cautions - CGP Electronics Kft.
Contents
1. PAPER Lamp Auto Paper Cutter CBM 291 oniy FEED Switch Printer Mechanism Mechanism Lock Lever Head Up Lever Paper Roll Setting Position Interface Connector for Power and Interface cable Dip Switch FG Terminal Rack Mounting Bracket 5 CITIZEN CBM 290 291 User s Manual 2 5 2 Explanation of each parts Front cover Open close this cover in case of paper change or paper jam Paper lamp Lights up when paper runs out Feed switch Press this switch to feed the paper Pressing this switch keeps paper feeding continuously Mechanism lock lever This lock lever is used to pull down the printer mechanism to lift up the print head and to remove the paper manually Or move the cutter blade in case the cutter blade is locked due to paper jam Head up lever This is the lever to lift up print head Cutter blade For CBM 290 Used to cut the paper manually Mounting bracket Used to mount this equipment on the rack etc Interface connector Connect a cable for power supply and interface to this connector DIP switch Used to set the initial setting such as the type of interface serial parallel or print density etc FG terminal Used to earth the frame of main body Connect it properly Auto paper cutter CBM 291 only Paper is cut automatically by command Complete full cut or partial cut one tear point remains can be specified 6 CITIZEN CBM 292. 22 1 6 Buffermng ette e ete buh beled 22 T T Electrical Characteristics ert toU nee Is aan sa 22 9 Print Control Function essessesoesnessenesnssnesnensonennesnensenennesnennensnnennesnennenennenssnensnnenennenesnsnsenensnensenesnesnssnenssnesnssnsnnene 24 9 1 Command Tt s oe Rot e ten eet sedo ut 24 9 2 Command Details ineo DH Heo e e ehe nase reete 25 10 Character 42 10 1 International a nire rete tente Brei ie Ae e Ptr de Pies ete elite 42 10 2 International Character Code Table u 22022202220220022002200nnnonnnonnsonnnnnnonnonnonssonsennsonnennsennennennnn 43 Appendix 1 Block EPIIT EDD 44 Appendix 2 45 CITIZEN CBM 290 291 User s Manual 1 OUTLINE CBM 290 is a Line Thermal printer which can be equipped in a rack and is widely used for various data communication POS terminal and various measurement devices This printer can be used for various applications since abundant functions are incorporated Prior to actual use please read this instruction manual carefully for your correct understanding 1 1 Features 1 Ultra small sized rack mounting line thermal printer 2 High speed and quite printing 3 High reliability due to the long
3. BE Canceling double printing Specifying double printing The print result of Double printing and highlight character printing is completely same 16 Printing and feeding paper at minimum pitch ESC J n Code 1B h 4A h 0 lt lt Data is described in Hex code Prints data inside the print buffer and feeds paper by n 360 inch e Specified volume does not remain beginning of the line is to be considered as the next printing start position e Initial value is not defined 17 Selecting International Characters ESC R n Code 1B h 52 h n 0 nx0A Data is described in Hex code Selecting international characters e Depending on the value of n following character sets are specified o je ae 1 2 Gemmy 4 Denmark Sweden 6 On oe e The initial value of n indicates the character set specified by Jumper setting J1 J3 30 CITIZEN CBM 290 291 User s Manual 18 NOP ESC c3 19 NOP ESC c5 20 Enabling Disabling Panel Switch ESC c 5n Code 1B h 63 h 35 h n 0 lt lt Data 15 described in Hex code Selecting the LF switch valid invalid e is valid only in the lowest bit nO e bit means the followings LF SW valid LF SW invalid e The initial value of n is 0 21 Printing and Feeding the paper by n lines ESC d n Code 1B h 64 h n 0
4. Code 1B h 25 h n 0 n lt FF data is described in Hex code Specifying canceling download characters Download characters and download bit images cannot be defined simultaneously Further only the lowest bit nO is valid for n The lowest bit nO indicates the following Canceling download character Specifying download character 7 Defining Download Character ESC amp s n m a DID2 Dn Code 1B h 26 h s n m a Dn 5 03 20 Hex lt 7E Hex 20 Hex m 7E Hex 0 lt a lt 0 Hex Defines the font of download characters of alphanumeric characters s indicates the number of bytes in vertical direction n indicates the start character code and m the end character code To define only one character set n m Character codes definable includes 95 ASCII codes in total between lt 20 gt lt 7E gt H a indicates the number of dots in horizontal direction for definition Dn is the data to be defined which indicate a pattern equal to a dot in horizontal direction from the left end The rest of the pattern on the right side is filled with space The rest of data to be defined is s x a Download characters thus defined remain valid until redefinition ESC execution GS execution or power OFF is practiced 26 CITIZEN CBM 290 291 User s Manual EXAMPLE LSB FONT A FONT B DI LSB 8 Specifying the Bit Image Mode ESC mnl
5. 1 is to be specified For example to set the position at 9th column n 8 is to be specified e tab position is set at position where it is character width x n from the line beginning The character width at this time includes the rightward space amount In double wide characters it is made double of the ordinary case e Tab positions can be specified are maximum 32 Specifying exceeding this is ignored e ESCD NUL clears all the set tab positions Following clearing horizontal tab command is ignored e Initial value is specified for each eight characters 9 17 25 33 of characters Specifying canceling highlighting ESC E n Code 1B h 45 h n 0 lt lt Data is described in Hex code Specifying canceling the highlighting characters e n is valid only for the lowest bit nO Control by the lowest bit nO is shown as follows o Canceling highlighting Specifying highlighting e Thisis effective to all characters e Dot configuration of a highlighted character includes one extra dot added at its side The print result of Double printing and highlight character printing is completely same 29 CITIZEN CBM 290 291 User s Manual 15 Specifying canceling Double Printing ESC G n Code 1B h 47 h n Q lt n lt FF Data 15 described in Hex code Specifying canceling the double printing e n is valid only for the lowest bit nO Control by n is shown as follows
6. 3 4 5 6 7 8 9 Norway dk er dt Denmark I vr 43 CITIZEN CBM 290 291 User s Manual Appendix 1 Block Diagram VF Parallel Centronics Serial RS 232C Power Supply OSC16 0MHz 291 Cutter Driver Operation Panel I 24 P GND 5V VCC RAM DIP Switch Diver Mechanism G A o Printer LT 282 Paper End Head Up Stepping Motor CITIZEN 44 CBM 290 291 User s Manual Appendix 2 Outer Appearance Installating space diameter POEM 9 0 0 103 Plate thickness 02 11 1 3mm 992 i 45 CITIZEN Japan CBM Corporation Information Systems RSS Bldg 5 68 10 Nakano Nakano ku Tokyo 164 0001 Japan Head Office Tel 81 3 5345 7540 Fax 81 3 5345 7541 04 99823 1000 0048 3000 Printed in Japan
7. CA 90501 U S A TEL 1 310 781 1460 FAX 1 310 781 9157 23 Other Areas Japan CBM Corporation Information Systems Division CBM Bldg 5 68 10 Nakano Nakano ku Tokyo 164 0001 Japan TEL 81 3 5345 7540 FAX 81 3 5345 7541 CITIZEN CBM 290 291 User s Manual 9 Print Control Function 9 1 Command Lit 5 1 Collective specifying printing mode 6 Specifying canceling download character set Defining download characters 8 Specifying the bit image mode o 9 c c4 c5 NOP NOP Selecting the font of HRT code o a NHK lt lt Selecting the font of HRI code Defining the download bit image Printing the download bit image Starting ending macro definition Executing the macro Executing the maero ESC m 3 E G J 3 t i 24 CITIZEN CBM 290 291 User s Manual 9 2 Command Details 1 Horizontal Tab Command HT Q 3 4 5 Code 09 h Shifts the printing position to the next horizontal tab position The horizontal tab position is set by ESC D Initial setting of the horizontal tab position is each 8 characters in 9th 17th 25th 33rd columns Print Command CR Code 0D h 1 When DS 1 2 is OFF This command is ignored 2 When DS 1 2 is ON With data held inside the internal print buffer printing and line feed are performed Without data inside the interna
8. Data is described in Hex code The printing start position is specified in the number of dots from the beginning of line 1 20 inch unit number of dots is divided by 256 whose quotient is taken as n2 and the residual as nl Therefore the printing start position is equal to nl n2 x 256 from the beginning of line e Specifying beyond the line end is ignored e Incase underline is specified no underline is provided to the skipped portion Specifying Relative Positions ESC XY nl n2 Code 1B h 5C h nl n2 OSnl lt FF 0 lt 2 lt Data is described in Hex code The printing start position is specified in the number of dots from the current position Rightward direction is taken as plus and leftward direction as minus e To specify N dot in minus left direction use a complement of N for assignment N dots 65536 number of dots is divided by 256 whose quotient is taken as n2 and the residual as nl e Specifying exceeding the end of line is ignored e Incase underline is specified no underline is provided to the skipped portion Bar Code Printing GS n Dn NUL Code 1D h 6B h n Dn 00 h 0 lt lt 7 Dataare described in Hex code Specifying a type of bar code and printing bar codes beginning of line is considered as the next printing start position e Depending on the value of n the following bar code can be selected Dn indicates a character
9. FH unseren VERTICAL DIRECTION HORIZONTAL DIRECTION 203 DPI 203 DPI KE Double wide mode 203 DPI 101 DPI Double high mode 101 DPI 203 DPI Double wide double high mode 101 DPI 101 DPI e When data exist inside the print buffer this command is ignored e When a download bit image has not been defined this command is ignored e A portion of a download bit image exceeding one line length is not printed e download character and a download bit image cannot be defined simultaneously 37 Starting Ending Macro Definition GS Code 1D h 3A h Specifying starting ending macro definition Maximum content available for macro definition is 2048 bytes A portion exceeding 2048 bytes is not defined e Even with ESC initialization of the printer having been executed defined content is not cleared Therefore it is possible to include ESC into the content of macro definition e Normal printing operation is carried out even while in macro definition 38 Macro Execution GS nl n2 n3 Code 1D h 5E h nl n2 n3 OSnl lt 0 lt n2 lt FF 0 lt 3 lt 1 Data is described in Hex code Executing contents defined in macro e nl n3 indicate as follows nl The number of times of macro execution n2 Waiting time on macro execution Waiting time of n2 x 100 msec is given for every execution n3 Macro execution mode Mode 0 Continuous execution Execution by LF SW 38
10. lt lt Data is described in Hex code Prints data inside the buffer and feeds paper by n lines e Specified line does not remain e beginning of the line is to be considered as the next printing start position e The initial value is not defined 31 CITIZEN CBM 290 291 User s Manual 22 Generating specified Pulse ESCp m nl n2 Code 1B h 70 h m n n2 m connector pin No See table below 0 lt nl lt 0 lt 2 lt Data is described in Hex code Signals specified by n1 n2 are output to Connector Pin m e Bit m mO means the followings S ees Drawer kick No 2 pin Drawer kick No 5 pin e time is considered as nl x 2ms and OFF time as n2 x 2ms e When m is out of the defined range n1 n2 are discarded where no signals are output Drive duty of Drawer is shown below ON time ON time OFF time 0 2 Take OFF time as being 4 times or more longer than ON time 23 Selecting Character Code Table ESC t Code 1B h 74 h n QO lt n lt 1 Datais described in Hex code Selecting Page n on the character code table e means the followings 2 Japanese Character The initial value of n is specified by Jumper setting J1 J3 32 CITIZEN CBM 290 291 User s Manual 24 Transmitting the printer status ESC v Code 1B h 76 Current printer status is transmitted e Status sent out consist
11. Specifications 1 Data transfer system Asynchronous 2 Baud rates 1200 2400 4800 9600 19200 bps Selectable by user 3 Configuration of one word Start bit 1 bit Data bit 8 bits Parity bit Add even or no parity Selectable by user Stop bit bit or more 4 Signal polarity RS 232C e Mark logic 1 3V 12 e Space logic 0 43V 12V 5 Receiving data RD signal RS 232C e Mark 1 e Space 0 7 Receiving control DTR signal RS 232C e Mark Data transfer not available e Space Data transfer available 8 Transmission control TD signal DC1 code X ON Data reception available DC3 code 13H X OFF Data reception not available 19 CBM 290 291 User s Manual CITIZEN CBM 290 291 User s Manual 7 2 Explanation of Input Output signals 7 2 1 Input Output signals 1 RD Serial receiving data signal On occurrence of framing error overrun error or parity error the data is printed as 2 DTR When this signal is READY write data or a command When they are written in BUSY overrun error is occurred and data is ignored Even during printing data can be loaded in the input buffer Further BUSY can take place on supply of power during test printing during on line or on resetting 3 TD When while in data reception the rest of input buffer on the printer side goes less than 128 bytes DC3 13H data reception impossible signals are output When the rest of inpu
12. code to be printed 0 UCA _ 2 3 JAN SEAN O NS MERE HET E ITF CODABAR NW 7 7 CODE 128 1 2 3 4 5 7 ee 75 9 EE EM ___ 35 CITIZEN GI 32 33 CBM 290 291 User s Manual e When data being held in the print buffer this command is ignored Regardless of the specified feed pitch this command feeds the paper to be required to print a bar code e When the character code Dn cannot be printed the data following after this is printed as ordinary print data e When a bar code whose number of characters to be printed is fixed has been selected e number of characters have to be always made equal to the number of characters to be printed e When the horizontal direction exceeds one line length the excess part is not printed Selecting Bar Code width GS w Code 77 H 2 ntx4 Datais described in Hex code Selecting bar code width e The initial value of this width is 3 Selecting Bar Code Height GS h n Code 1d H 68 H N lt n lt FF Data is described in Hex code Selecting bar code height e indicates the number of dots in vertical direction e The initial value of n is 162 Selecting Printing Position of HRI Characters GS H Code 1d H 48 H N Q lt n lt 3 Datais described in Hex code Selecting printing position of HRI characters in printing bar c
13. daran angeschlossenen Ger te entsprechen Keine Gegenst nde in die Geh useschlitze schieben Drucker darf nur da gewartet werden wo im Handbuch angegeben ffnen und Abnehmen von Abdeckungen die mit Do not remove gekennzeichenet sind k nnte gef hrliche spannungf hrende Stellen oder sonstige Gefahrenpunkte freilegen Die Wartung solcher Stellen darf grunds tzlich nur von besonders ausgebildetem Fachpersonal vorgenommen werden A Wenn das Stromanschlu kabel oder der Stecker besch digt oder durch gescheuert ist B Wenn Fl ssigkeit auf dem Drucker versch ttet wurde C Wenn der Drucker im Regen gestanden hat oder Wasser darauf versch ttet wurde D Wenn der Drucker trotz genauer Befolgung der Betriebsvorschriften nicht richtig arbeitet Nur die in der Bedienungsanleitung angegebenen Einstellungen vornehmen Ein Verstellen anderer Bedienungselemente k nnte den Drucker besch digen und macht umst ndliche Arbeiten eines qualifizierten Technikers erforderlich um den Drucker Wieder auf den normalen Betrieb einzustellen E Wenn der Drucker heruntergefallen ist oder das Geh use besch digt wurde F Wenn der Drucker in seiner Leistung nachl t Bitte halten Sie den Kunststoffbeutel in den die Ware verpackt ist von Kindern entfernt oder werfen Sie ihn weg damit er nicht in die Hande von Kindern ger t Das berst lpen des Beutels kann zum Ersticken f hren L rmemission kleiner 70dBA CITIZEN CBM 290 291 Us
14. error takes place The data are stored in the buffer as 2 Parity Error With an error having been detected under specifying parity check the data is stored in the buffer as 3 Overrun Error On detection of an overrun error the data are stored in the buffer as 21 CITIZEN CBM 290 291 User s Manual 7 5 Data receiving control When DTR DSR control having been selected with BUSY signal at LOW data from the host side are received With the signal at HIGH they can not be received When DTR DSR control not having been selected after X ON transmission data is received from the host side No transmission of data can take place after X OFF is transmitted 7 6 Buffering Data transfer to the input buffer include DTR signals and TD signals as the control signals concerned 1 DTR signals See 7 2 2 2 TXD signals See 7 2 3 7 7 Electrical characteristics 1 RS 232C Circuit Input RXD DSR Printer side Host side T Mark 8V Stop bit MAX 232 equivalent RXD Space 8V Start bit Output DTR TXD D gt MAX 232 equivalent 8V When busy Space Mark 8V 1 ae 8V When ready Tx Space 8V 0 22 CITIZEN 8 MAINTENANCE AND SERVICE CBM 290 291 User s Manual For the information on maintenance and service please contact our dealer or at the following address North America CBM America Corporation Service Center 363 Van Ness Way Suite 404 Torrance
15. has sufficient capacity Avoid composite wiring with a power cable or excessively extended wiring Excessive electric current may cause heat generation ignition of the supply line or shut off the power Do not step on a cable or use the equipment with excessive force tension load applied to it Never connect a grounding cable to a gas pipe There is a danger of explosion When connecting or disconnecting the grounding cable be sure to disconnect the power plug from the plug socket When disconnecting reconnecting the cables be sure to turn off the power including the mating side Connect a connector cable securely If a reverse polarity connection is made internal elements may be broken or a mating device may be adversely affected Avoid routing a signal line too long or connecting to any noisy device to protect against such effects as data deformation due to noise Use the equipment in an environment where there is a plug socket near the main body and you can easily disconnect the power plug from it to shut off the power Keep the equipment in the printing head up state when transporting the equipment or when it will not be used for a long time When transporting the equipment remove the rolled paper from it CITIZEN CBM 290 291 User s Manual PRECAUTIONS FOR HANDLING Do not handle the equipment in the following manners because problems may result Do not print without setting a roll of paper Be careful not to drop fore
16. is packed in away from children or throw it away to prevent children from putting it on Putting it on may cause suffocation to them CITIZEN CBM 290 291 User s Manual WICHTIGE SICHERHEITSANWEISUNGEN Lesen Sie die nachfolgenden Anweisungen sorgfaltig durch und bewahren Sie sie auf Befolgen Sie alle auf dem Drucker vermerkten Hinweise und Anweisungen Vor dem Reinigen grunds tzlich Stecker aus der Steckdose ziehen Keine Fl ssigkeiten oder Aerosolreiniger benutzen Nut mit einem feuchten Tuch abwischen Der Drucker darf nicht in der Nahe von Wasser aufgestellt werden Drucker nicht auf einem unstabilen Wagen Stand oder Tisch aufstellen Der Drucker k nnte herunterfallen und dabel besch digt werden Schlitze und ffnungen im Geh use in der R ckwand und im Boden dienen der Bel ftung Sie d rfen keinesfalls zugedeckt oder blockiert werden da sich der Drucker sonst berhitzt Drucker nicht auf ein Bett Sofa Teppich oder dergleichen stellen Drucker nicht in der Nahe eines Heizk rpers aufstellen Drucker darf nicht eingebaut werden falls nicht f r ausreichende Bel ftung gesorgt ist Drucker nur mit der auf dem Typschild angegebenen Spannung betreiben Wenn Sie sich nicht sicher sind fragen Sie ihren H ndler oder ihr zust ndiges Elektrizit tswerk Nichts auf das Stromanschlu kabel stellen Kabel mu so verlegt werden da man nicht darauftreten kann Ein etwaiges Verl ngerungskabel mu der Stromst rke aller
17. life of thermal print head and simple design 4 Serial RS 232C and Parallel Centronics interface are available by dip switch 5 Input buffer incorporated 6 Barcode printing by special command 7 Auto paper cutter is equipped CBM 291 only 8 User defined character registration function 94 characters 1 2 Package Make sure to confirm the following components are contained in this package Printer MAM nitesi iinne isis 1 pc Roll paper sample nigee 1 pc A cable for power supply and interface 1 pc Rack mounting bracket esses 1 pc Screw for mounting essere 2 pcs pe io P 1 pc Users manual ege ue 1 pc 1 CITIZEN CBM 290 291 User s Manual 2 BASIC SPECIFICATIONS 2 1 Model classifications CBM 290 34 Model name CBM 290 No auto paper cutter CBM 291 Auto paper cutter equipped Number of print columns 34 34 columns Font A Character set International Supplement code None Standard model 2 CITIZEN CBM 290 291 User s Manual 2 2 Specifications Number of columns Font A 34 columns Font B 46 columns Character size Font A 1 25 mm x 3 00 mm 10 x 24 2 dot space Font B 0 88 mm x 2 13 mm 7 x 17 2 dot space Character type Alphanumeric international characters Bar code type UPC A E JAN EAN 13 8 columns ITF CODE 39 CODE 128 C
18. n2 DI Dn Code 1B h 2A h m 4 nl n2 Dn mz bit image mode See the table below 0 lt nl lt FF 0 lt 2 lt 02 Data is described in Hex code According to the number of dots specified in n1 n2 specify the bit image of mode n The no of dots printed is divided by 256 whose quotient is taken as n2 and residualas nl The total no of dots printed in the bit image is equal to n1 256 x n2 When bit image data have been input in excess of dot position of one line 448 dots the excess data are discarded e dis bit image data the bits subject to printing are taken as 1 and those not as 0 bit image modes specified by m are shown as follows ff VERTICAL DIRECTION HORIZONTAL DIRECTION MODE NO OF DOTS DOT DENSITY DOT DENSITY MAX NO OF DOTS 0 8 dotsignle density 8 67DPI 101 DPI 224 208 8 dot double density 8 203 DPI 448 416 24 dot single density 203 DPI 101 DPI 224 208 24 dot double density 203 DPI 203 DPI 448 416 27 CITIZEN CBM 290 291 User s Manual e When the values set in m bit image mode are out of the above range the data following after n1 is processed as normal printing data e After completion of bit image printing printer returns to normal data processing mode 8 Dot Mode 24 Dot Mode Single Density Double Density Single Density Double Density 9 Specifying Canceling Underline ESC n Code 1B h 2D h 0
19. 0 291 User s Manual 3 Operation 3 1 Rack mounting 1 Put the main body into the rack as shown in the following drawing 2 Hold the main body from rear side with mounting bracket fasten the screws to fix the main body 3 After mounting make sure that front cover opens closes properly 4 In fasten screws do not fasten the screws until the main body is deformed This may be abnormal force onto the main body as well as be an cause of breakage 5 Thickness of rack panel to fix the main body is to be approx 1 3 mm Cautions For mounting bracket length of the screws must be 15 mm or less 7 CITIZEN CBM 290 291 User s Manual 3 2 Connecting a cable for power supply and interface 1 Make sure that main power supply is turned OFF before connecting this cable 2 Prepare power supply which satisfies the power voltage and current capacity specified in this manual 3 Firmly connect in appropriate direction the power supply and the main body using this cable As shown in the drawing this connector locates on the rear side of main body This cable integrates the cable for power supply and the cable for interface 4 Connect this cable to external power supply Pay attention not to connect power supply cable in reverse polar 5 Earth the frame of main body Earthing this is recommended to avoid noise and electronic statistic problem For connecting fix it with FG terminal on rear side properly F
20. CITIZEN CBM 290 291 User s Manual Continuous execution The Macro is executed n1 times continuously at the time intervals specified by n2 Execution by FEED SW After waiting for lapse of time specified by n2 the ERROR LED flickers and the LF switch is waited to be pressed When it is pressed the macro is executed once This action is repeated n1 times e When this command is received while in macro definition suspension of macro definition is indicated At this time the defined content is cleared e No execution takes place when macro is held undefined or n1 0 e While in macro execution with n3 1 paper feed with the LF SW is not available 39 Data Input Control ESC z n Code 1B h 3D h n 0 lt lt Data 15 described in Hex code Selecting equipment in which data input from the host is effective Fach bit of n indicates as follows an lr Invalid 1 2 3 5 Notdefined e When the printer has not been selected this printer abandons all the received data until it is selected o m ota 2 Nae IT 5 Novae 6 by this command e Even when the printer has not been selected it can become BUSY state through printer operation e The initial value of nis 1 39 CITIZEN CBM 290 291 User s Manual 40 Aligning the characters ESC a n Code 1b h 61 h n 0 lt lt 2 Datais described in Hex code All the printed data within one line a
21. CITIZEN LINE THERMAL PRINTER MODEL CBM 290 291 Japan CBM Corporation CBM 290 291 User s Manual Declaration of Conformity Manufacturer s Name Japan CBM Corporation Manufacturer s Address CBM Bldg 5 68 10 Nakano Nakano ku Tokyo 164 0001 Japan Declare the Product Product Name Line Thermal Printer Model Number s CBM 290 291 S No 00Z0001 Conform to the following Standards LVD EN60950 A3 1995 EMC EN55022 1998 Class A EN55024 1998 EN61000 4 2 1995 4 CD 8 AD EN61000 4 3 1995 3V m AM 80 1KHz EN61000 4 4 1995 1 0KV AC Mains 0 5K V Signal Lines EN61000 4 5 1995 1KV Normal mode 2KV Common mode EN61000 4 6 1996 3V 0 15MHz 80MHz AM 1KHz 80 EN61000 4 11 1994 0 5000ms 70 500ms 0 10ms Supplementary Information The product complies with the requirements of the Low Voltage Directive 73 23 EEC 93 68 EEC and the EMC Directive 89 336EEC 92 3 93 68EEC Place Tokyo Japan Signature Date November 2000 4 Full Name Mikio Moriya Position General Manager R amp D Department Europe Contact Norco Declaration AB Box 7146 S 250 07 Helsingborg Sweden Warning This is a Class A products In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures This declaration is applied only for 230V model CITIZEN CBM 290 291 User s Manual IMPORTANT SAFETY INS
22. G Terminal 8 CITIZEN CBM 290 291 User s Manual 3 3 Opening closing front cover 1 Applying your finger on the projection on the left side of the front panel pull it forward when the lock is released It opens by about 180 centering around the fixed axis 2 For closing pressing the front panel tightly close it until click sound is heard Also confirm on closing that paper is free of slack 9 CITIZEN CBM 290 291 User s Manual 3 4 Paper feeding With the LF switch pressed once paper is fed by one line Paper is fed while it is continuously pressed Do not pull paper forcibly to feed paper Use the LF switch While the front cover is open or printer mechanism is pulled down paper can be fed But do not do this often This may cause a paper jam etc 3 5 Auto paper loading function This printer equips a function to feed the paper automatically when a new paper for replacement is inserted into paper inlet of printer mechanism This printer feeds paper automatically when the printer detects the paper in paper inlet 3 6 Setting roll paper 1 25 Qu 49 Open the front cover Cut the edge of paper at a right or bent angle as the following drawing Insert the edge of paper into the paper inlet of the printer mechanism When paper is inserted into paper inlet in printer mechanism paper is loaded automatically Make sure paper winding direction After setting paper set roll paper inside of main
23. ITIZEN CBM 290 291 User s Manual 2 3 Specifications of Roll paper 2 3 1 Recommended paper Type Thermal Paper Paper width 58 0 1 mm Paper thickness 65 5 microm Outer diameter 50 mm or less Recording side Outside of roll Recommended type Japan Paper Mill TFSOKS E2C or equivalent Core 012 mm Inner diameter 18 mm Outer diameter Cautions 1 Do not paste the paper to the core 2 Chemicals or oil may change the color of paper or printed characters may fade 3 Change of paper color starts from approx 70 C Pay attention to heat humidity and sun light 4 Color of paper may be changed by being scratched by nail or hard metal etc 2 3 2 Printing position 58 mm Paper Width 3 52 mm Printing Area 3mm K 2 3 3 Position of printer head and auto cutter Paper outlet position and manual paper cut position CBM 290 Auto cutter position 291 approx 12 mm Paper faad direction Canter of print head 4 CITIZEN CBM 290 291 User s Manual 2 4 Specified Power Supply The following specifications is required for Power supply DC 5V 5 0 2 0 5 DC24V 5 2 3 A 6A or more at peak Avoid using power supply which its power capacity of power current is extremely high 2 5 Outer appearances and parts name 2 5 1 Outer appearances and parts name Manual Paper Cut Blade CBM 290 oniy
24. ODABAR 4 23 mm 1 6 inch Selectable by command Thermal Roll Paper Paper Width 58 mm Roll Diameter 050 mm or less Interface Parallel conforms to Centronics or Serial conforms to RS 232C Selectable by dip switch Input buffer 4 K bytes Paper end detection Equipped Printer stops printing when roll paper runs out completely Auto Loading function Equipped Printer automatically feeds paper when paper sensor detects paper in paper inlet International Character U S A France Germany U K Denmark 1 2 Sweden Italy Spain Japan Norway Specified by command Only CBM 291 Partial cut One tear point left and Full cut are available by command Supply voltage SV 5 Stand by Aprrox 0 2A Printing Approx 0 2A 24 V 5 Stand by Approx 10mA Printing Average 1 8 A Peak approx 6A Operating environment 40 C 35 85 RH No condensation Storage environment 20 60 C 10 90 RH No condensation Outer dimension Weight CBM 290 Approx 460g Main body only CBM 291 Approx 600g Main body only Mounting backet Approx 50g Safety standard UL CUL TUV GS EMI FCC Class A VCC I Class A These standards are applied only for the printer which is used with our exclusive AC Adapter Reliability Print head life Pulse resistance 50 million pulse printing ratio 12 5 Wear resistance 30 km at normal temperature and humidity with recommended paper Auto cutter life 300 000 cuts CBM 291 3 C
25. TRUCTIONS Read all of these instructions and save them for later reference Follow all warnings and instructions marked on the product Unplug this product from the wall outlet before cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning Do not use this product near water Do not place this product on an unstable cart stand or table The product may fall causing serious damage to the product Slots and openings on the cabinet and the back or bottom are provided for ventilation To ensure reliable operation of the product and to protect it from overheating do not block or cover these openings The openings should never be blocked by placing the product on a bed sofa rug of other similar surface This product should never be placed near or over a radiator or heat register This product should never be placed near or over a radiator or heat register This product should not be placed in a built in installation unless proper ventilation is provided This product should be operated from the type of power source indicated on the marking label If you re not sure of the type of power available consult your dealer or local power company Do not allow anything to rest on the power cord Do not locate this product where the cord will be walked on If an extension cord is used with this product make sure that the total of the ampere ratings on the products plugged into the extension cord do not exceed the extension co
26. and resulting in fire or electric shock If you find any damage problem smoke or abnormal odor sound turn off the power disconnect the power cable and contact your dealer Never repair the equipment on your own it is very dangerous Do not allow the equipment to receive a strong impact or shock such as kicking stomping hitting dropping and the like Install the equipment in a well ventilated place Do not use it in such a manner that its ventilation port will be blocked Do not install the equipment in a place like a laboratory where chemical reactions are expected or in a place where salt or gases are contained in the air Use only power of the specified voltage and current capacity Do not connect disconnect a power cord or a data cable while holding the cable Do not pull install use or carry the equipment in such a manner that force will be applied to the cables Do not drop or insert any foreign substances such as clips or pins into the equipment Do not put many loads on one electrical outlet Do not spill any liquid or spray any chemical containing liquid over the equipment If any liquid is spilled on it turn off the power disconnect the power cable and power cord from the plug socket and so on and contact our dealer Do not disassemble or remodel the equipment Negligence of this may cause fire or electric shock An equipment packing bag must be discarded or kept away from children A child can suffocate if
27. being in MARK state e it keeps waiting until receptible state is created 33 CITIZEN CBM 290 291 User s Manual VALUE FUNCTION MEE INNO DEN EPI Not defined p T y Not defined Paper end Paper out Not defined 066081 Not used Not defined Not defined NENNT Not defined Remarks This command is valid only for serial interface mode 26 Specifying Canceling Inverted Characters ESC Code 1B h 7B h n 0 lt n lt FF Data is described in Hex code Specifying canceling inverted characters e n is valid only for the lowest bit nO e Bit n n0 means the followings 4 Canceling inverted characters Specifying inverted characters e Inverted printing means printing the line at 180 turned This is valid only when this is specified at the beginning of a line e The initial value of n is 0 27 Specifying Canceling 90 right turned Characters ESC V n Code 1B h 56 h n O0 lt n lt 1 Datais described in Hex code Specifying canceling characters 90 right turned character e No underlines are attached to 90 right turned characters e means the followings Canceling 90 right turned Characters Specifying 90 right turned Characters e The initial value of n is 0 34 CITIZEN Q8 Q9 30 CBM 290 291 User s Manual Specifying Absolute Positions ESC nl m Code 1B h 24 h nl n2 OSnl lt O lt n2 lt 1
28. er s Manual IMPORTANT This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 off FCC Rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference CAUTION Use shielded cable for this equipment Sicherheitshinweis Die Steckdose zum Anschlu dieses Druckers mu nahe dem Grit angebracht und leicht zug nglich sein For Uses in Canada This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian department of communications Pour L utilisateurs Canadiens Cet appareil num rique ne d passe pas les limites de car gorie a pour les missions de bruit radio manant d appareils num riques tel que pr vu dans les r glements sur l interf rence radio du d partment Canadien des communications CITIZEN S io rap CBM 290 291 User s Manual lt CAUTIONS gt Prior to using the equipment be su
29. fied Power Supply 2 222222 e e Dee eee mde e e e es 4 2 4 Specified Power Supply tete eoe ete Inka 5 2 5 Outer appearances and parts NAME seision iioii erae i aeniea en on 5 2 5 1 Outer appearances and parts name iiec ne Dae Rr IRR 5 25 2 Explanation of each parts Ui Ub I Ur eO eet e e dert e Wace er peret tp 6 gt trate A tenue IUe een ue eU DU E den re 7 3 1 Rack mounting REI tadousssduseusd ERU RUE 7 3 2 Connecting a cable for power supply and 8 3 3 Opening cl sing front COVER een Hem e Hte Hee mh ere dene AIO eee E e nit 9 4 erts 10 35 zu tee ae RB 10 3 6 Setting roll paper ota ete mt ach t pre dee redo hada cod Beben in tro e eich 10 3 7 Removing paper jam and canceling cutter 10 12 5 8 Self print functions roe eg eeu epe au ea eat e eadem 13 3 9 PE and Mechanical alarm ton t tn ed ki Rs 13 2 92 Paper end PB nie oer Oi Ob dps oe 13 3 92 0 en ede ose 13 4 Dip switch
30. ign substances such as clips pins and screws into the main body Do not spill any liquid or spray any chemical containing liquid over the equipment Do not stamp on drop hit or give a strong shock to the equipment Never use a pointed object such as a pen to operate the operation panel Do not use Scotch tape to fasten paper together for continuous use With the printing head down never rotate the paper feed knob or force to pull the set roll of paper by hand To Prevent Injury and Spreading of Damage Do not touch the printing part of the print head When turning on the power do not touch the moving parts such as a cutter and gear inside the main body or electric parts Be careful to avoid bodily injure or damaging other objects with an edge of sheet metal Should any error occur while operating the equipment stop it immediately and disconnect the power plug from the plug socket Should a problem occur leave solving it to our serviceman Do not disassemble the equipment on your own When opening closing the panel and so on be careful not to catch your hand or finger on the equipment CITIZEN CBM 290 291 User s Manual IN A caution label has been pasted to the position shown in the figure below Read the precautions for handling thoroughly to operate the equipment correctly This label alerts you to the danger that touching the printing head or motor can cause a burn injury because they are h
31. it data Positive signal Signal to reset control board 8 bit data request signal Pulse signal output at the end of the BUSY signal Negative logic Signal to indicate BUSY state of the printer Input new data for LOW Positive logic Signal which is made LOW when printer is in alarm state Negative logic Signal which is output when paper runs out Positive logic 16 CITIZEN CBM 290 291 User s Manual 6 3 Electrical characteristics 1 Input Signal Level All the input signals are at TTL level HIGH level 0 7Vcc MIN LOW level 0 3Vcc MAX 2 Output Signal Level All the input signals are at TTL level HIGH level 0 1 V MIN LOW level 0 1 MAX 3 Conditions Input signal of STB and RESET are pulled up by 3 3K Ohm Others are pulled up by 50K Ohm Printer side Host side All the output signals are pulled up by 50K Ohm 17 CITIZEN CBM 290 291 User s Manual 6 4 Timing chart Tl T4 T5 T6 1 Data Input and Printing Timing S ue BUSY ACK ACK is not outputted T2 T3 0 5 micro sec MIN 270 ns MAX 2 3 micro sec TYP 500 ms MIN On supplying power 6 5 Data receiving control When BUSY signal is LOW data from the host can be received When it being HIGH data can not be received 6 6 Buffering 4 K bytes input buffer is incorporated Due to this large buffer host side is released immediately 18 CITIZEN 7 Serial Interface 7 1
32. l print buffer however no printing is performed Printing and Paper Feed Command LF Code 0A h Prints data inside the input buffer and feeds lines based on the line feed amount having been set Setting the right space amount of the characters ESC SP n Code 1B h 20 h n 0 nx 20 Data is described in Hex code The rightward space amount is set in dot unit 1 203 inch unit In the initial value it is n 0 The rightward space amount in double wide mode is made double of the set volume Collective Specifying Printing Mode ESC n Code 1B h 21 h 0 lt n lt FF Data is described in Hex code Printing mode is assigned Each n bit indicates the following sr FUNCTION 9 i 0 haer Fm je Former 6 Undefined 25 CITIZEN CBM 290 291 User s Manual With double height and double width being specified simultaneously double wide and double high characters are consisted An underline is attached to the full character width which however is not attached to the part having been skipped by the horizontal tab Neither is it attached to 90 right turned characters The underline width is as having been specified by lt ESC gt The default setting is 1 dot width In case that double wide character and normal character exist in same one line the layout of underline is consistent one 6 Specifying Canceling Download Character Set ESC n
33. lades to home position and carries out initializing cutter lock was cleared completely In case cutter does not return to home position or occurs some error again turn OFF power turn the knob which locates on left bottom side of auto cutter to the front side as shown in the below then return cutter blade manually and remove the paper inside of auto cutter 5 After fixing the problem pull down head up lever and return printer mechanism to its home position Cautions Since print head and motor are hot do not carry out this action right after printing This may cause burning from this heat For removing the remaining paper do not touch the surface of print head and motor 12 CITIZEN CBM 290 291 User s Manual 3 8 Self print function By supplying power as pushing FEED switch or send RESET signal to this printer type of characters which is used ROM version and DIP switch setting etc are automatically printed For CBM 291 paper is automatically cut off after this self printing 3 9 PE and Mechanical alarm 3 9 1 Paper end PE This sensor detects the existence of paper Printer stops printing when roll paper runs out outputs BUSY and PE signal and lights up PAPER lamp When new roll paper is set this signal is canceled and PAPER lamp lights off And then printer starts printing and becomes data waiting status When any print data is remaining in print buffer make sure that printer starts printing the data after new roll pa
34. lt n lt 02 data is described in Hex code Specifying canceling an underline An underline is attached to the full character width Itis however not attached to the part e having been skipped by horizontal tab command e Anunderline is not attached to a 90 right turned characters e Types of underlines by n value are shown below a Canceling an underline Specifying an underline for 1 dot width 2 Specifying an underline for 2 dot width 10 Specifying 1 6 inch line feed rate ESC 2 Code 1B h 32 h The line feed rate per line is specified by 1 6 inch 11 Setting line feed rate of minimum pitch ESC 3 n Code 1B h 33 h n 0 n lt FF data is described in Hex code The line feed rate per line is specified by n 360 inch The initial value is n 60 1 6 inch 18H being 4 23 mm line feed rate 28 CITIZEN 12 13 14 CBM 290 291 User s Manual Initializing Printer ESC Code 1B h 40 h Clears data stored in the print buffer and brings various settings to the initial state Default state e Data inside the internal input buffer are not cleared e Dip switches setting are read once again Setting Horizontal Tab Position ESC D n NUL Code 1B h 44 h n 00 h 0 lt lt Data is described in Hex code Specifying a horizontal tab position e n indicates the no of columns from the beginning to the horizontal tab position At this time n set position
35. mesready for print 13 CITIZEN CBM 290 291 User s Manual 4 Dip switch setting Dip switch locates on the rear side of main body Make sure that power is turned OFF before changing Dip switch settings Change during power is ON can not be effective DIP SWITCH OFF FACTORY SETTING DS1 1 AUTO CUTTER EQUIPPED NONE OFF CBM 290 ON CBM 291 LF ENABLE STANDARD XON XOFF SEE BELOW 8 7 6 5 INPUTMETHOD PARITY BAUDRATE OFF OFF ON 1200 bps J QN ON A 4800 bps vu QFE OFF 9600 bps L OFP ON 19200 bps ON ORE SON p ON 2400 bps LLOEP OFF 4800 bps ON OFF 19200 bps ON ON 1200 bps OFF 2400 bps sum QFE 4800 bps ON OFF 9600 bps ON 19200 bps Remarks For CBM 290 It make Error when ON is selected for DS1 1 DS 1 4 is ignored when parallel input is specified Some specifications has been selected in factory setting by jumper as follows International model Short International model Short International character U S A Short Auto loading Enabled Short Input Buffer 4 K bytes Short Serial communication bit length 8 bit Short Short Open 14 CITIZEN CBM 290 291 User s Manual 5 Connecting connector Configuration of the connector for power and interface which is packed in this box is as follows Make sure to confirm the following configuration before connecting the co
36. n 14 5 Connecting COMMECCON 4 c eee be 15 5 d Function of each connector plns Eee tte d erede rites 15 5 2 PRECAUTIONS ie ree RU E Ret t teh e hb IC d det itt sl de t ee babe etes 16 6 Parallel Interface 16 61 Jette ter tete ee idee eot Diet delta fen dele reet Ein dee rien 16 CITIZEN CBM 290 291 User s Manual 6 2 Explanation of input output signals eese trennen treten 16 6 3 Electrical charactensucs sin Sigo en enden ea denen 17 64 Timing Chart wrasse EIS 18 6 5 Data receiving Control 2 ee eer e er eget ree Por er ee nennen 18 6 6 Buffeting ns te eite e erri rrr a pet rere e Het Cen m Husa Lee He veterea 18 7 Serial Interface seseesesossesnenesssnesesnsnennenennsnenennsnennenennsnensnnsnennsnennenensnnsnennsnennsnenssnsnesnsnennsnennsnssssnsnesnsnesnenesssnssennnenne 19 TA Specifications ns ee ege o Neem dt Balls ee Bin d 19 7 2 Explanation of Input Output signals eese enne nnne enne nnns 20 72 1 Input Output Signals iier RD RE ERU E Nh EH on ing 20 7 3 Date COMMS ULATION os s inre tp dem eer 21 V A Brror detectoDs Odette tet edita mets eee ee ene 21 7 5 Data receiving control fer ives te eio rin no
37. nnector 5 1 Function of each connector pins PIN NO SIGNAL NAME FUNCTION OUTPUT POWER SUPPLY FOR CIRCUIT 5V INTERFACE DTR SERIAL INTERFACE TXD SERIAL INTERFACE RXD SERIAL INTERFACE DSR PARALLEL INTERFACE RESET Not available LY20 40P DT1 P5 JAE or equivalent Applicable connector LY10 DC40 JAE or equivalent Using connector 15 CITIZEN 5 2 Precautions CBM 290 291 User s Manual For LED ERROR there is a resister of 330 Ohm on the circuit side to make current value 10 mA Please use LED which its voltage is approx 2V LED over 10 mA may break a control board Make sure to supply power to all pins of power supply for circuit and power supply for operation to keep required current capacity Serial interface equips a driver and receiver of RS 232C make sure to use it at RS 232C level RESET terminal is pulled up by 3 3K Ohm Make sue to make this terminal NC when this terminal is not used Absolutely do not carry use No 19 No 21 and No 40 pins Since they are used for printer main unit In case they are used they may cause abnormality or break control board 6 Parallel Interface 6 1 Specifications Data input method 8 bit parallel signal DATAO 7 Control signals ACK BUSY STB FAULT PE RESET 6 2 Explanation of input output signals DATAO 7 8 bit parallel signal Positive logic STB RESET ACK BUSY FAULT PE Strobe signal to read 8 b
38. odes e means the followings No printing Above the bar code Below the bar code Both above and below the bar code The initial value of n is 36 CITIZEN CBM 290 291 User s Manual 34 Selecting the font of HRI code GS f n 35 Code 66 h N nz0 l Selecting the font of HRI code in printing bar code The type of font can be printed by selecting n is as follows Defining Download Bit Image 65 nl n2 Dn Code 1D h 2A h nl n2 Dn 1 lt nl lt FF 1 lt n2 lt 48 nl X n2 lt 1311 Data is described in Hex code Defines downloading bit images of the number of dots specified by n1 n2 e The numbers of dots are nl x 8 in horizontal direction and n2 x 8 in vertical direction Dn indicates bit image data e The download bit image thus defined remains effective until redefinition ESC execution ESC amp or power OFF takes place e download character and a download bit image cannot be defined simultaneously With this command executed defined content of a download character is cleared Relations between the bit image data and the dot defined are shown below 37 CITIZEN CBM 290 291 User s Manual 36 Printing Download Bit Image 65 m Code 1D h 2F h m 0 lt lt 3 Data is described in Hex code Prints download bit iamges in a mode specified by m e Modes be selected by m are shown in table for selection with m are shown below
39. ot CITIZEN CBM 290 291 User s Manual G ORDINARY MAINTENANCE Make sure to maintain the equipment afterswiching OFF the power When cleaning the platen of printer mechanism wipe out the dirty portion by a cotton pud dipped into ethyl alcohol When cleaning the surface of the main unit case use soft cloth In case the dirty portion can not be cleared out by the soft cloth use wet cloth squeezed thghtly Absolutely do not use thinners trichlene benzine or ketone group solvents or chemical impregnated cleaning cloths In case the point head becomes dirty because of paper dust clean it by using a soft brush CAUTION Do not carry out the maintenance right after printing since print head and moter are so hot CITIZEN CBM 290 291 User s Manual CONTENTS UU A 1 td antea 1 1 2 PACka Seis EI 1 2 BASIC SPECIFICATIONS 2ur200020020000n00200e0ne0neneneenennennensenennesnennensnnennesnennenennennennsnssnesnesnssnenssnesnesnensenesnesnssnennen 2 DZ AModel classifications MEC m 2 pA PEC Ati ONS E 3 2 3 Specifications ob Roll Paper s er REPRE rede red te edet es 4 2 3 1 Recommended paper cone ode be ee et Hagener 4 2 3 2 Printing POS OM s eerie ee eet ett cio e tei ete e de sedet die etii 4 2 3 3 Position of printer head and auto cutter eene nnne nennen rene enne tnnt tenete 4 2A Speci
40. per is set 3 9 2 Mechanical alarm This printer stops printing stops supplying motor and print head with power and outputs BUSY signal and FAULT in Parallel interface signal to host computer when the motor of printer mechanism is locked auto paper cutter is locked or temperature of print head is getting high In this case turn OFF power supply and clear the problem To make printer stand by mode turn ON power supply after clearing the problem Make sure that the data which is stored in the buffer is to be cleared due to power supply is turned OFF Absolutely do not carry out clearing the problem during power is ON Auto paper cutter lock paper jam Turn OFF power supply and clear the problem To make printer ready for print turn ON power again after clearing the problem In this case the print data which is remaining inside of print buffer is cleared due to power supply is turned OFF Absolutely do not carry out clearing problem supplying power Head up condition Pull down had up lever forward Print head is pulled down and error signal is cleared then printer becomes ready for print e Heating up of print head temperature When temperature of print head is getting high due to continuous printing etc printer stops printing During temperature of print head is high any operation is not available keep printer without printing As soon as temperature of print head goes low error signal is canceled automatically and printer beco
41. rd ampere rating Also make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock Never spill liquid of any kind on the product Except as explained elsewhere in this manual don t attempt to service this product by yourself Opening and removing those covers that are marked Do Not Remove may expose you to dangerous voltage points or other risks Refer all servicing on those compartments to service personnel Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions A When the power cord or plug is damaged or frayed B If liquid has been spilled into the product C If the product has been exposed to rain or water D If the product does not operate normally when the operating instructions are followed Adjust only those controls that are covered be the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation E If the product has been dropped or the cabinet has been damaged If the product exhibits a distinct change in performance indicating a need for service Please keep the poly bag which this equipment
42. re aligned in the specified position Depending on n value positional alignment is carried out as in the table below POSITION a Left end alignment Centering Right end alignment This is valid only when n is inputted at the beginning of line The initial value of n is 0 41 FullCut ESC i Code 1B h 69 h Activating auto cutter Full cut This is valid only when n is inputted at the beginning of line Make sure to feed the paper by 18 mm or more before cutting paper unless characters remain before the cutting point 4 CUT POSITION PAPER FEED DIRECTION AAAAA CUT POSITION Print Result Cutting Condition 40 CITIZEN CBM 290 291 User s Manual 42 Partial Cut ESC m In selection of cutter option Code 1B h 6D h Activating auto cutter unit Partial cut e Thisis valid only when n is inputted at the beginning of line sure to feed the paper by 18 mm or more before cutting paper unless characters remain before the cutting point AAAAA CUT POSITION PAPER FEED DIRECTION 4 CUT POSITION AAAAA Print Result Cutting Condition 41 CITIZEN CBM 290 291 User s Manual Character Table 10 1 International 10 CITIZEN 54 CBM 290 291 User s Manual 10 2 International Character Code Table 8 9 U S Land France Germany U K Denmark I Sweden Italy Spain Japan 2
43. re to read this User s Manual thoroughly Please keep it handy for reference whenever it may be needed The information contained herein may be changed without prior notice Reproduction of part or all of this User s Manual without permission is strictly prohibited Never service disassemble or repair parts that are not mentioned in this User s Manual Note that we will not be responsible for damages attributable to a user s incorrect operation handling or an improper operating environment Operate the equipment only as described in this User s Manual otherwise accidents or problems may result Data are basically temporary they cannot be stored or saved permanently or for a long time Please note that we will not be responsible for damages or losses of profit resulting from losses of the data attributable to accidents repairs tests and so on If you have any questions or notice any clerical errors or omissions regarding the information in this manual please contact our office Please note that notwithstanding Item 8 above we will not be responsible for any effects resulting from operation of the equipment This is an illustration mark used to alert your attention Gi This is an illustration mark used to indicate such information as an instruction or the like CITIZEN CBM 290 291 User s Manual N WARNING Never handle the equipment in the following manners as it may break become out of order or overheat causing smoke
44. s of 1 byte whose content is as in the table below In DTR DSR control after receptible state of the host DSR signal being in SPACE state is confirmed only 1 byte is transmitted In XON XOFF control DSR signal state not being confirmed only 1 byte is transmitted In DTR DSR control when the host is in unreceptible state DSR signal being in MARK state it waits until receptible state is created n paper end paper near end status this command may be unreceptible state due to BUSY state e Remarks This command is valid only for serial interface model VALUE FUNCTION L Not defined a eee Notdefined With paper Without paper Netde ined N N Not defined N N Not defined 25 Transmitting the status of Peripheral Equipment ESC u Code 1B h 75 h n 0 Current status of connector pin No 3 is transmitted e means the followings Drawer Kick Connector No 3 e Status transmitted consists of 1 byte whose content is as in the table below Any equipment has not been connected to this connector Bit 0 of n is always 1 In DTR DSR control after receptible state of the host DSR signal being in SPACE state 15 e confirmed only 1 byte is transmitted Further in XON XOFF control DSR signal state e not being confirmed only 1 byte is transmitted In DTR DSR control when the host is unreceptible state DSR signal
45. t buffer goes more than 256 bytes DC1 11H data reception possible signals are output to the host When DTR DSR control having been selected in status information transmission it is first confirmed that DSR is space and data is sent When DTR DSR control has not been selected DSR is ignored and data is transmitted 4 FG Case GND 5 GND Common GND on the circuit 20 CITIZEN CBM 290 291 User s Manual 7 3 Date configuration MARK SPACE 1 Start bit 2 Data bit 4 parity bit 3 Stop bit 1 or more 1 Start Bit In 1 2 bit from the mark to space starting edge state is read once again When space state is confirmed it is recognized as the start bit If it is mark state it is not taken as the start bit Without taking it as an error detection of a start bit is carried out once again 2 Data Bit 4 Parity Bit Data bit and parity bit are sampled at 1 2 start bit for time length equal to 1 bit The state thus sampled is taken as the data for the bit concerned Bits are named as Bit 0 Bit 1 parity bit counted from the one close to the start bit 3 Stop Bit The stop bit is a mark level of 1 bit or more With space having been detected on detection of a stop bit framing error takes place 7 4 Error detection Parity framing and overrun are detected On detection of any error the data are stored in the buffer as 1 Framing Error With space state having been detected on detection of a stop bit
46. the bag is placed over the head CITIZEN CBM 290 291 User s Manual N PRECAUTIONS FOR INSTALLATION Do not use or store the equipment in a place exposed to fire moisture or direct sunlight or in a place near a heater or a thermal device where the prescribed operating temperature and humidity are not met or in a place exposed to much oil iron powder or dust The equipment may become out of order emit smoke or catch fire Do not install the equipment in a place like a laboratory where chemical reactions are expected or in a place where salt or gases are contained in the air There is a danger of fire or electric shock Firmly secure the equipment onto a flat and stable mounting panel free from vibrations and angled at 0 to 90 in a well ventilated place Do not install or use the equipment in a place where its operation could be hindered Do not place anything on the equipment as it can lead to problems Use accessory fittings and screws to secure the equipment Tighten the screws firmly and properly Excessive tightening can result in problems or damage Do not use the equipment near a radio or TV receiver Do not share the power from a plug socket a radio or TV receiver is connected to It may cause a reception problem Use only power of the specified voltage and current capacity Be careful not to mistake polarity The equipment may become out of order emit smoke or catch fire Confirm that a plug socket used for connection
47. unit Eliminating slack on the printing paper and close the front panel Feed paper by pressing Feed switch if necessary Factory setting is Head up position Make sure to pull head up lever forward to pull down printer mechanism Because auto paper feed can not be carried out at had up condition When any print data is remaining us print buffer printer stars printing automatically after loading paper 10 CITIZEN CBM 290 291 User s Manual Make sure to pay attention to the followings l In case that the paper is bent or the paper is not fed properly set print head at head up condition and remove the paper carefully by turning paper feed knob 2 For replacing roll paper set print head at head up condition and remove the paper which remains in printer unit carefully by turning paper feed knob Good Good No Good No Good No Good No Good PEE LIS ET PTE 11 CITIZEN CBM 290 291 User s Manual 3 7 Removing paper jam and canceling cutter lock Remove paper jam or cancel cutter lock by following the procedure explained below 1 Open front cover 2 Put mechanism lock lever inside of main body pull down printer mechanism When paper remains inside of printer remove this paper 3 Removing paper jam Remove paper jam manually with care To pull out the paper from printer mechanism pull it out carefully at head up condition 4 Canceling cutter lock Remove paper inside of paper cutter and turn ON power In case cutter b
Download Pdf Manuals
Related Search