUSE LARGER THAN THE RECOMMENDED SIZE COULD RESULT IN PERMANENT DAMAGE TO THE AMPLIFIER The fuse is located within the cap of the fuseholder If the fuse should fail IT MUST BE REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT AND TO PREVENT VOIDING THE WARRANTY If the unit repeatedly blows fuses it should be taken to a qualified service center for repair LINE CORD 35 120 V products only For your safety we have incorporated a three wire line mains cable with proper grounding facilities It is not advis able to remove the ground pin under any circumstances If it is necessary to use the equipment without proper ground ing facilities suitable grounding adaptors should be used Less noise and greatly reduced shock hazard exists when the unit is operated with the proper grounded receptacles EXTERNAL SPEAKER JACKS 36 Provided for connection of external speaker cabinet Minimum total impedance is 4 ohms for each amplifier LINE MAINS CORD RETAINERS 37 Allow storage of mains cable for travel NOTE The line cord should be removed from the cord retainers before
15. de incendio no deje expuesto a la lluvia o humedad este aparato Antes de usar este aparato lea m s advertencias en la gu a de operaci n Ce symbole est utilis pur indiquer l utilisateur la pr sence l int rieur de ce produit de tension non isol e dangereuse pouvant tre d intensit suffisante pour constituer un risque de choc lectrique Ce symbole est utilis pour indiquer l utilisateur qu il ou qu elle trouvera d importantes instructions sur l utilisation et l entretien service de l appareil dans la litt rature accompagnant le produit ATTENTION Risques de choc lectrique NE PAS OUVRIR ATTENTION Afin de r duire le risque de choc lectrique ne pas enlever le couvercle ne se trouve l int rieur aucune pi ce pouvant tre r par e par l utilisateur Confier l entretien un personnel qualifi AVERTISSEMENT Afin de pr venir les risques de d charge lectrique ou de feu n exposez pas cet appareil la pluie ou l humidit Avant d utiliser cet appareil lisez les avertissements suppl mentaires situ s dans le guide Dieses Symbol soll den Anwender vor unisolierten gefahrlichen Spannungen innerhalb des Geh uses warnen die von Ausreichender Starke sind um einen elektrischen Schlag verursachen zu k nnen Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen die Handhabung und Wartung des Produkts betreffen VORSICHT Risiko El
16. ektrischer Schlag Nicht ffnen VORSICHT Um das Risiko eines elektrischen Schlages zu vermeiden nicht die Abdeckung enfernen Es befinden sich keine Teile darin die vom Anwender repariert werden k nnten Reparaturen nur von qualifiziertem Fachpersonal durchf hren lassen ACHTUNG Um einen elektrischen Schlag oder Feuergefahr zu vermeiden sollte dieses Ger t nicht dem Regen oder Feuchtigkeit ausgesetzt werden Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen ENGLISH Thank you for purchasing the Peavey 6805 Plus mixer which features built in stereo digital effects and 300 watt stereo amplifiers giving a total output power of 600 watts This is a powerful easy to use portable eight channel mixing console Each channel features front panel output and monitor level controls as well as high mid and low equalization and effects emphasis controls Every input channel has a studio quality low impedance XLR type input microphone input as well as a 1 4 line input Switchable 48 V phantom power is provided Your XRD 6805 Plus features a rugged heavy gauge cold rolled steel and aluminum chassis finished in oven cured epoxy for toughness and screen printed utilizing the latest photographic film and U V cured ink technol ogy for razor sharp hard wearing control I D and calibration graphics Every on board component has been carefully chosen to deliver the highest possible performance All printed ci
17. gain matching of the AUX and TAPE will allow this hookup to be useful This practice is not recommended POWER AMP INPUTS 24 These 1 4 jacks provide access to connect external line level signals to the left and right power amplifiers OPERATION NOTE These jacks permit the two internal power amplifiers to be switched away from their normal inputs and to accept external line level signals AUXILIARY INPUTS 25 These 1 4 jacks provide inputs to the left and right main mixing buses and the monitor mixing bus for patching returns from external effects devices extra mixing channels etc If the auxiliary signal is mono plug a mono 1 4 plug into the L MONO jack If the auxiliary signal is stereo plug the left signal into L MONO jack and the right signal into the R jack EFFECTS FOOTSWITCH 26 This 1 4 jack provides access for connection of a footswitch optional and is used to activate defeat digital effects GRAPHIC EQ OUT 27 This 1 4 jack provides access to the output of the internal graphic equalizer This is a TRS Tip Ring Sleeve switch ing jack A stereo 1 4 plug inserted here will have the left signal on the tip and the right signal on the ring Do not use a mono plug on this output unless a mono plug is also plugged into the GRAPHIC EQ INPUT 28 GRAPHIC EQ INPUT 28 This 1 4 jack provides an input to the internal graphic equalizer power amp This is a TRS tip ring sleeve switching jack and a signal inserted
18. gh sound pressure levels it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation SAVE THESE INSTRUCTIONS THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA ALL EXPORTED PRODUCTS ARE SUBJECT TO WARRANTY AND SERVICES TO BE SPECIFIED AND PROVIDED BY THE AUTHORIZED DISTRIBUTOR FOR EACH COUNTRY Ces clauses de garantie ne sont vaiables qu aux Etats Unis et au Canada Dans tour les autres pays les clauses de garantie et de maintenance sont fixees par le distributeur national et assuree par lul seion la legislation envigueur Diese Garantie ist nur in den USA and Kanada Alle Export Produkte sind der Garantie und dem Service des Importeurs des jewelligen Landes unterworfen Esta garantia es valida solamente cuando el producto es comprado en E U continentales o en Canada Todos los productos que sean comprados en el extranjero estan sujetos a las garantias y servicio que cada distribuidor autorizado determine y ofrezca en los diferentes paises PEAVEY ONE YEAR LIMITED WARRANTY REMEDY PEAVEY ELECTRONICS CORPORATION PEAVEY warrants this product EXCEPT for covers footswitches patchcords tubes and meters to be free from defects in material and workmanship for a period of one 1 year from date of purchase PROVIDED however that
19. hever bank has been selected by means of the TIME SELECTOR switch TIME SELECTOR 11 Rotating the TIME SELECTOR control determines which particular digital time is selected for use As will be seen from the front panel illustration digital effect times are available from small room reverbs through extra large rooms gated reverbs delays echoes and multi effects NOTE Refer to the chart printed on the faceplate and select one of the 128 effects using the TIME and SELECT switches There are 16 effects settings for each TIME Use the TIME switch to choose the type of effect and the SELECT switch to choose which variation of this effect to use EFFECTS TO MONITOR 12 Controls the level of the EFFECTS in the monitor system Maximum monitor effects signal level is obtained by rotating this control fully clockwise Minimum monitor effects signal level is obtained by rotating this control fully counterclockwise EFFECTS RETURN 13 Controls the level of the EFFECTS in the main system mix Maximum effects return signal level is obtained by rotating the control fully clockwise Minimum effects return signal level is obtained by rotating this control fully counterclock wise TAPE STEREO LEVEL 1 17 Controls the signal level at the TAPE OKT JACKS 76 Operation is independent of the main MASTER level control 20 and the GRAPHIC EQUALIZER 19 TAPE AUX TO MON 15 Allows the TAPE AUX to be assigned to the monitor TAPE OUT JACKS
20. l or workmanship or replace the product at Peavey s option and provided however that in any case all costs of shipping if necessary are paid by you the purchaser THE WARRANTY REGISTRATION CARD SHOULD BE ACCURATELY COMPLETED AND MAILED TO AND RECEIVED BY PEAVEY WITHIN FOURTEEN 14 DAYS FROM THE DATE OF YOUR PURCHASE In order to obtain service under these warranties you must a Bring the defective item to any PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER and present therewith the ORIGINAL PROOF OF PURCHASE supplied to you by the AUTHORIZED PEAVEY DEALER in connection with your purchase from him of this product If the DEALER or SERVICE CENTER is unable to provide the necessary warranty service you will be directed to the nearest other PEAVEY AUTHORIZED DEALER or AUTHORIZED PEAVEY SERVICE CENTER which can provide such service OR b Ship the defective item prepaid to PEAVEY ELECTRONICS CORPORATION International Service Center 326 Hwy 11 amp 80 East MERIDIAN MS 39301 including therewith a complete detailed description of the problem together with a legible copy of the original PROOF OF PURCHASE and a complete return address Upon Peavey s receipt of these items If the defect is remedial under these limited warranties and the other terms and conditions expressed herein have been complied with Peavey will provide the necessary warranty service to repair or replace the product and will return it FREIGHT COLLECT to y
21. ou the purchaser 5 liability to the purchaser for damages from any cause whatsoever and regardless of the form of action including negligence is limited to the actual damages up to the greater of 500 00 or an amount equal to the purchase price of the product that caused the damage or that is the subject of or is directly related to the cause of action Such purchase price will be that in effect for the specific product when the cause of action arose This limitation of liability will not apply to claims for personal injury or damage to real property or tangible personal property allegedly caused by Peavey s negligence Peavey does not assume liability for personal injury or property damage arising out of or caused by a non Peavey alteration or attachment nor does Peavey assume any responsibility for damage to interconnected non Peavey equipment that may result from the normal functioning and maintenance of the Peavey equipment UNDER NO CIRCUMSTANCES WILL PEAVEY BE LIABLE FOR ANY LOST PROFITS LOST SAVINGS ANY INCIDENTAL DAMAGES OR ANY CONSE QUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THESE LIMITED WARRANTIES ARE IN LIEU OF ANY AND ALL WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE PROVIDED HOWEVER THAT IF THE OTHER TERMS AND CONDITIONS NECESSARY TO
22. rcuit boards are constructed from rugged U S military spec material using the latest automated assembly technology wave solder and computer controlled all faults analyzed and corrected Q A procedures Precision professional reliability and minimal operating noise characteristics are only among the initial criteria used during the process of selecting the components that ensure that your XRD 680S Plus becomes an indis pensable addition to your live performance equipment FRONT PANEL FEATURES BALANCED LOW IMPEDANCE INPUT 1 For use with low impedance microphones or low level sources equipped with an XLR connector LINE INPUT JACK 2 For use with line level signal or compatible high Z microphones equipped with a 1 4 phone plug NOTE It is possible to use both the mic and line inputs on a single channel simultaneously It is however unlikely that the gain matching of the mic and line will allow this hookup to be useful This practice is not recommended LEVEL 3 Controls the channel output level Maximum output level is obtained by rotating this control fully clockwise Minimum output level is obtained by rotating this control fully counterclockwise PAN 4 Provides an individual channel pan L to R facility Center position delivers equal L amp R stereo image balance MONITOR 5 Controls the channel monitor mix level This is independent of all other channel controls Maximum channel monitor mix level is obtained by
23. to the unit through the ventilation holes or any other openings This unit should be checked by a qualified service technician if a The power supply cord or plug has been damaged b Anything has fallen or been spilled into the unit c The unit does not operate correctly d The unit has been dropped or the enclosure damaged The user should not attempt to service this equipment All service work should be done by a qualified service technician This product should be used only with a cart or stand that is recommended by Peavey Electronics Exposure to extremely high noise levels may cause a permanent hearing loss Individuals vary considerably in susceptibility to noise induced hearing loss but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time The U S Government s Occupational Safety and Health Administration OSHA has specified the following permissible noise level exposures Duration Per Day In Hours Sound Level dBA Slow Response 8 90 6 92 4 95 3 97 2 100 1 1 2 102 1 105 1 2 110 1 4 or less 115 According to OSHA any exposure in excess of the above permissible limits could result in some hearing loss Ear plugs or protectors in the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss if exposure is in excess of the limits as set forth above To ensure against potentially dangerous exposure to hi
24. use SPECIFICATIONS NOTE All specifications are typical unless otherwise noted OdBV I volt RMS OdBu 0 778 volts RMS All specifications are referenced to nominal output level 0 dBV unless otherwise noted All measurements are wide band 20 Hz to 20 kHz unless otherwise stated All control settings are nominal 5096 rotation unless otherwise noted CHANNEL Equivalent Input Noise 114 5 dBV at 40 dB max gain Frequency Response to speaker outputs 1 dB 10 Hz to 23 kHz Distortion 1 kHz Less than 0 015 Input Impedance Low ZBal Line Input High EQ 15 dB at 10 kHz minimum Center detent flat 2 dB Mid EQ 15 dB at 600 Hz minimum Center detent flat 2 dB Low EQ 15 dB at 50 Hz minimum Center detent flat 2 dB Nominal Channel Gain Low Z 20dB Line OdB Minimum Channel Gain Low Z 69dB Line 89dB Maximum Channel Gain Low Z 40dB Line 20dB Nominal Input Level Low Z 20dBV Line OdBV Minimum Input Level Low Z 40dBV Line 20dBV 1 7 k ohms 13 k ohms Maximum Input Level Low Z 6dB Line 26dB Phantom Power 48 V DC GRAPHIC EQUALIZER Filter Bandwidth 1 octave Filter Frequencies ISO Stds 63 Hz 125 Hz 250 Hz 1 kHz 2 kHz 4 kHz 8 kHz 16 kHz Filter Q 1 57 Maximum Boost amp Cut 12 dB Noise 102 dBV Distortion 1 kHz Less than 0 005 Frequency Response 1 dB 7 Hz to 40 kHz Input Level Nom OdBV 1 0 V R
Download Pdf Manuals
Related Search