BlockBuster 6
Contents
1. WWW PROLIGHT CO U UK BLOCKBUSTER 6 ORDER CODE LEDJ73 LEDJ BlockBuster 6 WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION Keep this equipment away from rain moisture and liquids SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty LEDJ BlockBuster 6 Safety IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution e Never remove warning or informative labels from the equipment e Do not open the equipment and do not mod2. 1 100 FS Flash speed from value 00 100 2 Auto run Runs 14 programmes in a continuous loop the frequency means the speed of the run times can be set via the UP and DOWN buttons 3 DMX mode You can control the units individually using your DMX controller a The control board allows you to assign the DMX address which is defined as the first channel from which the BlockBuster 6 will respond from the controller For address setting press the set up button until the display shows as follows LEDJ BlockBuster 6 Operations b DMX protocol The control board allows you to set 5 8 11 or 20 DMX channels for different applications Press the set up button until the display is as follows Set the desired channels 5 8 11 or 20 Via the UP and DOWN buttons 1 Set for 20 Channels The dimmer occupies the first channel when DMX value is smaller than 251 the flash occupies the second channel each spot occupies 3 channels six spots occupy 18 channels and the full unit occupies 20 channels 2 Set for 11 channels The dimmer occupies the first channel when the DMX value is smaller than 251 the flash occupies the second channel every 2 spots occupy 3 channels six spots occupy 9 channels and the full unit occupies 11 channels 3 Set for 8 channels The dimmer occupies the first channel when the DMX value is smaller than 251 the flash occupies the second channel every 3 spots occupy 3 channels six spots occu
3. ify the equipment e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the System life Only use the equipment indoors Do not expose to flammable sources liquids or gases Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable e Make sure that the available voltage is between 220v 240v Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again If the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service Only use fuses of same type and rating Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS WARRANTY One year from date of p
4. py 6 channels and the full unit occupies 8 channels 4 Set set 5 channels The dimmer occupies the first channel when the DMX value is smaller than 251 the flash occupies the second channel six spots occupy the same 3 channels and the full unit occupies 5 channels 5 During any of the four above DMX modes the first DMX channel value must be between 251 and 255 LEDJ BlockBuster 6 DMX Protocol DMX Protocol 0 10 BLACKOUT Glai m 3 2232 yvettow worusgp 0225 0 2882 BLUE 8 7287 wie 9 8898 SLOWDREAM _ 251 255 FLOW 1 FLASH 14 143 153 FLOW 2 SPEED 0 225 NOT USED 209 219 2 COLOUR FLOW 1 SPEED 9255 COLOUR 0 22 220 230 2 COLOUR FLOW2 gt gt 0 28HZ 24 gt SENSITIVITY 22 231 255 SOUND ACTIVE 0 255 NOT USED NOT USED 32 grade 4 Slave mode Press the MODE button repeatedly until the display shows Slave Mode The unit will now follow another that is set to Master Mode 5 Sound mode Adjust the audio level input by pressing the UP and DOWN buttons The range is 0 31 LEDJ BlockBuster 6 Specifications Specifications e 324 high intensity LED s e Red 108 Green 108 Blue 108 total 324 e LED beam angle 30 5 e Dimensions 800 x 100 x 75mm e Weight 5 5kg e Power in 240v 50Hz e Power consumption 35 watts
5. urchase OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns electric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property LEDJ BlockBuster 6 Operations Operation When the power is turned on the LCD display will be as below ne SECOND Press the MODE button to activate the main menu Built in programme Auto run DMX mode Slave mode and Sound mode Built in programme Runs one of the 14 built in programmes Auto run Runs the built in programmes one after another in a continuous loop DMX mode Control by external DMX controller Slave mode The unit in this mode can be linked to run with another unit set to Master mode Sound mode Programmes are activated to the sound by the built in microphone 1 A programme is a sequence of different steps with the BlockBuster 6 you can select up to 14 different programmes Press the set up and the UP DOWN buttons to select between pro grammes 00 14 and select the desired programme value step time and flash For example Press the set up button to move the cursor to select 02 and then desired Sp step time or Fs flash speed e SP Step time value from 00
Download Pdf Manuals
Related Search