Manual - ETS
Contents
1. Note Model 7007 002 for laser powered probes includes additional indicators see page 22 for more information e Transmit yellow e Receive white Model 7007 001 EMSense card shown connectors may vary for Model 7007 002 www ets lindgren com Operation 21 INDICATOR LEDS FOR 7007 002 LASER ONLY LASER HOT red e Constant On e Flash LASER OK blue RECEIVE amber and TRANSMIT white POWER Green 22 Operation This is a warning that the laser is running too hot and the system should be checked Dirty fiber ends poor in line connections or damaged fiber optic cables are among the causes of a LASER HOT warning The system should be shut down as soon as possible and the cause of the additional heat investigated Continuing to run in a LASER HOT state may reduce the life of the laser This is an indication that the laser current is approaching 0 8 mA During the initialization phase of the startup process the probe receives more light once the probe is powered and communicating the power is rolled back to a normal level In these instances the user may see LASER HOT flash on this is normal operation This is the normal status when probe communication is established and laser light is provided to the probe for power These are illuminated during normal use e RECEIVE indicates the communication between the probe and the EMSense EMF Probe Plug in Card e TRANSMIT indicates the communicatio2. EMCenter Modular RF Platform Required The EMCenter Modular RF Platform is required for operation and is sold separately WETS LINDGREN EMCenter Front Panel al me res sus erect a cer rs unen Back Panel The EMCenter may be controlled from a computer using these software products e ETS Lindgren TILE Totally Integrated Laboratory Environment e ETS Lindgren EMQuest Data Acquisition and Analysis Software Other test automation software Contact ETS Lindgren for ordering information www ets lindgren com Introduction 11 This page intentionally left blank 12 Introduction www ets lindgren com 2 0 Maintenance CAUTION Before performing any maintenance follow the information provided in Safety Information on page vi WARNING Maintenance of the EMSense system is limited to external components such as cables or connectors If you have any questions concerning maintenance contact ETS Lindgren Customer Service WARRANTY Note For maintenance information for ETS Lindgren field probes see the EMC Field Probes User Manual included with the probe O www ets lindgren com Maintenance 13 Maintenance of Fiber Optics If Used Fiber optic connectors and cables can be damaged from airborne particles humidity and moisture oils from the human body and debris from the connectors they plug into Always handle connectors and cables with care
3. using the following guidelines CAUTION Before performing any maintenance disconnect the fiber optic cables from the unit and turn off power When disconnecting fiber optic cables apply the included dust caps to the ends to maintain their integrity Before connecting fiber optic cables clean the connector tips and in line connectors Before attaching in line connectors clean them with moisture free compressed air Failure to perform these tasks may result in damage to the fiber optic connectors or cables 14 Maintenance www ets lindgren com Replacement and Optional Parts Note ETS Lindgren may substitute a similar part or new part number with the same functionality for another part part number Contact ETS Lindgren for questions about part numbers and ordering parts Following are the part numbers for ordering replacement or optional parts for the EMSense EMF Probe Plug in Card Part Description Part Number EMSense EMF Probe 7007 001 EMSense EMF Probe Plug in Card Plug in Card for Battery Battery Operated Probes EMSense EMF Probe 7007 002 EMSense EMF Probe Plug in Card Plug in Card for Laser Laser Powered Probes www ets lindgren com Maintenance Service Procedures CONTACTING ETS LINDGREN Note Please see www ets lindgren com for a list of ETS Lindgren offices including phone and email contact information SENDING A COMPONENT FOR SERVICE 1 Contact ETS Lindgren Customer Service t
4. EXCEPT AS EXPRESSLY STATED ABOVE SELLER MAKES NO WARRANTY EXPRESS OR IMPLIED BY STATUTE OR OTHERWISE WHETHER OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE OR USE OR OTHERWISE ON THE PRODUCTS OR ON ANY PARTS OR LABOR FURNISHED DURING THE SALE DELIVERY OR SERVICING OF THE PRODUCTS THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF 34 Warranty www ets lindgren com Warranty coverage does not include any defect or performance deficiency including failure to conform to product descriptions or specifications which results in whole or in part from 1 negligent storage or handling of the product by Buyer its employees agents or contractors 2 failure of Buyer to prepare the site or provide an operating environmental condition in compliance with any applicable instructions or recommendations of Seller 3 absence of any product component or accessory recommended by Seller but omitted at Buyer s direction 4 any design specification or instruction furnished by Buyer its employees agents or contractors 5 any alteration of the product by persons other than Seller 6 combining Seller s product with any product furnished by others 7 combining incompatible products of Seller 8 interference with the radio frequency fields due to conditions or causes outside the product as furnished by Seller 9 improper or extraordinary use of the product or failure to comply with any applicable instruc
5. period to correct a warranty failure shall be warranted to the extent of the unexpired term of the warranty applicable to the repaired or replaced product www ets lindgren com Warranty 33 The warranty period shall commence on the date the product is delivered to Buyer however if Seller assembles the product or provides technical direction of such assembly the warranty period for such product shall commence on the date the assembly of the product is complete Notwithstanding the foregoing in the event that the assembly is delayed for a total of thirty 30 days or more from the date of delivery for any reason or reasons for which Seller is not responsible the warranty period for such product may at Seller s options commence on the thirtieth 30th day from the date such product is delivered to Buyer Buyer shall promptly inspect all products upon delivery No claims for shortages will be allowed unless shortages are reported to Seller in writing within ten 10 days after delivery No other claims against Seller will be allowed unless asserted in writing within thirty 30 days after delivery or assembly if the products are to be assembled by Seller or in the case of alleged breach of warranty within the applicable warranty period Warranty Exclusions Except as set forth in any applicable patent indemnity the foregoing warranties are exclusive and in lieu of all other warranties whether written oral express implied or statutory
6. BUYER EXCEED THE PURCHASE PRICE OF THE PRODUCT IN RESPECT OF WHICH DAMAGES ARE CLAIMED This agreement shall be construed in accordance with laws of the State of Texas In the event that any provision hereof shall violate any applicable statute ordinance or rule of law such provision shall be ineffective to the extent of such violation without invalidating any other provision hereof 36 Warranty www ets lindgren com Any controversy or claim arising out of or relating to the sale delivery non delivery servicing assembling use or loss of use of the products or any part thereof or for any charges or expenses in connection therewith shall be settled in Austin Texas by arbitration in accordance with the Rules of the American Arbitration Association and judgment upon the award rendered by the Arbitrator may be entered in either the Federal District Court for the Western District of Texas or the State District Court in Austin Texas all of the parties hereto consenting to personal jurisdiction of the venue of such court and hereby waive the right to demand a jury trial under any of these actions www ets lindgren com Warranty 37 This page intentionally left blank 38 Warranty www ets lindgren com Appendix B EC Declaration of Conformity ETS Lindgren Inc declares these products to be in conformity with the following standards following the provisions of EMC Directive 2004 108 EC Model 7007 001 EMSense EMF Probe Plug in Card Ba
7. Model 7007 001 Model 7007 002 EMSense EMF Probe Plug In Card User Manual Model 7007 001 EMSense card shown WETS LINDGREN An ESCO Technologies Company ETS Lindgren Inc reserves the right to make changes to any product described herein in order to improve function design or for any other reason Nothing contained herein shall constitute ETS Lindgren Inc assuming any liability whatsoever arising out of the application or use of any product or circuit described herein ETS Lindgren Inc does not convey any license under its patent rights or the rights of others O Copyright 2015 by ETS Lindgren Inc All Rights Reserved No part of this document may be copied by any means without written permission from ETS Lindgren Inc Trademarks used in this document The ETS Lindgren logo is a registered trademark and EMCenter EMSense TILE and EMQuest are trademarks of ETS Lindgren Inc Revision Record MANUAL EMSENSE Part 399347 Rev A on ptr f ome Initial Release March 2015 ji www ets lindgren com Table of Contents Notes Cautions and Warning scsseeescsseseeesscennseeeeees vi Safety IMM lios vi O INtoOdUCiION ci 9 Model 7007 001 EMSense for Battery Operated Probes cccccccccconncnnn 9 Model 7007 002 EMSense for Laser Powered Probes ccccsssseeeeeees 10 EMCenter Modular RF Platform Required cccseeeeeeeeeeeeeeeeeeeeeeeees 11 2 0 Maintenance oa 13 Mainte
8. OM failure Parity error For 7007 002 laser only Probe commands are not available unless the field probe is powered on To power on the probe send the Laser ON command r For more information on the r command see page 30 Received command is invalid www ets lindgren com EMSense Command Set 31 This page intentionally left blank 32 EMSense Command Set www ets lindgren com Appendix A Warranty Scope and Duration of Warranties Seller warrants to Buyer that the Products to be delivered hereunder will be 1 free from defects in material manufacturing workmanship and title and 2 conform to the Seller s applicable product descriptions and specifications if any contained in or attached to Seller s quotation If no product descriptions or specifications are contained in or attached to the quotation Seller s applicable product descriptions and specifications in effect on the date of shipment shall apply The criteria for all testing shall be Seller s applicable product specifications utilizing factory specified calibration and test procedures and instruments All product warranties except the warranty of title and all remedies for warranty failures are limited to three years Product Warranted Duration of Warranty Period Model 7007 001 EMSense 3 Years EMF Probe Plug in Card Battery Model 7007 002 EMSense 3 Years EMF Probe Plug in Card Laser Any product or part furnished to Buyer during the warranty
9. ead temperature in Txxxx lt LF gt Fahrenheit lt Null gt lt CR gt Send the ASCII null N lt LF gt character lt Null gt lt CR gt is a special command that can be used as the initial command to the field probe after it is turned on www ets lindgren com EMSense Command Set 29 Additional Commands for 7007 002 Laser Only Laser data interface 161 13 lt sr gt lt sn gt lt LF gt identification string e sr 10 character software revision sn 8 character serial number Laser OFF command o lt LF gt The laser and all LEDs except the green Power LED will turn off Laser ON command ir lt LF gt The blue Laser LED will illuminate immediately then the yellow Receive LED will illuminate a few seconds after indicating the probe is ready for operation The Laser ON command r should be the first command sent tc Read temperature in txxxx lt LF gt Centigrade Read temperature in txxxx lt LF gt Fahrenheit 30 EMSense Command Set www ets lindgren com Error Codes If an error occurs the probe will respond with one of the following strings These strings begin with a colon and end with a carriage return El E2 E3 E4 E5 E6 E7 E9 Communication error for example overflow Buffer full error too many characters contained between the start character and carriage return sequence Received command is invalid Received parameter is invalid Hardware error for example EEPR
10. ess hours After the warranty period service will be performed at Seller s prevailing service rates Subject to the availability of persomnel after hours service is available upon request at an additional charge Outside the contiguous 48 United States travel and per diem expenses when required shall be the responsibility of the Buyer or End User whichever is applicable regardless of the warranty period The remedies set forth herein are conditioned upon Buyer prompily notifying Seller within the applicable warranty period of any defect or non conformance and making the product available for correction The preceding paragraphs set forth Buyer s exclusive remedies and Seller s sole liability for claims based on failure of the products to meet any warranty whether the claim is in contract warranty tort including negligence and strict liability or otherwise and however instituted and upon the expiration of the applicable warranty period all such liability shall terminate INNO EVENT SHALL SELLER BE LIABLE TO BUYER FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR AS A RESULT OF THE SALE DELIVERY NON DELIVERY SERVICING ASSEMBLING USE OR LOSS OF USE OF THE PRODUCTS OR ANY PART THEREOF OR FOR ANY CHARGES OR EXPENSES OF ANY NATURE INCURRED WITHOUT SELLER S WRITTEN CONSENT DESPITE ANY NEGLIGENCE ON BEHALF OF THE SELLER IN NO EVENT SHALL SELLER S LIABILITIES UNDER ANY CLAIM MADE BY
11. h 7 numbered from left to right as you look at the back of the EMCenter 2 Remove the blank panel from the slot by removing the two screws at the top of the blank panel and the two screws at the bottom 3 Carefully insert the EMSense card into the slot of the EMCenter Tighten the four screws 4 Turn on the EMCenter The EMCenter will automatically detect the newly installed EMSense card 5 Place the field probe in the location where the field strength is to be measured 6 Connect the probe to the EMSense card 7 Connect the EMCenter to a personal computer using USB RS 232 Ethernet or IEEE optional 8 Plug the interlock into the connector on the back of the EMCenter The card installation is complete You can control EMSense through the EMCenter touchscreen with ETS Lindgren TILE Totally Integrated Laboratory Environment ETS Lindgren EMQuest Data Acquisition and Analysis Software and other test automation software packages Contact ETS Lindgren for additional information www ets lindgren com EMSense Plug In Card Installation 19 This page intentionally left blank 20 EMSense Plug In Card Installation www ets lindgren com 5 0 Operation CAUTION Before placing into operation follow the information provided in Safety Information on page vi CAUTION Prior to operation verify that the mains voltage is within the operating range of the equipment EMSense Connectors and Indicators CONNECTORS
12. light located on the front panel of the EMCenter will flash and then will illuminate steadily Note When the EMCenter is in standby mode touch the screen anywhere to reboot 3 Turn the power switch located on the back panel of the EMCenter to the off position 4 Remove the power cord from the power connector on the back panel of the EMCenter 5 Remove the interlock jack from the interlock connector on the back panel of the EMCenter 24 Operation www ets lindgren com Manual Control of EMSense Note For operational information for ETS Lindgren field probes see the EMC Field Probes User Manual included with the probe BATTERY OPERATED FIELD PROBE DATA FOR 7007 001 ONLY On the Home screen the status box to the right of the slot number for the installed EMSense card displays the isotropic field strength data EMPower 7002 001 AE A he l Off EMSwitch 7001 001 EMSwitch 7001 002 NC NC NC NC Info EMSense 7007 001 4 416 Vim Available EMControl 7006 001 0 0 99 9 cm Available Config Home Vim 4 Back X axis 3 712 Z axis 7 Info Probe model Sensor voltage Sensor temperature Zero Zero No Ranges 7 ows Config www ets lindgren com Operation 25 LASER POWERED FIELD PROBE DATA FOR 7007 002 ONLY On the Home screen the status box to the right of the slot number for the installed EMSense card displays the connected laser powered field probe 1 Press the status box and Ack will di
13. n between the EMCenter Modular RF Platform and the EMSense card This indicates that the EMCenter recognizes the EMSense card and is providing power www ets lindgren com Powering On and Off EMCenter Note For information on using the EMCenter touchscreen see the EMCenter Modular Test System User Manual POWER ON Note Verify all cards are installed correctly in the EMCenter 1 Plug the power cord from the mains inlet on the back panel of the EMCenter Modular RF Platform into a power outlet 2 Plug the interlock jack into the interlock connector on the back panel of the EMCenter 3 Turn the power switch located on the back panel of the EMCenter to the on position 4 Touch anywhere on the EMCenter screen It will take approximately 20 seconds to boot The Information screen will flash and then the Home screen will display MSwitch 7001 001 EMSWitel 001 021 EMSense 7007 001 No probe EMControl 7006 001 358 9 100 0 cm EMSense 7007 002 Standby Press to start 30 000 000 MHz RF OFF Sample EMCenter Home Screen www ets lindgren com Operation 23 POWER OFF 1 Press the Off button located on the EMCenter screen EMPower 7002 001 SAA Je EMSwitch 7001 001 NC NC EMSwitch 7001 021 Info Switch off system EMSense 7007 001 ES EMControl 7006 00 EMSense 7007 002 Standby Press to start 30 000 000 MHz RF OFF 2 Press OK to switch off the system The standby
14. nance of Fiber Optics If Used cccccccooccnnccnnccconoonccnnnnnnonanonos 14 Replacement and Optional Parts ccccccceeeeeeeeeeeeessseeeeeeeeeeeeeeeeaaas 15 SJ Procede S caicascte suc tencce sacennces ATE 16 Contacta Elo NN Oe et 16 Sending a Component for ServiC8 cccccccccccccccocnconnnnnnnnononnnonnnonnnnnnnas 16 3 0 Specifications ria a a a 17 PhysiGal SpeciiCatlons 0 ei A A LS 17 Environmental Specifications ccccocoonooccnonnnccnnnnnonononononononannnnnnnnnnnnnnnnos 17 4 0 EMSense Plug In Card Installation ccocoonnncnnnncnmmmm 19 5 0 ODera ON oasis it ic 21 EMSense Connectors and Indicators cooooncccnncccononnccnnncnnnnanccnnnnnnonanenos 21 CONC lisina duendes 21 Indicator LEDs for 7007 002 Laser Only o0coooocccccccnnccccccnnncccccnannncncnnns 22 Powering On and Off EMCenter ccccceeeeeeeeeceenessseseeeeeeeeeeeeeeeeaas 23 Power Da 23 POWER O Mit tose saat ace cca salem was one aa sane 24 Manual Control of EMSenNSe ccccccccccccccnncconononccnnnnonononnnnnnncnnnnanennnnnnnnnanonos 25 Battery Operated Field Probe Data For 7007 001 Only 25 Laser Powered Field Probe Data For 7007 002 Onlly 0008 26 6 0 EMSense Command Set scccccsssssssseeeeeeeeeeeensnneeeees 27 Information Transfer Protocols iaa aaa 27 Command SMUGCIUN Goe E E 27 Example 1 Request a Reading ccooocccccconnniccconococnnnnncnnnncnncnn
15. nncnnoos 27 Example 2 Request a Reading cooocccccconcncccconononnnonaronnnonncnnnnonnnos 27 Commands for 7007 001 and 7007 002 cccccceeeeeeeeeeeeeeeeeeeeeeeeeeeens 28 www ets lindgren com Additional Commands for 7007 002 Laser Only 0oooncccccnnncccccccccnonnnannnnnnnnns 30 A A Eo PE 31 Appendix A Warfare o 33 Scope and Duration of Warranties cccccccnccccccnnncocononannnnnnnnnnnnnnnnnnnnnnnnns 33 Warranty EXCIUSIONS cae 34 Buyers Remedies irn ssenaeee Macnee eine eee IE MIRRA 35 Appendix B EC Declaration of Conformity 008 39 IV www ets lindgren com This page intentionally left blank www ets lindgren com Notes Cautions and Warnings Note Denotes helpful information intended to provide tips for better use of the product Caution Denotes a hazard Failure to follow instructions could result in minor personal injury and or property damage Included text gives proper procedures Warning Denotes a hazard Failure to follow instructions could result in SEVERE personal injury and or property damage Included text gives proper procedures Safety Information gt Class 1M LASER HAZARD Laser power up to 150 mW at 830 nm may be accessible at the fiber connector of the laser However the laser beam itself is not hazardous as the interlock ensures that the exposure time will be less than 30 ms OR AN High Voltage Indicates presence of hazardous v
16. o obtain a Service Request Order SRO 2 Briefly describe the problem in writing Give details regarding the observed symptom s or error codes and whether the problem is constant or intermittent in nature Please include the date s the service representative you spoke with and the nature of the conversation Include the serial number of the item being returned 3 Package the system or component carefully If possible use the original packing materials or carrying case to return a system or system component to ETS Lindgren 16 Maintenance www ets lindgren com 3 0 Specifications Note For ETS Lindgren field probe specifications see the EMC Field Probes User Manual included with the probe O Physical Specifications Environmental Specifications Temperature Range 0 C to 35 C 32 F to 95 F Relative Humidity 10 to 90 non condensing www ets lindgren com Specifications 17 This page intentionally left blank 18 Specifications www ets lindgren com 4 0 EMSense Plug In Card Installation CAUTION Before connecting any components follow the information provided in Safety Information on page vi CAUTION The EMSense card is designed to be used ONLY with the EMCenter Do not use the card in combination with any other system 1 Determine in which empty slot in the EMCenter Modular RF Platform you want to install the EMSense EMF Probe Controller Plug in Card You may use slots 1 throug
17. oltage Unsafe practice could result in severe personal injury or death www ets lindgren com Protective Earth Ground Safety Ground Indicates protective earth terminal You should provide uninterruptible safety earth ground from the main power source to the product input wiring terminals power cord or supplied power cord set www ets lindgren com vil This page intentionally left blank Vill www ets lindgren com 1 0 Introduction The ETS Lindgren Model 7007 001 EMSense EMF Probe Plug in Card is designed for use with the following ETS Lindgren battery operated field probes the Model 7007 002 EMSense card is designed for use with the following ETS Lindgren laser powered field probes sold separately Each EMSense card can support one ETS Lindgren probe O Model 7007 001 EMSense for Battery Operated Probes Note Contact ETS Lindgren for information on ordering probes For complete information on ETS Lindgren field probes see the EMC Field Probes User Manual included with the probe HI 6022 HI 6053 HI 6005 www ets lindgren com Introduction Model 7007 002 EMSense for Laser Powered Probes HI 6122 HI 6153 HI 6105 EMSense is fully supported by ETS Lindgren TILE Totally Integrated Laboratory Environment ETS Lindgren EMQuest Data Acquisition and Analysis Software and other test automation software packages Contact ETS Lindgren for additional information 10 Introduction www ets lindgren com
18. om the EMSense card in slot 2 using the LAN or optional GPIB interface www ets lindgren com EMSense Command Set 27 Commands for 7007 001 and 7007 002 Read probe converter Bxx Xxx lt LF gt voltage Read probe converter B64N lt LF gt voltage in hexadecimal e N safe operating level format e F fail level Voltage reported as 0 64 64 corresponds to 100 The BP command is provided for backward compatibility and should not be used to monitor the converter voltage which always responds with B64N lt LF gt Read probe data Dx xxxyy yyZZ2Z Z2B lt LF gt e XXXX YYYY ZZZZ 4 digit axis values with floating decimal point e B battery flag N or F B battery flag N or F D5 Read probe data Dx XXXyy yyzzz zcccc B lt LF gt XXXX YYYY ZZZZ 4 digit axis values with floating decimal point cccc composite field value with floating decimal point 28 EMSense Command Set www ets lindgren com Identification command 16105 lt sr gt lt sn gt lt cd gt B lt LF gt e sr 10 character software revision sn 8 character serial number cd 8 character calibration date B battery flag N or F The Identification command I may also be used as the first command sent The command will turn on the laser Once communication between the probe and the HI 6113 is established the return string will be sent Subsequent I commands immediately send the return string TC Read temperature in Txxxx lt LF gt Centigrade R
19. splay EMP ower 7002 001 EMSwitch 7001 001 EMSwitch 7001 021 EMSense 7007 001 No probe EMControl 7006 001 83 4 175 0 cm EMSense 7007 002 Verifying Press Ack EMGen 7003 001 2 500 000 000 GHz RF OFF 2 Press Ack and LASER ON will display on the front panel 3 Press the status box again to display the data for the probe 0 453 V m X axis 0 224 Y axis 0 302 Z axis 0 252 Probe model 6105 Sensor voltage 3 717 V Sensor temperature 240C Laser current 577 mA Laser temperature 28 8 c Laser is on 26 Operation www ets lindgren com 6 0 EMSense Command Set See EMSense Commands on page 28 for the commands that can be used with the EMSense EMF Probe Plug in Card Information Transfer Protocol COMMAND STRUCTURE See the following pages for detailed information regarding the command structure to the field probe When the probe completes the command it responds with a string consisting of e A start character e The command letter e Data if required e lt LF gt a line feed If the command does not require the probe to return any data the probe simply responds with the start character then the command letter and a carriage return If an error occurs the probe responds with an error code EXAMPLE 1 REQUEST A READING To request a reading from the EMSense card in slot 1 using the LAN or optional GPIB interface 2 2S EXAMPLE 2 REQUEST A READING To request a reading fr
20. tions or recommendations of Seller including maintenance calibration and cleaning procedures and intervals or 10 acts of God acts of civil or military authority fires floods strikes or other labor disturbances war riot or any other causes beyond the reasonable control of Seller This warranty does not include 1 batteries 2 cables 3 gasket 4 fingerstock or any item that is designed to be consumable Seller does not warranty products of others which are not included in Seller s published price lists Buyer s Remedies If Seller determines that any product fails to meet any warranty during the applicable warranty period Seller shall correct any such failure by either at its option repairing adjusting or replacing without charge to Buyer any defective or nonconforming product or part or parts of the product Seller shall have the option to furnish either new or exchange replacement parts or assemblies Warranty service shall be performed at the Seller s factory or the Buyer s site at the sole discretion of the Seller Within the warranty period the Buyer shall be responsible for all transportation to the Seller s factory and the Seller shall be responsible for transportation of goods to the Buyer s site www ets lindgren com Warranty 35 Within the contiguous 48 United States warranty service performed during the applicable warranty period will be performed without charge to Buyer during Seller s normal busin
21. ttery Model 7007 002 EMSense EMF Probe Plug in Card Laser Emission EN 61326 1 2006 Class B Electrical equipment for measurement control and laboratory use Immunity EN 61326 1 2006 Industrial level performance criteria A Electrical equipment for measurement control and laboratory use Technical Construction Files are available upon request www ets lindgren com EC Declaration of Conformity 39
Download Pdf Manuals
Related Search