- Wiedamark
Contents
1. the fiber port the mains supply cable and the 0 10V cable The fiber port should be connected first Connect and secure the fiber optic connector into the aluminium collar and secure using the M5 locking screw Connect the IEC power cord into the Desk Top PSU and plug the mains plug into the electrical supply socket Switch on power the led indicator will illuminate and the illuminator is ready for use In no light is produced consult the TROUBLESHOOTING section Connect the 3 pin XLR sockets on the side panel as detailed below using an approved DMX cable DMX SCREEN SCREEN DMX DMX Plug viewed from rear inside Socket pins NOTE It is recommended that a 1200hm terminating resistor be connected across DMX and DMX on the last illuminator in the DMX universe or cable run 6 Sirius Illuminator Range SETTING THE DMX ADDRESS The DMX address of each illuminator is set manually using the DIP switch accessible on the side panel as shown below DIP DIP Switches Switches Dip Switch Number 1 5 6 8 9 10 Above Example 1 On 6 On 2 Off 7 On 3 Off 8 Off Address 105 4 On 9 Off 5 Off 10 Off DMX OPERATION WHITE LIGHT DIMMING For DMX dimming operation DIP switch 10 must be OFF and the XLR plug s must be plugged into the XLR sockets on the side panel The illuminator can be dimmed on DMX channel 1 as shown in the DMX table overleaf DMX OPERATION DECORATIVE WHEEL CONTROL For2. DMX wheel control DIP switch 10 must be OFF and the XLR plug s must be plugged into the XLR sockets on the side panel The illuminator decorative wheel can be controlled on DMX channel 2 as shown in the DMX table overleaf Universal Fiber Optics o DMX OPERATION LED FAN CONTROL For DMX LED and fan control switch 10 must be OFF and the XLR plug s must be plugged into the XLR sockets on the side panel The illuminator LED and Fan can be controlled on DMX channel 3 as shown in the following DMX table Channel Function Value Description erme foo ite seer coen emea fo ree seer oermea fo orres caora e E emea fo farora N w Sirius Illuminator Range DECORATIVE WHEELS The following decorative wheels are available Color Wheel The standard decorative color wheel has 6 glass segments as follows White Clear Yellow Green Orange Magenta Blue Alternatively a 6 segment or 4 segment vari color wheel can be fitted providing the following color segment options Orange Golden Amber KREBS 018 059 014 Green Jade Turquoise G78 G96 C47 Italian Blue Brilliant Blue Bright Blue Congo C45 B06 B28 B93 Violet Magenta Pink Clear Outputs white V43 M56 M63 light Twinkle Wheel Two variations are available Firstly an un segmented wheel designed to rotate continuously in one direction only Secondly a segmented wheel that with correct DMX controller programming can rotate clock wise and counter clockwise in sequence w
3. Illuminator User Guide NR A Sirius Illuminator Range Models covered by this manual UFOSIRCW UFOSIRCW C UFOSIRCW T UFOSIRSW UFOSIRSW C UFOSIRSW T UFOSIRNW UFOSIRNW C UFOSIRNW T UFOSIRWW UFOSIRWW C UFOSIRWW T UFOSIRGW UFOSIRGW C UFOSIRGW T Please read this manual fully before installing operating or performing Issue 1 Revised 24062014 maintenance on the illuminator unit Universal Fiber Optic Lighting LLC 6119A Clark Center Avenue Sarasota FL34238 Tel 941 343 8115 Fax 941 296 7906 www fiberopticlighting com INTRODUCTION Thank you for purchasing this UFO Illuminator Please read these instructions fully before connecting your unit to the electrical supply and keep them for future reference The UFO Sirius range of illuminators are suitable for use with either glass or PMMA fiber optic harnesses The Sirius is powered by a 100 240 VAC remote desktop power supply unit IMPORTANT THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED Sirius Illuminator Range MODEL TYPES The Sirius LED illuminator incorporates a range of LED arrays focussed through a series of static lenses to provide optimum display and illumination within the following optical range Model Description CRI Color Temperature Lumen Output SIRCW CoolWhite 75 5700K 5700 SIRSW Stud
4. gnal at illuminator due Check input to illuminator using a DMM set to correct to cable or controller fault range amp rectify cable controller fault Responding on RJ45 connector in wrong socket Plug into correct socket wrong channels 4 on illuminator Not responding 5 Manual aimming conio NOL SHES Turn manual dimmer control fully counter clockwise minimum Not responding 6 N ES ei above ciivei Creuli Replace illuminator failure Illuminator dimmed manually or a s Poor light output on by 0 10V or DMX control Check and increase dimmer settings fiber LED driver array failure Replace illuminator 1 white light manual dimming version 2 decorative manual motor version 3 for DMX only 4 decorative or dimming 0 10V control 5 dimming 0 10V control 6 0 10V control Universal Fiber Optics TECHNICAL SPECIFICATIONS Description Details User addressable 0 255 dimming effects wheel control and on off 1 Sirius Illuminator Range NOTES Universal Fiber Optics as UNIVERSAL FIBER OPTICS Universal Fiber Optic Lighting LLC 6119A Clark Center Avenue Sarasota FL34238 Tel 941 343 8115 Fax 941 296 7906 www fiberopticlighting com
5. io White 88 5300K 4650 SIRNW Neutral White 4000K 5300 SIRWW Warm White 3000K 4650 SIRGW Gallery White e 3000K 3450 CONSTRUCTION DETAILS Model Description White light LED with 6 segment decorative colorwheel cool white output manual DMX or UFOSIRCW C 0 10V dimming and wheel control RETE 5 DMX UFOSIRSW C White light LED with 6 segment decorative colorwheel studio white output manual or 0 10V dimming and wheel control UFOSIRNW C White light LED with 6 segment decorative colorwheel neutral white output manual DMX or 0 10V dimming and wheel control White light LED with 6 segment decorative colorwheel warm white output manual DMX or UFOSIRWW C 0 10V dimming and wheel control UFOSIRGW C White light LED with 6 segment decorative colorwheel gallery white output manual DMX or 0 10V dimming and wheel control White light LED with metal decorative twinkle wheel cool white output manual DMX or 0 10V dimming and wheel control White light LED with metal decorative twinkle wheel studio white output manual DMX or UFOSIRSW T 0 10V dimming and wheel control UFOSIRNW T White light LED with metal decorative twinkle wheel neutral white output manual DMX or 0 10V dimming and wheel control UFOSIRWW T White light LED with metal decorative twinkle wheel warm white output manual DMX or 0 10V dimming and wheel control UFOSIRGW T White light LED with metal decorative twinkle wheel gallery white output ma
6. ith an open segment being the full light default position Universal Fiber Optics a MAINTENANCE Please Note that a record of all maintenance MUST be kept in the table below indicating what maintenance was undertaken and when This MUST be dated for warranty purposes Maintenance Undertaken a2 Sirius Illuminator Range TROUBLESHOOTING Problem Possible causes Remedy Mains supply off Check supply and reinstate Unit is dead no light output and Loose mains plug Check plugs PSU power indicator Plug blown fuse UK Check fuse amp replace if necessary Is out PSU failed Replace PSU Unit is dead no Dimming control at minimum Adjust brightness on dimmer control light output but PSU DIP switch no 10 not switched ON Switch DIP switch 10 ON power indicator is lit 1 LED array or drive failure Replace illuminator Motor control at minimum Adjust motor control Decorative wheel is aa DIP switch no 10 not switched ON Switch DIP switch 10 ON not turning 2 Driver circuit or motor failure Replace illuminator DIP switch no 10 is switched ON Switch DIP switch no 10 OFF Sa DMX address not correctly set Set correct DMX address Unit is not responding to DMX No DMX signal from controller Check DMX controller settings control 3 ae j Wiring fault on DMX cables Check cables and repair replace Driver circuit failure Replace illuminator DIP switch no 10 not switched ON Switch DIP switch 10 ON Not responding 4 No 0 10V si
7. nual DMX or 0 10V dimming and wheel control Universal Fiber Optics UFOSIRCW T POWER SUPPLY REQUIREMENTS The LED Illuminator is powered from a multifunction multi voltage desk top Power Supply Unit Remove the 24V Desk Top PSU from its box This PSU is an IEC input device catering for UK European and USA mains supplies using the relevant power cord The SIRIUS LED illuminator must be powered by the supplied 24V 3 75A Desk Top LPS Class 2 power supply GENERAL The SIRIUS is a 90W White Light LED Illuminator with optional decorative wheel capability The SIRIUS LED Illuminator driver PCB has all the control functionality fitted as standard The following control functionality is available see following image 1 Manual dimming 2 Manual Decorative Wheel control various wheel speeds and stop start 3 DMX dimming 4 DMX Decorative Wheel control 5 0 10V Decorative Wheel control channel 1 receiving 6 0 10V dimming channel 2 receiving a Sirius Illuminator Range DIP Switch 10 ON down for DMX ADDRESS AND MANUAL MOTOR manual or 0 10V o DIP Switch MANUAL DIP SWITCH CONTROL 10 OFF up for DMX operation 2 MANUAL DIMMING 24V DC INPUT 0 10V MOTOR 0 10V DMX CONTROL DIMMING CONNECTION MANUAL OPERATION There are 2 connections required the fiber port and the mains supply cable The fiber port should be connected first Connect and secure the fiber optic connector into the green colla
8. r and secure using the M5 locking screw Connect the IEC power cord into the Desk Top PSU and plug the mains plug into the electrical supply socket Switch on power the led Indicator will illuminate and the illuminator is ready for use If no light is produced consult the TROUBLESHOOTING section NOTE THESE ILLUMINATORS ARE NOT MAINS DIMMABLE MANUAL OPERATION WHITE LIGHT DIMMING For normal manual operation DIP switch 10 must be ON During normal manual white light operation the illuminator can be dimmed from 0 to 100 using the Manual Dimming Control on the side panel Universal Fiber Optics MANUAL OPERATION DECORATIVE WHEEL CONTROL For normal manual operation DIP switch 10 must be ON During normal manual decorative operation the illuminator can be dimmed from 0 to 100 using the Manual Dimming Control and the motor can be controlled from stop to 4 speeds slow to fast using the push button Manual Motor Control on the side panel CONNECTION 0 10V OPERATION There are 3 connections required the fiber port the mains supply cable and the 0 10V cable The fiber port should be connected first Connect and secure the fiber optic connector into the aluminium collar and secure using the M5 locking screw Connect the IEC power cord into the Desk Top PSU and plug the mains plug into the electrical supply socket Switch on power the led indicator will illuminate and the illuminator is ready for use In no light is produced con
9. sult the TROUBLESHOOTING section Connect the 0 10V RJ45 as detailed below using CAT5 cable RJ45 CLIP DOWN PINS UP 123 4 5 6 7 8 0 10V RJ45 Connections TOP VIEW OF PLUG VE RJ45 Brown White Pin 7 VE RJ45 Blue White Pin 5 CAT 5 CABLE 1 WHITE ORANGE 2 ORANGE 3 WHITE GREEN 4 BLUE 5 WHITE BLUE 6 GREEN 7 WHITE BROWN 8 BROWN e Sirius Illuminator Range 0 10V OPERATION WHITE LIGHT DIMMING For 0 10v dimming operation DIP switch 10 must be ON the Manual Dimming Control on the side panel must be turned to minimum fully counter clockwise and the RJ45 plug must be plugged into the right hand RJ45 socket on the side panel The illuminator can be dimmed from 0 0 Volts DC to 100 10V DC witha receiving 0 10V signal 0 10V OPERATION DECORATIVE WHEEL CONTROL For 0 10v wheel control DIP switch 10 must be ON and the RJ45 plug must be plugged into the left hand RJ45 socket on the side panel The illuminator decorative wheel can be controlled with a receiving 0 10V signal as detailed in the following 0 10V value table Function WELT Description Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel Color Wheel NOTE For Twinkle wheel control use values marked Universal Fiber Optics ta CONNECTION DMX OPERATION There are 3 connections required
Download Pdf Manuals
Related Search