Barco MDCC-6230
Contents
1. 40 Indications for use The Coronis Fusion 6MP MDCC 6230 display is a display device capable of displaying two 3MP display images electronically fused together on the one panel Itis intended to be used in displaying and viewing digital images for review and analysis by trained medical practitioners It provides a screen resolution of 3280 x 2048 pixels at a pixel pitch of 0 1995mm This provides the equivalent resolution of 2 x 3MP displays The Coronis Fusion 6MP MDCC 6230 display is not intended for primary diagnosis of Mammography images Caution USA Federal law restricts this device to sale by or on the order of a physician or a practitioner trained on its use K5902055 CORONIS FUSION 6MP 17 01 2014 8 Important information FCC class B This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference re ceived including interference that may cause undesired operation This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This device generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to2. Display IMO msasa Mn 31 5 28 Display stals enoaan REEDE EL T 31 6 Cleaning your display us ees ese ESE ns Kk NS NE Ee ee Dee EG US ee We ee De ee seen one 33 6 1 Cleaning instructions 2 Let REDES ED AR EE GEE ES EE DR GE BEDE DE SG EG eg eg EE RE E PAR Hide 33 K5902055 CORONIS FUSION 6MP 17 01 2014 1 Table of contents 7 Repackaging instructions iss RR RR RR RR RR RR RR RR RR RR RR RR nennen nnn nnn nnn nnn 35 7 1 Repacking your display e se semen ess nnn 36 8 Important information EE EES Ee ED EE SR ER DE EE EE ER Ee eee eden cee es 37 8 1 Safety informatON EE ee EE EE EE SERE eee RR EE Ran ee enna AA mr a ere ER EER EER Re dd ee be EE Re 37 8 2 Environmental information kk ke ee ee EE Ek ER RR Re ee ee ee ehem mese 38 8 3 Regulatory compliance information nnn 40 8 4 EMC NOCE ER EE OE be 41 8 5 Explanation of symbols semen e meses 44 8 6 Legal disclaimer 2 2 oce BERE ell a eee DE eek dd PRA ER RR vaal ge vedi aa ed de ne See du 46 8 7 Technical specifications EE EE cece EE EE EE Re ER eee eee eee eee teen tenet eee tees s n n nnn 47 8 8 Open source license information 00 00 cece cece cece cece cece EE GE cent ee ee ee ee ee nnn 48 K5902055 CORONIS FUSION 6MP 17 01 2014 7 Welcome 1
3. Indicates Direct Current DC Indicates Alternating Current AC Stand by ad 8 6 Legal disclaimer 46 Disclaimer notice Although every attempt has been made to achieve technical accuracy in this document we assume no responsibility for errors that may be found Our goal is to provide you with the most accurate and usable documentation possible if you discover errors please let us know Barco software products are the property of Barco They are distributed under copyright by Barco N V or Barco Inc for use only under the specific terms of a software license agreement between Barco N V or Barco Inc and the licensee No other use duplication or disclosure of a Barco software product in any form is authorized The specifications of Barco products are subject to change without notice Trademarks All trademarks and registered trademarks are property of their respective owners Copyright notice This document is copyrighted All rights are reserved Neither this document nor any part of it may be reproduced or copied in any form or by any means graphical electronic or mechanical including photocopying taping or information storage and retrieval systems without written permission of Barco 2013 Barco N V All rights reserved Patent information This product is covered under the following intellectual property rights US Patent RE43 707 US Patent 7 038 186 US Patent 7 166 829 US Patent 6 950 09
4. User Interface gt Menu menu 3 Enter the Position submenu 4 Select one of the available OSD menu positions and confirm 5 2 OSD menu language About the OSD menu language By default the OSD menu comes up in English However there s a wide range of other languages avail able for the OSD menu of your Coronis Fusion 6MP To change the language of the OSD menu 1 Bring up the OSD main menu 2 Navigate to the Configuration gt User Interface gt Menu menu 3 Enter the Language submenu 4 Select one of the available languages and confirm 5 3 OSD menu automatic close function About the OSD menu automatic close function By default the OSD menu will disappear automatically after approximately 90 seconds of inactivity How ever this function can be disabled so that the OSD menu remains on the screen until manually closed To enable disable the OSD menu automatic close function 1 Bring up the OSD main menu 2 Navigate to the Configuration gt User Interface gt Menu menu 3 Enter the Automatic Close submenu 4 Select Enabled Disabled as desired and confirm K5902055 CORONIS FUSION 6MP 17 01 2014 SSCS 19 5 Advanced operation 5 4 Power status indicator light About the power status indicator light By default when the display is switched on the power status indicator light is dimmed This behavior can be changed so that the power status indicator light will be blue when the display is swi
5. cupboard Installation Place the device on a flat solid and stable surface that can support the weight of at least 3 devices If you use an unstable cart or stand the device may fall causing serious injury to a child or adult and serious damage to the device This apparatus conforms to CE0120 MDD 93 42 EEC A1 2007 47 EC class llb product CE 2004 108 EC IEC 60950 1 2005 A1 2009 2ND EDITION IEC 60601 1 2005 ANSI AAMI ES 60601 1 2005 C1 2009 A2 2010 CAN CSA C22 2 No 60601 1 2008 DEMKO EN 60601 1 2006 EN 60601 1 2 2007 CCC GB9254 2008 GB4943 1 2011 GB17625 1 2012 KCC VCCI FCC class B ICES 001 Level B FDA 510 k RoHS National Scandinavian Deviations for CL 1 7 2 Finland Laite on liitettava suojamaadoituskoskettimilla varustettuun pistorasiaan Norway Apparatet m tilkoples jordet stikkontakt Sweden Apparaten skall anslutas till jordat uttag 8 2 Environmental information 38 Disposal Information Waste Electrical and Electronic Equipment A mamma This symbol on the product indicates that under the European Directive 2012 19 EU governing waste from electrical and electronic equipment this product must not be disposed of with other municipal waste Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment To prevent possible harm to the environment or K5902055 CORONIS FUSION 6MP 17
6. ee K5902055 CORONIS FUSION 6MP 17 01 2014 5 Advanced operation To manually select a video input signal 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Sources gt Left Right Image Source menu 3 Enter the Input Signal submenu 4 Select one of the available input signals and confirm 5 24 Video encoding modes x Your Coronis Fusion 6MP display automatically detects the connected video input sig nals and applies the correct video encoding settings Manually selecting a video encod ing mode is possible but then your display s image source selection mode should be set to allow this Please refer to Image source selection modes page 28 to do this About video encoding modes Video encoding modes specify how the color and luminance information is encoded in the video signal In consumer displays this is usually done by a limited 8 bit encoding mechanism Your Coronis Fusion 6MP however features 10 bit encoding enabling it to better match the DICOM defined grayscale range Such an extensive range is necessary to comply with the guidelines set forward by the latest medical guidelines The available video encoding modes for your display are listed below Please note that the display controller connected to your display might not always sup port all these video encoding modes Standard This mode uses the standard 8 bit encoding mechanism HDR1 This mode features 10 bit video encoding followi
7. Fr 88 Heatsinks Ha ER EVE Power Supply Unit PER Paper Manuals K5902055 CORONIS FUSION 6MP 17 01 2014 39 8 Important information SARA 424 ET E E Component name Hazardous substances and elements Ed E AB ZRKA SR Pb Hg Cd Cr6 PBB Bi PBDE CD manual O amp m CB SA EDS EAN PIU HR HA PAS SE SIT 11363 2006 AN NEMRERKRUT O Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ T11363 2006 X Sn UB mCB ELS SPEAKER 3E 15 or HA PRYS SMM SJ T 11363 2006 trem EH Res X Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ T11363 2006 EHAK HHR E MAN TE RT i EIP M 27 588 E h E Ri 8 48 RI 85 ie SUE TA EGO RE Wh LIMA E FR ABR EFUP R Barco dn Pr AMIEFUPA SE SERB TUER A SAK EA FAI 3E RAT EA 9 ES d ER AEF PR GB HE All Electronic Information Products EIP that are sold within Chinese Mainland must comply with the Electronic Information Products Pollution Control Labeling Standard of Chinese Mainland marked with the Environmental Friendly Use Period EFUP logo The number inside the EFUP logo that Barco uses please refer to the photo is based on the Standard of Electronic Information Products Environmental Friendly Use Period of Chinese Mainland 8 8 3 Regulatory compliance information
8. Navigate to the Status menu 3 Enter the Display Image Sources Calibration or Connectivity submenu as desired K5902055 CORONIS FUSION 6MP 17 01 2014 SSCS 31 5 Advanced operation 32 K5902055 CORONIS FUSION 6MP 17 01 2014 6 Cleaning your display 6 CLEANING YOUR DISPLAY 6 1 Cleaning instructions To clean the display Clean the display using a sponge cleaning cloth or soft tissue lightly moistened with a recognized clean ing product for medical equipment Read and follow all label instructions on the cleaning product In case of doubt about a certain cleaning product use plain water Do not use following products Alcohol solvents at higher concentration gt 5 e Strong alkalis lye strong solvents Acid e Detergents with fluoride e Detergents with ammonia e Detergents with abrasives e Steel wool Sponge with abrasives Steel blades e Cloth with steel thread CAUTION Take care not to damage or scratch the front glass or LCD Be careful with rings or other jewelry and do not apply excessive pressure on the front glass or LCD CAUTION Do not apply or spray liquid directly to the display as excess liquid may cause damage to internal electronics Instead apply the liquid to a cleaning cloth K5902055 CORONIS FUSION 6MP 17 01 2014 33 6 Cleaning your display 34 K5902055 CORONIS FUSION 6MP 17 01 2014 7 Repackaging instructions 7 REPACKAGING INSTRUCTION
9. WELCOME 1 4 About the product Overview Thank you for choosing this Coronis Fusion 6MP Coronis Fusion 6MP is an ingenious PACS display system designed to further enhance flexibility and productivity in diagnostic imaging Featuring the industry s first 30 inch color LCD that can be used as two seamless heads or one wide screen display Coronis Fusion 6MP offers you the freedom to organize your workspace just the way you want it It allows you to read CT MR cath and echo cardiogram images or any other combination side by side on a single diagnostic screen Coronis Fusion 6MP features the latest breakthrough In Plane Switching IPSPro LCD technology This technology brings the most advanced LCD viewing characteristics on the market setting new standards for brightness and contrast even from a wide viewing angle Use the instructions in this guide to install your Coronis Fusion 6MP display and discover all these interesting features yourself CAUTION Read all the important safety information before installing and operating your Coronis Fusion 6MP Please refer to the dedicated chapter in this user guide 1 2 What s in the box Overview Your Coronis Fusion 6MP comes with this Coronis Fusion 6MP user guide a system CD e two DVI cables two DisplayPort cables e a USB cable aset of AC power cords an external power supply If you ordered a Barco display controller it s also in the box together with its acce
10. generated on the display controller is converted to grayscale in your display The available grayscale conversion modes are No Conversion 70000000 Use Red Channel This mode is intended for grayscale displays where gray is sent over the red channel Use Green Channel This mode is intended for grayscale displays where gray is sent over the green channel I mode is intended for grayscale displays where gray is sent over the blue channel Use All Channels This mode is intended for grayscale displays where gray is sent over the red green and blue channel This is done by means of a standard conversion mechanism where 30 red 59 green and 11 blue are used to generate gray To manually select a grayscale conversion mode 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Sources gt Left Right Image Source menu 3 Enter the Grayscale Conversion submenu 4 Select one of the available color conversion modes and confirm 5 26 EDID timings 30 Your Coronis Fusion 6MP display automatically detects the connected video input sig nals and applies the correct timings Manually configuring the EDID timings is possible but then your display s image source selection mode should be set to allow this Please refer to Image source selection modes page 28 to do this About EDID timings Following EDID timings are available for your Coronis Fusion 6MP Resolution Allows to manually modify the r
11. installed your display and display controller the Windows start up messages will appear once the boot procedure is finished x Your Coronis Fusion 6MP display will be running in a basic video mode at a default re fresh rate when first time starting up If you are using a Barco display controller please consult the dedicated user guide available on the system CD to install the drivers soft ware and documentation When this is done your display will automatically detect the connected video input signal s and apply the correct video mode and refresh rate K5902055 CORONIS FUSION 6MP 17 01 2014 4 Daily operation 4 DAILY OPERATION 4 1 Recommendations for daily operation Optimize the lifetime of your display Enabling the Display Power Management System DPMS of your display will optimize its diagnostic life time by automatically switching off the backlight when the display is not used for a specified period of time By default DPMS is enabled on your display but it also needs to be activated on your workstation To do this go to Power Options Properties in the Control Panel Barco recommends setting DPMS activation after 20 minutes of non usage Ge Use a screen saver to avoid image retention Prolonged operation of an LCD with the same content on the same screen area may result in a form of image retention You can avoid or significantly reduce the occurrence of this phenomenon by using a screen saver Yo
12. physically installed in your computer If you are using a Barco display controller please consult the user guide delivered with it to do this 3 1 Removing the covers The connector compartment cover should be removed to get access to the connectors To remove the connector compartment cover 1 Gently lift the clips at one of the handles of the connector compartment cover to release that side of the cover 2 Do the same at the other side of the cover 3 Remove the cover The display stand cover should be removed to get access to the cable routing channel To remove the display stand cover 1 Gently press and hold the clips at the inside top of the cover K5902055 CORONIS FUSION 6MP 17 01 2014 7 3 Display installation 3 2 Unlocking the height mechanism s In the factory the height positioning system in the display stand is locked with a red hook to prevent damage during transportation You ll have to remove this hook before adjusting your display height position To remove the hook 1 Position the display with its rear side facing you 2 While holding the display panel pushed down pull out the red hook in the display stand 8 K5902055 CORONIS FUSION 6MP 17 01 2014 3 Display installation 3 Keep the clip in the dedicated hole in case the display needs to be shipped later To retain the hook for possible future transportation insert the short red
13. pixel to one or more adjacent pixels so that the size of the displayed image will be a multiple ofthe original image source video input signal X Image scaling is only possible when the resolution of your display s video input signal is less than or equal to half the maximum resolution of the display To enable disable image scaling 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Source menu 3 Enter the Scaling submenu 4 Select Enabled Disabled as desired and confirm K5902055 CORONIS FUSION 6MP 17 01 2014 SSF 27 5 Advanced operation 5 22 Image source selection modes About image source selection modes Your Coronis Fusion 6MP automatically detects the number of video input signals connected attaches them to the correct display side and applies the correct video settings to it resolution video encoding mode refresh rate However it may be needed to manually select the video input signal s to be displayed on a certain display side or to adjust certain video settings yourself The start to this is selecting one of the following image source selection modes available for your display Automatic In this mode your display automatically detects the connected video input signals attaches them to the correct display side and applies the correct video settings to it resolution video encoding mode refresh rate No video settings are available when this mode is selected One Image S
14. radio communications However there is no guarantee that interference will not occur in a particular installation If this device does cause harmful interference to radio or television reception which can be determined by turning the device off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the device and receiver e Connect the device into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Canadian notice This ISM device complies with Canadian ICES 001 Cet appareil ISM est conforme la norme NMB 001 du Canada 8 4 EMC notice General information No specific requirement on the use of external cables or other accessories except power supply With the installation of the device use only the delivered power supply or a spare part provided by the legal manufacturer Using another can result in a decrease of the immunity level of the device Electromagnetic emissions The Coronis Fusion 6MP is intended for use in the electromagnetic environment specified below The customer or the user of the Coronis Fusion 6MP should assure that it is used in such an env
15. room Therefore itis also important to select a realistic reading room when enabling ALC This can be done by following the instruc tions in Reading rooms page 26 To enable disable ALC 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Ambient Light menu 3 Enter the Ambient Light Compensation submenu 4 Select Enabled Disabled as desired and confirm 5 19 Reading rooms 26 About reading rooms Reading rooms can only be selected when the DICOM display function is selected Therefore please refer to Display functions page 25 to correctly set the display function The American Association of Physicists in Medicine AAPM composed a list of pre defined reading rooms Each of these reading rooms are defined by following parameters the maximum light allowed in this type of room e the preset ambient light correction value for this reading room These parameters are stored in your display and determine the preset ambient light correction value to take into account to recalculate the DICOM display function when Ambient Light Compensation ALC is enabled Please refer to Ambient Light Compensation ALC page 26 to enable ALC The available reading rooms for your Coronis Fusion 6MP are CR DR MAMMO Corresponds to light conditions in diagnostic reading rooms for computed radiology digital radiology or mammography This setting has the lowest maximum ambient light CT MR NM Co
16. the Configuration gt Power Management menu 3 Enter the Hibernate Timeout submenu 4 Set the timeout value as desired and confirm 5 12 Luminance target About the luminance target The luminance target of your Coronis Fusion 6MP is adjustable over a predefined range When you change the luminance target the display will adjust its backlight to reach the target To set the luminance target 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration menu 3 Enter the Luminance Target submenu 4 Set a luminance target value as desired and confirm The default value is 450 cd m The five year warranty is valid for this setting 5 13 Color presets About color presets The available color preset settings for your display are Clearbase Simulation of the clearbase film color temperature Bluebase Simulation of the bluebase film color temperature User When selecting the User color temperature setting you will be able to manually define the X and Y coordinates or the display color temperature in separate submenus Native White The native unmodified color temperature of the LCD panel To select a color preset 1 Bring up the OSD main menu 2 Navigate to the Configuration Calibration Color Settings menu K5902055 CORONIS FUSION 6MP 17 01 2014 23 5 Advanced operation 3 Enter the Color Presets submenu 4 Select one of the available Color Preset
17. 0 cable 10 OO K5902055 CORONIS FUSION 6MP 17 01 2014 3 Display installation 3 5 Connecting the power cable To connect the power cable to the display 1 Connect the supplied external DC power supply to the 24 VDC power input of your Coronis Fusion 6MP display 2 Plug the other end of the external DC power supply into a grounded power outlet by means of the proper power cord delivered in the packaging 3 6 Routing the cables To route the cables 1 Route all connected cables through the cable routing channel in the stand of your display Tip The cable straps at the inside of the connector compartment allow you to fix the cables for better shielding of the cables 3 7 Re attaching the covers To re attach the display stand cover 1 Slide the display stand cover downward You ll hear a click sound of the cover s clips when the display stand cover is in position K5902055 CORONIS FUSION 6MP 17 01 2014 11 3 Display installation Pay attention that all cables stay in the cable channel while re attaching the cover To re attach the connector compartment cover 1 Slide the cover s top in position and then push the cover s bottom You ll hear a click sound of the cover s clips when the connector compartment cover is in position 38 VESA mount installation WARNING Use an arm that is approved by VESA according to the VESA 100 mm stan dar
18. 01 2014 8 Important information human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources For more information about recycling of this product please contact your local city office or your municipal waste disposal service For details please visit the Barco website at http www barco com en AboutBarco weee Turkey RoHS compliance A mmmm T rkiye Cumhuriyeti AEEE Y netmeli ine Uygundur Republic of Turkey In conformity with the WEEE Regulation HE Xi RoHS Chinese Mainland RoHS see pt aa rii NCE Hag ru P ut ES LAK BAT AU T Barco ih rh RI AE AS MA SKA TE WR AIS HAS Ss HEA RHS HES a A E DBs AP Ml BMCVE JE GEERF BO SOROS ER m According to the China Administration on Control of Pollution Caused by Electronic Information Products Also called RoHS of Chinese Mainland the table below lists the names and contents of toxic and or hazardous substances that Barco s product may contain The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China in the section Limit Requirements of toxic substances in Electronic Information Products SAMA 5 FA ABASMWARITH Component name Hazardous substances and elements E Ik m ADB ies E AR Pb Hg Cd Cr6 ME Printed Circuit Assemblies T oe HR mR LCD panel at He eb Be i Plastic enclosure EA
19. 55 CORONIS FUSION 6MP 17 01 2014 5 Advanced operation 5 7 Keys sound About keys sound By default the keys will make a beep sound on every touch However this sound can be disabled so that no sound will be heard when using the keys To enable disable the keys sound 1 Bring up the OSD main menu 2 Navigate to the Configuration gt User Interface gt Controls menu 3 Enter the Sound submenu 4 Select Enabled Disabled as desired and confirm 5 8 Ethernet over USB About Eth over USB By default the Ethernet over USB will be disabled This does not disable the USB hub and still allows to make use of the display s USB downstream connectors and any external devices connected to it key board mouse Please note that a connection from a PC USB downstream connector to the display s USB upstream connector is required to be able to use this functionality By enabling the Ethernet over USB you allow the internal Coronis Fusion 6MP processor to communicate directly over USB with the connected PC Enabling the Ethernet over USB is only recommended when you are using a non Barco display controller If you are using a Barco display controller this communication will automatically be done over the connected video cable s To enable disable the eth over USB 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Connectivity menu 3 Enter the Eth over USB submenu 4 Select Enabled Disa
20. 8 European Patent 1 274 066 European Patent 1 915 875 K5902055 CORONIS FUSION 6MP 17 01 2014 8 Important information 8 7 Technical specifications Overview Product acronym MDCC 6230 Screen technology TFT AM Color LCD Dual Domain IPS Pro Active screen size diagonal 772 mm 30 4 Active screen size H x V 654 x 409 mm 25 8 x 16 1 Aspect ratio H V Resolution native 6MP 3280 x 2048 configurable to 2 x 3MP 1640 X 2048 Pier pi Color support Uniform Luminance Yes Technology ULT Per Pixel Uniformity PPU Yes Backlight Output Stabilization Yes 2x BLOS Gud Yes Maximum luminance 720 cd m DICOM calibrated luminance 500 cd m ULT off Contrast ratio typical 1000 1 panel typical Response time Tr Tf 18 ms canning frequency H V 30 150 kHz 15 80 Hz Housing color Blek Siver DVI D Dual Link 2x DisplayPort 2x NA 1 upstream endpoint 3 downstream 2 0 Power requirements nominal 100 240V Power consumption nominal 125W ower save mode Yes ower management DVI DMPM DP DMPM 280 MHz OSD languages English German French Dutch Spanish Italian Portugese Polish Russian Swedish Chinese simplified Japanese Korean Arabic x H Portrait NA Landscape 731 x 580 676 x 265 mm x H Portrait NA Landscape 731 x 485 x 141 mm x H 869 x 764 x 400 mm Net weight with stand 26 5 kg Dimensions with stand W x D Dimensions w o stand W x D Dimensions p
21. Coronis Fusion 6MP User Guide MDCC 6230 K5902055 02 BARCO 17 01 2014 Visibly yours Barco nv President Kennedypark 35 8500 Kortrijk Belgium Phone 32 56 23 32 11 Fax 32 56 26 22 62 Support www barco com esupport Visit us at the web www barco com Printed in Belgium Table of contents TABLE OF CONTENTS 1 WGICODIGL uoce deu e RE AENEID nid ot Na FE eA ERI MEL a DL ME RUTRUM DLE E 3 1 4 Ab tthe products 12 ER tdi RAM NERA de Beate E rA AU SOR RE EE ee NE DERE 3 REIS Go MA EO ARE HON te Bia ca at Oe ad Patel daa dada needs tn PODER 3 2 Parts controls and connectors rrveenenvunevenneennneveeneeanneennveeannea 5 2 11 Display front VIeW oio dro eee GE EE Ge Rui AG TRIER dae cance AR DERE ee ER RE 5 2 2 Display reat VIEW REEDE GE GE vaprale CE eoo EDO tee TL EE AE Le Ee PPP uter PUER 6 3 Display installation is SE 7 3 15 Removing the Covers iis skede se Hed ette SEE ES Ee kd ee debetur ebbe tA id Ie beast Hb ebat Mahi des 7 3 2 Unlocking the height mechanism 8 3 3 Adjusting the display positio sssri issaraen a ee ee ee ee ke ER RR Re ee ee ee ee ee ek RR Re ee ee e nn 9 3 4 Connecting the signal cables iii EE EE ee EE EE RE RR EE RR ee RE EE se nn EE RE ee EE ER Re nensis 10 3 5 Connecting the power cable iii EE EE EER EER EE e a eene EE EE nnn hh aka EE EE SEE EER RR ah nn nene 11 3 6 Routinigtlie c
22. D menu Please refer to OSD menu position page 19 for detailed instructions on how to do this S 4 5 Navigating through the OSD menus About OSD menu navigation Navigating through the OSD menu can be done by using the keys or by using the control wheel How to navigate through the OSD menus using the keys 1 Use the Right Down and Left Up keys to move through the sub menus change values or make selec tions 2 To go into a submenu or confirm adjustments and selections use the Menu Enter key 3 Use the Stand by Cancel key to cancel adjustments or exit a sub menu 4 Exit the OSD menu by touching the Stand by Cancel key for approximately 2 seconds How to navigate through the OSD menus using the control wheel 1 Rotate the control wheel to move through the menus change values or make selections 2 To go into a submenu or confirm adjustments and selections shortly click the control wheel 3 Click the control wheel for approximately 2 seconds to cancel adjustments or exit a sub menu 18 LLL K5902055 CORONIS FUSION 6MP 17 01 2014 5 Advanced operation 2 ADVANCED OPERATION 5 1 OSD menu position About the OSD menu position By default the OSD menu comes up in the bottom center position of the screen This position can be modified however There s choice from a number of predefined positions To change the position of the OSD menu 1 Bring up the OSD main menu 2 Navigate to the Configuration gt
23. RIBUTOR BE LIABLE FOR DIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES EVEN IF ADVISED OF THE K5902055 CORONIS FUSION 6MP 17 01 2014 8 Important information POSSIBILITY OF SUCH DAMAGES MORE INFORMATION DETAILS IS TO BE FOUND IN EACH SPE CIFIC OPEN SOURCE LICENSE Copyright on each Open Source Software component belongs to the respective initial copyright holder each additional contributor and or their respective assignee s as may be identified in the respective doc umentation source code README file or otherwise You shall not remove or obscure or otherwise alter the respective copyrights You acknowledge living up to the conditions of each separate Open Source Software license A list of the Open Source Software components used is available in the applicable EULA through the customer section of the Barco website or through other online means K5902055 CORONIS FUSION 6MP 17 01 2014 49
24. S Overview of the packaging Image 7 1 amp Box 5 Coronis Fusion 6MP display 9e System CD User guide Q Top buffer K5902055 CORONIS FUSION 6MP 17 01 2014 35 7 Repackaging instructions 7 1 Bottom buffer Display controller box 4 Power supply o Cables video USB power Repacking your display 36 How to repack your display 1 2 3 4 5 Oo Place the empty box on a stable surface Slide the system CD and user guide in the dedicated bag attached at the inside of the box Place the bottom buffer in the box Put the power supply in the dedicated cavity of the bottom buffer Put the Coronis Fusion 6MP display in its original bag and place it in the box with its panel facing downwards Put the top buffer on top of the display 7 When applicable slide the display controller box in the dedicated cavity of the buffers 8 Put all cables video USB power in their original bag and slide them in the dedicated cavity of the buffers Close and seal the box K5902055 CORONIS FUSION 6MP 17 01 2014 8 Important information 8 IMPORTANT INFORMATION 8 1 Safety information General recommendations Read the safety and operating instructions before operating the device Retain safety and operating instructions for future reference Adhere to all warnings on the device and in the operating instructions manual Follow all instructions for operation and use Electrical Sh
25. ables EES ER EE ag EE ie De ed GEE REEL ULLA EDI Aaa GEE EE RES RS Re Ge DE see 11 3 7 Re attaching the COVOrsS ces iicet eg De oU EE ES Ge bk ED ge GE ke Re EE GEE EES EE A HA DE he 11 3 85 VESA mount installation ssiri rane EE De mda Ge GEE RE ER RED Ee Se Ge RR EE IER GEE SR ee AE BE ie 12 3 9 Firstime Starting Up iie SEER EE be ee ER GR GEE GE ER AP EE a VHC DIR ER NER EA DE Ee 14 A gt Daily Operations EE EE EG GE SO NEE ne arte 15 4 1 Recommendations for daily operation 15 4 2 Key indicator lights si 22202 reir DES Ge EG RD A en MAD tete 16 4 3 Stand by switching iere eee GE ee OE N ra ee ele Du EL DR eed eee ee eles 16 44 Bringing up the OSD menus ie EE ESE EE ER ser EER ER RR htm GE SEE ehh Re ER ER SEER RR Rn rrr UE 17 4 5 Navigating through the OSD menus ee GEE cece enn Ie emen 18 5 Advanced operatlOni ss EER SEDEER DEE RE EG BEE ESE SE US RA SR SE DAD AE RE ESE EUER EE EE EIE Ee 19 5 1 OSD men Position EE Sour uu x SE ee ca Re ER Ra bh Pettitte nt SERRA EE Re tt EE 19 5 2 OSD menu lang age 1 10 41 01 DE EES EE Led uera EE Re PR a a EE ER ES SG dire 19 5 3 OSD menu automatic close function enn 19 5 4 Power status indicator light noresi EE Lin Ee de EG Ee eee OE GEE Ee eale v mit dd se 20 5 5 Key indicator lights srir Aare EE GEE ea ie ee DE er ESE Re pog NEE GEE EE a ee e ee rt 20 5 6 Power lock TunCUOM ie seir
26. ackaged W K5902055 CORONIS FUSION 6MP 17 01 2014 47 8 Important information Net weight w o stand 20 kg stand Swivel Ta Certifications CE0120 MDD 93 42 EEG A1 2007 47 EC class llb product CE 2004 108 EC IEC 60950 1 2005 A1 2009 2ND EDITION IEC 60601 1 2005 ANSI AAMI ES 60601 1 2005 C1 2009 A2 2010 CAN CSA C22 2 No 60601 1 2008 DEMKO EN 60601 1 2006 EN 60601 1 2 2007 CCC GB9254 2008 GB4943 1 2011 GB17625 1 2012 KCC VCCI FCC class B ICES 001 Level B FDA 510 k RoHS Quick Installation Sheet Video cables 2x DVI Dual Link 2x DisplayPort Main cables UK European CEBEC KEMA USA UL CSA adaptor plug NEMA 5 15P Chinese CCC USB 2 0 cable External power supply MediCal QAWeb Eni perat MEE i Operating humidity 8 8096 non condensing EG 15 9596 non condensing NA 8 8 Open source license information 48 Open source license information Open source license usage This product contains software components released under an Open Source license A copy of the source code is available on request by contacting your Barco customer support representative EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONT
27. applications to improve the perception of low Hounsfield values DICOM Digital Imaging and Communications in Medicine is an international standard that was developed to improve the quality and communication of digital images in radiology In short the DICOM display function results in more visible grayscales in the images Barco recommends selecting the DICOM display function for most medical viewing applications This display function will be automatically selected when display functions are defined by MediCal QAWeb Select one of these display functions in case the display is to replace a CRT display with a gamma of 1 8 or 2 2 respectively Dynamic Gamma 2 2 To select a display function 1 Bring up the OSD main menu K5902055 CORONIS FUSION 6MP 17 01 2014 ___ 25 5 Advanced operation 2 Navigate to the Configuration gt Calibration menu 3 Enter the Display Function submenu 4 Select one of the available display functions and confirm 5 18 Ambient Light Compensation ALC About ALC x Ambient Light Compensation ALC can only be enabled on your display when the DI COM display function is selected Therefore please refer to Display functions page 25 to correctly set the display function When ALC is enabled the DICOM display function will be recalculated taking a preset ambient light cor rection value into account This value is determined by the selected reading
28. bled as desired and confirm 5 9 USB About USB By default USB will be enabled This will allow the connected PC to communicate directly over USB with the internal Coronis Fusion 6MP processor By disabling USB communication between the internal Coronis Fusion 6MP processor and the connected PC will not be possible This does not disable the USB hub and still allows to make use of the display s USB downstream connectors and any external devices connected to it Keyboard mouse Please note that a connection from a PC USB downstream connector to the display s USB upstream connector is required to be able to use this functionality K5902055 CORONIS FUSION 6MP 17 01 2014 21 5 Advanced operation x Enabling the USB endpoint is only recommended when you are using a non Barco dis play controller If you are using a Barco display controller this communication will au tomatically be done over the connected video cable s To enable disable USB 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Connectivity menu 3 Enter the USB submenu 4 Select Enabled Disabled as desired and confirm 5 10 DPMS mode About DPMS mode Enabling the Display Power Management System DPMS mode on your display will optimize its diagnos tic lifetime by automatically switching off the backlight when the display is not used for a specified period of time By default DPMS mode is enabled on your display but it also need
29. cator lights as previously described 2 While the keys are light up touch the Stand by Cancel key for approximately 2 seconds As a result the display will switch on and the power status indicator light is dimmed To switch your display on using the control wheel 1 Press the control wheel for approximately 2 seconds As a result the display will switch on and the power status indicator light is dimmed The power LED can be disabled in the OSD menus Please refer to Power status indi cator light page 20 for detailed instructions on how to do this To switch your display to Stand by using the keys 1 Light up the keys indicator lights as previously described 2 While the keys are light up touch the Stand by Cancel key a small window pops up Press the button again to confirm As a result the display will switch to stand by mode and the power status indicator light is orange To switch your display to Stand by using the control wheel 1 Press the control wheel once a small window pops up Press the control wheel again to confirm As a result the display will switch to stand by mode and the power status indicator light is orange x In case of a power outage recovery your display will always start up in the power mode it was in before the power interruption i e stand by or on This protects your display against inadvertent image retention problems 4 4 Bringing up the OSD menus About OSD menu The OSD menu allo
30. ct the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced technician for help Electromagnetic immunity The Coronis Fusion 6MP is intended for use in the electromagnetic environment specified below The customer or the user of the Coronis Fusion 6MP should assure that it is used in such an environment Immunity test IEC 60601 Compliance level Electromagnetic environment guidance Electrostatic discharge 6kV contact 6kV contact Floors should be wood ESD 8kV air 8kV air concrete or ceramic tile IEC 61000 4 2 B E If floors are covered with synthetic material the relative humidity should be at least 3096 Electrical fast 2kV for power supply 2kV for power supply Mains power quality transient burst lines lines should be that of a typical commercial or hospital environment Test levels IEC 61000 4 4 1kV for input output 1kV for input output lines lines Surge 1 KV line s to line s 1 kV line s to line s Mains power quality should be that of a typical commercial or hospital environment Voltage dips short lt 5 Ur 1 gt 95 dip in lt 5 UT gt 95 dip in Mains power quality IEC61000 4 5 2 kV line s to earth 2 kV line s to earth interruptions and voltage Ur for 0 5 cycle Ur for 0 5 cycle should by that of a typical varakens on Power ons Ur 60 dip in Un 40 Us 20 ap in Un emmers eco for 5 cycles f
31. d Use an arm that can support the weight of the display Refer to the technical specifica tions of this display for the applicable weight CAUTION You should mount the panel in landscape position Portrait position is pos sible but not supported Overview The panel standard attached to a stand is compatible with the VESA 100 mm standard Thus it can be used with an arm that is approved by VESA This chapter shows you how to release the panel from the stand and how to attach it to an arm If you re not using an arm you can skip this chapter K5902055 CORONIS FUSION 6MP 17 01 2014 3 Display installation 1 Gently pull open both lower sides of the cover 3 Lift the plastic frame that covers the fixation of the panel to the stand Turn it for 45 degrees to uncover the fixation screws K5902055 CORONIS FUSION 6MP 17 01 2014 or 13 3 Display installation itself Instead make sure that the arm is equipped with a VESA approved handle and FN WARNING Never move a display attached to an arm by pulling or pushing the display use this to move the display Please refer to the instruction manual of the arm for more information and instructions 3 9 First time starting up 14 Overview You are now ready to start up your Coronis Fusion 6MP for the first time 1 Switch on your Coronis Fusion 6MP as described in Stand by switching page 16 2 Turn on the computer connected to your display If you have properly
32. end of the hook back into the stand of your display 3 3 Adjusting the display position Now that the height positioning system of your display is unlocked you can adjust the display position To adjust the display position 1 Tilt swivel raise and lower the display as desired K5902055 CORONIS FUSION 6MP 17 01 2014 _ 9 3 Display installation CAUTION Do not try to pivot your display when attached to the stand Trying to do so could cause serious damage to your display and its stand 3 4 Connecting the signal cables To get access to the connectors remove the connector compartment cover See Re moving the covers page 7 s Each side of your display can have a different video input connected one side can have DVI connected while the other side has DisplayPort connected Both display sides can have the same video input connected as well but only one video input is allowed on each side of your display To connect the signal cables to the display 1 Connect one head of the display controller to the DVI 1 or DisplayPort 1 connector with one of the supplied DVI or DisplayPort cables 2 Connect another head of the display controller to the DVI 2 or DisplayPort 2 connector with one of the supplied DVI or DisplayPort cables 3 If you want to make use of your display s USB downstream connectors connect a PC USB downstream connector to the display s USB upstream connector by means of the supplied USB 2
33. esolution of the image source video input signal Refresh Rate Allows to manually select the refresh rate of the image source video input signal depending on the maximum refresh rate of the display controller connected to your display Color Depth Allows to change the color depth to 8 or to 10 bit K5902055 CORONIS FUSION 6MP 17 01 2014 5 Advanced operation To manually set EDID timings 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Sources gt Left Right Image Source menu 3 Enter the Timings submenu 4 Select Resolution Refresh Rate or Color Depth 5 Select one of the available settings and confirm 5 27 Display info About display info Your display serial number color type native resolution firmware versions etc are available in a dedi cated submenu of the OSD menu To retrieve info about your display 1 Bring up the OSD main menu 2 Navigate to the About this Display menu to make the information visible on the screen 5 28 Display status About display status The Status submenu of the OSD menu provides info on the current status of your display runtimes tem peratures etc the status of the connected image sources video encoding mode timings etc the current calibration status of your display display function luminance ALC etc and the status about activated connections To retrieve the status of your display 1 Bring up the OSD main menu 2
34. for high grade Quality Assurance providing maximum diagnostic confidence and uptime at least This policy includes calibration on regular intervals Connecting to MediCal QAWeb Server offers even more possibilities Learn more and sign up for the free MediCal QAWeb Essential level at www barco com healthcare ga Barco recommends to install MediCal QAWeb Agent and apply the default QAWeb policy Cg 4 2 Key indicator lights To make the keys light up 1 Gently sweep your finger over the bottom right hand side of your display As aresult the keys will light up and are now available for further actions However if no further actions are taken within the following 5 seconds the key indicator lights will dim again The key auto dim function can be disabled in the OSD menus Please refer to Key in dicator lights page 20 for detailed instructions on how to do this 4 3 Stand by switching x The connected power supply also provides a switch that can be used to turn the power completely off To use the display please make sure to switch on this power supply This can be done by pushing the on off switch on the power supply into the position 16 LLL K5902055 CORONIS FUSION 6MP 17 01 2014 4 Daily operation Switching on the display while it is in stand by mode or vice versa can both be done by using the keys or by using the control wheel To switch your display on using the keys 1 Light up the keys indi
35. for using the display for diagnostic purposes Text In this mode the luminance is reduced to approximately half of the luminance This is intended for using the display with office applications such as word processing Please note that text mode is not persistent once powered off the unit will restart in diagnostic mode As the Coronis Fusion 6MP is intended to be used in a diagnostic environment the di agnostic mode should always be selected To select a viewing mode 1 Bring up the OSD main menu 2 Navigate to the Configuration Calibration menu 3 Enter the Viewing Mode submenu 4 Select Diagnostic Text as desired and confirm 5 17 Display functions About display functions Native uncorrected panels will display all grayscale color levels with luminance increments that are not optimal for crucial diagnostic information Studies have shown however that in medical images certain grayscale color parts contain more diagnostic information then others To respond to these conclusions display functions have been defined These functions emphasize on these parts containing crucial diag nostic information by correcting the native panel behavior NN NN you select Native the native panel behavior will not be corrected Dynamic Gamma 1 8 These are gamma functions that are shifted to take into account the non zero luminance of an LCD panel when driven with a black signal They are especially useful in CT
36. g time disconnect it from the AC inlet to avoid damage by transient over voltage To fully disengage the power to the device please disconnect the power cord from the AC inlet K5902055 CORONIS FUSION 6MP 17 01 2014 37 8 Important information Power cords e Utilize a UL listed detachable power cord 3 wire type SJ or equivalent 18 AWG min rated 250 V min provided with a hospital grade type plug 5 15P configuration for 120V application or 6 15P for 240V application Do not overload wall outlets and extension cords as this may result in fire or electric shock Mains lead protection U S Power cord Power cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them paying particular attention to cords at plugs and receptacles The power supply cord should be replaced by the designated operator only at all time Use a power cord that matches the voltage of the power outlet which has been approved and complies with the safety standard of your particular country Water and moisture Never expose the device to rain or moisture Never use the device near water e g near a bathtub washbasin swimming pool kitchen sink laundry tub or in a wet basement Ventilation Do not cover or block any ventilation openings in the cover of the set When installing the device in a cupboard or another closed location heed the necessary space between the set and the sides of the
37. ian RE ey eee SILE Maa EE De ge EE eee t gee 20 AD GEE GIE AR EE 21 5 8 Ethernet over USB ER EES eee WII De ee dans Bad Ge ei 21 5 9 WS Bie EER STRES ED hat A ES SR ee pee eh ie Oe EER 21 5 10 DPMS mode seers RE maa ha Ono PE AED eee iad ED 22 Wu mU 22 5 12 Luminance target iii eee ved xx e Ld ale EE Ee A LPs EE ll 23 5 13 GOON presets PI EL 23 5 14 Color temperature EE eee dde ee Une te RARE DR Ee Ge T Tub t OTRA A ode dd 24 5 15 Color coordinates ESE EE RE add ie ge be ee Ote EE EE GE ge GE EE ee EE EE RR daa Me addet 24 5 16 VIEWING modes citt ESE SR bg EE ie Ge dant etti be ee GR GEE e PELA Mid 24 5 17 Display functioris EER EER EE Ee EE heg GE EE be Ek ge GE EE Ge EE GEE Ee EE He dads 25 5 18 Ambient Light Compensation ALC ee ER Re ee ee ee ek kk ek RR Re ee ee ee ek ke ER RR Re ee ee ee ek n 26 5 19 Reading TOOMS sd EE EE EEE be GE GEE EE EE GE be De ge GE oe REPE mahe 26 5 20 Continuous ALCS RE EE EK N aides 27 SPAM 27 5 22 Image source selection modes 6 66 ccc EE eee EE EE eee senes dne nh s Re ee EE EE nnne nh EE be dee 28 5 23 Video input sigrials EES ESE SEED Ge bebe e EE EE A bu hacienda nahh qe PEE Et ie dades 28 5 24 Video encoding modes ssi en EE EER ete ee deena ent a need eee EER ER ka be de dee 29 5 25 Grayscale conversion modes sss nn 30 9 26 ziBIDRIMI PME T 30 5 2
38. ironment Es EE Electromagnetic environment Guidance RF emissions Group 1 The Coronis Fusion 6MP uses RF energy only for its internal gii function Therefore its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment RF emissions Class B The Coronis Fusion 6MP Harmonic emissions Class D establishments including IEC 61000 3 2 those directly connected to the Voltage fluctuations flicker Complies public low voltage power supply EMISSIONS network that supplies buildings IEC 61000 3 3 used for domestic purposes K5902055 CORONIS FUSION 6MP 17 01 2014 8 Important information This Coronis Fusion 6MP complies with appropriate medical EMC standards on emissions to and inter ference from surrounding equipment Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Interference can be determined by turning the equipment off and on If this equipment does cause harmful interference to or suffer from harmful interference of surrounding equipment the user is encouraged to try to correct the interference by one or more of the following mea sures e Reorient or relocate the receiving antenna or equipment Increase the separation between the equipment and receiver Conne
39. ng the High Dynamic Range HDR standard usually used on color displays HDR2 HDR2 is a Barco specific mode featuring 10 bit video encoding following the High Dynamic Range HDR standard but allowing full refresh rate which is not always possible with HDR1 This mode is usually used on color displays Dual 10 only with Barco display controller Dual 10 is a Barco specific 10 bit video encoding mode which is usually used on grayscale displays and which allows full refresh rate Automatic When selecting this option your Coronis Fusion 6MP will automatically assign the correct video encoding settings to the connected video input signals To manually select a video encoding mode 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Sources gt Left Right Image Source menu 3 Enter the Video Encoding submenu 4 Select one of the available video encoding modes and confirm K5902055 CORONIS FUSION 6MP 17 01 2014 29 5 Advanced operation 5 25 Grayscale conversion modes x Your Coronis Fusion 6MP display automatically detects the connected video input signals and applies the correct grayscale conversion settings Manually selecting a grayscale conversion mode is possible but then your display s image source selection mode should be set to allow this Please refer to Image source selection modes page 28 to do this About grayscale conversion modes Grayscale conversion modes specify how color
40. ock or Fire Hazard To prevent electric shock or fire hazard do not remove cover No serviceable parts inside Refer servicing to qualified personnel Do not expose this apparatus to rain or moisture Type of protection electrical Display with external power supply Class equipment Degree of safety flammable anesthetic mixture Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide Non patient care equipment Equipment primarily for use in a health care facility that is intended for use where contact with a patient is unlikely no applied part The equipment may not be used with life support equipment The user is not supposed to touch SIP SOPs and the patient at the same time Power connection Equipment with external 24 VDC power supply Power requirements The equipment must be powered using the delivered medical approved 24 VDC SELV power supply The medical approved DC power supply must be powered by the AC mains voltage The power supply is specified as a part of the ME equipment or combination is specified as a ME system To avoid the risk of electric shock this equipment must only be connected to a supply mains with protective earth The equipment should be installed near an easily accessible outlet The equipment is intended for continuous operation Transient over voltage If the device is not used for a lon
41. or 5 cycles IEC 61000 4 11 E M of the Coronis Fusion 70 Ur 30 dip in UT 70 Ur 30 dip in Ur 6MP requires continued for 25 cycles for 25 cycles operation during power A opns A ae ee mains interruptions it yr E dip in ua li dip in recommended that T 3 the Coronis Fusion 6MP be powered from an uninterruptible power supply or a battery Power frequency 50 60 Not applicable Power frequency Hz magnetic field magnetic fields should IEC 61000 4 8 be at levels characteristic of a typical location in a typical commercial or hospital environment Conducted RF 3 Vrms 3V Portable and mobile RF communications 1 is the a c mains voltage prior to application of the test level 2 Coronis Fusion 6MP doesn t contain susceptible components to magnetic fields 42 D K5902055 CORONIS FUSION 6MP 17 01 2014 8 Important information Immunity test IEC 60601 Compliance level Electromagnetic environment guidance IEC 61000 4 6 150 kHz to 80 MHz en eer used no closer to any Radiated RF 3 V m part of the Coronis Fusion IEC 61000 4 3 80 MHz to 2 5 GHz SM les delg capias than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter Recommended separation distance d 1 2 P d 1 2 P 80 MHz to 800 MHz d 2 34 P 800 MHz to 2 5 Ghz Where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufac
42. ource This mode is intended for displaying and manually configuring only one connected video input signal When selecting this mode the video settings become available for the selected video input signal Two Image Sources This mode is intended for displaying and manually configuring two connected video input signals one on each display side When selecting this mode the video settings become available for the selected video input signal on each side of the display To select an image source selection mode 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Image Sources menu 3 Enter the Image Source Selection submenu 4 Select one of the available image source selection modes and confirm 5 23 Video input signals 28 x Your Coronis Fusion 6MP display automatically detects the connected video input sig nals Manually selecting image source video input signals is possible but then your display s image source selection mode should be set to allow this Please refer to Im age source selection modes page 28 to do this About input signals The available input signals for your display are DisplayPort 1 The input corresponding to the DisplayPort 1 connector DVI 1 The input corresponding to the DVI 1 connector DisplayPort 2 The input corresponding to the DisplayPort 2 connector DVI 2 The input corresponding to the DVI 2 connector Automatic Selection The input is automatically selected
43. ronis Fusion 6MP is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled The customer of the user of the Coronis Fusion 6MP can help prevent elec tromagnetic interference by maintaining a minimum distance between portable and mobile RF communi cations equipment transmitters and the Coronis Fusion 6MP as recommended below according to the maximum output power of the communications equipment Rated maximum output Separation distance according to frequency of transmitter power of transmitter I50kHz to 80MHz 80MHz to 800MHz 800MHz to 2 5GHz d 2 3 P 0 12 0 23 0 73 2 3 23 At 80 MHz and 800 MHz the separation distance for the higher frequency range applies These guidelines may not apply in all situations Electromagnetic propagation is af fected by absorption and reflection form structures object and people 8 5 Explanation of symbols Symbols on the device On the device or power supply you may find the following symbols nonrestrictive list C Indicates compliance with the Directive 93 42 EEC as Class device C Indicates compliance with the Directive 93 42 EEC as Class II device 0120 FC Indicates compliance with Part 15 ofthe FCC rules Class A or Class B 5 For transmitters rated at a maximum output power not listed above the recommended separation distance d in meters m can be estimated using the eguation applicable to the freguency of
44. rresponds to light conditions in diagnostic rat rooms for computed tomography magnetic resonance or nuclear medicine scans K5902055 CORONIS FUSION 6MP 17 01 2014 5 Advanced operation taff Office Corresponds to light conditions in office rooms Clinical Viewing Room Corresponds to light conditions in diagnostic reading rooms for clinical viewing Emergency Room Corresponds to light conditions in emergency rooms Operating Room Corresponds to light conditions in operating rooms This setting has the highest maximum ambient light To select a reading room 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Ambient Light menu 3 Enter the Reading Room submenu 4 Select one of the available reading rooms and confirm 5 20 Continuous ALC About Continuous ALC x Continuous ALC can only be selected when the DICOM display function is selected Therefore please refer to Display functions page 25 to correctly set the display func tion Enabling continuous ALC will continuously recalculate the DICOM display function taking the averaged ambient light into account To select continuous ALG 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Ambient Light menu 3 Enter the Continuous ALC submenu 4 Select Enabled Disabled as desired and confirm 5 21 Image scaling About image scaling Enabling image scaling will multiply each individual
45. s and confirm 5 14 Color temperature About color temperature It is possible to change the color temperature of your display Color temperature can only be changed on your display when color presets is set to user Therefore please refer to Color presets page 23 to do this To change the color temperature 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Color Settings menu 3 Enter the Color Definition submenu 4 Select Color Temperature and confirm 5 Enter the Color Temperature submenu 6 Set the Temperature value as desired and confirm 5 15 Color coordinates About color coordinates It is possible to change the color coordinates of your display Color coordinates can only be changed on your display when color presets is set to user Therefore please refer to Color presets page 23 to do this To change the color coordinates 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Calibration gt Color Settings menu 3 Enter the Color Definition submenu 4 Select Color Coordinates and confirm 5 Enter the X and or Y submenu 6 Set the coordinate value for X and or Y as desired and confirm 5 16 Viewing modes About viewing modes The Coronis Fusion 6MP can be used in two viewing modes 24 _ K5902055 CORONIS FUSION 6MP 17 01 2014 5 Advanced operation Diagnostic This mode provides the full calibrated luminance and is intended
46. s to be activated on your workstation To do this go to the Power options properties window of your workstation Barco recommends setting DPMS activation after 20 minutes of non usage Cg When DPMS mode is enabled on your display an additional OSD power saving function becomes available hibernate Please refer to Hibernate page 22 for more information on hibernation and how to enable this function To enable disable DPMS mode on your display 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Power Management menu 3 Enter the DPMS Mode submenu 4 Select Enabled Disabled as desired and confirm 5 11 Hibernate 22 About hibernate Enabling hibernation will not only switch off the backlight but will also force the display to disable other functionalities so that power consumption is further reduced to a minimum This happens after a specific period of time which can be manually adjusted Hibernate can only be enabled on your display when the DPMS mode is enabled first Therefore please refer to DPMS mode page 22 to do this K5902055 CORONIS FUSION 6MP 17 01 2014 5 Advanced operation To enable disable hibernation on your display 1 Bring up the OSD main menu 2 Navigate to the Configuration gt Power Management menu 3 Enter the Hibernate submenu 4 Select Enabled Disabled as desired and confirm To specify the hibernate timeout 1 Bring up the OSD main menu 2 Navigate to
47. ssories A dedicated user guide is available on the system CD Keep your original packaging It is designed for this display and is the ideal protection during transport and storage K5902055 CORONIS FUSION 6MP 17 01 2014 _ 3 7 Welcome 4 2 K5902055 CORONIS FUSION 6MP 17 01 2014 2 Parts controls and connectors 2 PARTS CONTROLS AND CONNECTORS 2 1 Display front view Overview TO 008000 9 Image 2 1 Front view USB downstream connectors Q Left Up key Q Right Down key Q Menu Enter key Q Stand by Cancel key Power status indicator light Control wheel Q Ambient light sensor K5902055 CORONIS FUSION 6MP 17 01 2074 5 2 Parts controls and connectors 2 2 Display rear view Overview 08 O 000000 OOO Image 2 2 Rear view 24 VDC power input DVI 2 video input 5 VDC 0 5 A power output DisplayPort 2 video input Connector compartment cover Neck cover DisplayPort 1 video input Display stand cover DV 1 video input USB upstream connector Ethernet connector see note below 6600060 USB downstream connector The Ethernet connection is used for maintenance purposes and is not supported for user application 6 K5902055 CORONIS FUSION 6MP 17 01 2014 3 Display installation 3 DISPLAY INSTALLATION Prior to installing your Coronis Fusion 6MP and connecting all necessary cables make sure to have a suitable display controller
48. tched on When the display is in stand by mode the power status indicator light will always turn orange even when the power status indicator light is disabled To enable disable the power status indicator light 1 Bring up the OSD main menu 2 Navigate to the Configuration gt User Interface gt Indicator Lights menu 3 Enter the Power Status submenu 4 Select Enabled Disabled as desired and confirm 5 5 Key indicator lights About the key indicator lights By default after lighting up the key indicator lights will dim again if no further actions are taken within the following 5 seconds However this behavior can be changed so that the key indicator lights are always on or always off To configure the key indicator lights 1 Bring up the OSD main menu 2 Navigate to the Configuration gt User Interface gt Indicator Lights menu 3 Enter the Keys submenu 4 Select Automatic Always On Always Off as desired and confirm 5 6 Power lock function 20 About the power lock function By enabling the power lock function the Coronis Fusion 6MP is forced to remain switched on This means that it can t be switched to stand by mode until the power lock function is disabled again To enable disable the power lock function 1 Bring up the OSD main menu 2 Navigate to the Configuration User Interface Controls menu 3 Enter the Power Lock submenu 4 Select Enabled Disabled as desired and confirm K59020
49. the transmitter Where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer 44 JJ FK5902055 CORONIS FUSION 6MP 17 01 2014 8 Important information oil Indicates the device is approved according to the UL regulations il Indicates the device is approved according to the UL regulations for Canada and US e 5 Indicates the device is approved according to the UL Demko regulations Indicates the device is approved according to the CCC regulations Indicates the device is approved according to the VCCI regulations Indicates the device is approved according to the KC regulations Indicates the device is approved according to the BSMI regulations Indicates the USB connectors on the device Indicates the DisplayPort connectors on the device Indicates the manufacturing date ig4O0 580Od Indicates the temperature limitations for the device to safely operate within specs x x lt a Indicates the device serial no Warning dangerous voltage Caution Consult the operating instructions BE E Eg 6 Values for xx and yy can be found in the technical specifications paragraph K5902055 CORONIS FUSION 6MP 17 01 2014 45 8 Important information Indicates this device must not be thrown in the trash but must be recycled according to the European WEEE Waste Electrical and Electronic Equipment directive TE
50. turer and d is the recommended separation distance in meters m Test levels Field strengths from fixed RF transmitters as determined by an electromagnetic site survey 3 should be less than the compliance level in each frequency range 4 Interference may occur in the vicinity of equipment marked with symbol Cp At 80 MHz and 800 MHz the higher frequency range applies 3 Field strengths from fixed transmitters such as base stations for radio cellular cordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the measured field strength in the location in which the Coronis Fusion 6MP is used exceeds the applicable RF compliance level above the Coronis Fusion 6MP should be observed to verify normal operation i abnormal performance is observed additional measures may be necessary such as re orienting or relocating the Coronis Fusion 6M 4 Over the frequency range 150 kHz to 80 Mti field strengths should be less than 3 V m K5902055 CORONIS FUSION 6MP 17 01 2014 43 8 Important information s These guidelines may not apply in all situations Electromagnetic propagation is af fected by absorption and reflection from structures objects and people Recommended separation distance The Co
51. u can activate a screen saver in the Display properties window of your workstation Barco recommends setting screen saver activation after 5 minutes of non usage A good screen saver displays moving content In case you are working with the same image or an application with static image elements for several hours continuously so that the screen saver is not activated change the image content regularly to avoid image retention of the static elements Understand pixel technology LCD displays use technology based on pixels As a normal tolerance in the manufacturing of the LCD a limited number of these pixels may remain either dark or permanently lit without affecting the diagnostic performance of the product To ensure optimal product quality Barco applies strict selection criteria for its LCD panels To learn more about LCD technology and missing pixels consult the dedicated white papers available at www barco com healthcare Enhance user comfort Every Barco multi head display system is color matched with the highest specifications in the market tant to use all displays of a multi head configuration at the same rate to preserve color Barco recommends keeping color matched displays together Furthermore it is impor Ge matching throughout the economic lifetime of the system K5902055 CORONIS FUSION 6MP 17 01 2014 15 4 Daily operation Maximize quality assurance The MediCal QAWeb system offers online service
52. ws you to configure different settings to make your Coronis Fusion 6MP display fit your needs within your working environment Also you can retrieve general information about your display and its current configuration settings through the OSD menu Bringing up the OSD menus can be done by using the keys or by using the control wheel How to bring up the OSD menus using the keys 1 If not already done so switch on the display as previously described 2 Light up the keys indicator lights as previously described 3 While the keys light up touch the Menu Enter key As a result the OSD main menu comes up in the bottom right corner of the screen If no further actions are taken within the following 90 seconds however the OSD menu will disappear again K5902055 CORONIS FUSION 6MP 17 01 2014 __ 17 4 Daily operation How to bring up the OSD menus using the control wheel 1 If not already done so switch on the display as previously described 2 Shortly turn the control wheel As a result the OSD main menu comes up in the bottom right corner of the screen If no further actions are taken within the following 90 seconds however the OSD menu will disappear again DI The OSD menu auto exit function can be disabled in the OSD menu Please refer to OSD menu automatic close function page 19 for detailed instructions on how to do this 9 The OSD menu position can be modified in the OS
Download Pdf Manuals
Related Search