CL1PAD1 Power Adapter Model User`s Manual
Contents
1. The minimum operating voltage of each module connected to the power adapter is 20 4 V therefore supply voltage subtracted by the voltage drop should be equivalent to or more than 20 4 V 4 1 System power calculation method 4 1 1 Current consumption calculation Current Total current Total current consumption consumption __ consumption of of YO equipment such lt A in CC LinkLT each module in 26 ee lt 5 system CG Link LT system communication cable 1 1 Some remote I O modules for CC Link LT supply the power for I O via the flat cable dedicated to CC Link LT For the details refer to the instruction manual of each remote I O module 4 1 2 Voltage drop Calculate the voltage drop based on the simplified graph or the calculation formula supply voltage 24V DC ambient temperature 20 C Current consumption A One power adapter is allowed within the range shown in the graph above 2 Selection based on the calculation formula Maximum Voltage i Constant Total current distance m x x r lt 3 6V drop V Constant 14 0 06 consumption A Maximum z distance Furthest station from the power adapter Total current consumption of each module in CC Link LT F system Total current consumption of I O equipment such as sensors to which power is supplied via communication cable 1 Total current consumption 1 Some remote I O mod2. MITSUBISHI ELECTRIC JAPANESE ENGLISH CL1PAD1 Power Adapter Model Thank you very much for purchasing this product Please read this manual thoroughly before starting to use the product and handle the product properly Users Manual MODEL CLIPADT CC a LT MANUAL Number JY997D04601F Link Date April 2015 SAFETY PRECAUTIONS Read these precautions before using Please read this manual carefully and pay special attention to safely in order to handle this product properly Also pay careful attention to safely and handle the module properly These precautions apply only to Mitsubishi equipment Refer to the user s manual of the CPU module to use for a description of the PLC system safety precautions These SAFETY PRECAUTIONS classify the safety precautions into two categories WARNING and CAUTION Procedures which may lead to a dangerous condition Z WARNING and cause death or serious injury if not carried out properly Procedures which may lead to a dangerous condition Z CAUTION and cause superficial to medium injury or physical damage only if not carried out properly Depending on circumstances procedures indicated by A CAUTION may also be linked to serious results In any case it is important to follow the directions for usage Store this manual in a safe place so that you can take it out and read it whenever necessary
3. Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi machine damage or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties A For safe use This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system EA Country Region Sales office Tel Country Region Sales office Tel USA Mitsubishi Electric Automation Inc South Africa CBl Electric Brazil MELCO TEC Representacao Comercial e No 1386 Hongqiao Road Mitsubishi Electric Assessoria Tecnica Ltda Automation Center Changning District Av Paulis
4. RF Immunity Fast transients ESD and Equipment requirements and tests Damped oscillatory wave C mase _ CLIPADI LINKs 24g Power op 28 G E3 l rF o LINK connector 2 4 5 mounting hole Terminal arrangement M4 mounting screw LINK POWER connector 5 Zl 6 lk Name Description Status A A i indicator LED POWER Lit while the power is supplied LINK DB For communication connector DA For communication 24G Power supply for communication LINK POWER DB For communication connector DA For communication 24V_ Power supply for communication Interface Name Description Supplies power from outside to power adapter Input voltage 28 8V DC or less 24G depending on connected model Rated input current 5 0 A Use a proper external power L supply under consideration of initial current of remote I O modules 24V Power terminal 2 2 Handling of LINK connector and LINK POWER connector Master module External power supply 1 LINK connector 2 LINK POWER connector LINK connector Executes only communication does not supply power Used when two or more power adapters are used in the CC Link LT system LINK POWER connector Executes communication and supplies the power to the CC Link LT system 3 Specifications 1 Ge
5. by the general Mitsubishi Electric Europe B V 1 Frequency Acceleration Half amplitude specifications in this manual ii il i 10 to 57Hz 0 075mm A i f the power adapter is used in any environment outside the range for the Gothaer Str 8 40880 Ratingen Germany Name Description Maraton 10 times in Kape i z E F n Pp i 57 to 150Hz 9 8m s2 general specifications electrical shock fire malfunction product Standards with which this product complies Status resistance 1 each of X Y damage or product deterioration may occur Type Programmable Controller Open Type Equipment irae POWER Lit while the power is supplied Continuous vibration is present andZ Do not directly touch the conductive area of the power adapter Models Products manufactured indicator LED Frequency Acceleration Half amplitude directions Malfunction or damage of the power adapter may be caused by such from November 1st 2002 to April 30th 2006 are compliant with LINK DB For communication 80 min touching EN61000 6 4 and EN61131 2 1994 A11 1996 A12 2000 connector DA For communication 1057M _ 0035mm securely fix the power adapter with DIN roll or mounting screws after May 1st 2006 are compliant with EN61131 2 2007 24G Power supply for communication 57 to 150Hz 4 9m s2 ecurely tighten the mounting screws within the specified torque range 7 HIR Interf E T 75 P a f the screws are insufficiently tightened the power adapter may drop Ferrata Remark
6. power adapter is allowed within the range shown in the graph above Selection based on the calculation formula Voltage _ Bheegi x Constant x Total current lt 3 6V drop V Constant 14 10 06 consumption A Y Maximum distance Furthest station from the power adapter Total current consumption of each module in CC Link LT F system Total current consumption of I O equipment such as sensors to which power is supplied via communication cable 1 Total current consumption Some remote I O modules for CC Link LT supply the power for I O via the flat cable dedicated to CC Link LT For the details refer to the instruction manual of each remote I O module The simplified graph and the calculation formula concerning voltage drop calculations may not be accurate depending on the ambient temperature and the number of used connectors dedicated to CC Link LT If the driving voltage 20 4V cannot be assured in a used remote I O module add another power adapter Installation The power adapter can be installed to a DIN rail or directly installed with screws Each installation procedure is described below 5 1 Installation direction Do not install the power adapter on the floor surface the ceiling surface or in the vertical direction If the power adapter is installed on such a surface or in such a direction its temperature may rise Make sure to install the power adapter on the wall horizonta
7. power supply outside the power adapter before cleaning or tightening the terminal screws If all phases are not shut down the power adapter may fail or malfunction Z CAUTION Do not disassemble or modify the power adapter Failure malfunction injury or fire may be caused by disassembly or modification The power adapter case is made of resin Do not drop it Do not apply strong impact to it The power adapter may be damaged by dropping or strong impact Shut down all phases of the power supply outside the power adapter before attaching or removing the power adapter to from the panel If all phases are not shut down the power adapter may fail or malfunction DISPOSAL PRECAUTIONS Z CAUTION e When disposing of the product treat it as an industrial waste TRANSPORTATION AND MAINTENANCE PRECAUTIONS Z CAUTION Electromagnetic Compatibility Standards EMC Remark Compliance with all relevant aspects of the standard Radiated Emissions Conducted Emissions Radiated electromagnetic field Fast transient burst Electrostatic discharge High energy surge Voltage drops and interruptions Conducted RF and Power frequency magnetic field EN61131 2 2007 Programmable controllers Equipment requirements and tests For more details please contact the local Mitsubishi Electric sales site e Notes for compliance to EMC LVD regulation It is necessary to install the CL1 series m
8. terminal Crimp style 4 Crimp style Terminal screw terminal Terminal screw terminal c 7 Terminal Terminal Tighten the terminal screws M3 screws on the terminal block with a tightening torque of 0 42 to 0 58 N m Do not tighten terminal screws exceeding the specified torque Failure to do so may cause short circuit equipment failures or malfunctions e RAV1 25 3 Applicable crimp e V1 25 3 manufactured by JST Mfg Co Ltd istyle terminal e 1 25 3 and TG1 25 3 manufactured by NICHIFU Co Ltd Applicable wire h 0 3 to 1 25 mm2 lsize 6 Power Wiring LINK LINK POWER Connector for Power adapter Connector for CC Link LT CC Link LT interface interface __ IH i 24V DA DA DB DB if 24G Internal circuit External power supply 24V DC 5A or less toe 24V I 24G Grounding 10092 or less Terminal block for power adapter e The external power supply is to be provided by the user e Use a proper external power supply with consideration for total current consumption and total initial current of remote I O modules and I O equipment such as sensors connected to the power adapter This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi
9. 00 China Mitsubishi Electric Automation China Ltd Brazil MELCO TEC Representacao Comercial e No 1386 Hongqiao Road Mitsubishi Electric Assessoria Tecnica Ltda Automation Center Changning District Av Paulista 1439 cj74 Bela Vista Sao Shanghai China Paulo CEP 01311 200 SP Brazil Tel 86 21 2322 3030 Tel 55 11 3146 2200 Taiwan Setsuyo Enterprise Co Ltd Germany Mitsubishi Electric Europe B V German Branch 6F No 105 Wugong 3rd Road Wugu District Gothaer Strasse 8 D 40880 Ratingen Germany New Taipei City 24889 Taiwan R O C Tel 49 2102 486 0 Tel 886 2 2299 2499 UK Mitsubishi Electric Europe B V UK Branch Korea Mitsubishi Electric Automation Korea Co Ltd Travellers Lane Hatfield Hertfordshire 3F 1480 6 Gayang Dong Gangseo Gu AL10 8XB UK Seoul 157 200 Korea Tel 44 1707 27 6100 Tel 82 2 3660 9530 Italy Mitsubishi Electric Europe B V Italian Branch Singapore Mitsubishi Electric Asia Pte Ltd Industrial Viale Colleoni 7 20864 Agrate Brianza Division Milano Italy 307 Alexandra Road Mitsubishi Electric Tel 39 039 60531 Building Singapore 159943 Spain Mitsubishi Electric Europe B V Spanish Branch Tel 65 6470 2308 Carretera de Rubi 76 80 AC 420 E 08190 Thailand Mitsubishi Electric Automation Thailand Sant Cugat del Valles Barcelona Spain Co Lid Tel 34 93 565 3131 Bang Chan Industrial Estate No 111 Soi France Mitsubishi Electric Europe B V French Branch Serithai 54 T Kannayao A
10. Always forward it to the end user DESIGN PRECAUTIONS Z WARNING e Depending on a failure in the remote I O module the output may become the ON or OFF status For output signals which can lead to a severe accident install a circuit monitoring them outside the module Z CAUTION Do not bind the control cable and the flat cable dedicated to CC Link LT together with the main circuit and the power cable Keep such cables far from the main circuit and the power cable Assure a distance of 100mm 3 94 or more Otherwise malfunction may be caused by noise Use the power adapter without applying any force on the connector for CC Link LT interface and the flat cable dedicated to CC Link LT Otherwise such cables may be broken or fail INSTALLATION PRECAUTIONS CAUTION e Use the power adapter within an environment described by the general specifications in this manual f the power adapter is used in any environment outside the range for the general specifications electrical shock fire malfunction product damage or product deterioration may occur e Do not directly touch the conductive area of the power adapter Malfunction or damage of the power adapter may be caused by such touching e Securely fix the power adapter with DIN rail or mounting screws Securely tighten the mounting screws within the specified torque range f the screws are insufficiently tightened the power adapter may drop short circuit or malfuncti
11. ECAUTIONS Z WARNING e Do not touch the terminals while the power is being supplied Electrical shock or malfunction may be caused by such touching Shut down all phases of the power supply outside the power adapter before cleaning or tightening the terminal screws If all phases are not shut down the power adapter may fail or malfunction CAUTION Do not disassemble or modify the power adapter Failure malfunction injury or fire may be caused by disassembly or modification The power adapter case is made of resin Do not drop it Do not apply strong impact to it The power adapter may be damaged by dropping or strong impact Shut down all phases of the power supply outside the power adapter before attaching or removing the power adapter to from the panel If all phases are not shut down the power adapter may fail or malfunction DISPOSAL PRECAUTIONS Z CAUTION e When disposing of the product treat it as an industrial waste TRANSPORTATION AND MAINTENANCE PRECAUTIONS Z CAUTION Electromagnetic Compatibility Standards EMC Remark Compliance with all relevant aspects of the standard Radiated Emissions Conducted Emissions Radiated electromagnetic field Fast transient burst Electrostatic discharge High energy surge Voltage drops and interruptions Conducted RF and Power frequency magnetic field For more details please contact the local Mitsubishi Electric sale
12. Kannayao 25 Boulevard des Bouvets F 92741 Bangkok 10230 Thailand Nanterre Cedex France Tel 66 2906 3238 Tel 33 1 5568 5568 Indonesia P T Autoteknindo Sumber Makmur Muara Karang Selatan Block A Utara No 1 Kav No 11 Kawasan industri Pergudangan Jakarta Utara 14440 P O Box 5045 Indonesia Tel 62 21 663 0833 Mitsubishi Electric India Pvt Ltd 2nd Floor Tower A amp B Cyber Greens DLF Cyber City DLF Phase Ill Gurgaon 122002 Czech Republic Mitsubishi Electric Europe B V 0 s Czech office Avenir Business Park Radicka 751 113e 158 00 PrahaS Czech Republic Tel 420 251 551 470 Poland Mitsubishi Electric Europe B V Polish Branch India ul Krakowska 50 32 083 Balice Poland Tel 48 12 630 47 00 Russia Mitsubishi Electric Europe B V Russian Branch St Petersburg office Piskarevsky pr 2 bld 2 lit Sch BC Benua office 720 195027 St Petersburg Russia Tel 7 812 633 3497 MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN Haryana India Tel 91 124 463 0300 Mitsubishi Electric Australia Pty Ltd 348 Victoria Road PO BOX11 Rydalmere N S W 2116 Australia Tel 61 2 9684 7777 Australia Specifications subject to change without notice MITSUBISHI ELECTRIC JAPANESE ENGLISH CL1PAD1 Power Adapter Model Thank you very much for purchasing this product Please read this manual thoroug
13. censes Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi machine damage or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties A For safe use This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system E Country Region Sales office Tel Country Region Sales office Tel USA Mitsubishi Electric Automation Inc South Africa CBl Electric 500 Corporate Woods Parkway Vernon Private Bag 2016 ZA 1600 Isando South Africa Hills IL 60061 USA Tel 27 11 977 0770 Tel 1 847 478 21
14. ectric Europe B V 0 8 Czech office Avenir Business Park Radicka 751 113e 158 00 PrahaS Czech Republic Tel 420 251 551 470 Mitsubishi Electric Europe B V Polish Branch ul Krakowska 50 32 083 Balice Poland Tel 48 12 630 47 00 Mitsubishi Electric Europe B V Russian Branch St Petersburg office Piskarevsky pr 2 bld 2 lit Sch BC Benua office 720 195027 St Petersburg Russia Tel 7 812 633 3497 Indonesia Australia Private Bag 2016 ZA 1600 Isando South Africa Tel 27 11 977 0770 Mitsubishi Electric Automation China Ltd Bangkok 10230 Thailand Tel 66 2906 3238 P T Autoteknindo Sumber Makmur Muara Karang Selatan Block A Utara No 1 Kav No 11 Kawasan Industri Pergudangan Jakarta Utara 14440 P O Box 5045 Indonesia Tel 62 21 663 0833 Mitsubishi Electric India Pvt Ltd 2nd Floor Tower A amp B Cyber Greens DLF Cyber City DLF Phase lIl Gurgaon 122002 Haryana India Tel 91 124 463 0300 Mitsubishi Electric Australia Pty Ltd 348 Victoria Road PO BOX11 Rydalmere N S W 2116 Australia Tel 61 2 9684 7777 MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BUILDING 2 7 3 MARUNOUCHI CHIYODA KU TOKYO 100 8310 JAPAN When exported from Japan this manual does not require application to the Ministry of Economy Trade and Industry for service transaction permission Specifications subject to change without notice
15. ed around the altitude of 0 m 3280 10 FJ i If the module is used in such an environment it may fail 560 1 il 4 Center of DIN rail 3 It indicates in which wiring area from the public wiring net to the 1837 3 66 2 60 90 3 55 mechanical module inside the site the equipment is assumed to be O gt connected z The category II applies for example to equipment whose power is 100 Ho Ea S ERENCE le Pema A supplied from a fixed facility T 328 1 l 4 b The surge resistant voltage of equipment whose rating is up to 300V is 2 masse o 2 500V S EJ 2 ciran rome z 4 This index indicates the degree of generation of conductive substances in Z 4 y Link 35 Fa 4 the environment in which the module is used The degree of contamination S 3 H 2 2 indicates that contamination is caused by generation of only non 2 10 lt _ 2 a L cy conductive substances 2 32 10 In this degree however temporary conduction may be caused by 3 Applicable DIN 5 Fome E accidental condensation g rail TH35 7 5Fe and TH35 7 5Al a gi b a 2 Performance specifications 5 a Q SCooIP f T a Ttem Specification x 5 3 Direct installation a 2 4 5 0 18 mounting Voltage input range Depends on the connected model 28 8V DC max as Screw tighten the power adapter by tightening M4 screws to the upper and Bl hole M4 mounting screw _ Mass Weight 0 26kg 0 58Ibs 5 0A lower mounting holes two holes in all provided in the power ada
16. ent whose power is supplied from a fixed facility The surge resistant voltage of equipment whose rating is up to 300V is 2 500V 4 This index indicates the degree of generation of conductive substances in the environment in which the module is used The degree of contamination 2 indicates that contamination is caused by generation of only non conductive substances In this degree however temporary conduction may be caused by accidental condensation 2 Performance specifications Item Specification Voltage input range Depends on the connected model 28 8V DC max 5 0A Use the power adapter in the range in which the total current consumption of each unit does not exceed the maximum rated current while the power is supplied except the period immediately after the power is turned on 10MQ between the external terminals as a whole and the ground terminal by 500V DC megger Supplies power from outside to power adapter 3 points M3 screws on terminal block Communication line module power supply module Compatible with flat cable dedicated to CC Link LT Max rated current Insulation resistance External connection method Connector with 4 pins dedicated to CC Link LT x 2 4 Construction Cautions Installation of power adapters At least one power adapter is required per CC Link LT system When constructing the system using only one power adapter the following three conditions sh
17. hly before starting to use the product and handle the product properly Users Manual MODEL CLIPADT CC IT MANUAL Number JY997D04601F Link Date April 2015 SAFETY PRECAUTIONS Read these precautions before using Please read this manual carefully and pay special attention to safely in order to handle this product properly Also pay careful attention to safely and handle the module properly These precautions apply only to Mitsubishi equipment Refer to the user s manual of the CPU module to use for a description of the PLC system safety precautions These SAFETY PRECAUTIONS classify the safety precautions into two categories WARNING and CAUTION Procedures which may lead to a dangerous condition and cause death or serious injury if not carried out properly Procedures which may lead to a dangerous condition and cause superficial to medium injury or physical damage only if not carried out properly N WARNING Z CAUTION Depending on circumstances procedures indicated by A CAUTION may also be linked to serious results In any case it is important to follow the directions for usage Store this manual in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user DESIGN PRECAUTIONS Z WARNING e Depending on a failure in the remote I O module the output may become the ON or OFF statu
18. ing transportation avoid any impact as the module is a precision instrument Doing so could cause trouble in the module e If is necessary to check the operation of module after transportation in case of any impact damage Notification of CE marking This notification does not guarantee that an entire mechanical module produced in accordance with the contents of the notification comply with the following standards Compliance to EMC standards of the entire mechanical module should be checked by the user manufacturer Attention This product is designed for use in industrial applications Note e Authorized Representative in the European Community Mitsubishi Electric Europe B V Gothaer Str 8 40880 Ratingen Germany Standards with which this product complies Type Programmable Controller Open Type Equipment Models Products manufactured from November 1st 2002 to April 30th 2006 are compliant with EN61000 6 4 and EN61131 2 1994 A11 1996 A12 2000 after May 1st 2006 are compliant with EN61131 2 2007 Electromagnetic Compatibility Standards EMC Remark EN61000 6 4 2001 Electromagnetic compatibility standard Generic standards Emission Radiated Emissions and Mains Terminal standard for Industrial environment Voltage Emissions Compliance with all relevant aspects of the EN61131 2 1994 A11 1996 A12 2000 Compliance with all relevant aspects of the standard Programmable controllers A f
19. l cable and the flat cable dedicated to CC Link LT of any impact damage BR lt lt Ambient storage together with the main circuit and the power cable Keep such cables far Notification of CE marking 25 to 75 C 13 to 167 F from the main circuit and the power cable Assure a distance of 100mm R a go temperature 3 94 or more This notification does not guarantee that an entire mechanical module produced eaa Ambient operating 5 to 95 RH Dew condensation shall not be Otherwise malfunction may be caused by noise in accordance with the contents of the notification comply with the following rome pa lt humidit lowed Use the power adapter without applying any force on the connector for standards Compliance to EMC standards of the entire mechanical module bal om leet each tt ae alowed i CC Link LT interface and the flat cable dedicated to CC Link LT should be checked by the user manufacturer S iad plani storage 5 to 95 RH Dew condensation shall not be Otherwise such cables may be broken or fail Attention Gp UNK i E humidity allowed s x Pa y PR i connector Terminal arrangement Number of INSTALLATION PRECAUTIONS This product is designed for use in industrial applications 2 4 5 mounting hole i Note M4 mounting screw LINK POWER connector Intermittent vibration is present sweep lt x ti Z CAUTION e Authorized Representative in the European Community 6 mS e Use the power adapter winn an environment described
20. lly 5 2 Installation to DIN rail Align the upper DIN rail installation groove in the power adapter with the DIN rail 1 and press the power adapter in that status 2 When removing the power adapter pull downward the hook for installation to DIN rail 3 then remove the power adapter 4 Installation Removal 1 4 l H g Applicable DIN rail TH35 7 5Fe and TH35 7 5Al 5 3 Direct installation lower mounting holes two holes in all provided in the power adapter for each module M4 x 0 7mm 0 03 x 16mm 0 63 or more pobligekibeaian Tightening torque range 0 78 to 1 08 N m 5 4 Crimp style terminal For the I O wiring use crimp style terminals of the following dimensions 3 2 0 13 6 2 mm 0 24 or less y 63 2 0 13 6 2 mm 0 24 or less When wiring one cable to one terminal When wiring two cables to one terminal i Crimp style Crimp style Terminal screw terminal Terminal screw terminal Terminal Terminal e Tighten the terminal screws M3 screws on the terminal block with a tightening torque of 0 42 to 0 58 N m Do not tighten terminal screws exceeding the specified torque Failure to do so may cause short circuit equipment failures or malfunctions e RAV1 25 3 Applicable crimp V1 25 3 manufactured by JST Mfg Co Ltd style terminal e 1 25 3 and TG1 25 3 ma
21. neral specifications Item Specification EEA 0 to 55 C 32 to 131 F Ambient storage 95 0 75 C 13 to 167 F temperature Ambient operating 5 to 95 RH Dew condensation shall not be humidity allowed Ambient storage 5 to 95 RH Dew condensation shall not be humidity allowed Number of Intermittent vibration is present sweep times Frequency Acceleration Half amplitude Vibration 10 to 57Hz 0 075mm 10 times in resistance 1 57 to 150Hz 9 8m s2 each of X Y Continuous vibration is present andZ Frequency Acceleration Half amplitude directions 10 to 57Hz 0 035mm 80 min 57 to 150Hz 4 9m s2 Impact resistance 1 147 m s2 3 times in each of X Y and Z directions es Corrosive gas should not be present Operating altitude Installation place Over voltage category Degree of contamination 2 000m 6561 8 or less 2 Inside control panel II or less 3 2 or less 4 1 The criterion is shown in IEC61131 2 2 The module cannot be used in an environment pressurized above the atmospheric pressure which can be generated around the altitude of 0 m If the module is used in such an environment it may fail 3 It indicates in which wiring area from the public wiring net to the mechanical module inside the site the equipment is assumed to be connected The category II applies for example to equipm
22. nterface LINK POWER DB For communication Impact resistance 1 147 m s2 3 times in each of X Y and Z directions short circuit or malfunction Foal i f the screws are excessively tightened the screws may be damaged EN61000 6 4 2001 Compliance with all relevant aspects of the connector DA For communication bain Corrosive gas should not be present and the power adapter may drop or short circuit Electromagnetic compatibility standard 24V_ Power supply for communication PIMOSRDEre m Generic standards Emission adiated Emissions and Mains Terminal perating altitude 000m or less nstall the power adapter on to a flat surface G at df Ne a issi Fe di a issi d Mains Terminal g i nitua 2 000m 6561 8 or 2 If the mounting surface is concave and or convex and if excessive force standard for Industrial environment Voltage Emissions Installation place Inside control panel is applied on the PC board nonconformity may occur EN64131 2 1994 A14 1996 A12 2000 Compliance with all relevant aspects of the Over voltage z Programmani cone d test RF Immunity Fast transients ESD and category Moree Equipment requirements and tests amped oscillatory wave Degree of 7 he 2 or less 4 contamination 1 The criterion is shown in IEC61131 2 1 Selection based on the simplified graph 7 Outside Dimensions 2 The module cannot be used in an environment pressurized above the 1000 Installation Removal tinficraminenes atmospheric pressure which can be generat
23. nufactured by NICHIFU Co Ltd Applicable wire A 0 3 to 1 25 mm2 lsize 6 Power Wiring LINK LINK POWER Connector for __Power adapter Connector for CC Link LT CC Link LT interface interface __ 1H 24V DA DA DB DB Fi 1H 24G Internal External power supply circuit 24V DC 5A or less 24V I 24G Grounding 10092 or less Terminal block for power adapter e The external power supply is to be provided by the user e Use a proper external power supply with consideration for total current consumption and total initial current of remote I O modules and I O equipment such as sensors connected to the power adapter Screw tighten the power adapter by tightening M4 screws to the upper and install the module so that the clearance of 1 to 2mm 0 04 to 0 08 is assured 7 Outside Dimensions Unit mm inches Center of DIN rail 66 2 60 90 3 55 10 0 40 Ha En ew eee ae 2 5 MERE POWER O i o z t N i z time 2 4 a al Ko A D a O 2 N LINKS 24G in pone 38 J N 24V a tear g 2 64 5 0 18 mounting Bl hole M4 mounting screw Mass Weight 0 26kg 0 58Ibs This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent li
24. odule in a shielded metal control panel Use this product in Zone A as defined in EN61131 2 1 Zone defined in EN61131 2 Separation defined in EN61131 2 for EMC LVD regulation decided depending on condition in industrial setting Zone C Factory mains which is isolated from public mains by dedicated transformers Zone B Dedicated power distribution which is protected by secondary surge protection 300V or less in the rated voltage is assumed Zone A Local power distribution which is isolated from dedicated power distribution by AC DC converters isolation transformers etc 120V or less in the rated voltage is assumed e When the following models use the CC Link LT power adapter model CL1PAD1 a power line connecting to the external power supply terminal of the CL1PAD must be 30m 98 5 or less CL2AD4 B CL2DA2 B 1 Outline of Product This product is a power adapter connected to CC Link LT This product supplies 24V DC power from an external power supply to the CC Link LT system At least one power adapter is required per CC Link LT system 2 Name of Each Part 2 1 Name of each part and assignment Status indicator LED Power terminal DIN rail installation groove ne ave T C Name Description Supplies power from outside
25. on f the screws are excessively tightened the screws may be damaged and the power adapter may drop or short circuit nstall the power adapter on to a flat surface f the mounting surface is concave and or convex and if excessive force is applied on the PC board nonconformity may occur WIRING PRECAUTIONS WARNING Make sure to shut down all phases of the power supply outside the module before starting the installation or wiring work If all phases are not shut down electrical shock or product damage may be caused Z CAUTION Confirm the rated voltage and the terminal arrangement of the power adapter then correctly wire the power adapter If a power supply not conforming to the specification rating is connected or the power adapter is wired incorrectly fire failure or malfunction may occur e Tighten the terminal screws within the specified torque range If the terminal screws are insufficiently tightened fire or malfunction may occur If the terminal screws are excessively tightened the screws may be damaged and the module may short circuit equipment failures or malfunction Make sure that foreign objects such as cutting and wire chips do not enter the power adapter Fire failure or malfunction may be caused by the foreign objects e Attach a warning label hazard symbol 417 IEC 5036 concerning electric shock to the panel STARTING AND MAINTENANCE PR
26. ould be satisfied If the following two conditions are not satisfied use of two or more power adapters in constructing the system e The current capacity of the power adapter is 5A therefore total current consumption should be an equivalent to or less than 5 A e In order to operate the system in stable status the voltage drop should be equivalent to or less than 3 6 V The minimum operating voltage of each module connected to the power adapter is 20 4 V therefore supply voltage subtracted by the voltage drop should be equivalent to or more than 20 4 V 4 1 System power calculation method 4 1 1 Current consumption calculation Total current consumption Current Total current of I O equipment such consumption consumption of i inCC LinkLt eachmodule in a sensors to which lt 5A system CC Link LT system power is supplied via communication cable 1 1 Some remote I O modules for CC Link LT supply the power for I O via the flat cable dedicated to CC Link LT For the details refer to the instruction manual of each remote I O module 4 1 2 Voltage drop Calculate the voltage drop based on the simplified graph or the calculation formula supply voltage 24V DC ambient temperature 20 C 1 Selection based on the simplified graph 2 ii 5 1000 8280 10 560 1837 3 100 328 1 10 32 10 Maximum cable length m inches 0 4 0 0 1 1 0 10 Current consumption A One
27. pter Use the power adapter in the range in which the install the module so that the clearance of 1 to 2mm 0 04 to 0 08 is assured total current consumption of each unit does not for each module Max rated current A i exceed the maximum rated current while the power kaa M4 x 0 7mm 0 03 x T6mm 0 63 or more is supplied except the period immediately after the 0 1 Lelideareeed ahaa Tightening torque range 0 78 to 1 08 N m power is turned on 0 4 o1 10 10 10MQ between the external terminals as a whole and the ground terminal by 500V DC megger Supplies power from outside to power adapter 3 points M3 screws on terminal block Communication line module power supply module Compatible with flat cable dedicated to CC Link LT Connector with 4 pins dedicated to CC Link LT x 2 Insulation resistance External connection method 4 Construction Cautions Installation of power adapters At least one power adapter is required per CC Link LT system When constructing the system using only one power adapter the following three conditions should be satisfied If the following two conditions are not satisfied use of two or more power adapters in constructing the system e The current capacity of the power adapter is 5A therefore total current consumption should be an equivalent to or less than 5 A e In order to operate the system in stable status the voltage drop should be equivalent to or less than 3 6 V
28. s For output signals which can lead to a severe accident install a circuit monitoring them outside the module WIRING PRECAUTIONS WARNING Make sure to shut down all phases of the power supply outside the module before starting the installation or wiring work If all phases are not shut down electrical shock or product damage may be caused Z CAUTION Confirm the rated voltage and the terminal arrangement of the power adapter then correctly wire the power adapter If a power supply not conforming to the specification rating is connected or the power adapter is wired incorrectly fire failure or malfunction may occur e Tighten the terminal screws within the specified torque range If the terminal screws are insufficiently tightened fire or malfunction may occur If the terminal screws are excessively tightened the screws may be damaged and the module may short circuit equipment failures or malfunction Make sure that foreign objects such as cutting and wire chips do not enter the power adapter Fire failure or malfunction may be caused by the foreign objects e Attach a warning label hazard symbol 417 IEC 5036 concerning electric shock to the panel STARTING AND MAINTENANCE PRECAUTIONS Z WARNING e Do not touch the terminals while the power is being supplied Electrical shock or malfunction may be caused by such touching Shut down all phases of the
29. s site e Notes for compliance to EMC LVD regulation It is necessary to install the CL1 series module in a shielded metal control panel Use this product in Zone A as defined in EN61131 2 1 Zone defined in EN61131 2 Separation defined in EN61131 2 for EMC LVD regulation decided depending on condition in industrial setting Zone C Factory mains which is isolated from public mains by dedicated transformers Zone B Dedicated power distribution which is protected by secondary surge protection 300V or less in the rated voltage is assumed Zone A Local power distribution which is isolated from dedicated power distribution by AC DC converters isolation transformers etc 120V or less in the rated voltage is assumed e When the following models use the CC Link LT power adapter model CL1PAD1 a power line connecting to the external power supply terminal of the CL1PAD must be 30m 98 5 or less CL2AD4 B CL2DA2 B 1 Outline of Product This product is a power adapter connected to CC Link LT This product supplies 24V DC power from an external power supply to the CC Link LT system At least one power adapter is required per CC Link LT system 2 Name of Each Part EN61131 2 2007 Programmable controllers Equipment requirements and tests 2 1 Name of each part and assignment Status indicator LED Power terminal DIN rail installation groove fe ene Tz ne ave e Dur
30. ta 1439 cj74 Bela Vista Sao Shanghai China Paulo CEP 01311 200 SP Brazil Tel 86 21 2322 3030 Tel 55 11 3146 2200 Setsuyo Enterprise Co Ltd Germany Mitsubishi Electric Europe B V German Branch 6F No 105 Wugong 3rd Road Wugu District Gothaer Strasse 8 D 40880 Ratingen Germany New Taipei City 24889 Taiwan R O C Tel 49 2102 486 0 Tel 886 2 2299 2499 UK Mitsubishi Electric Europe B V UK Branch Mitsubishi Electric Automation Korea Co Ltd Travellers Lane Hatfield Hertfordshire 3F 1480 6 Gayang Dong Gangseo Gu AL10 8XB UK Seoul 157 200 Korea Tel 44 1707 27 6100 Tel 82 2 3660 9530 Italy Mitsubishi Electric Europe B V Italian Branch Singapore Mitsubishi Electric Asia Pte Ltd Industrial Viale Colleoni 7 20864 Agrate Brianza Division Milano Italy 307 Alexandra Road Mitsubishi Electric Tel 39 039 60531 Building Singapore 159943 Spain Mitsubishi Electric Europe B V Spanish Branch Tel 65 6470 2308 Carretera de Rubi 76 80 AC 420 E 08190 Thailand Mitsubishi Electric Automation Thailand Sant Cugat del Valles Barcelona Spain Co Ltd Tel 34 93 565 3131 Bang Chan Industrial Estate No 111 Soi France Mitsubishi Electric Europe B V French Branch Serithai 54 T Kannayao A Kannayao Czech Republic Poland Russia 500 Corporate Woods Parkway Vernon Hills IL 60061 USA Tel 1 847 478 2100 25 Boulevard des Bouvets F 92741 Nanterre Cedex France Tel 33 1 5568 5568 Mitsubishi El
31. to power adapter Input voltage 28 8V DC or less 24G depending on connected model Rated input current 5 0 A Use a proper external power L supply under consideration of initial current of remote I O modules 24V Power terminal 2 2 Handling of LINK connector and LINK POWER connector Master module External External power supply power supply 1 LINK connector 2 LINK POWER connector LINK connector Executes only communication does not supply power Used when two or more power adapters are used in the CC Link LT system LINK POWER connector Executes communication and supplies the power to the CC Link LT system 3 Specifications 1 General specifications During transportation avoid any impact as the module is a precision ie Item Specification instrument Doing so could cause trouble in the module CLIPADI ae ii Ambient working m i Z CAUTION If is necessary to check the operation of module after transportation in case 4 temperature 0 to 55 C 32 to 131 F Do not bind the contro
32. ules for CC Link LT supply the power for I O via the flat cable dedicated to CC Link LT For the details refer to the instruction manual of each remote I O module The simplified graph and the calculation formula concerning voltage drop calculations may not be accurate depending on the ambient temperature and the number of used connectors dedicated to CC Link LT If the driving voltage 20 4V cannot be assured in a used remote I O module add another power adapter 5 Installation The power adapter can be installed to a DIN rail or directly installed with screws Each installation procedure is described below 5 1 Installation direction Do not install the power adapter on the floor surface the ceiling surface or in the vertical direction If the power adapter is installed on such a surface or in such a direction its temperature may rise Make sure to install the power adapter on the wall horizontally 5 2 Installation to DIN rail Align the upper DIN rail installation groove in the power adapter with the DIN rail 1 and press the power adapter in that status 2 When removing the power adapter pull downward the hook for installation to DIN rail 3 then remove the power adapter 4 5 4 Crimp style terminal For the I O wiring use crimp style terminals of the following dimensions 3 2 0 13 3 2 0 13 6 2 mm 0 24 or less 6 2 mm 0 24 or less y When wiring one cable to one terminal When wiring two cables to one
Download Pdf Manuals
Related Search