PassThru CAN User`s Manual
Contents
1. 101 Normal End Yes 102 Abnormal End No 103 Timeout error No 104 Abort conditions error No AN If the above does not apply Shift fork Teach In has not been performed correctly and start over from 1 Preparation again 4 Turn IG switch to LOCK OFF position Turn IG switch to LOCK or OFF position and reset TC SST ECU Page 26 of 46 Ei PassThru CAN User s Manual MITSUBISHI MOTORS An error dialog is displayed Click OK button and screen moves back to the main screen x Communication error ECU no response Check hamess connection or IG SUN Displaying the error dialog is normal processing of the PassThru CAN software Put the vehicle into the condition below again Engine Idling Shift lever position P range Brake pedal Depressed Parking brake Pulled Transmission fluid temperature 40 C to 80 C 104 F to 176 F A Please make sure the vehicle is in the above condition Otherwise Teach in procedure will not be continued correctly Press PassThru CAN Teach in button ESCH EEN eneen PassThru CAN Reader PassThru CAN Flash PassThru CAN Coding A AN S 5 Clutch Ventilation Confirm datalist value of No 100 Teach in executing is No Teach In executing Page 27 of 46 sa PassThru CAN User s Manual MITSUBISHI MOTORS Select Clutch Ventilation Click OK butt2. The ECU has the latest update and reprogramming is not necessary 5 Search result Case 2 When the vehicle is not applied to the reprogramming data this dialog screen will appear Press OK button and return to the main screen The information read out from the target vehicle does not match reprogramming data file information and the reprogramming file can not be applied to the vehicle 6 Confirmation of flash reprogramming This screen will appear to confirm reprogramming Press OK button to continue Note Once you press the button reprogramming starts If you press cancel button Ed you will go back to the Automatic Reprogramming CAN screen AC Some Vehicles turns on radiator fans during reprogramming DO NOT get closer to radiator fans 7 The ECU reprogramming is now in progress The PCM reprogramming is now in progress The reprogramming status is displayed as blue area of the progress bar AS Please be careful not to disconnect the cables between PC and the vehicle until the reprogramming is complete Ci nplete reprogramming 4 Complete reprogramming a MITSUBISHI MOTORS On board ECU has reprogrammed ECU Part No 1860A726 SAWN Part No 1860A72602 MASS 4 Unnecessary reprogramming It does not have appropriate reprogramming data ECU Part Ho 13604726 SAV Part No 1860A72602 Mann Leck reprogramming cata Reprogram ECU OK File Name 1862A782
3. A Choose the correct vehicle from the list 3 Confirmation screen This screen will appear to confirm registration 4 Registration confirmation Please press OK button to continue Perform key code registration OK Note Once you press the button ae starts If you press cancel button you go back to the Key Code Registration screen 4 Complete screen When this screen appears Key Code Registration A Complete Registration is complete Key Code Registration is complete Press OK button and return to the main Click OK to finish screen bd I Page 18 of 46 Ei PassThru CAN User s Manual MITSUBISHI MOTORS 9 PassThru CAN Coding 1 Main menu screen The main screen appears Press PassThru CAN Coding button 2 Coding information screen The Variant Coding screen will appear and the following information is displayed in the table 1 VIN 2 ECU Hardware Part No 3 Coding file name A O Writing of the wrong coding data may lead to inappropriate behavior of the vehicle So check and confirm if the coding information in the table is correct for the vehicle 3 Confirmation screen This screen will appear to confirm coding Please press OK button to continue Note Once you press the button coding starts You can also go back to the main screen by clicking cancel button 4 Complete screen When this screen appears coding is complete a
4. NRC XX Other error Teach in lt Possible cause gt This error resulted from other causes that are x ueu not described in this error list i F lt Remedy gt ti hee une E Restart Teach in from the beginning and retry If the same error occurs write down the NRC code in XX field of the error dialog and le leg contact Mitsubishi Motors North America Inc Page 45 of 46
5. No A 101 Normal End No The function may take several minutes to l complete Wait until the value changes to No e wien E ti Time TO y v E M ee 104 bort conditior j If vehicle conditions are not met Pending is displayed e t t T tch When No 100 Teach in executing is No Check the other data Check if value of data list items are as follows 101 Normal End Yes 102 Abnormal End No 103 Timeout error No 104 Abort conditions error No A If the above does not apply Stroke Teach In has not been performed correctly and start from 1 Preparation again 7 Boost Teach In Confirm datalist value of No 100 Teach in executing is No Page 29 of 46 sa PassThru CAN User s Manual mi Select Boost Teach In Click OK button and execute the function Clutch Ventilation Check Data list status While No 100 Teach in executing is Yes Boost Teach In is ongoing Wait until the value turns No A 101 Normal End No If vehicle conditions are not met Pending is f f displayed 102 Abaone End N 103 Timeout error Ne L ei D A MaHONS emor H While the function is operational be careful with the followings f i eThe engine speed could be high 4 000 r min several times when the Boost Teach In is in progress Depending on the transaxle s
6. TC SST Electrical Control Unit Diagnostic Trouble Code Power train Control Module Control Area Network Vehicle Identification Number Twin Clutch Sportronic Shift Transmission MITSUBISHI MOTORS Page 5 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS 1 Overview 1 1 Function overview PassThru CAN software has the following functions Function name Description This function allows the user to retrieve information from an ECU of the vehicle This information is necessary to search correct files such as flash reprogramming data file coding data and other files for the target vehicle program Immobilizer This function allows the user to re register Immobilizer Key Code into PCM in its replacement Variant Coding This function allows the user to writes coding data information on vehicle equipment into PCM VIN Writing This function allows the user to write VIN into PCM Teach in This function allows the user to execute TC SST re learn process that is necessary in case of the following service 1 Mechatronic assembly part replacement 2 Clutch assembly part replacement As for the details of the above service refer to related TSB and instruction on website Note This function is executable for vehicles equipped with TC SST only TC SST is abbreviation of Twin Clutch Sportronic Shift Transmission and is equipped for some high performance Mitsubishi vehicles 1 2 Main menu screen
7. 7 Teach in In se EEN the following support files d a Pass ThruCG AN need to be installe Do i CBF file gp MiB Gee Date CBF file is a database file for Teach in with cbf as its file CC DiseDE extension Install the CBF file in the following path o JE cEeF i Local Disk Program Files PassThruCAN DiagDB CBF El GBF ii TIPart file axe CID TIPart file is a vehicle information file with tipart as its file Ba hi extension Install the TIPart file in the following path 91 Menu Local Disk Program Files Pass ThruCAN DiagDB XML Ga Roe Data H E ayate m 14 Temp AO Only one TIPart file must exist in the folder The file name is TL Info tipart and file with other name can not be recognized by PassThruCAN software When the previous TIPart file exists please delete the file and install only 1 TiPart file for the target vehicle 3 Uninstallation Note PassThru CAN is uninstalled in 2 steps Main software program is uninstalled from the system menu of Windows Control Panel and Library is uninstalled from the system menu of Windows Control Panel 1 Control Panel Screen E CC rz zt o D se Fes Herr NB xa Ea idies 2 Ca al Paral sl Aco Select Settings Control Panel from the Start menu Choose and double click Add Remove programs FE Lii hPa al i Pa bo p r ai mon amp One KOR Comper Select an bem bo whew ES eer a Weien adati es
8. End Yes 102 Abnormal End No 103 Timeout error No 104 Abort conditions error No AN If the above does not apply Reset clutch gain has not been performed correctly and start from 1 Preparation again 9 Complete When all the Teach in commands required for Mechatronic assembly replacement are executed turn IG switch to LOCK or OFF position and finish the procedure Page 31 of 46 Ei PassThru CAN User s Manual MITSUBISHI MOTORS Procedure for clutch assembly replacement 1 Preparation With the PC and PassThru device connected to the vehicle put the vehicle into the condition below eEngine Idling Shift lever position P range Brake pedal Depressed Parking brake Pulled Transmission fluid temperature 40 C to 80 C 104 F to 176 F A Please make sure the vehicle is in the above condition Otherwise Teach in procedure will not start correctly 2 Clutch Ventilation Confirm datalist value of No 100 Teach in executing is No Select Clutch Ventilation Click OK button and execute the function Check Data list status While No 100 Teach in executing is Yes Clutch Ventilation is ongoing Wait until the value turns No A The function may take several minutes to complete Wait until the value changes to No A If vehicle conditions are not met Pending
9. Press OK button B ano return to the main screen PassThru CAN Reader PassThru CAN Flasi ll PassThru CAN Coding PassThru CAN Immobilizer Erase DTCs PassThru CAN Vi N ES CT ihe rem n of coding Perform coding OK Complete coding Variant coding is complete Click OK to finish LTL Page 19 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS 10 PassThru CAN VIN Writing 1 Main menu screen The main screen appears PassThru CAN Reader PassThru CAN Flash PassThru CAN Coding Press PassThru CAN VIN Writing button ES SS PassThru CAN Immobilizer Erase DTCs PassThru CAN VIN Writing 2 VIN input screen The VIN Input screen will appear Please input the new VIN Press OK button on the screen AN In case of new ECU the VIN information in Current VIN field is filled with asterisk You can go back to the first screen by clicking return r A 4 G i i TTT button 3 Confirmation screen This screen will appear to confirm writing 5 D Confirmation of VIN Writing Please press OK button to continue A Perform YIN Writing OR Note Once you press the button writing starts If you press cancel button Ed you will go back to the VIN Writing screen 4 Complete screen When this screen wae writing is complete Press OK button and return to the main screen VIN Writing is complete Click OK to finish Complete VIN Wr
10. again 5 Reset clutch gain Confirm datalist value of No 100 Teach in executing is No This procedure is unnecessary for vehicle with diagnostic version of 0001 Select Reset clutch gain Click OK button and execute the function Check Data list status While No 100 Teach in executing is Yes Reset clutch gain is ongoing Wait until the value turns No A The function may take several minutes to complete Wait until the value changes to No A If vehicle conditions are not met Pending is displayed No Name Vake Page 35 of 46 PassThru CAN User s Manual When No 100 Teach in executing is No Check the other data Check if value of data list items are as follows 101 Normal End Yes 102 Abnormal End No 103 Timeout error No 104 Abort conditions error No AN If the above does not apply Clutch Ventilation has not been performed correctly and start over from 1 Preparation again 6 Complete ae MITSUBISHI MOTORS When all the Teach in commands required for Clutch assembly replacement are executed turn IG switch to LOCK or OFF position and finish the procedure Page 36 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS 11 Error List When an error message is displayed check the following table for inform
11. following path Local Disk Program Files Pass ThruCAN DiagDB CBF ii IMPart file IMPart file is a vehicle information file with impart as its file extension Install the Man file in the following path Local Disk Program Files Pass ThruCAN DiagDB XML AO Only one IMPart file must exist in the folder When the previous IMPart file exists please delete the file and install only 1 IMPart file for the target vehicle 6 VIN Writing In order to execute VIN Writing the following support files need to be installed i CBF file CBF file is a database file for VIN Writing with cbf as its file extension Install the CBF file in the following path Local Disk Program Files Pass ThruCAN DiagDB CBF ii VWPart file VWPart file is a vehicle information file with vwpart as its file extension Install the VWPart file in the following path Local Disk Program Files Pass ThruCAN DiagDB XML A O Only one VWPart must exist in the folder When the previous VWPart file exists please delete the file and install only 1 VWPart file for the target vehicle D de Fass Thru at ia cxn 0 E d De De BE ii a Rope Data H System 9 Temp EL D Pass TbruCGoh CC CdeData o Dies DB acer i 3 GBF fax fii a Be Menu H E RpeData Ga md Slenm GL Temp EL D Pass Thu oh CC CdeData D 1 Dee Dp H E Rpe Data H System H Temp Page 9 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS
12. is displayed Page 32 of 46 Ei PassThru CAN User s Manual MITSUBISHI MOTORS When No 100 Teach in executing is No Check the other data Check if value of data list items are as follows 101 Normal End Yes 102 Abnormal End No 103 Timeout error No 104 Abort conditions error No AN If the above does not apply Clutch Ventilation has not been performed correctly and start over from 1 Preparation again 3 Stroke Teach In Confirm datalist value of No 100 Teach in executing is No Select Stroke Teach In Click OK button and execute the function No Piausibiity check Shift fork Teach In Line pressure Test Stroke Teach In D 4 E Ca i 2 Interlock Teach In Boost No Name Vate Clutch Vergitapnon Check Data list status While No 100 Teach in executing is Yes Stroke Teach In is ongoing Wait until the value turns No A The function may take several minutes to Sam complete Wait until the value changes to No goe e i t 103 Timeout error Ne Lem emm een Dy Ab ronditions error to If vehicle conditions are not met Pending is displayed Page 33 of 46 PassThru CAN User s Manual When No 100 Teach in executing is No Check the other data Check if value of data list items are as follows 10
13. make sure the Device ts connected to the vehicle Please turn the ignition key ON The ENGINE should be OFF 2 System select screen A table is displayed for system selection Select the system from which you want to read out ECU information Press OK button and read out of ECU information starts If you press return button a you will go back to the previous screen 3 Confirmation screen Read ECU part number Read ECU part number Read out of ECU information is in progress Read ECU Hardware part number and Software part number and VIN Please wait sss ECU part number D ECU part number 4 ECU information screen When read out is successful the following information is displayed 1 ECU Part No ECU Part No MR569715 B 2 ECU Software Part No S W Part No abedefghip 3 VIN VIN No 123456789 ABCDEFG Press OK button and the screen goes back to the main menu screen O LS ECU information is necessary for reprogramming data file search Coding file search and for other purpose Record the necessary information Page 13 of 46 PassThru CAN User s Manual 6 PassThru CAN Flash 1 Main menu screen The main screen will appear Click PassThru CAN Flash button to execute ECU reprogramming After execution the software starts communication with an ECU to retrieve necessary information of the vehicle 2 Search screen This screen is displayed while the so
14. of 46 Ei PassThru CAN User s Manual MITSUBISHI MOTORS 5 Confirmation screen A Command name The selected command wall be executed Are you sure Please confinn the on item and condition Press OK button and return to the main screen If you press cancel button EX you will go back to 4 Teach in command selection screen 6 Executed screen G Executed The selected recalibration command was executed Please review each data list item for status and result Press OK button and return to 4 Teach in command selection screen Repeat the above 4 to 6 to execute necessary Teach in commands that are required for related service Refer to the following part for detailed Teach in procedure Procedure for mechatronic assembly replacement 1 Preparation With the PC and PassThru device connected to the vehicle put the vehicle into the condition below Engine Idling eShift lever position P range Brake pedal Depressed Parking brake Pulled Transmission fluid temperature 40 C to 80 C 104 F to 176 F A Please make sure the vehicle is in the above condition Otherwise Teach in procedure will not start correctly 2 Plausibility check Start the PassThruCAN Teach in Confirm datalist value of No 100 Teach in executing is No Page 24 of 46 sa PassThru CAN User s Manual MITSUBISHI MOTORS Select Plausibilit
15. 1 Normal End Yes 102 Abnormal End No 103 Timeout error No 104 Abort conditions error No AN If the above does not apply Stroke Teach In has not been performed correctly and start over from 1 Preparation again 4 Boost Teach In Confirm datalist value of No 100 Teach in executing is No Select Boost Teach In Click OK button and execute the function Check Data list status While No 100 Teach in executing is Yes Boost Teach In is ongoing Wait until the value turns No A If vehicle conditions are not met Pending is displayed A While the function is operational be careful with the followings eThe engine speed could be high 4 000 r min when the Boost Teach In is in progress Depending on the transaxle state the engine speed may not be high The function may take several minutes to complete Wait until the value changes to No a MITSUBISHI MOTORS Page 34 of 46 sa PassThru CAN User s Manual MITSUBISHI MOTORS When No 100 Teach in executing is No Check the other data Check if value of data list items are as follows 101 Normal End Yes 102 Abnormal End No 103 Timeout error No 104 Abort conditions error No A If the above does not apply Boost Teach In has not been performed correctly and start over from 1 Preparation
16. A Part No read out error SCH target vehicle Read out hardware part number didn t match VCPart lt Remedy gt file data Apply the correct vehicle Reinstall correct VCPart file LLL Page 40 of 46 11 VIN error Coding VIN error VIN writing CA VIN error VIN read out was not successful Ei PassThru CAN User s Manual MITSUBISHI MOTORS Me Error dialog ae Cause Remedy 15 CRC error S error Coding lt Possible cause gt f Coding file may be damaged and its data is changed lt Remedy gt Reinstall the correct coding data file and retry Update Flash Data Web A MA POU Q CRC error CRC error occurred Please reinstall coding data file and retry 16 Coding data mismatch Coding lt Possible cause gt The coding data may have been written wrongfully due to bad communication between vehicle and PC lt Remedy gt Check harness PassThru device and battery voltage of the vehicle Update Flash Data Web Z S4 poe A Coding data mismatch Written coding data didn t match coding data file Please retry PA 17 Coding lt Possible cause gt wm Target ECU doesn t support variant coding function GE Coding error lt Remedy gt Target ECL doesn t Suppor Check if the vehicle is compatible with variant variant coding function coding functionality ECLA NRC XX Other error in coding Coding lt Possible cause gt This error is resulted from other causes that are
17. PassThru CAN Programming of Emission Related Control Units With PassThru Programming System SAE J2534 Compliant User s Manual lt Ver 1 6 gt Ki MITSUBISHI MOTORS PassThru CAN User s Manual MITSUBISHI MOTORS Foreword This manual explains operating procedures and other related information for Pass Thru CAN software The user is required to read this manual carefully and to follow the described procedure for appropriate software usage Page 2 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS Table of Contents 1s e UTC 6 2 a LAN de EE 7 2 SUPPONI file INSTAN AU OM s reisos auenien naana araa inaa ani aa 8 Ss Estelle 10 4 Starting of PassThru CAN ccccssssescssssseccnssssccnnessccnnsesecsnassccenssssnensesssennes 12 5 PassThru CAN Reader cispeainsec casa cane asec ec sseetuneteveneranentesesetseeuanneaterusnaeseweeus cutee 13 6 Pass hru CAN FS E 14 m ASS A e 17 8 PassThru CAN Immobilizer asnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 18 9 PassThru CAN Coding E 19 10 PassThru CAN VIN Writing cccccccteesseeseeeesseeeeseenseeeeeeeeseeeseoenseesseoenneeeseons 20 11 PassThru CAN Teachiin ME 21 ND ETOF LIS EE 37 Page 3 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS Symbols for safety operation The following symbols are used for your safety and correct operation of the software See Veto This symbol alerts you to a procedure or practice which
18. The buttons for the above functions are located on the main menu screen as follows Please refer to the related part in the following section for instruction on how you can operate each function gd PassThru CAN Reader PassThru CAN Flash PassThru CAN Coding PassThru CAN Immobilizer Erase DTCs PassThru CAN VIN Writing PassThru CAN Teach in MMC PassThru CAN Version 3 0 2 Please check the cable connectors and insulation for wear or damage DO NOT use questionable cable ase make sure the Device is connected to the vehicle Please turn the ignition Key ON The ENGINE should be OFF Page 6 of 46 PassThru CAN User s Manual 2 Installation 1 Pass CAN Installer file Put PassThru CAN installer file into any folder 2 Installation You can find Setup exe icon in installer file Choose and double click the icon to start installation A O Please make sure that PassThru CAN is NOT already installed When PassThru CAN is already installed Setup exe detects and moves on to uninstallation process and the software will be deleted 3 Installation procedure is now in progress Installation process automatically starts and its progress is displayed with blue area 5 Complete When installation is complete PassThru CAN icon is created on desktop Setip exe Installshield Wizard 4 xj L 1 Selup Slalus FasThu CAH Setup G Gerbe the prp waled opuinions Insekte PassThru CAM Pag
19. ZO sent oh ee Por oral iahap Co u La Aa La Parr Det Pinter Magka Siara w hhi Ophions Cameras Ss 4 amp 2 Sarek wei Srii Ukert sel wired Link hh rre a Fesoni D obini LSS F Tonbe 2 Add Remove Programs Screen Select PassThru CAN and press Change Remove button Uninstallation of PassThru CAN is implemented Page 10 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS 3 Add Remove Programs Screen Select CGDPTMC Library and press Remove button The confirmation screen will appear Click Yes button SE Uninstallation of CGDPTMC Library is implemented el T si All the procedure to uninstall PassThru CAN software is complete 4 Uninstallation of support files Support files that are installed manually remain after uninstallation of PassThru CAN software Uninstall manually those files together with their folders Page 11 of 46 PassThru CAN User s Manual 4 Starting of PassThru CAN 1 PassThru CAN desk top icon After installation of PassThru CAN PassThru CAN icon is created on desktop screen To start the application double click the icon 2 Main menu screen The main screen will appear and functions are either activated or deactivated according to type or service Select and press the active button you want to execute Note If you want to exit PassThru CAN press cancel button on the screen The version of t
20. _dio30 cff 2 Check reprogramming data ME ices Fragrogrenrereny Siri Page 15 of 46 Ei PassThru CAN User s Manual MITSUBISHI MOTORS 8 Complete screen 1 When this screen appears Reprogramming is complete Confirm ECU information after reprogramming Press OK button 9 Complete screen 2 Follow the screen instruction to complete the reprogramming procedure Press OK button and return to the main screen AQ To complete flash reprogramming turn OFF IG switch and then turn it ON Go back to the main menu screen and execute Erase DTCs function 10 Post process After finishing reprogramming it is recommended that you will check whether the ECU stores DTC or not with your own scan tool If any DTCs exist please clear them If you want to reprogram another ECU successively please exit and restart PassThru CAN otherwise an error message will appear 4 Completed Reprogramming is complete ECU Part No 1860A726 SAN Part No 1860A72602 1 Completed Please turn OFF IG switch for a while and then turn it ON Retur to the main menu and execute OTC Cleanig function LTL Page 16 of 46 PassThru CAN User s Manual 7 Erase DTCs 1 Main menu screen Press Erase DTCs button 2 Confirmation screen This screen will appear to confirm erasing Please press OK button to continue Note Once you press the button erasing starts If yo
21. ach in procedure refer to the following section After reprogramming of TC SST ECU with PassThru CAN Flash DTC may be stored in other ECUs on the vehicle Refer to the section 7 Erase DTCs and clear DTCs Here is a matrix related with Teach in commands and Diagnostic version Teach in sequence for Teach in sequence for Teach in commend Diag Ver Diag Ver Diag Ver Mechatronic Clutch assembly name 0000 0001 0002 assembly replacement replacement Plausibility check 1 ma availabe available il Shiftfork Tesch 1 na availabe available 2 7 available available Line pressure Test n a but not but not used used Stroke Teach In Bet f wa fae seas O t fk BoostTeach In Teach In available available EE Interlock Teach In but not but not GE D Clutch Ventilation ot Reset clutch gain available Note Line pressure Test and Interlock Teach In are not used during the Here is another matrix for additional procedures flash and coding Di tic Version 0000 Mechatronic ee EE Out assembly Required Required Se Unnecessary JAs for 2008 Lancer Evolution with TC SST unit After Teach in executed TC SST ECU must be reprogrammed back to the previous level of calibration Refer to the related TSB and instruction on website for details Page 22 of 46 PassThru CAN User s Manual Teach in procedure in details 1 Main menu screen The main screen appears Press PassThru CAN Teach in
22. ation Note If error reoccurs even after trying the described procedure for remedy please contact with MITSUBISHI Cam NORTH AMERICA Inc Error dialog Eordilog Function Cause Remedy ee error Flash lt Possible Cause gt Coding Oc Communication error Immobilizer 1G SW is not ON or battery is too low Harness and ECU are damaged VIN writing Teach in ECU no response Check harness Harness is not connected correctly connecting or IO SW lt Remedy gt Check IG SW and battery voltage Check harness and ECU damage and fix Connect harness correctly aie Wi Reader lt Possible Cause gt IG SW is not ON or battery is too low Harness and ECU are damaged EEE E EE Harness is not connected correctly inati CBF file can not be found in the specified lt Remedy gt x communication error ECU no response Check harness folder connecting or IO SW Check IG SW and battery voltage Check harness and ECU damage and fix Connect harness correctly Install CBF file EmA When CBF file is not installed correctly this error dialog is also displayed Reader function only o File search error FIPart file error Flash lt Possible Cause gt e Flat file is not installed correctly lt Remedy gt File search error Install FlPart file correctly FiPart file was not found Install correct Flat file and retry FlPart file is an information file that has flpart as an extentio
23. button 2 Confirmation screen Press OK button when vehicle is ready for service If you press cancel button EX you will go back to Main menu screen In case MIL is on and DTC is output Teach in may not operate correctly Refer to the related part of service manual and fix the problem first 3 Search screen This screen is displayed while the software is communicating with an ECU After retrieving the ECU information PassThru CAN checks it with Teach in data file information Wait for a while until the process is complete 4 Teach in command selection screen When this screen appears you can select and execute Teach in command Result of Teach in command can be checked from the data in the right table Select the A Teach in command and press OK button You cani back to menu screen by clicking return button as sa MITSUBISHI MOTORS PassThru CAN Flash PassThru CAN Coding PassThru CAN VIN Writing PassThru CAN Immobilizer Erase DTCs PassThru CAN Reader E PassThru CAN Teach in MMC PassThru CAN Version 3 0 Please check the cable DO NOT use questionable cables Please make sure the Device is connected This function will recalibrate TC SST Do NOT proceed when MIL or warning indicator of TC SST is ON and repair jhen A Automatic Searching the data Searching for TC SST recalibration data files Setect Teach in command and cic OW button to esecute Page 23
24. ctly Update Flash Data Web A 3 Pos gt File search error lt Remedy gt Install coding data file correctly Coding data file was not found Reinstall data file and retry AN a EZ E Coding data file has kon as its file extension lt Possible cause gt PCM or PassThru device are damaged Harness is disconnected while read out lt Remedy gt Check harness connection and battery voltage supply from the vehicle and retry Repair or replace PCM or PassThru device Please retry WS ETH 12 Goaing lt Possible causes engen Wrong vehicle is selected for Coding E VIN error Wrong VCPart file is installed and is not for the B target vehicle a oe eee PCM is newly replaced and VIN is not yet written lt Remedy gt r Apply the correct vehicle ve Reinstall correct VCPart file Write VIN refer to VIN writing section 13 Part No read out error Coding lt Possible cause gt Damaged harness or disconnection Update Flash Data Web A S4 POS E Damaged PCM or PassThru device CA Part No read out error Reading out of hardware part lt Remedy gt l number was not successful Check harness is connected correctly Please retry Check if harness is damaged and change it if necessary Repair or replace PCM or PassThru device Jee 14 Part No read out error Coding lt Possible cause gt Wrong vehicle is selected for Coding a Raa Wrong VCPart file is installed and it is not for C
25. e 7 of 46 MITSUBISHI MOTORS PassThru CAN User s Manual MITSUBISHI MOTORS 2 Support file Installation In order to execute the PassThru CAN software function support files related with each function need to be installed 1 Activation of PassThru CAN software otc32 dll needs to be installed in the following location Local Disk ProgramFiles Pass ThruCAN System Common A O PassThru CAN software only activates Reader by default and you need to install ptc32 dll to activates other functionality 2 Flash In order to execute Flash the following support files need to be installed i CBF file CBF file is a database file for Flash with cbf as its file extension Install the CBF file in the following path Local Disk Program Files Pass ThruCAN DiagDB CBF ii Flpart file Flpart file is a vehicle specific information file with flpart as its file extension Install the Flpart file in the following path Local Disk Program Files Pass ThruCAN DiagDB XML NO Only one Fipart must exist in the folder When the previous Flpart file exists please delete the file and install only 1 Fipart file for the target vehicle iii CFF file CFF file is a flash data file with cff as its file extension Install CFF file in the following path Local Disk Program Files Pass ThruCAN RpgData CFF 3 Erase DTC ClearDiagCANID ini is setting file for Erase DTC and needs to be installed in the follow
26. erene This error is resulted from other causes that Error NRC XX are not described in this error list Error occurred during Key Code lt Remedy gt all Restart Immobilizer from the beginning If the same error occurs write down the NRC code in XX field of the error dialog and contact J Mitsubishi Motors North America Inc 23 Immobilizer lt Possible cause gt There has not been response from the ECU neout erro within certain period of time Timeout error Poor data communication damaged harness There has not been response from or Pass Thru device SE EES ECU may be busy doing other processing n lt Remedy gt A Retry if error recurrs Check ECU harness and PassThru device and repair replace them if necessary 94 Unknown Key Code Immobilizer lt Possible cause gt ikea ey Cad Immobilizer ECU could not recognize the key Unknown Key Code code Key code may not be correctly registered in The k d Id not b istered Lops Dog Ger ECU could n i eene Immoibilizer ECU the key code lt Remedy gt m Check if key code is correctly registered in vV Immobilizer ECU Page 42 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS Me Error dialog Function Cause Remedy 25 Immobilizer lt Possible cause gt taint ones This error is caused by internal error of x Internal error Immobilizer ECU Immobilizer ECU may be damaged Inter
27. erformed Whereas clutch assembly replacement requires PassThru CAN Flash but PassThru CAN Coding is not necessary For the actual Teach in procedure refer to the following section As for 2008 Lancer Evolution with TC SST unit after Teach in executed TC SST ECU must be reprogrammed back to the previous level of calibration Refer to the related TSB and instruction on website for details After reprogramming of TC SST ECU with PassThru CAN Flash DTC may be stored in other ECUs on the vehicle Refer to the section 7 Erase DTCs and clear DTCs Diag Version 0001 This version of TC SST ECU supports Teach in functionality However Reset clutch gain is not Supported When mechatronic assembly is replaced PassThru CAN Flash and PassThru CAN Coding must be performed Page 21 of 46 Ei PassThru CAN User s Manual MITSUBISHI MOTORS However clutch assembly replacement doesn t require these additional procedures For the actual Teach in procedure refer to the following section After reprogramming of TC SST ECU with PassThru CAN Flash DTC may be stored in other ECUs on the vehicle Refer to the section 7 Erase DTCs and clear DTCs Diag Version 0002 This version of TC SST ECU supports Teach in functionality fully When mechatronic assembly is replaced PassThru CAN Flash and PassThru CAN Coding must be performed However clutch assembly replacement doesn t require these additional procedures For the actual Te
28. ftware is communicating with an ECU After retrieving the ECU information PassThru CAN checks it with reprogramming data file information Wait for a while until the process is complete 3 Search result screen After checking ECU information and correct reprogramming data file is found PassThru CAN displays the result data on this screen AQ Check the reprogramming information on the screen and confirm it is correct for your vehicle Press OK button on the screen to continue move on to 6 Confirmation of flash reprogramming Note You can also go back to the first screen by clicking return button E According to the reprogrammed level of the target ECU on board the following 2 cases may occur a MITSUBISHI MOTORS Pass Thru CAN Reader PassThru CAN Flash 8 ass Thru CAN Coding Erase OT ES PassThru CAN VIN Writing PassThru CAN Immobilizer PassThru CAN Teach in MMC PassThru CAN Version 3 0 2 Please check the cable connectors and insulation for wear or damage DO NOT use queslionable cables Please make sure the Device is connected to the vehicte Please turn the ignition key ON The ENGINE should be OFF E Automatic searching the data Searching reprogramming subject data Page 14 of 46 PassThru CAN User s Manual 4 Search result Case 1 If the PCM has already been reprogrammed this dialogue screen will ma Press OK button and return to the main screen
29. he application will be shown at the lower part in the screen Please make sure that you see the latest version of PassThru CAN software 3 Authorization procedure In executing PassThru CAN function this screen may be displayed requiring authorization process You need to fill in the blank with valid subscription User ID and Password for authorization Use the same User ID and Password that you purchased at service information website of Mitsubishi Motors North America Inc An internet connection is required for authorization process MITSUBISHI MOTORS A PassThru CAM PassThru CAN Flash PassThru CAN Coding Erase DTCs PassThru CAN VIN Writing Authorization Required x Authorization Procedure This version of Update manager requires a valid subscription from www MitsubishiTechInfo com for activation You must be connected to the internet during the authorization process Enter your subscription user id and password and click the authorization button Once authorized you will be able to complete up to 3 re flash procedures Every 3 re flash procedures you will need to repeat Page 12 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS 5 PassThru CAN Reader 1 Menu screen hate p Press PassThru CAN Reader button to start the ESS erc function MMC PassThru CAN Version 3 0 2 Please check the cable connectors and insulation for wear or damage DO NOT use questionable cables e
30. if not arnin followed correctly could lead to death or serious injury This symbol alerts you to a procedure or practice which if not Caution followed correctly could lead to injury and or property damage vehicle PC etc Prohibition This symbol alerts you to a prohibited action Q Enoroment This symbol alerts you to an action that must be enforced General precautions and pre requisite Description Do not use damaged cables and PCs together with PC and cables PassThru CAN software Unless clearly specified and required do not operate the Vehicle software while the engine is running or when you are vce driving your car While operating the PassThru CAN software the vehicle Vehicle must be held still by applying parking brake or wheel wedges etc Power supply WW Ai supply necessary electricity for the software operation PassThru CAN software and related files i e flash data Software file and other support files are appropriately installed Internet Internet connection is necessary for web site authorization connection for software execution PassThru Valid J2534 1 compliant PassThru device must be used device The user has the valid subscription ID and password for User ID and password service information website of Mitsubishi Motors North America Inc http Awww mitsubishitechinto com epacarb Page 4 of 46 PassThru CAN User s Manual Abbreviations ECU DTC PCM CAN VIN
31. in the specified folder File Search error TC 55T recalibration data not found C Program Files PassThruCAN DiagDB XML Please review the PassThru software installation procedures lt Remedy gt and reinstall if necessary then retry Copy the downloaded TI_Info tipart file in the NRC XX Other error VIN Writing lt Possible cause gt the operation correct folder Page 44 of 46 Ei PassThru CAN User s Manual MITSUBISHI MOTORS Me Error dialog Function Cause Remedy 35 Teach in lt Possible cause gt CBF file is not found in the specified folder File Search error GA CG brogram Files Pass ThruCAN DiagDB CBF CHF file not found or invalid Please review the PassThru lt Remedy gt a software installation procedures Copy the downloaded CBF file in the correct and reinstall if necessary then retry folder the operation A Data file error not included in the Tl_Info tipart file ECU diagnostic version not found in lt Remedy gt aa eege Deg Check the vehicle if the vehicle is equipped _ with TC SST 36 Data file error Teach in lt Possible cause gt Diagnostic version read out from the vehicle is x Data file error Download and reinstall Tl_Info tipart file Invalid TC SST recalibration data Please contact MMNA 37 Data file error Teach in lt Possible cause gt TL_Info tipart file is corrupted or invalid lt Remedy gt ap
32. ing path Local Disk Program Files PassThruCAN Ini aay Menu ele Roe Datz El System As des Common Se Temp J Pass ThruCanW CdeData SBS Rope Data TF or 0 J System H E Temp Eg Pass ThruGaAh J CdeData H E Menu GL Ape Data H E oye te iti GL Temp Page 8 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS 4 Coding In order to execute Coding the following support files need to be installed i Coding file Coding file is Coding data file with kon as its file extension Install the Coding file in the following path Local Disk Program Files PassThruCAN CdgData ii CBF file CBF file is a database file for Coding with cbf as its file extension Install the CBF file in the following path Local Disk Program Files Pass ThruCAN DiagDB CBF iii VCPart file VCPart file is a vehicle specific information file with vcpart as its file extension Install the VCPart file in the following path Local Disk Program Files Pass ThruCAN DiagDB XML AO Only one VCPart file must exist in the folder When the previous VCPart file exists please delete the file and install only 1 VCPart file for the target vehicle 5 Immobilizer In order to execute Immobilizer key code transfer function the following support files need to be installed i CBF file CBF file is a database file for Immobilizer key code transfer function with cbf as its file extension Install the CBF file in the
33. iting LTL Page 20 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS 11 PassThru CAN Teach in A Precaution PassThru CAN Teach in is required when the following service is performed to TC SST unit Mechatronic assembly replacement Clutch assembly replacement In order to execute Teach in procedure correctly TC SST ECU must have correct diagnostic version Diagnostic version can be confirmed on the following screen refer to the procedure below regarding how you can get to the screen PassThru CAN Systemfunction J PassThruCAN Teachin Teach in je ken executing e Shift fork Teach In 101 Normal End Yes 3 Line pressure Test Boost Teach In 103 Timeout error No e Interlock Teach In Select Teach in command and click OK button to exec js fom Error Data 0000 S as Par Number 8637A379 Software Part Number F Diag Version 0002 Red circle in the above screen indicates diagnostic version information of TC SST ECU According to this value the following difference applies Diag Version 0000 This version of TC SST ECU does NOT support Teach in functionality and when mechatronic assembly or clutch assembly is replaced you need to reprogram TC SST ECU with related calibration file first to enable the ECU to support Teach in Refer to the related TSB and instruction on website for detailed reprogramming procedure When mechatronic assembly is replaced PassThru CAN Flash and PassThru CAN Coding must be p
34. n and is necessary to execute PassThru CAN Flash KT CL 2 all search error FlPart file error Flash lt Possible Cause gt Multiple FiPart files are installed Gi File search error lt Remedy gt DEET ENEE Delete unnecessary FlPart file and only one Delete unnecessary Flat file and correct FlPart file must exist retry d S Be careful not to delete correct FlPart file MA File search error CBF file error Flash lt Possible Cause gt Coding CBF file is not installed correctly VIN writing gt Wrong CBF file is installed lt Remedy gt Install correct CBF file e File search error CBF file was not found or inapplicable Reinstall correct CBF file and retry vy CBF file is a database file that has cbf as an Page 37 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS extention and is necessary to execute PassThru CAN Flash Me Error dialog Function Cause Remedy 5 File search error CFF file error Flash lt Possible Cause gt CFF file is not installed correctly File search error lt Remedy gt R ing data file CFF_fil d Was nol found Reinstall datafie and Install CFF tile correctly D CFF file is a reprogramming data file that has v cff as an extension Reprogramming Error Flash lt Possible cause gt Harness is disconnected while reprogramming Error occurred Start again from OH Reprog
35. nal error has occurred lt Remedy gt Check if Immobilizer ECU is working correctly Restart registration from beginning and retry iy contact Mitsubishi Motors North America Inc Mi 27 File open error IMPart file Immobilizer lt Possible cause gt Data in IMPart file can not be read out correctly CA File open error y IMPart file may be damaged and its content Error caused for parsing ImPart file changed lt Remedy gt Reinstall correct IMPart file and retry Mo op File search error VWPart file VIN Writing lt Possible cause gt er fs VWPart file is not correctly installed O File search error lt Remedy gt triad e waa not SEN E Reinstall correct VWPart file and retry correct VW Part fila and retry Bu VWPart file is an information file that is 7 necessary to execute PassThru CAN VIN Writing 29 CHECKDIGIT error VIN Writing lt Possible cause gt Input VIN is not valid and checkdigit gg verification failed 96 Error Code XX Other error Immobilizer lt Possible cause gt RRS This error is resulted from other causes that Erot ode oe are not described in this error list Error occurred during Key Code lt Remedy gt ae Restart Immobilizer from the beginning and retry If the same error occurs write down the NRC code in XX field of the error dialog and CA 9 CHECKDIGIT error lt Remedy gt Input VIN information is wrong Please retr
36. not described in this error list Update Flash Data Web s 24 poe e NRC XX Error occurred during variant coding lt Remedy gt Retry coding from the beginning If the same error occurs write down the NRC code in XX field of the error dialog and contact Mitsubishi Motors North America Inc ea 19 Coding lt Possible cause gt Update Flash Data Web AES 84 POM VCPart file may have been damaged while installation and information in the file can not NI File open error be read out correctly Error caused for parsing VCPart file lt Remedy gt Reinstall VCPart file and retry m n Page 41 of 46 Ei PassThru CAN User s Manual MITSUBISHI MOTORS Me Error dialog Function Cause Remedy 20 File search error IMPart file error Immobilizer lt Possible cause gt IMPart file is not correctly installed e search error i lt Remedy gt A File search error Reinstall IMPart file and retry Check if correct PI TEE E IMPart file is installed in specified location and retry F IMPart file is an information file that is necessary to execute PassThru CAN Immobilzer 24 File search error CBF error Immobilizer lt Possible cause gt CBF file is not correctly installed File search error lt Remedy gt Vehicle communication database file Reinstall correct CBF file and retry not found GJ III 22 Error NRC XX Registration error Immobilizer lt Possible cause gt S
37. on and execute the function Check Data list status While No 100 Teach in executing is Yes Clutch Ventilation is ongoing Wait until the value turns No No Name Vane A The function may take several minutes to complete Wait until the value changes to No IK Out Sro K Lem emm emm A 104 Abort conditions emor Nk If vehicle conditions are not met Pending is displayed When No 100 Teach in executing turns No Check the other data Check if value of data list items are as follows 101 Normal End Yes 102 Abnormal End No 103 Timeout error No 104 Abort conditions error No A If the above does not apply Clutch Ventilation has not been performed correctly and start over from 1 Preparation again 6 Stroke Teach In Confirm datalist value of No 100 Teach in executing is No Page 28 of 46 sa PassThru CAN User s Manual MITSUBISHI MOTORS Select Stroke Teach In Click OK button and execute the function PIausibiity check Shit fork Teachn T TI E P del iE E in Sch i q Co ki T Interlock Teach In Clutch Ventilation o reen No Name Vane Check Data list status While No 100 Teach in executing is Yes Stroke Teach In is ongoing Wait until the value turns
38. ramming Error PassThru device is not working correctly lt Remedy gt Check harness and battery Check and fix PassThru device Restart reprogramming process from the beginning Battery is too low beginning EL 7 File open error FiPart file Flash lt Possible cause gt ee Damaged FlPart file File open error lt Remedy gt FA PAARE ME a Aa Reinstall FlPart file and retry Ix File search error VCPart file Coding lt Possible cause gt REET VCPart file is not installed correctly Fil h A File search error lt Remedy gt VCPan file was not found Install Reinstall VCPart file correctly correct VCPart file and retry d e VCPart file is an information file that has sv vcpart as an extention and is necessary to execute PassThru CAN Coding File search error VCPart file Coding lt Possible cause gt Update Flash Data Web A 3 BA POS E Multiple VCPart files are installed gt File search error lt Remedy gt Multiple VCPart files were found Delete Unnecessary VCPart file Delete unnecessary VCPart file and retry Only one VCPart file is to be installed in the 4 Ra LZ specified location Page 38 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS Page 39 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS Me Error dialog Function Cause Remedy 10 File search error Coding data file Coding lt Possible cause gt es f Coding data file is not installed corre
39. tate the engine speed may not be high The function may take several minutes to complete Wait until the value changes to No When No 100 Teach in executing is No Check the other data Check if value of data list items are as follows 101 Normal End Yes 102 Abnormal End No 103 Timeout error No 104 Abort conditions error No A If the above does not apply Boost Teach In has not been performed correctly and start over from 1 Preparation again 8 Reset clutch gain Confirm datalist value of No 100 Teach in executing is No This procedure is unnecessary for vehicle with Page 30 of 46 Ei PassThru CAN User s Manual MITSUBISHI MOTORS diagnostic version of 0001 Select Reset clutch gain Click OK button and execute the function Check Data list status While No 100 Teach in executing is Yes Reset clutch gain is ongoing Wait until the value turns No 103 Normal End No s eem em mm 02 nal End by The function may take several minutes to complete Wait until the value changes to No A If vehicle conditions are not met Pending is e ene IR displayed ZZ FE H When No 100 Teach in executing is No Check the other data Check if value of data list items are as follows 101 Normal
40. u press cancel button E you go back to the main screen 3 Erasing DTC screen DTC erasing is now in progress AN The process may take more than a few minutes for some vehicles and wait until it is complete 4 Complete screen When this screen appears DTC Erasing is complete Press OK button and return to the main screen PassThru CAN Reader PassThru CAN Immoblliz Erase DTCs PassThru CAN Teach in a Erase DTCs Erase diagnosis code ldx d 4 Erasing DTCs This process may take more than a few minutes Please wait until it is completed as j D Erase DTCs Complete fy LI Page MITSUBISHI MOTORS PassThru CAN Flash PassThru CAN Coding issThru CAN VIN Writing 17 of 46 a PassThru CAN User s Manual MITSUBISHI MOTORS 8 PassThru CAN Immobilizer 1 Menu screen The main screen appears Press PassThru CAN Immobilizer button a sm PassThru de MMC PassThru CAN Version 3 0 2 Please check the cable connectors and insulation for wear or damage DO NOT use queslionable cables Please make sure the Device fs connected to the vehicle Please turn the ignition Key ON The ENGINE should be OFF 2 Vehicle select screen The vehicle information table screen will appear Please select the correct vehicle type Press OK button on the screen Note You can also go back to the main screen by clicking return button ti
41. y Input correct VIN and retry yt Page 43 of 46 PassThru CAN User s Manual MITSUBISHI MOTORS Error Errordialog Cause Remedy j VIN Writing error VIN unmatched E Writing lt Possible cause gt Input VIN was written wrongfully and does not match written VIN Disconnection of harness while VIN writing ECU malfunction A VIN Writing error Current VIN didn t match input New lt Remedy gt Check harness PassThru device and ECU and try VIN writing from the beginning VIN Writing error writing function VIN Writing function lt Remedy gt Check if correct vehicle is applied for VIN Writing VIN Writing error VIN Writing lt Possible cause gt VIN Writing error ECU of the target vehicle does not support VIN Target ECU doesn t support Current This error resulted from other causes that are NRC SXX not described in this error list Error occurred during VIN Writing lt Remedy gt Restart VIN Writing from the beginning and retry If the same error occurs write down the NRC code in XX field of the error dialog and contact Mitsubishi Motors North America Inc 33 VIN Writing lt Possible cause gt aR VWPart file is damaged and information in the file could not be read out O File open error Error caused for parsing VVV Part file lt Remedy gt Reinstall correct VWPart file and retry 34 Teachin lt Possible cause gt T _Info tipart file is not found
42. y check Click OK button and execute Check Data list status While No 100 Teach in executing is Yes Plausibility check is ongoing Wait until the value turns No A If vehicle conditions are not met Pending is displayed When No 100 Teach in executing turns No Check the other data Check if value of data list items are as follows 101 Normal End Yes 102 Abnormal End No 103 Timeout error No 104 Abort conditions error No A If the above does not apply Plausibility check has not been performed correctly and start over from 1 Preparation Select Te achin command snd cick OK button to es Name Vako aout error Ne Page 25 of 46 Ei PassThru CAN User s Manual MITSUBISHI MOTORS 3 Shift fork Teach In Confirm datalist value of No 100 Teach in executing is No Select Shift fork Teach In Click OK button and execute the function Check Data list status While No 100 Teach in executing is Yes Shift fork Teach In is ongoing Wait until the value turns No A The function may take several minutes to complete Wait until the value changes to No A If vehicle conditions are not met Pending is displayed When No 100 Teach in executing turns No Check the other data Check if value of data list items are as follows
Download Pdf Manuals
Related Search