BAS screened.eps - Best Access Systems
Contents
1. Te ACCESS SYSTEMS Installation Instructions for V Series 83KV 93KV 85KV 95KV locksets Overview Figure 1 a Position template Note On steel frame applications align the horizontal centerline of the latch with the horizontal centerline of the strike preparation Figure 2 For uncut doors m Fold the template along the perforation and carefully place it in posi tion on the high side of the door edge bevel The suggested height from floor to the centerline of the lock is 38 For doors with standard cylindrical preparation m Looking through the hole from the opposite side of the door align the template so that you see the template outline of the 2 1 8 diam eter hole 1 Tape the template onto the door 2 Drill holes and install latch Note 1 Determine whether fabricated hollow metal doors are properly reinforced to support the lock If door reinforcement is not adequate consult the door manufacturer for information on proper reinforce ment Note 2 To locate the centerpoint of a hole on the opposite side of the door drill a pilot hole completely through the door For through holes it is best to drill halfway from each side of the door to prevent the door from splintering 1 Drill a 3 8 diameter hole through the door for motor wires 2 Bore the 2 1 8 diameter hole if not already drilled r Figure 3 Drill the 1 diameter hole into the edge of the door to meet the cen2. 13 2 Secure the battery compartment door with the security screw Tighten firmly Install inside and outside knobs or levers Figure 14 For the inside and outside levers 1 With the levers pointing toward the hinges push on firmly until seated 2 Tighten the trim mounting screws see Figure 11 3 Turn the levers to check for smooth opera tion For the inside and outside knobs 1 Push the knobs on firmly until seated 2 Tighten the trim mounting screws see Figure 11 3 Turn the knobs to check for smooth opera tion Caution Wires can interfere with the knob or lever operation BEST ACCESS SYSTEMS Indianapolis Indiana 13 Install strike plate Caution The deadlocking plunger of the latch bolt must not enter the strike plate The plunger deadlocks the latch bolt and prevents forcing the latch when the door is closed 1 Inalignment with the center of the latch bolt mortise the door jamb to fit the strike box and strike plate 2 Insert the strike box and secure the strike with screws provided a One half Door 7 thickness Door stop Door frame Figure 15 IC Install core and throw member 1 Install the blocking plate onto the throw member Caution You must use the blocking plate to prevent unauthorized access Blocking plate jm member 2 Insert the control key into the core and rotate 15 degrees to the right Figure 16 Figure 17 3 Insert the core and throw m
3. ST ACCESS SYSTEMS Indianapolis Indiana For proximity card electronic locks 1 Place the temporary operator card in front of the proximity reader as shown in Figure 20 The green light flashes and the locking mechanism unlocks Temporary operator card Proximity reader Figure 20 Note 1 f the lock s green light flashes but the lock remains locked make sure that the motor wires are connected Note 2 f the lock s green light stays on and the lock remains locked make sure that you re using the temporary operator card and not the temporary communication card Note 3 f the lock does not respond no lights no tones and the lock remains locked try one of the following solutions a make sure that the battery is connected a make sure that the outside wire harness is connected 2 Turn the lever or knob and open the door 3 Insert and turn the key to unlatch the door For details on programming the lock for access control refer to the V Series Intelligent Programming Software User Manual or the V Series Handheld Terminal User Manual
4. ember into the knob or lever with the control key 4 Rotate the control key 15 degrees to the left and withdraw the key Note Be sure to insert the correct throw member into the core six pin cores require the number 6 throw member seven pin cores require the number 7 throw member Caution The control key is a security key 15 Test lock To test the lock for proper operation use the temporary operator card or personal identifi cation number PIN that came with the lock This card or PIN is for temporary use only and once permanent cards or PINs have been pro grammed for the lock you should delete the temporary cards or PINs These temporary operator cards and PINs will only work on factory default V Series locks For magnetic stripe card electronic locks 1 With the temporary operating instructions facing toward you insert and remove the temporary operator card as shown in Figure 18 The green light flashes and the locking mechanism unlocks Temporary operator card Figure 18 Note 1 f the lock beeps and the lock remains locked make sure that you insert and remove the card in a smooth motion Note 2 f the lock s green light stays on and the lock remains locked make sure that you re using the temporary operator card and not the temporary communication card Note 3 f the lock s green light flashes but the lock remains locked make sure that the motor wires are connected T61918 R
5. evA 1777831 Note 4 f the lock does not respond no lights no tones and the lock remains locked try one of the following solutions a make sure that the battery is connected a make sure that the outside wire harness is connected 2 Turn the lever or knob and open the door 3 Insert and turn the key to unlatch the door For details on programming the lock for access control refer to the V Series Intelligent Programming Software User Manual or the V Series Handheld Terminal User Manual For keypad electronic locks 1 Enter the temporary operator PIN 99998 on the keypad as shown in Figure 19 2 Press 2 The green light flashes and the locking mechanism unlocks Figure 19 Note 1 f the lock beeps and remains locked make sure that you re using the tem porary operator PIN and not the temporary communication PIN Note 2 f the lock s green light flashes but the lock remains locked make sure that the motor wires are connected Note 3 f the lock does not respond no lights no tones and the lock remains locked try one of the following solutions a make sure that the battery is connected a make sure that the outside wire harness is connected 3 Turn the lever or knob and open the door 4 Insert and turn the key to unlatch the door For details on programming the lock for access control refer to the V Series Intelligent Programming Software User Manual or the V Series Handheld Terminal User Manual BE
6. rose liner in or out until the proper groove on the through bolt stud lines up with the hub face 13 4 Grooves on through bolt studs Hub face Pull rose locking pin to rotate rose Figure 6 Note 1 Make sure the locking pin fully locks into the rose liner T61918 RevA 1777831 Note 2 Locksets will fit door 1 3 4 to 2 1 4 thick A spacer is available for 1 3 8 doors See the enlarged view for the correct rose adjustment for these thicknesses m While feeding the motor wires through the 3 8 hole to the inside of the door insert the lock chassis from the outside Enlarged view geese aa Retractor ae N Z N i Latch tube Latch prongs tailpiece Chassis Figure 7 Caution Be sure latch tube prongs engage chassis frame and latch tail piece engages the retractor YM install through bolts and rose liner 1 Making sure the motor wires come through the notch in the 2 1 8 hole align holes in the liner with the holes prepared in the door Chassis hub Hr Through bolt Sleeve Inside liner Figure 8 Caution Make sure that there is clear ance for the motor wire between the rose liner and the door BEST ACCESS SYSTEMS Indianapolis Indiana 2 Install through bolts through the liner and door in the top and bottom holes 3 Tighten the liner onto the door with the through bolts 8 Make wire connections 1 Insert the bushings into the wire hole as
7. shown in Figure 9 and Figure 10 2 Feed the outside wire harness connector through the top wire hole Figure 9 Outside wiring harness Figure 9 3 Temporarily rest the trim on the door by inserting the trim studs into the stud holes From the inside of the door connect the motor connector to the mating connector from the circuit board Figure 10 A Bushing Disregard this wire for this assembly Figure 10 5 Making sure the connector is properly aligned connect the outside wire harness connector to the lower right circuit board connector in the inside trim Press firmly until fully seated 9 Throughbolt trim 1 Pull excess outside wire harness back through to the outside trim Combination mounting screw Standard mounting screw Figure 11 2 Position inside and outside trim onto the door 3 Making sure the trim does not pinch the wires secure the trim to the door but do not tighten with the combina tion mounting screw at the top mounting hole and with the standard screw at the bottom mounting hole 10 Connect battery 1 Connect the battery to the connector hanging inside the battery compartment Figure 12 2 Insert the battery pack into the battery compartment T61918 RevA 1777831 Install battery compartment door 1 Insert the tabs of the battery compartment door into its mating slots and swing closed Tons screw Tabs Figure
8. ter of the 2 1 8 hole if not already drilled Drill two 5 8 diameter holes for trim and one 7 8 hole for the wire harness Mortise the door edge for the latch face Install the latch and check the door swing Drill one 7 8 diameter hole for wires Note Latch tube prongs should be centered and should project into the 2 1 8 hole as shown in step 6 EI Install boring jig amp drill two 5 16 dia holes 1 Install boring jig KD303 onto the door and engage with latch tabs Make sure the front edge of the jig is parallel with the door edge 5 16 Dia Latch tabs 5 16 Dia 2 Center punch the drill points Figure4 T61918 RevA 1777831 BEST ACCESS SYSTEMS 1 Indianapolis Indiana 2 Drill 5 16 diameter holes halfway into the door 3 Turn the boring jig over and repeat steps 1 and 2 from the opposite side of the door Note Replace the boring jig after 10 door preparations Remove outside knob or lever 1 Remove the core and throw member see service instructions on reverse side Insert screwdriver blade here Knob keeper Figure eight core hole Figure 5 2 Inserta flat blade screwdriver into the fig ure eight hole and into the knob keeper 3 Depress the knob keeper Note You will not be able to remove the knob if the screwdriver blade is inserted too far past the keeper 4 Slide the lever off the sleeve Adjust to door thickness m Pull the rose locking pin and rotate the outside
Download Pdf Manuals
Related Search