ADEMCO 5828/5828V - Gargoyle Security Inc.
Contents
1. B C D that may be programmed to execute the commands shown below NOTE The Function Key Select setting in Step 6 of the INSTALLER PROGRAMMING procedure above determines the operation of the Special Function keys A B C and D as follows STEP ACTION DISPLAY If you select 0 career meet ossage So Enter the two digit house code 01 31 and the 2 Fu ction Key Function To Control Press to continue digit house A 1 k Alarm zone 95 code B Alarm zone 99 2 Press 2 System Type Alternately C 3 Alarm zone 96 Press 1 for VISTA or 2 for LYNX flashes t2 D Not used for panic alarms 2 default and 2 NOTE Do NOT use the 5828V for silent panic operation Press to continue because the keypad itself is not silent If you select 1 normally used on LYNX controls Function Key Function A Off B Arms AWAY C Arms STAY D For future use MEMO MESSAGE CENTER The MESSAGE CENTER table that follows explains what can be done using the message center of the 5828V and the keys to press to enable each function NOTE Allow any status annunciation to complete before starting to record a message MESSAGE CENTER LYNX TO PRESS Record a message 1 Stop recording before end of 20 seconds 1 Playback a message 3 Adjust message p2. AA batteries The 5828 and 5828V keypads can also be powered from an optional Power Pack Desktop Mounting Kit See detailed specifications for the Kit below It is recommended that three AA batteries be installed as a backup power source when using the Power Pack Desktop Mounting Kit 5828 5828V SPECIFICATIONS Physical 6 1 4 W x 4 3 4 H x 1 3 8 D 159mm x 121mm x 35mm Frequency of 345 MHz Operation Batteries 3 1 5 Volt AA Alkaline Power Pack Dect Mounting Kit OVAG input 8 9 Vol Regulated DG optional put LCD Display Fixed Word Liquid Crystal Sounder Speaker SUPERVISION A 5828 5828V keypad low battery condition will be displayed as BAT on Zone 00 until the battery drops below a minimum level and the display goes blank NOTE When programming zone descriptors in the panel you must select from words supported by both the 5828V shown in Table 1 below and words supported by the control panel If you use any other words the 5828V will not annunciate them Refer to the control panel s Installation and Setup Guide for specific instructions on programming zone descriptors TABLE 1 ZONE DESCRIPTORS ALARM DEN FOUR MEDICAL POOL STORAGE ATTIC DETECTOR FRONT MESSAGE READY SYSTEM AWAY DINING GARAGE MOTION ROOM TEN BABY DOOR GUN NINE SECOND THIRD BACK EIGHT INSIDE NOT SEVEN THREE BASEMENT EMERGENCY
3. Honeywell KO020V1 7 04 Rev A ADEMCO 5828 5828V Wireless Bidirectional Fixed Word Keypads INSTALLATION AND SETUP GUIDE GENERAL INFORMATION The 5828 and 5828V are wireless bidirectional fixed word nonaddressable keypads that are used in conjunction with LYNX Series control panels or VISTA Series control panels that are using a 6160RF Keypad transceiver Both keypads provide e Four programmable special function keys e Wall mount plate allowing easy removal of the keypad and battery replacement e Optional Desktop mount AC adapter kit ADEMCO P N 5828DM e Battery powered with 3 AA batteries In addition to the above features the 5828V keypad provides the following e Memo Message center e Voice Response system status zone information and alarms with zone information e Stored Message LED indication e Built in microphone and speaker NOTES e The 5828 5828V cannot be used as a primary keypad to program and or test any security system All systems require a hard wired keypad to do so Once programmed and tested the 5828 5828V can be used to initiate all other keypad functions in both the VISTA and LYNX series systems However you must have at least one hard wired keypad permanently connected on VISTA series control panels 5828 00 001 VO o mic o MESSAGE 1o 2m B sm B TdT RECORD VOLUME PLAY READY lt gt A mx 5 rsr Gavea
4. INSTANT NOW SHED TWO BATHROOM EXIT KITCHEN OFFICE SHOP UPSTAIRS BEDROOM FAULT LAUNDRY ONE SIDE UTILITY BYPASSED FIRE LIBRARY OPEN SIX WINDOW CHECK FIRST LIVING PANIC SLIDING YARD CHIME FIVE MAIN PATIO SMOKE ZERO CLOSED FLOOR MASTER POLICE STAY ZONE These Descriptors are available with VISTA Series control panels ONLY This Descriptor is available with Lynx Series control panels ONLY FCC STATEMENT FCC ID CFS8DL5828 CANADA 1748A 5828 This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation FEDERAL COMMUNICATIONS COMMISSION FCC Part 15 STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use The FCC requires the following statement for your information This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarante
5. USED Honeywell 165 Eileen Way Syosset New York 11791 Copyright 2004 Honeywell International Inc www honeywell com security K0020V1 7 04 Rev A
6. ce enable disable Alternately 5828V Press 0 to disable flashes t4 only Press 1 to enable and 0 or 1 1 default Press to continue 5 Press 5 Wireless Protocol Alternately Press 1 for LYNX models flashes t5 Press 2 for LYNXR LYNXREN or and 1 or 2 VISTA 2 default Press to continue 6 Press 6 Function Key Select Alternately Press 0 for Panic Key flashes t6 Press 1 for Single button arming and 0 or 1 NOTE The programming here should match the programming of the control panel to simplify end user operation 1 default Press to continue 7 Press 7 Restore Defaults Displays Press 1 to restore factory settings EE Press Exit programming mode Exiting Programming Mode You can exit programming mode by pressing the key whenever the small 00 and are alternately displayed Programming or Changing a User Code Required if using Quick Arm function on Lynx or VISTA Enter user program mode by pressing the 7 and 9 keys at the same time until the display flashes double dashes Enter the desired 4 digit user code that matches a user code programmed in the control panel There will be no display of the user code entered Press the key to place the 4 digit code in memory and exit the user program mode SPECIAL FUNCTION KEYS As shown in the figures on page 1 each keypad contains four Special Function keys A
7. e that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e f using an indoor antenna have a quality outdoor antenna installed e Reorient the receiving antenna until interference is reduced or eliminated e Move the radio or television receiver away from the receiver control e Move the antenna leads away from any wire runs to the receiver control e Plug the receiver control into a different outlet so that it and the radio or television receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user or installer may find the following booklet prepared by the Federal Communications Commission helpful Interference Handbook This booklet is available from the U S Government Printing Office Washington DC 20402 The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User s Manual Unauthorized changes or modifications could void the user s authority to operate the equipment FOR WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE ALARM SYSTEM REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS
8. layback volume 42437 or 6l Mute keypad status announcements 24 1 Restore keypad status announcements 4 24 3T or 6l MESSAGE CENTER VISTA TO PRESS Record a message 0 1 Stop recording before end of 20 seconds 1 Playback a message 0 3 Adjust message playback volume 4 04 2 3T or 6l Mute keypad status announcements 0 2 1 Restore keypad status announcements 04 2 3T or 6L New message indication When the keypad is activated in battery powered mode and a message had been recorded the red message LED will blink until the keypad turns off or the message is played back When powered by AC if a message had been recorded the red message LED will blink continuously until the stored message has been played back NOTE If the word MESSAGE is annunciated on the 5828V keypad it means that there is a message waiting at the control panel which can only be retrieved using the LYNX keypad To delete a message Record a new message to override the old one Muting system status announcements has NO affect on the message recording or playback capability If volume is adjusted 37 or 61 when a message is played back and the user still wants system status announcements to be muted the user must again mute system status announcements 2 1 for LYNX or 0 2 1 for VISTA POWER CONNECTIONS In a typical configuration the 5828 and 5828V keypads are powered by 3
9. phic below batt_case 001 VO Battery Compartment Reattach the keypad to its mounting plate by aligning the four mounting holes in the keypad case back with the four mounting clips on the mounting plate Lower the keypad onto the clips Anticipated battery life is 1 5 years PROGRAMMING The following two items must be programmed into the keypad by the installer House ID Code Step 1 in Installer Programming mode System Type Step 2 in Installer Programming mode The same House ID Code must also be programmed in the control panel Programming a different House ID will disable communication Installer Programming Enter the program mode by pressing the 1 and 3 keys simultaneously for five 5 seconds The DISPLAY alternately flashes small 00 and two dashes NOTES e Entering a value other than one specified in the following steps may cause unpredictable results If the unit times out before you have pressed the star key to save a programmed value you will need to re enter the Programming mode and reprogram the option 3 Press 3 Exit Delay Alternately Press 0 9 in 15 second increments flashes t3 Example If you press 3 exit delay and value would be 3 times 15 seconds for a total selected of 45 seconds NOTE The Exit Delay programmed here should match the Exit Delay programmed in the control panel 0 default Press to continue 4 Press 4 Voi
10. ss ee ce Z ww 8 cove Qonme 1 reor STATUS VOICE FUNCTION 5828V 00 002 VO 5828V Keypad with Front Cover Removed Operation See NOTE below 1 Battery Powered Operation When powered by battery the keypads activate when any key is pressed When the key is pressed the keypad sends a status request to the control The keypad displays and or annunciates the present system status transmitted by the system 2 AC Powered Operation When powered by AC the keypad remains active at all times Any change in system status will cause the display to automatically turn on if blank and display annunciate the new status If AC power is lost the keypad will revert to battery powered operation until AC power is restored and a new status request is made NOTE Whether the unit is powered by battery or AC the 5828 5828V may take up to 5 seconds to display and or annunciate the new status after pressing the key WALL MOUNTING Before mounting the 5828 amp 5828V permanently determine a good RF location as follows e Ifinterfacing to a LYNX panel try communicating with the panel from different locations e If interfacing to a VISTA panel perform a Go No Go test from the panel Refer to the Go No Go test mode in the Installation and Setup Guide for the panel Avoid mounting locations on or near large metal objects since these can decrease the transmi
11. ssion range or block transmissions e Secure the mounting plate to the wall using proper sized hardware through the six mounting holes e Route the wires from the optional power pack through the wire guides on the back of the keypad and into the hole in the back of the keypad e Plug the AC adaptor connector into the keypad s DC input connector e Position the keypad over the mounting plate and slide down engaging the four retaining clips on the plate with the receptacles on the keypad DESKTOP MOUNTING For full portability the keypad may be placed in any conve nient RF suitable location and operated in its battery powered mode or near an AC outlet to be powered by the optional Power Pack Desktop Mounting Kit ADEMCO P N 5828DM BATTERY INSTALLATION OR REPLACEMENT CAUTION Remove the AC DC power connector from the keypad if applicable before attempting to install or replace the batteries Separate the keypad from its mounting plate by sliding the keypad up and away from the mounting plate Open the battery compartment door to expose the batteries Install or replace the 3 1 5 Volt AA batteries in the battery compartment When necessary always replace all three batteries at once to ensure normal operation of the keypad over the anticipated battery lifetime Make sure that battery positive and negative terminals are properly oriented with the battery spring clip connections Refer to battery placement gra
Download Pdf Manuals
Related Search