installing the 820 extended ethernet kit
Contents
1. This wire run becomes your Ethernet backbone between the two 820 units The wire pair must be straight through and not have any connector blocks in between the 820 units If you have a connector block you must remove the 2 pair and bridge together with Telco wire butt clips ENABLE IT Page 10 of 14 Q The last step is to plug in and apply the provided 5v wall power adapter into the 820 CO unit All the LED s should illuminate and the following LED indicators will provide visual operational status of the 820 units CPE Sync Act Indicates remote LAN is visible and connected with activity If this LED fails to light the wiring between the CO and CPE is incorrect the wiring may have a short or the distance from the 820 CO through the 820 CPE to your remote LAN device exceeds 900ft or 275m CO LAN Act Indicates local LAN is visible and connected with activity CO Power should be lit when 5v adapter is connected and powered Technical Support Enable IT OEM Technical Support is available directly to customers and distributors All support requests are processed through the online support portal This allows us to provide assigned support ticket numbers in order to bring closure to any technical issues Online Technical Services The Enable IT Support Portal is available 24 7 No password or user account is necessary Please use this support website as your first source for help as it contains an on line knowledge base of articles2. B Enable IT Inc LIMITED WARRANTY ENABLE IT Page 3 of 14 NOOO OO i h 12 12 12 12 ABOUT THIS GUIDE This guide provides all the information needed to install and use the Enable IT 820 Extended Ethernet Unit This guide is intended for use by technicians who are responsible for installing and setting up network equipment Consequently it is assumed that the installer has a basic working knowledge of LANs Local Area Networks and voice telecom wiring If the information in the release notes that are shipped with your product differs from the information in this guide follow the instructions in the release notes Most user guides and release notes are available in Adobe Acrobat Reader Portable Document Format PDF or HTML on the Enable IT World Wide Web site http www ethernetextender com manuals 820 Manual pdf Page 4 of 14 INTRODUCING THE 820 EXTENDED ETHERNET KIT Congratulations on purchasing the Enable IT s 820 Extended Ethernet Kit the simplest method to stretch your broadband solutions for in building deployment in commercial office buildings hotels and multi tenant residential units The 820 Extended Ethernet Unit offers the Lowest Cost Solution in a simple design for rapid install using existing 2 pair Telco wiring This chapter contains introductory information about The 820 Extended Ethernet Kit and how it can be used in your network It covers the following topics e Abo
3. ENABLE IT S TM Enable IT 820 Series Extended Ethernet User Manual All Rights Reserved 1997 2009 ENABLE IT Proprietary and Confidential Copyright 1997 2009 Enable IT Inc All rights reserved No part of this documentation may be reproduced in any form or by any means or used to make any derivative work such as translation transformation or adaptation without written permission from Enable IT Inc Enable IT Inc reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of Enable IT Inc to provide notification of such revision or change Enable IT Inc provides this documentation without warranty term or condition of any kind either implied or expressed including but not limited to the implied warranties terms or conditions of merchantability satisfactory quality and fitness for a particular purpose Enable IT Inc may make improvements or changes in the product s and or the program s described in this documentation at any time If there is any software on removable media described in this documentation it is furnished under a license agreement included with the product as a separate document in the hard copy documentation If you are unable to locate a copy please contact Enable IT Inc and a copy will be provided to you UNITED STATES GOVERNMENT LEGEND If you are a United States government agency then this documentation and
4. documentation FAQ s and other problem solving resources This web based support resource provides the quickest solution to the most common technical support issues http www ethernetextender com support support overview php Returning Products for Warranty Repair Enable IT Inc warrants to the original purchaser of the Product you or the End User that for the one 1 year period commencing on the date the Product was purchased the Warranty Period the Product will be substantial free from defects in materials and workmanship under normal use and conditions Electrical damage is not an item that is covered under this warranty or extended warranties If authorized by Enable IT to return a Product which does not conform to the warranty set forth above the End User must 1 obtain a return materials authorization RMA number from Enable IT by contacting the Customer Service Dept at 888 309 0910 between the hours of 8 00 a m and 5 00 p m PST and otherwise fully comply with Enable IT s then current RMA policy 2 return the Product to Enable IT Inc in its original packaging freight pre paid and 3 provide to Enable IT the original receipt or bill of sale establishing the date on which the Product was purchased Please ship Authorized RMAs to Returning Products for Refund 30 Day refund applies to single kit Ethernet Enable IT Processing Facility Extenders only and is subject to a 25 16600 Harbor Blvd Ste G Restocking Fee
5. abnormal use power failure or surge or use not consistent with the operating instructions provided by Enable IT ii modification including but not limited to opening the Product housing or repair by any party in any manner other than as approved by Enable IT in writing iii fraud tampering unusual physical or electrical stress unsuitable operating or physical conditions negligence or accidents iv removal or alteration of the Product serial number tag v improper packaging of Product returns or vi damage during shipment other than during the original shipment of the Product to the End User from Enable IT if applicable ENABLE IT Page 12 of 14 e Warranty Disclaimers THE EXPRESS WARRANTY SET FORTH ABOVE IS IN LIEU OF ALL OTHER WARRANTIES WHETHER WRITTEN ORAL EXPRESS OR IMPLIED ENABLE IT DISCLAIMS TO THE MAXIMUM EXTENT PERMITTED BY LAW THE IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF THIRD PARTY RIGHTS NO PERSON INCLUDING WITHOUT LIMITATION ENABLE IT EMPLOYEES AGENTS RESELLERS OEMS OR DISTRIBUTORS IS AUTHORIZED TO MAKE ANY OTHER WARRANTY OR REPRESENTATION CONCERNING THE PRODUCT IF THE DISCLAIMER OF ANY IMPLIED WARRANTY IS NOT PERMITTED BY LAW THE DURATION OF ANY SUCH IMPLIED WARRANTY IS LIMITED TO ONE 1 YEAR FROM THE DATE OF PURCHASE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY MAY LAST SO
6. should be lit when 5v adapter is connected and powered Phone Jack 820 CO 820 CPE CAT 3 5e 6 Ethernet or 24 AWG Telco wire Patch cord LAN or PC device Patch cord 2 pair Data Voice 8 900ft or 275m 820 CPE CAT 3 5e 6 Ethernet or 24 AWG Telco wire Patch cord WiFi AP Patch cord 4 pair Data Voice PoE PoE Injector 4 900ft or 275m ENABLE IT Page 9 of 14 Performing the On Site Installation After removing the Enable IT 820 Extended Ethernet Units from the box all that remains to install the unit on site is to mount the unit add RJ 45 Male heads to your wiring connect the wiring cross connect voice lines if needed and attach end device Ethernet patch cord cabling Q Mounting the Enable IT 820 Extended Ethernet Kit The Enable IT 820 Extended Ethernet Units are designed for quick wall mounting Choose a location to mount each of the Enable IT 820 s where the maximum distance does not exceed 900ft or 275m total between devices to be connected When wall mounting the units it is recommended that you use the appropriate screw anchors for your mounting surface If mounting on existing plywood use wood screws if mounting onto drywall or sheetrock use plastic drywall anchors to secure your installation Attaching cabling and devices to the Enable IT 820 Extende
7. SUCH LIMITATIONS OR EXCLUSIONS MAY NOT APPLY THIS WARRANTY GIVES THE END USER SPECIFIC LEGAL RIGHTS AND THE END USER MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION ENABLE IT DOES NOT WARRANT THAT THE OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE ENABLE IT IS NOT RESPONSIBLE FOR ANY DAMAGE TO OR LOSS OF ANY PROGRAMS DATA OR OTHER INFORMATION STORED ON OR TRANSMITTED USING THE PRODUCT 2 LIMITATION OF LIABILITY IN NO EVENT SHALL ENABLE IT BE LIABLE TO THE END USER OR ANY THIRD PARTY FOR ANY INDIRECT SPECIAL PUNITIVE INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING OUT OF THE SALE OR USE OF THE PRODUCT INCLUDING BUT NOT LIMITED TO LOSS OF PROFIT USE DATA OR OTHER ECONOMIC ADVANTAGE HOWEVER IT ARISES INCLUDING WITHOUT LIMITATION BREACH OF WARRANTY OR IN CONTRACT OR IN TORT INCLUDING NEGLIGENCE OR STRICT LIABILITY EVEN IF ENABLE IT HAS BEEN PREVIOUSLY ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND EVEN IF A LIMITED REMEDY SET FORTH IN THIS AGREEMENT FAILS OF ITS ESSENTIAL PURPOSE IN NO EVENT SHALL ENABLE IT LIABILITY TO THE END USER OR ANY THIRD PARTY EXCEED THE PRICE PAID FOR THE PRODUCT BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES THE ABOVE LIMITATIONS MAY NOT APPLY TO THE END USER 3 LICENSE AND LIMITATIONS The firmware and software embedded in the Product the Embedded Software are lice
8. Shipments without valid Fountain Valley CA 92708 authorized RMA number or sent to our corporate Las Vegas Address can be refused and or billed for additional shipping ENABLE IT Page 11 of 14 ENABLE IT LIMITED WARRANTY Enable IT warrants the Enable IT 860 Extended Ethernet Kits solely pursuant to the following terms and conditions 1 PRODUCT WARRANTY a Express Warranty Enable IT warrants to the original purchaser of the Product you or the End User that for the three 3 year period commencing on the date the Product was purchased the Warranty Period the Product will be substantially free from defects in materials and workmanship under normal use and conditions This warranty does not apply to Products which are resold as used repaired or reconditioned or consumables such as batteries supplied with the Product Electrical damage is not an item that is covered under this warranty or extended warranties Enable IT does not make any warranty with respect to any third party product software or accessory supplied with or used in connection with the Product and such third party products software and accessories if any are provided AS IS Warranty claims related to such third party products software and accessories must be made to the applicable third party manufacturer b Remedies for Breach of Warranty In the event of a breach of the foregoing warranty Enable IT will in its sole discretion and at its cost and subjec
9. ation allows for minimal interruption and the Broadband technology allows for investment protection up to 10 years with no firmware or replacement issues Bandwidth can be scaled according to the Broadband Access Provider needs The 820 Extended Ethernet Kit is a passive device so interruption of Internet service does not affect POTS services Carriers and Access Providers can came and go but the 820 Extended Ethernet Unit technologies continue to provide lasting value such as the other utilities like Water gas and electricity The Enable 820 Extended Ethernet Kit is suited for the following key environments Commercial Buildings Multi Tenant Units Business Parks Multi Tenant Units Apartments Multi Residential Units Hotels Multi Hospitality Units Business Suites Multi Hospitality Units School Campuses University K 12 College Housing Multi Residential Units Mining Operations Quarries Mine shafts Nautical Infrastructure Cruise ships Marinas dive operations subs Video Surveillance Security WiFi Deployment ISP s RV Parks Construction sites Manufacturing Foundries pharmaceutical aerospace automotive petroleum concrete plants etc Retail POS Department stores Bars restaurants retail spaces e Government Naval ships FEMA Housing USGS National Parks Forestry Research stations NASA utilities etc e Education outdoor camps college campuses e Healthcare Hospitals elder
10. attach another Ethernet patch cord to the Data PoE IN port of the 820 CO Final step is to apply Power to the 820 CO unit LED indicators will provide visual operational status of the 820 units CPE Sync Act Indicates remote LAN is visible and connected with activity If this LED fails to light the wiring between the CO and CPE is incorrect the wiring may have a short or the distance from the 820 CO through the 820 CPE to your remote LAN device exceeds 900ft or 275m CO LAN Act Indicates local LAN is visible and connected with activity CO Power should be lit when 5v adapter is connected and powered This confirms proper operation of the units For installation at your desired location keep in mind the following The backbone cable between the CO amp CPE RJ 45 LINE ports uses 2 pairs of wiring for data and voice use only RJ 45 pins 1 2 3 amp 6 or 4 pairs of wiring for data voice and PoE All RJ 45 pins Two RJ 45 blank male heads have been provided in the kit for use in connecting your wiring to the 820 LINE ports The RJ 45 Pins are straight through just like an Ethernet patch cord See the following diagrams for specific pin details for best performance DO NOT INSERT THE BLANK RJ 45 HEADS PROVIDED INTO ANY PORTS BEFORE CRIMPING OTHERWISE YOU WILL RENDER THE PORT USELESS BENT PINS ENABLEIT Page 8 of 14 Attach RJ 45 Male heads to your existing wiring and follow the diagram below For data only
11. care outpatient facilities e Entertainment Movie theaters home entertainment fairs outdoor venues ENABLE IT Page 7 of 14 INSTALLING THE 820 EXTENDED ETHERNET KIT The Enable IT 820 Extended Ethernet Kit has a distance restriction of 900ft or 275m over Category 2 up to Category 5e wiring from device extension to device extension Therefore quick simple site surveys and installation planning are highly recommended This chapter describes the recommended installation process for the Enable IT 820 Extended Ethernet Kit It covers the following topics e Site Plan Installation Design Considerations e Unpacking the Enable IT 820 Extended Ethernet Kit e Performing the On Site Installation Site Plan Installation Design Considerations Total distance of 900ft wiring from 820 CO to LAN device on end of 820 CPE 2 Pair Telco wiring or greater for the Enable IT 820 Extended Ethernet Units Wire pair used must be straight through no taps connection points Twisted Pair cabling delivers the best performance over distance Cisco PoE single line injector support built in Transparent to single line 802 3af PoE devices We highly recommend a quick test to ensure the working order of you 820 units To do this please use one of the Ethernet patch cords provided and attach each end to the LINE port on the 820 units Next use another Ethernet patch cord to attach a LAN device to the Data PoE OUT port of the 820 CPE Next step is to
12. d Ethernet Kit Attach your remote PoE splitter or your LAN device to the 820 CPE unit Data PoE OUT RJ 45 port with one of the Ethernet patch cords provided Next attach your PoE Injector or LAN device to the 820 CO unit Data PoE IN RJ 45 port with one of the Ethernet patch cords provided If you plan on using voice service as well insert your dial tone voice line lines to the 820 CO unit Dual Voice IN RJ 11port and telephone handset to the 820 CPE unit Dual Voice OUT RJ 11 port Note If you select to input voice lines into your 820 units the Dual voice pinout is as follows The innermost pins 3 amp 4 are used for transport for voice line 1 and pins 2 amp 5 are used for transport voice line 2 cc Green 1 T3 jpam Orange M Black T2 r Blue 8 Red R1 nic Blue H Green T1 iie Orange D 5 Yellow R2 lp Green 6 Blue R3 T I I I d Modern Pin Old Pair Color Code Destination Color Code Destination UTP Quad Cable or Screw Terminal Building the backbone between the 820 units Using the provided RJ 45 blank heads crimp onto your selected 2 pair or 4 pair wiring and insert into the LINE port of each 820 unit Follow the following diagram to create a T 568A standard connection between the 820 units T 568A Straight Through Ethernet Cable
13. f Standard amp Cisco PoE Power over Ethernet support pass through Specifications Functionality 5v power consumption on CO Data Rates 15Mbps Full Duplex Passive Device No Firmware Ethernet modes supported Dimensions 10 100Mbps half duplex Height 1 2 80mm 10 100Mbps full duplex Depth 2 6 66mm Max Distance 275m 900ft Width 4 4 111mm PoE compatible pass through Interfaces Environment Operating temp 0 to 50 C 32 122 F RJ 11 dual POTS input output Storage temp 25 to 60 C 13 140 F RJ 45 10 100Mb LAN input output w PoE Humidity 596 to 9596 non condensing ENABLE IT RJ 45 Transport LINE port 5v DC Power adapter input for CO unit Page 6 of 14 Enable IT 820 Extended Ethernet Units are usually installed onto telephone wiring infrastructures where extension of backbone services is required and expensive fiber options are prohibitive The 820 Extended Ethernet Kit allow a standard Ethernet segment to be deployed quickly over existing 2 pair Telco Copper Wiring in combination with existing POTS voice signals No power is required for the remote 820 unit and Ethernet signals can be driven up to 900ft That is 572ft beyond standard CAT 5 Ethernet There are no moving parts and no firmware to upgrade thus providing maintenance free operation Typical Applications Installers have the convenience of a 10 100Mbps LAN Ethernet unit for peace of mind connectivity low power and no maintenance Rapid install
14. nsed to you Your use of the Product is your acceptance of the warranty terms above and the terms below You may use the Embedded Software solely in conjunction with your use of the Product All worldwide right title and interest in and to the Product or any portion thereof including but not limited to the Embedded Software including all copyrights patent rights trademarks trade secrets and other intellectual property rights therein and thereto are and shall remain the exclusive property of Enable IT and or its licensors You acknowledge and agree that you may not and may not allow any third party to i use the Embedded Software in a manner that is inconsistent with the above express right granted to you or ii modify distribute reproduce decompile disassemble reverse engineer or otherwise attempt to discover the source code for the Embedded Software ENABLE IT Page 13 of 14 CONTACT Us European Sales North American Sales Asia Pacific Sales 44 1 908 560200 1 888 309 0910 61 02 8898 9622 44 1 908 565533 fax 1 866 389 8605 fax 61 2 9939 0005 fax http www enable it eu http www enableit com http www enable it com au sales enable it eu sales enableit com sales enable it com au Middle East Sales Other International 97 1 50 435 8310 1 619 795 1697 http www enableit com 1 320 215 6907 fax sales enableit com ENABLE IT Page 14 of 14
15. t to the terms of the following paragraph repair the non conforming Product replace the non conforming Product with a new or reconditioned Product or refund of the purchase price for the Product Any new or reconditioned Product provided pursuant to this paragraph is warranted as provided herein for the remainder of the original Warranty Period THE REMEDY SET FORTH IN THIS PARAGRAPH SHALL BE THE END USER S SOLE AND EXCLUSIVE REMEDY FOR BREACH OF THE FOREGOING WARRANTY c Conditions for Warranty Qualification If authorized by Enable IT to return a Product which does not conform to the warranty set forth above the End User must 1 obtain a return materials authorization RMA number from Enable IT by contacting the Customer Service Dept at 888 309 0910 between the hours of 8 00 a m and 5 00 p m PST and otherwise fully comply with Enable IT then current RMA policy 2 return the Product to Enable IT in its original packaging freight pre paid and 3 provide to Enable IT the original receipt or bill of sale establishing the date on which the Product was purchased Products returned to Enable IT without an RMA number will be returned to the End User Enable IT shall not be responsible for damage or loss during shipment of the returned Product to Enable IT d Voiding of Warranty The express warranty set forth above shall not apply to failure of the Product if the Product has been subjected to i physical abuse misuse improper installation
16. the software described herein are provided to you subject to the following All technical data and computer software are commercial in nature and developed solely at private expense Software is delivered as Commercial Computer Software as defined in DFARS 252 227 7014 June 1995 or as a commercial item as defined in FAR 2 101 a and as such is provided with only such rights as are provided in Enable IT Inc s standard commercial license for the Software Technical data is provided with limited rights only as provided in DFAR 252 227 7015 Nov 1995 or FAR 52 227 14 June 1987 which ever is applicable You agree not to remove or deface any portion of any legend provided on any licensed program or documentation contained in or delivered to you in conjunction with this User Guide Unless otherwise indicated Enable IT Inc registered trademarks are registered in the United States and may or may not be registered in other countries Page 2 of 14 CONTENTS ABOUT THIS GUIDE 1 INTRODUCING THE ENABLE IT 820 EXTENDED ETHERNET KIT About the 820 Extended Ethernet Kit Key Benefits Summary of Features Typical Applications 2 INSTALLING THE ENABLE IT 820 EXTENDED ETHERNET KIT Site Plan Installation Design Considerations Unpacking the 820 Extended Ethernet Kit Performing the On Site Installation Mounting the 820 Extended Ethernet Units A TECHNICAL SUPPORT Online Technical Services World Wide Web Site Returning Products for Repair
17. the un powered 820 end by using the spare pairs in a CAT rated cable Unit Model Wiring Data Rate Max Distance 820 2 pair CAT 2 up to CAT5e 15MB FD 900ft 275m ENABLE IT Page 5 of 14 Key Benefits The following list identifies the 820 Extended Ethernet Kit key benefits Dramatic cost reduction over any competing technology The Enable IT 820 Extended Ethernet Kit require No Power CPE remote end No Firmware No Maintenance Broadband technology that delivers in building Ethernet access over 2 pair of existing Category 2 up to Category 5e wiring up to 900 whether spare or actively in use for analog or digital voice This means no new wiring is required Provides one scalable infrastructure for Internet access dual POTS VoIP video Power over Ethernet PoE and virtual private networking Rapid installation with small box profile no programming and no firmware to upgrade Low profile box with dual POTS line PoE and Ethernet data all in a single RJ 45 Ethernet jack Summary of Features The Enable 820 Extended Ethernet Unit has the following hardware features e 1 Extended Ethernet line over existing CAT 2 Telco up to CAT5e wiring e Rapid Telco style installation no programming required e Supports digital VoD channels e Drives Ethernet 15 Mbps full duplex service delivery up to 900ft 275m e Network Equipment independence Transparent to protocols applications MAC e Maintains lifeline POTS e 802 3a
18. use pins 1 2 3 amp 6 For Data and PoE use all pins PoE uses pins 4 5 7 amp 8 T 568A Straight Through Ethernet Cable Clip is pointed away from you Unpacking the Enable IT 820 Extended Ethernet Kit Carefully remove the Enable IT 820 Extended Ethernet Units all packing materials from the box Verify that the items listed below are present Make sure that the equipment supplied matches what you ordered If any items are missing or damaged please contact your Enable IT or your distributor for assistance e 2 Enable IT 820 Extended Ethernet Units 1 CO amp 1 CPE e 1 5v Wall power adapter for originating 820 CO unit powered with LED s e 2 LAN Ethernet Patch Cords for end device attachment e 2 RJ 45 Blank Male heads for use on your wiring e Enable IT 820 Extended Ethernet Unit User Manual this manual It is highly recommended you test and become familiar with the basic operation of the units before installing in the field Use one of the provided LAN patch cords in the kit to connect the 820 CO and CPE LINE ports together Power the CO and test your equipment LED indicators will provide visual operational status of the 820 units CPE Sync Act Indicates remote LAN is visible and connected with activity If this LED fails to light the wiring between the CO and CPE is incorrect the wiring may have a short or exceeds 900ft CO LAN Act Indicates local LAN is visible and connected with activity CO Power
19. ut the 820 Extended Ethernet Kit e Key Benefits e Summary of Features e Typical Applications DO NOT INSERT THE BLANK RJ 45 HEADS PROVIDED INTO ANY PORTS BEFORE CRIMPING OTHERWISE YOU WILL RENDER THE PORT USELESS BENT PINS About the 820 Extended Ethernet Kit The 820 Extended Ethernet Kit solves the problem of high costs associated with stretching your backbone with traditional fiber or a series of hubs repeaters In many office buildings preferred network access is a dedicated Ethernet line however Ethernet over twisted pair wiring has its distance limitations of just 328 ft In order to drive Ethernet signal further one would have to add repeaters to each segment of 328ft twisted pair cabling this is often insufficient and to costly in multi story buildings Fortunately the Enable IT 820 Series Extended Ethernet can push the reach of Ethernet to more than 2 times the typical Ethernet distance A simple design methodology would be to think of the 820 extending a standard Ethernet line with power PoE up to 900 275m and can also include 2 voice lines simultaneously To increase the durability and extended use of the product providing maximum future technology protection 820 Extended Ethernet Unit meets the challenge of modern switched LANs and allows you to add features and capacity as your network expands The 820 LRE kit includes a powered switch end and an un powered remote end POE adapters can be used in conjunction with
Download Pdf Manuals
Related Search