Z3-MVE-02
Contents
1. Power on the Z3 MVE 02 Wait one minute or until LED Status 1 on the unit lights up Connect the Ethernet cable from the Z3 MVE 02 unit directly to the PC Disable all wireless and local area connections For a client PC to access the Z3 MVE 02 factory default settings set the IP address of the PC to 192 168 XX XX See 5 1 PC Setup Open Firefox or Internet Explorer 8 or above as your web browser Type the IP address of the Z3 MVE 02 in your web browser http 192 168 XX XX and the Z3 MVE 02 Encoder web configuration menu will appear Configure the Z3 MVE 02 with your desired settings Press Start Encoder on the Encoder Control menu Status 2 LD should now be lit and the title in the top right of the browser should now say MVE 02 Encoder as pictured here in the example L Technology uc Z3 MVE 02 Encoder Firmware version 1 04 15 UPDATE device name MVE 02 set name set pass logout Operating Mode Encoder v Encoder Setup Output Setup Video Source HDMI X Output Interface ASl Ethernet CBR Audio Source Channels 1 2 X Output Format MPEG 2TS X Audio Codec AAC LC ADTS DestIP Address 192 168 0 7 Audio Bit Rate 128 kbits Dest Port 8888 Video Resolution Follow Input TS Bitrate 12000 Rate Control CBR ASI PCR Interval Video Bit Rate 8000k PID Audio Video PCR Video Profile High Local IP Setup Gop Size 60 Frames Local IP Address 192 168 3 93 Vide2. 8888 where is the IP Address of your personal PC 5 Press play 6 If the original video is interlaced the video can be deinterlaced as follows a On the Video Menu choose Deinterlace and choose an option other than Disable If your output format is real time transport protocol please follow the steps below 7 2 REAL TIME TRANSPORT PROTOCOL 1 Open VLC Media Player 2 On the Media menu choose Open File Cntrl O 3 Under the Media Files category choose All Files 4 Choose the SDP file provided by Z3 Technology Note If you do not have the SDP file please to refer to your Z3 Server user account and download the file 5 If the original video is interlaced the video can be deinterlaced as follows a On the Video Menu choose Deinterlace and choose an option other than Disable 8 0 DYNAMIC BIT RATE amp FRAME RATE CHANGE The dynamic bit rate and frame rate control will take effect if you change the following parameters Video Bit Rate Frame Decimation After the Video Bit Rate and Frame Decimation rate have been configured to your preferred settings hit the Start Encoder or Restart Encoder button The web page will respond with Status Changed rate The video stream will continue uninterrupted with the new parameter 13 Z3 Technology LLC 100 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07 V1 04 16 E
3. V1 04 16 E Technology 9 2 SYSTEM MENU CONTROL T Transport RTP TS F Frame Rate Divider 1 2 3 4 5 R Resolution Follow Input Custom 720p 1080i D1 NTSC D1 PAL 4 CIF 2 CIF CIF QCIF B Bitrate Custom 50k 64k 128k 250k 500k 750k 1500k 2000k 2500k 3000k 3500k 4000k 12000k P H 264 Profile Baseline Main High Fast 15 Frames 30 Frames 60 Frames 120 Frames 240 Frames Y H 264 QP Range H 264 QP range format min init max lt minIntra gt maxlntra Example 5 28 48 0 40 means Inter frame QP ranges from 5 to 48 Initial QP of 28 Intra frame QP ranges from 0 to 40 Minimum allowed is 0 maximum is 51 C Rate Control Mode CBR VBR Storage E Scan Mode Interlaced Progressive D Delay Limit 150ms 300ms 500ms 1000ms 2000ms 10 0 UPDATING FIRMWARE 10 1 WEB PAGE Locate the UPD z3 mve02 v1 04 15 img file on your Z3 Server user account Save the file on your PC where it can easily be found Follow steps 1 through 7 in section 6 2 WEB SERVER ENCODER On the web menu next to Firmware Version 1 0 4 hit the Update button Hit Browse to find the saved img file on your PC Hit Upload amp Update Power off unit 15 Z3 Technology LLC 100 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07 V1 04 16 73 Technology Power cycle system for clean boot and system should be updated 10 2 SD CARD Locate the UPD z3 m
4. 100 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07 V1 04 16 E Technology 6 6 IP SETTINGS DECODER 1 Once the decoder has stopped type in your desired IP settings 2 Hit Save User to save your desired settings 3 Power cycle the Z3 MVPR 01 4 The new IP settings will now take effect 6 7 DECODER CONFIGURATION OPTIONS Input Selection Input Interface Ethernet DVB ASI RTP MPEG 2 TS Decoder Setup Video Codec H 264 Audio Codec AAC POM None Output Setup Video Frame Rate 50Hz 60Hz 7 0 STREAMING OPERATION After connecting your video audio source and configuring the Z3 MVE 02 Encoder hit Start Encoder so the status below says Status Running If you are using the serial command instead type S to start streaming The way to set up VLC as your stream receiver on your PC differs depending on the format of your output stream If your output format is transport stream please follow the steps below 12 Z3 Technology LLC 100 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07 V1 04 16 y r LLC TRANSPORT STREAM 4 Open VLC Media Player 2 Media menu choose Open Network Stream Cntrl N 3 If using VLC version 1 0 X a On the Protocol menu choose UDP b Type in the static IP address of your personal PC c Change the Port Address to 8888 4 lf using VLC version 1 1 X a Enter the network URL as follows
5. E Technology Z Technology User s Manual HD Multi format Video Encoder Model Name Z3 MVE 02 Z3 Technology LLC Multi format Video Encoder MVE 02 Status 2 0 Version 1 04 16 July 17 2012 Before attempting to connect or operate this product please read these instructions carefully and save the manual for future use Z Technology Tel 1 402 323 0702 www z3technology com sales z3technology com 1 Z3 Technology LLC 100 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07 V1 04 16 E Technology Revision History Version Date Change Note Author 1 1 0 1 5 10 Original System AC 1 1 1 5 6 10 Updated System AC 1 1 2 5 7 10 Made correction AC 1 1 3 6 25 10 Added MPEG 2 TS and HTTP Option AC 1 1 4 11 11 10 Added Web Server Control of System CH 1 1 5 11 17 10 Updated VLC Instructions CH 1 1 6 5 17 11 Updated Encoder Configuration Options CH 1 1 7 5 20 11 Updated Web Server Image Manual Layout CH 1 2 2 6 13 11 Updated Features and synchronized document with SW version CH 1 0 4 1 27 12 Updated Images Layout TOC Section 8 Section 10 CH 1 0 4 1 2 7 12 Updated Screen Encode and decode Screen Shots Highlight Nptes SC 1 0 4 2 2 13 12 Added Troubleshooting Section CH 1 04 15 6 8 12 Updated SW Version SC 1 04 16 7 17 12 Address Update NS 2 Z3 Technology LLC 100 8 ST STE 250 Lincoln NE 68508 1369
6. Status 1 2 Audio Composite IN ASI SDI Out IN Z3 MVE 02 A d e 5 Copyright c 2010 2 Z3 Technology LLC s 7 http www z3technology com FN Gy 7 4 Io B jJ NJ Component Y Component Pb Component Pr HDMI DVI IN 12VDC Ethernet Power IN 1 Status 1 LED 2 Status 2 LED 3 USB Interface 4 SD Card Interface 5 Power Switch 6 Analog Audio In L 7 Composite In 8 ASI SDI Out 9 SDI ASI In 10 RS 232 Port 11 Audio In R 12 Component Y 13 Component Pb 14 Component Pr 15 HDMI DVI In 16 VGA In 17 Ethernet 18 12V Power 7 Z3 Technology LLC 100 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07 V1 04 16 E Technology 6 0 SYSTEM CONNECTIONS The System can be controlled via the Web Server on the Z3 MVE 02 It can also be controlled via the serial port 6 1 PC SETUP Initially the simplest way to setup the networked PC to communicate with the Z3 MVE 02 is to put the PC on the same subnet as the Z3 MVE 02 The IP address of the Z3 MVE 02 can be found on the bottom side of the Z3 MVE 02 The Windows PC can be setup on the same subnet by using these parameters Internet Protocol TCP IP Properties Microsoft Windows users p S General E 1 Goto the Start Menu and select You can get IP settings assigned automat
7. Technology 9 0 APPENDIX A SERIAL CONTROL Note Please only use the serial control if you are experiencing difficulties with the Web Server Plug in DB 9 serial cable from the Z3 MVE 02 to your PC Setup Teraterm on the PC for 115k 8 1 1ms char 50ms line Connect to the proper COM port Connect the Power to the Z3 MVE 02 Power on the Z3 MVE 02 Output should come immediately to the Teraterm console 91 TERMINAL OUTPUT Z3 Technology LLC MVE 01 v07 H 264 Streaming Encoder Current Change video input COMPONENT A Change audio aac N Change network address 225 1 2 3 T Change transport RTP F Change framerate divider 1 R Change resolution 10801 Change size 60 Change video bitrate 9000k P Change H 264 Profile high Y Change H 264 QP range 5 28 51 0 40 C Change rate control mode CBR E Change scan mode Interlaced D Change delay limit ms 500 1 Set defaults for D1 streaming 2 Set defaults for 720p streaming 3 Set defaults for 10801 streaming S Start streaming X eXit to prompt W Write config to flash Enter option 14 Z3 Technology LLC 100 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07
8. SPORT PRO TOC OD ote 13 8 0 DYNAMIC BIT RATE amp FRAME RATE 2442224 1 13 VD APPENDIX A SERIAL CONTROL Gs 14 TERMINALOUTPUT 14 92 SYSTEM MENU CONTROL Riesa Ope bite 15 10 0 UPDATING 15 10 1 15 16 11 0 TROUBLESHOOTING 16 3 Z3 Technology LLC 100 N 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07 V1 04 16 E Technology 1 0 GENERAL INFORMATION 1 1 PREFACE The Z3 MVE 02 Multi Format Video Encoder is a compact 114mm x 203mm system that supports H 264 High Profile encode up to 1080p at 30 frames per second This solution works in multiple applications such as low cost broadcast encoders low bandwidth video security satellite uplink remote monitoring and industrial applications The Z3 MVE 02 provides immediate access to multi format HD video integrated system peripherals and production qualified codecs The Z3 MVE 02 offers multi format multi channel HD video up to 1080p30 The Z3 MVE 02 features HD performance compact size and low latency while having less power consumption than a PC based encoder platform 2 0 ABOUT THE MANUAL Before attempting to
9. U S A 1 402 323 07 V1 04 16 E Technology CONTENTS 1 0 GENERAL INFORMATION 2 4 1I PREFACE RT ease 4 20 ABOUT DHENDANLUAL uicina rere te ee eet 4 LIS 4 INCLUDED NU d rc Y 4 3 2 OPTIONAL ACCESSORIES inka n sias a TES a aE E ASEAS EESE Ean ES 5 4 0 FEATURES PP 6 5 0 OPERATING CONTROLS reiron i Ea T E EIE A E EE E E 7 6 0 SYSTEM CONNECTIONS Gites 8 2 E o est A 8 52 WEB SER VER ENCODER ooa A E 8 53 L COCALIP SETTINGS ENCODER s E 9 6 4 ENCODER CONFIGURATION OPTIONS 10 63 WEB SERVER DECODPBB 11 6 6 IP SEFTINGS DB OCODEBBR 12 6 7 cis e Md tupra 12 STREAMING DPERATION iiid te oU rbi ido Ee stein ANKESES daei 12 LL TRANSPORT Pc c 13 74 REAL TIME TRAN
10. connect or operate this product please read these instructions carefully and save this manual for future use 3 0 PARTSLIST 3 1 INCLUDED PARTS Power Supply BNC to RCA Cable x3 RCA to RCA Cable E Technology 3 2 OPTIONAL ACCESSORIES Serial Cable Ethernet Cable HDMI Cable 5 Z3 Technology LLC 100 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07 V1 04 16 E Technology 4 0 FEATURES The Z3 MVE 02 is a high definition low cost network enabled media encoder with the following features HD resolutions up to 1920x1080 including 1080i 1080p30 and 720p Supported video includes H 264 MPEG 4 and MPEG 2 Standard Definition encoding for ISDB T DVB H etc Low latency encode mode Video Inputs Composite Component HD SDI DVI HDMI Optional ASI input Input video re sizer supports 1 2 2 3 and 3 4 of standard resolutions Output Interfaces Ethernet and ASI Optional HD SDI output Outputs RTP or MPEG 2 Transport Stream USB interface for mass storage devices or other peripherals SD Card interface for local storage and firmware updates RS232 serial port for configuration and control Web based configuration software 6 Z3 Technology LLC 100 N 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07 V1 04 16 73 Technology LLC 5 0 CONTROLS FRONT VIEW Z3 Technology LLC Multi format Video Encoder MVE 02
11. ernet ASI ASI Ethernet Output Format RTP MPEG 2 TS 10 Z3 Technology LLC 100 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07 V1 04 16 E Technology Dest IP Address Dest Port PID Audio Video PCR 192 168 X XX Use IP address of your PC 8888 Local IP Setup Local IP Address 192 168 Local Netmask 255 255 0 0 Default Gateway 192 168 0 1 6 5 WEB SERVER DECODER 1 Stop the Encoder by pressing Stop Encoder on the server 2 Press the Decoder Button next to Operating Mode to change the operating mode to Decoder The title in the top right of the browser should now say MVE 02 Decoder as pictured here in the example v Lim Input Selection Input Interface Ethernet Input Format IP Port 225 1 2 3 8888 Video Codec 264 Audio Codec MVE Flag Decoder Control Stop Decoder Start Decoder Status User presets 11 73 02 Decoder Firmware version 1 04 15 UPDATE device name MVE 02 set name set pass logout Operating Mode Decoder Output Setup Output Interface SDI Video Frame Rate 60 Hz Local IP Setup LocalIP Address 192 168 3 93 LocalNetmask 255 255 0 0 Default Gateway 192 168 0 1 Load Factory Default Settings Load Factory Load User Settings Load User Save User Settings Save User Z3 Technology LLC
12. ically if your network supports Control Panel this capability Otherwise you need to ask your network administrator for 2 Click on Network and Sharing Center the appropriate IP settings 3 Click on View Status 4 Click on Properties Obtain an IP address automatically 5 Click Internet Protocol TCP IP and 3 click Properties Use the following IP address 6 In the Internet Protocol TCP IP Properties window select Use the following IP address if not already selected and specify the IP address you wish to use While entering this Default gateway 192 168 0 data you ll also need to specify the subnet mask and default gateway IP address Subnet mask Linux users 9 Use the following DNS server addresses Preferred DNS server The below information is for how to specify and adjust your network settings through the command prompt Changing your network settings will require root access 1 Getto the command prompt Meter 2 Move to the etc sysconfig network directory 3 Editthe interfaces file and adjust your network settings in this file Alternate DNS server 8 Z3 Technology LLC 100 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07 V1 04 16 E Technology 6 2 WEB SERVER ENCODER Note If you use unicast on the encoder you must also use unicast on the VLC receiver If you use multicast on the encoder you must also use multicast on the VLC receiver
13. o burst size 300ms v Local Netmask 255 255 0 0 Video Codec 264 Default Gateway 192 168 0 1 Frame Decimation None Encoder Control Stop Encoder Start Encoder Status User presets Load Factory Default Settings Load Factory Load User Settings Load User Save User Settings Save User Z3 Technology LLC 100 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07 V1 04 16 E Technology 6 3 LOCALIP SETTINGS ENCODER e Inthe Local IP Settings Section type in your desired Local IP settings e Save User to save your desired settings e Power cycle the Z3 MVE 02 The new settings will now take effect 6 4 ENCODER CONFIGURATION OPTIONS Encoder Setup Audio Source Analog Jacks Channels 1 2 Channels 3 4 Channels 5 6 Channels 7 8 Audio Codec AAC LC ADTS AAC LC LATM PCM AC 3 Passthru None Video Resolution Follow Input 1080i 1920x1080 3 4 1080i 1440x1080 XGA 1280x1024 720p 1280x720 4 5 720p 1024x720 D1 NTSC 720x480 D1 PAL 720x576 4 CIF 704x576 VGA 640x480 2 352x576 CIF 352x288 SIF 352x240 QVGA 320x240 WQVGA 320x180 Rate Control CBR VBR Video Profile Baseline Main High 15 Frames 30 Frames 60 Frames 120 Frames 240 Frames Video Burst Size 150ms 200ms 300ms 400ms 500ms 600ms 800ms 1000ms 1200ms 1400ms 1600ms 1800ms 2000ms Video Codec H 264 MPEG 2 Output Setup Output Interface Eth
14. ve02 v1 04 15 img file on your Z3 Server user account Place SD card into computer Open the zwriter exe windows program provided by Z3 Select the UPD z3 mve02 v1 04 15 img file Select correct location for your SD card Do NOT make mistake on this item This will cause wherever you are writing to be overwritten There is no recovery once you hit Write Device Eject SD card from computer Place in SD card socket of APP board Power on system with terminal output connected to PC You will see the system updating the flash Once complete the system will boot Power off unit Remove SD card Power cycle system for clean boot and system should be updated 11 0 TROUBLESHOOTING No video is usually caused by networking issues First check IP address Netmask Ping from Z3 MVE 02 and ping 23 02 from PC Use direct connection from Z3 MVE 02 to PC without router customer network Once video connection is established then add in customer specific network equipment Second check to make sure firewalls are turned off o Third check video source Verify video source is outputting compatible analog video o Fourth verify PC is fast enough and has enough DDR to decode compressed video o Fifth verify VLC version is 1 1x or later No SDP file o Check your Z3 server account 16 Z3 Technology LLC 100 8 ST STE 250 Lincoln NE 68508 1369 U S A 1 402 323 07 V1 04 16
Download Pdf Manuals
Related Search
Z3 MVE 02