Home

NXQ™ Flat-Panel Wall Speaker

image

Contents

1. lt NXQ Flat Panel Speaker Installation Instructions Wall Speaker LightSPEED Start your system installation with the All LightSPEED speakers should be installed in System Installation section of the User Manual accordance with Uniform Building Code state and local building department requirements Step 1 Selecting Speaker Mounting Location gt gt gt Room Installation Top View One NXQ Flat Panel Wall Speaker is designed for rooms less than figure 1 1200 sq ft and with a ceiling height of 9 12 feet Before starting the system installation speaker placement needs to be decided This speaker is designed to be centered on the long wall of the classroom figure 1 Ceiling height must be 9 feet or higher and the speaker should be mounted 6 5 7 feet from the floor figure 2 If the classroom is not rectangular or has a ceiling that is not horizontal flat call LightSPEED Technical Support 800 732 8999 to determine gt gt gt Side View optimum speaker placement figure 2 Step 2 Mounting the Speaker 9 ft A Measure 6 5 7 feet up on the center of one of the long walls to determine approximate speaker location The speaker comes with 6 5 7ft standard picture hangers Attach the hangers to the wall in the same manner as if hanging a picture The speaker has a wire on the back that will allow it to hang on the wall Do not hang the speaker until after B is completed gt gt gt Connectio
2. n of Speaker Wire to Back of 750iR B Locate the coil of speaker wire To connect the wire to the speaker press down on the colored terminals on the back of the ngure a TE ff Black speaker insert the wire and release the tab to hold it in place Using Pa the end with the two colored wires insert the black wire into the WAAR black tabbed terminal and the red wire into the red tabbed terminal Hang the speaker on the hanger in the same manner as hanging a picture Step 3 Connect Speakers and Wire to the Receiver Amplifier A Run the wire by best route from the speaker to the receiver amplifier For permanent installations it is usually best to route wire overhead when possible It is common practice to run speaker wire above suspended ceiling tiles NOTE wiring should be installed and secured according to state and local school building codes B Connect the other end of the speaker wire to the receiver ampilifier in the following manner based on the system type 750iR see figure 3 i Unscrew the red and black caps on the binding post connectors ii Insert the bare red wire into the red hole that was revealed by unscrewing the red cap and the black wire into the hole on the black connector iii Screw the caps back down onto the wires until they are secure iv Make sure the speaker on off switch next to the jack is switched to the on position lt NXQ Flat Panel Speaker Installation Instructions Wall S
3. nt of you not to amplify your voice at high volumes Because of the classroom size and constant proximity to the speaker the system can product feedback squealing if the volume level is set too high C Return to Step 4 Receiver amplifier of the install section of the user manual to complete the remaining steps of the system installation
4. peaker LightSPEED All LightSPEED speakers should be installed in Start your system installation with the accordance with Uniform Building Code state System Installation section of the User Manual and local building department requirements 780iR see figure 4 gt gt gt Connection of Speaker Wire to Back of 780iR i Insert the 1 4 plug into the SPEAKER OUTPUT 1 jack on the back of the receiver ampilifier SPEAKERS ii The speaker volume knob should be left at the 12 00 position ea o o o 9 l DOO iii Make sure the corresponding speaker on off switch on the front panel is set to the on position C Speaker wire should be secured to the wall and concealed if desired with wire mold gt gt gt Factory Recommended EQ Settings Step 4 Equalization figure 5 A Each regal AMG includes an 8 band equalizer that allows 250400 e00 1K KG 25 aK B users to fine tune their classroom based on different room characteristics Figure 5 shows the factory recommended settings for the NXQ speaker Since all rooms are different this is only meant as a starting point and may require some adjustment U U U HU H H 4 EQUALIZER B The ideal sound is a crisp clear sound with no feedback Volume levels should be set to a point you can barely hear your own voice The goal is to try to replicate the sound of your voice as if the child is sitting directly in fro

Download Pdf Manuals

image

Related Search

Related Contents

Operating Instructions MA 52  M-Systems Flash Disk Pioneers 48-SR-003-03-7L User's Manual  2 - 酒井・泉研究室  Philips 872790021185625 energy-saving lamp  GYNECOLOGIE - OBSTETRIQUE ET CHIRURGICALE  Giga-tronics ASCOR Model 3000  Hotpoint Washer WMD 962 P/G/A/K User's Manual  TRAKTOR PRO / TRAKTOR SCRATCH PRO – Manuel d`utilisation  TDG34 - APRICANCELLO GSM CON ANTENNA INTEGRATA  

Copyright © All rights reserved.
Failed to retrieve file