USER MANUAL LL ARC POINT OneChip BASIC
Contents
1. LL SPLITTER RGB max 25W Power connection 24V DC 1 5m cable with 6pin LINE connector to SPLITTER Net weight 0 2 kg IP IP43 Ambient temp Ta Maximum 40 C Cooling Conventional Materials and finish Housing powder painted anodized aluminium RAL9006 other colours on request Installation Surface suspended recessed or in ground mounting P5 Il RGB Red and Green and Blue Edition A 2010 LL ARC POINT RGB SPLITTER Input 24V with 6pin Line connector Output 24V 6xOut with 6pin Line connector Net weight 0 2 kg Dimensions LxWxH 156mm x 68mm x 16mm IP IP20 Ambient temp Ta Maximum 40 C Cooling Conventional Materials and finish Powder painted anodized aluminium RAL9006 other colours on request Installation Any position surface mounting 03 INSTALLATION 03 1 Unpacking Unpack carefully This is electronic equipment and should be handled carefully Damaged delivered package or if are any mechanical parts broken it must be claim immediately by the transport company Photo pictures as evidence are valuable for future claim 03 2 Physical installation Loading capacity of bearing area has to be at least 10 times the weight of all device clusters luminaries clamps cables Hairbreadth from combustible materials is 0 5m 03 3 Electrical installation ZN To tackle all Safety Information 01 You can suffer a dangerous electric shock by using a high voltage AC DC power s2. Leader Light s r o M Gorkeho 33 SK 052 01 Spisska Nova Ves Slovakia www leaderlight eu USER MANUAL LL ARC POINT OneChip BASIC LEADER LICHT professional lighting products COMPLIMENTS ON YOUR PURCHASE All dimensions are in milimeters 40 9 lt Following items are included Fitting LL ARC POINT with 1 5m cable and 6pin LINE connector 1 pc User manual 1 pc Additional items needed LL ARC POINT SPLITTER must be ordered separately ARC DRIVER DC power supply 24V Controller compatible with DMX Mounting accessories as necessary Surface mounting Screws and washers M6 Content 01 SAFETY INFORMATION 01 1 Risk of eyes damage 01 2 Protection from electric shock 01 3 Fire prevention 02 PRODUCT SPECIFICATION 02 1 Technical Specification 03 INSTALLATION 03 1 Unpacking 03 2 Physical installation 03 3 Electrical installation 04 MAINTENANCE ENVIRONMENT H E Do not throw away the appliance with the normal household waste at the end of its life but hand it in at an official collection point for recycling By doing this you help to preserve the environment MMX Leader Light All right reserved 01 SAFETY INFORMATION A WARNING Carefully read before installing powering or servicing Nothing to do if anything misunderstand Installation can be done only by a qualified professional in accordance with relevant local codes 01 1 Risk of
3. eyes damage A Do not look directly into LED lamps Do not look into light beam from a distance of less than 40 cm 16 inches 01 2 Protection from electric shock A Shut down power before installation or maintenance Luminaries Splitter Driver and recommended power supply must be installed by a qualified professional in accordance with relevant local codes Only acceptable source of power and frequency that complies with local building and electrical codes to use Do not use or do not connect the products if the power cable power plug or fixtures are any way damaged wet or if they are overheating Do not modify alter or attempt to service the LeaderLight appliance Doing so will void the warranty Before removing or installing any cover or part of appliance disconnect from power Operation only with LL ARC SPLITTER and DC 24V source By using a high voltage AC power supply danger of electric shock 01 3 Fire prevention A Follow all safety considerations Device never shield minimum distance around fitting must be 100mm 4 in LEDs never direct cover with filters or other materials Allowing max ambient temperature is 40 C 104 F 02 PRODUCT SPECIFICATION 02 1 Technical Specification Lamp type RGB 3x1W P5 Lifetime Long 50 000 hrs 70 degradation Optic Standard 25 on request 10 40 and EL Control data Input 3 channels dimming with SPLITTER Input power 6 x LLARC POINT RGB
4. upply by touching the AC DC power supply wires inside LLARC POINT LLARC POINT must be operated only with LLARC POINT SPLITTER After installing the LLARC DRIVER which is connected to the device MW power supply IN 100 260AC OUT 24V you are ready to make the connections from fixtures to LLARC SPLITTER It is not necessary to open fixture before connecting to LL ARC SPLITTER Pull the 6pin LINE cable connector from the fixtures to the LLARC SPLITTER output Wire the Brown Red White Green Black Blue wires of each fixture into the connector terminals see table Wire colour to connector terminals LLARC SPLITTER operate with LLARC DRIVER Connection ability see pictures Electrical Connections WARNING LLARC POINT OPERATE ONLY with LLARC POINT SPLITTER 04 MAINTENANCE ZN To tackle all Safety Information 01 Damage caused by inadequate cleaning or maintenance is not covered by warranty Regular cleaning is demand dust dirt Maintenance policy Unplug mains before maintenance and at least 10 minutes cool off Appliance do not illegal open or demount Clean up dust only from outer surface for ex diffuser and lenses Use vacuum or dumpy duster warm water Before reinstalling to check failure free state no wet parts If you have any question please contact support leaderlight sk Installation Mounting surface recesed in ground or suspended is easy using vario
5. us accessories as seen below 1 1 Mounting on surface with surface holder 1 4 Mounting in floor with in ground box Part A PartA Part B lt _ SS Vpart B _ O 1 1 1 Unlock the screws on the surface holder LL41 200 and divide it into two parts Part B Part A 1 1 2 The part B fix to the surface The power cable string on surface holder part A The surface holder part A screw on the basic unit 1 1 3 Connect the fixture to ARC SPLITTER and match part A on part B and fix with screws Cut out 49mm 1 4 1 The installation box insert in floor Connect the basic unit to ARC SPLITTER and put the fixture in the box Screw the front cover 1 5 Suspended mounting with suspended holder Mounting accessories 1 2 Recesed mounting with recesed holder 5 Cut out 49mm yp lt 1 2 1 The recessed holder LL41 230screw on basic unit Cut hole in suspended ceiling The aloved thickness of ceiling material is max 12mm E a minimal 150 mm i Ta 1 2 2 Connect the fixture to the ARC SPLITTER Push the spring and insert the fixture into the hole 1 3 Mounting on surface with bracket CLLK 1 3 1 The power cable string on bracket The bracket screw on the basic unit Connect the fixture to ARC SPLITTER and fix the bracket with screws to the surface LL41 200 LL41 230 LL41 300 1 5 1 The power cable string on suspended holder 4 The s
6. uspended holder screw on the basic unit R LL41 205 LL ARC POINT ELECTRICAL CONNECTIONS with SPLITTER LL ARC POINT RGB SPLITTER connection with LL ARC POINT OneChip RGB max 6 pcs ao oan same yyy gq 9 9 9 H H O 100 260V AC Connection conditions e Each SPLITTER Out to fitting must be connected e Maximal allowed current on SPLITTER Out is 3x0 35A e Maximal distance from fixtures to driver is 50m 164 feet dependence on cable diameter e Never use more fittings as maximal allowed amound e LLARC POINT SPLITTER is calculated only fo r LL ARC POINT fixtures Maximal allowed amound of fixtures per SPLITTER LL ARC POINT RGB SPLITTER Wire colour to connector terminals RGB SPLITTER Connector terminal Wire colour R Brown R Red G White G Green B Black B Blue 01 Ko 1o10 Product name Current LL39 500 LL ARC POINT BASIC OneChip RGB 3x0 35A LL41 420 LL ARC SPLITTER RGB 6xOut Accessories LL41 200 LL HOLDER ARC POINT SURFACE LL41 205 LL HOLDER ARC POINT SUSPENDED LL41 230 LL HOLDER ARC POINT RECESSED LL41 250 LL BOX ARC POINT IN GROUND LL41 300 LL BRACKET ARC POINT If you have any question please contact support leaderlight sk
Download Pdf Manuals
Related Search