USER`S MANUAL - Security Camera King
Contents
1. USER S MANUAL Thank you for purchasing our products Pleas read the manual carefully before operating Version YX ZX412912V01 30 Notes gt make the products under great impact or stay away from strong electromagnetic interference and vibration gt There are some sophisticated parts inside the camera therefore during transportation and installation please avoid the damage cause by stress or severe vibration For the sake of safety please do not switch on power before accomplishing all installation gt Please comply with all electrical safety standards during operation camera or signal transmission cable should maintain a sufficient distance 50 meters with high voltage equipment or cables if necessary lighting and thunder protective measures must be taken gt Please install the camera in well ventilated environment gt Please do not make the camera face sunshine or other strong light directly in case of any damage to the lens and the sensor gt temperature and humidity range for cameras work are 10 50 less than 90 separately please do not start cameras beyond this range gt To avoid lightning strikes please make sure the installation of power supply ground line in a good condition gt prevent the equipment from damage by shower or splash of water please do not place the device substances such as liquid Contents I Features II INTERFACE 2 1 Interface Menus2. 2 1 Interface v e e e e LEFT RIGT e DON Enter and Exit the menu UP DOWN Moving up and down LEFT RIGHT Modify the parameters OSD Press enter for 2 seconds to enter main menu as shown in picture 1 SETUP MENU 1 3 LENS AUTOR SHUTTER AGC MANUALd PICT ADJUST 4 WHITE BAL MANUAL d d SAVE ALL 3 1 Lens Auto Manual chose different mode according to the type of lens used on the camera AUTO IRIS WEE Be MODE AUTO SPEED nnou 080 RETURN 3 2 Shutter AGC Auto Manual a Auto Setup Mode with auto iris lens chose Auto Iris with Fixed iris lens chose Auto Iris Shutter Brightness 0 255 AUTO SETUP HIGH LUMINANCE MODE S UO LIRIS BRIGHTNESS LOW LUMINANCE MODE AGCASLOW BRIGHTNESS RETURNA b Manual Setup user can adjust the Shutter Mode Shutter Speed and AGC MANUAL SETUP Si 1 53 6 3 3 Picture Adjustment Mirror Off V FLIP H FLIP HV FLIP Contrast 0 63 Sharpness 0 15 PICT ADJUST ERROR CONTRAST 020 SHARPNESS 006 RETURN4 3 4 White Balance It can restore the authenticity of the color when it is affected by the change of temperature The user can choose different white balance mode accordingly ATW PUSH USER1 USER2 ANTI CR MANUAL PUSH LOCK 3 5 WDR Mode Full WDR on Normal WDR off Light Used in situation with bright light Contras Low Mid low Middle Mid high High WDR SETUP Ko
3. 3 1Lens 3 2Shutter AGC 3 3Pic adjustment 3 4White Balance ASWDIR s ua 3 7 HLC BLC 3 8D N Switch a 3 9 Bzoom c eme 12 3 10Dis 3 11Privacy Mask SA Motion Detection 13 3 14Camera ID Solo Language iioii eg Ere 15 3 16Reset 3 17Return NO 16 Safety Precaution Warning Dont dismantle without authori becareful thunder 9 Note avoid thunder strking please dont open the backcover the maintenance must be made by our authorized serviceman A This symbol means that there might exist uninsulated dangerous voltage inside the case be careful of electric shock A This symbol reminds you to pay attention to important operation and maintenance instructions in the accompanied information Warning gt In order to prevent damage caused by fire or electric shock please do not put cameras exposed in the moist environment or rainwater gt Please make sure the adapter is consistent with product specifications otherwise it might cause fire electric shock or damage gt Pay attention to polarity of the adapter it might cause some accidents like fires gt Please don t connect multiple cameras with the same adapter at the same time overloading of adapter capacity may cause fires gt Power supply must be firmly fixed so as not to loose to cause fires gt If the device gets abnormal smell or smoke
4. please stop it immediately and contact with our customer service center gt If the camera doesn t work as usual please do not dismantle it by yourself Please contact our local distributor or our maintenance office authorized by our company otherwise we won t promise warranty Please do not splash water on the product components when cleaning I Features 1 New Generation SONY CCD and DSP Adopting the latest CCD and DSP the camera can receive clear and lucid images even at circumstances with very low illumination 2 Wide Dynamic Range WDR WDR Camera adopts cutting edge and effective technology With this function it can see all the view both inside the house and outside of the window with different lighting 3 High Resolution 700TVL 4 DIN Switch Day amp Night cameras can switch automatically into color or B W according to optical changes 5 3D DNR Digital Noise Reduction Technology enhances the ability to handle with signal noise ratio this technology makes camera can receive more clear and vivid images even under low light conditions 6 Motion Detect Motion detection function can trigger alarm or recording when sensing moving objects users can set the sensitivity and multiple detection zones 7 Privacy Mask The Privacy Mask can block out sensitive areas from view covering the areas with a solid block of color you can adjust the mask position and size 8 OSD On Screen Display Menu II Interface
5. 1 Privacy 15 areas optional user can adjust the size position color transparency of the chosen area 3 12 Motion Detection Detection Sensitivity 0 127 Block Display On Off the block would show up when function is turned on Detect area setting related area for motion detection Monitor area 4 areas optional user can adjust the position of the area MOTION DET DETECT 111 BLOCK DISP OFF DETECT AREA 4 MONITOR AREA 4 RETURNd 3 13 Syne Mode Chose Next to go to the new page of Menu 13 SETUP MENU 2 3 HLC BLC 4 DAY NIGHT AUTOd EZOOM d DIS OFF PRIVACY d MOTION DET ONd BACKd EXITO SAVE ALL Sync Mode default setting Internal Sync SETUP MENU 3 3 SYNC INT CALERA rollo LANGUAGE ENGLISH CAMERA RESET SAVE ALL 3 14 Camera ID Set UP CAMERA ID SETUP RBCDEFGHI JKLMNOPQRSTUV WXYZ0123456789 amp 0 7 X 2 9 A s x inan CLR 4 RETURNd You can set the camera code as numbers uppercase letters and related symbols 11 Cursor for left and right CLR Clear camera name POS for position RETURN return to the upper menu 3 15 LANGUAGE Chinese English Japanese Optional SETUP MENU 3 3 SYNC INT CAMERA ID ON LANGUAGE Eire CAMERA RESET SAVE ALL 3 16 Camera Reset This function is to clear all parameters that has been saved and return t all parameters to default setting This process should be double conf
6. E CONTRAST RETURNG 3 6 DNR Digital Noise Reduction Technology can reduce the noise in low illumination condition Off Low Mid low Middle Mid high High Optional 10 SETUP MENU 1 3 LENS AUTO SHUTTER AGC AUTOd PICT ADJUST 4 WHITE BAL MANUAL d 8 WDR SE NEXTd EXIT SAVE ALL 3 7 HLC BLC SETUP MENU 2 3 DAY NIGHT EZOOM a DIS OFF PRIVACY MOTION DET BACKd EXITd SAVE ALL HLC is for strong light inhibition turn on this function when used in roa monitor The traffic violating vehicles will be clearly monitored CLIP is between 0 255 the bigger the value the stronger light inhibit effect Scale is betwes 7 the bigger the value the brighter the image cr Pini 000 4 3 8 Day Night a Auto Mode Image would be color during daytime tum into black amp white at night automatically DAY NIGHT SETUP BURST DELAY CNT DAYPNIGHT 016 NIGHT2DAY 080 OFF IR LED OFF EXTON OFF RETURNA b Color mode Image would always be color regardless of the changing of the lighting 3 9 Ezoom User can adjust the size and position of image EZOOM SETUP 000 PAN nnnnhunn 512 TILT 256 3 10 Dis This function is to shut down Ezoom fucntion SETUP MENU 2 3 HLC BLC 4 DAY NIGHT AUTOd EZOOM ps PRIVACY MOTION DET BACKd EXIT 3 1
7. cating led is always on or not b Check the video cable make sure it is workable c Check if the monitor has been open Image interference after installation Check the power quality if the adapter can t work please replace another one b Check if electromagnetic interference exists in the surroundings please use some anti interference devices 3 Q RS485 can t control menu Please check the controller issued code is correct b Please check if the control circuit is smooth c Please verify the communication address baud rate well matched 4 Please check if the connection interface is loose 4 Camera image can t switch into B W at night Please open the camera menu to see if Day Night Switch is set as AUTO if not please change into AUTO 5 Noise is very obvious at night with low illumination A please make sure AGC ON 6 Q The image color is abnormal A please make sure if the white balance is correctly set as Auto White Balance b Please enter the menu to restore factory settings Image appears to be whiter than usual after installation a Please check whether the lens aperture was adjusted too large so that the image appears whiter b Please verify the camera rear panel ifthe regulator potentiometer is adjusted too large Check if the brightness of the monit is too large 8 When installation image is not clear or exist dark corners a Please ad
8. irmed by the user before resetting SETUP MENU 3 3 SYNC INT CAMERA ID ONd LANGUAGE ENGLISH BACKd EXITd SAVE ALL 3 17 Return to front page 3 18 EXIT SAVE ALL 16 IV Specification 1 3 SONY DOUBLE SCAN CCD EFFIO P Chipset 4129 DSP y PAL 976 H x582 V NTSC 976 H 494 V System PAL NTSC WDR FULL FUNCTION NORMAL LIGHT SYNC INNER SYNC Shutter 1 53 1 100000s AGC AGC AGC Slow shutter S N Ratio gt 50dB AGC OFF Video output 1 0 750 Resolution 700TVL Minimum Color 0 1 Lux F1 2 50IRE AGC ON Illumination B W 0 001Lux F1 2 50IRE AGC ON D N Switch Color Auto D N Switch time 0 255 Lens style Manual Auto Privacy Zones 1 15zones Motion Detect 4 Zones Video output BNC ATW PUSH Userl User 2 Manual ANTI White Balance CR PUSH LOCK 17 Vertical Horizontal Vertical Horizontal Title Can be set Title Position Any position on the screen High Medium to high Medium Low to DNR medium Low Off OSD English Chinese Japanese Pic contrast 0 63 Pic sharpness 0 15 Power DC12V 10 Wattage 2 0W Operating 10 C 50 C Temperature Operating Humidity lt 90 Storage Temperature 40 C 60 C Storage Humidity 20 95 18 No image after installation a Check to connect the power supply correctly whether the indi
9. just focus and zoom of the lens Make sure the focus should be adjusted in a proper way b Please check if the lens is clean 19 Interface Function Introduction RIGT e b ENTER Push the joystick down to enter OSD menu UP DOWN Select the desired feature by using Joystick 1 with Up Down direction LEFT RIGHT Change the status of the selected feature by using Joystick with Left Right direction VIDEO TEST 2 VIDEO_OUT Additional video out for installation 3 LED LEVEL Adjusting brightness of IR LEDs
Download Pdf Manuals
Related Search