Home

Soft Starter User Manual

1. 8 www vtdrive com VI drive 4 2 The external terminal Please see the diagram 4 2 ODDOODODDODDO By pass Time delay Failure Instantaneous stop Start up Public DCO 20mA output output output output Terminal are by pass output are used to control the by pass contactor They are normal open contacts and are closed when finishing starting The contact capacity is Ac250V 5A Terminal are programmable relay output it is set by FJ code They are normal open no power contacts Please see the detailed information in 5 3 item The contact capacity is AC250V 5A Terminal are fault output they will be closed when there are any fault matters happened to the soft starter or loose electricity while at normal case they are open The contact Capacity is AC25V 0 3A Terminal are Instantaneous stop input this terminal must be connected with terminal when the starter works normally But if these two terminals are both open the soft starter will stop and at this time the starter is at the state of fault protection Terminal can be controlled by the output contact of external protection dives and it is useless when the F12Key is set as O basic protection Terminal are start up or stop input There two ways of connections for your choose those are 3 wire connection and 2 wire connection Please see the diagram 4 3 N sno uezue suj sno uezuezsu
2. O If all the screws of terminals are twisted tightly 7 1 Set up electricity to test run As soon as the soft starter is electrify it displays the words of CSZPU or READY and the Ready lamp is light then you can press Run key to start Please come into FP item and input the current parameter according to the rated current on the label of Motor Having started the motor you should examine whether the running direction of Motor is correct or whether runs normally If not you can press Stop key or cut off the power to stop running If the soft starter starts badly you can check whether the starting mode you choose is fit for your motor Please see the detailed explanation at 7 2 the starting mode and application Ifthe Moment of starting is not strong enough you can change the starting voltage when the starting mode is voltage control or the limit current value when the mode is current control to strength the Moment of starting Do not open the up cover in case of electricity f there is any abnormal voice smoke or taste is very important for you to cut off electricity as soon as fast and check the reasons When the starter is in electricity or is starting the Fault lamp is lighting and screen displays Errxx at this time you had better check the Form 7 1 to get the reason Note When the temperature round is less than 10 C the starter should be preheated for 30 minute with el
3. 20 pon 2 Pump Piston 4 40 4 3 Compressor Lifting 60 4 3 5 Machine Stirring 2 50 3 Machine Screw Compressor 2 40 3 Screw Flight conveyor 20 40 2 Light load Motir 2 30 3 Traveling Belt 20 40 25 The Parameters above is for reference only 29 www vtdrive com
4. finishes t is the starting time Note It is normal that When the load equipments are light the starting time is less than the set time This mode generally fits for the occasions where the Motor must be started smoothly 7 2 2 Current limit to start The F9 item is set as 0 this starting mode is in use Diagram 7 2 isthe changing waveform of Motor current In diagram 7 2 r i A bs F the diagram I1 is the starting limit current value set When starting the output voltage rises quickly till the Motor current up to I1 value and not beyond this value The motor runs steadily in pace with therising of output voltage and when the motor runs to be the rated speed the output current will have a quick drop and down to the Motor rated current le value then the pass by contactor is working the stating operation finishes Note Itisnormal that When the load equipments are light or the limit current value youset is greater the Max starting current is less than the limit current value set This mode is often used in the conditions which requires strict limit to the current when starting 7 2 3 Torque control to start The F9 item is set as 2 or 3 this starting mode is 26 www vtdrive com VI drive infuse Diagrams 7 3 and 7 4 show the output changing waveform of Torque control mode When the static friction force in the state of heavy load is too stronger to start the motor can use this starting mode When starting the mot
5. time delay for motor This code is used It is used when the staring mode to is Limit current and the value set the start up 50 500 280 will be fixed as 400 when the limit starting mode is Ramp voltage to current value start 14 www vtdrive com VI drive This code is used to set the maximum working current of soft starter This code is used to set the the modes of input display This code is used to set the the under voltage protection This code is used to set the the under voltage protection This code is used to set the modes of starting This code is used to set 15 50 200 100 40 90 100 140 120 The 50 200 is basic on the nominal current of motor If the set value of this code over 200 the soft starter will be inverse time heat protection Set the detailed in Item 5 5 When the working voltage is under the value range 40 the soft starter will be in under voltage protection When the working voltage is under the value range 90 the soft starter will be in under voltage protection 0 Limi current to start 1 Ramp voltage to start 2 Torque control limit current 3 Torque control Ramp voltage 4 Ramp current to start 5 Double closed loop Set the detailed in Item 5 4 www vtdrive com VI drive This code is used to set 0 2 1 Set the detailed in Item 5 5 the parameter change This cod
6. V W Please seal the terminal switch insulation glue after finishing connect them The soft starter and its enclosures must be fixedly earthed During the maintenance and repair the input must be power 2 www vtdrive com VI drive 1 The General of FWI SS Series Soft Starter FWI SS series Soft Starter is new type start up equipment which integrates electric force and electron techniques computer technique and modern control theory It is the new generation product to replace the conventional Star delta Starter Self coupling voltage drop Starter and Magnetic control voltage drop Starter 1 1 The main function This Motor Soft Starter can reduce the starting current of Motor and the power distribution capacity to Motor effectively so it could save the cost It can reduce the starting stress of motor and other loading equipments so that lengthen their service life The function of soft stopping can solve effectively the surging problem of inertia system when stopping The conventional motor starting equipments can not realize it The perfect and reliable protection features can give the effective protection to the operator s safety as well as the motor and matched equipments The application of intelligent and network technique make the FWI SS type Soft Starter meet the high speed development of Electrical force automated technique effectively 1 2 The main characteristics Perfect design Pretty exter
7. 3 wire connection 2 wire connection Close K will start up Open K will stop 9 www vtdrive com VI drive Terminal 4D 2 are DC 0 20mA analogue output they show the current value of motor when real time working 20mA is full scale value and is four times than rated current of nominal power of soft starter while we can contact a 0 20mADC current meter to check The Max value of output load resistance is 3000 Note Please make sure that external terminals are in right connection otherwise the product may be damaged 4 3 The diagram of Main circuit connection Please see the diagram 4 4 iver har aaah ete tes analogy outpul I i a i i i ae 77 E a I s S i r instantaneous I ho 5 i a 4 i i I I CEE i a 1 i H O HES E I i I E i L 5 I a i pee a i E 0k ct fi i g i k m ao I Y Li PE 2 ai CF i k 8 m a ae i PL E B 4 iL rE it oo m i i ki Ta i a g a 5 z Lie By pass contactors 10 www vtdrive com VI drive 4 4 The communication interfaces RJ 45 is the standard web line socket DB9 socket has Rs485 and RS232 interfaces inside Please see the diagram 4 5 DB9 socket Q is RS485 i ge 6 O 6 is RS485 lt 2 is RS232 output N 3 LO 3 is RS232 input Bs 4 LO 4 is SV output limit current is SOmA 9 O 5 o 7 5 is earthed GND ae DOO are empty 1 Computer
8. E e e o e e cmne o o e e e E E e Note In the above form 1 is allowing O is forbidding For e example if you forbid any unexpected stopping or starting whether starting is running or in maintenance you can set the Numerical Value as 7 which means forbidding any starting or stopping operation If the External Control is used you must contact a NC button 19 www vtdrive com VI drive switch between the terminal and terminal otherwise the soft starter can not start up the motor FJ item is used to set the starting time of output of the Programmable relay As the following form Form 5 4 The Numerical Value of FJ item Starting time of output of out the Sending the ace order o Prgrammable 5 relay starting Sending Instantan Fault Finish happens re start ae out the Finish Starting Pass by eous order of stopping stop starting 5 6 Help message and explanation When the product is not starting or stopping or not at the set state you can press Yes key and come into Help menu then press the Up or Down key to choose the help message Please press Yes or Stop key to return Help message Form Message displayed Explanation AC380 That is the 3 phase power voltage is AC 380V 05 5 3 That is the Specification is AC380V 60Hz 5 5KW H1 E05 The fault message Err05 t
9. Err06 that means it is at that state of over load protection Note 1 only the operation is correct it will be with the voice when pressing the key Otherwise the operation is wrong e the control panel uses the super anti interference material so it can be state of 3 meters away 5 2 Parameters set and explanation The explanation for Parameter set codes Explanation for The range Ex factory Special explanation codes of value value This code can be used when the This code is used starting mode is set as Ramp to set the voltage 30 70 30 voltage to start and if is value Limit current mode the value will be fixed as 40 This code is used It is invalid in Limit Current to set the soft 2 60S 16S starting mode starting 13 www vtdrive com VI drive This code is used to set the soft If the code is set as O the 0 60S starting motor will staring mode time This code is used to set the time of 0 999S start up time delay By the count down way If set as 0 the starter will start up the motor Immediately without time delay Be used when you need or have This code is used to to Re start the motor for several set the Interval 0 999S times or Re start the motor after start removing the over heat protection time delay This code is used to time of Be used with programming 0 999S 0S programming relay output output
10. VI drive Soft Starter User Manual Safety Clauses 1 The general of FWI SS Series Soft Starter 1 1 The main function 1 2 The main characteristics 2 Code explanation and Check up before using 3 Usage conditions and Installation directions 3 1 The Usage condition 3 2 The Installation requirement 3 3 The Installation Directions 4 Connection and External terminal 4 1 The diagram connection 4 2 The external terminal 4 3 The diagram of Main circuit connection 4 4 The communication interface 5 Control panel and its operation 5 1 The operation of control panel 5 2 Parameter set and explanation 5 3 The functions of Programmable relay output 5 4 The function of Automatic Re start 5 5 Directions for other set items 5 6 Help message and explanation 6 Protection Functions and directions 6 1 Protection functions and theirs parameter 6 2 Protection classes and explanation 7 Test run and application 7 1 Set up electricity to test run 7 2 Starting modes and application 7 3 Stopping modes and application 7 4 Application example 1 www vtdrive com VI drive Safety Clauses In the process of using the soft starter please note the following Safety Clauses Please check this user manual carefully before using the product Only the technical person is allowed to install the product To be sure that the motor is correctly matched with the soft starter It is forbid to connect capacitors to the output terminals U
11. collector distribution control communication software 2 Device Net interface card and communication software 3 Device Net Mod bus Profi bus gateways 4 Others 5 Control Panel and its operation There are five working states of soft starter those are Ready Run Fault Start and Stop The control panel will show the current vault of motor when in the process of start or stop and it will show the set and help menu at other states 5 1 The operation of control panel Please see the diagram 5 1 Ready lamp Separationdot By pass lamp Failure lamp Data code HES Q READY jz F Pass AH LLO Ampere Percentage Second Function code 11 www vtdrive com VI drive Open state you should not press the run key until the ready lamp lights and show READY Time delay state When the ready lamp or fault lamp is shining it means it is interval time delay and when the Display screen shows dEXXX means staring time delay The Run or Stop key In the process of staring the panel shows XXXxX that is the value of start up current At this time only Stop key is in use And the lamps of ready run and fault are all dark and you can not come into the set and help menu state While in the process of stopping the panel shows XXXX that is the value of start up current At this time only Run key is in use and the lamps of ready run and fault are all dark and you can not come into the set and help menu sta
12. e is used to set This code is used to set Set the detailed in Item 5 3 the programming output This code is used to set the soft stopping 20 100 Set the detailed in Item 7 3 limit current value This code is used 0 the communication address 63 19 The rated current of motor to set is the same as the current nominal the rated current of motor current of Motor This code is used to set the motor Prohibition Set the detailed in Item 5 5 under load protection 16 www vtdrive com VI drive Note F7 the Max working current is basic on the nominal current of motor If you have no any operation for 2 Minutes after you come into the set state you will return from set state You can not set any parameters in the process of starting or stopping If you press the Yes key to open the soft starter you can make the set parameters recovery to Ex factory values 5 3 The function of Programmable relay output This function has two kinds of operation way those are Programmable time sequence output and output and Programmable state output When the FJ is set as 0 4 or 10 14 the programmable operation way is time sequence output As the following form The number set by FJ 0 10 4 14 The moment for Program output When sending the When beginning When at the start orderof starting the program output to start the of by pas
13. ectricity and then start 24 www vtdrive com VI drive Faults and Solution way Form 7 1 Explanation Reason and the solution way Any faults are removed such as under voltage The fault is removed over voltage over heat Now the Ready lamp is lighting and you can start the motor The External Please connect the External Instantaneous stop Instantaneous stop terminal terminal 7 with the Public terminal terminal is open terminal 10 The soft starteristoo The starter is started too frequently or the starter hot is not matched with the motor The starting time is i The starting parameteris set wrong or the load over long that is is over and the power capacity is not enough longer than 60S P Ene s Three phase unbalance Please check the 3 phase power or the Motor is normal The load is over or the Motor is not matched with the soft starter Err08 Running overload The load is over or the F6 FP item is set wrong Please check the voltage of Input power or the F Err09 Under voltage item is set wrong i Please check the voltage of Input power or Err10 Se er ae The parameters are set Please change the parameter correctly or you can Errll wrong press the Yes key to open the starter again to recovery the Ex factory values seuss DONET Explanati R and the solution x ation eason e SOLUTION Wa displayed p 4 S The load circuit or the Controlled silicon is Err12 Load short circuit na short ci
14. er to motor will be transferred from the by Pass Contactor to the Controlled Silicon of Soft Starter and the Output voltage of starter will be reduced gradually so that the Running Speed of Motor can be cut down smoothly in case of the Mechanical Shock The Output Ending Voltage is the same as the initial Voltage Soft stopping Mode can reduce or remove the Surge of the loading equipments such as the Water Pump You can set the Soft stopping limit current value through the FF item to reduce the Big current Shock to the Motor when stopping This limit current value is a Percentage 7 3 2 Free stopping Mode The F2 item is set as 0 this stopping mode is in use When using this mode to stop the motor the Soft Starter will cut off the connection to the By pass Contactor and forbid the Controlled Silicon outputting voltage as soon as receiving the order of stopping The motor stops gradually because of its Inertia Generally If the Soft stopping Mode is not necessary please choose the Free stopping mode to Length the service life of the soft starter This mode completely forbids the Instantaneous output in case the instantaneous big current shock to the Motor in special application state 7 4 Application Examples The parameters of the different loadings are different please see the Form 7 2 28 www vtdrive com Ramp voltage cet Initial Limit current The loading starting time to start Grinding Maching Centrifugal
15. est protection starting it can be protected most perfectly The protection classes and the time of heat protection Form Form 6 1 22 www vtdrive com VI drive Scio olanati Basic Light load Standard Heavy load The best Not silted AAE protection protection protection protection protection ws The grade of iii overload N 2 grade 10grade 20grade 10grade 2 H j j j IEC60947 protection A The grade of over current No 3 grade 15 grade 30 grade 15 grade protection Wat ca ianation Basic Light load Standard Heavy load The best Not P protection protection protection protection protection nie The multiple to h d 3 4 5314 5 3 4 5 34 The time of merai They are current overload The the typical dropping n values 2 4 5 2 3 1 5 23 12 7 5 46 23 15 23 12 7 5 dropping S Diagram 6 1 1 000 AER TN Se REAN Re Re Ee eee aes 100 SSSR 5S an Ge OE SSS SSS Sn a SSS s Th th e 20 grade oO cae ame cna Rein Sh in Renton A E Ro IR SS EE SS E eae ae ee de 0 5 SES SE CREME mec RO DR URNS 1 05 2 00 3 00 4 00 5 00 23 www vtdrive com VI drive Motor heat protection curve diagram Heat state 7 Test Run and Application Please do some examine before test running as following If the rated power of Soft Starter is matched with the Motor O If the Insulation of Motor is up to the requirement O If the Main Circuit Connection of Input or Output is correct
16. hat happened at the last time H9 E00 It says no fault happened Uer1 5 It says the software of the product is Ver 5 6 5 Note The message H1 H9 displayed means 9 faults kept that happened lately 6 Protection Functions and theirs explanation We make our soft starters have all kinds of protection functions to protect the soft starter and the motor using Please choose the correct Protection class and parameters according to your usage conditions Over heat Protection when the temperature inside soft starter is up to 80 C 5 C the starter will be into Over heat protection when be down to 55 C this 20 www vtdrive com VI drive protection removes O Input failure phrase protection the delayed time lt 3s Output failure phrase protection the delayed time lt 3s Three phrase unbalanced protection the delayed time lt 3s when the different current value among three phrases is more than 50 10 the protection be used O Starting over current protection the diagram 6 1 shows the protection time when the Current is more 5 times than the rated working current O Working over load protection the starter will be in inverse time thermal protection on Base of the Max working current of motor Set by F6 Item The diagram 6 1 s how Power voltage failure protection the delayed time is separately less than 0 5s or 3s when the power voltage is less than half of limited value or less tha
17. information Check up the type of product whether it is the right one you order 4 www vtdrive com VI drive FWI SS series Motor Soft Starter Input voltage 3 phase AC460V 60Hz Matched motor Date of produce Company Name Ex factory code SS SS Check any damage to the product because of the transport such as the spare parts are apart from the main body or the shell be damage etc Check others including the Certificate of Soundness and the User Manual 3 Usage condition and installation requirement It is strict rule for the users to use or install the soft starter according to the requirement otherwise it will be in bad result 3 1 The usage condition Power Supply City power self provided power diesel oil dynamotor 3 phase alternating current 380V 480V or 660V 10 50Hz or 60Hz The power capacity to the soft start must meet the motor starting requirement Motor Matched squirrel case asynchronous motor whose power is matched with the soft starter Starting Frequency The starting time is according to the loading equipments Cooling Mode Naturally wind cooling Protective Grade IP20 Environment Conditions when altitude is less than 2000m the temperature of the environment should be between 25 40 relative humidity should be less than 90 no vapor no flammable volatile corrosive gas No electric dirt indoor installation ventilated vibration is less that 0 5G Note Over more we can manufacture other ty
18. is 2 wire way you can Having got electricity and delay time for 60 seconds the soft starter will Re start automatically Having stopped because of any fault and delay time for 60 seconds the soft starter will Re start automatically the total number of times of automatic re start is n times n is set by FE item the function of automatic re start is effect only when getting electricity and 18 www vtdrive com VI drive opening again The soft starter has the protection function of under voltage so when the electricity be cut off and then get on again the soft starter will not Re start no matter which state the control terminals at in case of the danger to operator But if the Automatic Re start is allowed the Protection function of under voltage is no use 5 5 Directions for other set items You can use F8 item choose the Input way and Display Way As the following form Form 5 2 Numerical Value ie 0 l 2 3 of F8 item Input Way Input Current Input Percent Input Current Input Percent F6 F7 Value age Value age Running Display Display Display Display Display Way Current Value Current Value Percentage Percentage Note If the F6 F7 items input the percentage numerical value the percentage is the current Percentage set by FP item FD item used to set the control ways of soft starter As the following form Form 5 3 rman o fo a e e e mm i e e e E ee sarana o
19. n the set value O Over voltage protection the delayed time is separately less than 0 5s or 3s when the power voltage is move than 130 if limited value or more than the set value Loading short current protection when the current is more 10 time than the motor rated current it will be short current and then be in short current protection the time is less than 0 1s O The time parameters above is from the time receiving the message to the time sending out the protection message They are for reference only If you need any 21 www vtdrive com VI drive other protection functions please contact with us 6 2 Protection classes and explanation According different usage conditions GJR8 Soft Starter has five protection classes as following a basic protection b light load protection c standard protection d heavy load protection e the best protection Basic protection includes the protection functions of over heat short current protection and input failure phrase protection when starting but no protection of internal connector instantaneous shop we can se he protection glade when the motor is no need to be stopped urgently such as fire pump The light load protection standard protection and heavy load protection all have the every protection function of soft standard The difference among them is the surges o Mot overload heat protection See the diagram of 6 1 and Form 6 1 When the motor in the b
20. nal shape and structure perfect and unique functions simple and 3 www vtdrive com VI drive reliable operation every technological is made in the best design Reliable and high grade quality This product is designed according to the computer analog test has the best electromagnetic compatibility It is proved high quality by the high temperature ageing test and jigging test which done before the products out of factory Complete and perfect protection functions Such as offset voltage protection failure voltage protection over voltage protection Motor overheat or starting time over long protection input or output failure phase and three phase unbalanced protection over current over load and short current protection unbalanced protection over current over load and short current protection Having the decision making intellectual property of the product Including exterior designing patent decision making software copyright the starting and protection techniques of Motor and the technology of detecting and debugging The best service The reliable function and quality is the basic of the best service Even more we can supply the special designing and functions of product matched to your need and the timely and perfect usage consulting service 2 Code explanation and Check up before using Please check up the products before using if in some problems please do not hesitate to contact us with any request for additional
21. or needs a very high voltage for a limited time to remove the static friction force of heavy load then you can use the Ramp voltage mode or limit current mode to start the motor diagram 7 3 diagram 7 4 oe Un100 Si eae ul i 2 0 1100ms T Note This mode will cause big current shock to the motor so if the Ramp voltage or Limit current mode can be used please had better not use the Torque control to start 7 2 4 Ramp Current to start The F9 item is set as 4 this starting mode is in use Diagram 7 5 shows the Output current waveform In the diagram 7 5 diagram I1 is the current valueset by F6 item and T1 is Time value set by F2 item This starting mode has very stronger speed up ability and is suit for the Bipolar Motors and it can reduce the starting time 7 2 5 Double closed loop Both Ramp Voltage and Limit current to start The F9 items set as 5 this starting mode is in use This starting mode uses the control mode of Ramp voltage starting and Limit current starting Double Closed Loop 27 www vtdrive com VI drive circuit it is a composite starting mode The Output voltage waveform is changed as Motor and the load equipments 7 3 The Stopping Mode and application The soft starter has two Stopping Modes those are Soft stopping mode and Free stopping mode 7 3 1 Soft stopping Mode The F2 item is not set as 0 this stopping mode is in use When using this mode to stop the motor the supply pow
22. ot be more than this value 6 www vtdrive com VI drive w2 ZH o o o The External shape and installation dimensions of 75KW 560KW Installation oO Q C n C pam Oo x lt LL dimensions mm dimensions mm Specifications kg ae ere FWI SS3 075 FWI SS3 090 FWI SS3 115 FWI SS3 132 FWI SS3 200 FWI SS3 250 FWI SS3 280 FWI SS3 320 FWI SS3 400 www vtdrive com VI dri drive 370 525 370 525 FWI SS3 500 370 525 Il a le lel Le The FWI SS Soft Starter has three types of connection as following Main circuit connection it contains the wiring of 3 phase source input the output to motor and the pass by contactor connection External terminal connection that is the wire comes from twelve external terminals which including control signal and analogue output signal Communication connection there are two communication interfaces those are RJ 45 standard web line socket and Db6socket which are connected to computer 4 1 The diagram connection see the diagram 4 1 3 phase power input Circuit Breaker QF Computer communication interface By pass contactor KW Motor Soft Starter Operation control Panel 12 extemal terminals Squirrel cage 3 phase asynchronous motor
23. pe soft starters which are used in special conditions such as 5 www vtdrive com VI drive explosion proof type soft starter low temperature type soft starter or high voltage type soft starter 3 2 The installation requirement The direction and distance of installation In order to make sure that the soft starter be in good draft and heat dissipation please install the product in vertical direction and be sure the spare around the product is enough See the following diagram 3 1 and 3 2 Ifthe soft starter is installed in a box please note that the draft is very good as well as the above notes See the following diagram 3 3 3 3 The Installation Dimensions The External shape and installation dimensions of 5 5KW 55KW External shape Installation Specifications dimensions mm dimensions mm N Ei N N N O D O N ico N N N O O O O O O O O A oo o1 _ O O N N N N A oo o FWI SS3 5d5 5 5 FWI SS3 7d5 FWI SS3 011 A R wo ao NIN NTN Nini ni ni a So Oo oO _ oD ro _ N N K D O O N N N 3 A oe O O N ice N N N z FWI SS3 037 37 Note The rated power of motor in the above form is the maximum rated value N N 3 O O N ico N N A A oo S o1 N N O N N A w S7 N N O N N generally the values of matched motor should n
24. rcuit The Connection of Err13 Automatic Re start is wrong Err07 Starting over current The external terminals is not connected according the 2 wire way The connection of E Sa The reason is that the circuit of external stop external terminal is s terminal is open wrong Note Some faults happened are interrelated so please check the reasons completely Note When the motor starts successfully the pass by lamp will be lighting that means the pass by contactor is running At this time if the contactor is not 25 www vtdrive com VI drive closed the motor will stop running so you can check whether the connection to the pass by contactor is right 7 2The starting mode and application There are six starting modes for the user to choose according the motor and load equipments as the following 7 2 1 Ramp voltage to start The F9 item is set as 1 this starting mode is in use Diagram 7 1 shows the Qutput voltage waveform In the diagram 7 1 diagram the Ul is the initial voltage value of starting When starting if the motor current is not more 400 than the rated current the Output voltage of soft starter will up tobe Ul andthen the Output voltage rises gradually till to the height of rated voltage Ue The motor runs stea dily in pace with the rising of voltage and as soon as the voltage is up to be Ue the motor runs tobe the rated speed and the pass by contactor is closed the starting operation
25. s program output operation the program output When sending the order of stopping the program output When finishing the operation of stopping the put If need programmable relay output time delay the delay time is set by F4 code eWhen the FJ is set as 5 9 or 15 19 the programmable operation way is time sequence output As the following form 17 www vtdrive com VI drive The number oe 5 15 6 16 7 17 8 18 9 19 set by FJ The output i o 99 Operation By pass state Error state Ready state Starting state state operation state showed The way of programmable state output is used to show the working state of soft state and under this way the F4 code is un useful The ex factory value of FJ code is 7 showing the ready state of soft starter and at this time the motor can be started up when the programmable output is in fault state the faults m gt gt mean the fault of motor such as fault of Err05 Err06 Err12 Err15 and they are different form the faults come from the terminals output When FJ gt 9 the reset state of programmable output is normal closed that is inverse phase output 5 4 The function of Re start When the FE item is not set as 0 the Automatic Re start function is in use This function is affective only the External Control connection is 2 wire way and is not controlled by the FD item External Control allowed When it
26. te The Set key Press Set key to come into the Set Menu and now the panel is showing FX XXX Please press Set key again and Colon is shining then you can change the Parameters under the Colon you need If you want to keep the Parameters changed Please press Yes key and if you do nor want please pressing the Set key until the Colon stops shining then the Parameters are former Having finished the above operation please press the Yes key to return or Stop key to return directly The Yes key Press the Yes key directly you will come into Help Menu and the panel shows HX XXX When you finish reading the Help Menu you can press this key again or Stop key to return This key not only can be used to keep the Parameters when you set the parameters you need but also be sued as Returning 12 www vtdrive com VI drive The Up and Down A A key In the Set Menu you can press these two keys to choose the Function Code you need when the Colon is not shining and can choose the Parameters under the Colon when Colon is shining lt is the same as the operation in Help Menu When the Pass by lamp is lighting and the Display Screen shows AXXX which means the operation current value of motor now you can press Up or Down key and the Screen will PXXXX or HXXXX in t u n P X XXX means the apparent power of motor HXXXX means the over load heat balance coefficient if this value is more than 100 the Screen shows

Soft Starter User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents