User`s Manual
Contents
1. Optoma Projector Ceiling Pole Mount Model OCM815W OCM815B Optoma User Operation Guide 120154 PV Nie e Thank you for purchasing the Universal Projector Ceiling Mount This bracket is suitable for most projectors up to a load of 15kg 33lbs e To ensure correct usage please read this instruction manual thoroughly Keep this manual for future reference e BRACKETS SHOULD BE MOUNTED ONLY BY A QUALIFIED INSTALLER e User will be responsible for any injuries and damages that may arise from improper installation and handing of Universal Ceiling Mounting Kit e Ensure all mounting screws are appropriately positioned and properly tighten fastened e Installers are to ensure customer s safety during installtion e We reserve the right to amend or undertake any necessary changes without prior notice N WARNING This symbol indicates incorrect handling Ignoring this symbol can result in the possibility of personal injury or even death N CAUTION This symbol indicates incorrect handling Ignoring this symbol can result in the possibility of personal injury and physical damage ZN Caution This symbol indicates additional cautions including warnings general Forbidden general This symbol indicates forbidden actions o Required This symbol indicates required actions general Optoma ALIOR Net Weight 2 52 kg 5 56 Ibs Dimension 420 x 200 x 12. 20 mm 16 5 x 7 9 x 4 7 Extendable Length Min to Max Min 576mm Max 826mm Min 22 7 Max 32 5 Load Capacity 15 kg 33 Ibs OOOO es 3 Specifications are subject to changes without notice User Operation Guide N AR Assembling without the correct use of bolts and screws at designated points may result in injury and damage to properties or the unit collapsing from its installed position Should a malfuction occur disconnect the power from the main socket and surround the area with ropes to prevent others from getting near it Check and ensure the ceiling where you install can support the weight or the projector and ceiling mounting All Ceiling Mounting Brackets are to be firmly secured so the unit will not drop off its installed position HE S N fi Steps should be taken to ensure the ceiling and installed unit can withstand K external forces like earthguakes vibrations etc U S s W Do not remove any bolts and screws from the Ceiling Mounting Brackets or do any changes to the Ceiling Mounting Brackets ih Do not install near an air conditioner o Z x a Do not install at place where there are excessive dust and smoke as fire could arise from these sources E p JJ Optoma Keep the room well ve
3. Nylock Nuts as shown Parts Required x3 N1 b x3 N2 p N1 x6 N3 7 4e Upper Pole 1 2 Assemble the Lower Pole by inserting it onto Upper Pole adjust to your desired length and secure with M8x55 Socket Cap Screws Washers and M8 Nylock Nuts Parts Required x1 N1 x1 N2 x2 N3 x4 d Lower Pole Oval slits at the bottom 2 Attaching the Universal Head Assembly to the Projector M8x15 Socket Cap Screw Short Pole Cross Recessed Screws A I M8x65 Socket Cap Screw NS M5x10 Socket Button Screw gt 4 Square Nut e P lt gt 1mm 2mm amm 2 gt lt Washers Bottom Spacer Optoma 2A Attaching the Universal Head Assembly to the projector 2A 1 Loosen the M5x10mm Socket Button Cap Screws using the 3mm Allen key until you can slide the extension brackets freely as shown Universal Head A Assembly Extension Bracket 100mm 3mm Allen Key M5x10mm Socket Button Cap Screw 2A 2 Place projector s Flush Mount Assembly over the projector and align the centre of the Flush Mount with the projector s approximate Centre of Gravity __ Centre of Universal Head Assembly This surface to be ap proximate parallel to the Projector 8 Specifications are subject to changes without notice User Operation Guide 2A 3 Place the Bottom Spacers in between the Extension Brackets and the Projector and align the mounting holes as sh
4. Universal Head Assembly FM p PS FE a se Upper Pole Lower Pole AG 3 3 Installtion completed Please consult our authorized service personnel when you encounter any problem during installation We are not liable for any damage or injury caused by mishandling or improper operation 11 ptoma Due to continuing product development the manufacturer reserves the right to alter specifications without notice Published 24 01 2014 Www optoma com
5. ntilated to prevent room temperature rising and possibilities resulting in fire 100mm 3 94 or more lt 100mm 3 94 or more Do not install in location where room temperature and humidity are excessively high to prevent fire To prevent fire avoid contact with water N Do not apply unnecessary stress or load on the installed unit 5 Specifications are subject to changes without notice M4x15 Cross Recessed A S 4 pcs Ceiling Mount 1 4 pcs Screw C 4 pcs Screw 4 pcs Screw 4 pcs Screw Lower Pole 1 M5x25 Cross Recessed apes 4 pcs Screw M6x15 Cross Recessed 4 pcs Screw Universal Head Assembly M6x20 Cross Recessed dees Screw M6x25 Cross Recessed 4 pcs Screw 1mm Washer 4 pcs 4mm Washer 3mm Allen Key Bottom Spacer 6mm Allen Key M8x55 Socket Cap Screw Tools Required for mount assembly f 1 1x Star Philips Screw Driver 2 1x 13mm Spanner M3x15 Cross Recessed Screw M3x20 Cross Recessed Screw M3 Flat Washer M4x6 Cross Recessed Screw M5x10 Socket Button Screw Square Nut Extension Bracket 50mm User Operation Guide N 4 A ON D 1 Assembling the Ceiling Mount Plate to the Upper and Lower Pole Ceiling Mount plate 1 1 Assemble the Upper Pole using M8x55 Socket Cap Screws Washers and M8
6. own below U anoi Mounting Hole NOTE N a If the mounting holes on your projector 3 Extension Bracket are recessed you may need to use the additional spacers supplied in the parts bag Please select the appropriate spacers according to the design of your projector Recessed Mounting Hole Bottom Spacer Spacer M5x10mm Note 2 If you cannot align the 100mm Extension Bracket to the mounting hole on your projector you may need to use the additional 50mm Extension Brackets shown in the diagram on the right Extension Bracket Square Nut Bottom ae User Operation Guide 2A 4 Select the correct Mounting Screws from the Parts bag and firmly screw the Universal Head Assembly onto your Projector Once this is done the Projector with Universal Head Assembly is ready to be mounted onto the Ceiling Plate Pole Mounting Screw Bottom Universal Head Assembly Completed Universal Head Assembly with Projector User Operation Guide 3 Installing the Ceiling Pole Mount 3 1 3 2 Install the Ceiling Mount Plate to the Attach the Universal Head Assembly ceiling with Lag Bolts and Washers with the projector by inserting M8x55 not included in the package as shown Socket Cap Screw with Washers below through the slot holes and secure with M8 Nylock Nut as shown Ceiling Plate D gl Lower Pole Sun a L T ot Lag Bolts and Washers Not Included in the Package
Download Pdf Manuals
Related Search