Brady Label Maker Worldwide Identification Solutions User's Manual
Contents
1. arm to ensure it is held straight Hex wrench O ring and spool included Thread the liner under the guide rod between the hold down brush and the strip plate then back under the strip plate Lay the liner across the slot in the take up hub Slide the lock rod into the slot to secure the liner Align shaft collar on guide rod with edge of liner to keep material feeding straight Reel Holder Arm Hold Down Brush Guide Rod Reel Hanger Bar Lock Rod tade Ee Strip Plate IG Ge Take up Hub ADJUSTMENTS Hold Down Brush Using the upper thumbscrew on the side of the machine adjust the hold down brush for tensioning For best results labels should be pressed firmly against the strip plate If labels are held too tightly they will cause excessive drag on the motor Photosensor The photosensor can be adjusted in any direction to accommodate virtually any label Loosening the lower thumbscrew allows the photosensor to swivel and sets the overhang distance of the label over the strip plate When the label is being fed the correct distance tighten the lower thumbscrew Loosen the two screws on the front of the sensor holder to align the photosensor with the center of the label If there are two or more labels across align the photosensor with the last label to be removed When these two screws are tightened the machine is set Positioning of Photosensor Incorrect Baite EO GO e O Sensor sees beyon2. 17 1 NV50015A NV50011A NV50002A NV5001 1 NV5001 1 2 NV50011 1 NV50007 NV50003 NV50009 NV50007 1 NV50021 115V NV50021A 220V NV50005 1 NV50021 1 NV50019 NV50019F NV50018C NV50005 3 Date purchased copy of invoice or packing slip required SPECIFICATIONS Liner Capacity 25 to 4 5 Width 6 35mm to 115mm Label 125 to 7 Length 3 2mm to 178mm Roll Capacity 12 30 5mm Feed Speed 1 3 sec 3 3mm sec Dimensions Inches 10 8 L x 10 8 W x 14 5 H Centimeters 27 4 L x 27 4 W x 36 8 H wa ezteia Electrical 117V 50 60Hz lt 1 amp Requirements 220V 50 60Hz available NV50005 1 at startup NV50021 1
3. BRADY O bd Brady Worldwide Identification Solutions 6555 West Good Hope Road P O Box 2131 Milwaukee WI 53201 2131 Phone 800 537 8791 Fax 800 292 2289 www bradyid com 05 01 DSP 5 EGONEN A EXPLODED VIEW Read this user s manual before use to ensure proper operation Keep the manual on hand for reference in case there is a problem F P E A 3 82 2 E T be D F5 E O erdie Warranty Information a 2 Sg E eS d Bee 5 g2 8 9r ZER amp Side ae Feat res eai 3 835 82 SEE Sate SGS Ee m3 Of EE Ze n reg 5 Boe Koa Ge OS us ISS J FSS 2 ours uu z z Notes 3 Ts Za Hz SES 5 blk Zz NEE Sa brrrrrrrrrrrerrrrrrrrrrreerrerrrrrrrrrrreera Za LS Ea zee T Se x lt 3 Repair Poli 3 ws gE Ze Zea Bi 5 EPI FOUCY 2 cece e cece e eee ee eee eens lt oS ZEA ERE cst ifi dS D 2 Specifications rae ataiko 3 AF 9 O38 DEUS iets ee eee ada EARE 4 eda FE o Q SUS Operation Adjustments rra 5 sg gge Q a O lt x F w Maintenance rrura 6 a f k b g z HEE a AiR ee EEE 6 Gee be z oL lt F be Exploded View a 7 Za E E So o GO Ogos E T o Es E 2 z 826 d Q S58 2 3 S 3 i WARRANTY POLICY FOR DSP SERIES LABEL DISPENSERS 2 2 5 O a a ae 2 Brady Corporation warrants all parts on DSP series label dispensers against defects 3 E in design materials and workmanship for a period of 180 days Labor to replace oc we 2 GO defective parts will be perfo
4. d label Will not stop Sensor sees strip plate Will not feed Correct eea Sensor sees front edge of label Turn machine off when not in use Remove liner material from take up hub at approximately 3 in diameter or if motor appears to be straining Do not operate machine without covers in place Do not operate if inspection reveals a damaged power or sensor cord Will dispense butt cut and die cut material Adjustable photosensor for pinpoint accuracy Handled lock rod makes scrap removal easy No tools required for adjustment LEGEND ltem Part e Keep strip plate free of adhesive build up Nv50008 e Clean photosensor with compressed air or dry cloth NV50008 1 e Do not drop the dispenser or subject it to heavy shock NV50008 2 e Turn off machine when not in use NV50010 NV50010 1 NV50010 2 REPAIR POLICY NV50017 B NV50017 1 Contact BRADY CORPORATION to determine nature of problem NV50017 2 l l tate l NV SPOOL Furnish Brady with the Sed information NV50001A 115V 1 Who the unit was purchased from NV50001C 220V 2 Model number and serial number NV50001 1 NV50018 2 dee GO Brady will issue an RGA Return Goods Authorization for repair NV50012 1 Return machine to Brady by UPS insured and prepaid NV50014 1 Brady will notify the customer if there is a repair charge NV50014 3 NV50014 NV50017 1 NV50026B NV5001 1 2 NV50026 1 NV50026A NV50015 NV500
5. rmed at no charge for the first 90 days after date of ZE BO E purchase Warranty does not cover transportation costs Ws a m Za O lt nN E at f TE TE Q Our sole obligation under this warranty is limited to repair replacement or credit of Eba E g lt the itzei price at our option for the machines listed above which do not SE d g perform properly the function for which they were designed a ZE eg DU Gi lS 23 wags Warranty repair is contingent upon our examination and determination that alleged et S as aaa N N defects have not been caused by misuse abuse improper installation or application repair alteration accident or neglect in use storage transportation or handling The above warranty and remedy constitutes Brady Corporation s sole liability hereunder and are in lieu and exclusive of all other warranties and remedies expressed implied or statutory including but not limited to those of merchantability and fitness for a particular purpose 2A Arm Main Plate screw 1ea 2 REEL HOLDER ARM 2B Hex wrench 23A Switch Base screw 2ea 22 POWER CORD 23 SAFETY SWITCH 23B Nut 2ea 1 COVER 1A Cover Base screw 4ea 1B Cover Main Plate screw 2ea SET UP INSTRUCTIONS Using 5 32 4mm hex wrench adjust reel holder arm to vertical Place the label roll on the 1 25mm reel hanger bar If roll has 3 76 2mm core use plastic spool Slide O ring onto reel hanger bar to hold roll against reel holder
Download Pdf Manuals
Related Search