User Manual - Witura Technology Sdn Bhd
Contents
1. WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual The GSM unit will send this reply message RER1 ON Adjusting the Microphone and Speaker Volume This setting allows you to adjust the Microphone and Speaker volume of the WT 1010LM unit by handset In Program Mode Press 15 Example To set both the microphone and speaker volume to 4 press 15 44 SPK 4 MIC 4 Note The speaker volume ranges from 1 9 Default 5 The microphone volume ranges from 1 9 Default 5 Setting PIN Code for the WT 1010LM Device This setting allows the WT 1010LM to recognize the SIM card with the programmed PIN code In Program Mode Press 12 Enter twice the 4 digits PIN code followed by e g 1234 PIN 1234 OK WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual Clear the PIN Code of the WT 1010LM Device Clear the programmed PIN code HANDSET In Program Mode Press 14 Enter either the digit O Cancel or 1 Confirm Clear PIN Check the PIN Code of the WT 1010LM Device Check the programmed PIN code HANDSET In Program Mode Press 13 The PIN code will be displayed as below PIN code is 1234 Enable SIM PIN Protection This setting allows you enable SIM PIN protection HANDSET In Program Mode Press 18 Enter the 4 digits PIN code followed by e g 1234 WITURA CORPORATION SDN BHD2. GSM Lift Emergency Voice amp Monitoring System Instruction Manual PIN Protected ON PIN 1234 Disable SIM PIN Protection This setting allows you disable SIM PIN protection HANDSET In Program Mode Press 19 Enter the 4 digits PIN code followed by e g 1234 PIN Protected OFF PIN 1234 Learning Mode for Remote Control This setting allows you program the remote controls HANDSET In Program Mode Press 17 Press any button on the remote control to learn RF Learn OK WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual Reset the WT 1010LM Unit This setting allows you reset the WT 1010LM Unit HANDSET In Program Mode Press 21 Enter either the digit O Cancel or 1 Confirm Reset The Machine 1 OK WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual
3. amp WITURA WT 1010 WT 1010LM GSM LIFT EMERGENCY VOICE amp MONITORING SYSTEM User Manual and Installation Instructions Version 1 1 Updated 27 OCT 2011 WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual Overview WT 1010LM GSM Lift Emergency Voice amp Monitoring System is a wireless emergency communication system designed for emergency calls from a lift cabin to the monitoring centre service department security personnel etc over GSM network The unit works perfectly with any emergency lift phone in the market GSM lift emergency voice system applies because GSM call cost is better than landline and no monthly fixed charges This system also applicable in every building where there is no person who monitors lift s condition constantly It is the ideal solution for companies which have greater number of lifts all they need is one telephone number e g mobile phone s on which messages and voice connections will be transferred The unit also suitable for offer temporary communication solutions at construction sites where the telephone line has not yet been installed RJ 11 Telephone Line l l i i l Lift Control Room l i l l l l Elevator Failure Alarm amp Monitoring Centre When a trapped lift passenger presses the button on the lift phone for emergency the lift phone automatically calls up an alarm centre or security perso
4. press 29 120000 WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual TIME 12 00 00 OK To program the internal time clock by SMS send SETM HH MM SS HH Hour MM Minutes SS Seconds Example To program the time to be 5 30PM send SETM 17 30 00 The GSM unit will send this reply message Set Time OK Set the Account Number for Event Reporting When Input triggered or AC failure the WT 1010LM will dial the programmable central station number and transmit the account number along with Contact ID to the central station HANDSET In Program Mode Press 32 Enter the 4 digits account number followed by e g 1234 Example to program the account number as 1111 press 1111 ATACC 1111 OK Check GSM Signal Strength Check the GSM signal strength by handset or SMS HANDSET In Program Mode Press 34 WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual The display will show the signal strength 0 Poor signal 31 Best signal 99 unknown or not detectable CSQ lt 28 gt OK To check GSM signal strength by SMS send CSQ The GSM unit will reply for example CSQ lt 28 gt Check Version To check the software and hardware version by handset HANDSET In Program Mode Press 20 The display will show for example HW 1 1ver SW 1 0 Ver MW 1 0ver Remote Control Outputs by
5. 25 OK Note The Waiting time range from 20 59 seconds Default 30 seconds Program the AC Power Failure Options This function enables the possible alarm action for AC power failure HANDSET In Program Mode Press 28 to program AC Power Failure alarm options AC Power Failure Options ME Send SMS alert when power failure AL Activate the strobe light when power failure CA1 Call Admin number when power failure CA2 Call Admin number when power restored Enter either the digit O Disable or 1 Enable for the 4 possible actions for the AC power failure alarm followed by Example To enable the system to send SMS alert and activate the strobe light when AC power failure press 1100 ADC ME 1 AL 1 CA1 0 CA2 0 Note If the system calls you when the power failures simply answer the call and press to acknowledge the alarm and the system will stop calling you WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual AC Power Failure Message This option sets the SMS text content which is sent when AC power failure ACPF message content message content Up to 50 alphanumeric characters Letters and numbers only no special characters Example To program the system to send SMS message Lift Power Down send ACPFH Lift Power Down The GSM unit will send this reply message ALOFF Lift Power Down AC Power Restored Message This option sets t
6. SM unit will send this reply message USC1 Lift Function Closed Program the Strobe Light Siren Output Duration To program the strobe light siren output duration on PIN24 and PIN25 The alarm time can be set between 00001 to 99999 seconds Note that programming duration of 00000 seconds has no effect HANDSET In Program Mode Press 33 Example To program the strobe light siren output duration to 10 minutes press 33 00600 WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual Alarm Time 00600 To program the strobe light siren output duration by SMS send ALTM time time strobe light siren output duration in seconds between 00000 and 99999 seconds Example To program the output duration to 10 minutes send ALTM 00600 The GSM unit will send this reply message ALTM 00600 Enable Disable the Activation of Strobe Light Siren Output when Input Triggered Use this option to enable or disable the activation of strobe light siren output when input triggered ALM N X N Input number 1 or 2 X 1 Enable or 0 Disable Example To enable this function send ALM1 1 The GSM unit will send this reply message ALM1 ON Set the Time Clock This setting allows you to program the internal clock of the device The time is set in 24HR format In Program Mode Press 29 to program the internal clock Example To program the internal clock as 12 00 00
7. SMS This allows you to turn outputs on by SMS This can be used to reset lift or switch on lift function by a relay Note The mobile phone used to send SMS commands must be programmed as Admin Phone Number RLY N time N Output number 1 or 2 time relay on time in seconds between 00000 and 99999 seconds To toggle outputs send the text ON or OFF instead of a time value See the example below WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual Example 1 To program Output 1 to stay on for 20 seconds send RLY1 00020 The GSM unit will reply RLY1 00020 Example 2 To program Output 1 to stay on indefinitely send RLY1 ON The GSM unit will reply RLY1 ON Control Outputs by handset This allows you to turn outputs on by handset HANDSET In Program Mode Press 10 to switch on Output 1 Press 11 to switch on Output 2 Example To activate Output 1 for 10 seconds and send an SMS message when the output has turned off press 10 000101 RLY1 00010 RE 1 The options for RE are 0 Do not send SMS reply when the output turns off 1 Send SMS reply when the output turns off Setting the SMS Reply for Output Relay Off This setting allows you to enable disable the SMS reply when the output turns off by SMS RER N X N Output number 1 or 2 X 1 Enable or 0 Disable Example To enable the SMS reply function for output relay 1 send RER1 1
8. g Mode To exit program mode simply hang up the handset Program the Installer Code The installer code is used to access program mode via handset To program a new 8 digit installer code simply press 0 in program mode Enter the new installer code followed by eg 87654321 The display will show NEW PASSWORD 87654321 To exit programming mode simply hang up the handset NOTES DO NOT LOSE THE INSTALLER CODE AS IT CANNOT BE RECOVERED IF LOST OR FORGOTTEN YOU WILL NEED TO CONSULT WITH OUR TECHNICAL PERSONNEL FOR RESETTING THE SYSTEM TO DEFAULT STATE Admin Phone Number 1 must be programmed to allow sending of SMS commands to the GSM Unit WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual ATTENTION PROGRAMMING METHODS HANDSET AND SMS COMMANDS Please note that some options are programmed using a telephone handset connected to the GSM unit and other options are programmed by SMS message sent from a mobile phone SMS COMMAND options are programmed by sending an SMS message from a mobile phone to the GSM Unit The mobile phone used to send SMS Commands must be programmed as Admin Phone Number 1 Program the Admin Phone Numbers Up to 8 Admin phone numbers can be programmed These are mobile phone numbers to which the GSM Unit can send SMS messages such as alarms from inputs or system messages Here you should program the technical or security personnel numbers etc Yo
9. gered CA1 Call Admin number when Input Triggered CA2 Call Admin number when Input Restored Enter either the digit O Disable or 1 Enable for the five possible actions for the input followed by Example To enable Input 1 to send SMS Alarm and Restoral messages and activate the strobe light when input is triggered press 26 11100 IN1 OP 1 CL 1 AL 1 CA1 CA2 Follow the same procedure for input 2 Note If the system calls you when the input triggered simply answer the call and press to acknowledge the alarm and the system will stop calling you WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual Input Alarm Message This option sets the SMS text which is sent when an input is triggered USE N message N Input number 1 or 2 message Up to 50 alphanumeric characters Letters and numbers only no special characters Example To program Input 1 to send the SMS message Lift Function Open send USE1 Lift Function Open The GSM unit will send this reply message USE1 Lift Function Open Input Restoral Message This option sets the SMS text which is sent when an input is restored USC N message N Input number 1 or 2 message Up to 50 alphanumeric characters Letters and numbers only no special characters Example To program Input 1 to send the SMS message Lift Function Closed send USC1H HLift Function Closed The G
10. he SMS text content which is sent when AC power restored ACPR message content message content Up to 50 alphanumeric characters Letters and numbers only no special characters Example To program the system to send SMS message Lift Power Restored send ACPR Lift Power Restored The GSM unit will send this reply message ALON Lift Power Restored Enable Disable the Alarm Input Function This option allows you to enable disable the function of alarm input HANDSET In Program Mode Press 16 to enable disable the function of 2 alarm inputs To enable the function of 2 alarm inputs press 11 To disable the function of 2 alarm inputs press OO CTR1 1 CTR2 1 OK WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual To Enable Disable the Alarm Input Function by SMS send CTR N X N Input number 1 or 2 X 1 Enable or 0 Disable Example To enable the alarm input 1 function send CTR1 1 The GSM unit will send this reply message CTR1 ON Program the Alarm Input Options This option enables the possible actions of 2 alarm inputs of the unit HANDSET In Program Mode Press 26 to program Input 1 alarm options Press 27 to program Input 2 alarm options Input Options OP Send SMS Alert when Input Triggered Alarm Input to 12V CL Send SMS Alert when Input Restored Remove 12V from Input AL Activate Strobe Light Siren when Input Trig
11. nnel number via the GSM network When voice communication is established the person can talk to the staff at the alarm centre where help will be dispatched The unit also the reporting and monitoring system provides monitoring the working status of lift and escalator over GSM network When there is a failure or power failure the WT 1010LM GSM unit will automatically generate SMS alert to the pre programmed telephone number up to 8 The system has 2 low voltage alarm inputs which can be connected to the lift for alarms about Panic situation lift functionality etc It is also possible to remotely control the 2 30A output relay of the GSM Emergency Lift Dialler to reset the lift or to completely shut down the lift WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual RJ 11 Telephone Line Lift y el a Power i Failure oa GSM Emergency Lift Dialler SMS to Mobile Phone Power Failure 240VAC Power from Lift Input 1 to Panic Button Input 2 to Lift Function Elevator Failure Send SMS to Reset Lift Alarm amp Monitoring Centre Features Support Dual Band or Quad Band GSM Network Can connect to existing lift phone for emergency call LCD Display for indication of calling number Programmable by PC or SMS command SMS alert during lift power failure Remotely control of 2 output relays contacts for lift reset switch off lift by SMS 2 low voltage input
12. ress 24 Enter the prefix max 4 digits followed by eg 04 AREA CODE 04 OK Note Once programmed the Phone Number Prefix cannot be deleted it can only be replaced by a new prefix Use 25 option to enable and disable dialling of the prefix Enable Disable Phone Number Prefix Use this option to enable the dialling of the Phone Number Prefix HANDSET In Program Mode Press 25 To enable the Phone Number prefix press 1 To disable the Phone Number prefix press O ENABLE AREA Setting the Delay Time for Sending the Destination Number This setting enables the dialled destination number to be sent out automatically after a preset time HANDSET In Program Mode Press 9 Enter the Delay time Max 2 digits followed by e g 05 WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual Lo Dttransmit 05 OK Program the Alert Recipients This option sets which of the 8 Admin Phone Numbers will receive SMS alerts In Program Mode Press 22 to select the option Enter either the digit O No alert or 1 Send alert for each of the 8 Admin Phone Numbers followed by Example 1 to enable all Admin Numbers for alerts press 11111111 SECH 11111111 OK Example 2 to enable only Admin Numbers 1 2 amp 3 for alerts press 11100000 SECH 11100000 OK To program the alert recipients by SMS send SECHH XXXXXXXX XXXXXXXX stands for posi
13. s for sending SMS alerts when input changed state High Low 1 independent output for activating the strobe light siren when power failure Battery Backup for up to 6 hours in event of power failure Check signal strength via SMS Configurable SMS alert content WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual INTERNAL VIEW LCD Display SIM Card Holder Ga Pete eeeeees RF Receiver GSM Module Main Switch Jumper DC Power Connector Phone Port Line Port Digital Inputs 2 Relay Outputs Antenna Connector WIRING DIAGRAM be e D K a A ed ar aE a a z ocOoOusu oO u i c SEs SEs C Ta z z X a z Z o v v x Relayi Relay2 2 2K Resistor Reserved Port 5 as vz Alarm Speaker Output 12VDC AG AUX OUT 5V Output whan main power failure Note A 2 2K Resistor must be attached along with the sensors for all inputs WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual PROGRAMMING THE UNIT To program the unit you just need any fixed line telephone and connect it to the TEL port on the GSM unit Any fixed line OT telephone for programming wR wre GSM Emergency Lift Dialler ENTER PROGRAM MODE To enter program mode pick up the telephone handset and dial 12345678 default installer code The display will show HAND FREE The GSM Unit is now in Programmin
14. tion of each of the 8 Admin Phone Numbers Enter either the digit O No Alert or 1 Send Alert Example to enable all Admin Numbers for alerts send SECH 11111111 The GSM unit will send this reply message SECH 11111111 WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual Ls Enquire the Setting of Alert Recipients Check the setting of alert recipients using a handset HANDSET In Program Mode Press 35 The Alert Recipients will be displayed in sequence SECH 11110000 Setting the Calling Group of Administrator This setting will enable the system to call the certain group of administrator numbers when Input triggered or AC power failure HANDSET In Program Mode Press 23 Enter the number 1 8 Max 1 digit followed by Example to enable the system to call the first 3 administrator numbers press 3 CALL 3 Setting the Waiting Time for Engaged Call In the event the administrator has not answered the call or engaged it could take a while for the WT 1010C2 to call the next number This setting allows you to shorten the waiting time when it is busy or engaged HANDSET In Program Mode Press 31 WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual Enter the Waiting Time Max 2 digits in seconds followed by e g 25 Example to program the waiting time as 25 seconds press 25 Wait Time
15. u can program the unit to send SMS alarms to one or all Admin numbers HANDSET In Program Mode Press 1 to program the Admin Phone Number 1 Enter the phone number followed by eg 0124694739 TEL 0124694739 1 To program Admin Phone Number 2 to 8 repeat the sequence above using 2 3 4 5 6 7 Q To DELETE a Phone Number enter with no phone number eg To delete Admin Number 1 In Program Mode Press 1 To program the Admin Phone Number by SMS send TEL N phone number N Admin position 1 8 phone number Admin phone numbers WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual D Example to program phone number 0163934857 as Admin 1 send TEL1 0163934857 The GSM unit will send this reply message TEL1 0163934857 Enquire all Admin Phone Numbers To display all the Admin Phone Numbers locally using a handset In Program Mode Press 30 Each Admin Phone Number will be displayed in sequence ADMIN l 1 0124694739 To display all the Admin Phone Numbers by SMS ADM The GSM unit will send this reply message Example 1 0124694739 2 Oore O U WITURA CORPORATION SDN BHD GSM Lift Emergency Voice amp Monitoring System Instruction Manual Area Code Phone Number Prefix To program prefix digits which will be automatically dialled before any phone number HANDSET In Program Mode P
Download Pdf Manuals
Related Search