USER MANUAL - Prostage AS
Contents
1. Important If a connection is done with a un balanced line and pin 3 on the XLR is not connected to ground a 6 dB loss occurs in the line and only a quarter of the amplifier power is produced The two channel amplifier models provides for each channel a female XLR Connector Signal Input parallelled to a male XLR to daisy chain several amplifiers with the same signal line LINK O Balanced Unbalanced wiring 2 E 4 Wiring 1 Gnd O 1 Gnd 2 Signal O 2 Signal 3 Signal a 3 Gnd 3 INSTALLATION 10 CUN pro audio 3 2 Configuration The amplifier has an ensemble of minidips on the back panel which allow for the following configurations the highpass subsonic filter the ICL deactivation and the bridge mode All these configurations can be cross set in any way independently from the others The basic configuration possibilities are as follows Standard Configuration the amplifier works without high pass subsonic filter Clip Limiter ICL enabled and no Bridge mode B On 501 OT or E SUH Of OF 51130 On Bridge Or ICL IEL Sub ponannnn m o Sub 30Hz rn g q SUD Sub sonic Filter Enabled the amplifier works with high pass subsonic filter 30Hz in this case Clip Limiter ICL enabled and no Bridge mode L Of COE lon Sub30Hz O 5 Sub On ED Of Bridge On Of CL Of Ca Bridge Mode e On 50H IG Sub 20H E Su2. B 230V 50Hz 483 x 89 x 310 8 5 Kg SX 6002 4 x 620 W 4 x 1000 W 4 x 1440 W 2 x 2000 W 2 x 2880 W 4 x 1280 W 4 x 2080 W 0 05 3 5 1 8 0 9 V 116 dB 26 32 38 dB 20 20K Hz 15dB gt 500 20 500Hz gt 75 dB 230V 50Hz 483 x 89 x 310 8 6 Kg LUN Technical Specifications SX 2200 2 x 630 W 2 x 1100 W 2x 1570 W 2200 W 3140 W 2 x 1240 W 2 x 2060 W 0 05 3 6 1 8 0 9 V 115 dB 26 32 38 dB 20 20K Hz 15dB gt 500 20 500Hz gt 75 dB 230V 50Hz 483 x 89 x 310 8 5 Kg SX 1504 4 x 1015 W 4 x 1480 W 2 x 2960 W 4 x 2110 W 0 05 5 0 2 5 1 3 V 118 dB 26 32 38 dB 20 20K Hz 15dB gt 500 20 500Hz gt 75 dB 230V 50Hz 483 x 89 x 310 8 6 Kg LUNA 2 Hardware Controls 2 1 Front Panel See Figure A 1 Signal attenuation level control knobs Permit independent control of each channel s attenuation 21steps 2 SIGNAL This LED indicates presence of signal at the inputs TEMP This LED shows temperature protection is active PMS LED indicating PMS in operation ICL LED indicating Intelligent Clip Limiter in operation 3 Main Power Switch Position Connects the amplifier s current feed Blue LED on Position O disconnects the Power Position II optional Stand by Mode The Amp s Power is activated remotely via Ethernet Amber LED 4 Display 5 Encoder with push button 0000 DO g LINX pro aAudio 2 2 Rear Panel See Figure B 1 Sign
3. SA USER MANUAL V 11 08 USNX Sx 2200 300 Eso SX 4002 ES Ea Ha Valencia Spain www lynxproaudio com SX series Manufacturer LYNX Pro Audio S L Calle 7 Pol Ind Picassent pro audio E 46220 Picassent Valencia Ce CE CERTIFICACTION EUROPEAN PRODUCT RoHS Directive 2002 95 EC This user manual is property of Lynx Pro Audio S L Any reproduction of this manual by any means is strictly prohibited Copyright 2011 All rights reserved 1 INTRODUCTION q i Un ASR oh Se Pan Oe oe O SA O OR PE a tr RAD PS 5 1 2 Main SpeCINCANONS seraa aa e thin dida ate Oaedatse 5 2 HARDWARE CONTROLS PS VR iat S 1 Me aS 6S en eg ee OE en o a do T 2 2 Rear Panel cestas as eee aa 8 3 INSTALLATION AND OPERATION Ou CONNECUON Si E A 9 AO AA a a a 10 do AS EA S S ET snedaten 11 34 TFOUDlESMOO UN soora a a 12 4 DECLARATION OF CONFORMITY Electrical appliance The exclamation mark within a triangle identifies the presence of electricity Use the system carefully without wet hands or feet Avoid installing the speaker in wet or excesivelly humid places Regularly check the condition of the cables and make sure these are not being walked on or pinched Connect the speaker to bipolar earthed mains The mains plug must be connected to the appropriate protection fuse or breaker Connection to any other type of mains could result in an e
4. al Input Female Neutrik XLR Connectors for the amplifier s signal input Signal Link 2 channels models only Male Neutrik XLR Connectors for daisy chaining input signal to other amplifiers parallel connected to female input connectors 2 Link Dual Switch in Link mode you can Link an Input to another adjacent input to use the same input signal In Dual mode each channel has an independent Input 3 Gain Selection Switch Gain Selection Switch Three position for 26 32 or 38dB Gain Default setting 32dB 4 Configuration Switch Sub sonic filter CL and Bridge 5 Speaker connectors Neutrik Speakon to connect the speakers VOO OOOO BALINPUT UNBAL INPUT Pt GND P13 GND P2 SIGNAL P2 SIGNAL IGNAL 17 220V 240V Fuse Inside o V a soHz60Hz Far o E Ca PE gt E E7 ne se E 3 r P a 0 Su _A o NY y LUN 3 Installation and Operation 3 1 Connections The Power switch must always be on the Off position before plugging the amp to a properly earthed mains socket 220 240V AC 110V 120V AC The input signal fed to the amplifier can be either balanced or un balanced The drawing below describes both ways to wire an XLR connector for the purpose Balanced Signal Connect pin 1 to Ground pin 2 to Signal hot and pin 3 to Signal cold Unbalanced Signal Connect Pin 1 to Ground pin 2 to Signal and pin 3 to Ground
5. b On the amplifier works without high pass subsonic filter Clip Limiter ICL enabled and Bridge mode ICL Clip Limiter Disabled the amplifier works without high pass subsonic filter Clip Limiter ICL disabled and no Bridge mode f m i lL Of E j n com 50H LE 0 Sub30Hz Sub On Bridge On jor ICL Of ub 30H 50H ED jon i Fl LE Ca Ed a o 3 oo nd SX LUN pro aAudio 3 3 Protection Systems ICL2 Intelligent Clip Limiter The ICL2 is an anticlip system to avoid speaker failure and provide more acceptable sound quality even when clipping occurs With the ICL2 system you don t lose the music punch but the speakers are kept under control PMS Power Management System This is a complete set of protections that monitors the main amp parameters load status signal input temperature current etc in order to draw from the power supply only the precise amount of current required to maintain safe operation during hazardous or extreme working conditions This system controls the amount of power that the amp delivers under three basic circumstances 1 The power on sequence where output is inhibited until the amp circuits are ready to operate This routine is repeated at every restart not just when the power switch is activated 2 When internal temperatures rise to near thermal shutdown point due to unfavourable operating conditions Here the system ta
6. kes control restricting current so as to maintain operational continuity at the precise power level which the amp is capable of withstanding at that particular moment 3 Excessive mains current consumption This event only occurs either under laboratory conditions long term sinusoidal signal testing with dummy loads or for example in field applications in conditions of prolonged acoustic howl round Here PMS takes control to avoid any damage to the speakers and to prevent the mains breaker from tripping or the fuses blowing SSP SOA Sentry Protection SOA Sentry protection effectively limiting the power that the amp could deliver into an incorrect load or to a direct short circuit This avoids power transistor failure WARNING The exclamation point inside an equilateral triangle indicates the existence of internal components whose substitution may affect safety The lightning and arrowhead symbol warns about the presence of uninsulated dangerous voltage SX LINX pro aAudio 12 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN To avoid fire or electrocution risk do not expose the unit to rain or moisture To avoid electric shock do not open the unit No user serviciable parts inside In the case of disfunction have the unit checked by qualified agents Class device 3 4 Troubleshooting In the event of incorrect connection or misfunctioning the amp will activate one or more of its LED to warn about the
7. lectrical shock and violate local electrical codes DO NOT CONNECT OR DISCONNECT THE AC POWER CONNECTORS UNDER LOAD Electrical shock risk The diagonal mark within a triangle identifies the presence of dangerous voltage Do not open or handle the interior of the amplifier These parts are not to be adjusted by the user For maintenance and or repair please go to an authorized service centre In order to reduce the risk of electric shock disconnect from AC before plug in or unplugging Audio signal cables Reconnect to AC only if all signal connections are made and secured Never manipulate the ground type plug provided The AC mains plugs should always remain accessible for operation Unplug the amplifier during storms or when it s being used for a long time Delicate Material Please ensure no foreign object or water enters the amplifier Do not place material that contains liquid on or near the unit Only clean the unit with dry cloths Do not use solvents SX CUN pro audio LUN Before starting to use the DSX amplifier please read this instruction manual carefully Keep these instructions in the place where the equipment will be used and with easy access to them 1 Introduction 1 1 Overview The SX Series Power Amps is our response to clients needs for a series of powerful compact versatile and rugged amplifiers characterised by no compromises electronic and mechanical specifications The SX Series offe
8. problem Correct function SGNL lights to indicate signal presence 0000 SGNL TEMP PMS ICL ICL The Intelligent Clip Limiter is operating 0006 SGNL TEMP PMS ICL No Signal No Input Signal is reaching the amp a hd QUO SGNL TEMP PMS ICL Overheating The amplifier has reached the maximum operational temperature Most common cause is the normal air flow is blocked accumulated dirt dust or object leaning against the grill Check and clean periodically O88 O0O SGNL TEMP PMS ICL PMS Several causes can trigger this LED most common are The amplifier is in power on sequence where output is inhibited until the amp circuits are ready to operate The internal temperatures rise to near thermal shutdown point due to unfavourable operating conditions Excessive mains current consumption OO 8 O SGNL TEMP PMS ICL SX LUNA Ce DECLARATION OF CONFORMITY LYNX Pro Audio S L Calle 7 Pol Ind Picassent E 46220 Picassent Valencia Lynx Pro Audio S L declares that SX series all models are in conformity with the following EC directives Low Voltage Directive 2006 95 EC Electromagnetic Compatibility EMC 2004 108 EC RoHS Directive 2002 95 EC In accordance with Harmonized European Norms EN 60065 2002 Audio video and similar electronic apparatus Safety requirements EN 55103 2 1996 Electromagnetic compatibility Product family standard for audio video audiovisual and entertainment lighting cont
9. r Crosstalk Required mains Dimensions W x H x T mm Weight RMS power 8Q RMS power 4Q RMS power 20 Bridge 80 Bridge 40 Pink noise Crest factor 4 ohm 2 ohm THD Sensitivity 8 Q Signal to noise ratio Gain Frecuency response 0 5dB Phase Response 1w Damping factor Crosstalk Required mains Dimensions W x H x T mm Weight SX 1004 4 x 690 W 4 x975 W 2 x 1950 W 4 x 1230 W 0 05 3 7 1 9 0 9 V 116 dB 26 32 38 dB 20 20K Hz 15dB gt 500 20 500Hz gt 75 dB 230V 50Hz 483 x 89 x 310 8 5 Kg SX 1600 2 x 460 W 2 x 790 W 2 x 1190 W 1580 W 2380 W 2 x 880 W 2 x 1360 W 0 05 3 0 1 5 0 8 V 113 dB 26 32 38 dB 20 20K Hz 15dB gt 500 20 500Hz gt 75 dB 230V 50Hz 483 x 89 x 310 8 Kg SX 4002 4 x 430 W 4x6 0 W 4 x 980 W 2 x 1340 W 2 x 1960 W 4 x 820 W 4x1170W 0 05 3 0 1 5 0 8 V 113 dB 26 32 38 dB 20 20K Hz 15dB gt 500 20 500Hz gt 75 dB 230V 50Hz 483 x 89 x 310 8 5 Kg SX 1200 2x 325 W 2x5 5 W 2 x 880 W 1150 W 1760 W 2x 610 W 2 x975 W 0 05 2 6 1 3 0 6 V 112 dB 26 32 38 dB 20 20K Hz 15dB gt 500 20 500Hz gt 75 dB 230V 50Hz 483 x 89 x 310 8 Kg SX 2800 2 x 810 W 2 x 1380 W 2 x 1950 W 2160 W 3900 W 2 x 1600 W 2 x 2460 W 0 05 4 0 2 0 1 0 V 116 dB 26 32 38 dB 20 20K Hz 15dB gt 500 20 500Hz gt 75 d
10. rol apparatus for professional use Part 2 Immunity WEEE Declaration Electrical and electronic equipment must be disposed of separately from normal waste at the end of its operational lifetime Please dispose of this product according to the respective national regulations or contractual agreements If there are any further questions concerning the disposal of this product please contact Lynx Pro Audio S L HINO pro audio
11. rs optional add on modules that extend its operational capability to match any of today s market requirements They incorporate unique absolute protections as the PMS or SSP systems 1 2 Main Specifications Instantaneous High Flow QuantaPulse EVO Power Supply e Ultra compact and lightweight 2 U high Laser cut aluminum front panels with integrated carrying handles Neutrik XLR input connectors input and signal link in 2 channel models e Input Link switch allow daisy chaining of the one channel input signal to another adjacent channel Neutrik Speakon output connectors Detented sealed potentiometers for easy recall of volume settings e ICL PMS Hi temp Signal indicators per channel Highly versatile with multiple configuration possibilites and additional module options e Switchable ICL clip limiters per channel e Switchable and selectable 30 or 50 Hz sub sonic highpass filter per channel Three position gain selector 26 32 or 38 dB Dual or Bridge mode operation Twin continuously variable temperature controlled back to front cooling fans Oversized power components high SOA reserve specification SX RMS power 80 RMS power 4Q RMS power 2Q Bridge 8Q Bridge 4Q Pink noise Crest factor 4 ohm 2 ohm THD Sensitivity 8 Q Signal to noise ratio Gain Frecuency response 0 5dB Phase Response 1w Damping facto
Download Pdf Manuals
Related Search