Setting Up the Scanner
Contents
1. 4 Turn on the EAS system 5 LED signal and beep sound should be made when attempting to demagnetize Dual Laser Omnidirectional Vertical Scanner 12 UsER s MANUAL Maintaining the Scanner The scanner is designed for long term trouble free operation and rarely needs any maintenance Only an occasional cleaning of the scanner window is necessary in order to remove dirt and fingerprints Cleaning the Scan Window Wipe the scan window with a soft lint free cloth and a non abrasive cleaner to avoid scratching The scan window may be cleaned while the scanner is running Replacing the Interface Cable The standard interface cable is attached to the scanner with an 8 pin modular connector When properly seated the connector is secured in the scanner handle by a flexible retention tab The cable is designed to be field replaceable Replacement cables can be obtained from your authorized distributor To replace the cable follow these steps 1 Make sure that the power of your computer system is switched off and if a power adapter is used disconnect it from the scanner cable 2 Disconnectthe old scanner cable from the computer system 3 Remove the screws that hold the mounting plate on the scanner and disengage the mounting plate 4 Pressdown the small tab on the connector where the old cable is attached to the scanner and pull The connector should come out Insert the connecting cable in the slot in the mounting plate 6 I2. 152mm 1 2kg Standard 2m straight Dual Laser Omnidirectional Vertical Scanner 14 USER S MANUAL POWER Input Voltage 5VDC 10 Power 1 5 watts Operating Current 300mA 5 V Laser Class CDRH Class Il a IEC 60825 1 Class EMC CE amp FCC DOC compliance ENVIRONMENT Operating Temperature 0 C 40 C Storage Temperature 20 C 60 C Humidity 5 95 RH non condensing Light Level max 4000 LUX fluorescent Shock Designed to withstand 1m drops Specifications subject to change without notice 15 Dual Laser Omnidirectional Vertical Scanner USER S MANUAL Dimension Units mm inches Dimension Dual Laser Omnidirectional Vertical Scanner 16 4 73 109 top view kan TH in A E 428 108 El CPET g m 8 5 Q if AJ Bh 0 4 59 B in mm Scan Field UsER s MANUAL 17 Dual Laser Omnidirectional Vertical Scanner USER S MANUAL Pin Assignments Connecting Ports HOST Port kaweariban Keyboard Data N C AUX Port N NC 5 V out 150mA max RIS Out Ground TXD Out RXD In Dual Laser Omnidirectional Vertical Scanner 18 USER S MANUAL Troubleshooting Problem Diagnostic Tips The scanner is on but cannot The scanner window is dirty Clean the scan ner read barcodes The LED stays window as described in the Maintenance section The presented barcode type is not enabled Use the Programming Guide to tell the scan ner to acce
3. barcode The scanner beeps twice once long and once short and the LED returns to blue The scanner has been programmed 5 Test again with known good barcodes If results are good you are done setting Dual Laser Omnidirectional Vertical Scanner up Otherwise return to step 1 and try again UsER s MANUAL Operation The scanner can read barcodes in either sweep or presentation mode to accommodate different requirements Sweep mode means moving items through the scan volume Left to right right to left top to bottom bottom to top etc are all okay This scanner is truly omnidirectional Sweep scanning is usually used for high throughput and reduced product handling Presentation scanning is used where counter top space is at a premium The product is moved toward the scan window presented until the barcode is read then the product is removed LED Indications A dual color red blue LED indicates operating status as follows LED status Indication No power supplied to the scanner Steady blue light The scanner is on and ready to scan One red flash A barcode has been successfully decoded Steady red light A barcode has been successfully decoded but the object is not removed from the scan window The scanner is in programming mode Flashing blue light The scanner is in sleep mode Steady red blue light This indicates the scanner has a motor or laser failure For motor failure a periodic beep is sounded Ret
4. This advanced scanner is a proud to be among the world s first dual laser presentation scanners and it incorporates numerous record breaking features Its pioneering application of dual laser diodes drastically enhances scanning power by doubling the scan lines broadening scan angle and intensifying the scan pattern across the scan field With this state of the art technology it is able to deliver a comprehensive 32 line scan pattern cycling at 2400 scans per second The scanner is additionally equipped with Z SCAN technology an innovative ASIC hardware decode protocol that provides real time decoding that effectively shortens customer transaction time The broad omnidirectional scan field effectively facilitates hands free scanning of barcodes on products of many different shapes Also the scanner is programmed with multiple beeper tones and barcode data edition functions to accommodate a variety of applications Unpacking Dual Laser Omnidirectional Vertical Scanner with attached mounting plate 5V power adapter model depends on electrical requirements of your geographic location User s Manual Programming Guide CD b Connection cable This cable is usually but not always supplied Model depends on customer needs Screws Please check for any damaged or missing items contact your dealer if there is a problem 1 Dual Laser Omnidirectional Vertical Scanner USER S MANUAL Finding Your Way Around LED indica
5. and is ready to go In other cases the scan ner must be informed about what kind of system it is connected to This can be done in a few moments using the included booklet titled Programming Guide The Programming Guide may be used to set a number of parameters on the scanner communication interface type RS 232 Keyboard USB beep tone sleep mode timings same code delay time enable disable decoding of numerous code types and more advanced things like set headers and trailers Individual parameters may be set at any time without affecting the other parameters Scan Test With the scanner running LED blue and the host system on try to scan several known good barcodes 2 Checktheresults on the POS screen If the scanner is reading okay no fur ther setup may be necessary 3 Ifthe POS screen does not show the expected scans go to Set Up below Set Up 1 With the scanner running LED blue and the host system on present the Enter Exit Programming Mode barcode found on the inside cover of the Programming Guide to the scanner The scanner gives two beeps low and high and the LED turns red The scanner is in programming mode 2 Decide which parameters are required and find their barcodes in the Programming Guide 3 Coverunwanted codes with your hand and present the desired codes one by one to the scanner The scanner beeps once as it accepts each code 4 When done again present the Enter Exit Programming Mode
6. automatically turns off after some more time the motor turns off and the scanner enters sleep mode indicated by the blue status LED blinking once a second To wake up the unit simply present an object close to the scanner window or press the push button Note The scanner includes a motion sensor that detects activity in front of the scan window The detecting distance is up to about 50mm 2 inches from the scan window depending on ambient light Controlling the Scanner from a POS System The scanner can be controlled from the POS system via the RS 232C interface Control can be accomplished by transmitting the following single byte com mands to the scanner The default settings for the commands are as follows ASCII Function Byte is Also Code Called enable resumes from disable Shift Out or Ctrl N wake up resumes sleep DC4 Ctrl T Note When the scanner is disabled the scanner motor will continue running until the scanner goes into sleep mode 11 Dual Laser Omnidirectional Vertical Scanner USER S MANUAL Connecting to EAS System Optional To install an EAS the deactivator must be equipped with EAS connector Make sure that the power of the EAS system is off 1 D emagnetizing coil can be installed around the scan window Please see your EAS User s Manual or contact the manufacturer for assistance 2 Connect the deactivator using the EAS connector on the back of the scanner gt wa
7. connector into the 10 pin aux jack until it clicks and route the cable through the space above the scanner interface cable 4 Move the scanner into position on the mounting plate engaging the tab on the underside Be careful not to pinch any cables 5 Replace the mounting plate screws Back Mounting If desired the scanner may be mounted to your own custom bracket using the threaded mounting holes on the back See page 2 Figure The mounting holes are threaded to accommodate M4 x 0 7 machine screws to a depth of 5 0 mm Make sure your bracket design allows for the exit of the interface cable The supplied mounting plate protects the interface cable connection but requires that the cable exits from the back of the unit Connecting to the Host The power link interface cable comes with different host end connectors depending on the host Follow the steps below to connect the interface cable to the host 1 Make sure that the power of the host system is off 2 Connect the host end of the interface cable to the appropriate connector on the host system 3 For those cases where external power is used plug the external AC power adapter into the jack on the interface cable See page 2 Figure 4 Turn on the host system 7 Dual Laser Omnidirectional Vertical Scanner UsER s MANUAL Setting Up the Scanner In some cases no setup is required The scanner is either pre programmed to suit the situation or it auto detects
8. of the mounting process Dual Laser Omnidirectional Vertical Scanner 4 USER S MANUAL Mounting Plate Installation 1 Position the mounting plate in the desired location and secure it in place If desired use the full size boring template in page 21 Figure 2 Insert the connecting cable in the slot in the mounting plate 3 Insert the 8 pin modular plug of the power link cable into the host connector in the back of the scanner until a firm click is heard 5 Dual Laser Omnidirectional Vertical Scanner USER S MANUAL 4 Move the scanner into position on the mounting plate engaging the tab on the underside Be careful not to pinch the cable 4c Install Scanner on Mounting Plate 5 Replace the mounting plate screws Auxiliary Handheld Scanner Connection optional The scanner supports the operation of an auxiliary handheld scanner which may be connected via a 10 pin RS 232 modular plug to the connector marked aux in the back of the scanner 1 Insert the connecting cable in the slot in the mounting plate but reverse the cable relief molding of the scanner interface cable in the mounting plate to allow space for the auxiliary handheld scanner cable Dual Laser Omnidirectional Vertical Scanner USER S MANUAL 2 Insert the 8 pin modular plug of the power link cable into the host connector in the back of the scanner until a firm click is heard 3 Insert the auxiliary cable
9. User s Manual Dual Laser Omnidirectional Vertical Scanner Important Notice No warranty of any kind is made in regard to this material including but not limited to implied warranties of merchantability or fitness for a particular purpose We are not liable for any errors contained herein or incidental or consequential damages in connection with furnishing performance or use of this material No part of this document may be reproduced transmitted stored in a retrieval system transcribed or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without express written consent and authorization We reserve the right to make changes in product design without reservation and without notification The material in this guide is for information only and is subject to change without notice Forthe latest revision please contact your distributor All trademarks mentioned herein registered or otherwise are the properties of their various respective owners Copyright 2012 All rights reserved Printing Guidance This manual is in A5 size Please double check your printer setting before printing it out Revision History Changes to the original manual are listed below Version Date Description of Version Oct 2012 Dual Laser Omnidirectional Vertical Scanner Laser Safety The Miniature Dual Laser Omnidirectional Han
10. ds free Scanner complies with safety standard IEC 60825 for a Class laser product It also complies with CDRH as applicable to a Class lla laser product Avoid long term staring into direct laser light Radiant Energy The Miniature Dual Laser Omnidirectional Hands free Scanner uses two low power visible laser diodes operating at 650nm in an opto mechanical scanner resulting in less than 3 9uW radiated power as observed through a 7mm aperture and averaged over 10 seconds Do not attempt to remove the protective housing of the scanner as unscanned laser light with a peak output up to 0 8mW would be accessible inside Laser Light Viewing The scan window is the only aperture through which laser light may be observed from this product A failure of the scanner motor while the laser diode continues to emit a laser beam may cause emission levels to exceed those for safe operation The scanner has safeguards to prevent this occurrence If however a stationary laser beam is emitted the failing scanner should be disconnected from its power source immediately Adjustments Do not attempt any adjustments or alteration of this product Do not remove the protective housing of the scanner There are no user serviceable parts inside Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure Optical The use of optical instruments with this product will increase th
11. e eye hazard Optical instruments include binoculars magnifying glasses and microscopes but do not include normal eye glasses worn by the user For CE Countries This scanner is in conformity with CE standards Please note that an approved CE marked power supply unit should be used in order to maintain CE conformance Dual Laser Omnidirectional Vertical Scanner ji Table of Contents PUNO ELAN NOUE Em PERO CU CLONE saanane awk wi ia a aaa NA a eg Aa a aaa uuu 1 UHDBCKIDB asana ka aa EA unten icerum te OE AE a NR Ka NA AAT e ea Tem Ee a kk aana UE 1 Finding Your Way Around 0seeeeeeeeeeneenaeenen an aea naen ana nan an naen a anana nenen n aane ena nane e nana Ser up Ras EU ORIS INS 2 Connected MOUNTE saa gaen gara Nk kaeh NGA RAN BAGAN KING E Ena a SANG E TAN NUN HDI RE LA pa Ga Ban I VENIR 2 PON ET saanak 2 Verifying Scanner Operation ccccceccceseccssccceececescceeceeeceenecsencesenceteuseeeeceeeess 3 NA OLENG OU 4 Mounting Plate Installation eeeeeeseeeeeeeeeeenee nee aee nana MR ee nenen e naen e eaaa EISE 5 Auxiliary Handheld Scanner Connection optional eese 6 BC eire laria RE T 7 Connecting to the HOST RERUM 7 Setting Up the ScCanner ssssssssssses
12. f the system and scanner do not match Adjust the set tings so they match The communication cable does not suit your POS system Contact your dealer for the cor rect communication cable The software running on the POS system does not support the data format of the bar code label Dual Laser Omnidirectional Vertical Scanner 20 21 UsER s MANUAL scale 1 1 a TA Mounting Plate Boring Template Dual Laser Omnidirectional Vertical Scanner
13. nidirectional Vertical Scanner USER S MANUAL 2 Insert the 8 pin modular plug of the power link cable into the host connector in the back of the scanner until a firm click is heard HOST EAS AUX 14 J M g 3 Plug the power adapter into the jack on the power link cable See page 2 Figure 4 Plug the AC end of the power adapter into an AC outlet The scanner powers up the buzzer sounds four beeps and the LED indicator glows blue 5 Present a known good test barcode to the scanner The scanner should issue a short beep and the LED should flash red momentarily If the scan ner is connected to a keyboard wedge for this test it should read one bar code beep then remain with a red LED indicating light This is normal when the keyboard wedge is not connected to a live host terminal Note If the scanner does not produce any beeps or produces the wrong beeps or the LED does not light remove the power connection and refer to the section on Troubleshooting Mounting After the scanner passes its verification test section above proceed with mounting The scanner should be installed in a location away from direct sunlight high levels of ambient light reduce scanner effectiveness The two basic styles of mounting are a with the included mounting plate and b with a custom bracket not included for back mounting If an auxiliary hand held scanner is to be attached it must be properly connected as part
14. nsert the 8 pin modular plug of the power link cable into the host connector in the back of the scanner until it clicks 7 Mate the scanner and the mounting plate engaging the tab on the under side Be careful not to pinch the cable 8 Replace the mounting plate screws 9 Plugthe new cable into the host 10 If a power adapter is used plug the power adapter into the jack on the interface cable 13 Dual Laser Omnidirectional Vertical Scanner UsER s MANUAL Specifications OPERATIONAL Light Source Dual 650nm visible laser diodes Depth of Scan Field 0 216mm Width of Scan Field 90mm 9 contact 218mm 216mm Number of Scan Lines 32 Scan Pattern Scan Speed Minimum Bar Width Print Contrast Indicators LED Decode Capability Beeper Operation System Interfaces PHYSICAL Height Depth Width Weight Cable 8 direction scan field 2400 scans per second 5mil PCS 9096 3096 UPC EAN 100 Two color LED blue amp red UPC EAN JAN UPC Versions A amp E EAN 8 EAN 13 JAN 8 JAN 13 ISBN ISSN Japanese Book land Code 39 with full ASCII Codabar NW7 Code 128 EAN 128 Code 93 Interleaved 2 of 5 Addendum 2 or 5 MSI Plessey China Post Code Code 32 Italian Pharmacode Optional IATA Code Industrial 2 of 5 Standard 2 of 5 Discrete 2 of 5 Matrix 2 of 5 Code 11 RSS 14 RSS Limited RSS Expanded Programmable tone and beep time Keyboard RS 232C USB1 1 Wand Aux RS 232 152mm 82mm
15. pt that type of barcode The host has disabled the scanner Check host setup The barcode type presented is not supported by the scanner The scanner is on but The scanner has entered into the the motor IS not sleep mode Press the push button on the front running the facet wheel is of the scanner to wake up the scanner or not rotating A barcode cannot present an object close to the scan window be read The LED IS intermittently flashing blue The LED remains red Possible failure of the scanning safeguard and blue circuit Disconnect the scanner from its power source immediately and contact your dealer The scanner does not accept There is no proper handshaking with the POS more than two or three bar system Switch on the POS system code labels and check connection and communication set tings A stray barcode is sitting somewhere in the scanner field of view Remove all barcode labels from the scanner s scan volume and try again The scanner cannot send the data to the POS system Make sure that all cables are connected and your POS system is ready to receive data 19 Dual Laser Omnidirectional Vertical Scanner USER S MANUAL Problem A barcode is read by the scanner but not accepted by the POS system Diagnostic Tips The communication cable is not connected to the correct port of your POS system Refer to the manual of your POS system to locate the serial port The communication settings o
16. serssessersressersrrssessrrssessrrsrerserseersersersresserseeeserseeeseesersrerseesersserseeerense 8 elec 2 AENA E T A NA KEN 8 DENK o E EE E E E E E E E aaa a 8 ODEON erna EAEE A vs NB A NB ANA A EE A EEE AA E AEE AATE 9 LED ANGSA ON eE E E E TEE 9 Beeps 10 Changing the Beep VOlUMm sasasi anana aa ina aa Na Aa ONE SANG a NE ea oni niei KAR Na A Ka GA NE AAN BA aaa a a anaiak 10 SS DOS erer MEC RTT AAN A NGON TYETA ANARA TONI NE NGRE KUA 11 Controlling the Scanner from a POS System ccccceseccesseccsecceeneceeseeceneceensceceuceeeneeeeeecenenees 11 Connecting to EAS System Optional ccsessseresssssscccusrencacscuseussencususenacsseneusasscausreneusrenee 12 Maintaining the Scanner qasecessiesi niei uos end TP Sa bRT UP SY PUn nean eaaa FE ad DoD Eeka Se a URN rp nane ene anana een n naen EN A 13 Cleaning tne Scan WiIIndOWaoucasematinciecun anis sot naen uk bin Ista cibo es OcolKko corona RN DE Obr SERE OE DER RE PM eee 13 Replacing the Interface C dDIBs estimer Ersten vic tom esed in Fes ce genus ro a nana na S ER nana ne nenen a nean dicor i naen 13 PECI CA OMS PREDICT 14 PGI NS O a sures tera we tesa cba Ka sca RAGA KIE OU Emm 16 PUGS SIE NING Sia aa aka a apaa ah wa aa a aa a Aa Aa aa Kb E aa aa Ga Kh BEK M pM BERGADA D NENEK KN KAR NE PR MIND MAKA 18 TET UNOS TO OU ooo aga a e EI IM BANGER GA BA RA GG a DU Ga a aaa EM aka aana aaa I a unc 19 iii Dual Laser Omnidirectional Vertical Scanner Introduction
17. tor push button mount holes scan window host POS AC adapter optional terminal auxiliary scanner d Jj Connecting and Mounting Power The scanner requires a minimum of 300mA at 5 V DC power The interface cable that comes with the scanner supports both direct power where the scanner takes power from the host machine and external power that s what the sup plied power adapter is for A sufficiently robust POS system can support a scanner successfully without external power a POS system with a barely adequate power supply may produce erratic performance either of the POS sys tem itself or of the scanner or both when a scanner is attached Dual Laser Omnidirectional Vertical Scanner 2 USER S MANUAL Unless you are sure your POS system can handlethe load itisrecommended that you use the supplied power adapter When an external adapter is connected the scan ner does not take power from the host The scanner turns on when power is supplied and turns off when power is removed There is no on off switch on the scanner itself Use only an AC DC power adapter approved for the scanner Use of other power supplies may cause damage to the product and void the factory warranty Verifying Scanner Operation Before mounting your scanner please follow the procedure below to verify scanning operation 1 Take out the screws and remove the mounting plate Remove Mounting Plate 3 Dual Laser Om
18. urn the unit for repair Alternate flashing red and blue The scanner detects failing power Please light check the power supply 9 Dual Laser Omnidirectional Vertical Scanner USER S MANUAL Beeps A beeper gives audible feedback on scanner operation Beeps Indication A barcode has been successfully decoded Four beeps in series This indicates the scanner passed the power on self test and is operating properly Two beeps low high The scanner has entered programming mode Two beeps same tone Scanner has returned from programming to normal mode This is a failure indication Return the unit for repair Changing the Beep Volume The scanner can be programmed with the Programming Guide to change beeper tone volume and duration the beeper volume can also be changed by using the push button The default beep volume is loud There are three sound levels loud medium and low Press and hold the push button for about 5 seconds The scanner will cycle to its next level Repeat till the desired level is reached Note The volume setting is saved in volatile memory That means the change will lost when the scanner powers down On next power up the scanner resets to the configured setting If you wish to keep the changed the volume setting use the Programming Guide to set the changes Dual Laser Omnidirectional Vertical Scanner 10 Sleep Mode After the scanner has been inactive for a period of time the laser
Download Pdf Manuals
Related Search