RTS Electronic Target System Operating and User`s Manual
Contents
1. M RTS Ltd RTS Reactive Target System RTS Electronic Target System Operating and User s Manual RTS Ltd 4152 Georgia Ave Palo Alto CA 94306 408 9 TARGET RTS Ltd Introduction RTS Reactive Target System introduces a significant technological leap in erecting and managing wireless electronic shooting ranges It provides accurate counting of hits in indoor and outdoor shooting ranges both for combat trainees and private individuals RTS represents a revolutionary approach in e Totally eliminating the need to move from the fire line to the target in order to check hits e Significantly increasing shooting range safety e Time saving up to 50 RTS Electronic Target Systems Components Self sealing Reactive Target Torso in a choice of 6 colors Black Red Green Blue Yellow amp White Each torso target can absorb several thousand hits even from point zero before wearing out Reactive Target Poll 0 Reactive Target Base Sy RTS Numerator controls up to 9 targets RTS Remote control RTS Transmitter RTS Sensors The following accessories are not included and can be purchased e Target s disc numbers e Smart Joints e Plastic image bags for torsos e Carry bags RTS Ltd 4152 Georgia Ave Palo Alto CA 94306 408 9 TARGET RTS Ltd RTS Enumerator Setup 1 Open lid at the back of the monitor and insert 6 AA batteries as indicated and close the lid Position the monitor2. close to the firing line Push up the left switch on monitor until the indicator S 29 blinks for one second Push down the right switch on the monitor until LN Learn lights up Wait until the message ER light up which indicates that all previous records were erased Transmitter and Sensor Setup 1 5 Place RTS Target Base on the ground making sure it is stable with captions facing the firing line Place the trunk of the target into the appropriate socket on the base and attach the target torso to the upper part of the column You can also place the bottom push the column into a joint and then push it into the joint round socket in the base for a nock over target Use the rubber band which is included or any other adhesive tape to attach the sensor disc to the target column about 2 inches above base facing the firing line Connect the sensor s wire to the transmitter and make sure that it is properly connected The transmitter s switch has 3 positions Middle normal sensitivity Left high sensitivity Right low sensitivity Insert transmitter into its socket in the base aerial pointed up Repeat for additional targets up to 9 targets RTS Ltd 4152 Georgia Ave Palo Alto CA 94306 408 9 TARGET Base Remote control congruity 1 Press the RTS Numerator s right button until LN is visible 2 Press several times on any remote control button until R 1 is visible 3 Repeat procedure for up to 3 remote contro
3. ivity In case of over score move sensitivity switch towards the green connector to decrease sensitivity e All system components can be easily mobilized e Effective distance from target to monitor up to 200 meters depending on the conditions of the area Range can be increased by raising the transmitter higher up from ground level e Closest effective firing range 5 meters for pistol 10 meters for rifle e Firing from a closer range can cause over score in a near target due to the blast RTS Ltd 4152 Georgia Ave Palo Alto CA 94306 408 9 TARGET
4. ls to be used simultaneously Target Numerator Coordination 1 Press the Numerator s right switch until LN appears 2 Hitthe RTS Reactive Target Torso with a metallic object or shoot one bullet at it T1 Target No 1 appears on the monitor ff 3 Repeat procedure for up to 9 targets to be used simultaneously Operating the Remote Control 1 Button 1 upper left corner turns Monitor On Off 2 Button 2 upper right corner rolls the target numbers forwards 3 Button 3 bottom left corner erases score of target on the display mA 4 Button 4 bottom right corner rolls back to the targets on the Gal monitor 5 Pressing buttons 1 and 3 simultaneously will erase score on the gt displayed target RTS Ltd 4152 Georgia Ave Palo Alto CA 94306 408 9 TARGET RTS Ltd Numerator Incorrect scoring Sensor amp No signal Transmitter Sensor amp Transmitter Transmitter Sensitivity Specifications Check that the batteries are correctly inserted Check that the batteries are fully charged and change if necessary Check the transmitter s range limit Try to raise the transmitter s elevation from the ground Replace batteries Insert batteries Check connection sensor transmitter Check if sensor is intact Change sensor Start by placing selector sensitivity switch on default middle position In case of low score move sensitivity switch away from the green connector to increase sensit
Download Pdf Manuals
Related Search