Ferm Angle Grinder FAG-115N
Contents
1. Watch what you are doing Use common sense Do not operate tools when tired or after taking alcohol or pre scription non prescription drugs Ferm EXPLODED VIEW Ferm SPARE PARTS LIST FAG I 15N REF NR DESCRIPTION FERM NR 6 PINION GEAR 406058 E ARMATURE 406059 18 SIDE HANDLE 406274 23 SPINDLE GEAR 406066 3 PROTECTING COVER 406718 33 FLANGEINSIDE 406846 35 FLANGE OUTSIDE 406847 37 STATOR 406060 39 CARBON BRUSH 40606 40 CARBON BRUSH HOLDER 406062 43 SWITCH 406063 45 SLIDE SWITCH KNOB 406064 48 SWITCH DRAW BAR 406065 55 WRENCH 406814 Ferm OPERATIONAL SAFETY Warning Never use the machine for grinding mag nesium workpieces Use fibre reinforced discs only Do not use near flammable materials or people Do not use the machine to grind cut deeper than the maxi mum grinding depth of the disc Do not use grinding discs for deburring Concentrate Routine and repetition can lead to mistakes Remember that a slight lack of concentration can result in serious injuries ina split second Keep work area clean Cluttered areas and benches invite injuries Consider the work environment Do not expose power tools to rain or use them in damp or wet locations Keep work area well lit Do not use power tools in the pre sence of flammable liquids vapours or gases Guard against electric shock This unit contains dangerous voltages Use a RCD resi dual current device to provi2. 12 and cannot touch the grinding sur face Inspect the grinding disc for any damage do not use cracked ripped or otherwise damaged discs Setthe guard rotate the guard to the best position to catch sparks and debris from the disc Run idle for 30 seconds if there is any abnormal vib ration or other fault switch off inspect and rectify before continuing OPERATION Check the switch is in OFF position Pluginto a suitable mains supply and switch on To switch ON slide the switch forwards to the I position Toswitch OFF press the switch which will jump to the position O DURING USE Do not put the machine down with the motor still running Keep your finger off the spindle lock button it must not be pressed while the machine is running Do not put the machine down on a dusty surface dust will get into the air vents and damage the motor Regularly inspect the disc during use for signs of damage or wear and replace when required Switch the machine off before removing the plug from the mains socket MAINTENCE CARE AND REPAIR AN Ensure the grinder is unplugged from the mains Switch off and unplug the machine before carrying out any cleaning or maintenance work CLEANING Do not use flammable liquids to clean the angle grinder FAULTS Switch OFF immediately at the mains plug and remove the plug when The plug or cable is damaged The switch on the machine is defectiv
3. TEE The guarantee conditions can be found on the separately enclosed guarantee card CE DECLARATIONOFCONFORMITY UK We declare under our sole responsibility that this productis in conformity with the following standards or standardized documents EN 501 44 1 prEN50 1 44 2 3 EN 55014 1 EN 550 14 2 EN6 1000 3 2 EN6 1000 3 3 in accordance with the regulations 98 37 IEEC 73 23 EEC 89 336 EEC from 01 12 2001 GENEMUIDEN NL W Kamphof Quality department
4. UK Subjectto change USER S MANUAL Document Ref FAG 115N 17899 PMR4 issue Mar 02 Copyright These instructions are the sole property of Ferm Omega Tools and may not be reproduced Ferm Angle Grinder FAG II5N Ferm aaa Screwfixart nr 17899 Ferm B V P O Box 134 8280 AC Genemuiden NL www ferm com 0210 23 CURYEnglish AY FERM FAG II5N ANGLE GRINDER I I5 MM USERS MANUAL TECHNICALSPECIFICATIONS Voltage Frequency Power input No load speed 11000 min Disc diameter 115mm Spindle dimension M14 Weight 2 2kg Lpa sound pressure 89 6 dB A Lwa acoustic power 102 6 dB A Vibration value 1 9 m s2 PACKAGE CONTENTS The package contains Angle grinder Side handle Spanner Set carbon brushes Instruction manual Guarantee card Check the machine loose parts and accessories for transport damage PRODUCT INFORMATION 1 On off switch 2 Guard 3 Side handle 4 Grinding disc 5 Spindle lock SAFETY INSTRUCTIONS The following pictogram is used in these instructions for use AN Denotes risk of personal injury loss of life or damage to the tool in case of non observance of the instructions in this manual Carefully read this manual before using the machine Make sure that you know how the machine functions and how to operate it Maintain the machine in accordance with the instructions to make sure it functions properly Keep this manual and th
5. de protection against elec trical shock Prevent body contact with grounded sur faces e g pipes radiator ranges or refrigerators Keep children and pets away Do not let children or pets come into contact with the tool extension cable or work area Do not force the tool It will work better and safer at the rate for which it was intended Use the right tool Do not force small tools or attachments to do the job ofa heavy duty tool Do not use tools for purposes for which they were not intended for example do not use a circular saw for cutting trees or logs Do not abuse cable Never carry the tool by the cable or pull it to disconnect it from the power socket Keep the cable away from heat oil and sharp edges Do not touch the metal plug pins when connecting or removing the plug Secure Work Use clamps or a vice to hold work It is safer than using your hand and it frees both hands to operate the tool Do not over reach Keep a proper footing and balance atall times Disconnect tools from power supply When not in use before servicing and when changing accessories suchas blades bits and cutters AN Always switch off and unplug the angle grinder from the power supply before making adjustments or changing grinding discs Remove adjusting keys and wrenches Ensure that they are removed from the tool before swit chingon Ferm Avoid unintentional starting Do not carry plugged in tools with your finger on the switch Ch
6. e You smell or see smoke caused by scorched insula tion in the machine Ferm Overheating The ventilation slots are blocked with dirt Clean with dry cloth The machine does not start when switched on Check the mains lead and the fuse plug Take to your Ferm Dealer for repair The motor is defective Take to your Ferm Dealer MAINTAIN TOOLS WITH CARE Keep the tool clean for better and safer performance Store the discs properly in accordance with the maker s instructions Follow instructions for changing accessories Inspect tool and extension cables periodically and if damaged have them repaired by a qualified person or authorised service body Keep handles free from oil or grease Keep the ventilation slots clean to prevent motor overheating Check for damaged parts Do not use a tool with damaged parts before further use a damaged tool must be carefully checked by a qualified person to determine that it will operate properly Check for alignment of moving parts binding or breakage of parts mounting and other conditions that may affect its operation A damaged part or guard should be properly repaired by an authorised service centre unless indica ted otherwise in the instruction manual Have defective switches replaced by an authorised service centre Do not use a tool if the switch does not turn on and off Have your tool repaired by an expert This appliance is manufactured in accordance with rele vant saf
7. e enclosed documentation with the machine Ferm products are manufactured to high quality stan dards they are safe and fit for purpose at time of sale but all tools can be dangerous if the correct precautions are not taken Always follow these instructions do not carry out the operation until you are sure you can do so in saf ety Remember to consider the work environment for safe operation as well as safety for tool use Warning When using electric tools basic safety precautions should always be followed to reduce the risk of fire electric shock and personal injury Read all these instructions before attempting to operate this product Save these instructions for future reference PERSONAL SAFETY Use Personal Protection Safety Equipment Protect eyes with safety glasses or goggles note the use of safety protective eyewear without the CE mark can lead to serious injury if the lens breaks A suitable dust mask should be worn if cutting drilling or sanding is dusty in particular chipboard or MDF Approved safety footwear and headgear should worn as appropriate for example on building works or when heavy weights are involved Wear suitable gloves and apron to protect against sparks debris Wear earplugs or ear defenders Dress properly Do not wear loose clothing or jewellery It can get caught in moving parts Non skid footwear is recommended when working out doors Wear protective hair covering to contain long hair Stay alert
8. eck that the switch is off before plugging in to socket Extension cables Use only three core earthed extension cables suitable for the power input of the tool minimum cable size 5mm2 Plug into an earthed socket only When using a cable reel unwind it fully Do not use long extension cables Outdoors use If the tool is suitable to be used outdoors only use an extension cable intended for outdoor use and marked accordingly Usea RCD residual current device to pro vide protection against electrical shock Do not use in rain or damp conditions Connecta dust extraction device Whenever there are facilities for fitting a dust of fume extraction system make sure it is connected and used Use recommended accessories The use of any other accessory or attachment other than recommended in the instructions or catalogue may pre senta risk of personal injury Use extension cables suita ble for the power input of the grinder minimum cable size 5mm2 When using a cable reel unwind it fully ASSEMBLING THE ACCESSORIES AN Ensure the grinder is unplugged from mains TO MOUNT THE GUARD Remove the flange nut anticlockwise and pull the flange from the spindle 5 Unscrew the 4 screws washers 3 and 4 and remove the guard mounting washer 2 Put the guard I on the machine raised edge up and secure with the guard mounting washer and screws washers Tighten the screws firmly Putthe flange and flange nut back on the sp
9. ety standards Only experts must carry out repai ring of electrical appliances otherwise considerable dan ger for the user may result Storing tools When notin use tools should be stored in the dry out of reach of children ELECTRICAL INFORMATION This product is complete with a pre wired mains plug it is double insulated in accordance with EN 50144 no earth wire is required If the plug needs replacing follow these instructions Wire correctly The wires in the mains lead are coloured in the following Way Blue Neutral Brown Live Yellow green Earth Green amp Yellow arth Fuse 5 Amp Blue Brown Neutral Live Ferm Securing the wires Secure wires carefully and firmly to the correct termi nals Secure the mains cable in the plug cord grip firmly Fit a 5 amp fuse Ifa 3amp BS1363 plug is used a BS 1362 ASTA approved 5 amp fuse must be fitted Recycle Dispose of old plug and cable Prevent inadvertent connection to socket and risk of electric shock If in doubt always consult a Qualified Elec trician ENVIRONMENT Recycle the packaging according to the identification marks onit At the end of the product or its accessories life please recycle where facilities exist phone the Helpline for current advice on recycling Helpline For any questions relating to operational or safety matters contact Ferm Customer Helplineon O1159661199 Monday Friday 8am 6pm Saturday 9am I pm GUARAN
10. indle TO MOUNT A GRINDING DISC Check the disc is the correct type and does not touch the edge of the guard Removethe flange nut 12 from the spindle Check the flange 5 is the right way up flats on spindle engage with lugs on flange Putagrinding disc 7 on the flange Screwthe flange nut onto the spindle Press the spindle lock button and turn the spindle 9 until the lock engages Keeping the spindle lock button pressed securely tighten the flange nut with spanner I provided Release the spindle lock button and check the spindle in unlocked by rotating the disc MOUNTING THE SIDE HANDLE Screw the side handle 3 clockwise into the thre aded hole either on the left or right side of the machine Check that it is firmly attached and cannot loosen unexpectedly USING THE ANGLE GRINDER BEFORE OPERATING Check the voltage on the angle grinder corresponds with your power supply voltage and that the plug and lead arein good condition Check maximum speed marked on the grinding disc is the same or less than the maximum speed of the machine The machine s speed must not be greater than the speed marked on the disc Youhave the correct type of disc for the machine and that it is mounted correctly Do not use parts other than supplied with the machine to make the disc fit properly Ensure the threaded part of the spindle is covered by the flange nut
Download Pdf Manuals
Related Search