PAR56 10MM UV LED PAR user manual
Contents
1. OFF Cross references References to other locations in this manual are identified by an arrow and the specified page number In the electronic version of the manual you can click the cross reference to jump to the specified location Example See Cross references on page 7 PARS6 10MM UV th mann MUSIC IS OUR PASSION General notes 1 3 Symbols and signal words In this section you will find an overview of the meaning of symbols and signal words that are used in this manual Signal word Meaning DANGER This combination of symbol and signal word indicates an immediate dangerous situation that will result in death or serious injury if it is not avoided WARNING This combination of symbol and signal word indicates a pos sible dangerous situation that can result in death or serious injury if it is not avoided NOTICE This combination of symbol and signal word indicates a pos sible dangerous situation that can result in material and environmental damage if it is not avoided th mann LED PAR MUSIC IS OUR PASSION General notes Warning signs Type of danger Warning high voltage Warning suspended load Warning danger zone gt ee PAR56 10MM UV th mann MUSIC IS OUR PASSION Safety instructions 2 Safety instructions Intended use This device is intended to be used as an electronic illumination effect using LED technics Use the device only as described in this user manual An2. Press one of the arrow keys repeatedly until the display shows SET Press OK Press one of the arrow keys repeatedly until the display shows SPEER Press OK Now you can set the programme speed for the preprogrammed automatic shows Use the arrow keys to select a value between 1 and 255 the display shows 7001 7255 This setting is only relevant if the device is not controlled via DMX When the display shows the desired value press OK to confirm the selection Then press M to return to the higher menu level To return to the higher menu level without changes press M Press M Press one of the arrow keys repeatedly until the display shows SET Press OK Press one of the arrow keys repeatedly until the display shows STRO Press OK Now you can set the strobe effect speed Use the arrow keys to select a value between 0 and 24 the display shows S 00 S 24 This setting is only relevant if the device is not controlled via DMX When the display shows the desired value press OK to confirm the selection Then press M to return to the higher menu level To return to the higher menu level without changes press M LED PAR 28 Dimmer setting Operation Press M Press one of the arrow keys repeatedly until the display shows SET Press OK Press one of the arrow keys repeatedly until the display shows DIMM Press OK Now you can adjust the dimmer Use the arrow k
3. TER LAE PAR56 10MM UV LED PAR themann MUSIC IS OUR PASSION user manual Musikhaus Thomann e K Treppendorf 30 96138 Burgebrach Germany Telephone 49 0 9546 9223 0 E mail info thomann de Internet www thomann de 02 12 2014 ID 276112 V2 Table of contents na vu RK WUN Table of contents General notes nina mn lidiitsnneteceeretaminnrie te fersti s 5 1 1 Further information 1 2 Notational conventions 7 1 3 Symbols and signal Words rennes 8 Safety instructions sminseiunnisnnnedin suiiiijnessjjvdvendsdsdnridtiviejarsmsendeveder 10 Features un inerte etes tetes insiste 14 Installation RE EE ssshacearsoeicstaacesceseneusat opedesvacrase donna Diet 15 Starting gt asese aen ea aeaa sa oE Ee EEEa Easa SNE E ENEAN a aeai 19 Connections and controls EEE EN E O ETON 22 Operation 7 1 Starting up the device inner 72 Malin Men s kaaria aa a e LEa EE ER AR AR T 7 3 Menu overview 7 4 Functions in 2 channel DMX mode Technical specifications 32 PAR56 10MM UV th mann MUSIC IS OUR PASSION Table of contents themann MUSIC IS OUR PASSION 10 11 12 Plug and connection assignments 33 Troublesho0ting et nd an 34 Cleaning s r 36 Protecting the environment 37 LED PAR 1 General notes General notes This manual contains important instructions for
4. the 4 preprogrammed automatic shows Use the arrow keys to select a value between 1 and 4 the display shows P 01 P 04 The automatic show can only be activated on the device that operates as Master This setting is only relevant if the device is not controlled via DMX The device can operate in stand alone mode or control connected devices of the same type that have to be configured as Slaves When the display shows the desired value press OK to confirm the selection Then press M to return to the higher menu level To return to the higher menu level without changes press M Operating mode Slave Press M Press one of the arrow keys repeatedly until the display shows LINE Press OK Press one of the arrow keys repeatedly until the display shows SL Press OK Now you can assign a number to the device by which it is addressed as slave by the master Use the arrow keys to select a value between 1 and 512 the display shows A007 A512 This setting is only relevant if the device is operated as slave by a master but is not controlled via DMX When the display shows the desired value press OK to confirm the selection Then press M to return to the higher menu level To return to the higher menu level without changes press M PAR56 10MM UV th mann MUSIC IS OUR PASSION 27 Operation Programme speed Strobe effect speed themann MUSIC IS OUR PASSION Press M
5. the safe operation of the unit Read and follow the safety instructions and all other instructions Keep the manual for future reference Make sure that it is available to all those using the device If you sell the unit please make sure that the buyer also receives this manual Our products are subject to a process of continuous development Thus they are subject to change PAR56 10MM UV th mann MUSIC IS OUR PASSION General notes 1 1 Further information On our website www thomann de you will find lots of further information and details on the following points Download This manual is also available as PDF file for you to download Use the search function in the electronic version to find the topics of Keyword search interest for you quickly Our online guides provide detailed information on technical basics Online guides and terms Personal consultation For personal consultation please contact our technical hotline If you have any problems with the device the Service A i customer service will gladly assist you th mann LED PAR MUSIC IS OUR PASSION General notes 1 2 Notational conventions This manual uses the following notational conventions Letterings The letterings for connectors and controls are marked by square brackets and italics Examples VOLUME control Mono button Displays Texts and values displayed on the device are marked by quotation marks and italics Examples 24ch
6. UR PASSION 11 Safety instructions WARNING Eye damage caused by high light intensity Never look directly into the light source WARNING Risk of epileptic shock Strobe lighting can trigger seizures in photosensitive epilepsy Sensitive persons should avoid looking at strobe lights NOTICE Risk of fire Do not cover the device nor any ventilation slots Do not place the device near any direct heat source Keep the device away from naked flames th mann LED PAR MUSIC IS OUR PASSION 12 Safety instructions NOTICE Operating conditions This device has been designed for indoor use only To prevent damage never expose the device to any liquid or moisture Avoid direct sunlight heavy dirt and strong vibrations NOTICE Power supply Before connecting the device ensure that the input voltage AC outlet matches the voltage rating of the device and that the AC outlet is protected by a residual current circuit breaker Failure to do so could result in damage to the device and possibly injure the user Unplug the device before electrical storms occur and when it is unused for long periods of time to reduce the risk of electric shock or fire PARS6 10MM UV th mann MUSIC IS OUR PASSION 13 Features 3 Features themann MUSIC IS OUR PASSION 14 Special features of this device 144 x UV LEDs Operation in stand alone master slave or DMX mode Very simple operation via butto
7. a new value To return to the previous menu level without changes press M for menu structure see Chapter 7 Opera tion on page 25 PAR56 10MM UV th mann MUSIC IS OUR PASSION 25 Operation DMX address Manual test themann MUSIC IS OUR PASSION Press M Press one of the arrow keys repeatedly until the display DMX Press OK Now you can set the number of the first DMX channel to be used by the device DMX address Use the arrow keys to select a value between 1 and 512 the display shows A001 A512 When the display shows the desired value press OK to confirm the selection Then press M to return to the higher menu level To return to the higher menu level without changes press M Make sure that this number matches the configuration of your DMX controller The highest possible start address for the 2 channel DMX mode is 511 Press M Press one of the arrow keys repeatedly until the display shows TEST Press OK This operating mode can be used to test the strobe effect speed STRO and the dimmer set ting DIMM to change both settings and to operate the device in stand alone mode LED PAR 26 Operation Operating mode Show Master Press the M button Press one of the arrow keys repeatedly until the display shows LINE Press OK Press one of the arrow keys repeatedly until the display shows MA Press OK Now you can select one of
8. c sound activated synchronized show This function is ideal when you want to start a show immediately Connect the DMX output of the master device to the DMxX input of the first slave device Then connect the DMX output of the first slave device to the DMX input of the second slave device and so on PAR56 10MM UV th mann MUSIC IS OUR PASSION 21 Connections and controls 6 Connections and controls Rear panel th mann LED PAR MUSIC IS OUR PASSION 22 4 5 Power cord Display OK button Confirms a selected value Buttons Increases decreases the displayed value by one M button Calls the main menu or a submenu Bracket for floor placement or hanging Locking screws for the mounting bracket PAR56 10MM UV Connections and controls themann MUSIC IS OUR PASSION 23 Connections and controls 9 DMXIN DMX input 10 DMX OUT DMX output th mann LED PAR MUSIC IS OUR PASSION 24 Operation 7 Operation 7 1 Starting up the device Connect the unit to the power grid to start operation The device is immediately ready to use and operates in the last active mode with the last selected settings 7 2 Main menu Menu operation Press M to open the main menu Use the arrow keys to select the desired parameter or to change the respectively indicated value When the display shows the desired parameter or value press OK to enter the respective submenu or to confirm
9. e Center You can find the contact information at www thomann de PAR56 10MM UV th mann MUSIC IS OUR PASSION 35 Cleaning 11 Cleaning Optical lenses Clean the optical lenses that are accessible from the outside regularly in order to optimize the light output The frequency of cleaning depends on the operating environment wet smoky or particularly dirty surroundings can cause more accumulation of dirt on the optics of the device M Clean with a soft cloth using our lamp and lens cleaner item no 280122 Always dry the parts carefully th mann LED PAR MUSIC IS OUR PASSION 36 Protecting the environment 12 Protecting the environment Disposal of the packaging mate rial For the transport and protective packaging environmentally friendly materials have been chosen that can be supplied to normal recycling Ensure that plastic bags packaging etc are properly disposed of Do not just dispose of these materials with your normal household waste but make sure that they are collected for recycling Please follow the notes and markings on the packaging Disposal of your old device This product is subject to the European Waste Electrical and Electronic Equipment Directive WEEE Do not dispose with your normal household waste Dispose of this device through an approved waste disposal firm or through your local waste facility When discarding the device comply with the rules and regulations that apply
10. eys to select a value between 0 and 255 the display shows D000 D255 This setting is only relevant if the device is not controlled via DMX When the display shows the desired value press OK to confirm the selection Then press M to return to the higher menu level To return to the higher menu level without changes press M PAR56 10MM UV th mann MUSIC IS OUR PASSION 29 Operation 7 3 Menu overview MEN Cm ms Cm I Com ma Ce RE ass CF mn Cosmo Comm th mann LED PAR MUSIC IS OUR PASSION 30 Operation 7 4 Functions in 2 channel DMX mode Channel Value Function 1 0 255 Dimmer 0 to 100 2 0 255 Strobe effect 0 to 100 PARS6 10MM UV th mann MUSIC IS OUR PASSION 31 Technical specifications 8 Technical specifications Lamp Number of DMX channels Mains power supply Power consumption Dimensions W x H x D Weight themann MUSIC IS OUR PASSION 32 144 x 10 mm LEDs UV 400 410 nm 2 230 V AC 50 Hz 10W 205 mm x 210 mm x 220 mm 1 6 kg LED PAR Plug and connection assignments 9 Plug and connection assignments Introduction This chapter will help you select the right cables and plugs to connect your valuable equip ment so that a perfect light experience is guaranteed Please take our tips because especially in Sound amp Light caution is indicated Even if a plug fits into a socket the result of an i
11. in your country If in doubt consult your local waste disposal facility PAR56 10MM UV th mann MUSIC IS OUR PASSION 37 Notes th mann LED PAR MUSIC IS OUR PASSION 38 Musikhaus Thomann e K Treppendorf 30 96138 Burgebrach Germany www thomann de
12. ncorrect connection may be a destroyed DMX controller a short circuit or just a not working light show DMX connections The unit offers a 3 pin XLR socket for DMX output and a 3 pin XLR plug for DMX input Please refer to the drawing and table below for the pin assignment of a suitable XLR plug Pin Configuration 1 Ground shielding 2 Signal inverted DMX cold signal 3 Signal DMX hot signal PARS6 10MM UV th mann MUSIC IS OUR PASSION 33 Troubleshooting 10 Troubleshooting NOTICE Possible data transmission errors For error free operation make use of dedicated DMX cables and do not use ordi nary microphone cables Never connect the DMX input or output to audio devices such as mixers or ampli fiers In the following we list a few common problems that may occur during operation We give you some suggestions for easy troubleshooting th mann LED PAR MUSIC IS OUR PASSION 34 Troubleshooting Symptom Remedy The unit does not work no Check the mains connection and the fuse light No response to the DMX con 1 Check the DMX ports and cables for proper connection troller 2 Check the address settings and the DMX polarity 3 Try using another DMX controller 4 Check to see if the DMX cables run near or alongside to high voltage cables that may cause damage or interfer ence to DMX interface circuits If the procedures recommended above do not succeed please contact our Servic
13. ns and display on the unit Robust metal housing with detachable grille Ideal for clubs bars stages exhibitions and many more applications LED PAR Installation 4 Installation Unpack and carefully check that there is no transportation damage before using the unit Keep the equipment packaging To fully protect the device against vibration dust and moisture during transportation or storage use the original packaging or your own packaging material suitable for transport or storage respectively WARNING Risk of injury caused by falling objects Make sure that the installation complies with the standards and rules that apply in your country Always secure the device with a secondary safety attachment such as a safety cable or a safety chain PARS6 10MM UV th mann MUSIC IS OUR PASSION 15 Installation themann MUSIC IS OUR PASSION NOTICE Risk of overheating Always ensure sufficient ventilation The ambient temperature must always be below 40 C 104 F NOTICE Use of stands When mounting the device onto a stand ensure that the stand is in a safe and stable position and that the weight of the device does not exceed the maximum permissible load capacity of the stand LED PAR 16 Installation NOTICE Possible data transmission errors For error free operation make use of dedicated DMX cables and do not use ordi nary microphone cables Never connect the DMX input or output to audio devices
14. such as mixers or ampli fiers Mounting options You can install the device standing or hanging upside down When in use the device must be mounted at a solid surface or clamped to an approved truss Use the openings of the bracket provided for mounting Work from a stable platform whenever you install or move the device or when you perform any kind of maintenance Block access under the work area The safety cable must be attached to the bracket PARS6 10MM UV th mann MUSIC IS OUR PASSION 17 Installation Please note that this device must not be connected to a dimmer 11 th mann LED PAR MUSIC IS OUR PASSION 18 Starting up 5 Starting up Establish all connections as long as the unit is switched off Use the shortest possible high quality cables for all connections PAR56 10MM UV th mann MUSIC IS OUR PASSION 19 Starting up Connections in DMX mode Connect the DMX input of the device to the DMX output of a DMX controller or another DMX device Connect the output of the first DMX device to the input of the second one and so on to form a daisy chain Always ensure that the output of the last DMX device in the daisy chain is terminated with a resistor 110 O W 2 cco n th mann LED PAR MUSIC IS OUR PASSION 20 Starting up Connections in master slave When you configure a group of devices in master slave mode the first unit will control the mode other units for an automati
15. y other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage No liability will be assumed for damages resulting from improper use This device may be used only by persons with sufficient physical sensorial and intellectual abilities and having corresponding knowledge and experience Other persons may use this device only if they are supervised or instructed by a person who is responsible for their safety DANGER Danger for children Ensure that plastic bags packaging etc are disposed of properly and are not within reach of babies and young children Choking hazard Safety Ensure that children do not detach any small parts e g knobs or the like from the unit They could swallow the pieces and choke Never let children unattended use electrical devices th mann LED PAR MUSIC IS OUR PASSION 10 Safety instructions DANGER Electric shock caused by high voltages inside Within the device there are areas where high voltages may be present Never remove any covers There are no user serviceable parts inside Do not use the device if covers protectors or optical components are missing or damaged DANGER Electric shock caused by short circuit Do not modify the mains cable or the plug Failure to do so could result in electric shock death or fire If in doubt seek advice from a registered electrician PAR56 10MM UV th mann MUSIC IS O
Download Pdf Manuals
Related Search