Home

FESTIVAL

1. 12 7 Troubleshootino Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The fixture does not work no light 1 2 Check the connection of power and main fuse Measure the mains voltage on the main connector Not responding to DMX controller DMX LED should be on If not check DMX connectors cables to see if link properly If the DMX LED is on and no response to the channel check the address settings and DMX polarity If you have intermittent DMX signal problems check the pins on connectors or on PCB of the fixture or the previous one 4 Try to use another DMX controller 5 Check if the DMX cables run near or run alongside to high voltage cables that may N cause damage or interference to DMX interface circuit Some fixtures don t respond to the easy controller You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal Wrong DMX address in the fixture Set the proper address No response to the sound Make sure the fixture does not receive DMX signal Check microphone to see if it is good by tapping the microphone One of the channels is not working well The stepper motor might be damaged or the cable connected to the PCB is broken The motor s drive IC on the PCB might be out of condition 8 Fixture Cleaning The cleaning of internal must b
2. UP button to select the Lou color 1 or Cois color 15 Once select press ENTER button to setup or automatically exit menu mode without any change after one minute To go back to the functions without any change press the MENU button I Sound mode Press the MENU button up to when the is shown on the display Pressing ENTER button Use DOWN and UP button to select the Sound on or sound off Pressing ENTER button Use DOWN and UP button to select the BP or BP ol or bP Jl mode Once select press ENTER button to setup or automatically exit menu mode without any change after one minute To go back to the functions without any change press the MENU button SPAS Sound sensitivity Press the MENU button up to when the SEnS is shown on the display Pressing ENTER button Use DOWN and UP button to change the number D OF Hine Once select press ENTER button to setup or automatically exit menu mode without any change after one minute To go back to the functions without any change press the MENU button Blackout mode Press the MENU button up to when the bind is shown on the display Pressing ENTER button Use DOWN and UP button to select the Nes blackout or normal Once select press ENTER button to setup or automatically exit menu mode without any change after one minute To go back to the functions without any change press the MENU button LED displey Press the MENU button up to when
3. the Led is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select display on or oF Fldisplay off mode Once select press ENTER button to setup or exit menu mode without any change after one minute Back to the functions without any change press MENU button again Display Inverse ii i Press MENU button until is blinking on the display Use DOWN and UP button to select normal or dS iE inverse press ENTER button to setup Back to the functions without any change press MENU button t 5 Self Test Press the MENU button up to when the test is blinking on the display Pressing ENTER button and the unit will run the built in programmer for self test To go back to the functions press the MENU button CLE F mu 5 Fixture Hours Press the MENU button up to when the rhe is blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button a Software version Press the MENU button up to when the Ler is blinking on the display Pressing ENTER button and the display will show the version of software of the unit To go back to the functions press the MENU button again 4 How To Control The Fixture You can operate the unit in three ways 1 By master slave built in preprogram function 2 By easy controller 3 By DMX controller No need to turn the unit off
4. when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show 787 on the display After that the unit will be ready to receive DMX signal or run the built in programs 4 1 Master Slave Built In Preprogrammed Function By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated cc show This function is when you Sh Ovenins show show 1 or or 2 show 12 and speed Its DMX input jack will have nothing plugged into it and its master LED will be constantly on and sound LED will flash to the music The other units will have to select normal or SL c 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave LED lights will be constantly on 2 light show In slave mode Gi i means the unit works as the master unit and means 2 light show In order to create a great light show you can set on the second unit to get contrast movement to each other even if you have two units only 4 2 Easy Controller by CA 8 The easy remote control is used only in master slave mode There is a fas terminator for connect the easy controller inside the fixture By r 5 connecting the cable into DMX IN waterproof cable entry gland to the CA 8 terminator of the first fixture you will find that the remote control on the first fixture will control all the ot
5. FESTIVAL TABLE OF CONTENTS DMX512 sine 1 Safety Instructions 2 Technical Specifications 3 How To Set The Fixture 4 How To Control The Fixture 5 DMX 512 Configuration 6 DMX 512 Connections 7 Troubleshooting 8 Fixture Cleaning User Manual Please read the instructions carefully before use 1 Safety Introductions e Possibly hazardous optical radiation emitted from this product For power supply if the Voltage is 230V do not connect in series much more le eee cag Hed aa A a A than 16 units use another mains supply for next 16 units If the Voltage is information about the installation operation and maintenance i WARNING 120V do not connect in series much more than 8 units use another mains supply for next 8 units e Please keep this User Manual for future consultation If you sell the fixture to another user be sure that they also receive this instruction booklet e Unpack and check carefully there is no transportation damage before using the fixture 2 Technical Specifications e It s important to ground the yellow green conductor to earth in order to avoid electric shock i l l o l e 5 LED clusters each equips with 64 high power LEDs e Disconnect main power before servicing and maintenance l e 4 DMX control channels Function Chase Speed and Strobe e Maximum ambient temperature is Ta 40 C Don t operate it where the temperature is higher than this e Inthe event of seriou
6. e carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the fixture s optics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days 14 EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN60598 1 2000 ALL 2000 A12 2002 Safety of household and similar electrical appliances Part 1 General requirements Innovation Quality Performance 15
7. ensitive Blackout Mode Yes Blackout Blackout Mode No Blackout ER on LED on off LED off gr opH SP Normal d5 irl Inversion t PSE Self Test Chro Fixture Hours ufr Software Version H CIC DMX 512 Address Setting Press the MENU button up to when the Addl is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX 512 address Once the address has been selected press ENTER button to setup or automatically exit menu mode without any change after one minute Back to the previous functions without any change press MENU button Slave Mode Press the MENU button up to when the Sind is shown on the display Pressing ENTER button Use DOWN and UP button to select the slave 1 or Slave 2 mode Once select press the ENTER button to setup or automatically exit menu mode without any change after one minute To go back to the functions without any change press the MENU button Show Mode Press the MENU button up to when the SHAtd is shown on the display Pressing ENTER button Use DOWN and UP button to select the Random show or show 1 or Show 2 or or show 12 Once select press ENTER button to setup or automatically exit menu mode without any change after one minute To go back to the functions without any change press the MENU button LOLI coor mode Press the MENU button up to when the Lol is shown on the display Pressing ENTER button Use DOWN and
8. her fixtures for Stand by Function and Mode functions 1 White Strobe Select Speed 2 Color Strobe 1 Fast 3 Sound White Strobe 2 Middle 4 Sound Color Strobe 3 Slow 4 3 DMX Controller Using universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal Press the MENU button up to when the Cor js showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically one minute later To go back to the functions without any change press the MENU button again If you use please refer to the following diagram to address your DMX512 channel for the first 4 2 units 5 DMX512 Configuration DMX 512 SONNGUFANAN Function Chase Speed airoso 250 255 f Sound Active 235 255 Chase 12 214 234 Chase 11 HHHH 130 249 Asynchronous 192 213 a 7 show 171 191 ase 150 170 Chase 8 HHH 128 149 Chase 7 010 255 107 127 Chase 6 WH 086 106 Chase 5 Synchronous 064 085 Chase 4 010 123 1 Show 043 063 Chase 3 H 022 042 Chase 2 Slow 000 021 Chase 1 EEA 000 009 Orr 000 009 ofi O 4 channels as a group please refer to the DMX configuration of 4 channels to control the other channels 11 6 DMX512 Connectio
9. ld up inside of the unit which will seriously damage F unit nH 3 How To Set The Fixture 3 1 Control Panel 32145 1 Display To show the various menus and the selected functions LED Button 7 DOWN To go backward in the selected functions 8 UP To go forward in the selected functions 9 ENTER To confirm the selected functions 10 Only for remote control By connect to the 1 4 microphone jack to control the unit for Stand by Function and Mode function 11 DMX output For DMX512 link use 3 pin XLR plug cable to link the next unit 12 DMX input For DMX512 link use 3 5 pin XLR plug cable to input DMX signal 13 Mains output Connect to supply mains power for the next unit 14 Mains input Connect to supply mains power To select any functions press MENU button until the required one is shown on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mode has been selected press ENTER button to setup or it will automatically return to the main functions without any change after idling one minute Back to the functions without any change press MENU button The main functions are shown below MENU DMX512 Address Setting Si Slave Mode Normal un aes mm Li SL o Slave mode 2 Light Show Random Show Show mode 0 12 Color1 15 on Sound Mode on HE Sound Mode off Sound S
10. ns The DMX512 is widely used in intelligent lighting control with a maximum of 512 channels o COMMON i DMX INPUT es M 13 px output k F d D M x a AS To f Termination reduces signal errors and to avoid signal 5 transmission problems and interference Itis always 29 advisable to connect a DMX terminal wy Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 Connect the fixture together in a daisy chain by XLR plug cable from the output of the fixture to the input of the next fixture The cable cannot be branched or split to a Y cable Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 2 The DMX output and input connectors are pass through to maintain the DMX circuit when one of the units power is disconnected 3 At last fixture the DMX cable has to be terminated with a terminator to reduce signal errors Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last fixture 4 Each lighting fixture needs to have an address set to receive the data sent by the controller The address number is between 1 512 5 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Pin4 5 not used
11. s operating problem stop using the fixture immediately Never try e Three operation modes DMX Master Slave mode Sound Active e Great built in programs under Master Slave triggered by music l l l l l e Optional easy controller CA 8 to repair the fixture by yourself Repairs carried out by unskilled people can lead to l l l l l e LED display for easy navigation damage or malfunction Please contact the nearest authorized technical assistance l l l e deal for discos pubs parties clubs Mobile DJs etc center Always use the same type spare parts e Do not connect the device to any dimmer pack e Voltage AC100V 240V 50 60Hz e Power consumption 40W e LED Total 320pcs Red 80pcs Green 80pcs Blue 80pcs White 80pcs e Size 302x297x324 mm e Weight 4 5kgs e Do not touch any wire during operation and there might be a hazard of electric shock e To prevent or reduce the risk of electrical shock or fire do not expose the fixture to rain or moisture e The housing must be replaced if they are visibly damaged e Do not look directly at the LED light beam while the fixture is on e There are no user serviceable parts inside the fixture Do not open the housing or attempt any repairs by yourself In the unlikely event your fixture may require service please contact your nearest dealer e Due to the magnifying type lens please keep the lens out of contact with direct sunlight Direct sunlight can cause heat to bui

FESTIVAL

Contents

Download Pdf Manuals

Related Search

Related Contents