Home

NP600/NP500/NP400/ NP300/NP500W NP600S

1. An image can be distorted during the adjustment of CLOCK and PHASE This is not malfunction The adjustments for CLOCK PHASE HORIZONTAL and VERTICAL will be stored in memory for the current signal The next time you project the signal with the same resolution horizontal and vertical frequency its adjustments will be called up and applied To delete adjustments stored in memory from the menu you select RESET CURRENT SIGNAL or ALL DATA and reset the adjustments Selecting Overscan Percentage OVERSCAN Select overscan percentage 0 5 and 10 for signal Projected image Overscaned by 1096 NOTE e The 0 cannot be selected when VIDEO and S VIDEO signals are used OVERSCAN is not available when NATIVE is selected for ASPECT RATIO 59 5 Using On Screen Menu Selecting Aspect Ratio ASPECT RATIO The term aspect ratio refers to the ratio of width to height of a projected image The projector automatically determines the incoming signal and displays it in its appropriate aspect ratio This table shows typical resolutions and aspect ratios that most computers support
2. 00000000000000000000000000000000000 f Lens center 308 12 1 78 3 1 76 3 0 E Lens center 55 3 2 2 oo Or 89 7 Appendix Unit mm inch 7 Appendix NP600S NP500WS 00000000000000000000000000000000000 301 5 11 9 Lens center 143 2 5 6 Unit mm inch 90 7 Appendix Pin Assignments of D Sub COMPUTER Input Connector Mini D Sub 15 Pin Connector Signal Level Video signal 0 7Vp p Analog Sync signal TTL level RGB Signal Analog YCbCr Signal Red Cr Green or Sync on Green Y Blue Cb Ground Ground Red Ground Cr Ground Green Ground Y Ground Blue Ground Cb Ground Pin No 1 2 3 4 5 6 7 8 9 No Connection Sync Signal Ground No Connection Bi directional DATA SDA Horizontal Sync or Composite Sync Vertical Sync Data Clock 91 7 Appendix Q Compatible Input Signal List Horizontal 15KHz to 100KHz RGB 24KHz or over Vertical 50Hz to 120Hz Signal Resolution Frequency H Refresh Rate Dots kHz Hz VIDEO
3. DESKTOP FRONT CEILING REAR DESKTOP REAR CEILING FRONT 66 5 Using On Screen Menu Disabling the Cabinet Buttons CONTROL PANEL LOCK This option turns on or off the CONTROL PANEL LOCK function NOTE This CONTROL PANEL LOCK does not affect the remote control functions When the control panel is locked pressing and holding the EXIT button on the projector cabinet for about 10 seconds will change the setting to OFF TIP When the CONTROL PANEL LOCK is turned on a key lock icon will be displayed at the bottom right of the menu Enabling Security SECURITY This feature turns on or off the SECURITY function Unless the correct keyword is entered the projector cannot project an image page 42 NOTE Your setting will not be affected even when RESET is done from the menu Selecting Communication Speed COMMUNICATION SPEED This feature sets the baud rate of the PC Control port D Sub 9P It supports data rates from 4800 to 19200 bps The default is 19200 bps Select the appropriate baud rate for your equipment to be connected depending on the equip ment a lower baud rate may be recommended for long cable runs NOTE Your selected communication speed will not be affected even when RESET is done from the menu 67 5 Using On Screen Menu Se
4. Resolution Aspect Ratio VGA 640 x 480 43 SVGA 800 x 600 43 XGA 1024 x 768 43 WXGA 1280 x 768 15 9 WXGA 1280 x 800 16 10 WXGA 1440 x 900 16 10 SXGA 1280 x 1024 5 4 SXGA 1400 x 1050 43 UXGA 1600 x 1200 43 Options Function AUTO The projector will automatically determine the incoming signal and display it in its aspect ratio next page The projector may erroneously determine the aspect ratio depending on its signal If this occurs select the appropriate aspect ratio from the following 4 3 The image is displayed in 4 3 aspect ratio 16 9 The image is displayed in 16 9 aspect ratio 15 9 The image is displayed in 15 9 aspect ratio 16 10 The image is displayed in 16 10 aspect ratio WIDE ZOOM The image is stretched left and right NP600 NP500 NP400 Parts of the displayed image are cropped at the left and right edges and therefore not NP300 NP600S visible LETTERBOX The image of a letterbox signal is stretched equally in the horizontal and vertical direc NP500W NP500WS tions to fit the screen Parts of the displayed image are cropped at the top and bottom edges and therefore not visible NATIVE The projector displays the current image in its true resolution when the incoming computer signal has a lower resolution than the projector s native resolution Example 1 When the incoming sig nal with the resolution of 800 x 600 is displayed on the NP600 NP500 NP400 NP300 NP600S Example 2
5. Lamp Mode Normal Eco Information on input signal Horizontal synch frequency kHz Vertical synch frequency Hz Synch polarity HD O VO LJ C Synch type Separate Composite Sync on Green STATUS Indicator Steady light Flashing light Remote control model number Orange Green cycles Projector oo DVD player Installation environment Screen size inch Screen type White matte Beads Polarization Wide angle High contrast Throw distance feet inch m Orientation Ceiling mount Desktop Power outlet connection Connected directly to wall outlet Connected to power cord extender or other the number of connected equipment Connected to a power cord reel or other the number ofconnectedequipnent Computer Manufacturer Model number Notebook PC Desktop Native resolution Refresh rate Video adapter Other Signal cable NEC standard or other manufacturer s cable Model number Length Distribution amplifier Model number Switcher Model number Adapter Model number inch m 95 Video equipment VCR DVD player Video camera Video game or other Manufacturer Model number Q TravelCare Guide TravelC
6. INPUT Model COMPUTER 1 IN COMPUTER 2 IN analog analog digital NP600 NP500 NP400 NP300 NP600S Yes No Yes NP500W NP500WS Yes Yes Yes COMPUTER 1 IN d j VGA signal cable supplied To mini D Sub 15 pin connector on the projector It is Audio cable recommended that you use a commercially available dis not supplied tribution amplifier if connecting a signal cable longer than the cable supplied 4 NOTE For older Macintosh use a commercially available EB pin adapter not supplied to connect to your Mac s video 10 PHONE port Lg 89 IBM VGA or Compatibles Notebook type or Macintosh Notebook type 17 2 Installation and Connections Select the source name for its appropriate input connector after turning on the projector Input connector SOURCE EURE en ne ete eae Button on the remote control cabinet COMPUTER 1 IN COMPUTER1 COMPUTER 1 COMPUTER 2 DIGITAL COMPUTER 2 COMPUTER 2 DVI I IN or Toggle COMPUTER 2 ANALOG COMPUTER 2 NOTE The projector is not compatible with video decoded outputs of the N
7. Using the DIGITAL ZOOM function from ing the manual zoom lever Using the u eve the menu Using the manual focus ring Using the manual focus lever For further details on the specifications see page 85 1 Effective pixels are more than 99 99 2 This is the light output value lumens when the PRESET mode is set to HIGH BRIGHT If any other mode is selected as the PRESET mode the light output value may drop slightly 3 Compliance with ISO21118 2005 TIP The model name is located on the cabinet Model name 1 Introduction Q Part Names of the Projector Front Top NP600 NP500 NP400 NP300 NP500W Controls gt page 7 Security chain opening Attach an anti theft device Focus Ring The security chain opening accepts se page 33 curity wires or chains up to 0 18 inch 4 6 mm in diameter Remote sensor gt page 10 Leng Built in Security Slot 1 Ventilation inlet Filter Cover page 76 Lens Ca Adjustable Tilt Foot Lever page 31 Adjustable Tilt Foot page 31 This security slot supports the MicroSaver amp Security System NP600S NP500WS Controls gt page 7 Security chain opening Attach an anti theft device The security chain opening accepts se curity wires or chains up to 0 18 inch 4 6 mm in diameter Focus Lever page
8. SOURCE ADJUST MENU INSTALLATION SOURCE ADJUST RESET LATION OPTIO AUTO KEYSTONE OFF DIGITAL ZOOM gt 100 KEYSTONE 4e UM AUTO KEYSTONE OFF KEYSTONE SAVE OFF KEYSTONE EM WALL COLOR OFF KEYSTONE SAVE OFF LAMP MODE NORMAL WALL COLOR OFF CLOSED CAPTION OFF LAMP MODE NORMAL LANGUAGE 9 ENGLISH CLOSED CAPTION OFF LANGUAGE gs ENGLISH CT DENT CJ COMPUTER1 CJ COMPUTER Using Digital Zoom DIGITAL ZOOM NP600S NP500WS This feature allows you to electronically fine adjust the image size on the screen Use 4 or button to large or reduce the projected image TIP To adjust the projected image size roughly move the projector away or closer to the screen page 30 To fine adjust the zoom use the DIGITAL ZOOM function Enabling Auto Keystone AUTO KEYSTONE This feature allows the projector to detect its tilt and correct vertical distortion automatically To turn on the AUTO KEYSTONE feature select ON To adjust the KEYSTONE feature manually select OFF Correcting Vertical Keystone Distortion Manually KEYSTONE You can correct vertical distortion manually page 34 TIP When this option is highlighted pressing the ENTER button will display its slide bar for adjustment Saving Vertical Keystone Correction KEYSTONE SAVE This option enables you to save your current keystone settings OFF em Does not save current keystone correction settings It w
9. 2 Push and hold the Adjustable Tilt Foot Lever on the front of S rs Tilt Adjustable Tilt Foot the projector to extend the adjustable tilt foot 3 Lower the front of the projector to the desired height 4 Release the Adjustable Tilt Foot Lever to lock the Adjustable tilt foot The tilt foot can be extended up to 1 8 inch 45 mm There is approximately 10 degrees up of adjustment for the front of the projector Rotate the rear foot to the desired height in order to square the image on the projection surface Adjustable Tilt A CAUTION Foot Lever Do not use the tilt foot for purposes other than originally intended Misuses such as using the tilt foot to carry or hang from the wall or ceiling the projector can cause damage to the projector Adjusting the left and right tilt of an image Rear foot 1 Remove the spacer black rubber from the rear foot Keep the spacer for future use 2 Rotate the rear foot The rear foot can be extended up to 0 4 inch 10 mm Rotating the rear foot allows the projector to be placed horizontally NOTE Do not extend the rear foot beyond its height limit 0 4 inch 10 mm Doing so may cause the rear foot to come out of the projector After using the projector attach the spacer to the rear foot Rear foot Spacer black rubber 31 3 Projecting an Image Basic Operation NP600 NP500 NP400 NP300 NP500W Use the ZOO
10. 54 5 Using On Screen Menu Menu Descriptions amp Functions SOURCE ADJUST SETUP INFO RESET COMPUTER COMPUTER2 DIGITAL gt COMPUTER2 ANALOG D VIDEO 2 S VIDEO COMPUTER1 Selects the computer connected to your COMPUTER 1 IN input connector NOTE e When the component input signal is connected to the COMPUTER 1 IN connector select COMPUTER1 The projector will determine if the input signal is RGB or component signal COMPUTER2 DIGITAL amp ANALOG Selects the computer connected to your COMPUTER 2 IN DVI I connector VIDEO Selects what is connected to your VIDEO input VCR DVD player or document camera S VIDEO Selects what is connected to your S VIDEO input VCR or DVD player NOTE A frame may freeze for a brief period of time when a video is played back in fast forward or fast rewind with a Video or S Video source 55 5 Using On Screen Menu Q Menu Descriptions amp Functions ADJUST PICTURE SOURCE SETUP INFO RESET PRESET 2 PRESENTATION GL DETAIL SETTINGS CONTRAST e ep BRIGHTNESS Ax SHARPNESS 4 cmm RESET Cie SE EXIT H CJ COMPUTER PRESET This function allows you to select optimized settings for your projected image You can adjust neutral tint for yellow cyan or magenta There are six factory presets optimized for various types of images You can also use DETAIL SETTINGS to set u
11. icr Enabling this option automatically assigns an IP address to the projector from your DHCP server Disabling this option allows you to register the IP address or subnet mask number obtained from your network administrator NOTE The IP address of the projector is required to change the network setting The IP address will not be displayed on the projector s menu Consult your network administrator for the IP address when ENABLE is selected for DHCP IP ABDRESS es Set your IP address of the network connected to the projector when DISABLE is selected for DHCP SUBNET MASK Set your subnet mask number of the network connected to the projector when DISABLE is selected for DHCP DEFAULT GATEWAY Set your default gateway of the network connected to the projector when DISABLE is selected for DHCP DNS PRIMARY Set your primary DNS settings of the network connected to the projector DNS SECONDARY Set your secondary DNS settings of the network connected to the projector UPDATE tiene Reflect your settings NOTE Close the browser after clicking UPDATE The projector will automatically update your settings TIP Selecting NETWORK SETTINGS for RESET from the projector s menu allows you to return the following items to the factory default DHCP DISABLE IP ADDRESS 192 168 0 10 SUBNET MASK 255 255 255 0 DEFAULT GATEWAY
12. The term letterbox refers to a more landscape oriented image when compared to a 4 3 image which is the standard aspect ratio for a vide source The letterbox signal has aspect ratios with the vista size 1 85 1 or cinema scope size 2 35 1 for movie film The term squeeze refers to the compressed image of which aspect ratio is converted from 16 9 to 4 3 61 5 Using On Screen Menu Adjusting the Vertical Position of Image POSITION not available on NP500W NP500WS only when 16 9 15 9 or 16 10 is selected for ASPECT RATIO When 16 9 15 9 or 16 10 is selected in ASPECT RATIO the image is displayed with black borders on the top and bottom You can adjust the vertical position from the top to the bottom of the black area ais C er O Selecting Video Filter Level VIDEO FILTER not available for Digital RGB Video and S Video Select one of the three levels for reducing video noise OFF LESS or MORE OFF sis The low pass filter is turned off LESS cette The low pass filter is applied partially MORE s The low pass filter is applied fully NOTE e Selecting OFF will give best image quality by way of higher bandwidth Selecting LESS will soften the image and selecting MORE will soften the image more 62 5 Using On Screen Menu Q Menu Descriptions amp Functions SETUP GENERAL NP600 NP500 NP400 NP300 NP500W NP600S NP500WS
13. page 45 46 7 MENU Button page 51 8 SELECT AV lt gt Button page 51 9 ENTER Button page 51 10 EXIT Button page 51 11 MOUSE L CLICK Button page 45 46 12 MOUSE R CLICK Button page 45 46 13 VIDEO Button page 29 14 S VIDEO Button page 29 15 COMPUTER 1 2 Button page 29 16 AUTO ADJ Button page 37 17 VOLUME Button page 37 18 LAMP MODE Button page 41 19 ASPECT Button page 60 20 PICTURE Button page 56 57 21 HELP Button page 73 22 FREEZE Button page 40 The PAGE UP DOWN MOUSE L CLICK and MOUSE R CLICK buttons work only when the optional remote mouse receiver is connected with your computer Battery Installation 1 Press firmly and slide the 2 Install new batteries AAA En battery cover off sure that you have the batteries polarity aligned correctly Remote Control Precautions Handle the remote control carefully fthe remote control gets wet wipe it dry immediately Avoid excessive heat and humidity Do not heat take apart or throw batteries into fire 1 Introduction 3 Slip the cover back over the bat teries until it snaps into place Do not mix different types of batteries or new and old batteries f you will not be using the remote control for a long time remove the batteries Ensure that you have the batteries polarity aligned correctly
14. 7 Appendix Model Number NP600S NP500WS Optical NP600S NP500WS LCD Panel 0 63 inch LCD with Micro Lens Array 0 59 inch LCD with Micro Lens Array Aspect Ratio 4 3 Aspect Ratio 16 10 Resolution 1024 x 768 pixels 1280 x 800 pixels Lens Fixed zoom and manual focus Digital Zoom Ratio 1 2 F2 3 f 9 7 mm Lamp 230W AC 170W in ECO Mode Light Output 2600 lumens approx 70 in ECO Mode 2100 lumens approx 70 in ECO Mode Contrast Ratio s full white full black 600 1 Image Size Diagonal 60 110 1 52 m 2 79 57 104 1 45 m 2 64 m Projection Distance 35 66 0 9 m 1 7 m 36 66 0 9 m 1 7 m Projection Angle 29 1 29 4 1 Effective pixels are more than 99 99 2 This is the light output value lumens when the PRESET mode is set to HIGH BRIGHT If any other mode is selected as the PRESET mode the light output value may drop slightly 8 Compliance with ISO21 118 2005 Electrical Inputs 1 RGB Component D Sub 15 P 1 RGB Digital Analog DVI I 29 P HDCP supported 1 S Video DIN 4 P 1 Video RCA 1 L R RCA Audio 2 Stereo Mini Audio Outputs 1 RGB D Sub 15P 1 Stereo Mini Audio PC Control 1 PC Control Port D Sub 9P Wired LAN Port RJ 45 External Control RS232 IR Wired LAN Color Reproduction 16 7 million colors simultaneously Full color Compatible Signals Analog VGA SVGA XGA W
15. Do not use new and old batteries together or use different types of batteries together Dispose of used batteries according to your local regulations Operating Range for Wireless Remote Control 7m 22feet Remote control 7m 22feet The infrared signal operates by line of sight up to a distance of about 22 feet 7 m and within a 60 degree angle of the remote sensor on the projector cabinet The projector will not respond if there are objects between the remote control and the sensor or if strong light falls on the sensor Weak batteries will also prevent the remote control from properly operating the projector 10 2 Installation and Connections This section describes how to set up your projector and how to connect video and audio sources Your projector is simple to set up and use But before you get started you must first 1 2 7 ZA Set up a screen and the projector Connect your computer or video equip ment to the projector page 17 19 20 21 22 23 24 Connect the supplied power cable page 25 g2 NOTE Ensure that the power cable and any other cables are disconnected before moving the projec tor When moving the projector or when it is not in use cover the lens with the lens cap To the wall outlet Q Setting Up the Screen and the Projector Selecting a Location NOTE Throw dis
16. 192 168 01 DNS PRIMARY and DNS SECONDARY will remain unchanged 48 4 Convenient Features Alert Mail Setting http the projector s IP address lanconfig html PROJECTOR NETWORK SETTINGS ITEM VALUE DOMAIN HOST NAME DOMAIN NAME B PEERS oO ALERT MAIL OENABLE DISABLE SENDER S ADDRESS SMTP SERVER NAME RECIPIENT S ADDRESS 1 RECIPIENT S ADDRESS 2 RECIPIENT S ADDRESS 3 em TEST MAIL STATUS Copyright C NEC Display Solutions Ltd 2008 All rights reserved This option notifies your computer of an error message via e mail when using wired LAN An error message notification will be sent when the projector lamp has reached the end of its usable life or an error occurs in the projector HOST NAME Type in the hostname of the network connected to the projector Up to 60 alphanumeric char acters can be used If the host name is unknown type in a string of characters representing the projector Example Projector 1 DOMAIN NAME Type in the domain name of the network connected to the projector Up to 60 alphanumeric characters can be used If the domain name is unknown type in the right side of in the sender s address Example nec com ALERT MAIL Checking ENABLE will turn on the Alert Mail feature Checking DISABLE will turn off the Alert Mail feature
17. NEC Portable Projector NP600 NP500 NP400 NP300 NP500W NP600S NP500WS User s Manual RSS NEC AAA NL NE NY SSS TS AAAS WAN SX The projector s model name indicated on the projector s label is NP600 NP500 NP400 NP300 NP500W NP600S NP500WS NP600G NP500G NP400G NP300G NP500WG NP600SG and NP500WSG respectively All the models are referred to as NP600 NP500 NP400 NP300 NP500W NP6008S and NP500WS throughout the user s manual except some of the specification pages 2nd edition February 2009 BM is a trademark or registered trademark of International Business Machines Corporation Macintosh Mac OS X and PowerBook are trademarks of Apple Inc registered in the U S and other countries Microsoft Windows Windows Vista Internet Explorer and PowerPoint are either a registered trademark or trademark of Microsoft Corporation in the United States and or other countries MicroSaver is a registered trademark of Kensington Computer Products Group a division of ACCO Brands Other product and company names mentioned in this user s manual may be the trademarks or registered trademarks of their respective holders NOTES 1 The contents of this user s manual may not be reprinted in part or whole without permission 2 The contents of this user s manual are subject to change without notice 3 Great care has been taken in the preparation of this user
18. Q Turning off the Image and Sound Press the PIC MUTE button to turn off the image and sound for a short period of time Press again to restore the image and sound NOTE Even though the image is turned off the menu still remains on the screen e Sound from the AUDIO OUT jack Stereo mini can be turned off Freezing a Picture Press the FREEZE button to freeze a picture Press again to resume motion NOTE The image is frozen but the original video is still playing back Enlarging a Picture You can enlarge the picture up to four times NOTE The maximum magnification may be less than four times depending on the signal To do so 1 Press the MAGNIFY button to magnify the picture To move the magnified image use the SELECT A W 4 or button 40 4 Convenient Features 2 Press the SELECT AY lt gt button The area of the magnified image will be moved 3 Press the MAGNIFY button Each time the MAGNIFY button is pressed the image is reduced NOTE The image will be enlarged or reduced at the center of the screen Displaying the menu will cancel the current magnification Q Changing Lamp Mode This feature enables you to select two brightness modes of the lamp Normal and Eco modes The lamp life can be extended by using the Eco mode Lamp Mode Description Status of LAMP indicator NORMAL
19. BACKGROUND Use this feature to display a blue black screen or logo when no signal is available The default background is BLUE NOTE Your setting will not be affected even when RESET is done from the menu 65 5 Using On Screen Menu Selecting Interval Time for Filter Message FILTER MESSAGE This option allows you to select the time preference between displaying the message for cleaning the filters Clean the filter when you get the message PLEASE CLEAN FILTER page 76 Five options are available OFF 100 H 200 H 500 H 1000 H The default setting is 500 H NOTE Your setting will not be affected even when RESET is done from the menu Turning ON OFF Control ID ID DISPLAY Available only when the optional remote control NPO2RC is used ID DISPLAY This option turns on or off the ID number which is displayed when the ID SET button on the remote control is pressed INSTALLATION SOURCE ADJUST GENERAL MENU OPTIONS 1 1 2 ORIENTATION DESKTOP FRONT CONTROL PANEL LOCK OFF SECURITY OFF COMMUNICATION SPEED 19200bps CONTROL ID EXEX SELECT GUu EXIT e MOVE e MOVE IY Selecting Projector Orientation ORIENTATION This reorients your image for your type of projection The options are desktop front projection ceiling rear projection desktop rear projection and ceiling front projection
20. NTSC PAL PAL60 SECAM IBM Apple Macintosh HDTV 1080i 60 1080i 50 SDTV 480p DVD YCbCr Progressive X X x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x NOTE Images above flagged wit are not supported by digital signal e An image with higher or lower resolution than the projector s native resolution NP600 NP500 NP400 NP300 NP600S 1024 x 768 NP500W NP500WS 1280 x 800 will be displayed with Advanced AccuBlend Some composite sync signals may not be displayed correctly Signals other than those specified in the table above may not be displayed correctly If this should happen change the refresh rate or resolution on your PC Refer to Display Properties help section of your PC for procedures a 92 Q PC Control Codes and Cable Connection PC Control Codes Function Code Data POWER ON 02H OOH OOH OOH OOH 02H POWER OFF 02H 01H OOH OOH 00H INPUT SELECT COMPUTER 1 02H 03H OOH OOH 02H 01H 01H OSH INPUT SELECT COMPUTER 2 Digital 02H 03H OOH OOH 02H 01H 1AH 22H INPUT SELECT COMPUTER 2 Analog 02H O3H OOH OOH 02H 01H 02H OAH INPUT SELECT VIDEO 02H 03H OOH OOH 02H 01H 06H OEH INPUT SELECT S VIDEO 02H 03H
21. The projector will turn off and go into standby mode when you continue to use the projector for another 100 hours after the lamp has reached the end of its life If this happens be sure to replace the lamp If you continue to use the lamp after the lamp reaches the end of its life the lamp bulb may shatter and pieces of glass may be scattered in the lamp case Do not touch them as the pieces of glass may cause injury If this happens contact your NEC dealer for lamp replacement NOTE This message will be displayed under the following conditions for one minute after the projector has been powered on e when the POWER button on the projector cabinet or the POWER OFF button on the remote control is pressed To turn off the message press any button on the projector cabinet or the remote control To replace the lamp Optional lamp and tools needed for replacement e Replacement lamp NPO7LP 79 6 Maintenance 1 Remove the lamp cover 1 Loosen the lamp cover screw The lamp cover screw is not removable 2 Push and slide the lamp cover off 2 Remove the lamp housing 1 Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling condi tion The two screws are not removable There is an interlock on this case to prevent the risk of electrical shock Do not attempt to circumvent this interlock 2 Remove the lamp housing by holding it A caution Make
22. There are 3 types of Service available Enduser has to understand following condition and is required to fill in the Application Sheet 1 Repair and Return The Faulty unit is sent or collected from the customer It is repaired and returned within 10 days to the customer excluding transport time There may have a case repair and return can t be done by NEC Authorized Service Station because of shortage of spare parts due to same model is not sold in the territory 2 Repair and Return with Loan This service is limited to some Service Stations This service is offered to the Enduser who cannot wait until their unit is repaired The customer can borrow a unit for US 200 up to 12 days Customer then sends in inoperable unit to nearest NEC Authorized Service Station for service In order to prevent collection problem Enduser is required to fill in Application Sheet Enduser needs to confirm the availability of the Service to NEC Authorized Service Stations 3 Loan Only For this service NEC Authorized Service Station supplies the cus tomer with a loan unit for US 200 up to 12 days Customer keeps the inoperable unit and when customer returns home customer arranges to have the projector serviced in the home country 2 Warranty Exclusions This program does not apply if the Projector s serial number has been defaced modified or removed If in the judgement of NEC Authorized Service Station or its agent the defec
23. KEYSTONE screen 5 Press the SELECT A or button to select ON and press the ENTER button 6 Press the MENU button The menu will be closed NOTE e The maximum range of vertical keystone correction is 30 degrees on the NP600 NP500 NP400 NP300 NP500W 20 degrees on the NP600S NP500WS The maximum range of keystone correction may be lower depending on the signal or aspect ratio selection The range of keystone correction is not the maximum tilt angle of projector The Auto Keystone correction will take effect in 2 seconds after changing the projection angle during projection The left and right horizontal keystone correction is not available Place the projector so that the lens surface is parallel to the screen The rear feet of the projector can be adjusted to level the projector Using keystone correction can cause the image to be slightly blurred because the correction is made electronically TIP If you have one of the following conditions the projector s Auto Keystone may not be performed correctly The screen is tilted The room temperature is too high or too low The optical zoom is maximized or minimized 36 3 Projecting an Image Basic Operation Q Optimizing Computer Signal Automatically Adjusting the Image Using Auto Adjust Optimizing a computer image automatically Press the AUTO ADJ button to optimize a computer image automatically This adjustment may be necessary when y
24. ON an XGA 1024 x 768 signal may not be recognized on NP600 NP500 NP400 NP300 or NP600S In this case select OFF Enabling the deinterlace DEINTERLACE Turns on or off the deinterlace function for a telecine signal ORE ims Select this option if there is any jitter or artifacts in video ON Default standard setting NOTE This feature is not available for RGB 480p 576p and HDTV signals Enabling Key Sound and Error Sound BEEP This feature turns on or off the button sound or alarm when the following operations are performed Displaying the main menu Switching sources Resetting data by using RESET Pressing POWER ON or POWER OFF button 70 5 Using On Screen Menu OPTIONS 2 SOURCE ADJUST INFO RESET OFF TIMER OFF STANDBY MODE NORMAL AUTO POWER ON AC OFF AUTO POWER ON COMP1 OFF AUTO POWER OFF OFF DEFAULT SOURCE SELECT LAST CD SELECT CU EXT MOVE MOVE CO COMPUTERI Using Off Timer OFF TIMER 1 Select your desired time between 30 minutes and 16 hours OFF 0 30 1 00 2 00 4 00 8 00 12 00 16 00 2 Press the ENTER button on the remote control 3 The remaining time starts counting down 4 The projector will turn off after the countdown is complete NOTE To cancel the preset time set OFF for the preset time or turn off the power e When the remaining time reaches 3 minutes before the projector is turned off the THE PROJECTOR WILL TURN OFF WITHIN
25. OOH OOH 02H 01H OBH 13H PICTURE MUTE ON 02H 10H OOH OOH 00H 12H PICTURE MUTE OFF 02H 11H OOH OOH 00H 13H SOUND MUTE ON 02H 12H OOH OOH 00H 14H SOUND MUTE OFF 02H 13H OOH OOH 00H 15H 7 Appendix NOTE Contact your local dealer for a full list of the PC Control Codes if needed Cable Connection Communication Protocol Baud um P rity iuis Stop bit eene X on off sss Communications procedure No parity One bit NOTE Depending on the equipment a lower baud rate may be recommended for long cable runs PC Control Connector D SUB 9P To TxD of PC To RxD of PC To GND of PC o 99999 To RTS of PC To CTS of PC NOTE 1 Pins 1 4 6 and 9 are no used NOTE 2 Jumper Request to Send and Clear to Send together on both ends of the cable to simplify cable connection NOTE 3 For long cable runs it is recommended to set communication speed within projector menus to 9600 bps 93 Q Troubleshooting Check List Before contacting your dealer or service personnel check the following list to be sure repairs are needed also by referring to the Troubleshooting section in your user s manual This checklist below will help us solve your problem more efficiently Print this page and the next page for your check Frequency of occurrence
26. Power always L No power POWER indicator does not light green See also Status Indicator STATUS Power cable s plug is fully inserted into the wall outlet Main power switch is pressed to the ON position Lamp cover is installed correctly Lamp Hours Used lamp operation hours was cleared after lamp replacement No power even though you press and hold the POWER button for 1 second Video and Audio Other d dd CT No image is displayed from your PC or video equipment to the projector Still no image even though you connect the projector to the PC first then start the PC Enabling your notebook PC s signal output to the projector Acombination of function keys will enable disable the exter nal display Usually the combination of the Fn key along with one of the 12 function keys turns the external display on or off No image blue or black background no display Still no image even though you press the AUTO ADJUST button Still no image even though you carry out RESET in the projectors menu Signal cable s plug is fully inserted into the input connector A message appears on the screen The source connected to the projector is active and available Still no image even though you adjust the brightness and or the contrast Input s
27. Telephone 81 465 85 2369 Fax Line 81 465 85 2393 Email Address support pjweb gw necds nec co jp WEB Address http www nec pj com Regions Covered Japan NEC Solutions China Co Ltd Address Rm 1903 Shining Building 35 Xueyuan Rd Haidian District Beijing 100083 P R C Telephone 8610 82317788 Fax Line 8610 82331722 Email Address Lily necsl com cn Johnson liu 9 necsl com cn WEB Address http www necsl com cn Regions Covered China NEC Hong Kong Ltd Address 25 F The Metropolis Tower 10 Metropolis Drive Hunghom Kowloon Hong Kong Telephone 852 2369 0335 Fax Line 852 2795 6618 Email Address nechksc Q nechk nec com hk esmond_au nechk nec com hk WEB Address http www nec com hk Regions Covered Hong Kong NEC Taiwan Ltd Address 7F No 167 SEC 2 Nan King East Road Taipei Taiwan R O C Telephone 886 2 8500 1700 Fax Line 886 2 8500 1420 Email Address eric nec com tw WEB Address http www nec com tw Regions Covered Taiwan NEC Asia Pte Ltd Address 401 Commonwealth Drive 07 02 Haw Par Technocentre Singapore 149598 Telephone 65 6 273 8333 Fax Line 65 6 274 2226 Email Address ncare Gnec com sg WEB Address http www nec com sg home php Regions Covered Singapore 97 7 Appendix NEC Corporation of Malaysia Sdn Bhd Address 33rd Floor Menara TA One 22 Jalan P Ramlee 50250 Kuala Lumpur Malaysia Telephone 6 03
28. This is the default setting 10096 Off O LAMP Brightness O STATUS ECO Select this mode to increase the Steady Green light OL LAMP lamp life approx 70 Brightness O STATUS on NP600 NP500W NP600S NP500WS and approx 80 Bright ness on NP500 NP400 NP300 To change to the ECO mode do the following 1 Press the LAMP MODE button on the remote control to display LAMP MODE screen 2 Use the SELECT A or Y button to select ECO mode 3 Press the ENTER button To change from ECO to NORMAL Go back to Step 2 and select NORMAL Repeat Step 3 NOTE The LAMP MODE can be changed by using the menu Select SETUP GENERAL LAMP The lamp life remaining and lamp hours used can be checked in USAGE TIME Select INFO USAGE TIME The projector is always in NORMAL for one minute after the lamp is turned on and while the POWER indicator is blinking green The lamp condition will not be affected even when LAMP MODE is changed After a lapse of 3 minutes from when the projector displays a blue black or logo screen LAMP MODE will automatically switch to ECO The projector will return to the NORMAL once a signal is accepted If the projector is overheated in NORMAL mode there may be a case where the LAMP MODE automatically changes to ECO mode to protect the projector When the projector is in ECO mode the picture brightness decreases When the projector comes back to norm
29. When the incoming signal with the resolution of 800 x 600 is displayed on the NP500W NP500WS NOTE e When a non computer signal is displayed the NATIVE is not available e When a signal with a higher resolution than the projector s native resolution is displayed NA TIVE is not available 60 5 Using On Screen Menu Sample image when the appropriate aspect ratio is automatically determined NP600 NP500 NP400 NP300 NP600S Computer signal Aspect ratio of incoming signal 4 3 16 10 Sample image when the appro priate aspect ratio is automati cally determined oy Video signal Aspect ratio of incoming signal Sample image when the as pect ratio is automatically de termined NOTE To display a squeezed signal prop erly select 16 9 or WIDE ZOOM NP500W NP500WS Computer signal Aspect ratio of incoming signal Sample image when the appro priate aspect ratio is automati cally determined Video signal Aspect ratio of incoming signal Sample image when the as pect ratio is automatically de termined NOTE To display a letterbox signal prop erly select LETTERBOX NOTE To display a squeezed signal prop erly select 16 9 TIP e Image position can be adjusted vertically using POSITION when the 16 9 15 9 or 16 10 aspect ratios are selected gt next page
30. be checked in USAGE TIME Select INFO USAGE TIME gt page 73 The projector is always in NORMAL for one minute after the lamp is turned on and while the POWER indicator is blinking green The lamp condition will not be affected even when LAMP MODE is changed If there is no signal for about one minute the projector will display a blue black or logo background depending on setting and go into ECO The projector will return to the NORMAL mode once a signal is accepted If the projector becomes overheated in NORMAL mode because of use in a high temperature room there may be a case where the LAMP MODE automatically changes to ECO mode to protect the projector This mode is called forced ECO mode When the projector is in ECO mode the picture brightness decreases The LAMP indicator s steady light indicates the projector is in ECO mode When the projector comes back to normal temperature the LAMP MODE returns to NORMAL mode Thermometer symbol i indicates the LAMP MODE is automatically set to ECO mode because the internal temperature is too high 64 5 Using On Screen Menu Setting Closed Caption CLOSED CAPTION This option sets several closed caption modes that allow text to be superimposed on the projected image of Video or S Video This exits the closed caption mode CAPTION 1 4 Text is superimposed TEXT 1 4 Text is displayed NOTE The clos
31. be in accordance with any local building codes Please consult your dealer for more information Features you ll enjoy e Quick start amp Direct Power Off Eight seconds after turning on the power the projector is ready to display PC or video images The projector has a feature called Direct Power Off This feature allows the projector to be turned off even when projecting an image using a power strip equipped with a switch and a breaker AUTO POWER ON and AUTO POWER OFF features The AUTO POWER ON AC AUTO POWER ON COMP1 AUTO POWER OFF and OFF TIMER features eliminate the need to always use the POWER button on the remote control or projector cabinet Short throw distances NP600S NP500WS Short focal lenses provide for a larger image using a shorter throw distance when compared to a typical projector lens Virtual Remote function The Virtual Remote function allows power On Off and source selection of the projector from your PC by using the supplied VGA signal cable The utility software Virtual Remote Tool exclusively for the projector is required to be downloaded from our website The optional remote control NPO2RC allows you to assign a CONTROL ID to the projector Multiple projectors can be operated separately and independently with the same single remote control by assigning an ID number to each projector A variety of input ports and a comprehensive array of system control interfaces This projector supports
32. exceeds 3100 hours up to 4100 hours Eco mode If so replace the lamp After replacing the lamp reset the lamp hours used page 75 The lamp may fail to light Wait a full minute and then turn on the power again Set FAN MODE to HIGH ALTITUDE when using the projector at altitudes approximately 5500 feet 1600 meters or higher Using the projector at altitudes approximately 5500 feet 1600 meters or higher without setting to HIGH ALTITUDE can cause the projector to overheat and the projector could shut down If this happens wait a couple minutes and turn on the projector page 69 Also when the lamp is turned off the projector internal temperature is hot If the power is turned on before the projector has cooled down the fan will run a short time before the lamp will turn on Ensure that the OFF TIMER or AUTO POWER OFF is off page 71 72 e Use the COMPUTER1 the COMPUTER2 the VIDEO or the S VIDEO button on the remote control to select your source Computer Video or S Video page 29 If there is still no picture press the button again Ensure your cables are connected properly Use menus to adjust the brightness and contrast page 57 Remove the lens cap Resetthe settings or adjustments to factory preset levels using the RESET in the Menu page 75 Enter your registered keyword if the Security function is enabled page 42 sure to connect the projector and notebook PC
33. page 16 13 2 Installation and Connections NP500WS The further your projector is from the screen or wall the larger the image The minimum size the image can be is ap proximately 57 1 45m measured diagonally when the projector is roughly 36 inches 0 9 m from the wall or screen The largest the image can be is 104 2 6m when the projector is about 66 inches 1 7 m from the wall or screen Screen Size Unit cm inch 224 0 W x 140 0 H 88 W x 55 H Screen Size Grace 108 1 193 9 W x 121 2 H 76 W x 48 H So 8 172 1 gt 42H PE 70 129 2 W x 80 8 H 51 W x 32 H 122 8 W x76 7 H 48 W x 30 H SON X QS TIP Digital Zoom can result in a blurry image due to the electronic zoom The Digital Zoom function adjusts the image size by up to 20 page 32 For more details on throw distance see page 16 14 Throw Distance and Screen Size The following shows the proper relative positions of the projector and screen Refer to the table to determine the position of installation Distance Chart NP600 NP500 NP400 NP300 NP500W Screen center Lens center 2 Installation and Connections Vertical distance between lens center and Screen center Throw distance D Vertical distance between lens center and screen bottom top of screen
34. s manual however should you notice any questionable points errors or omissions please contact us 4 Notwithstanding article 3 NEC will not be responsible for any claims on loss of profit or other matters deemed to result from using the Projector Important Information Safety Cautions Precautions Please read this manual carefully before using your NEC NP600 NP500 NP400 NP300 NP500W 6005 NP500WS projector and keep the manual handy for future reference CAUTION To turn off main power be sure to remove the plug from power outlet The power outlet socket should be installed as near to the equipment as possible and should be easily accessible CAUTION TO PREVENT SHOCK DO NOT OPEN THE CABINET A THERE ARE HIGH VOLTAGE COMPONENTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL shock Therefore it is dangerous to make any kind of contact with any part inside of the unit This symbol alerts the user that important information concerning the operation and maintenance of this unit has been provided f This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical The information should be read carefully to avoid problems WARNING TO PREVENT FIRE OR SHOCK DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE DO NOT USE THIS UNIT S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALL THE PRONGS CAN BE FULLY INSERTED DOC Compliance Notice for Canada
35. sure that the lamp housing is cool enough to before removing it Interlock 80 6 Maintenance 3 Install a new lamp housing 1 Insert a new lamp housing until the lamp housing is plugged into the socket CAUTION Do not use a lamp other than the NEC replacement lamp NPO7LP Order this from your NEC dealer 2 Push the top center of the lamp housing to secure it 3 Secure it in place with the two screws Be sure to tighten the screws 4 Reattach the lamp cover 1 Slide the lamp cover back until it snaps into place 2 Tighten the screw to secure the lamp cover Be sure to tighten the screw 5 Connect the supplied power cable turn on the Main Power switch and turn on the projector 6 Finally select the menu RESET gt CLEAR LAMP HOURS to reset the lamp usage hours NOTE When you continue to use the projector for another 100 hours after the lamp has reached the end of its life the projector cannot turn on and the menu is not displayed If this happens press the HELP button on the remote control for 10 seconds to reset the lamp clock back to zero When the lamp time clock is reset to zero the LAMP indicator goes out 81 7 Appendix Troubleshooting This section helps you resolve problems you may encounter while setting up or using the projector Indicator Messages Power Indicator Indicator Condition Projector Condition Note Off The ma
36. the level or turn the selected item on or off by using the SELECT AY 4b buttons on the remote control or the projector cabinet Changes are stored until adjusted again 7 Repeat steps 2 6 to adjust an additional item or press the EXIT button on the remote control or the projec tor cabinet to quit the menu display NOTE When a menu or message is displayed several lines of information may be lost depending on the signal or settings 8 Press the MENU button to close the menu To return to the previous menu press the EXIT button 51 5 Using On Screen Menu Menu Elements Tab Slide bar SOURCE SETUP INFO PRESET 2 PRESENTATION T 3 Solid triangle DETAIL SETTINGS CONTRAST e BRIGHTNESS X SHARPNESS 3 RESET m Available buttons ENTER EXIT Source COMPUTERI Highlight ADJUST SETUP INFO RESET Radio button COMPUTER COMPUTER2 DIGITAL WALL COLCR COMPUTER2 ANALOG VIDEO Nd XE O S VIDEO O WHITEBOARD BLACKBOARD BLACKBOARD GRAY LIGHT YELLOW M LIGHT GREEN M LIGHT BLUE a SKYBLUE C COMPUTER LIGHT ROSE High Altitude symbol PINK Thermometer symbol Off Timer remaining time Key Lock symbol Menu windows or dialog boxes typically have the following elements Highlight cus Indicates the selected menu or item Solid triangle Indicates further choices are available A highlighte
37. the power cable or plug is damaged or frayed If liquid has been spilled into the projector or if it has been exposed to rain or water If the projector does not operate normally when you follow the instructions described in this user s manual f the projector has been dropped or the cabinet has been damaged f the projector exhibits a distinct change in performance indicating a need for service Disconnect the power cable and any other cables before carrying the projector Turn off the projector and unplug the power cable before cleaning the cabinet or replacing the lamp Turn off the projector and unplug the power cable if the projector is not to be used for an extended period of time When using a LAN cable For safety do not connect to the connector for peripheral device wiring that might have excessive voltage CAUTION e not use the tilt foot for purposes other than originally intended Misuses such as gripping the tilt foot or hang ing on the wall can cause damage to the projector Do not send the projector in the soft case by parcel delivery service or cargo shipment The projector inside the Soft case could be damaged Select HIGH in Fan mode if you continue to use the projector for consecutive days From the menu select SETUP OPTIONS 1 FAN MODE HIGH Do not try to touch the ventilation outlet on the left front when seen from the front as it can become heated while the projector is turned on an
38. turn off the main power switch and unplug the projector before replacing the filters e Only clean the outside of the filter cover with a vacuum cleaner e Do not attempt to operate the projector without the filter cover To clean the air filter Vacuum the filter through the filter cover To replace the filter sponge 1 Remove the filter cover 2 locations by pushing up on the catch of the cover until you feel it detach 2 Replace two filters 1 Gently peel off the filter sponge and clean the filter cover 2 Attach the new filter to the filter cover 76 6 Maintenance 3 Reinstall the new filter cover 2 locations Insert the filter cover until you feel click 4 Clear the filter hours used To reset the filter usage time from the menu select RESET CLEAR FILTER HOURS page 75 for resetting the filter usage time NOTE Do not wash the filter with soap and water Soap and water will damage the filter membrane Before replacing the filter remove dust and dirt from the projector cabinet Keep out dust and dirt during filter replacement NOTE When you replace the lamp it is also wise to replace the filter The filter comes in the same package with your replacement lamp 77 6 Maintenance Cleaning the Cabinet and the Lens 1 Turn off the projector before cleaning 2 Clean the cabinet periodically with a damp cloth If heavily soiled use a mild detergent Never use str
39. 015 For North America only Registration card Limited warranty For customers in Europe Quick Setup Guide CD ROM You will find our current valid Guar 7N8P9291 User s manual antee Policy on our Web Site Important Information 7N951301 www nec display solutions com 7N8P9301 DVI to VGA adapter 7N960234 Unless otherwise described in the user s manual the drawings for the projector cabinet show examples of the NP600 1 1 Introduction Q Introduction to the Projector This section introduces you to your new projector and describes the features and controls Congratulations on Your Purchase of the Projector This projector is one of the very best projectors available today The projector enables you to project precise images up to 300 inches 110 inches on NP600S 104 inches on NP500WS across measured diagonally from your PC or Macintosh computer desktop or notebook VCR DVD player or document camera You can use the projector on a tabletop or cart you can use the projector to project images from behind the screen and the projector can be permanently mounted on a ceiling The remote control can be used wirelessly 1 Do not attempt to mount the projector on a ceiling yourself The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk of bodily injury In addition the ceiling must be strong enough to support the projector and the installation must
40. 1 Introduction 1 Introduction Terminal Panel Features ENEON e d q 882 000000 87 00 1 COMPUTER 1 IN Component Input Connector Mini D Sub 15 Pin page 17 20 22 2 COMPUTER 2 DVI I IN Connector 29 Pin HDCP compatible page 19 20 3 AUDIO IN Mini Jack Stereo Mini page 17 19 22 4 AUDIO OUT Mini Jack Stereo Mini page 21 5 MONITOR OUT COMP 1 Connector Mini D Sub 15 Pin page 21 6 S VIDEO IN Connector Mini DIN 4 Pin page 23 7 VIDEO IN Connector RCA page 23 8 AUDIO Input Jacks L R RCA page 23 9 PC CONTROL PC CONTROL Port D Sub 9 Pin page 93 Use this port to connect a PC or control system This enables you to control the projector using serial communication protocol If you are writing your own program typical PC control codes are on page 93 10 LAN Port RJ 45 page 24 1 Introduction Q Part Names of the Remote Control 3eme 2 A CO A 4 9I esi 6 C DOWN On 9 6 L CLICK R CLICK 11 _ C 3 12 13 O QC 16 1 5 SET LE 1 9 VOLUME ASPECT HELP C QC 22 L m 1 Infrared Transmitter page 10 2 POWER ON Button page 27 3 POWER OFF Button page 38 4 MAGNIFY Button page 40 5 PIC MUTE Button page 40 6 PAGE UP DOWN Button
41. 2178 3600 ISDN Fax Line 6 03 2178 3789 Email Address necare Qnsm nec co jp WEB Address http www necarecenter com Regions Covered Malaysia Hyosung ITX Co Ltd Address 1st FI Ire B D 2 4Ga Yangpyeng Dong Youngdeungpo Gu Seoul Korea 150 967 Telephone 82 2 2163 4193 Fax Line 482 2 2163 4196 Email Address hyosung com Regions Covered South Korea Lenso Communication Co Ltd Address 292 Lenso House 4 1st Floor Srinakarin Road Huamark Bangkapi Bangkok 10240 Thailand Telephone 66 2 375 2425 Fax Line 66 2 375 2434 Email Address pattara lenso com WEB Address http www lensocom com Regions Covered Thailand ABBA Electronics L L C Address Tariq Bin Ziyad Road P O Box 327 Dubai United Arab Emirates Telephone 971 4 371800 Fax Line 971 4 364283 Email Address Regions Covered United Arab Emirates Samir Photographic Supplies Address P O Box 599 Jeddah 21421 Saudi Arabia Telephone 966 2 6828219 Fax Line 966 2 6830820 Email Address asif samir photo com Riyadh Address P O Box 5519 Riyadh 11432 Saudi Arabia Telephone 966 1 4645064 Fax Line 966 1 4657912 Email Address bhimji samir photo com Alkhobar Address P O Box 238 Alkhobar 31952 Saudi Arabia Telephone 966 3 8942674 Fax Line 966 3 8948162 Email Address chamsedin 9 samir photo com Regions Covered Saudi Arabi
42. 3 MINUTES message will be displayed on the bottom of the screen Selecting Power saving in SSTANDBY MODE The projector has two standby modes NORMAL and POWER SAVING The POWER SAVING mode is the mode that allows you to put the projector in the power saving condition which consumes less power than the NORMAL mode The projector is preset for NORMAL mode at the factory NORMAL Power indicator Orange light STATUS indicator Green light POWER SAVING Power indicator Orange light STATUS indicator Off The following connectors buttons or functions will not work during this mode PC CONTROL port MONITOR OUT connector and AUDIO OUT connector LAN Mail Alert AUTO POWER ON COMP1 functions Buttons other than POWER button on the cabinet Buttons other than POWER ON button on the remote control Virtual Remote function NOTE Your setting will not be affected even when RESET is done from the menu Enabling Auto Power On AUTO POWER ON AC Turns the projector on automatically when the power cable is inserted into an active power outlet This eliminates the need to always use the POWER button on the remote control or projector cabinet 71 5 Using On Screen Menu Turning On the Projector By Applying Computer Signal AUTO POWER ON COMP1 When the projector is in Standby mode applying a computer signal from a computer connected to the COMPUTER1 IN input will power on the projector and simult
43. 33 Remote sensor page 10 Lens Built in Security Slot Ventilation inlet Filter Cover gt page 76 Lens Cap This security slot supports the MicroSaver Security System Adjustable Tilt Foot Lever page 31 Adjustable Tilt Foot page 31 1 Introduction Rear Lamp Cover page 80 Monaural Speaker 7W Ventilation inlet Filter Cover gt page 76 Ventilation outlet Terminal Panel gt page 8 Heated air is exhausted from here Spacer black rubber To fine adjust the height of the rear foot remove the spacer and rotate the rear foot to the desired height Rear Foot page 31 AC Input Connect the supplied power cable s two pin plug here and plug the other end into an active wall outlet page 25 Main Power Switch When you plug the supplied power cable into an active wall outlet and turn on the Main Power the POWER indicator turns orange and the projector is in standby mode gt page 26 38 Top Features O qe cs 9 7 8 9 P 10 12 5 6 POWER Button 27 38 POWER Indicator 26 38 82 STATUS Indicator page 82 LAMP Indicator 79 82 SOURCE Button 29 AUTO ADJ Button page 37 MENU Button 51 SELECT AY lt P gt Volume Buttons lt gt Keystone Buttons 34 37 ENTER Button 51 10 EXIT Button 51
44. 34 178 4523 111 2827 39 989 243 6169 E 293 7442 17 424 9 1 7 6 240 6096 204 5169 127 3281 45 1181 278 7056 335 8510 19 485 9 1 7 6 270 6858 229 5816 143 3635 50 1272 313 7942 E 377 9578 21 545 9 1 7 6 300 7620 254 6462 159 4039 56 1414 348 8829 419 10646 24 606 9 1 7 6 15 Distance Chart NP600S NP500WS 2 Installation and Connections B Vertical distance between lens center and Screen center Screen center C Throw distance D Vertical distance between lens center and screen bottom top of screen for ceiling ap plication Throw angle D Es 1 d NOTE The values in the tables are design values and Screen bottom m ay vary NP600S Screen Size B C D a Diagonal Width Height wide wide inch mm inch mm inch mm inch mm inch mm inch mm degree 60 1524 48 1219 36 914 20 505 35 895 2 48 294 64 1626 51 1300 38 975 21 538 38 956 2 51 29 4 70 1778 56 1422 42 1067 23 589 41 1049 2 56 293 77 1956 62 1565 46 1173 26 648 46 1156 2 61 29 3 80 2032 64 1626 48 1219 27 673 47 1203 3 64 292 90 2286 72 1829 54 1372 30 757 53 1357 3 71 29 2 100 2540 80 2032 60 1524 33 841 59 1511 3 79 294 110 2794 88 2235 66 1676 36 926 66 1665 3 87 29 1 NP500WS Screen Size B
45. 4 inches 9 7 m from the wall or Screen Screen Size Unit cm inch 646 2 W x 403 9 254 W x 159 H 516 9 W x 323 1 H 204 W x 127 H 430 8 W x 269 2 H 170 W x 106 H 387 7 W x 242 3 H 153 W x 95 H 323 1 W x 201 9 H 127 W x 79 H 258 5 W x 161 5 H 102 W x 64 H 215 4 W x 134 6 H 85 W x 53 H 172 3 W x 107 7 H 68 W x 42 H 129 2 W x 80 8 H 51 W x 32 H TIP The distances are indicated by intermediate values between tele and wide Use as a rule of thumb The Zoom lever adjusts the image size by up to 10 For more details on throw distance see page 15 12 2 Installation and Connections NP600S The further your projector is from the screen or wall the larger the image The minimum size the image can be is ap proximately 60 1 52m measured diagonally when the projector is roughly 35 inches 0 9 m from the wall or screen The largest the image can be is 110 2 8 m when the projector is about 66 inches 1 7 m from the wall or screen Screen Size Unit cm inch 223 5 W x 167 6 H 88 W x 66 H Screen Size TIP Digital Zoom can result in a blurry image due to the electronic zoom The Digital Zoom function adjusts the image size by up to 20 page 32 For more details on throw distance see
46. 58 6555 310 7878 20 500 9 5 7 9 240 6096 192 4877 144 3658 50 1257 295 7497 355 9009 23 572 9 5 7 9 270 6858 216 5486 162 4115 56 1414 332 8439 399 10140 25 643 9 5 7 9 300 7620 240 6096 180 4572 62 1572 369 9381 444 1271 28 714 9 5 7 9 NP500W Screen Size B C D Diagonal Width Height wide tele wide tele inch mm inch mm inch mm inch mm inch mm inch mm inch mm degree degree 21 533 18 452 11 283 4 99 28 712 2 42 7 9 25 635 21 538 13 337 5 118 28 703 34 854 2 50 9 5 79 30 762 25 646 16 404 6 141 34 851 41 1032 2 61 9 4 7 8 40 1016 34 862 21 538 7 188 45 1146 55 1389 3 81 9 3 73 60 1524 51 1292 32 808 11 283 68 1737 83 2101 5 121 9 2 77 72 1829 61 1551 38 969 13 339 82 2092 100 2528 6 145 9 2 7 6 80 2032 68 1723 42 1077 15 377 92 2328 111 2813 6 162 92 7 6 84 2134 71 1809 45 1131 16 396 96 2446 116 2955 7 170 92 7 6 90 2286 76 1939 48 1212 17 424 103 2624 125 3169 7 182 9 2 7 6 100 2540 85 2154 53 1346 19 471 115 2919 139 3525 8 202 92 7 6 120 3048 102 2585 64 1615 22 565 138 3510 167 4237 10 242 92 7 6 150 3810 127 3281 79 2019 28 707 173 4396 209 5305 12 303 9 1 7 6 180 4572 153 3877 95 2423 33 848 208 5283 251 6374 14 363 9 1 7 6 200 5080 170 4308 106 2692 37 942 231 5874 279 7086 16 404 9 1 7 6 210 53
47. C D a Diagonal Width Height wide wide inch mm inch mm inch mm inch mm inch mm inch mm degree 57 1448 48 1228 30 767 20 508 36 902 5 125 294 60 1524 51 1292 32 808 21 535 37 951 5 131 29 4 70 1778 59 1508 37 942 25 624 44 1114 6 153 293 80 2032 68 1723 42 1077 28 713 50 1277 7 175 292 87 2210 74 1874 46 1171 31 716 55 1392 190 29 1 90 2286 76 1939 48 1212 32 803 57 1441 8 197 291 100 2540 85 2154 53 1346 35 892 63 1604 9 219 291 104 2642 88 2240 55 1400 37 928 66 1669 9 228 291 WARNING Installing your projector on the ceiling must be done by a qualified technician Contact your NEC dealer for more information Do not attempt to install the projector yourself Only use your projector on a solid level surface If the projector falls to the ground you can be injured and the projector severely damaged Do not use the projector where temperatures vary greatly The projector must be used at temperatures between 41 F 5 C 104 F 40 C Eco mode se lected automatically at 95 F to 104 F 35 C to 40 C Do not expose the projector to moisture dust or smoke This will harm the screen image Ensure that you have adequate ventilation around your projector so heat can dissipate Do not cover the vents on the side or the front of the projector Reflecting the Image Using a mirror to reflect your projector s im
48. DESKTOP REAR ORIENTATION FRONT CEILING FRONT CONTROL PANEL LOCK OFF OFF ON SECURITY OFF OFF ON INSTALLATION COMMUNICATION SPEED 19200bps 4800bps 9600bps 19200bps CONTROL ID 1 1 254 CONTROL ID NUMBER CONTROL ID OFF OFF ON AUTO ADJUST NORMAL OFF NORMAL FINE FAN MODE AUTO AUTO HIGH HIGH ALTITUDE RGB COMPUTER1 COMPONENT RGB COMPONENT RGB COMPONENT COMPUTER2 RGB SIGNAL ANALOG COMPONENT RGB COMPONENT RGB COMPONENT SELECT VIDEO AUTO AUTO NTSC3 58 NTSC4 43 PAL PAL M PAL N SETUP PAL60 SECAM OPTIONS 1 S VIDEO AUTO AUTO NTSC3 58 NTSC4 43 PAL PAL M PAL N PAL60 SECAM NP600 NP500 NP400 NP300 WXGA MODE NP600S OFF OFF ON NP500W NP500WS ON DEINTERLACE ON OFF ON BEEP ON OFF ON OFF TIMER OFF OFF 0 30 1 00 2 00 4 00 8 00 12 00 16 00 STANDBY MODE NORMAL NORMAL POWER SAVING AUTO POWER ON AC OFF OFF ON OPTIONS 2 AUTO POWER ON COMP1 OFF OFF ON AUTO POWER OFF OFF OFF 0 05 0 10 0 20 0 30 LAST AUTO COMPUTER1 COMPUTER2 DIGITAL DEFAULT SOURCE SELECT EAST COMPUTER2 ANALOG VIDEO S VIDEO LAMP LIFE REMAINING USAGE TIME LAMP HOURS USED FILTER HOURS USED SOURCE INDEX HORIZONTAL FREQUENCY VERTICAL FREQUENCY SIGNAL TYPE SOURCE VIDEO TYPE SYNC TYPE INFO SYNC POLARITY SCAN TYPE PROJECTOR NAME MAC ADDRESS PRODUCT SERIAL NUMBER FIRMWARE VERSION DATA CONTROL ID when CONTROL ID is set CURRENT SIGNAL ALL DATA RESET NETWORK SETTINGS CLEAR LAMP HOURS CLEAR FILTER HOURS
49. EC 155 6020 switcher NOTE An image may not be displayed correctly when a Video or S Video source is played back via a commercially available scan converter This is because the projector will process a video signal as a computer signal at the default setting In that case do the following When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly Project an image to fill the screen and then press the AUTO ADJ button on the remote control or the projector cabinet 18 2 Installation and Connections When Viewing a DVI Digital Signal To project a DVI digital signal be sure to connect the PC and the projector using a DVI cable not supplied before turning on your PC or projector Turn on the projector first and select Computer 2 Digital from the source menu before turning on your PC Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed Should this happen restart your PC Do not disconnect the DVI cable while the projector is running If the signal cable has been disconnected and then re connected an image may not be correctly displayed Should this happen restart your PC NOTE Use a DVI cable or the one compliant with the DDWG Digital Display Working Group DVI Digital Visual Interface revision 1 0 standard The DVI cable should be within 5 m 196 long Both single and dual types of DVI
50. For PC the mouse receiver can only be used with a Windows 98 Me XP Windows 2000 Windows Vista or Mac OS X 10 0 0 or later operating system NOTE In SP1 or older version of Windows XP if the mouse cursor will not move correctly do the following Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box Pointer Options tab NOTE Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa The computer may not identify the mouse receiver if it is repeatedly connected and disconnected in rapid intervals 45 4 Convenient Features Operating your computer s mouse from the remote control You can operate your computer s mouse from the remote control PAGE UP DOWN Button scrolls the viewing area of the window or to move to the previous or next slide in Power Point on your computer SELECTA Y 4b Buttons moves the mouse cursor on your computer MOUSE L CLICK Button works as the mouse left button MOUSE R CLICK Button works as the mouse right button NOTE e When you operate the computer using the SELECT AW button with the menu displayed both the menu and the mouse pointer will be affected Close the menu and perform the mouse operation The PAGE UP and DOWN buttons do not work with PowerPoint for Macintosh About Drag Mode By pressing the MOUSE L CLICK or R CLICK button for 2 or 3 seconds then rel
51. IOIN Component video RCA x 3 Y L R cable not supplied L eu DVD player f AA L R Y Cb Cr Audio cable not supplied gt AUDIO Component A component signal will be automatically displayed If not from the menu select SETUP OPTIONS 1 gt SIGNAL SELECT COMPUTER1 and then place a check mark in the Component radio button Select the source name for its appropriate input connector after turning on the projector SOURCE button on the projector cabinet COMPUTER 1 IN COMPUTER 1 COMPUTER 1 Input connector Button on the remote control NOTE Refer to your DVD player s owner s manual for more information about your DVD player s video output requirements 22 2 Installation and Connections Connecting Your VCR S VIDEO IN AUDIO INN VIDEO IN Mr Ce ug S Video cable not supplied Audio cable not supplied Video cable not supplied Audio equipment VCR VIDEO S VIDEO co VIDEOOUT Audio cable not supplied ang A a LM d Select the source name for its appropriate input connector after turning on the projector Input connector SCURGE
52. M lever to adjust the image size on the screen NP600S NP500WS The image size can be adjusted electronically from the menu To do so follow the steps below 1 Press the MENU button The menu will be displayed 2 Press the SELECT gt button to select SETUP and press the ENTER button The GENERAL tab will be highlighted SOURCE ADJUST INFO RESET DIGITAL ZOOM a 100 AUTO KEYSTONE OFF KEYSTONE ap KEYSTONE SAVE OFF WALL COLOR OFF LAMP MODE NORMAL CLOSED CAPTION OFF LANGUAGE ff ENGLISH ENTER EXIT CJ COMPUTER 3 Press the SELECT Y button The DIGITAL ZOOM will be highlighted SOURCE ADJUST INFO RESET Li AUTO KEYSTONE OFF KEYSTONE ap KEYSTONE SAVE OFF WALL COLOR OFF LAMP MODE NORMAL CLOSED CAPTION OFF LANGUAGE ff ENGLISH ENTER EXIT CJ COMPUTER1 3 Projecting an Image Basic Operation 4 Use the SELECT 4 or gt button to adjust the image size 5 After completing adjustment press the EXIT button three times The menu will be closed Focus NP600 NP500 NP400 NP300 NP500W Use the FOCUS ring to obtain the best focus oui omm p NP600S NP500WS Use the FOCUS lever to obtain the best focus 33 3 Projecting an Image Basic Operation Q Correcting Keystone Distortion Correcting Keystone Distortion If the screen is tilted vertically keystone distortion becomes large Proceed with the following steps to corr
53. NE SOURCE ADJUST INFO RESET AUTO KEYSTONE OFF KEYSTONE SAVE OFF WALL COLOR OFF LAMP MODE NORMAL CLOSED CAPTION OFF LANGUAGE ENGLISH ENTER EXIT CJ COMPUTER 4 Press the SELECT 4 or button Adjust so that the image is rectangular 5 Press the MENU button The menu will be closed NOTE The Keystone correction can cause an image to be slightly blurred because the correction is made electronically TIP The changes can be saved with KEYSTONE SAVE page 36 63 35 3 Projecting an Image Basic Operation Adjusting with the Auto Keystone Function The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen No special operation required Just put the projector on a flat surface TIP Even when the menu setting for AUTO KEYSTONE is turned on KEYSTONE can be adjusted manually To turn on AUTO KEYSTONE proceed the following steps 1 Press the MENU button The menu will be displayed 2 Press the SELECT gt button to select SETUP and press the ENTER button The GENERAL screen will be highlighted 3 Press the SELECT Y button The AUTO KEYSTONE will be highlighted SOURCE ADJUST KEYSTONE 4 gt KEYSTONE SAVE OFF WALL COLOR OFF LAMP MODE NORMAL CLOSED CAPTION OFF LANGUAGE ENGLISH _ D SELECT MD EXIT 4 Press the ENTER button to display the AUTO
54. Normal m Blinking light Red Lamp has reached its end of life Lamp re Replace the lamp placement message will be displayed Steady light Red Lamp has been used beyond its limit The Replace the lamp projector will not turn on until the lamp is replaced Green Lamp mode is set to Eco mode If the temperature inside the projector rises too high the over temperature protector will automatically turn off the lamp with the STATUS indicator blinking 2 cycle On and Off Should this happen do the following Unplug the power cable after the cooling fans stop Move the projector to a cooler location if the room where you are presenting is particularly too warm Clean the ventilation holes if they are clogged with dust Wait about 60 minutes until the inside of the projector becomes cool enough 82 7 Appendix Common Problems amp Solutions Power Status Lamp Indicator on page 82 Check These Items Problem Does not turn on or shut down Will turn off No picture Check that the power cable is plugged in and that the power button on the projector cabinet or the remote control is on pages 25 and 38 Ensure that the lamp cover is installed correctly page 81 Check to see if the projector has overheated If there is insufficient ventilation around the projector or if the room where you are presenting is particularly warm move the projector to a cooler location Check to see if the lamp usage
55. O PORTUGUES D T RK E S Ly FRANCAIS E TINA gt ITALIANO MAGYAR 235 ESPANOL POLSKI EAAHNIKA SVENSKA NEDERLANDS mx SUOMI 0 CESET NCUS EXIT SELECT SELECT 2 Press the ENTER button to execute the selection After this has been done you can proceed to the menu operation If you want you can select the menu language later LANGUAGE on page 53 and 65 NOTE Immediately after turning on the projector screen flicker may occur This is normal Wait 3 to 5 minutes until the lamp light ing is stabilized NOTE If you turn on the projector immediately after the lamp is turned off or when the temperature is high the fans run without displaying an image for some time and then the projector will display the image A CAUTION The projector cannot be turned off for 60 seconds after the lamp is turned on and while the POWER indicator is blinking green Doing so could cause premature lamp failure When the LAMP MODE is set to ECO the LAMP indicator will light green If one of the following things happens the projector will not turn on f the internal temperature of the projector is too high the projector detects abnormal high temperature In this condition the projector will not turn on to protect the internal system If this happens wait for the projector s internal components to cool down When the lamp reaches its end of usable life the projector w
56. OMPUTER2 DIGITAL COMPUTER2 ANALOG VIDEO gt S VIDEO COMPUTER gt TIP If no input signal is present the input will be skipped Using the Remote Control Press any one of the COMPUTER 1 2 VIDEO and S VIDEO buttons TIP The COMPUTER 2 button on the remote control toggles the Computer 2 source between COMPUTER2 DIGITAL and COMPUTER2 ANALOG Selecting Default Source You can set a source as the default source so that it will be displayed each time the projector is turned on 1 Press the MENU button The menu will be displayed 2 Press the SELECT button twice to select SETUP and press the SELECT Y button or the ENTER button to select GENERAL 3 Press the SELECT gt button three times to select OPTIONS 2 4 Press the SELECT Y button six times to select DEFAULT SOURCE SELECT and press the ENTER button The DEFAULT SOURCE SELECT screen will be displayed gt page 72 5 Select a source as the default source and press the ENTER but ton 6 Press the EXIT button a few times to close the menu 7 Restart the projector The source you selected in step 5 will be projected TIP When the projector is in Standby mode applying a computer signal from a computer connected to the COMPUTER 1 IN input will power on the projector and simultaneously project the computer s image AUTO POWER ON COMP1 page 72 29 D O LAMP O STATUS ITO ADJ COMPUTER1 COMPUTE
57. OVERSCAN O 96 Ca ASPECT RATIO AUTO Tr VIDEO FILTER OFF GT COMPUTER Adjusting Clock and Phase CLOCK PHASE This allows you to manually adjust CLOCK and PHASE Hn E CLOCK Use this item to fine tune the computer image or to remove any vertical banding that might appear This function adjusts the clock frequencies that eliminate the horizontal banding in the image This adjustment may be necessary when you connect your computer for the first time PHASE Use this item to adjust the clock phase or to reduce video noise dot interference or cross talk This is evident when part of your image appears to be shimmering Use PHASE only after the CLOCK is complete mui eo oy 58 5 Using On Screen Menu Adjusting Horizontal Vertical Position HORIZONTAL VERTICAL Adjusts the image location horizontally and vertically FE
58. R2 DIGITAL COMPUTER2 ANALOG VIDEO S VIDEO co SOURCE ADJUST gt OFF TIMER OFF STANDBY MODE NORMAL AUTO POWER ON AC OFF AUTO POWER ON COMP1 OFF AUTO POWER OFF OFF LAST MOVE XGULX SELECT COMPUTERT DEFAULT SOURCE SELECT LAST O AUTO COMPUTER COMPUTER2 DIGITAL O COMPUTER2 ANALOG VIDEO S VIDEO L ENTER J cD 3 Projecting an Image Basic Operation Adjusting the Picture Size and Position Use the adjustable tilt foot the zoom function or the focus ring to adjust the picture size and position In this chapter drawings and cables are omitted for clarity Adjusting the throw angle the height of an image Adjusting the left and right tilt of an image Tilt foot page 31 Rear foot page 31 LRL n Finely adjusting the size of an image Adjusting the focus Zoom function page 32 Focus ring page 33 Adjusting the keystone correction KEYSTONE page 34 Keystone correction can be also performed automatically page 36 30 3 Projecting an Image Basic Operation Adjust the Tilt Foot 1 Lift the front edge of the projector CAUTION Do not try to touch the ventilation outlet during Tilt Foot adjustment as it can become heated while the projector is turned on and during its cool down period after it is turned off
59. RESENTATION or HIGH BRIGHT is selected in REFERENCE this function is not available Adjusting White Balance WHITE BALANCE This allows you to adjust the white balance Contrast for each color RGB to adjust the white level of the screen Brightness for each color RGB is used to adjust the black level of the screen CONTRAST Adjusts the intensity of the image according to the incoming signal BRIGHTNESS Adjusts the brightness level or the back raster intensity SHARPNESS Controls the detail of the image COLOR Increases or decreases the color saturation level HUE Varies the color level from green to blue The red level is used as reference Input signal CONTRAST BRIGHTNESS SHARPNESS COLOR HUE Computer RGB DIGITAL Yes Yes Yes No No Computer RGB ANALOG Yes Yes Yes No No Component Yes Yes Yes Yes Yes Video S Video Yes Yes Yes Yes Yes Yes Adjustable No Not adjustable Yes depending on the signal 57 5 Using On Screen Menu RESET The settings and adjustments for PICTURE will be returned to the factory settings with the exception of the following Preset numbers and REFERENCE within the PRESET screen The settings and adjustments under DETAIL SETTINGS within the PRESET screen that are not currently selected will not be reset IMAGE OPTIONS SOURCE SETUP INFO RESET CLOCK 1344 GT PHASE J e HORIZONTAL _ ED VERTICAL _ E
60. SENDER S ADDRESS Type in the senders address Up to 60 alphanumeric and symbols characters can be used SMTP SERVER NAME Type in the SMTP server name to be connected to the projector Up to 60 alphanumeric characters can be used RECIPIENT S ADDRESS 1 to 3 Type in your recipient s address Up to 60 alphanumeric and symbols characters can be used APPLY sieisen Click this button to reflect the above settings EXE UTE noniin Click this button to send a test mail to check if your settings are correct STATUS nice nee A reply to a test mail will be displayed NOTE e f you execute a test you may not receive an Alert mail Should this happen check if the network settings are correct e f you entered an incorrect address in a test you may not receive an Alert mail Should this happen check if the Recipient s Ad dress is correct TIP The Alert Mail settings will not be affected even when RESET is done from the menu 49 4 Convenient Features Q Using the VGA Signal Cable to Operate the Projector Virtual Remote Overview The projector supports DDC CI Display Data Channel Command Interface that is a standard interface for bidirectional communication between display projector and computer The optional utility software Virtual Remote Too designed exclusively for our projector is required to use DDC CI Check with our website http www nec display com dl en index html NOTE Use the
61. ST BRIGHTNESS SHARPNESS COLOR HUE RESET CLOCK i PHASE HORIZONTAL ii VERTICAL IMAGE OVERSCAN i O 5 10 OPTIONS x NP600 NP500 NP400 NP300 NP600S AUTO 4 3 16 9 ASPECT RATIO 15 9 16 10 WIDE ZOOM NATIVE NP500W NPSOOWS AUTO 4 3 16 9 15 9 16 10 LETTERBOX NATIVE POSITION Not available on NP500W NP500WS VIDEO FILTER i OFF LESS MORE DIGITAL ZOOM NP600S NP500WS 100 80 100 AUTO KEYSTONE OFF OFF ON KEYSTONE 0 KEYSTONE SAVE OFF OFF ON OFF WHITEBOARD BLACKBOARD BLACKBOARD WALL COLOR OFF GRAY LIGHT YELLOW LIGHT GREEN LIGHT BLUE SKY BLUE LIGHT ROSE PINK GENERAL LAMP MODE NORMAL NORMAL ECO OFF CAPTION1 CAPTION2 CAPTIONS CAPTION4 SETUP pLOSED CAPTION OFF TEXT1 TEXT2 TEXT3 TEXT4 ENGLISH DEUTSCH FRAN AIS ITALIANO ESPANOL SVENSKA AXE DANSK PORTUGUES CESTINA MAGYAR POLSKI LANGUAGE ENGLISH NEDERLANDS SUOMI NORSK T RK E PX 21510 COLOR SELECT COLOR COLOR MONOCHROME DISPLAY TIME AUTO 45 SEC MANUAL AUTO 5 SEC AUTO 15 SEC AUTO 45 SEC MENU BACKGROUND BLUE BLUE BLACK LOGO FILTER MESSAGE 500 H OFF 100 H 200 H 500 H 1000 H ID DISPLAY ON OFF ON asterisk indicates that the default setting varies depending on the signal 53 5 Using On Screen Menu DESKTOP DESKTOP FRONT CEILING REAR
62. XGA WXGA SXGA SXGA UXGA 480i 480p 576i 576p 720p 1 080i Digital VGA SVGA XGA WXGA SXGA Video Bandwidth RGB 80 MHz Max Horizontal Resolution 540 TV lines NTSC NTSC4 43 PAL PAL M PAL N PAL60 300 TV lines SECAM Scan Rate Horizontal 15 kHz to 100 kHz RGB 24 kHz or over Vertical 50 Hz to 120 Hz Sync Compatibility Separate Sync Composite Sync Sync on G Built in Speaker 7W monaural Power Requirement NP600S 100 240V AC 50 60Hz NP600SG 200 240V AC 50 60Hz NP500WS 100 240V AC 50 60Hz NP500WSG 200 240V AC 50 60Hz Input Current Power Consumption NP600S 3 8 1 5A NP500WS 3 8 1 5A NP600SG 1 8A NP500WSG 1 8A 325W in Lamp NORMAL Mode 240W in Lamp ECO Mode 11W in STANDBY Mode 3W in POWER SAVING Mode 4 What is HDCP HDCP technology HDCP is an acronym for High bandwidth Digital Content Protection High bandwidth Digital Content Protection HDCP is a system for preventing illegal copying of video data sent over a Digital Visual Interface DVI If you are unable to view material via the DVI input this does not necessarily mean the projector is not functioning properly With the implementation of HDCP there may be cases in which certain content is protected with HDCP and might not be displayed due to the decision intention of the HDCP community Digital Content Protection LLC 5 An image with higher or lower resolution than the projector s nati
63. a NOTE In countries designated with an asterisk replacement product rental service are offered 7 Appendix Date L PH S TO NEC or NEC s Authorized Service Station FM Company amp Name with signature Dear Sir s would like to apply your TravelCare Service Program based on attached registration and qualification sheet and agree with your following conditions and also the Service fee will be charged to my credit card account if don t return the Loan units within the specified period also confirm following information is correct Regards Application Sheet for TravelCare Service Program Country product purchased Users Company Name Users Company Address Phone No Fax No User s Name User s Address Phone No Fax No Local Contact office Local Contact office Address Phone No Fax No User s Model Name Date of Purchase Serial No on cabinet Problem of units per User Required Service 1 Repair and Return 2 Loan unit Requested period of Loan unit Payment method 1 Credit Card 2 Travelers Cheque 3 Cash In Case of Credit Card Card No w Valid Date 98 Condition of your TravelCare Service Program Enduser is requested to understand following condition of TravelCare Service Program and complete the necessary information on the ap plication sheet 1 Service Options
64. age enables you to enjoy a much larger image when a smaller space is required Contact your NEC dealer if you need a mirror system If you re using a mirror system and your image is inverted use the MENU and SELECT buttons on your projector cabinet or your remote control to correct the orientation page 66 16 2 Installation and Connections Making Connections NOTE When using with a notebook PC be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on the power to the notebook PC In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up f the screen goes blank while using your remote control it may be the result of the computer s screen saver or power manage ment software Enabling the computer s external display Displaying an image on the notebook PC s screen does not necessarily mean it outputs a signal to the projector When using a PC compatible laptop a combination of function keys will enable disable the external display Usually the combination of the key along with one of the 12 function keys gets the external display to come on or off For example NEC laptops use Fn while Dell laptops use Fn F8 key combinations to toggle through external display selections Connecting Your PC or Macintosh Computer NOTE Signals supported by Plug amp Play DDC2
65. akes lightning damage storm or flood damage or other natural disasters or such external factors as dust cigarette smoke abnormal voltage etc 5 Problems or damage caused by use in hot or humid places in vehicles boats or ships etc 96 7 Appendix 6 Problems or damage caused by expendable supplies or devices connected to the product other than those designated by NEC 7 Problems caused by natural consumption wear or deterioration of parts under normal usage conditions 8 Problems or damage to lamps and other expendable supplies included parts or optional parts 9 Other conditions stipulated in the warranty included with the product also apply NOTE The product can be used overseas with voltages indicated in the rating label on the product by using a power cable suited for the standards and power source voltage of the country in which the product is being used List of TravelCare Outlets This list applies as of July 1 2008 For the most up to date information please refer to the websites of the service stations in the various countries on the List of TravelCare Outlets or to the NEC website at http www nec display com global index html In Europe NEC Europe Ltd European Technical Centre Address Unit G Stafford Park 12 Telford TF3 3BJ U K Telephone 44 1952 237000 Fax Line 44 1952 237006 Email Address AFRQ uk neceur com WEB Address http www neceur com Regions Covered EU Au
66. al temperature the LAMP MODE returns to NORMAL mode Thermometer symbol indicates the lamp mode is automatically set to ECO mode because the internal temperature is too high 41 4 Convenient Features Q Preventing the Unauthorized Use of the Projector SECURITY A keyword can be set for your projector using the Menu to avoid operation by an unauthorized user When a keyword is set turning on the projector will display the Keyword input screen Unless the correct keyword is entered the pro jector cannot project an image The SECURITY setting cannot be cancelled by using the RESET of the menu To enable the Security function 1 Press the MENU button The menu will be displayed 2 Press the SELECT gt button twice to select SETUP and press the SELECT button or the ENTER button to select GENERAL 3 Press the SELECT gt button to select INSTALLATION 4 Press the SELECT Y button three times to select SECURITY and press the ENTER button SOURCE ADJUST INFO RESET ORIENTATION DESKTOP FRONT CONTROL PANEL LOCK OFF OFF COMMUNICATION SPEED 19200bps CONTROL ID ENTER CJ COMPUTER The OFF ON menu will be displayed 5 Press the SELECT Y button to select ON and press the ENTER button SECURITY The SECURITY KEYWORD screen will be displayed 6 Type in a combination of the four SELECT AY 4 buttons and press the ENTER button NOTE A keyword must be 4 to 10 digits i
67. aneously project the computer s image This functionality eliminates the need to always use the POWER button on the remote control or the projector cabinet to power on the projector To use this function first connect a computer to the projector and the projector to an active AC input NOTE Disconnecting a computer signal from the computer will not power off the projector We recommend using this function in com bination of the AUTO POWER OFF function This function will not be available under the following conditions when a component signal is applied to the COMPUTER1 IN connector when a Sync on Green RGB signal or composite sync signal is applied when POWER SAVING is selected for STANDBY MODE e To enable the AUTO POWER ON after turning off the projector wait 3 minutes and input a computer signal If a computer signal is still present when the projector is turned off the AUTO POWER ON COMP1 will not work and the projector remains in standby mode Enabling Power Management AUTO POWER OFF When this option is selected you can enable the projector to automatically turn off at the selected time 5min 10min 20min 30min if there is no signal received by any input or if no operation is performed Selecting Default Source DEFAULT SOURCE SELECT You can set the projector to default to any one of its inputs each time the projector is turned on EAST aii S nsi te en Sets the projector to default t
68. are a service for international travelers This product is eligible for TravelCare NEC s unique international warranty Please note that TravelCare coverage differs in part from coverage under the warranty included with the product Services offered with TravelCare This warranty allows customers to receive service on their product at the NEC and NEC designated service stations in the countries listed herein when temporarily traveling internationally for business or pleasure For details on services offered by the different service stations please refer to the List of TravelCare Outlets below 1 Repair services The product will be repaired and delivered within 10 business days not including shipping time During the term of warranty the cost of maintenance parts labor costs for repairs and shipping costs within the service station s coverage area are covered by the warranty 2 Replacement product rental service If the customer desires he or she can rent a replacement product while the original product is being repaired Fee US 200 for 12 days This fee must be paid at the local service station in cash or credit card The US 200 rental fee is non refundable even if the customer rents itless than 12 days before returning The replacement product will be delivered within 3 business days If the customer did not return the replacement product within 12 days the customer will be charged the price of the unit If the customer re
69. bjects which are easily affected by heat in front of the projector lens Doing so could lead to the object melting from the heat that is emitted from the light output A No Place the projector in a horizontal position The tilt angle of the projector should not exceed 10 degrees nor should the projector be installed in any way other than the desktop and ceiling mount otherwise lamp life could decrease dramatically A Fire and Shock Precautions A Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build up of heat inside your projector Allow at least 4 inches 10cm of space between your projector and a wall Do not try to touch the ventilation outlet on the left front when seen from the front as it can become heated while the projector is turned on and immediately after the projector is turned off HOT Prevent foreign objects such as paper clips and bits of paper from falling into your projector Do not attempt to retrieve any objects that might fall into your projector Do not insert any metal objects such as a wire or screwdriver into your projector If something should fall into your projector disconnect it immediately and have the object removed by a qualified service personnel Do not place any objects on top of the projector Do not touch the power plug during a thunderstorm Doing so can cause electrical shock or fire The projector is designed to operate on a power supply o
70. cable can be used The DVI DIGITAL connector accepts VGA 640x480 SVGA 800x600 1152x864 XGA 1024x768 WXGA 1280x800 up to 60Hz and SXGA 1280x1024 Q up to 60Hz IBM PC or Compatibles Desktop type or Macintosh Desktop type UE Audio cable not supplied DVI cable not supplied oE Oo COMPUTER 2 DVI I IN 2 Installation and Connections Using Two Analog COMPUTER Inputs Simultaneously If you need to use two analog COMPUTER inputs simultaneously connect a VGA signal cable as shown below COMPUTER 2 DVI I IN COMPUTER 1 IN aol ju poor Compas pesto C M 27 type or Macintosh Desktop type VGA signal cable supplied DVI to VGA adapter supplied Suo da VGA signal cable not supplied ED ee aC Ste PC or Compatibles Notebook type or Macintosh Notebook type NOTE When the DVI to VGA adapter is not to be used for an extended period of time remove it from the projector Failure to do so may cause damage
71. ctors IP address gt index html e Alert Mail Setting http lt the projector s IP address gt lanconfig html TIP The default IP address is 192 168 0 10 The exclusive application can be downloaded from our website NOTE e If the PROJECTOR NETWORK SETTINGS screen does not appear in the web browser press the Ctrl F5 keys to refresh your web browser or clear the cache The display or button s response can be slowed down or operation may not be accepted depending the settings of your network Should this happen consult your network administrator The projector may not respond if its buttons are repeatedly pressed in rapid intervals Should this happen wait a moment and repeat If you still can t get any response turn off and back on the projector Preparation Before Use Connect the projector to a commercially available LAN cable before engaging in browser operations page 24 Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting method Although the type of proxy server will be a factor it is possible that items that have actually been set will not be displayed depending on the effectiveness of the cache and the contents set from the browser may not be reflected in operation It is recommended that a proxy server not be used unless it is unavoidable Handling of the Address for Operation via a Browser Regarding the actual address that i
72. d immediately after the projector is turned off Do not turn off the AC power for 60 seconds after the lamp is turned on and while the POWER indicator is blink ing green Doing so could cause premature lamp failure Remote Control Precautions Handle the remote control carefully If the remote control gets wet wipe it dry immediately Avoid excessive heat and humidity Do not heat take apart or throw batteries into fire If you will not be using the remote control for a long time remove the batteries Ensure that you have the batteries polarity aligned correctly Do not use new and old batteries together or use different types of batteries together Dispose of used batteries according to your local regulations Important Information Lamp Replacement e To replace the lamp follow all instructions provided on page 79 sure to replace the lamp when the message THE LAMP HAS REACHED THE END OF ITS USABLE LIFE PLEASE REPLACE THE LAMP appears If you continue to use the lamp after the lamp has reached the end of its usable life the lamp bulb may shatter and pieces of glass may be scattered in the lamp case Do not touch them as the pieces of glass may cause injury If this happens contact your dealer for lamp replacement A Lamp Characteristic The projector has a high pressure mercury lamp as a light source A lamp has a characteristic that its brightness gradually decreases with age Also repeatedly turnin
73. d triangle indicates the item is active lo Indicates a group of features in a dialog box Selecting on any tab brings its page to the front Radio button Use this round button to select an option in a dialog box DOUCE sicui UU Indicates the currently selected source Off Timer remaining time Indicates the remaining countdown time when the OFF TIMER is preset Slide Dar Indicates settings or the direction of adjustment Key Lock symbol Indicates the CONTROL PANEL LOCK is enabled Thermometer symbol Indicates the lamp mode is forcibly set to ECO mode because the internal temperature is too high High Altitude symbol Indicates the FAN MODE is set to HIGH ALTITUDE mode 52 List of Menu Items Some menu items are not available depending on the input source 5 Using On Screen Menu Menu ltem Default Options COMPUTER1 d COMPUTER2 DIGITAL SOURCE COMPUTER2 ANALOG VIDEO S VIDEO PRESET 1 6 GENERAL HIGH BRIGHT PRESENTATION VIDEO MOVIE REFERENCE GRAPHIC sRGB GAMMA CORRECTION DYNAMIC NATURAL BLACK DETAIL COLOR TEMPERATURE 5000 6500 7800 8500 9300 10500 WHITE DETAIL BALANCE SETTINGS CONTRAST R 0 CONTRAST G 0 PICTURE CONTRAST B 0 BRIGHTNESS R 0 BRIGHTNESS G 0 ADJUST See 0 CONTRA
74. e the supplied wireless remote control and the optional remote mouse receiver to operate your PC mouse from across the room The optional remote mouse receiver NPO1MR supports almost any PC using a USB connection About this user s manual The fastest way to get started is to take your time and do everything right the first time Take a few minutes now to review the user s manual This may save you time later on At the beginning of each section of the manual you ll find an overview If the section doesn t apply you can skip it 1 Introduction Comparative Table of Main Features The main features vary depending on the model as follows Standard Models Wide Panel Short Throw Wide Panel amp Short Model Model Throw Model NP600 NP500 NP400 NP300 NP500W NP600S NP500WS Native Aspect page 85 87 Standard Wide Standard Wide Native Resolution WXGA XGA WXGA dots x lines XGA 1024 x 768 page 85 87 1280 x 800 1024 x 768 1280 x 800 Screen Size uon i gt page 85 87 21 300 60 110 57 104 Distance 29 444 inches 0 7 11 3 m els 39 09 36 66 0 9 m 1 7 m page 85 87 0 7 10 6 m 0 9 m 1 7 m Light output in NORMAL mode page 85 87 Zoom page 32 Focus gt page 33 Lamp Replace ae TIME EVA 3000 H in NORMAL 4000 H in ECO page 73 3500 3000 2600 2200 3000 lumens 2600 lumens 2100 lumens lumens lumens lumens lumens
75. easing the drag mode is set and the drag operation can be performed simply by pressing the SELECT AY lt gt button To drop the item press the MOUSE L CLICK or R CLICK button To cancel it press the MOUSE R CLICK or L CLICK button TIP You can change the Pointer speed on the Mouse Properties dialog box on the Windows For more information see the user documentation or online help supplied with your computer 46 4 Convenient Features Q Network Setting by Using an HTTP Browser Overview Connecting the projector to a network allows the Alert Mail setting page 49 and the projector control from a computer via the network To perform the projector control from a web browser you must have an exclusive application installed on your com puter The IP address and subnet mask of the projector can be set on the Network Setting screen of the web browser by using an HTTP server function Please be sure to use Microsoft Internet Explorer 6 0 or a higher version for the web browser This device uses JavaScript and Cookies and the browser should be set to accept these functions The setting method will vary depending on the version of browser Please refer to the help files and the other information provided in your software Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected to the projector and enter the following URL e Network Setting http lt the proje
76. eatures 40 Turning off the Image and Sound ssesssseeeeeenmeenmn 40 Freezing a Pietre 40 Enlarging a Pi Ct Se D D 40 Changing Eamp MOGG stu orte ena E eser re nu cane eee b cada eae 41 Preventing the Unauthorized Use of the Projector SECURITY 42 Q Using the Optional Remote Mouse Receiver NPO1MR 45 Network Setting by Using an HTTP Browser 47 Using the VGA Signal Cable to Operate the Projector Virtual Remote 50 5 Using On Screen Menu 51 Using the Menus treten eee roter eruere e trennen 51 Menu Elemierits 2 52 List Menu Items ER e tea Poe auk ti end e Soin ERSTE Idee 53 Menu Descriptions amp Functions SOURCE 55 Menu Descriptions amp Functions ADJUST eerreesinrernneenrnereesere 56 Menu Descriptions amp Functions SETUP 63 Menu Descriptions amp Functions INFO seseeenennm nen 73 Menu Descriptions amp Functions RESET eeererererrnrerrnserrnerresere 75 6 Maintenance 1 sss 76 Cleaning or Replacing the Filters 76 Cleaning the Cabinet and the Lens 78 Replacing the er tenet rna t
77. ect keystone distortion gt e NOTE The Keystone correction can cause an image to be slightly blurred because the correction is made electronically The Keystone correction range can be made narrower depending on a signal or its aspect ratio selection Adjusting with buttons on the cabinet 1 Press the SELECT or Y button with no menus displayed The keystone bar will be displayed KEYSTONE ENTER EXIT LAMP O STATUS SOURCE AUTO ADJ 2 Use the SELECT A or Y to correct the keystone distortion The keystone bar will be closed after a period of time 3 Press the ENTER button The keystone bar will be closed NOTE When the menu is displayed the above operation is not available When the menu is displayed press the MENU button to close the menu and start the Keystone correction From the menu select SETUP GENERAL KEYSTONE The changes can be saved with KEYSTONE SAVE page 36 63 34 3 Projecting an Image Basic Operation Adjusting with the Remote Control 1 Press the MENU button The menu will be displayed 2 Press the SELECT gt button to select SETUP and press the ENTER button SOURCE ADJUST INFO RESET AUTO KEYSTONE OFF KEYSTONE i AU KEYSTONE SAVE OFF WALL COLOR OFF LAMP MODE NORMAL CLOSED CAPTION OFF LANGUAGE Ag ENGLISH ENTER EXIT CJ COMPUTER The GENERAL screen will be displayed 3 Press the SELECT Y button to select KEYSTO
78. ed caption is not available under the following conditions when messages or menus are displayed when an image is magnified frozen or muted Doing the following may cause portions of superimposed text or closed caption to be truncated If this occurs try to change correction amount or selection to place the superimposed text or closed caption within the screen Using the DIGITAL ZOOM or KEYSTONE function to correct the image excessively Selecting 16 10 or 16 9 from ASPECT RATIO Using the POSITION not available on NP500W NP500WS Selecting Menu Language LANGUAGE You can choose one of 21 languages for on screen instructions NOTE Your setting will not be affected even when RESET is done from the menu MENU SOURCE ADJUST INFO RESET e INSTALLATION OPTIONS 1 1 2 GENERAL COLOR SELECT COLOR DISPLAY TIME AUTO 45 SEC BACKGROUND BLUE FILTER MESSAGE 500 H ID DISPLAY ON 5 4GZAEEXIT MOVE e MOVE C2 COMPUTER1 Selecting Menu Color COLOR SELECT You can choose between two options for menu color COLOR and MONOCHROME Selecting Menu Display Time DISPLAY TIME This option allows you to select how long the projector waits after the last touch of a button to turn off the menu The preset choices are MANUAL AUTO 5 SEC AUTO 15 SEC and AUTO 45 SEC The AUTO 45 SEC is the fac tory preset Selecting a Color or Logo for Background
79. ed power cable to the projector First connect the supplied power cable s two pin plug to the AC IN of the projector and then connect the other plug of the supplied power cable in the wall outlet To wall outlet Make sure that the prongs are fully inserted into both the AC IN and the wall outlet A caution Do not try to touch the ventilation outlet on the left front when seen from the front as it can become heated while the projector is turned on and immediately after the projector is turned off 25 3 Projecting an Image Basic Operation This section describes how to turn on the projector and to project a picture onto the screen Q Turning on the Projector NOTE The projector has two power switches a main power switch and a POWER button POWER ON and OFF on the remote control e When plugging in or unplugging the supplied power cable make sure that the main power switch is pushed to the off O posi tion Failure to do so may cause damage to the projector 1 Remove the lens cap e Do not remove the lens cap by pulling on the string Doing so can cause mechanical damage to the part around the lens 2 To turn on the main power to the projector press the Main Power switch to the on position I The POWER indicator will light orange See the Power Indicator section page 82 26 3 Projecting an Image Basic Operation 3 Press the POWER but
80. ee tone ie etae rua teneo 79 7 ADDOR p MNT 82 Q Tro blesliootirig ss cotta Pte t aidant 82 Indicator Mossi S tierna tee tae eee rex 82 SPSCHIC A ONS 2221288258 eas M 85 Cabinet DIM NSIONS ER re ete eed ere eda ae tag va a ean ees 89 Pin Assignments of D Sub COMPUTER Input Connector 91 Mini D Sub 15 Pin Connector recentes Ea ri rere Pe 91 Compatible Input Signal List 92 Q PC Control Codes and Cable Connection 93 ddr dinde tree er tn ns 93 Cable Connection Dena eie Pu e EHE EE 93 PC Control Connector D SUB 9P iii 93 Troubleshooting Check List sise 94 TravelCare Guide teet iue EIE 96 vii 1 Introduction What s in the Box Make sure your box contains everything listed If any pieces are missing contact your dealer Please save the original box and packing materials if you ever need to ship your projector Projector Lens cap Lens cap 24F44681 24FU0691 Soft case 24BS7582 NP600 NP500 NP400 NP600S NP500WS NP600 NP500 NP400 The NP600S and the NP300 NP500W NP300 NP500W NP500WS do not come with a soft case VGA signal cable Remote control Batteries AAA x 2 Power cable 7N520052 7N900731 US 7N080229 EU 7N080
81. em me projector Button on the remote control cabinet VIDEO IN VIDEO VIDEO S VIDEO IN amp S VIDEO S VIDEO NOTE The AUDIO IN L and R jacks RCA are shared between the Video and S Video inputs NOTE Refer to your VCR owner s manual for more information about your equipment s video output requirements NOTE An image may not be displayed correctly when a Video or S Video source is played back in fast forward or fast rewind via Scan converter 23 2 Installation and Connections Connecting to a Network The projector comes standard with a LAN port RJ 45 which provides a LAN connection using a LAN cable Using LAN cable allows you to specify the Network Settings and the Alert Mail Settings for the projector over a LAN To use a LAN connection you are required to assign an IP address to the projector on the PROJECTOR NETWORK SETTINGS screen of the web browser on your computer For setting see page 47 48 49 Example of LAN connection Example of wired LAN connection Server Hub Al NOTE Use a Category 5 or higher LAN cable o 2 6 9 24 2 Installation and Connections Connecting the Supplied Power Cable Connect the suppli
82. ess the ENTER button SECURITY The KEYWORD CONFIRMATION screen will be displayed SECURITY KEYWORD K992 45L8 JNGJ 4XU9 1YAT EEA2 4 Type in your keyword and press the ENTER button When the correct keyword is entered the SECURITY function will be disabled NOTE If you forget your keyword contact your dealer Your dealer will provide you with your keyword in exchange for your request code Your request code is displayed in the Keyword Confirmation screen In this example K992 45L8 JNGJ 4XU9 1YAT EEA2 is request code 44 4 Convenient Features Q Using the Optional Remote Mouse Receiver NPO1MR The optional remote mouse receiver enables you to operate your computer s mouse functions from the remote control It is a great convenience for clicking through your computer generated presentations Connecting the remote mouse receiver to your computer If you wish to use the remote mouse function connect the mouse receiver and computer The mouse receiver can be connected directly to the computer s USB port type A NOTE Depending on the type of connection or OS installed on your computer you may have to restart your computer or change your computer settings Computer Remote mouse receiver When operating a computer via the remote mouse receiver 7m 22 feet Remote sensor on the remote mouse receiver When connecting using the USB terminal
83. f 100 240V AC 50 60 Hz NP600 NP500 NP400 NP300 NP500W NP600S NP500WS or 200 240V AC 50 60 Hz NP600G NP500G NP400G NP300G NP500WG NP600SG NP500WSG Ensure that your power supply fits this requirement before attempting to use your projector Do not look into the lens while the projector is on Serious damage to your eyes could result 4 vo gt NN Keep any items such as magnifying glass out of the light path of the projector The light being projected from the lens is extensive therefore any kind of abnormal objects that can redirect light coming out of the lens can cause unpredictable outcome such as fire or injury to the eyes Do not place any objects which are easily affected by heat in front of a projector exhaust vent Doing so could lead to the object melting or getting your hands burned from the heat that is emitted from the ex haust Important Information Handle the power cable carefully A damaged or frayed power cable can cause electric shock or fire Do not use any power cables than the supplied one Do not bend or tug the power cable excessively Do not place the power cable under the projector or any heavy object Do not cover the power cable with other soft materials such as rugs Do not heat the power cable Do not handle the power plug with wet hands Turn off the projector unplug the power cable and have the projector serviced by a qualified service personnel under the following conditions When
84. for ceiling ap plication Throw angle NOTE The values in the tables are design values and Screen bottom may vary NP600 NP500 NP400 NP300 Screen Size B C D Diagonal Width Height wide tele wide tele inch mm inch mm inch mm inch mm inch mm inch mm inch mm degree degree 21 533 17 427 13 320 4 110 30 753 2 50 8 3 25 635 20 508 15 381 5 131 29 746 36 903 2 60 10 0 8 3 30 762 24 610 18 457 6 157 36 903 43 1092 3 71 9 9 8 2 40 1016 32 813 24 610 8 210 48 1217 58 1469 4 95 9 8 8 1 60 1524 48 1219 36 914 12 314 73 1845 88 2223 6 143 9 7 8 0 72 1829 58 1463 43 1097 15 377 87 2221 105 2675 7 171 9 6 8 0 80 2032 64 1626 48 1219 17 419 97 2473 117 2977 8 191 9 6 8 0 84 2134 67 1707 50 1280 17 440 102 2598 123 3128 8 200 9 6 8 0 90 2286 72 1829 54 1372 19 471 110 2787 132 3354 8 214 9 6 8 0 100 2540 80 2032 60 1524 21 524 122 3101 147 3731 9 238 9 6 8 0 120 3048 96 2438 72 1829 25 629 147 3729 177 4485 11 286 9 6 8 0 150 3810 120 3048 90 2286 31 786 184 4671 E 221 5616 14 357 9 5 8 0 180 4572 144 3658 108 2743 37 943 221 5613 266 6747 17 429 9 5 8 0 200 5080 160 4064 120 3048 41 1048 246 6241 E 295 7501 19 476 9 5 8 0 210 5334 168 4267 126 3200 43 1100 2
85. g the lamp on and off will increase the possibility of its lower brightness A CAUTION When removing the lamp from a ceiling mounted projector make sure that no one is under the projector Glass fragments could fall if the lamp has been burned out About High Altitude mode e Set FAN MODE to HIGH ALTITUDE when using the projector at altitudes approximately 5500 feet 1600 meters or higher Using the projector at altitudes approximately 5500 feet 1600 meters or higher without setting to HIGH ALTITUDE can cause the projector to overheat and the protector could shut down If this happens wait a couple minutes and turn on the projector Using the projector at altitudes less than approximately 5500 feet 1600 meters and setting to HIGH ALTITUDE can cause the lamp to overcool causing the image to flicker Switch FAN MODE to AUTO e Using the projector at altitudes approximately 5500 feet 1600 meters or higher can shorten the life of optical com ponents such as the lamp About Copyright of original projected pictures Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as a coffee shop or hotel and employing compression or expansion of the screen image with the following func tions may raise concern about the infringement of copyrights which are protected by copyright law ASPECT RATIO KEYSTONE Magnifying feature and other similar featu
86. hows the percentage of remaining bulb life The value informs you of the amount of lamp usage When the remaining lamp time reaches the LAMP LIFE REMAINING bar indicator changes from 096 to 100 Hours and starts counting down If the remaining lamp time reaches 0 hours the projector will not turn on regardless of whether the LAMP MODE is set to NORMAL or ECO The message to the effect that the lamp or the filters should be replaced will be displayed for one minute when the projector is turned on and when the POWER button on the projector or the remote control is pressed To dismiss this message press any button on the projector or the remote control Lamp life H NORMAL ECO 3000 4000 NPO7LP Replacement lamp 73 SOURCE SOURCE ADJUST SETUP RESET SOURCE INDEX 108 HORIZONTAL FREQUENCY 48 kHz VERTICAL FREQUENCY 60 Hz SIGNAL TYPE RGB VIDEO TYPE SYNC TYPE SEPARATE SYNC SYNC POLARITY HC ViC SCAN TYPE NON INTERLACE EXIT CJ COMPUTER SOURCE INDEX HORIZONTAL FREQUENCY VERTICAL FREQUENCY SIGNAL TYPE VIDEO TYPE SYNC TYPE SYNC POLARITY SCAN TYPE WIRED LAN SOURCE ADJUST SETUP RESET PROJECTOR NAME NP600 Series MAC ADDRESS 00 00 00 00 00 00 EXIT CJ COMPUTER PROJECTOR NAME MAC ADDRESS VERSION SOURCE ADJUST SETUP RESET PRODUCT SERIAL NUMBER FIRMWARE DATA EXIT CJ COMPUTER PRODUCT SERIAL NUMBER FIRMWARE Ver
87. ill be displayed CONTROL ID ACTIVE GEET If the projector can be operated with the current remote control ID the ACTIVE will be displayed If the projector cannot be operated with the current remote control ID the INACTIVE will be displayed To operate the inactive projector assign the control ID used for the projector by using the following procedure Step 3 3 Press one of numeric keypad buttons while pressing and holding the ID SET button on the remote control NPO2RC Example To assign 3 press the 3 button on the remote control No ID means that all the projectors can be operated together with a single remote control To set No ID enter 000 or press the CLEAR button TIP The range of IDs is from 1 to 254 4 Release the ID SET button The updated CONTROL ID screen will be displayed NOTE The IDs can be cleared in a few days after the batteries are run down or removed 68 5 Using On Screen Menu OPTIONS 1 SOURCE ADJUST GENERAL MENU INSTALLATION e 1 2 AUTO ADJUST NORMAL FAN MODE AUTO SIGNAL SELECT WXGA MODE OFF DEINTERLACE ON BEEP ON DXENZXSSELECT ES3 EXIT MOVE MOVE COMPUTERI Setting Auto Adjust AUTO ADJUST This feature sets the Auto Adjust mode so that the computer signal can be automatically or manually adjusted for noise and stability You can automatically make adjustment in
88. ill go out NOTE Do not turn off the main power within 10 seconds of making adjustment or setting changes and closing the menu Doing so can cause loss of adjustments and settings CAUTION Parts of the projector will become heated during operation Use caution when picking up the projector immediately after it has been operating CAUTION The projector cannot be turned off for 60 seconds after the lamp is turned on and while the POWER indicator is blinking green Doing so could cause premature lamp failure 38 3 Projecting an Image Basic Operation Q After Use Preparation Make sure that the projector is turned off 1 Unplug the power cable 2 Disconnect any other cables 3 Retract adjustable tilt foot if extended 4 Cover the lens with the lens cap 5 Put the projector and accessories in the supplied soft case Place the projector in the soft case with the lens facing upward as shown below This is to prevent the lens from damage NOTE The NP600S and the NP500WS do not come with a soft case Insert the projector with the lens facing upward NOTE When placing the projector in the soft case retract the tilt foot and the rear feet Failure to do so may case damage to the projector CAUTION Use caution when putting the projector in the soft case immediately after the projector has been operating The projector cabinet is hot 39 4 Convenient Features
89. ill not turn on If this happens replace the lamp e f the lamp fails to light and if the STATUS indicator flashes on and off in a cycle of six times wait a full minute and then turn on the power NOTE Turning the Main Power Switch Off then Back On Allow a minimum of 1 second between turning off the main power switch and turning it back on again The same will be applied when a power strip equipped with a switch and a breaker is used Failing to do so could result in no power to the projector There will be no stand by LED Should this happen unplug the power cable and plug it in again Turn on the main power switch 28 3 Projecting an Image Basic Operation Selecting a Source Selecting the computer or video source NOTE Turn on the computer or video source equipment connected to the projector Selecting from Source List Press and quickly release the SOURCE button on the projector cabinet to display the Source list Each time the SOURCE button is pressed the input source will change as follows COMPUTER1 COMPUTER2 DIGITAL ANALOG VIDEO S VIDEO To display the selected source allow 1 second to elapse Detecting the Signal Automatically Press and hold the SOURCE button for a minimum of 2 seconds the projector will search for the next available input source Each time you press and hold the SOURCE button for a minimum of 2 seconds the input source will change as follows COMPUTER1 C
90. ill return your keystone correction settings to Zero ON i nat Saves current keystone correction settings Saving your change once affects all sources The changes are saved when the projector is turned off NOTE When AUTO KEYSTONE is set to ON KEYSTONE SAVE is not available Next time you turn on the power the AUTO KEYSTONE function will work and the data stored with KEYSTONE SAVE will be invalid 63 5 Using On Screen Menu Using the Wall Color Correction WALL COLOR eas WHITEBOARD BLACKBOARD gt BLACKBOARD GRAY LIGHT YELLOW LIGHT GREEN 2 LIGHT BLUE SKY BLUE 2 LIGHT ROSE 2 PINK This function allows for quick adaptive color correction in applications where the screen material is not white NOTE Selecting WHITEBOARD reduces lamp brightness Setting Lamp Mode to Normal or Eco LAMP MODE This feature enables you to select two brightness modes of the lamp NORMAL and ECO modes The lamp life can be extended by using the ECO mode Selecting ECO mode decreases fan noise when compared to NORMAL mode Lamp Mode Description Status of LAMP indicator This is the Default setting NORMAL 100 Brightness Of Select this mode to increase the lamp life approx 70 Brightness on NP600 ECO NP500W NP600S NP500WS and ap Steady Green light prox 80 Brightness on NP500 NP400 NP300 NOTE The LAMP LIFE REMAINING and LAMP HOURS USED can
91. in power is off Blinking light Green 0 5 sec On The projector is getting ready to turn on Wait for a moment 0 5 sec Off 2 5 sec On Off Timer is enabled 0 5 sec Off Orange 0 5 sec On The projector is cooling down Wait for a moment 0 5 sec Off Steady light Green The projector is turned on Orange The projector is in Standby Status Indicator Indicator Condition Projector Condition Note Normal or Standby POWER SAVING for _ m STANDBY MODE Blinking light Red 1 cycle 0 5 sec On Lamp cover error or lamp housing error Replace the lamp cover or lamp 2 5 sec Off housing correctly 2 cycle 0 5 sec On Temperature error The projector is overheated Move the 0 5 sec Off projector to a cooler location 3 cycle 0 5 sec On Power error Power unit is not working properly 0 5 sec Off Contact your dealer 4 cycle 0 5 sec On Fan error Fans will not work correctly 0 5 sec Off 6 cycle 0 5 sec On Lamp error Lamp fails to light Wait a full minute 0 5 sec Off and then turn on again Green Re firing the lamp The projector is cooling The projector is re firing down Wait for a moment Steady light Green Standby NORMAL for STANDBY MODE Orange Cabinet button is locked You have pressed cabinet button when Cabinet Button is locked Lamp Indicator Over Temperature Protection Indicator Condition Projector Condition Note Off
92. input signals on the following ports DVI I connector DVI I 29 Pin with HDCP compatible 15pin D Sub composite and S video Integrated RJ 45 connector for wired networking capability An RJ 45 connector is equipped as standard feature 7W built in speaker for an integrated audio solution Powerful 7 watt speaker provides volume need for large rooms Auto vertical keystone correction Auto Keystone feature allows the projector to detect its tilt and correct vertical distortion automatically LCD projector with high resolution and high brightness High resolution display up to UXGA compatible XGA NP600 NP500 NP400 NP300 NP600S WXGA NP500W NP500WS native resolution 1 Introduction e Six picture preset modes for user adjustable picture and color settings Each picture preset mode can be customized and memorized according to your preference e Preventing unauthorized use of the projector Enhanced smart security settings for keyword protection cabinet control panel lock security slot and security chain opening to help prevent unauthorized access adjustments and theft deterrence PC Control Port You can control the projector with a PC or control system using the PC Control port 3Win standby condition with energy saving technology Selecting POWER SAVING for STANDBY MODE from the menu can put the projector in power saving mode that consume less power than the normal standby condition e Optional remote mouse receiver You can us
93. is connected Consult the dealer or an experienced radio TV technician for help For UK only In UK a BS approved power cable with moulded plug has a Black five Amps fuse installed for use with this equipment If a power cable is not supplied with this equipment please contact your supplier Important Safeguards These safety instructions are to ensure the long life of your projector and to prevent fire and shock Please read them carefully and heed all warnings A Installation Do not place the projector in the following conditions on an unstable cart stand or table near water baths or damp rooms in direct sunlight near heaters or heat radiating appliances in a dusty smoky or steamy environment on a sheet of paper or cloth rugs or carpets f you wish to have the projector installed on the ceiling Do not attempt to install the projector yourself The projector must be installed by qualified technicians in order to ensure proper operation and reduce the risk of bodily injury In addition the ceiling must be strong enough to support the projector and the installation must be in accordance with any local building codes Please consult your dealer for more information Important Information WARNING Do not cover the lens with the lens cap or equivalent while the projector is on Doing so can lead to melting of the cap due to the heat emitted from the light output Do not place any o
94. is product will expose you to lead a chemical known to the State of California to cause birth defects or other reproductive harm WASH HANDS AFTER HANDLING RF Interference for USA only WARNING The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Display Solutions of America Inc in this manual Failure to comply with this government regu lation could void your right to operate this equipment This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver
95. isplays submenu for a confirmation Select YES and press the ENTER button NOTE Elapsed time of the lamp use will not be affected even when RESET is done from the menu NOTE The projector will turn off and go into standby mode when you continue to use the projector for another 100 hours after the lamp has reached the end of its life In this condition you cannot clear the lamp hour meter on the menu If this happens press the HELP button on the remote control for 10 seconds to reset the lamp clock back to zero Do this only after replacing the lamp Clearing the Filter Usage Hours CLEAR FILTER HOURS Resets the filter usage back to zero Selecting this option displays submenu for a confirmation Select YES and press the ENTER button NOTE Elapsed time of the filter use will not be affected even when RESET is done from the menu 75 6 Maintenance This section describes the simple maintenance procedures you should follow to clean the filters and replace the lamp Q Cleaning or Replacing the Filters The air filter sponge keeps dust and dirt from getting inside the projector and should be frequently cleaned If the filter is dirty or clogged your projector may overheat NOTE The message for filter cleaning will be displayed for one minute after the projector is turned on or off To cancel the message press any button on the projector cabinet or the remote control CAUTION e Turn off the projector
96. n length SECURITY KEYWORD The CONFIRM KEYWORD screen will be displayed 42 4 Convenient Features 7 Type in the same combination of SELECT AY lt gt buttons and press the ENTER button CONFIRM KEYWORD The confirmation screen will be displayed 8 Select YES and press the ENTER button SECURITY FUNCTION WILL BE ENABLED A ARE YOU SURE D The SECURITY function has been enabled To turn on the projector when SECURITY is enabled 1 Press and hold the POWER button for about 1 second The projector will be turned on and display a message to the effect that the projector is locked 2 Press the MENU button SECURIT Y KEYWORD K992 45L8 JNGJ 4XU9 1YAT EEA2 3 Type in the correct keyword and press the ENTER button The projector will display an image SECURITY KEYWORD K992 45L8 JNGJ 4XU9 1YAT EEA2 NOTE The security disable mode is maintained until the main power is turned off or unplugging the power cable 43 4 Convenient Features To disable the SECURITY function 1 Press the MENU button The menu will be displayed 2 Select SETUP gt INSTALLATION SECURITY and press the ENTER button SOURCE ADJUST INFO RESET ORIENTATION DESKTOP FRONT CONTROL PANEL LOCK OFF En COMMUNICATION SPEED 19200bps CONTROL ID ENTER EXIT CJ COMPUTER The OFF ON menu will be displayed 3 Select OFF and pr
97. nditions Upon acceptance of this NEC Projector Customer agrees to assume liability for this loan unit The current cost of use of this loan unit is US 200 for 12 calendar days If Customer does not return the unit within the 12 calendar days Cus tomer will be charged the next highest cost up to and including the full list price to Credit Cards which price will be informed by NEC Authorized Service Stations Please see the attached listing of contacts for each country to arrange for pickup of the loan unit If you return to their country of origin with the loan unit you will be charged additional freight to return the unit to the loaning country Thank you for your understanding of this program NEC NEC Display Solutions Ltd 2008 2009 7N951301
98. necting an External Monitor ssssssssssseseeeeeeneeeen nennen nennen 21 Connecting Your DVD Player with Component Output 22 Connecting Your VCR iii 23 Connecting tora Network coeno Eri dene eL ER EE coa n o 24 Connecting the Supplied Power Cable sse 25 3 Projecting an Image Basic Operation 26 Turning on the Projector is 26 Note on Startup screen Menu Language Select 28 Selecting a 29 Selecting the computer or video source 29 Adjusting the Picture Size and Position 30 Adjust the Tilt e 31 m EN 32 gc 33 Correcting Keystone Distortion nnne 34 Correcting Keystone Distortion sisinsdiran aS 34 Adjusting with buttons on the cabinet 34 Adjusting with the Remote Control ss 35 Adjusting with the Auto Keystone Function 36 Optimizing Computer Signal Automatically esee 37 Adjusting the Image Using Auto Adjust 37 vi Table of Contents Turning Up or Down Volumes cen een ie atin ied eens 37 Turning off the Projector iii 38 After 39 4 Convenient F
99. o the previous or last active input each time the projector is turned on AUTO Searches for an active source in order of COMPUTER COMPUTER 2 DIGITAL COMPUTER2 ANALOG VIDEO S VIDEO COMPUTER1 and displays the first found source COMPUTER Displays the computer signal from the COMPUTER 1 IN connector every time the projector is turned on COMPUTER2 DIGITAL Displays the DVI digital from the COMPUTER 2 IN connector every time the projector is turned on COMPUTER2 ANALOG Displays the computer signal from the COMPUTER 2 IN connector every time the projector is turned on VIDEO Displays the Video source from the VIDEO IN connector every time the projector is turned SVIDEO sisinio Displays the Video source from the S VIDEO IN connector every time the projector is turned on 72 5 Using On Screen Menu Q Menu Descriptions amp Functions INFO Displays the status of the current signal and lamp usage This item has four pages The information included is as follows TIP Pressing the HELP button on the remote control will show the INFO menu items USAGE TIME SOURCE ADJUST SETUP e SOURCE WIRED LAN VERSION CJ COMPUTER1 LAMP LIFE REMAINING SS LAMP HOURS USED 00000 H FILTER HOURS USED 00000 H GUR EXIT MOVE MOVE LAMP LIFE REMAINING LAMP HOURS USED H FILTER HOURS USED H The progress indicator s
100. ojector is in standby mode and before turning on the power to the notebook PC In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up NOTE You can check the horizontal frequency of the current signal in the projector s menu under Information If it reads OkHz this means there is no signal being output from the computer page 74 or go to next step Enabling the computer s external display Displaying an image on the notebook PC s screen does not necessarily mean it outputs a signal to the projector When using a PC compatible laptop a combination of function keys will enable disable the external display Usu ally the combination of the Fn key along with one of the 12 function keys gets the external display to come on or off For example NEC laptops use Fn while Dell laptops use Fn F8 key combinations to toggle through external display selections Non standard signal output from the computer If the output signal from a notebook PC is not an industry standard the projected image may not be displayed correctly Should this happen deactivate the notebook PC s LCD screen when the projector display is in use Each notebook PC has a different way of deactivate reactivate the local LCD screens as described in the previous step Refer to your computer s documentation for detailed information Image displayed is incorrect when using a Macintosh When u
101. ong detergents or solvents such as alcohol or thinner Vacuum the ventilation inlet of the cabinet Note on Cleaning the Lens NP600 NP500 NP400 NP300 NP500W Use a blower or lens paper to clean the lens and be careful not to scratch or mar the lens The NP600S and NP500WS have a plastic lens Use a commercially available plastic lens cleaner NOTE Do not scratch or mar the lens surface as a plastic lens is easily scratched Never use alcohol or glass lens cleaner as doing so will cause damage to the lens surface 78 6 Maintenance Replacing the Lamp When the lamp reaches the end of its life the LAMP indicator in the cabinet will blink red Even though the lamp may still be working replace the lamp to maintain the optimal projector performance After replacing the lamp be sure to clear the lamp hour meter page 75 CAUTION DO NOT TOUCH THE LAMP immediately after it has been used It will be extremely hot Turn the projector off wait 30 seconds turn off the main power switch and then disconnect the power cable Allow at least one hour for the lamp to cool before handling DO NOT REMOVE ANY SCREWS except one lamp cover screw and two lamp housing screws You could receive an electric shock Do not break the glass on the lamp housing Keep finger prints off the glass surface on the lamp housing Leaving finger prints on the glass surface might cause an unwanted shadow and poor picture quality
102. only This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regula tions Machine Noise Information Regulation 3 GPSGV The highest sound pressure level is less than 70 dB A in accordance with EN ISO 7779 CAUTION Avoid displaying stationary images for a prolonged period of time Doing so can result in these images being temporarily sustained on the surface of the LCD panel If this should happen continue to use your projector The static background from previous images will disappear Disposing of your used product EU wide legislation as implemented in each Member State requires that used electrical and electronic C products carrying the mark left must be disposed of separately from normal household waste This in cludes projectors and their electrical accessories or lamps When you dispose of such products please follow the guidance of your local authority and or ask the shop where you purchased the product After collecting the used products they are reused and recycled in a proper way This effort will help us reduce the wastes as well as the negative impact such as mercury contained in a lamp to the human health and the environment at the minimum level The mark on the electrical and electronic products only applies to the current European Union Member States Important Information WARNING TO CALIFORNIA RESIDENTS Handling the cables supplied with th
103. ou connect your computer for the first time Poor picture ee au Tat am SOURCE Normal picture aedes NOTE Some signals may take time to display or may not be displayed correctly e The Auto Adjust function does not work for component video and DVI digital signals e Ifthe Auto Adjust operation cannot optimize the computer signal try to adjust HORIZONTAL VERTICAL CLOCK and PHASE manually page 58 59 Q Turning Up or Down Volume Sound level from the speaker can be adjusted Increase volume Ju SOURCE AUTO ADJ 37 3 Projecting an Image Basic Operation Q Turning off the Projector To turn off the projector 1 First press the POWER button on the projector cabinet or the POWER OFF button on the remote con o trol The POWER OFF ARE YOU SURE message will appear O O LANP O STATUS POWER OFF se aoa ARE YOU SURE 2 Secondly press the ENTER button or press the Power On Fan running Standby POWER or the POWER OFF button again The power indicator will glow orange After the projec tor turns off the cooling fans keep operating for 30 seconds Cool down time Immediately after turning on the projector and display Sub Blinking Bis ing an image you cannot turn off the projector for 60 light orange light orange light seconds 3 Finally turn off the Main Power switch The power indi cator w
104. ource s resolution and frequency are supported by the projector Image is too dark Remains unchanged even though you adjust the brightness and or the contrast Image is distorted Image appears to be trapezoidal unchanged even though you carry out the KEYSTONE adjustment L Remote control does not work L No obstacles between the sensor of the projector and the remote control Projector is placed near a fluorescent light that can disturb the infrared remote controls Batteries are new and are not reversed in installation sometimes How often 94 Sh 7 Appendix other ut down during operation Power cable s plug is fully inserted into the wall outlet Lamp cover is installed correctly AUTO POWER OFF is turned off only models with the AUTO POWER OFF function OFF TIMER is turned off only models with the OFF TIMER Pa Lo function rts of the image are lost Still unchanged even though you press the AUTO ADJUST button Still unchanged even though you carry out RESET in the projector s menu age is shifted in the vertical or horizontal direction Horizontal and vertical positions are correctly adjusted on a computer signal Input source s resolution and frequency are supported by the projector Some
105. pixels are lost age is flickering Still unchanged even though you press the AUTO ADJUST button Still unchanged even though you carry out RESET in the projector s menu Image shows flickering or color drift on a computer signal Still unchanged even though you change FAN MODE from HIGH ALTITUDE to AUTO age appears blurry or out of focus Still unchanged even though you checked the signal s resolution on PC and changed it to projector s native resolution Still unchanged even though you adjusted the focus No sound Audio cable is correctly connected to the audio input of the projector Still unchanged even though you adjusted the volume level AUDIO OUT is connected to your audio equipment only models Bu with the AUDIO OUT connector ttons on the projector cabinet do not work only models with the CONTROL PANEL LOCK function CONTROL PANEL LOCK is not turned on or is disabled in the menu Still unchanged even though you press and hold the EXIT button for a minimum of 10 seconds In the space below please describe your problem in detail 7 Appendix Information on application and environment where your projector is used Projector Model number Serial No Date of purchase Lamp operating time hours
106. res Table of Contents Important Information i Introduction pnn nE 1 What sinthe BOX iine enit dec eei iei E E E A a E 1 Introduction to the Projector ss 2 Congratulations on Your Purchase of the Projector 2 Features YOUN V A eat tel 2 About this users Manual tus edit bn Ria et ann 3 Part Names of the Projector ir 5 PRON TOD P 5 piri EE 6 uuu IEEE 7 Terminal Panel Features riter 8 Part Names of the Remote Control 9 sica alacer 10 Remote Control Precautions nennen 10 Operating Range for Wireless Remote 10 2 Installation and Connections 11 Setting Up the Screen and the Projector 11 Selecting aA LOCATION PPS 11 Throw Distance and Screen Size 15 Making Connections inerte rnit rtt reri rint a tt Ehe 17 Enabling the computer s external display 17 Connecting Your PC or Macintosh Computer 17 When Viewing DVI Digital Signal sseseeeenn 19 Using Two Analog COMPUTER Inputs 20 Con
107. ro Lens Array 0 59 inch LCD with Micro Lens Array Aspect Ratio 4 3 Aspect Ratio 16 10 NP400 NP300 0 63 inch LCD Aspect Ratio 4 3 Resolution 1024 768 pixels 1280 x 800 pixels Lens Manual zoom and focus Zoom Ratio 1 1 2 Zoom Ratio 1 1 2 F1 7 2 0 f 19 8 23 7 mm F1 7 1 9 f 17 7 21 2 mm Lamp NP600 230W AC 168W in ECO Mode 230W AC 168W in ECO Mode Light Output NP600 3500 lumens NP500 3000 lumens NP400 2600 lumens NP300 2200 lumens approx 7096 in ECO Mode approx 80 in ECO Mode approx 80 in ECO Mode approx 80 in ECO Mode 3000 lumens approx 70 Mode Contrast Ratio s full white full black 500 1 Image Size Diagonal 21 300 inches 0 53 m 7 6 m Projection Distance 29 444 inches 0 7 11 3 m 28 419 inches 0 7 10 6 m Projection Angle Tele 7 9 8 3 Wide 9 5 10 0 Tele 7 6 7 9 Wide 9 1 9 5 1 Effective pixels are more than 99 99 2 This is the light output value lumens when the PRESET mode is set to HIGH BRIGHT If any other mode is selected as the PRESET mode the light output value may drop slightly 3 Compliance with ISO21 118 2005 Electrical Inputs 1 RGB Component D Sub 15 P 1 RGB Digital Analog DVI I 29 P HDCP supported 1 S Video DIN 4 P 1 Video RCA 1 L R RCA Audio 2 Stereo Mini Audio Outputs 1 RGB D Sub 15P 1 Stereo Mini Audio PC Con
108. s entered for the address or entered to the URL column when operation of the pro jector is via a browser the host name can be used as it is when the host name corresponding to the IP address of the projector has been registered to the domain name server by a network administrator or the host name corresponding to the IP address of the projector has been set in the HOSTS file of the computer being used Example 1 When the host name of the projector has been set to pj nec co jp access is gained to the network setting by specifying http pj nec co jp index html for the address or the entry column of the URL Example 2 When the IP address of the projector is 192 168 73 1 access is gained to the mail alert settings by specifying http 192 168 73 1 index html for the address or the entry column of the URL 47 4 Convenient Features Network Settings http lt the projector s IP address index html PROJECTOR NETWORK SETTINGS ITEM CURRENT VALUE NEW VALUE PHYSICAL ADDRESS MAC ADDRESS Xr LEGAS CANNOT BE MODIFIED IP NETWORK DHCP DISABLE OENABLE O DISABLE IPADDRESS 192 168 0 10 12 o 10 SUBNET MASK 2552552550 DEFAULT GATEWAY 192 168 0 1 12 e o ln DNS PRIMARY 0 0 0 0 0 o lo 0 DNS SECONDARY 0000 o Ip le lb FIRMWARE VERSION 1 00 MODEL NP600 Series CUPDATE Copyright C NEC Display Solutions Ltd 2008 All rights reserved
109. ser adjustable settings to customize each gamma or color Your settings can be stored in PRESET 1 to PRESET 6 Recommended for use in a brightly lit room Recommended for making a presentation using a PowerPoint file Recommended for typical TV program viewing Recommended for movies Recommended for graphics Standard color values DETAIL SETTINGS REFERENCE PRESENTATION GAMMA CORRECTION BLACK DETAIL C Tx ae 56 5 Using On Screen Menu GENERAL Storing Your Customized Settings REFERENCE This function allows you to store your customized settings in PRESET 1 to PRESET 6 First select a base preset mode from REFERENCE then set GAMMA CORRECTION and COLOR TEMPERA TURE HIGH BRIGHT Recommended for use in a brightly lit room PRESENTATION Recommended for making a presentation using a PowerPoint file VIDEO tns Recommended for typical TV program viewing MOVIE Recommended for movies GRAPHIC Recommended for graphics Standard color values Selecting Gamma Correction Mode GAMMA CORRECTION Each mode is recommended for DYNAMIC Creates a high contrast picture NATURAL Natural reproduction of the picture BLACK DETAIL Emphasizes detail in dark areas of the picture Adjusting Color Temperature COLOR TEMPERATURE This option allows you to select the color temperature of your choice NOTE When P
110. sing a Macintosh with the projector set the DIPswitch of the Mac adapter not supplied with the projector according to your resolution After setting restart your Macintosh for the changes to take affect For setting display modes other than those supported by your Macintosh and the projector changing the DIP switch on a Mac adapter may bounce an image slightly or may display nothing Should this happen set the DIP switch to the 13 fixed mode and then restart your Macintosh After that restore the DIP switches to a displayable mode and then restart the Macintosh again NOTE A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D Sub 15 pin connector Mirroring on a PowerBook When using the projector with a Macintosh PowerBook output may not be set to 1024 x 768 unless mirroring is off on your PowerBook Refer to owner s manual supplied with your Macintosh computer for mirroring Folders or icons are hidden on the Macintosh screen Folders or icons may not be seen on the screen Should this happen select View Arrange from the Apple menu and arrange icons 84 Specifications 7 Appendix This section provides technical information about projector s performance Model Number NP600 NP500 NP400 NP300 NP500W NP500 NP400 NP300 210W AC 168W ECO Mode Optical NP600 NP500 NP400 NP300 NP500W LCD Panel NP600 NP500 0 63 inch LCD with Mic
111. sion DATA Version CONTROL ID when CONTROL ID is set 74 5 Using On Screen Menu 5 Using On Screen Menu Q Menu Descriptions amp Functions RESET SOURCE ADJUST SETUP INFO CURRENT SIGNAL ALL DATA NETWORK SETTINGS CLEAR LAMP HOURS CLEAR FILTER HOURS 4UZX SELECT X X EXIT MOVE MOVE COMPUTERI Returning to Factory Default RESET The RESET feature allows you to change adjustments and settings to the factory preset for a all source s except the following CURRENT SIGNAL Resets the adjustments for the current signal to the factory preset levels The items that can be reset are PRESET CONTRAST BRIGHTNESS COLOR HUE SHARPNESS ASPECT RATIO HORIZONTAL VERTICAL CLOCK PHASE VIDEO FILTER and OVERSCAN ALL DATA Reset all the adjustments and settings for all the signals to the factory preset All items can be reset EXCEPT LANGUAGE BACKGROUND FILTER MESSAGE SECURITY COMMUNI CATION SPEED CONTROL ID SSTANDBY MODE FAN MODE LAMP LIFE REMAINING LAMP HOURS USED FILTER HOURS USED and NETWORK SETTINGS To reset the lamp usage time see Clearing Lamp Hour Meter CLEAR LAMP HOURS below Clearing Networking Settings NETWORK SETTINGS Returns DHCP IP ADDRESS SUBNET MASK and GATEWAY to the default settings Clearing Lamp Hour Meter CLEAR LAMP HOURS Resets the lamp clock back to zero Selecting this option d
112. stria Belgium Bulgaria Czech Republic Cyprus Denmark Estonia Finland France Germany Greece Hungary Ireland Italy Latvia Lithuania Luxembourg Malta The Netherlands Poland Portugal Romania Slovakia Slovenia Spain Sweden and the United Kingdom EEA Norway Iceland and Liechtenstein In North America NEC Display Solutions of America Inc Address 500 Park Boulevard Suite 1100 Itasca Illinois 60143 U S A Telephone 1 800 836 0655 Fax Line 1 800 356 2415 Email Address vsd tech support necsam com WEB Address http www necdisplay com Regions Covered U S A Canada In Oceania NEC Australia Pty Ltd Address New South Wales Sydney 184 Milperra Road Reversby NSW 2212 Telephone 131 632 Newcastle 120 Parry Street Newcastle West NSW 2302 Telephone 131 632 Victoria Melbourne Unit 1 6 Garden Road Clayton VIC 3168 Telephone 131 632 Queensland Brisbane Unit 4 305 Montague Road West End QLD 4101 Telephone 131 632 Southport Shop1 48 Ferry Road Southport QLD 4215 Telephone 131 632 South Australia Adelaide 84A Richmond Road Keswick SA 5035 Telephone 131 632 Western Australia Perth 45 Sarich Court Osborne Park WA 6017 Telephone 131 632 WEB Address http www nec com au Regions Covered Australia New Zealand In Asia and Middle East NEC Display Solutions Ltd Address 686 1 Nishioi Oi Machi Ashigarakami Gun Kanagawa 258 0017 Japan
113. supplied VGA signal cable to connect the COMPUTER 1 IN connector directly with the monitor output connector of the computer to use Virtual Remote Tool Using a switcher scan converter or other cables than the supplied VGA signal cable may cause failure in signal communication 50 5 Using On Screen Menu Q Using the Menus NOTE The on screen menu may not be displayed correctly while interlaced motion video image is projected 1 Press the MENU button on the remote control or the projector cabinet to display the menu SOURCE SETUP INFO RESET PRESET 2 PRESENTATION CGT DETAIL SETTINGS CONTRAST 4 em BRIGHTNESS ft SHARPNESS mt gt RESET D EXIT MOVE MOVE NOTE The commands such as ENTER EXIT AW lt b in the bottom show available buttons for your operation 2 Press the SELECT lt gt buttons on the remote control or the projector cabinet to display the submenu 3 Press the ENTER button on the remote control or the projector cabinet to highlight the top item or the first tab 4 Use the SELECT AY buttons on the remote control or the projector cabinet to select the item you want to adjust or set You can use the SELECT lt gt buttons on the remote control or the projector cabinet to select the tab you want 5 Press the ENTER button on the remote control or the projector cabinet to display the submenu window 6 Adjust
114. tances vary depending on the model NP600 NP500 NP400 NP300 The further your projector is from the screen or wall the larger the image The minimum size the image can be is approximately 21 0 53 m measured diagonally when the projector is roughly 30 inches 0 8 m from the wall or Screen The largest the image can be is 300 7 6 m when the projector is about 407 inches 10 3 m from the wall or screen Screen Size Unit cm inch 609 6 W x 457 2 H 240 W x 180 H 487 7 W x 365 8 H 192 W x 144 H 406 4 W x 304 8 H 160 W x 120 H 365 8 W x 274 3 H 144 W x 108 H 304 8 W x 228 6 H 120 W x 90 H 243 8 W x 182 9 H 96 W x 72 H 203 2 W x 152 4 H 80 W x 60 H 162 6 W x 121 9 H 64 W x 48 H 121 9 W x 91 4 H 48 W x 36 H TIP e The distances are indicated by intermediate values between tele and wide Use as a rule of thumb The Zoom lever adjusts the image size by up to 10 For more details on throw distance see page 15 11 2 Installation and Connections NP500W The further your projector is from the screen or wall the larger the image The minimum size the image can be is approximately 21 0 53 m measured diagonally when the projector is roughly 28 inches 0 7 m from the wall or screen The largest the image can be is 300 7 6 m when the projector is about 38
115. the lens Flicker appears on screen e Set FAN MODE to other than HIGH ALTITUDE mode when using the projector at altitudes approximately 5500 feet 1600 meters or lower Using the projector at altitudes less than approximately 5500 feet 1600 meters and setting to HIGH ALTITUDE can cause the lamp to overcool causing the image to flicker Switch FAN MODE to AUTO page 69 Image is scrolling vertically horizontally or both Remote control does not work e Use the COMPUTER1 the COMPUTER2 the VIDEO or the S VIDEO button on the remote control to select your source Computer Video or S Video page 29 e Adjust the computer image manually with the Horizontal Vertical in the IMAGE OPTIONS page 59 Install new batteries page 10 Make sure there are no obstacles between you and the projector e Stand within 22 feet 7 m of the projector page 10 Indicator is lit or blinking e See the POWER STATUS LAMP Indicator page 82 Cross color in RGB mode e Press the AUTO ADJ button on the projector cabinet or the remote control page 37 e Adjust the computer image manually with CLOCK PHASE in IMAGE OPTIONS in the menu page 58 For more information contact your dealer 83 7 Appendix If there is no picture or the picture is not displayed correctly Power on process for the projector and the PC Be sure to connect the projector and notebook PC while the pr
116. the projector at altitudes less than approximately 5500 feet 1600 meters and setting to HIGH ALTITUDE can cause the lamp to overcool causing the image to flicker Switch FAN MODE to AUTO Using the projector at altitudes approximately 5500 feet 1600 meters or higher can shorten the life of optical components such as the lamp Your setting will not be affected even when RESET is done from the menu 69 5 Using On Screen Menu Selecting Signal Format SIGNAL SELECT COMPUTER1 COMPUTER2 ANALOG Allows you to choose COMPUTER1 or COMPUTER2 ANALOG for an RGB source such as a computer or COMPONENT for a component video source such as a DVD player Normally select RGB COMPONENT and the projector automatically detects a component signal However there may be some component signals that the projector is unable to detect If this is the case select COMPONENT VIDEO amp S VIDEO System Select This feature enables you to select composite video standards automatically or manually Normally select AUTO and the projector will automatically detect the video standard In the case where the projector has difficulty detecting the video standard select the appropriate video standard from the menu This must be done for VIDEO and S VIDEO respectively Enabling or Disabling WXGA Mode WXGA MODE Selecting ON will give priority to a WXGA 1280 x 768 signal in recognizing an input signal When WXGA MODE is set to
117. to the connector of the projector 20 2 Installation and Connections Connecting an External Monitor VGA signal cable not supplied VGA signal cable sup plied VWF El a AUDIO m IN o A FL You can connect a separate external monitor to your projector to simultaneously view on a monitor the computer analog image you re projecting NOTE Daisy chain connection is not possible When audio equipment is connected the projector speaker is disabled 21 2 Installation and Connections Connecting Your DVD Player with Component Output COMPUTER 1 IN AUDIO IN 15 pin to RCA fe male x 3 cable adapter ADP CV1E t Audio Equipment l muumunuumuumumuummumummm AUD
118. ton on the projector cabinet do or the POWER ON button on the remote control for 1 sc AUTO Ans second The POWER indicator will turn to green and the projector will become ready to use TIP When the STATUS indicator lights orange it means that the CONTROL PANEL LOCK is turned on page 67 When the message Projector is locked Enter your password is displayed it means that the SECURITY is turned on gt page 42 Standby Blinking Power On After you turn on your projector ensure that the computer or video source is turned on and that your lens cap is se removed O SOURCE AUTO ADJ NOTE When no signal is available the NEC logo blue default or a orangecign black screen will be displayed When the projector displays the NEC logo a blue or black screen the projector will automatically switch to the ECO mode The projector will return to the NORMAL mode once a signal is connected page 82 27 3 Projecting an Image Basic Operation Note on Startup screen Menu Language Select screen When you first turn on the projector you will get the Startup menu This menu gives you the opportunity to select one of the 21 menu languages To select a menu language follow these steps 1 Use the SELECT A V 4 button to select one of the 21 languages from the menu PLEASE SELECT A MENU LANGUAGE ce RICE NORSK DEUTSCH
119. trol 1 PC Control Port D Sub 9P Wired LAN Port RJ 45 External Control RS232 IR Wired LAN Color Reproduction 16 7 million colors simultaneously Full color Compatible Signals Analog VGA SVGA XGA WXGA WXGA SXGA SXGA UXGA 480i 480p 576i 576p 720p 1 080i Digital VGA SVGA XGA WXGA SXGA Video Bandwidth RGB 80 MHz Max Horizontal Resolution 540 TV lines NTSC NTSC4 43 PAL PAL M PAL N PAL60 300 TV lines SECAM Scan Rate Horizontal 15 kHz to 100 kHz RGB 24 kHz or over Vertical 50 Hz to 120 Hz Sync Compatibility Separate Sync Composite Sync Sync on G Built in Speaker 7W monaural 4 What is HDCP HDCP technology HDCP is an acronym for High bandwidth Digital Content Protection High bandwidth Digital Content Protection HDCP is a system for preventing illegal copying of video data sent over a Digital Visual Interface DVI If you are unable to view material via the DVI input this does not necessarily mean the projector is not functioning properly With the implementation of HDCP there may be cases in which certain content is protected with HDCP and might not be displayed due to the decision intention of the HDCP community Digital Content Protection LLC 85 7 Appendix 5 An image with higher or lower resolution than the projector s native resolution NP600 NP500 NP400 NP300 1024 x 768 NP500W 1280 x 800 will be displayed with Ad
120. ts or failures result from any cause other than fair wear and tear or NEC neglect or fault including the following without limitation 1 Accidents transportation neglect misuse abuse water dust smoke or default of or by the Customer its employees or agents or any third party 2 Failure or fluctuation of electrical power electrical circuitry air con ditioning humidity control or other environmental conditions such as use it in smoking area 3 Any fault in the attachments or associated products or components whether or not supplied by NEC or its agents which do not form part of the Product covered by this warranty 4 Any act of God fire flood war act of violence or any similar occur rence 5 Any attempt by any person other than any person authorized by NEC to adjust modify repair install or service the product 6 Any Cross border charges such as duty insurance tax etc 3 Charges for Warranty Exclusions and Out of Warranty Case In case faulty unit is under warranty exclusions case or under Out of Warranty period NEC Authorized Service Station will Inform estimation of actual service cost to the Enduser with reason 4 Dead on Arrival DOA Enduser must take this issue up with their original supplier in the country of purchase NEC Authorized Service Station will repair the DOA unit as a Warranty repair but will not exchange DOA unit with new units 99 7 Appendix 5 Loan Service Charges and Co
121. tting ID to the Projector CONTROL ID Available only when the optional remote control NPO2RC is used You can operate multiple projectors separately and independently with the single remote control that has the CONTROL ID function If you assign the same ID to all the projectors you can conveniently operate all the projectors together using the single remote control To do so you have to assign an ID number to each projector CONTROL ID NUMBER Select a number from 1 to 254 you wish to assign to your projector CONTROL ID Select OFF to turn off the CONTROL ID setting and select ON to turn on the CONTROL ID set ting ID DISPLAY This option turns on or off the ID number which is displayed when the ID SET button on the remote control is pressed NOTE Selecting ON for CONTROL ID will make the remote control supplied with the projector inoperable The buttons on the projector cabinet can be used Neither can you operate the projector by using the optional remote control NPO1RC that does not has the CONTROL ID function e Your setting will not be affected even when RESET is done from the menu Pressing and holding the ENTER button on the projector cabinet for 10 seconds will display the menu for canceling the Control ID Assigning or Changing the Control ID 1 Turn on the projector 2 Press the ID SET button on the remote control NPO2RC The CONTROL ID screen w
122. turned the replacement product in a faulty or dam aged condition the repair cost will be charged to the customer Note that this service is not offered in all countries and regions Please refer to the List of TravelCare Outlets In addition this replacement product rental service is not offered after the product s warranty has expired Term of warranty 1 a Upon presentation of the warranty or receipt received upon purchase Valid for the term indicated on the warranty or the normal term of warranty for the country of purchase b When only the product is brought in Valid for a period of within 14 months of the date of manufacture indicated by the serial number attached to the product 2 When a product whose term of warranty is expired is brought in Repairs will be offered for a fee In this case the customer is not eligible for the replacement product rental service 3 In the following cases repairs may be charged even if the product s warranty is still in effect 1 If the term of warranty model name serial number and name of the store of purchase are not indicated on the warranty or have been altered 2 Problems or damage caused by dropping or shocks during ship ment or movement by the customer or by improper handling by the customers 3 Problems or damage caused by improper usage or unwarrantable alterations or repairs by the customer 4 Problems or damage caused by fire salt damage gas damage earthqu
123. two ways NORMAL and FINE OFF esent The computer signal will not be automatically adjusted You can manually optimize the computer signal NORMAL Default setting The computer signal will be automatically adjusted Normally select this option FINE sinn Select this option if fine adjustment is needed It takes more time to switch to the source than when NORMAL is selected Selecting Fan Mode FAN MODE This option allows you to select three modes for fan speed Auto mode High speed mode and High Altitude mode AUTO The built in fans automatically run at a variable speed according to the internal temperature HIGH iesus The built in fans run at high speed HIGH ALTITUDE The built in fans run at a high speed Select this option when using the projector at altitudes approximately 5500 feet 1600 meters or higher When you wish to cool down the temperature inside the projector quickly select HIGH NOTE e t is recommended that you select High speed mode if you use the projector non stop for consecutive days Set FAN MODE to HIGH ALTITUDE when using the projector at altitudes approximately 5500 feet 1600 meters or higher Using the projector at altitudes approximately 5500 feet 1600 meters or higher without setting to HIGH ALTITUDE can cause the projector to overheat and the protector could shut down If this happens wait a couple minutes and turn on the projector Using
124. vanced AccuBlend Power Requirement NP600 NP500 NP400 NP300 100 240V AC NP500W 100 240V AC 50 60Hz 50 60Hz NP500WG 200 240V AC 50 60Hz NP600G NP500G NP400G NP300G 200 240V AC 50 60Hz Input Current NP600 3 8 1 5A NP500W 3 8 1 5A NP500 NP400 NP300 3 5 1 4A NP500WG 1 8A NP600G 1 8A NP500G NP400G NP300G 1 6A Power Consumption NP600 325W in Lamp NORMAL Mode 325W in Lamp NORMAL Mode 240W in Lamp NP500 NP400 NP300 295W in Lamp NORMAL ECO Mode 11W in STANDBY Mode 3W in POWER Mode SAVING Mode NP600 NP500 NP400 NP300 240W in Lamp ECO Mode 11W in STANDBY Mode 3W in POWER SAV ING Mode Mechanical Installation Orientation Desktop Front Desktop Rear Ceiling Front Ceiling Rear Dimensions 12 1 W x 3 7 H x 10 3 D 308 mm W x 93 5 mm H x 262 mm D not including protrusions Weight 6 57 lbs 2 98 kg Environmental Considerations Operational Temperatures 41 to 104 F 5 to 40 C ECO mode selected automatically at 95 F to 104 F 35 C to 40 20 to 80 humidity non condensing Storage Temperatures 14 to 122 F 10 to 50 20 to 80 humidity non condensing Regulations UL C UL Approved UL 60950 1 CSA 60950 1 Meets DOC Canada Class B requirements Meets FCC Class B requirements Meets AS NZS CISPR 22 Class B Meets EMC Directive EN55022 EN55024 EN61000 3 2 EN61000 3 3 Meets Low Voltage Directive EN60950 1 T V GS Approved 86
125. ve resolution NP600S 1024 x 768 NP500WS 1280 x 800 will be displayed with Advanced AccuBlend 87 Mechanical 7 Appendix Installation Orientation Desktop Front Desktop Rear Ceiling Front Ceiling Rear Environmental Considerations Dimensions 12 1 W x 5 4 H x 11 9 D 308 mm W x 136 mm H x 301 mm D not including protrusions Weight 7 28 lbs 3 3kg Operational Temperatures 41 to 104 F 5 to 40 C ECO mode selected automatically at 95 F to 104 F 35 C to 40 2096 to 80 humidity non condensing Storage Temperatures 14 to 122 F 10 to 50 2096 to 80 humidity non condensing Regulations UL C UL Approved UL 60950 1 CSA 60950 1 Meets DOC Canada Class B requirements Meets FCC Class B requirements Meets AS NZS CISPR 22 Class B Meets EMC Directive EN55022 EN55024 EN61000 3 2 EN61000 3 3 Meets Low Voltage Directive EN60950 1 T V GS Approved CE For additional information visit US http www necdisplay com Europe http www nec display solutions com Global http www nec display com global index html For information on our optional accessories visit our website or see our brochure The specifications are subject to change without notice 88 Q Cabinet Dimensions NP600 NP500 NP400 NP300 NP500W 108 5 4 3
126. while the projector is in standby mode and before turning on the power to the notebook PC In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered up Ifthe screen goes blank while using your remote control it may be the result of the computer s screen saver or power management software See also the next page Picture suddenly becomes dark Check if the projector is in the Forced ECO mode because of too high ambient temperature If this is the case lower the internal temperature of the projector by selecting HIGH for FAN MODE page 69 Color tone or hue is unusual e Check if an appropriate color is selected in WALL COLOR If so select an appropriate option page 64 e Adjust HUE in PICTURE page 57 Image isn t square to the screen e Reposition the projector to improve its angle to the screen page 30 e Use the Keystone correction function to correct the trapezoid distortion page 34 Picture is blurred Adjust the focus page 33 e Reposition the projector to improve its angle to the screen page 30 Ensure that the distance between the projector and screen is within the adjustment range of the lens page 15 Condensation may form on the lens if the projector is cold brought into a warm place and is then turned on Should this happen let the projector stand until there is no condensation on

NP600/NP500/NP400/ NP300/NP500W NP600S

Contents

Download Pdf Manuals

Related Search

Related Contents