ColorFlat 12 5 Watt
Contents
1. 1 LED Display 2 Attachment eyelet for safety rope 0 0 0 0 3 DMX In socket Safety rope 0 0 0 4 DMX Out socket A EE AAs 5 Programming buttons TN A z 6 IEC output socket JEN 7 Power supply 8 Fuse holder DMX OUT Ground Co CD 2 S gn 3 Sagna INSTALLATION The device can be installed on the ground or on the wall or ceiling Overhead rigging DANGER TO LIFE Please consider the EN 60598 2 17and the respective national standards during the installation The installation must only be carried out by an authorized dealer The installation of the device has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation 4016 Harry Hines Blvd Dallas Texas 75219 e 972 650 1855 ColorFlat 12 5 Watt 4 in 1 LED Par Light The installation must always be secured with a secondary safety attachment e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails When rigging derigging or servicing the device staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking int2. DANGER TO LIFE Before taking into operation for the first time the installation has to be approved by an expert DMX512 control The wires must not come into contact with each other otherwise the devices will not work at all or will not work properly A N Please note the starting address depends upon which controller is being used A N Only use a DMX cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another Occupation of the XLR connection DMX output DMX input XLR mounting socket XLR mounting plua 1 Ground 2 Signal 3 Signal Ground Signal Signal Ww N If you are using controllers with this occupation you can connect the DMX output of the controller directly with the DMX input of the first device in the DMX chain If you wish to connect DMX controllers with other XLR outputs you need to use adapter cables Building a serial DMX chain Connect the DMX output of the first device in the DMX chain with the DMX input of the next device Always connect one output with the input of the next device until all devices are connected Caution At the last fixture the DMX cable has to be terminated Plug the terminator with a 120 Q resistor between Signal and Signal in the DMX output of the last fixture Master Slave operation The master slave operation enables that several devices can be synchronized and controlled by o
3. device Wrong voltages or power outlets can lead to the destruction of the device and to mortal electrical shock Always plug in the power plug last The power plug must always be inserted without force Make sure that the plug is tightly connected with the outlet Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Never touch them with wet hands as this could lead to mortal electrical shock Never modify bend strain mechanically put pressure on pull or heat up the power cord Never operate next to sources of heat or cold Disregard can lead to power cord damages fire or mortal electrical shock The cable insert or the female part in the device must never be strained There must always be sufficient cable to the device Otherwise the cable may be damaged which may lead to mortal damage Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time If extension cords are used make sure that the core diameter is sufficient for the required power consumption of the device All warnings concerning the power cords are also valid for possible extension cords Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord Otherwise the cable or plug can be damaged leading
4. 55 ColorFlat 12 5 Watt 4 in 1 LED Par Light Sets the DMX starting address The unit occupies 4 DMX channels DMX Channel o hOB o The unit occupies 6 DMX channels EUDANN CA The unit occupies 7 DMX channels Dimmer mode Press the MODE button to select the dimmer mode Select the desired color via the SET UP button You can select the desired values via the UP or DOWN buttons Press the SET UP button to select the flash speed You can select the desired values via the UP or DOWN buttons Sound controlled mode Press the MODE button to select the sound controlled mode In sound controlled mode there are 2 sub menus to choose from Please press the SET UP button to reach the selection IO Cc At Hopd gd8bB you can select the desired programs via the UP or DOWN buttons At 88p8 88 HA you can select the desired sensitivity via the UP or DOWN buttons Auto mode Press the MODE button to select the auto mode In auto mode there are 3 sub menus to choose from Please press the SET UP button to reach the selection at RAAB8 ARBB you can select the desired fading color program via the UP or DOWN buttons ri you can select the desired switching color program via the UP or DOWN buttons At SPL i SF if you can select the desired speed of the color programs AF or AJ via the UP or DOWN buttons Static color mode Press the MODE button to select the static color mode In this mode there are 2 sub menus to choose from P
5. ColorFlat 12 5 Watt 4 in 1 LED Par Light High Power LED Flat Par Light 12 5 watt Four in One LED s Specifications e Power Supply AC110 240V 50 60Hz e Fuse 5A e Total Power 65W e LED s 12x5W 4 in 1 LED s e Angle of Optical Lens 40 Degrees e Channel 7 channels e Static Color Select Mode 15 Colors to choose e Dimmer Mode Dim down Red Green Blue and White e Color Jumping Mode e Color Washing Mode e Auto Program Mode e Sound Activation Mode e Slave Mode e Display Blue Screen 4buttons from left to right Menu Down Up Enter e Size 11 x 4 x 12 e Weight 6 5 Ibs 4016 Harry Hines Blvd Dallas Texas 75219 e 972 650 1855 ColorFlat 12 5 Watt 4 in 1 LED Par Light ColorFlat 5 ColorFlat 12 QCL CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing For your own safety please read this user manual carefully before you initially start up Every person involved with the installation operation and maintenance of this device has to be qualified follow the instructions of this manual consider this manual to be part of the total product keep this manual for the entire service life of the product pass this manual on to every further owner or user of the product download the latest version of the user manual from the Internet INTRODUCTION Thank you for having chosen a ColorFlat Fixture If you follow the instructions g
6. R TO LIFE Disconnect from mains before starting maintenance operation We recommend a frequent cleaning of the device Please use a soft lint free and moistened cloth Never use alcohol or solvents There are no serviceable parts inside the device except for the fuse Maintenance and service operations are only to be carried out by authorized dealers Replacing the fuse If the fine wire fuse of the device fuses only replace the fuse by a fuse of same type and rating Before replacing the fuse unplug mains lead Procedure Step 1 Open the fuse holder on the rear panel with a fitting screwdriver Step 2 Remove the old fuse from the fuse holder Step 3 Install the new fuse in the fuse holder Step 4 Replace the fuse holder in the housing Should you need any spare parts please use genuine parts If the power supply cable of this device becomes damaged it has to be replaced by a special power supply cable available at your dealer Should you have further questions please contact your dealer 4016 Harry Hines Blvd Dallas Texas 75219 e 972 650 1855 ColorFlat 12 5 Watt 4 in 1 LED Par Light TECHNICAL SPECIFICATIONS Po ColorFlat SxSW ColorFlatt2x5W Dimensions WxDxH 230 x 110 x 270 mm 270 x 110 x 310 mm Weight 3 5 kg Maximum ambient temperature T 45 C 4016 Harry Hines Blvd Dallas Texas 75219 e 972 650 1855
7. allas Texas 75219 e 972 650 1855 ColorFlat 12 5 Watt 4 in 1 LED Par Light OPERATING DETERMINATIONS This device is a lighting effect for creating decorative effects This product is only allowed to be operated with an alternating voltage of 230 V 50 Hz and was designed for indoor use only This device is designed for professional use e g on stages in discotheques theatres etc Lighting effects are not designed for permanent operation Consistent operation breaks will ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others This device must never be operated or stockpiled in surroundings where splash water rain moisture or fog may harm the device Moisture or very high humidity can reduce the insulation and lead to mortal electrical shocks When using smoke machines make sure that the device is never exposed to the direct smoke jet and is installed in a distance of 0 5 meters between smoke machine and device The room must only be saturated with an amount of smoke that the visibility will always be more than 10 meters The ambient temperature must always be between 5 C and 45 C Keep away from direct insulation particul
8. arly in cars and heaters The relative humidity must not exceed 50 with an ambient temperature of 45 C This device must only be operated in an altitude between 20 and 2000 m over NN Never use the device during thunderstorms Over voltage could destroy the device Always disconnect the device during thunderstorms The symbol q ao determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 0 1 meters This device is only allowed for an installation via the mounting bracket In order to safeguard sufficient ventilation leave 50 cm of free space around the device The housing must never touch surrounding surfaces or objects Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Always fix the fixture with an appropriate safety bond The maximum ambient temperature T 45 C must never be exceeded Operate the device only after having become familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Never use solvents or aggressive detergents in order to clean the device Rather use a soft and damp cloth Please use the original packaging if the device is to be transported Make sure that you pack the device in the original state Please consider that unauthorized modifications on th
9. e e White Blue Green Red No function 0 255 0 255 0 255 0 255 0 100 0 100 0 100 0 100 Dimming 0 255 0 100 016 255 Ce f sra cr noreasing No No No No unction unction function function Speed tour eat 185 189 Color change 5 190 194 Color change 6 195 200 Color change 7 201 205 Color change 8 4016 Harry Hines Blvd Dallas Texas 75219 e 972 650 1855 ColorFlat 12 5 Watt 4 in 1 LED Par Light 41 206 209 Color a ed 99ers 9 Sensitivity 49 246 255 Sound active 32 255 CLEANING AND MAINTENANCE The operator has to make sure that safety relating and machine technical installations are inspected by an expert after every four years in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are inspected by a skilled person once a year The following points have to be considered during the inspection 1 All screws used for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on housings fixations and installation spots ceiling Suspension trussing 3 The electric power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed DANGE
10. e device are forbidden due to safety reasons Never remove the serial barcode from the device as this would make the guarantee void If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock crash etc 4016 Harry Hines Blvd Dallas Texas 75219 e 972 650 1855 ColorFlat 12 5 Watt 4 in 1 LED Par Light DESCRIPTION OF THE DEVICE Features ColorFlat LED spot with 5 W QCL e Equipped with 4in1 quad color LEDs for homogeneous light output e Flat housing form requires minimal space when rigging e Second mounting bracket for safe standing installation e Comfortable addressing and setting via control panel with LED display e Functions Static colors RGB color blend internal programs dimmer strobe sound control sensitivity e Further display settings display on or off display inverted default settings e Operable in stand alone mode or via DMX e Master Slave for parallel operation of several devices e DMX512 control via regular DMX controller e Number of DMX channels selectable for numerous applications e Sound control via built in microphone e Ready for connection with power cord and safety plug e Feed through output allows powering another device e After every 8 devices the fixtures must have a renewed connection with the Overview
11. fter every 8 devices the fixtures must have a renewed connection with the power mains OPERATION After you connected the spot to the mains the device starts running The LED display lights up and you can choose the desired mode via the buttons MODE SET UP UP and DOWN See following graphic MODE SET UP UP DOWN FUNCTION Red LLL Agivsttte intensity of the red color Green m Adjust the intensityfef thd dreentel r DIMMER Blue Bonn be5S Adjust the intensity of the blue color White HoH HESS Adjust the intensity of the white color Flash speed E O00 F5 I5 F SOL is of FSU i is slowest 5 I5 is fastest increasing Program selection Do 5o G Select the internal sound controlled program SOUND Sensitivity selection SHAA GERA 5_i is lowest level 5_ is highest level increasing Fading colors AF I A IG Select the internal fading color program AUTO Switching colors AJ AJIB Select the internal switching color program Speed set CP i SP Ib Adjust the speed of the internal programs STATIC Color select L O IS select static color a T FABE AG I5 FSGE is off FSU iS slowest F 5 I5 is fastest Display don LED digital display always on on off do F LED digital display off OTHER Display Con LED digital display normal normal inverse AJH LED digital display inverted Default setting JEFA Initialize the default settings 4016 Harry Hines Blvd Dallas Texas 75219 e 972 650 18
12. g on the device will automatically detect whether DMX 512 data is received or not If there is no data received at the DMX input the control displays flashes This function is only available if the display I mode under Other was set to 00m This situation can occur if the 3 PIN XLR plug cable with DMX signal from controller is not connected with the input of the device the controller is switched off or defective the cable or connector is defective or the signal cable is not well connected DMX Channel Selection Choosing a DMX Channel Mode After having set the desired address you can now choose a DMX Channel Mode 4 CH 6 CH 7 CH Please press the SET UP button until the display shows DAU LALA EL Set the desired mode via the UP or DOWN buttons DMX protocol 4 channel mode In this mode the last possible starting address is 509 CH Value Function 000 255 Red 0 100 000 255 Green 0 100 000 255 Blue 0 100 000 255 White 0 100 6 channel mode In this mode the last possible starting address is 507 CH Value Function Green 0 100 Blue 0 100 White 0 100 Dimmer 0 100 4016 Harry Hines Blvd Dallas Texas 75219 e 972 650 1855 ColorFlat 12 5 Watt 4 in 1 LED Par Light 000 Nofunction 001 010 Sound Control 011 255 Strobe increasing 7 channel mode In this mode the last possible starting address is 506 CH4 CH3 CH2 CH1 CH7 CH6 CH5 wots Mav
13. ighly inflammable material decoration articles etc within a distance of min 0 5 m Mount the device to your trussing system using an appropriate clamp For overhead use always install an appropriate safety bond You must only use safety bonds complying with DIN 56927 quick links complying with DIN 56927 shackles complying with DIN EN 1677 1 and BGV C1 carbines The safety bonds quick links shackles and the carbines must be sufficiently dimensioned and used correctly in accordance with the latest industrial safety regulations e g BGV C1 BGI 810 3 Please note for overhead rigging in public or industrial areas a series of safety instructions have to be followed that this manual can only give in part The operator must therefore inform himself on the current safety instructions and consider them The manufacturer cannot be made liable for damages caused by incorrect installations or insufficient safety precautions Pull the safety bond through the attachment eyelet and over the trussing system or a safe fixation spot Insert the end in the quick link and tighten the safety screw The maximum drop distance must never exceed 20 cm 4016 Harry Hines Blvd Dallas Texas 75219 e 972 650 1855 ColorFlat 12 5 Watt 4 in 1 LED Par Light A safety bond which already held the strain of a crash or which is defective must not be used again Adjust the desired inclination angle via the mounting bracket and tighten the fixation screws
14. iven in this manual we are sure that you will enjoy this device for a long period of time Unpack your ColorFlat SAFETY INSTRUCTIONS CAUTION Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching the wires This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual ics Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature 4016 Harry Hines Blvd Dallas Texas 75219 e 972 650 1855 ColorFlat 12 5 Watt 4 in 1 LED Par Light Please make sure that there are no obvious transport damages Should you notice any damages on the A C connection cable or on the casing do not take the device into operation and immediately consult your local dealer This device falls under protection class The power plug must only be plugged into a protection class outlet The voltage and frequency must exactly be the same as stated on the
15. lease press the SET UP button to reach the selection Cit FI Tf IC LS At OO O0 U you can select the desired color via the UP or DOWN buttons A FoOUU FS 15 you can select the desired flash speed of the selected color via the UP or DOWN buttons Other mode In this mode there are 3 sub menus to choose from Please press the SET UP button to reach the selection as appropriate Atgon and doFF via the UP or DOWN buttons you can decide if the display should always be on or 4016 Harry Hines Blvd Dallas Texas 75219 e 972 650 1855 ColorFlat 12 5 Watt 4 in 1 LED Par Light if it should turn off after 60 seconds of inactivity AtSEndand J viathe UP or DOWN buttons you can decide if the display should display normally or if it should display upside down At OEHHA you can reset to ex works setting Please push the UP and DOWN buttons at the same time The display shows H_i 1 and the color switching programs begin to run DMX mode The Control Board allows you to assign the DMX fixture address which is defined as the first channel from which the device will respond to the controller Addressing 90000 o Press the MODE button to select the DMX mode and the display shows MLI t m io IL Ta I You can select the desired addresses via the UP or DOWN buttons Controlling After having addressed the device you may now start operating it via your lighting controller Note After switchin
16. ne master device On the rear panel of the device you can find an XLR jack and an XLR plug which can be used for connecting several devices Choose the device which is to control the effects This device then works as master device and controls all other slave devices which are to be connected to the master device via a DMX cable Connect the OUT jack with the IN plug of the next device 4016 Harry Hines Blvd Dallas Texas 75219 e 972 650 1855 ColorFlat 12 5 Watt 4 in 1 LED Par Light Connection with the mains Connect the device to the mains with the enclosed power supply cable The occupation of the connection cables is as follows International Neutral N Earth Blue Yellow Green The earth has to be connected If the device will be directly connected with the local power supply network a disconnection switch with a minimum opening of 3 mm at every pole has to be included in the permanent electrical installation The device must only be connected with an electric installation carried out in compliance with the IEC standards The electric installation must be equipped with a Residual Current Device RCD with a maximum fault current of 30 mA Lighting effects must not be connected to dimming packs On the rear panel there is an IEC socket Power Out Connect the output with the mains input of the next fixture until all fixtures are connected Please note A maximum of 8 devices may be linked together A
17. o operation another time The operator has to make sure that safety relating and machine technical installations are approved by an expert after every four year in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year Procedure The device should be installed outside areas where persons may walk by or be seated IMPORTANT OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the device If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property The device has to be installed out of the reach of people If the device shall be lowered from the ceiling or high joists professional trussing systems have to be used The device must never be fixed swinging freely in the room Caution Devices in hanging installations may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do NOT install the device Before rigging make sure that the installation area can hold a minimum point load of 10 times the device s weight DANGER OF FIRE When installing the device make sure there is no h
18. to mortal electrical shock If the power plug or the power switch is not accessible the device must be disconnected via the mains If the power plug or the device is dusty the device must be taken out of operation disconnected and then be cleaned with a dry cloth Dust can reduce the insulation which may lead to mortal electrical shock More severe dirt in and at the device should only be removed by a specialist There must never enter any liquid into power outlets extension cords or any holes in the housing of the device If you suppose that also a minimal amount of liquid may have entered the device it must immediately be disconnected This is also valid if the device was exposed to high humidity Also if the device is still running the device must be checked by a specialist if the liquid has reduced any insulation Reduced insulation can cause mortal electrical shock There must never be any objects entering into the device This is especially valid for metal parts If any metal parts like staples or coarse metal chips enter into the device the device must be taken out of operation and disconnected immediately Malfunction or short circuits caused by metal parts may cause mortal injuries HEALTH HAZARD A Never look directly into the light source as sensitive persons may suffer an epileptic shock especially meant for epileptics Keep away children and amateurs Never leave this device running unattended 4016 Harry Hines Blvd D
Download Pdf Manuals
Related Search