Distributed by AUSTRALIA Brown & Watson
Contents
1. switch can be used to disable the dual battery system this is particu larly useful if your Auxiliary battery is very flat disable the dual battery system before at tempting to crank the engine and then enable once the engine has started2. Distributed by AUSTRALIA Brown amp Watson International Pty Ltd rau PR JECTA Telephone 03 9730 6000 12 VOLT Facsimile 03 9730 6050 National Toll Free 1800 113 443 85 AMP SOLENOID NEW ZEALAND Narva New Zealand Ltd 22 24 Olive Road PO Box 12556 Penrose Auckland New Zealand Telephone 09 525 4575 Facsimile 09 579 1192 Complete kit contains the following 1 x 85A Solenoid 1 x Surge Protector 1 x 4m Battery Cable Red 1 x 60cm Battery Cable Black 1 x 3m Switch cable Blue 1 x Rocker Switch 2 x Large Battery Lugs 4 x Small Battery Lugs 1 x Positive Battery Terminal 1 x Negative Battery Terminal 2 x Black Heat Shrink 4 x Red Heat Shrink 2 x Insulated Blade Terminals 4 x Insulated Ring Terminals 1 x Wire Tap white 10 x Cable Ties 2 x Solenoid Mounting Screws prowecta 12 VOLT AUTO COMPUTER PROTECTOR ISO18 Issue 2 21 3 12 WARNING e PLEASE READ THESE INSTRUCTIONS COMPLETELY PRIOR TO INSTALLATION e BATTERIES PRODUCE EXPLOSIVE GASES Ensure no sparks or flames are present e Wear eye protection e Vehicles must be in NEUTRAL or PARK park brakes ON e Follow all vehicle manufacturer s instructions e Beware of moving parts e Battery Isolators are designed for negative ground alternator systems with batteries of the same nominal voltage e Batteries of differing voltages cannot be used FEATURES Heavy Duty Solenoid A heavy duty 85A solenoid made with a pla
3. or any other high temperature components Do not mount on the engine INSTALLATION CONNECTION To make the electrical connections all cables need to be made to the correct length using cable lugs and heatshrink Cable lugs should be crimped or soldered to the stripped bat tery cable and then protected with the heatshrink 1 Follow the diagram below to complete the installation OFF IGNITION SWITCH ACC RED FUSE BOX PIN CONNECTIONS VEHICLE FOR ROCKER SWITCH CIRCUITS EARTH SOLENOID S ROCKER SUPPLY SWITCH BLACK T RED BLACK a a m 12V STARTING 12V AUXILIARY BATTERY BATTERY G100 SURGE PROTECTOR 12V 85A SOLENOID To check for correct operation 1 With the ignition switch set at ACC Accessories or OFF the LED in the rocker switch should be off and the solenoid should be open batteries not connected in parallel 2 Turn the ignition switch to the ON position and then switch the rocker switch to ON the LED in the switch should illuminate and the solenoid should close connecting both batteries in parallel This can be checked with a continuity meter across the solenoids main terminals or can be confirmed by listening for a click as the solenoid closes 3 Turn the ignition switch to the OFF position or switch the rocker switch to OFF the LED in the switch will turn off and the solenoid will open batteries no longer cannected in parallel Note The Rocker
4. ted steel housing with 5 16 copper contact terminals provides the main control It parallels the two batteries when the ignition is turned on and provides the essential isolation between the auxiliary and main battery when the ignition is off Ignition Switch If the auxiliary battery is significantly larger than the starting battery the auxiliary may flatten the starting when the ignition is turned on not allowing the engine to start The ignition switch allows the isolator to be turned off from within the cabin to allow the engine to be started before activating the solenoid Surge Protection Provides surge protection for l a PART No DBS085K vehicles with electronic ignition systems VOLTAGE 12V only Suits all vehicles CHARGING CURRENT 85A 150A peak The solenoid isolator can be fitted to all 12V vehicle types CHARGE TYPE Parallel CURRENT DRAW VOLTAGE DROP SURGE PROTECTION _ Yes SG100 INSTALLATION MOUNTING 1 Disconnect the negative battery cable Earth from the vehicle s starting battery Note To prevent the loss of vehicle electronic memories radio presets amp security codes it is recommended that an Electrical System Memory Protector be used 2 Mount the auxiliary battery cradle and fit the auxiliary battery 3 Use the two supplied screws to mount the Solenoid in a convenient location as near to the main battery as possible Keep the Solenoid as far as possible from the exhaust manifold turbo
Download Pdf Manuals
Related Search