GSM/GPRS/GPS Vehicle Tracker Device User Manual
Contents
1. arm This alarm is disabled when the device receives command noarm When the alarm is enabled it will be triggered when the door of the vehicle is opened When the alarm is triggered it will be sent at an interval of 3 minutes and can be stopped when The device receives a command of mask Shock Sensor alarm Alarm indication shake alarm This alarm is enabled when the device receives command arm if the device didn t receive command shake before and set the trigger level to 2 or the device receives command shake with a level higher than 0 and set the trigger level to the value specified in the command This alarm is disabled when the device receives command noarm if this alarm is not enabled by command shake or the device receives command shake with a level of 0 When the alarm is enabled it will be triggered when the shock sensor detects a shaking with a level higher than the trigger level When the alarm is triggered it will be sent at an interval of 3 minutes and can be stopped when the device receives a command of mask ACC alarm Alarm indication acc alarm This alarm is enabled when the device receives command arm This alarm is disabled when the device receives command noarm When the alarm is enabled it will be triggered when the device detects the vehicle is engine on When th2. Operation Temp 20 C to 65 C Humidity 5 95 non condensing SIM CARD Installations Installation Steps Use a tweezers or other sharp things to press the SIM CARD popup switch Take out the SIM card slot after it is popped up Put SIM card into the SIM card slot and insert it back to its original position after confirming the SIM card at the right place Attentions e Please don t insert change or remove SIM card when the tracker device is working If you need to this please confirm that the device is power off e Please check SIM card and make sure that incoming calls display is available call transfer is forbidden and the PIN code is locked The SMS must be TXT format The PDU format will not be supported by device e Please ensure that GPRS function of your SIM card is available The GSM base station location and the communication between the tracking software server and the device need to be supported by GPRS function If your device only work in SMS control mode the GPRS function is unnecessary e The device only supports GSM network WCDMA or other 3G SIM cards are not supported SD CARD Installations Installation Steps Insert the SD card Micro SD card into the corresponding card slot in the correct direction If you need to remove the SD card from the device just press the SD card and it will be popped up automatically Attentions Please don t insert or remove the SD card when the device working If you need do thi
3. ac network the base station location information Locating When GPS Number of Star Search is less than 4 GPS Lat Lon The device Current coordinate position gpsNum 6 Speed 0 1 Alt 118 9 displays the coordinates of the location may not be accurate 13 01 07 03 20 Speed Show The current moving speed of Bat 100 Signal 20 Alt 118 9 indicating the location Altitude IMEI 860153000432571 Imei Device ID number http maps google Imei Device ID number com Link Through the mobile browser view the GPS location map maps f q amp q 40 055667 0 116 3240700 amp z 16 Auto track continuously Command Send SMS command tn password space timing interval space Locating times to the tracker device Example Send SMS tn123456 030 005 to the device It will report the Geo info for 5 times each 30s intervals Send SMS tn 123456 030 to the tracker device it will reply the Geo info continuously at 30 seconds intervals Cancellation Send SMS notn password to the tracker device to cancel the auto track Example Send SMS notn123456 to the tracker device to cancel the auto track Attentions The timing interval device should be second range should be 30s 86400s 5 Real Time Voice Monitoring Enter Real Time Voice Monitor State Command Send SMS monitor password to the tracker device it will enter the voice monitoring state the device will reply monitor ok In this state t
4. deletion and so on 11 Power Off Alarm Alarm indication power off alarm This alarm is always enabled and will be triggered when the voltage of the backup battery is lower than 3 4V and no external power supply available This alarm will be sent only once and the device will power off after sending out the alarm V LED indicator status LED Indicator LED Status Flash fast 1S times Low power GSM LED Flash slow 3S times Normal Green Green LED is on constantly Searching for GSM network OFF OFF GPRS GPRS LED Red Flash fast 1S times GPRS Offline Flash slow 3S times GPRS Contact GPS LED Blue OFF GPS power down Flash fast 1 S times Searching GPS signal Flash slow 3S times Get GPS signal VI Operation Suggestions In order to extend the device life please comply with the following instructions Keep the device dry Any liquid i e rain moisture may destroy or damage the L AS O inside circuitry Don t use amp store the device in dusty places Don t put the device in overheated or overcooled places Handle carefully Please don t vibrate or shake it violently Clear the device with a piece of dry cloth Don t clean in chemicals detergent Don t paint the device this may cause some foreign materials left in ports 7 Don t disassemble or refit the device 8 Please read the user manual carefully before your ins
5. for no apn gprs error for no ip address tcp port Possible notifications GPRS is not available Please contact the network service provider to solve this problem APN is invalid If you make sure the name user name and password are all correct please contact the network service provider to solve this problem Failed to connect to the PC tool please check the config of ip and tcp port Please make sure the PC monitoring tool is already started and ready for work 24 25 26 27 and the IP address TCP port are both correct GPRS tracking mode logout Command Send SMS command tracker password to order the device quit the tracking mode disconnect to the GPRS monitor server and switch back to the SMS control mode Example Send SMS command tracker123456 to the tracker device GSM Base Station Positioning When no valid GPS signal received the tracker device will try to locate itself by GSM GPRS network This functionality can not work unless the SIM card is GPRS available and a valid APN has been set Note This feature is available for most countries However it may be not available in some area depending on the local GSM network Get Temperature and Humidity Get the Temperature Command Send command tempget password to acquire the Temperature of the device Response The device will reply a SMS including the Temperature Attention Temperature values for degrees Celsi
6. sent spd indicating the speed when the alarm is triggered sent alt indicating the height of the place at where the alarm is triggered sent timestamp indicating when the alarm is sent The following table shows a list of possible alarm indications Alarm for Alarm Indication Enabled Disabled By By SMS SMS low battery volume battery alarm bat batVol the External supplier power supply is power stop alarm pstp nopstp stopped asking SOS HELP ME the door is open door open alarm arm noarm the device detecting a shaking of a shake alarm arm noarm certain degree shake noshake the ACC is on acc alarm arm noarm The device move alarm move alarm move nomove arm noarm the device is out of the electronical fence stock alarm stock nostock the device exceeds the speed limit Speed alarm speed nospeed Lacking SD card space Sd card insufficient alarm remains vol MB the device it to be power off power off alarm 1 Lower Power Alarm Alarm indication battery alarm bat batVol Tracker device backup battery operating voltage is range of 3 3v 4 2v If the battery is less than 20 the tracker device will send SMS battery alarm bat batVol to t
7. 13 Shi Authorization li ic aaa 13 yO ON Eo er y AAA e PP o o ste tees hots sagceess N E AT ET 5 RealTime Voice Monitoring 6 Offline Voice Recording 7 IMEICOA 2 o e teeter rereae re 15 8 Timezone Setting 9 Geo fence 10 Moving Alarm 11 Overspeed Alarm 12 Cut off the Oil and Power System 13 Resume the Oil and Power System 14 MM A O ia da 15 TE o Po E RETES 16 Tracking Trace Rec rding irsinin oiire een i rE NEEE E EE RE EEE E E EE 17 Check the Devices Working Matus a 19 18 Check The Device s Config Information cccccescccssesssscsseecssscsseesseecsaeesseeseaecesseeseneeceecsseccseessueseseeseneesaeessneseneeeuaes 20 19 External power supply cut Off lar ii iii 21 ZO SOS Plaines dsc e ass 21 21 APN setting for GPRS network ACCESS ccsccsssccsssessceeseessseesesesseeesesesenecsueesssusesseesesesssesseesssusesesessueesesesenesseetsssaeess 21 22 IP and Port Setup for GPRS network ACCESS cccssccessesssesseecsscecsneesseesuecsaeecsuescuseeusneccasecsuesensessueseaeesaneseaeeesseesaeeess 22 23 Connect tothe Monito e ind 22 24 GSM Base Station Positioning 25 Get Street Addressee ioe cds techsanscagdeasd ow A A 00s oo Aid LS AE RRA Re ee se en ee 4 Tracker Device Hardware Reset 5 F netiom Of Remote Controllers iii ee a E a E aE A a N REEE O 1 LOWErPOWEF Alar Minen E E desde ve A ee eee aces 2 External power supply cut off alarm A ds A sce E A a ca
8. GSM GPRS GPS Vehicle Tracker Device User Manual Preface Thank you for purchasing our GPS tracker device This manual shows how to use the product smoothly and correctly Before using the product please read this manual carefully Please note that specification and information are subject to changes without prior notice in this manual Any change will be integrated in the latest release The manufacturer assumes no responsibility for any error or omission in this manual Content L Bunch on Introd AA AS a ea A 3 1 Main FOAtures sccvscccstesex secesesveceseieuensevececeuet A AA E 3 E o Le EA E Sake E E E A AEN AE A AT EE A E EE EEE 3 As A A 4 5s A O A 5 6 SIM CARD litstallati Om sarerea aa a A A a a 6 Te TECARD Instalan a 6 8 Install the device into the VENICIC csccesccesseessecessecsssceseecssecsaeesseecsscecnseeeaeecsusesseecsueseseeseessaeseeessaeeseeessnseeseessneeaes 7 9 Turmonthe Tracker DEVICE cia da iden 8 M Tracker Device Operating Mode iscss cscad ssas cssseescazssattaceacaastascataagavensatencasdtaatsdasstgacsencaateansienssaniteaieanbaagastaas 8 MA E 9 1 SMS COMMANA O Matias A A oa 9 Ze SMS Command listar ira 10 3 SMS Command Response Notification Alarm explanation by FUNCtiONS oconconccnncnconconanononnconnononon ccoo noo ncno non nonnnannos 13 T WPAN ZATION sce casete e a ova Soeeuee sues Pa caw souabaea duces a a A E AE EAE EIN EEN 13 2 Change PassWord ess nee a a e dd a eae
9. SMS command resume123456 to the tracker device Response The device will reply Resume ok and resume your car engine at the same time Arming Setup Arming Command Send SMS command arm password to the tracker device This command is used to enable the safe guard function and could only take effect when the car engine is off ACC voltage is low and the door of the car is closed When the safe guard is set successfully engine on alarm door open alarm car shaking alarm and the car moving alarm will be enabled automatically Response The device will reply arm ok Other possible error responses arm error for no master set arm error for the ACC is on Example Send SMS command arm123456 to the tracker device Cancel Arming Command Send SMS command noarm password to the tracker device to disable the arming state This command is used to disable the safe guard function When the safe guard is turned off engine on alarm door open alarm car shaking alarm and the car moving alarm will be disabled automatically unless these alarms were enabled by other related commands Example Send SMS command noarm123456 to the tracker device Response The device will reply noarm ok Shacking Alarm The device has built in vibration sensor The vibration sensor has three shacking alarm levels high medium and low Enable Shacking Alarm Command Send command SMS shake password space le
10. ame 22 IP and Port Setup for GPRS network access Command Send command ip password space IP Address space Port Number to set the IP address and TCP port of the PC monitoring software server to be connected Response The device will reply ip ok with IP Address Port Number Another possible error response ip error for already connected to server To reset the IP address and TCP port Send command noip pswd Example Send SMS command ip123456 180 210 239 91 9000 to the tracker device If succeeded ip OK with 180 210 239 91 9000 is returned by the device in SMS 123456 is default password 180 210 239 91 is IP 9000 is port 23 Connect to the Monitor Server GPRS tracking mode login Command Send SMS command gprs password to order the device enter the GPRS tracking mode and connect to the monitor server The device s default working mode is the SMS control mode This command is to start connecting to the PC monitoring software server and order the device change to the GPRS tracking or called PC monitoring mode It requires both the APN and the IP address TCP port configured already Example Send SMS command gprs123456 to the tracker device Response The device will reply a response SMS gprs ok Attention In this mode the device can receive and response to a SMS command from authorized phones but will not report any alarms to them Possible error responses gprs error
11. e alarm is triggered it will be sent at an interval of 3 minutes and can be stopped when the device receives a command of mask or the device detects the vehicle is engine off Attention If both door alarm and acc alarm are triggered the device will only send acc alarm Move alarm Alarm indication move alarm This alarm is enabled when the device receives command arm or the device receives command move This alarm is disabled when the device receives command noarm or the device receives command nomove When the alarm is enabled it will be triggered when the device detects the devices leaves the place at where the alarm is enabled When the alarm is triggered it will be sent at an interval of 3 minutes and can be stopped when the device receives a command of mask or the device detects the vehicle is back to the original place Attention If both acc alarm and move alarm are triggered the device will only send move alarm Attention This alarm can neither be enabled nor triggered unless the GPS works well receiving signals from more than 3 GPS satellites Geo fence alarm Alarm indication move alarm This alarm is enabled when the device receives command stock This alarm is disabled when the device receives command nostock When the alarm is enabled it will be triggered when the device detects the de
12. e installed for this function If not SD CARD in the device will reply error for SD card unavailable or insufficient SD card memory e The time device is minute the maximum value is 120 The recorded audio file will be AMR format and stored in the SD card directory T tk203b audRec e The recording will stop automatically when the current command execution is finish Stop offline voice recording immediately Command Send SMS to tracker device noaudrec password to stop device offline voice recording immediately Example Send SMS command noaudrec123456 7 IMEI Check Check Tracker Device IMEI number Command Send SMS command imei password to the device Example Send SMS command imeil23456 to the tracker device Response An IMEI number in 15 digits will reply to your cell phone in SMS 8 Timezone Setting Setup a Time zone Command Send SMS command timezone password space zone to set the timezone If no timezone is set the timestamp used in SMS will be in Greenwich Mean Time zone should be times of 0 5 with the value interval 12 0 12 0 Example Send command SMS timezone123456 8 8 is Chinese time zone The tracker device will reply timezone ok with 8 Attention If your country time zone is minus send SMS time zone123456 8 the tracker device will reply timezone ok with 8 9 Geo fence This command is to set an electronical fence If this command has b
13. e no metal obstruction 5 Insert the Temperature and humidity sensors plug into the jack J1 Sensor is Option 6 Ifyou need read data in the SD card or update device firmware connect the USB cable to the mini USB interface Please refer to the firmware instructions in the CD Attentions Please ask the qualified engineers to install the device e Do not install the device when GSM GPS signal is in poor condition e Place the antennas in appropriate positions with good signals O Prevent the device from water and dust 9 Turn on the Tracker Device Turn on the backup battery switch then insert 10 PIN harness into the 10 PIN jack 32 The tracker device will work normally after 3 5 minutes II Tracker Device Operating Mode The device has two operating modes 1 SMS Monitoring Mode SMS monitoring mode is the device s default monitoring mode User could use the authorized telephones as a master control monitor the device by sending SMS text messages We mainly discuss this mode in this manual 2 GPRS Tracking Mode With an Internet connected computer user could also use a professional PC software or service platform to control monitor the device This mode is called the GPRS monitoring mode Before using this mode some related internet parameters should be set firstly through the SMS monitoring mode How to use the GPRS tracking mode is beyond the scope of this manual We only introduce the related GPRS paramet
14. een set an alarm will be reported to user when the device is out of the fence Setup a Geo fence Command The user can send SMS stock password space lat0 long0 space lat1 long1 to the tracker device to set the restricted district lat0 and lon0 indicate the latitude and longitude of the start point the top left corner of the Geo fence respectively and lat1 and lon1 indicate the latitude and longitude of the end point the bottom right corner of the Geo fence respectively Alarm When the terminal moves out of the fence the tracker device will send a SMS stock current Geo info to the authorized telephone numbers in 3 minutes interval repeatedly Example Send a SMS Stock123456 22 11 113 11 25 11 115 11 to the tracker device If the terminal moves out of the fence the tracker device will reply a SMS stockad alarm lat 22 55334 log 113 903418 Attentions O The first latitude longitude is coordinate of the top left corner of the Geo fence while the second latitude amp longitude is the coordinate of the bottom right corner O The alarm will repeat in 3 minutes interval when triggered This command is recommended to set when the device stays immobile in a place e If this command is received when an electronic fence was already set the new fence will replace the old one Cancel a setting Geo fence Command Send SMS nostock password to deactivate this function 10 Moving Alarm Set
15. er setting in the following chapters Ill Basic functions 1 SMS Command Format Attention The in all following commands means there is a blank space here in the short message please do not type a real character on your cell phone SMS is an important communicating way between a user and a device Users could send SMS messages through authorized mobile phones to control and monitor devices Devices could also send messages to the user s authorized mobile phones to reply to the user s instructions report the relevant information of the vehicles or perform one alarm Four Types of SMS messages are supported in this device e SMS Command sent by the master to control the device or change some configuration SMS Response reported by the device as a synchronous response to a SMS command e SMS Notification reported by the device as an asynchronous response to a SMS command e SMS Alarm reported by the device when detecting one alarm or several alarms Attention The device will not give any response to an illegal SMS message SMS Command A SMS command is used by the user to do some control action or change some configuration of the device The command has two common formats as following For a command with parameter s cmd pswd space parameter s for a command without a parameter cmd pswd in which O cmd indicating the name of the command and O pswd indicating the pas
16. he user could monitor the device s environment sound voice After the device enters this state when the users call the device using an authorized telephone the device will no longer hang up the call or reply a short message including the real time latitude and longitude information as usual but connect the call from the phone In this way the user could monitor the device environment sound voice Attention In voice monitoring state the device could receive and response to user s SMS command but could not report alarms actively Example Send SMS monitor123456 the terminal will reply monitor ok Quit Real Time Voice Monitor State Command Send SMS command tracker password to tracker device it will reply tracker ok quit the voice monitor state and go back to normal SMS control mode That means when the user calls the device using an authorized telephone the device will hang up the call and reply a short message including the real time latitude and longitude information as usual Example send SMS tracker123456 the terminal will reply tracker ok 6 Offline Voice Recording Start offline voice recording Command Send SMS audrec password space time to tracker device to setup device sound recording Example Send SMS command audrec123456 20 If succeeded the device will reply audrec ok with 20minute Then it will start to record environment sound voice for 20minutes Attentions e SD Card must b
17. he authorized number at 3 minutes intervals The display of the remaining charge as a percentage of the battery This alarm is always enabled and will be sent at a interval of 3 minutes until the device receives command mask or the external power supply is available or the quantity of electricity of the battery is higher than 20 External power supply cut off alarm Alarm indication power stop alarm When the alarm is enabled it will be triggered when the external power supply is cut off This alarm can be enabled when the device receives command pstop or the device is powered on with the external power supply is on This alarm can be disabled when the device receives command nopstop When the alarm is triggered it will be sent at a interval of 3 minutes and can be stopped when The device receives command mask SOS Alarm indication HELP ME This alarm is used to asking for help to all authorized users It is always enabled and will be triggered when the user presses the SOS button for 3 seconds or the user presses the B button of the remote controller for 3 seconds When the alarm is triggered it will be sent at a interval of 3 minutes and can be stopped when the device receives command nohelp or The device receives command mask Door Alarm Alarm indication door open alarm This alarm is enabled when the device receives command
18. in password to the device it will reply begin ok and initialize all the settings to default factory settings Example Send SMS begin 123456 it will reply begin ok Default password 123456 2 Change Password User could change the default password 123456 to a new one Command Send SMS password old password space new password to the device to change the password Example Send SMS password123456 888888 to the tracker device it will reply password ok with 888888 and change the password Attentions e Be sure to keep the new password in mind you have to upload the firmware to restore the original setting in case of losing the new password O Make sure the new password is in 6 digits Arabic numbers Other characters are not recognized by the device 3 Authorization Authorization phone number is a phone number you used for tracking controlling alarms etc At most 5 phone numbers is allowed to be authorized for the tracker device When an alarm is triggered the device will only sends alarm SMS to the authorized telephone numbers Add masters Add authorization as following two ways O For the first authorization call and track the device successfully for 10 times from a mobile phone the device will set this phone number as an authorized number automatically and reply a SMS add master ok O After the first authorization the other authorized numbers should be set by the fir
19. iren will beep one time DISARM Press B button for 0 5 second the siren will beep two times Press A B together in disarm state for 0 5 second the siren will beep three times siren Silent mode won t be sound after alarm is triggered but tracker device will send alarm SMS to authorized numbers Press A B together in disarm state for 0 5 second again siren will beep four times Siren Quit silent mode will be sound after alarm is triggered And tracker device will also send SMS alarm to authorized numbers Deterrence Long press A button for 3 seconds siren will be sound for 30 seconds one Long press B button for 3 seconds device will send SOS alert to authorized phone numbers IV Alarms An alarm indicates a problem of the device If an alarm is enabled it will be reported immediately at the moment of being triggered If the problem is not solved and the alarm is neither disabled nor masked off the alarm may be reported continuously at an interval of 3 minutes An alarm has a common format as following alarm indication Lat lat Lon lon Speed spd Alt alt timestamp in which alarm indication indicating what this alarm is for There may be more than one alarm indication in one alarm lat indicating the latitude of the place at where the alarm is triggered sent lon indicating the longitude of the place at where the alarm is triggered
20. keVol indicating the vibration level of the sensor Siren Status indicating whether the siren is on with a possible value of on or off and Another possible error response check error for no master set 18 Check The Device s Config Information Command Send command config password to the device to acquire the config information of the device Example Send SMS command config123456 to the tracker device Response The device will reply a response SMS to report the tracker device config information with the following format alaCfg move arm speed val shake val pspt stock opCfg Log relay mst number apn c apn name ip val port val timezone zone timestamp In which alaconfig Alarm config the alarms which have been set already will be displayed in the SMS move If present in the SMS means moving alarm turned on now otherwise this alarm is off now arm If present in the SMS means Arming turned on now speed val If present in the SMS means overspeed alarm turned on shake val If present in the SMS means vibration alarm turned on pspt If present in the SMS means external power supply alarm turned on now stock If present in the SMS means electronic fence alarm turned on now relay If present in the SMS means the relay was cut oil and power LOG If present in the SMS means tracking trace record function enabled now mst Amount of the a
21. l 10 Built in vibration sensor external temperature and humidity sensor be supported 2 Applications This product is widely used for vehicle and other moving objects especially for personal cars company government vehicles taxies and motorcycles 3 Hardware Description The tracker device hardware interface diagram is shown as below Ha w a En an a 01 GPS Antenna connector 03 SIM Card slot Pop up switch 05 Micro SD Card SD slot 07 GSM Antenna connector 09 10Pin Harness J2 11 Remote controller antenna window 4 Accessories 02 04 06 08 Backup battery switch Mini USB slot Power GSM GPS LED indicator Monitor jack J3 Temperature sensor jack J1 eo E i Te ll 12V 40A or 24V 40A Relay z F according to vehicles Remote control 15 meters control o Temperature and humidity Option sensor Specifications Content specifications SIZE 83 54 26mm Weight 120g Network GSM GPRS Locating Method A GPS GPS GPRS GSM Band 850 900 1800 1900 MHz GSM Sensitivity 105dBm 6 GPS Module UBLOX GPS Sensitivity 159dBm GPS Accuracy 5m i Cold start up time 27s GPS Start up time Warm start up time 27s Antenna opensky y Hot start up time 1s Voltage of power system 12 V 24V Backup battery Chargeable 3 7V 800mAh Li ion battery Storage Temp 40 C to 85 C
22. n Lat lat Lon lon Speed spd Alt alt timestamp in which O alarm indication indicating what alarm it is and lat indicating the latitude of the place where the alarm is triggered and lon indicating the longitude of the place where the alarm is triggered and spd indicating the speed when the alarm is triggered and alt indicating the height of the place where the alarm is triggered and O timestamp indicating the time point at which this alarm is triggered Please refer to next chapters for further details SMS Command List In the following command list O All commands are case insensitive Command Format Command Example Command Functionality reply begin pswd begin123456 To initialize the configuration and reset the device passwd pswd space newP swd passwd123456 888888 To change the password Old password 123456 New password 234567 admin pswd space adminNum admin123456 13800138000 To add a new master telephone number 13800138000 Noadmin pswd noadmin123456 To delete a master telephone space adminNum 13800138000 number 13800138000 monitor pswd monitor123456 To start voice monitoring To switch to the SMS Monitor tracker pswd tracker123456 mode gprs pswd gprs123456 To switch to GPRS Tracking mode tn pswd space interval tn123456 120 20 space To start locati
23. ng tn123456 20 repeats notn pswd notn123456 To stop locating stock pswd stock123456 12 3456871 space lat0 lon0 lat1 lo 118 3456123 12 3668121 To set an electronic fence nl 118 6012345 nostock pswd nostock123456 To delete the electronic fence move pswd move123456 To enable the moving alarm nomove pswd nomove123456 To disable the moving alarm speed pswd space spd speed123456 60 To enable the over speed alarm nospeed pswd nospeed123456 To disable the over speed alarm To mask off the currently generated nohelp pswd nohelp123456 SOS request To cut off the power supply of the stop pswd stop123456 car To resume the power supply of the resume pswd resume123456 car arm pswd arm123456 To enable the safe guard noarm pswd noarm123456 To disable the safe guard check pswd check 123456 To get the current status of the device imei pswd ime1123456 To get the IMEI of the device timezone pswd space zone timezone123456 8 To set the timezone apn pswd apnName apnU sr apnPswd apn123456 cmnet To set the APN ip pswd space ipAddr ip 123456 192 168 100 1 To set the IP address and TCP port space tcpPort 9000 of the PC Monitoring tool To reset the IP address and the TCP noip pswd noip 123456 port of the PC Moni
24. nse The device will reply Speed OK with 80km h to indicate overspeed alarm setting successfully Another possible error response is speed error for no master set Alarm When this command setting successfully an overspeed alarm will be reported if the vehicle s speed exceeds the speed limit When the target moves exceeding 80km h the tracker device will send alarm SMS speed alarm 080 Geo info to the authorized telephone numbers Cancel overspeed alarm Command Send SMS nospeed password to deactivate the overspeed alarm Example Send SMS command nospeed123456 to the tracker device 12 Cut off the Oil and Power System Setup Cut The Car Oil Power Command Send SMS command stop password to the tracker device This command is to cut off the power supply of the car but it will not take effect if the device s speed is higher than 60 km h for safety guarantee Example Send SMS command stop123456 to the tracker device Response The device will reply Stop ok to your cell phone and stop your car engine at the same time It will remain the immobile state until receiving the next resume password command Another possible error response is stop error for no master set 13 Resume the Oil and Power System Resume The Car Oil Power Command Send SMS command resume password to the tracker device 14 15 16 This command is to resume the power supply of the car Example Send
25. rigger or negative trigger When the door trigger is negative trigger Harness Door pin connect to the car battery Power Harness Door pin connects to the door control circuit When the door trigger is positive trigger Harness Door pin connect to the door control circuit Harness Door pin connects to the car battery ground c Connect the white wire to the vehicle Car ACC ignition switch d Placed the automotive relay socket to the proper position inside the hood of the car Find the car s original engine cable and cut it off Connect the engine side of the original cable to the thick red cable of the relay socket Connect the oil pump side of the original cable to the thick yellow cable of the relay socket Attentions e The white thin cable of the relay socket should be connected to the car supply power and we have connected the thin white cable to the red thick cable already For original vehicle usage that s ok We have connected the yellow cable of the 10 PIN harness to the automotive relay already e The joints must have good insulation protection e Connect the orange wire to the siren you bought Siren is Option 3 Put the Reset button and SOS button to the place where the driver could touch conveniently 4 Connect the GPS antenna and GSM antenna to the corresponding connectors Find appropriate places to fix the two antennas and make sure they receive signals well The GPS Antenna must be exposed to the air and hav
26. s please confirm that the device is power off O Maximum capacity of SD card is up to 32GB O In order to read the data in SD card you can connect the device to the computer with the USB cable You can also remove the SD card when the device is power off and use a SD card reader 8 Install the device into the vehicle The hardware interface with the car external harness is shown as below the car engine and oil line Unit line oil pump A OX Car line to pump sde yellow i to engine side Schematic ed a Cut white 12v 1989 10 INOIT door trigger white white black 508 red black reset button battery switch 4 door trigger Diagram of connection 1 Put the device into the proper position inside the car Attentions Identify the trigger type of your car Positive or negative trigger For vehicle with positive trigger Please keep the device isolated from the vehicle frame Otherwise the device and the battery of your car may be damaged 2 Find the 10 PIN harness and connect wires with the original car circuits as following step Please refer to connection diagram as below Reference to the diagram the installation procedure as following a Connect POWER amp GND wire to car battery The red wire is connected to positive terminal of car battery the black wire is connected to negative terminal of car battery b Identify the type of the door trigger positive t
27. se E ceee cee E ee stead E EE ar aE eee e EE E EEES Bi Shock Sensor il aida Gs AGG E y ceed OPA o ietepasssdateseaecects duns faueters EE E T Mao Bi Geo fencesalarimisies seeds ceiees i vee ene Re 9 Speed O ots eee ece sees 10 Lack SDcard space da e 11 Power Off Alarm V LED indicator status VIOperation SULE tad tistid dd dida estic ld VI Common Faults amp Solutions I Function Introduction This tracker is a new product based on GSM GPRS network and GPS satellite positioning system It has multiple functions such as positioning tracking monitoring and alarms for security User can easily track and monitor vehicles or other moving targets by mobile phone or Internet connected computer 1 Main Features 1 2 3 4 5 6 7 8 9 Support A GPS GPS base station positioning Support SMS GPRS Internet Network data transfer GPRS Internet instructions in CD enclosed Support point to point point to group group to group monitoring Support single positioning and continuous location tracking Support voice monitoring and recording SD card required Supports historical traveling locus uploading SD card required Support Vehicle Anti theft alarming Remote control setup Cancel Support electronic fence alarm door open alarm ACC alarm moving alarm speeding alarm SOS alarm and other kinds of emergency alarms Support alarm for equipment malicious remova
28. st authorized phone Sending a SMS admin password space mobile phone number to set an authorized number if the number is successfully authorized the device will reply admin OK with authorized number Example Send SMS admin123456 13800138000 to the tracker device it will reply admin ok and the number13800138000 will be set up as a new authorized number If the user needs to track a target device when it s in another country you must add your own country code before the cell phone number when executing the authorization Example send SMS admin123456 008613800138000 to the device Here 0086 is China s country code Delete authorization Command Send SMS noadmin password authorized number to delete the authorized number Example Send SMS noadmin123456 13800138000 to delete the authorized number 13800138000 4 Locating Single Locating If none authorized number has been set the device will reply a SMS including the position of latitude and longitude when any number dial up it Once the first authorized number has been set successfully the device will only reply SMS to the authorized numbers Dialing the tracker device from an authorized number the device will hang up your calling and then send back a SMS to the authorized number including the real time latitude and longitude information as following Lat 40 0556670 Lon 116 3240700 A en ee ree ee t t tat t tion Cellld e54 Lac 104a e
29. sword and O parameter s indicating the parameter s taken by the command For a command cmd and pswd are indispensable but the number of parameters is dependent on the command The default password is 123456 SMS response Upon the receipt of a SMS command the device will respond a synchronous response The SMS response has a common format as following command result timestamp In which O command indicating the command sent by the user and O result indicating the result of the command implementation and O timestamp indicating the time point of the implementation And the result may be e ok if the command is executed or O password error if the given password is incorrect or e format error if the given parameter is incorrect or e error followed by a detailed description of the error if the device failed to execute the command SMS Notification Besides the synchronous response the device may respond asynchronous notifications and tell the final execution result of a command The asynchronous notifications have a common format as following notification timestamp In which O notification indicating the content of this notification and O timestamp indicating the time point at which the notification was sent SMS Alarm A SMS alarm is used to tell the master some abnormal status of the device The alarms have a common format as following alarm indicaio
30. tallation and operation Pay attention to the product s working voltage range Otherwise it won t work properly or even worse might be destroyed VII Common Faults amp Solutions 1 Check whether power ground wires are correctly connected Startup Fail 2 Turn off the tracker device and remove harness 3 Turn on the tracker 1 Check whether the GSM antenna is correctly connected Call Fail 2 Check whether SIM card is correctly inserted 3 Check up the power supply condition It s usually happened when an unauthorized number dials up this Hang up Fail device in steady of authorized numbers Please initialize the device and set up authorized numbers again Monitor Fail Check whether authorized numbers have been set up correctly Location report always in Check whether the GPS antenna is correctly connected digits of zeros Check whether the GPS antenna is put in right place
31. toring tool audrec pswd audrec123456 10 To start audio recording space period noaudrec pswd noaudrec123456 To stop audio recording nospeaker pswd nospeaker123456 To disable the speaker pstop pswd pstop123456 To enable the power stop alarm nopstop pswd nopstop123456 To disable the power stop alarm shake pswd level shake123456 To enable the shaking alarm To mask off the currently generated Mask pswd mask123456 alarm s To start logging the track of the log pswd log123456 device To stop logging the track of the nolog pswd nolog123456 device address pswd address123456 To get the address of the device Silent pswd Silent123456 To stop the buzzer humget pswd humget123456 Get the Humidity humset pswd humset123456 20 Set Humidity alarm space humVal Tempget pswd tempget123456 Get the Temperature Tempget pswd tempset123456 20 Set Temperature alarm space humVal Loud pswd Loud123456 To start the buzzer Config pswd Config123456 Check device setup parameter 3 SMS Command Response Notification Alarm explanation by Functions To explain the usage of the SMS message this chapter will show how to use the above short message functions one by one Attention No quotation marks when sending all the SMS 1 Initialization User should initialize the device before using it This command is to set all configurations to the default values Command Send the command SMS beg
32. tracker to force the siren silent Example Send SMS command silent123456 to the tracker device Response The tracker device will reply silent ok and force the siren silent In this situation if any type of alarm is triggered the buzzer will not tweet but the tracker device will still send related alarm SMS to the authorized phone number Exit the Silent State Command Send command loud password to the tracker device to force the siren exit the silent state Example Send SMS command loud123456 to the tracker device Response The tracker device will reply loud ok and exit the silent state When any type of alarm is triggered the siren will tweet and at the same time tracker device will send alarm SMS to the authorized phone number 4 Tracker Device Hardware Reset Reset button Press the reset button for 3 seconds the tracker device will be hardware reset 5 Function Of Remote Controller User can control the tracker device by remote controller Electronic security and alarm functions are supported Please refer to the following form ARM set cancel by remote controller Click the A button on the remote controller the vehicle will enter ARM status alarm status the buzzer will sound once no SMS reply Click the B key on the remote controller the vehicle will enter the non ARM status non alarm status the buzzer will sound twice SMS reply States Instructions ARM Press A button for 0 5 second the s
33. up moving alarm Command When the vehicle stays immobile in a place and the engine is off the user could send a SMS move password to the tracker device to setup a moving alarm The command can only take effect only when the car engine is off and the device can get the precise latitude and longitude of the current position Example Send SMS command move123456 to the tracker device Responses The device will reply move OK to indicate move alarm setting successfully Other possible error responses are move error for no master set move error for engine is on move error for current position is not accurate Alarm In case of such a movement the default distance is 200m the device will send an alarm SMS Move current Geo info to the authorized numbers in 3 minutes interval repeatedly Cancel moving alarm Command Send SMS nomove password to deactivate the movement alarm Example Send SMS command nomove123456 to the tracker device 11 Overspeed Alarm Setup overspeed alarm Command Send SMS speed password space speed limit value to the device to set the overspeed alarm After the setup the speed alarm will be triggered and reported to the user if the vehicle s speed exceeds the speed limit Speed limit in command is an integer value 60 360 with the device km h Example Send SMS speed123456 080 to the device to set the speed limit to 80km h Respo
34. us Example Send SMS command tempget123456 to the tracker device get the drivereply temp is 25 Get the Humidity Command Send command humget password to acquire the Humidity of the device Response The device will reply a SMS including the Humidity Attention Humidity value expressed as a percentage Example Send SMS command humget123456 to the tracker device get the drivereply hum is 25 Set the Temperature and Humidity Alarm Temperature alarm set Command Send command tempset pswd space humVal to set the Temperature alarm of the device Response The device will reply a SMS Example send command tempset123456 25 to tracker device Temperature alarm set Command Send command humset pswd humVal to set the Humidity and Temperature alarm of the device Response The device will reply a SMS Example send command humset123456 25 to tracker device Get Street Address Command Send command address password to acquire the address of the device Example Send SMS command address123456 to the tracker device Response The device will reply a SMS including the current street address Attention If the user wants to be informed of the specific location of your device now you must set the APN first Example get the drive reply address Anningzhuang Road Haidian Beijing China 28 Siren Setup Force Siren Silent Command Send command silent password to the
35. uthorized phone numbers 1p IP address port port settings timezone timezone date and time 19 20 Example Send config 123456 to the device it may reply alaCfg mv arm spd 120 shk 2 opCfg log relay mst 1 apn cmnet 1p 222 129 50 210 port 9994 timez 8 0 2012 12 20 14 36 53 External power supply cut off alarm Enable External Alarm power alarm Command Send command pstop pswd to the device This command is to enable the alarm if the 12V 24V external power supply from the battery of the vehicle is cut off by someone This alarm function is disabled by default and should be enabled by user if necessary Example Send command pstop123456 to tracker device set External power supply cut off alarm Response The device will reply a response SMS pstop ok Alarm If this alarm function enabled when the external power supply was illegally cut off the tracker device will report an alarm SMS power cut alarm Disable External Alarm power alarm Command Send command nopstop password to the device Example Send SMS command nopstop123456 to the tracker device Response The device will reply a response SMS nopstop ok SOS Alarm Long Press the SOS button of the device for 3 seconds or press B button on the remote controller for 3 seconds the tracker device will send SMS help me lat long to all the authorized numbers in 3 minutes interval repeatedly The message
36. vel to the tracker device to enable the Shacking Alarm The level could be 1 2 3 refers to high medium low and the default level is 2 Response The device will reply shake ok with 2 and open the shacking alarm Example Send SMS shake123456 2 to the device to open shacking alarm and set vibration level to Medium Disable Shacking Alarm Command Send SMS shake password 0 to the tracker device to disable the Shacking Alarm Example Send SMS command shake123456 0 to the tracker device Response The device will reply shake ok with 0 and disable the shacking alarm Tracking Trace Recording To realize this function must be installed SD card Enable tracking trace recording Command Send SMS log password to the device to start tracking trace recording The tracking trace record will be stored in the SD card in KML format Response The device will reply log ok and start to record the tracking trace of the device in the SD card Other possible error responses are log error for no master set log error for sd log unavailable or is already in logging Example Send SMS log123456 to the device if success the device will reply log ok and start to store the tracking trace into the SD card directory T tk203b trace_kml With this feature user could observe the tracking trace of the vehicle when necessary Disable tracking trace recording Command Send SMS nolog password to the de
37. vice This command will stop the recording for the tracking trace Example Send SMS command nolog123456 to the tracker device Response The device will reply nolog ok to stop the recording Other possible error responses nolog error for no master set nolog error for no sd log to stop Example Send SMS nolog 123456 to cancel the track record 17 Check the Device s Working Status Command Send command check password to the device This command is to acquire the status of the device Example Send check123456 to the device Response The device will reply a response SMS to report the tracker device status with the following format Mode mode GpsNum gpsNum Bat batVol Sd sdVol Power powerSupplyStatus Acc accStatus Door doorStatus Relay relayStatus Shake shake Vol Siren siren status In which mode indicating the current monitoring mode and gpsNum indicating the current number of the available GPS satellites and batVol indicating the remaining volume of the backup battery in percentage and sdVol indicating the remaining volume of the SD card in MB and accStatus indicating whether the engine is on with a possible value of on or off and doorStatus indicating whether the door is open with a possible value of open or closed relayStatus indicating whether the relay is on with a possible value of on or off and sha
38. vices is out of the geo fence When the alarm is triggered it will be sent at an interval of 3 minutes and can be stopped when the device receives a command of mask or the devices returns to the range of the geo fence Speed Alarm Alarm indication speed alarm This alarm is enabled when the device receives command speed This alarm is disabled when the device receives command nospeed When the alarm is enabled it will be triggered when the device is at a speed higher than the present value When the alarm is triggered it will be sent at an interval of 3 minutes and can be stopped when the device receives a command of mask or the device is at a speed lower than the present value Attention If both move alarm and speed alarm are triggered the device will only send speed alarm 10 Lack SD card space Alarm Alarm indication SD card insufficient alarm remains vol MB This alarm is always enabled if the SD card is available and will be triggered when the SD card remains less than 20MB When the alarm is triggered it will be sent at an interval of 3 minutes and can be stopped when the device receives a command of mask or the SD card remains more than 20MB Attention The device support to communicate with a PC via a USB connection with which the user can do some operations on the SD card when necessary such as file copy file
39. will be send repeatedly until any authorized number reply a SMS no help to the tracker device Example Send SMS command nohelp123456 to the tracker device 21 APN setting for GPRS network access The setting of APN Access Point Name is different from country to country The detail information of APN is beyond the scope of this manual Please contact your local GPRS network operator for more information about your local APN Command 1 Send command apn password space apnname space username space password to the device to set the APN 2 If the local APN setting need no user name and password send command apn password apnname Response The device will reply a response SMS apn ok with apnName apnUser apn pass Ifuser receive the error response SMS error for having already been connecting or connected to a Server Please check carefully whether the settings APN username password correct or not Example send command APN123456 general t mobile uk user pass to the device to set a UK provider T Mobile s APN The tracker device will reply a SMS apn ok with general t mobile uk user pass Note 123456 is terminal the password general t mobile uk is the UK provider T Mobile APN The user is the APN username pass is the APN Password In China for the APN setting does not require user name and password user could send SMS apn123456 cmnet to device it will reply apn ok Note cmnet is a Chinese APN n
Download Pdf Manuals
Related Search