Quick Start Guide MC
Contents
1. MC II FLOW ANALYZER TOTAL BBLS a 4 RATE BPD r CALIBRATION ENT oec fe oD ee ne WET A cree Ow 49 NuFlo Measurement Systems Enclosure Captive screws Front plate Upper mount z Lower mount S Cord Y connector a Locking screw T Pickup connector Desiccant packet Enclosure Battery Signal cable Plastic retaining strap MC Flaw Analyzer CAUTION The lithium battery that powers the MC II is sealed but a battery leak could expel toxic fumes into the MC II enclosure Before opening the enclosure make sure the enclosure is in a well ventilated area and avoid breathing fumes that could be trapped inside If the battery appears to be damaged adhere to the safety precautions and follow the disposal instructions provided in Appendix C of the user manual eee NuFlo USA Canada International NuFlo Measurement Systems A NuFlo Technologies Company North America 1 800 654 3760 nuflotech nuflotech com Singapore 65 6737 0444 singapore nuflotech com Bognor Regis UK 44 1243 826741 uk nuflotech com Houston TX Corpus Christi TX Longview TX Odessa TX e Duncan OK Shreveport LA Houma LA Lafayette LA Laurel MS Bakersfield CA Saginaw MI e Casper WY Broomfield CO Dallas TX Tulsa OK Calgary AB e Edmonton AB Jakarta Indonesia Aberdeen Scotland Bognor Regis UK Dubai UAE Hassi M2. in pulses per gallon The cubic meters Ano MC II will automatically T calculate the divisor bot barrels RATE gallons GA RATE liters ie 1c Er RATE If you select uSEr Ent diV will appear in the top display Enter a calculated divisor in terms of specified unit from right to left Press INCREMENT to select each digit press ENTER STEP to advance to the next digit Proceed to Step 4 user defined uSEr RATE EE E OE E UUS E UE TOTAL Walala ETE Od O AA I I I RATE Locate the flowmeter calibration factor pulses per gallon on a plastic tag attached to the meter Enter the number as follows a Press DEC POINT repeatedly to position your decimal point for the calibration factor b Enter the digits from right to left beginning with the flashing digit to the far right Press INCREMENT to select digits between 0 and 9 or press and hold INCREMENT to scroll the digits Press ENTER STEP to save the selection Repeat this step to enter all six digits If your calibration factor is less than six digits in length enter O for remaining digits When the last sixth digit is saved the calibration factor will be saved in the MC II s memory and rAt Eng will appear in the top display At the rAt Eng prompt select a unit of measure for rate ba
3. on the bolt that holds the MC II readout on the upper mount tilt the unit to the desired angle and retighten the nut Step 2 Install Field Wiring Connect the battery and flowmeter signal cable as shown NuFlo I S Battery P N 100005111 CLASS I GROUPS A B C D DIVISION 1 HAZARDOUS AREA 100005109 991 43179 REV O TOTALIZER BOARD DOTTED LINES INDICATE OPTIONAL SHIELDING CONNECTIONS TURBINE MAGNETIC PICKUP TURBINE MAGNETIC PICKUP MAY BE 991 OR 458 SERIES NUFLO FLOWMETER OR ANY APPROVED DEVICE WITH THE FOLLOWING MAXIMUM ENTITY PARAMATERS Vmax 6 0 VDC or peak Voc 5 88 VDC ISC 2 94 mA Ca 15 uF max La 2 H max Step 3 Calibrate the MC II The following information is needed to calibrate the MC II 3 unit of measure for volume flowmeter calibration factor in pulses per gallon unit of measure for flow rate Press ACCESS to enter Calibrate mode Prog no will appear in the top display and the version number of the firmware will appear in the bottom display The tot Eng menu will then appear in the top display and the default volume unit bbL will appear in the bottom display Press INCREMENT until the desired unit of measure appears in the bottom display Press ENTER STEP LECO COE ENJ TOTAL If you select a preprogrammed unit bbl gal m liter Pu P gAL will appear in the top display Go to Step 3 for instruction on entering your flowmeter s calibration factor
4. essaoud Algeria Singapore www nuflotech com HOUSTON HEAD OFFICE 281 582 9500 Quick Start Guide MIC II Flow Analyzer MC II FLOW ANALYZER TOTAL BBLS RATE BPD r CALIBRATION ENTER DEC INCRE VIEW ACCESS POINT MENT a RESET 49 NuFlo Measurement Systems A Quick Reference on Mounting Wiring and Calibrating the MC II Flow Analyzer For complete instructions see the MC II Flow Analyzer User Manual Part No 100079666 Part No 50165001 Rev A Step 1 Mount the MC II Direct Mount For remote mount instructions see the User Manual 1 Plug the MC II cable connector into the magnetic pickup and turn the swivel nut clockwise until the connector is fully inserted into the pickup and the swivel nut is hand tight Loosen the locking screws that secure the base MC II mount Position the MC II on the flowmeter carefully pulling excess signal cable through the strain relief cord connec tor on the side of the upper mount Thread the base of the mount onto the conduit adapter of the turbine meter and tighten two extra rounds after it is hand tight DO NOT allow the upper mount and MC II readout to turn while tightening the base to avoid damag ing the signal cable Tighten the outside nut of the strain relief cord connector on the upper mount with a 15 mm open end wrench to prevent cord slippage If necessary adjust the MC II readout for best viewing Loosen the nut
5. its Remember your password You will be asked for it each time you press ACCESS to enter the Calibration mode or RESET to reset the total
6. rrels 5 D per day RATE gallons aya PE leu lt unit gt per minute _ i ae per day cubic meters nn fae o gt per day _ aa per hour liters 6 __ p _ _ lt unit gt per minute SW 11 W per minute lt unit gt CI JCL per second To select a unit of measure for rate press INCREMENT until the desired unit of measure appears in the bottom display If you selected a user defined unit of measure for volume in Step 2 your rate unit options will be per day per hour per minute or per second Press ENTER STEP PULSE will appear in the top display Select or deselect the Pulse Output option using INCREMENT to scroll through the available settings If your MC II is not configured with the pulse output option press ENTER STEP to accept the default setting OFF and proceed to Step 6 If your MC II is configured with the pulse output option set the scale factor in the user interface and set jumper W1 on the pulse output board to 1 Press INCREMENT repeatedly to select the volume increment that will cause a pulse output to occur Press ENTER STEP CodE will appear in the top display Enable or disable the password protected security feature Press ENTER STEP to retain the default no setting or press INCREMENT to toggle the setting to YES password protection enabled Press ENTER STEP A data entry field will appear in the bottom screen Enter a numeric password containing up to six dig
Download Pdf Manuals
Related Search