Owner`s Manual - Spectrum Industries, Inc.
Contents
1. Note Leave enough slack in the cords and wires from the rack cabinet to pull the rack cabinet out from the lectern Cords and wires 4 from Rack Cabinet Rack Cabinet Bottom view 2 Grommets for floor power access Figure 8D SPECTRUM INDUSTRIES INC 0118857 Page 11 of 18 Caster operation 1 Lock the brake levers to lock movement of the casters Two instructor side casters only Figure 9 2 Toresume operation lift up on brake levers Brake lever Note The skirt should be removed to prevent skirt damage if the lectern will be moved over large floor transitions or thresholds Moving and parking the lectern e Before moving unplug and secure all power cords e Close and lock doors e Remove any items from the top of the worksurface e Unlock the casters e Push slowly and carefully Do not move over uneven or irregular surfaces e Do not allow children to move e Lock the casters after moving e Do not park unit in areas of heavy traffic e Do not run power cords across hallways classrooms or other areas where they will be walked on e Do not leave unit unattended in areas where children have access e Keep doors closed and locked whenever unit is unattended or parked e Keep casters locked whenever the lectern is unattended SPEC AAL2. Note The Freedom XRS Elite Lectern is not designed for use with cord reels or surface mount cord reel accessories Note CPU slings cannot be used with Freedom XRS Elite lecterns because of mounting and ADA compliance considerations If a CPU is necessary it can and should be installed into the rack cabinet using a rack mount shelf See website for rack mount accessories Use caution when raising or lowering lectern A CAUTION amp Always unplug lectern before working under the work surface or inside rack cabinet Do not place anything under worksurface when operating lift Use caution when raising or lowering the worksurface SPEC LARUM INDUSTRIES INC 0118857 Page 2 of 18 Assembly Setup 1 Unloading lectern Note Upon receiving lectern inspect packaging for damage To report informa TYKI tion regarding damages please call 1 800 235 1262 within 15 days of receipt Tools Required 1 Cut and remove banding using a utility knife scissor or other cutting tool 2 Remove steel corners by removing screws using Phillips screwdriver 3 Open top of box by unfolding flaps 4 Remove plywood ramp from package Place on floor next to the pallet Figure 1 This will be used to unload the lectern off the pallet 5 Remove cardboard sleeve by lifting it up and over the lectern 6 Remove protective shrink wrap from lectern using a utility knife scissor or other tool Be careful not to damage the lecte
3. 3 cm x 27 3 D 69 3 cm x 28 8 H 73 2 cm Weight capacity 25 Ib 11 4 kg Unit weight 65 Ib 29 5 kg Dimensions 20 W 50 8 cm x 12 5 D 31 8 cm x 4 H 10 2 cm Unit weight 10 Ib 4 54 kg Note The keyboard tray protrudes 3 9 10 cm below the work surface If the lectern is used for ADA use a higher adjusted worksurface is necessary to provide ADA leg clearance SPEC LARUM INDUSTRIES ING 0118857 Page 13 of 18 Cove Power Module 99044 Overbridge Insert Panel Blank 96504 Overbridge Insert Panel with cutouts 96504mod e Two power receptacles e For overbridge version only e Two USB charge ports not data compatible e Contact Spectrum to specify cutout size s and location s e Thumbscrew clamps e Overbridge not available separately e Requires worksurface cutout e Includes two 2 grommets with covers e ETL listed e Customer installed e Customer installed Cutout required 5 25 W 13 3 cm x 2 D 5 1 cm mounts to surface thicknesses up to 1 5 Power cord 9 274 cm with 90 flat plug with 45 rotation Power receptacles 12A 120 VAC spill resistant USB charging ports 2 1A 10 5W Dimensions 6 W 15 2 cm x 2 5 D 6 35 cm x 3 18 H 8 1 cm Unit weight 2 3 Ib 1 kg See spectrumfurniture com for the latest available flat panel monitor arms and rack mount accessories 0118857 Page 14 of 18 SPEC dL HAN INDUSTRIES ING Electric leg information A Warning Failure to compl
4. EU markets e Persons who do not have the necessary experience or knowledge of the product products must not use the product products Besides persons with reduced physical sensory or mental abilities must not use the product products unless they are under surveillance or they have been thoroughly instructed in the use of the apparatus by a person who is responsible for the safety of these persons e Moreover children must be under surveillance to ensure that they do not play with the product e tis the operator s responsibility to ensure that there is free space for the application to move without risk for the operator or bystanders before operating the application Misuse Do not overload the actuators this can cause danger of personal injury and damage to the system e Do not use the actuator system for lifting persons Do not sit or stand on a table while operating risk of personal injury Do not use the system in environments other than the intended indoor use Repairs In order to avoid the risk of malfunction all DESKLINE repairs must only be carried out by authorised LINAK workshops or repairers as special tools must be used and special gaskets must be fitted Lifting units under warranty must also be returned to authorised LINAK workshops Warning If any of the DESKLINE products are opened there will be a risk of subsequent malfunction Warning The DESKLINE systems do not withstand cutting oil CB
5. and to no other per son or legal entity No Spectrum dealer distributor agent or employee is authorized to make any modification or addition to this warranty NOTWITHSTANDING ANYTHING TO THE CONTRARY SPECTRUM WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE FOR INDIRECT OR LIQUI DATED DAMAGES INCLUDING CONSEQUENTIAL INCIDENTAL AND SPECIAL DAMAGES IN NO EVENT SHALL SPECTRUWM S LIABILITY WHETHER UNDER CONTRACT OR WARRANTY IN TORT OR OTHERWISE EXCEED THE PURCHASE PRICE RECEIVED BY SPECTRUM FOR THE PRODUCT AT ISSUE AND RECALL ACTION EXPENSES SPECTRUM SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR LIABILITIES WHETHER ARIS ING OUT OF BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE AND STRICT LIABILITY OR OTHER THEORIES OF LAW WITH RESPECT TO PRODUCTS SOLD OR SERVICES RENDERED BY SPECTRUM OR ANY UNDERTAKINGS ACTS OR OMISSIONS RELATING THERETO Our Customer Service Department is ready to provide immediate attention to any questions comments or concerns They are available to answer your calls Monday through Friday from 7 am to 5 pm CST In addition your product comments or concerns are welcome via e mail at soectrtum spectrumfurniture com Warranty Table effective 1 1 2015 Adjustable Crank Electric Desk Legs e 1 Year Flat Panel Desk Gas Cylinders Chairs Adjustable Height Chair Parts including frames gas 7 Years cylinders wood and plastic parts control handles casters Adjustable Height Chair Upholstery 2 Years
6. cm o 0 564 1 44 cm 7 yh Worksurface 4 964 12 61 cm Note The Overbridge Control Console has been designed for many of the cur rently available controllers on the market however modified cutouts should be re viewed by Spectrum to ensure clearance of brackets keyboard slides or other 5 272 objects under the worksurface 13 39 cm Contact Spectrum to specify cutout size s N Channel and location s 8 2923 21 06 cm SPECTRUM Figure 7 INDUSTRIES INC 0118857 Page 9 of 18 Wiring Diagram Actuator Actuator Up Up Dowr Done i Control box Note Power cord can be plugged into a power strip not included inside lectern To wall outlet Note A separate power strip is recommend ed not included to plug the control box and other power plugs into The power strip can be located in the cord channel or lower side of the lectern and plugged into a wall outlet Control box Note Extending the worksurface will provide access to the cord channel and control box Control button connection Actuator plug plugs SPECTR om 0118857 Page 10 of 18 INDUSTRIES INC
7. or flip up the shelf press and hold the levers under each folding shelf bracket at the same time while slowly lowering or raising the shelf Do not exceed a maximum of 50 Ib of weight on the shelf Do not move the unit while the shelf is in the horizontal position 1 If your shelf is not already installed attach the folding shelf brackets to the preferred side of the lectern with 3 8 32 x 1 2 PH thread cutting screws Figure 6B Do not tighten completely yet 2 Seta shelf shim on each bracket then place shelf on top Align all holes and secure with 8 8 x 1 PHSM screws 3 Tighten all screws securely Release lever press here 4 j Al Folding shelf P d W A bracket m 8 32 x 1 2 PH thread cutting screw A CAUTION Q Keep clear of pinch points during shelf movement Do not exceed 50 Ib 22 68 kg of weight on shelf Note Power and communication wiring for docu ment cameras laptop computers and or projec tors placed on the flip up shelf should be routed on top of the audience side of the shelf Use of the shelf grommet hole for wiring will result in pinching of the cords when the shelf is folded SPEC aid LIAN INDUSTRIES ING 0118857 Page 7 of 18 Overbridge insert panel optional 4mm hex wrench To remove the overbridge insert panel remove the 2 1 4 20 x 35mm JC bolts with a 4mm hex wrench and lift out the panel Figure 7A Measuring device Dr
8. the unbalanced loads Down button Press and hold the Down button again and hold for 35 45 seconds The actuators have now been reset and the worksurface can be adjusted normally Solution 2 Detach one of the actuators from the worksurface Lower the lectern all the way down Re attach the actuator to the worksurface A WARNING amp Be sure the lectern movement does not interfere with objects or people Do not place any items under the lectern worksurface SPEC LARUM INDUSTRIES ING 0118857 Page 17 of 18 WE WILL MAKE IT RIGHT FOR YOU Spectrum is committed to provide complete customer satisfaction Each of our products is manufactured from the best materials available and each product is stringently monitored throughout the production process through our P A C E program Product Assurance to meet Customer Expectations We expressly warrant that Spectrum products will be of good quality and workmanship and free from defect for the period set out in the warranty table below from the date of delivery This warranty shall not apply to defects or damage resulting from misuse abuse neglect improper care modification or repair not authorized by Spectrum or any other cause outside the control of Spectrum Spectrum will at its sole option either repair or replace the defective product This warranty is exclusive no other warranty written or oral is expressed or implied This warranty is given by Spectrum to Buyer
9. D4 LINAK G WE IMPROVE YOUR LIFE Sundby DESIGNED IN DENMARK Power Item CBD4H00040A 409 Date 130521 Uin 120V 60 Hz Pin 600W U Out 12 24 V Op 10 Max 2 min 18 min S W P N 0077474 Ver 1 12 A SOAGCEY DOMET INSULATED WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS NOT TO BE OPENED BY UNAUTHORIZED PERSONNEL P O 110125 ASSEMBLED IN CHINA 01 i SAY File 151104 SPEC dL HAN INDUSTRIES INC 0118857 Page 15 of 18 Misc on the DESKLINE DL5 DL6 system This system is a DESKLINE system developed for desks and for indoor use in offices Do not use it in industrial kitchens or in other enviroments that have to be cleaned with aggressive detergents Do not bolt the legs to the floor so that free movement is prevented This could cause serious damage to the legs in fault situations Warranty There is a 36 months warranty on the DESKLINE products against manufacturing faults from the production date of the individual products see label LINAK A S warranty is only valid in so far as the equipment has been used and main tained correctly and has not been tampered with Furthermore the system must not be exposed to violent treatment In the event of this the warranty will be ineffective invalid For further details please see LINAK A S ordinary conditions of sale Maintenance Clean dust and dirt on the outside of the system at appropriate intervals and inspect them for da
10. In Stock Upholstery 2 Years Graded In Fabrics and Customer Owned Material No Warranty Height Adjustable Columns and Lifts 1 Year General Use Casters Electrical including timers and LINAK actuators Keyboard Mouse Trays Flat Panel Monitor Arms e Flat Panel Monitor Arm General Parts e 5 Years e Flat Panel Monitor Arm Gas Cylinders e 2 Years Desks and Lecterns e Computer Desk Chassis e Cart Chassis 10 Years e Lectern Chassis 925 FIRST AVENUE CHIPPEWA FALLS WI 54729 800 235 1262 715 723 6750 WWW SPECTRUMFURNITURE COM 0118857 Page 18 of 18
11. L INDUSTRIES ING 0118857 Page 12 of 18 Accessories Available separately after initial configured purchased Customized Logo Panel 55389 Flip Up Shelf 55333 e Attaches to audience side of lectern panel removal required to install e Shelf hinges lock into place in the upright position e 32 25 W 81 9 cm x 11H 27 9 cm e Shelf installed level with worksurface e To get panel customized contact Spectrum for details e Customer installed e New logos require a first time logo charge e Customer installed Weight capacity 50 Ib 22 7 kg Dimensions 15 25 W 38 7 cm x 24 625 D 62 5 cm x 1 H 2 54 cm Unit weight 20 Ib 9 1 kg Rack Cabinet 55297 Keyboard Tray 55334 e One rack cabinet attaches to the left or right side of the XRS Elite lectern e Installed in left or right position opposite rack cabinet using pre drilled holes e Locking door can be flipped to be hinged left or right e Tray can be installed and used as a keyboard tray or flipped and used as a e Locking side hatches storage drawer using pre drilled mounting holes under the worksurface e Removable back panel e Wire management slots in tray e Acrylic panel in door e Max 1 tray per Freedom XRS Elite e Customer installed e Customer installed Front rack rail 14RU Slides Pull out 8 20 3 cm Rear rack rail 10RU Height adjustability 1 2 54 cm 2 375 6 cm Dimensions 20 6 W 52
12. SPEC Hitt IAN Owner s Manual INDUSTRIES INC Freedom XRS Elite Lectern XRS Elite with surround keyboard tray r XRS Elite with overbridge keyboard tray and rack cabinet installed on left and rack cabinet installed on right shown retracted shown extended A Important A Before using this product e Read this manual e Comply with all safety and operating instructions e Ensure all parts and correct quantities are included Any parts damaged during shipment must be reported within 15 days of receipt To report information regard ing missing parts or damage to purchase parts or accessories or if you have any questions please contact us Thank you for purchasing Spectrum products Spectrum Industries Inc 925 First Avenue Chippewa Falls WI 54729 USA 800 235 1262 715 723 6750 www spectrumfurniture com 0118857 Page 1 of 18 Important Safety and Care Instructions e Read this owner s manual before assembly or operation Do not allow children to move the lectem e Proceed slowly and carefully when moving the lectem For indoor use only Do not install or store the lectern where it will be exposed to moisture Do not block the ventilation openings e Avoid uneven loading of the equipment into the lectern Uneven weight distribution could cause the lectern to tip when the lectern is moving e Do not allow anyone to sit stand or climb on the lectern e Use a damp soft cloth or sponge w
13. e sure that the voltage of the control box is correct before the system is connected to the mains System connection The individual parts must be connected before the control box is connected to the mains See the User Manual for LINAK actuators if necessary During operation e If the control box makes unusual noise or smells switch off the mains voltage immediately e Take care that the cables are not damaged Unplug the mains cable on mobile equipment before it is moved e The products must only be used in an environment that corresponds to their IP protection Misc The actuator system has a sound level below 55dB A in typical applications Updated manuals and declarations can always be found here www linak com deskline DL6 LINAK G WE IMPROVE YOUR LIFE item No DL6000A00650560 Prod Date 2006 05 09 Max Load 800 N mae Rate 18V 10 Amp Cycle iim Men 2 win inh min N A sonneL Z TO T OA HCE 23456 0 MADE BY LINAK A S DENMARK A Only for EU markets e This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved e Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision A Only for Non
14. esk The 40 kg are needed to activate the anti collision function Situations where the anti collision does not work There are situations where the anti collision will not be activated These situations are e If the collision happens during the initialisation phase e If the collision happens within the first 1000 msec or after the control button has been released e If the collision happens between the floor and the table and the load on the desk the weight of the legs are lower than 40 kg e Ifthe collision happens over too long time e g if the collision is with a soft object SPEC TRUM INDUSTRIES INC 0118857 Page 16 of 18 Freedom XRS Elite Troubleshooting Guide Worksurface will not operate Be sure control box is plugged into a live circuit Make sure all electrical connections are securely plugged into the control box Loose electrical connections See wiring diagram on p 9 for reference Raise the worksurface by pressing the up button 7 Remove any items under the lectern worksurface 3 Reset the lift mechanism see below for procedure Solution 1 Object encountered under the lectern worksurface Reset Procedure Unplug then re plug the power cord into a wall outlet Make sure all lift mechanism wire connections are in place and secure Remove anything located under the lectern worksurface Misaligned actuators due to Press and hold the Down button until the lectern stops moving Release
15. hough this lectern utilizes an anti collision feature that briefly stops and reverses the worksurface motion in the event of an obstruction use caution when raising or lowering Do not sit at under or on the worksurface when operating the lift mechanism and be sure lectern movement does not interfere with objects or people Use caution when raising or lowering the worksurface SPEC LARUM INDUSTRIES ING 0118857 Page 4 of 18 3 Install 3 piece Skirt Note The skirt has been designed to be installed tool free with the lectern upright Do not tip the lectern to install 1 Position the audience side skirt as shown and hook the 3 pre installed screws into the 3 keyhole slots Figure 3A 2 Pull the skirt back toward audience side to lock the screws into the keyhole slots Keyhole slots VG Freedom XRS Elite Lectern Audience side skirt 3 Position each side skirt as shown and hook the 2 pre installed screws into the 2 keyhole slots Figure 3B 4 Pull the skirt back toward audience side to lock the screws into the keyhole slots The short flat skirt edge should contact the audience side skirt 5 Apre installed magnet on each skirt will secure the assembly to the lectern base Make sure the magnet on each side skirt is fully seated and contacting the base Each skirt should be level Figure 3C Right side skirt Pre installed magnet i Audience side
16. ill bit ay VA Pencil To make cutouts in the insert panel optional Identify all location s and sizes for controller s or electronics while making sure all devices fit within the maximum cutout space available in the overbridge panel See Figure 7B 7C See specifications for cutout clearances B Locate and mark the exact cutout area s on the panel Note Using masking tape on cut lines will minimize laminate chipping while cutting Tools Required Jigsaw Carefully make the cutout s in the overbridge panel using a jigsaw or router or Router Install controller s electronics into panel Maskin Re install the overbridge panel and secure with 2 1 4 20 x 35mm JC bolts tape g amp cmr 1 4 20 x 35mm JC bolt 1 4 20 x 35mm JC bolt Overbridge panel Note Blank overbridge panels require the cus tomer to make necessary cutouts with a jigsaw or router This has a moderate difficulty rating so experience and skill with tools is required SPEC LARUM INDUSTRIES ING 0118857 Page 8 of 18 Freedom XRS Elite Lectern overbridge insert panel blank flat view 0 9374 2 38 cm L129 ey cm 22 ia cm Max cutout area 0 9374 ml 238 cm 4 2813 18 6875 4 2813 10 88 cm 47 47 cml 2725 10 88 cm 69 22 cm Overbridge 1 2 Section view B B 3 05 cm 9 22 86 cm 7 236 4 691 18 38 cm 11 92
17. ith mild soap or detergent solution to clean dirty surfaces Do not use harsh solvents or abrasives e This lectem is intended for institutional use It does not have any user serviceable parts or user maintenance requirements If servicing is necessary please contact Spectrum Industries for assistance Awami g Relocating audio and or video equipment to furniture not specifically designed to support audio and or video equipment may result in death or serious injury due to the furnishing collapsing or over turning onto a child wami g Death or serious injury may occur when children climb on audio and or video equipment furniture A remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on to the child Electrical Safety Do not plug the power cord into an extension cord Inspect power cords for damage before each use Do not use power cords that are damaged Unplug power cord from electrical outlet by gripping the cord Do not unplug the power cord by pulling only on the cord Do not step on drive over drag or place objects on the power cord For added safety plug the lectern into a grounded outlet controlled by a GFI Ground Fault Interrupter circuit breaker Electrical devices are not toys Children are often unaware of the hazards associated with electrical devices This lectern must always be used by adults or with adult supervision
18. ive is ensured by means of software in the CBD4 CBD5 CBD6 that also takes account of oblique load on the desk Soft start and stop are also part of this software which ensures a soft start and stop when adjusting the desk Application of the DESKLINE DL5 DL6 system Irrespective of the load the duty cycle 10 6 min hour or max 2 min at continuous use stated in the data sheets must NOT be exceeded as this will result in a superheating of the motor the brake and the spindle nut Exceeding the duty cycle will result in a dramatic reduction of the life of the system The DESKLINE DL5 DL6 system range contains the following products e 1 control box CBD4 CBD5 CBD6 e 1 single DL5 DL6 or 2 3 or 4 parallel e 1 exchangeable mains cable e 1 2 3 or 4 motor cables e 1DP1U DPF1M if memory function is required DP1C WDPL DPT DPF1C if memory function and display is required or 1 DPA DPB DP1K DP1V DPF1K if only up down is required Electrical connection of the DL5 DL6 system The DESKLINE DL5 DL6 system is to be connected as shown on figure 4 Each DL5 DL6 is to be connected to the sockets on the control box by means of the motor cables which have an 6 pin plug in each end Finally the mains cable is to be mounted and power switched on ng Please note that the control box must only be connected to the voltage stated on the label CBD4 CBD5 CBD6 with earth The CBD4 CBD5 CBD6 earth cable to be mounted on the desk constructio
19. mage and breaks Inspect the connections cables and plugs and check for correct functioning as well as fixing points Service of double insulated products Class Il A Class Il or double insulated electrical appliance is one which has been designed in such a way that it does not require a safety connection to electrical earth US ground The basic requirement is that no single failure can result in dangerous voltage becoming exposed so that it might cause an electric shock and that this is achieved without relying on an earthed metal casing This is usually achieved at least in part by having two layers of insulating material surrounding live parts or by using reinforced insulation There is no earthing grounding means provided on the product and no earthing ground ing means is to be added to the product In Europe a double insulated appliance must be labelled Class II double insulated or bear the double insulation symbol a square inside another square Servicing a double insulated product requires extreme care and knowledge of the system and is to be done only by qualified service personnel Replacement parts for a double in sulated product must be identical to the parts they replace K tk d f The cleaners and disinfectants must not be highly alkaline or We acidic pH value 6 8 Description of the DESKLINE DL5 DL6 system Each DESKLINE DL5 DL6 lifting units is equipped with a motor and parallel memory dr
20. n typically the top frame in a way that ensures good electrical contact The function of the earth cable is to earth the desk and ground static electricity The earth connection does not protect other electrical products A CBD4 CBD5 with mains cut off non ZERO models If the power cable is damaged it has to be replaced by an authorized LINAK service centre to avoid any danger DL5 DL6 cable hook for cable relief Ha cable Ze RA DP WDPL DL5 DL6 N Anti Collision The function anti collision is an option for the standard CBD4 CBD5 CBD6 advanced control box software 0077432 version 1 66 and later A system with anti collision can limit material damages on a desk if a collision with a solid object should occur DL5 DL6 Method of operation When the DL DB s are running the CBD4 CBD5 CBD6 monitors the current consumption on each channel using a special algorithm If the current consumption on one channel is increased more than a predefined slope a collision is assumed and all channels are stopped immediately and all DL DB s will start to run in the opposite direction approx 50 mm This return drive is done automatically and continues with or without any control key pressed for max 2 5 sec The anti collision sensitivity is different in upward and downward direction Upwards the force is approx 20 kg Downwards the load will be approx 40 kg the load on the DL DB the desk what is on top of the d
21. rn when cutting shrink wrap 7 Remove Styrofoam corner blocks 8 Using ramp carefully lower the lectern off the pallet onto the floor SPEC LARUM INDUSTRIES ING 0118857 Page 3 of 18 2 Lectern lift mechanism initial setup operation and reset procedure Preparation e Read all instructions before operation e Make sure lectern is plugged in using the 15 foot 15 amp power cord e Locate the Up and Down control buttons Control pad is located on the instructor side under the worksurface front edge on opposite side from rack cabinet e Keep clear of pinch points during worksurface movement Control buttons Normal Operation To raise or lower the lectern press and hold the up or down arrow keys on the control pad until the worksurface reaches the desired height The worksurface can be adjusted Figure 2A from 32 5 H minimum to 40 H maximum Up Down Note The lectern has a load sensing anti collision feature A CAUTION A programmed into the controller that actively locks out the l lift mechanisms when unbalanced loads are encountered Keep clear of pinch points during worksur i e an obstruction under the worksurface or weight from a face movement Note The lift actuators person sitting on one side of the lectern provide 540 Ib of lift Always unplug the lectern before working under the worksurface Do not place anything under the worksurface when operating lift Alt
22. skirt Left side skirt SPECTRUM w f INDUSTRIES INC 0118857 Page 5 of 18 Rack Cabinet optional Zp The removable rack cabinet 14RU front 10RU rear simplifies installation and provides the ability to integrate equipment remotely and docked into the lectern at a later date Figure 4A Detaching Cabinet 1 To detach the rack cabinet from the lectern unlock the cabinet lock pawl near the floor Figure 4B 2 Slide the cabinet toward the center of the lectern to release the cabinet from the keyhole slots Docking Cabinet 1 To secure the rack cabinet to the lectern position the cabinet on the left or right side of the lectern 2 Engage the keyhole slots and slide the cabinet toward the outside leg of the lectern to secure 3 Lock the cabinet lock pawl near the floor lg Nis Keyed lock one on each side shown on right side of lectern Quick release lever Keyed lock one on each side Bottom of Rack cabinet Quick release Quick Release Door The symmetrical door can easily be removed or switched to be hinged from left or right using the quick release hinge lever located on the door Figure 4C SPEC ERAM INDUSTRIES ING 0118857 Page 6 of 18 Flip up shelf operation optional Phillips screwdriver Required Operation The shelf will automatically lock into place when lifted into the horizontal position with the levers released Figure 6A To lower
23. y with these instructions may result in accidents involving serious personal injury Failing to follow these instructions can result in the product being damaged or being destroyed A Safety Information General Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed Failure to comply with instructions marked with the NOTE symbol may result in serious damage to the system or one of its components e tis important for everyone who is to connect install or use the systems to have the necessary information and access to the Owners Manual Follow the instructions for mounting risk of injury if these instructions are not followed The appliance is not intended for use by young children or infirm persons without supervision lf there is visible damage on the product it must not be installed e Note that during construction of applications in which the actuator is to be fitted there must be no possibility of personal injury for example the squeezing of fingers or arms ua Assure free space for movement of application in both directions to avoid blockade Before installation re installation or troubleshooting e Stop the DL5 DL6 e Pull out the mains plug e Relieve the DL5 DL6 of any loads which may be released during the work Before start up e Make sure that the system has been installed as instructed in this User Manual e Mak
Download Pdf Manuals
Related Search