Prener-LC PREAMP USER`S MANUAL
Contents
1. Prener LC PREAMP USER S MANUAL Functions 4Band EQ amp LCD Digital Processing Tuner e QO O n bO gt O lt a Of N Digital Processing Tuner M 2 y A N AUTO CHROMA VF JS Prener Lc ape we SS i ee O lt 1 Tuner LED Display 2 Tuner LCD Display 6 Presence 7 Note 3 Bass 8 Low Batt Low Battery LED Light 4 Middle 9 Volume Knob 5 Treble 10 Power on off Button 1 Oo o amp GOU Bass EQ TONE CONTROL for bass tones Middle EQ TONE CONTROL for middle tones Treble EQ TONE CONTROL for high tones Presence EQ TONE CONTROL for very high tones The BASS MIDDLE TREBLE and PRESENCE controls are a 4 band equalizer for controlling tone The BASS TREBLE and PRESENCE tone controls are normal boost cut shelving controls The MIDDLE midrange tone control is a normal boost cut tone filter The center detent on these tone controls yields a flat tone response 12 boosts the tone 12 cuts the tone 7 Note Button 8 Low Batt Low Battery LED Light The LED will light when the battery has lost power Replace the battery when this light is on This LED light will flash when a cable is connected to the output jack of the pickup system This shows the battery is good 9 Volume Knob The VOLUME controls the output2. nd so on For flat notes for example Bb B flat use A For Eb E flat use D Specification Features 4Band EQ amp LCD Tuner Input Impedance 2 2MQ Frequency Response 20Hz 20KHz Control Range Bass 12dB at 60Hz Middle 12dB at 500Hz Treble 12dB at 3KHz Presence 12dB at 10KHz Power Supply 9V Alkaline Battery Battery Life Only EQ Tuner off Over 700Hours Tuner on with signal Over 300Hours Tuner Function Mode Auto amp Manual Tuning Mode Tuning Note Chromatic Mode Guitar Mode Function LCD Tuner System Chromatic amp Guitar or Bass tuning mode Balance amp Unbalance Output Jack Pick up Piezo ceramic pick up Battery Box XLR Combo Battery Box Dimension W 58mm X H 98 mm 2 3 x 3 8 Caution The jack should be pluged for proper Preamp working TUNER will works regardless pluging jack There is no output sound please check if tuner or mute is turned on When LCD screen is dim or no display please check battery life To prevent battery loss please unplug jack when preamp is not in use Do not disassemble for repair Return to your dealer for service or repair Do not use too much force when operating the control belat BELCAT Co Ltd Tel 86 752 355 7545 Fax 86 752 355 2460 Email belcat belcat com Internet www belcat com RoHS X ce This product complies with the RoHS directive E INSTALLATION MANUAL 1 Cut out the h
3. of guitar is bended When the pickup is installed to only a part of the groove of saddle back page Cutting Template Print gt Page Handling gt Page Scaling O Fit to print margins Reduce to print margins gt O Ey a ae Face Fea O eee 1 Print this file without scaling option 2 Check the size with actual ruler 3 Cut out the dotted line or desire model 4 Adhere to location use double stick tape 5 Cut follow solid line use cutter O 52 5mm gt O iz Preamp Opening Battery Box Opening O 54 0mm gt O
4. ole with template Maskin Cutting Masking 1 Contents Tape g Template Tape Cutting Template 2 Battery Pick Box 3 Pick Up 1 Preamp 4 Clip 5 Screw 2 Tool 2 Drilling hole for pick up 4 Electric Drill 4 Router and Grinder cutting edge 3mm eS SS m oo 2 Drill Bit 5 Round File 2 3mm or 3mm 3 Phillips Screwdriver 6 Masking Tape i i 7 Fix wire with clip 3 Insert EQ and battery box into hole of guitar 4 Fasten screws properly Battery box x Cable 5 Put plugs Battery into jacks Box Solution 1 When there is no sound or sound is stopped Check guitar cable amp or Mixer Check if there is batter or not When it happens noise or distortion please exchange battery Check if the pickup and battery connector is connected correctly or not Check if out put jack is connected correctly 6 Installing the pick up 2 When there is hum noise Check the pickup is connected well or not Check if the connectors are connected to correct position well or not 3 Some causes of the balance problem When the bottom of saddle or the groove of saddle is not flat When saddle is installed to the groove of saddle loosly When the connection is not good between the bottom of saddle and the groove of saddle When Saddle is very short When there is grounds on the groove of saddle When Saddle is declined toward front or back When the top
5. volume Turned fully counter clockwise it is completely OFF Turned fully clockwise it is LOUD 10 Power on off Button The tuner will work with or without a cable plugged into the output jack Battery A 9 volt battery powers the PRENER LC preamp Before connecting the instrument to an amplifier or mixer please check that a fully charged 9 volt battery is connected Tuner Operation Tuner LED Display _ Tuning Guide LED for Sharp tune gt lt Tuning Guide LED for right tune b _ Tuning Guide LED for flat tune NOTE FLAT NOTE IN TUNE AUTO CHROMA rr NOTE SHARP AUTO CHROMA PrE AUTO CHROMA Wi l l l 50 50 50 50 50 Tuner LCD Display Tuner Display The tuner will work with or without a cable plugged into the output jack Pushing the tuner button turns ON the tuner When the tuner is active the output signal is muted No sound will go to the amplifier or mixer when the tuner is active Pushing the tuner button again turns the tuner OFF and the output signal will be active and sound will go to the amplifier If the tuner is ON and the tuner button is not pushed within 2 minutes the tuner will turn OFF automatically and sound returned to the output The tuner Note Readout Display shows the nearest note of one plucked string s sound The Note Read Display read out shows twelve note possibilities in half steps in sharps for example A A B C C D D a
Download Pdf Manuals
Related Search