Home

TELE-Network

1. In the menu item show messages you can view the current state of the messages The state of every projected message is shown there Even those which can not create messages Thereby a state of the machine can be watched without a PLC programming software The message window is refreshed every 3 seconds When a field is marked red it means that the limit has been exceeded Show Messages PIISUN UPS power supply incoming airtemperature 134 2003 2011 by PI TIS Operating instructions Tele Network 8 12 Communication with TELE SWITCH 8 12 1 Function of the TELE SWITCH as MUX compatible with Siemens MUX 757 All DIP switches are turned to the following adjustment corresponding to the slave number DIP 1 DIP2 meaning OFF OFF channel 1 to 8 corresponding to slave 1 to 8 ON OFF channel 1 to 8 corresponding to slave 9 to 16 OFF ON channel 1 to 8 corresponding to slave 17 to 24 ON ON channel 1 to 8 corresponding to slave 25 to 30 The remaining DIP switches are all turned OFF For the calling the usual PG BUS calling is used 8 12 2 Function as TELE SWITCH DIP 3 has to be turned ON DIP 1 and DIP 2 according to the above table The TELE Network device supports with this operation mode only the slave numbers 1 to 16 The TELE SWITCH can be operated at the PLC or PG socket of a TELE Network device that is configured as PLC TELE In the PG TELE the following adjustments have to be made for c
2. 2003 2011 by PI TIS 19 Operating instructions Tele Network Device name 8 max 9 char router mode 8 Yes No MPI OnBoard 8 MPI OnBoard Y N Yes No MPI OnBoard Baud 6 9 6 kBit s 19 2 kBit s 45 45 kBit s 93 75 kBit s 187 5 kBit s 500 kBit s 750 kBit s 1 5 MBit s 3 Mbit s 6 Mbit s 12 Mbit s OnBoard MPI Adr e 0 126 MPI OnBoard HSA a 15 31 63 126 Fix OnBoard Baud 8 E Yes E No MPI Profibus w E MPI Bus Profi DP Std Profi DP FMS PC MPI Cable 8 E MPI Cable Baud 19200 38400 57600 115200 Cable MPI Adr 6 0 31 Cable HSA 8 S7 Config ONLY for PLC TELE amp SPS MPl Address is only valid if there is no Poll list active for Pager Fax and SPS TELE Poll list if there any entries exist the S7 MPI Adress is not valid Firewall a On Off 20 2003 2011 by PI TIS Operating instructions Tele Network _ PG MUX Mode ONLY for PLC S5 TELE PG MUX PG AG PG MUX c IP Addresses Ethernet IP XXX XXX XXX XXX with Eth Netmask Yes No Ethernet Netmask XXX XXX XXX XXX ISDN IP Address XXX XXX XXX XXX Analog IP Addr XXX XXX XXX XXX Net Config Hostname Input for a logic hostname up to 16 char possible ist DNS XXX XXX XXX XXX 2nd DNS XXX XXX XXX XXX 3rd DNS XXX XXX XXX XXX Std Gateway XXX XXX XXX XXX Or logic name list of hosts Modem Extension Yes No Outline code 0 1 2 3 4 5 6 7 8 9 1 gt H X W Count of Rings 0 1 2 3 4 5 Win2000 TAPI Yes
3. Dialling method recognised correctly Parameters for dialling set correctly Is the phone installation released for data operation Is the modem connected to an ANALOGUE connector Are the parameter values for the return call set according to the instructions PLC TELE and PG TELE correctly configured Uses your company a Call By Call Provider So it is possible that the line is be multiplexed and so the carrier ton is be interrupted Baudrate correctly configured For some countries it is better not to dial with the maximum baudrate it is better to select a baudrate less than 1 or 2 steps Count of rings correctly configured A and B line correctly connected Telefon lead coreectly connected TELE Network device is earthed correctly Cable connection between AG TELE and plc OK Is the device really an AG TELE PG MUX Mode correctly configured Cable connection between AG TELE and plc OK Is the device really an AG TELE Cable between plc and tele correct or damaged 2003 2011 by PI TIS Operating instructions Tele Network License informations The in the Tele Prof Il used software technologies and programmes of the firmware are tied in part to the below listed licenses The parts of source code of the firmware of Tele Prof Il which is tied to the listet licenses can be obtained on request from PI TIS or on your supplier 1 GNU GENERAL PUBLIC LICENSE Version 2 June 1991 Copyright C 1989 1991 F
4. This PCMCIA connector can be used for future communication for e g a memory card for extension of the memory or a flash card for firmware upgrades PE ov i 20 DC 15 VA 2003 2011 by PI TIS 149 9 4 7 PG Connection If the device is defined as PG TELE the connection or programming cable which is normally designed for the Siemens control is now either plugged in the 15pin D SUB socket or 9pin D SUB socket right next to it is connected to the serial interface of the PC with a 9pin 1to1 cable The 9pin and 15pin D SUB sockets right next to it are not used in this setting 150 2003 2011 by PI TIS Operating instructions Tele Network 9 4 7 1 Pin assignment for the PG socket TTY PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 PIN 9 PIN 10 PIN 11 PIN 12 PIN 13 PIN 14 PIN 15 Mext TTY IN 5V 24V ground TTY OUT ground 24V 20mA for sender ground 20mA for receiver 5V ground 9 4 7 2 PIN assignment for the PG socket V24 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 PIN 9 DCD TxD data carrier detect transmit data RxD receive data DSR data set ready GND ground DTR data terminal ready CTS clear to send RTS request to send RI ring indicator 2003 2011 by PI TIS 151 9 4 8 PLC Connection If the device is defined as AG TELE either the optionally available connection cable interface cable V24
5. 13dez e TELE Network device saves maximally 3200 signs from the ASCll subscriber in the cache also several lines e One line can be maximally 510 bytes long including CR A communication flag word as well as a communication data module have to be arranged here compare to PLC TELE The source area is the area that is sent to the AS The AS on the other hand sends to the target area It has to be noted that the target area marks the number of the received bytes in the first word note bytes The TELE LINK does not write the number of the received bytes in the configuration DB but in the 1st word of the target area When sending from the plc to the AS the number of the bytes that are to be send not WORDS as with the PLC TELE is taken over from the configuration DM For the status report the same values as with the PLC TELE are valid If you want to send data from the plc to an ASCll subscriber or if you want to fetch data you have to define a communication flag word a communication data module and the ASCII TELE flag in the TELE LINK The communication flag word and the ASCII TELE flag always have to be an even number 0 2 4 6 254 In order to start the transmission and to call the subscriber 4 the plc now gives the following command to the communication flag word f ex FW 10 0104h The remaining data and the actual communication are executed according to the scheme defined in the DM Please note that you have select
6. 2003 2011 by PI TIS Operating instructions Tele Network 7 4 2 1 3 Setup of the communication data module for S7 for PAGER ii KOPZAWL JFUP SPSTELENSIMATIC 30001 CPU3T3 ADB15 lt Offline gt Datei Bearbeiten Eirfugen Zwispsiem Test Ansicht Eylias Fenster Hile Osla a gt fe fain 4 e m SPSTELENSIMATIC 30011 ACPU3131 1DB15 lt Offline gt rg T 0508 a peo omni ae rogers mn E CS AENA ICC fe AA Po po 20 A AA O TT ETE 29000 rexcende fr Dr cken Sie FI um Hile zu ethaken i Stal Deterc262 Dy DetenO Emigen Z Pay attention that you finish the message text at the end with a 0 The type string is used for the text because is so easier to edit TELE LINK PROF need for the end detection a 00h Please note that you have selected the pg mux mode for pg mux see chapter 6 2 7 PG MUX Mode Only for PLC TELE and S5 7 4 2 1 4 Sending a message to a PAGER After you have correctly defined the PAGER COM DB in the plc now you can give the TELE Network device the commnd for dial For this you write into the communication flag word the 01h for dialing The TELE Network device gives the plc after sending the message the status back The status for sending ok or sending with mistake 2003 2011 by PI TIS 105 7 5 Serial Extension Direct Mode You can select this mode in order to realise a data transmission that does not correspond to a commun
7. TTY is plugged onto the 9pin D SUB socket or the optionally available connection cable is plugged onto the 15pin D SUB socket and is then connected to the programming interface of the Siemens control In contrast to PG TELE a programming system can now be connected either to the unused 15pin D SUB socket or to the unused 9pin D SUB socket This means that the control can be accessed by phone from outside and that the co worker at the face can simultaneously have access to the control with his programming tools 9 4 8 1 PIN assignment for the PLC socket TTY PIN 1 Mext PIN 2 TTY OUT PIN 3 N C PIN 4 N C PIN 5 N C PIN 6 TTY IN PIN 7 ground TTY OUT PIN 8 Mext PIN 9 20mA for receiver TTY OUT PIN 10 N C PIN 11 N C PIN 12 N C PIN 13 N C PIN 14 N C PIN 15 N C Therefore a connection to a TTY compatible interface via a 15pin 1to1 cable is possible 152 2003 2011 by PI TIS Operating instructions Tele Network 9 4 8 2 PIN assignment for the PLC socket V24 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 PIN 9 2003 2011 by PI TIS N C RxD TxD DTR GND DSR RTS CTS N C receive data transmit data data terminal ready ground data set ready request to send clear to send 153 9 4 9 MPI Profibus connector This connector has for the bus pins and ground the same pinning like a plc The TELE PROFessional can be connected
8. the current PLC value see an example with the PLC value 0 2048 correspond 256 to 256 in the display PLC value1 PLC value which corresponds the HMI value1 0 PLC value 2 PLC value which corresponds the HMI value2 oe HMI value 1 HMI value which corresponds the PLC value1 256 25 MIS HMl value 2 HMI value which corresponds the PLC value2 256 Configure messages Access rights Level Write Superuser Read View U2 The actual messages are configured seperately The relation between variable norming and report groups can be defined there whereof the actual message will result from The order of the messages is resolved by input In later versions it can also be changed Ino text variable active Delay sec it mit norming co Gi 62 63 64 65 Gs G7 68 co Za 1 UPS power supply E40 x 10 0 00 On off zi Ga 2 incoming air temperature MW30 x 200 gt 40 00 DegreesC mal x he ik Mal i o oo 130 2003 2011 by PI TIS Operating instructions Tele Network The meaning of each column messages Column Usage Text Own notation Variable Here you can assign a variable to the message If no variable is assigned only the text will be displayed Active If the cross is set the message is active and worked up Without cross the variable will not be worked up Delay The ti
9. 2011 by PI TIS Operating instructions Tele Network 8 Special Functions 8 1 RECALL mode In order to optimise or save phone charges for example for longer and often international calls you can receive recalls from the TELE Network device of your interlocutor After the firm or the technician there has reported a disturbance of the installation you call there with the TELE Network device and cause a return call In this way the phone costs are at the customer s expense Please make the modifications described in the following chapters in order to be able to work with the return call mode 8 1 1 PLC TELE On the PLC TELE you have to config following Count of Rings minimum 1 or bigger Dial Mode Tone or Pulse Extension Yes or No Outline Code 0 1 2 3 4 5 6 7 8 9 gt H X W Recall Mode YES 8 1 2 PG TELE In the PG TELE you have to configure following Count of Rings minimum 1 or bigger Recall Number Own telefon number of this tele network device if you want a Recall from other areas only with precall number In your Edit Subscriber you you have configured the telefon number you want the recall you just have to select the baudrate beginning with the Rxxx So for example the R144 this means you want a recall with 144000 baud As soon as the Baud rate with the R has been activated a new input field will be shown after the input of the phone number RC PNr This return call prefix number s
10. No Analog Analogmodem German Komplex USA 600R System Dial mode Tone Pulse Busy identify Yes No 2003 2011 by PI TIS BE a E EN e E E a O a O E O a O a O a O a O a O a O a O Operating instructions Tele Network Speaker a On Off Hangup hearing e 0 10 Secs Baudrate manual 8 12 24 48 96 33K Analog on ISDN 8 Yes No ISDN aLaw uLaw 8 aLaw EUR Northam uLaw Southamerika ISDN ISDN Protocol a O Euro ISDN 1TR6 ISDN EAZ MSN O 0 999 Extern external modem im Yes No Baud ext modem E 9K6 115K2 ext Modem cmd 8 Yes No UMTS GPRS UMTS Modem a Kind of net 8 only GPRS only UMTS 1 GPRS 2 UMTS 1 UMTS 2 GPRS UMTS PIN a 8 Enter the UMTS Pins max 8 char No SMS Centre O APN m PIN 6 chars Connection Callback mode ONLY for PLC TELE amp Yes No Callback no ONLY for PG TELE Telephone number max 16 char Max Connecttime i 0 up to 60 minutes Max Idletime im O 0 up to 60 minutes 22 2003 2011 by PI TIS Operating instructions Tele Network Access code dialin protect a 8 Yes No PIN device local E 6 chars Pin PIN plc local E 6 chars Pin PIN device remote E 6 chars Pin PIN plc local 6 chars Pin modem users H delete WEB user a O Special i to PG PLC COM ONLY for PG TELE s Connect PG with PG PG socket of the PLC Tele Connect PG with PLC PLC socket of the PLC Tele s
11. Without inputting a password PLC OFFLINE is reported via the telephone line and then there is an access is not possible local gt means the device in front of you Max 6 characters 6 2 13 3 PIN device remote Input of the password PIN device local at the partner device with which you are connected via the telephone line Input only possible if the partner device does not have a password protection or if the user knows the password Remote gt means the device you have access to via the telephone line Max 6 characters 2003 2011 by PI TIS 65 Operating instructions Tele Network 6 2 13 4 PIN plc remote Input of the password PIN plc local at the partner device with which you are connected via the telephone line Input only possible if the partner device does not have a password protection or if the user knows the password Remote gt means the device you have access to via the telephone line Max 6 characters The access to a TELE Network device that is protected by a password via the telephone line see Login Remote or at the device itself is only possible if the user knows the password Please do not forget your password or keep it at a safe place In case you forget the password you have to send the device back to the producer because it has to be reset in its original state This cannot be done by the customer or the partner or by telefone line 66 2003 2011 by PI TIS Operatin
12. fed through mode finished yy Channel 01 to 16 call corresponding slave number After this input the question Switch YES NO is displayed e YES Input is taken over channel is called e NO Input is dismissed present condition remains If there is a call then it is reported whether the call or the transformation respectively were successful or not After connection clear down the SWITCH is automatically deactivated 5 2 2 9 5 IBX Test Only for PLC S5 KOR MUX If you have selected the device type KOR MUX TELE you have now the possibility to test the connected pg bus First you select Test IBX xx xx stands for the pg bus number 1 to 31 The tele tells you if the selected slave is connected Automatic the tele tries to connect the plc and gives you an OK if the Connection is good or gives you the message where the failure is 5 2 2 9 6 Restart Prof Il With this menu item you can reset the TELE PROFessional ll If you have an active telephone call and you should reset the device on the other side you activate the remote configuration and select this item So then the telephone line will be broken but this is for a reset normal With this reset the remote configuration will be also off 5 2 2 10 Language By using the UP DOWN key you can select between German and English menu drive 42 2003 2011 by PI TIS Operating instructions Tele Network 5 2 2 11 Info 5 2 2 11 1 Version This menu item inform
13. mask same in the current network in your system Between these 4 blocks you can change with gt and lt The input will be finished with the ENTER key The TELE PROFessional Il uses the subnet mask 255 255 255 0 6 2 8 4 ISDN IP Address The communication between each device is a ppp protocoll so every device need a different ip address As you can connect with ISDN or analogue so you need 2 different ip addresses So every PG TELE needs another address like the PLC TELE While you don t need a communication between PLC TELE and other PLC Tele PLC TELE option the addresses can be the same Please configure this address like 172 16 1 1 This address is also divided in 4 blocks Between these 4 blocks you can change with gt and lt The input will be finished with the ENTER key Please change only these IP address for your PG TELE because all other delivered devices has the same address So you don t have to make any thought about this menu item 58 2003 2011 by PI TIS Operating instructions Tele Network 6 2 8 5 Analog IP Address The communication between each device is a ppp protocoll so every device need a different ip address As you can connect with ISDN or analogue so you need 2 different ip addresses So every PG TELE needs another address like the PLC TELE While you don t need a communication between PLC TELE and other PLC Tele PLC TELE option the addresses can be the same Please configu
14. 01h The command to send is triggered The entries in the communication DM are treated as a command to send The defined sector is transmitted to the partner Sender sender of the command source receiver partner target 02h The command to fetch is triggered The entries in the communication DM are treated as a command to fetch The defined sector is transmitted from the partner to the sender of the command Sender sender of the command Target receiver partner source Transmission status 01h command ready without mistakes 02h command executed but you have to check for TIMEOUT the command should be completely executed after 45 seconds 03h source module does not exist or is too short 04h target module does not exist or is too short 05h mistake the command has to be repeated 06h configuration DB does not exist 07h parameter fault 08h the partner device is not a SPS TELE 90 2003 2011 by PI TIS Operating instructions Tele Network 7 2 1 3 Setup of the communication data module at the SPS TELE 7 2 1 3 1 S5 DWO KC data type of the source at the moment only DB possible DB data module EB entry byte DW1 KF source DB number DW2 KF initial address of the source sector StartDWNr DW3 KF number of words DW4 KC Data type of the target at the moment only DB possible DB data module EB entry byte DW5 KF target DB number DW6 KF initial address of the ta
15. 2 2 5 6 Login Remote With this action you can repeat the password input a second time after you had logged in incorrectly 28 2003 2011 by PI TIS Operating instructions Tele Network 5 2 2 5 7 Transmit programme This command is used to transmit newer software versions to TELE Network devices with older versions Your own programme is loaded to the other TELE Network device via the telephone line to the programme memory In this way all TELE Network devices can be updated with the most recent software release Programmes can only be transmitted between device types that are configured differently PLC TELE PG TELE or PG TELE PLC TELE If the devics are of the same type PLC TELE PLC TELE or PG TELE PG TELE there will be the error report partner does not recognise option The TELE Network device that has received the programme programmes itself after the transmission While the programming is in process do not disconnect the device from the voltage supply since then the complete programme becomes invalid If the programme is invalid the device reports an ERROR If this message appears the device has to send to your local distributor After the programming the device executes a warm Start and after that it reports with the new software release yet with the same configuration 5 2 2 5 8 Fetch programme This is the contrasting command to the command Transmit programme More recent software releases are
16. 35 Operating instructions Tele Network 5 2 2 6 15 Menu item Dialmode e Tone The modem dials with the modern MFV system That means you hear while dialing a little melody e Pulse The modem dials with pulses That means you hear while dialing the noise of a relais 5 2 2 6 16 Menu item Extension mode e YES The device is not connected directly to the line You then need either a prefix number or a certain key combination to get to the line e NO The device is either connected directly to the line i e you do not need a prefix number in order to get a line or the device is within a private branch exchange and should call a partner within this system 5 2 2 6 17 Menuitem Outline Code With these possible figures you can config the device to get a telefon line 0 1 2 3 4 5 6 7 8 9 1 gt H X W 5 2 2 6 18 Menuitem Rings before Lifting e 0 With this adjustment the modem does not pick up independently With the menu item pick up you have to make the modem pick up manually e 1 5 Modem picks up after the adjusted number of rings The operation of these remote maintenance units is only allowed if a supervising person is present who can intervene in the installation at any time Please do not intervene in running programmes without visual communication or control Before installing the TELE LINK Network devices please connect them by all means with earthing PE at the casing or at the screw terminal Please read the
17. Break Tx line ONLY for PG TELE amp 0 bis 30s S7 200 on ONLY for PG TELE s Direct mode ONLY for PG TELE amp Source COM Dest COM DM on DM on with Handshake Tele Switch ONLY for PG TELE amp PRO TOOL 7 17 ONLY for PG TELE amp IBX TEST ONLY for PLC TELE s Reboot Profll 3 Soft Restart Es Language 0 E German English Info e Version OS Version Remoteversion Remotename Serial number MAC Address Copyright 2003 2011 by PI TIS 23 Operating instructions Tele Network Options Pager TELE Pager Mode Yes No Pager Flag Only even flag words 0 to 254 Pager COM DB DB1 to DB 255 DW 0 to 998 PLC ASCII TELE Modem control No With flag word Modem Flag Only even flag words 0 to 254 PLC TELE Mode Yes No PLC TELE Flag Only even flag words 0 to 254 PLC TELE KOM DB DB1 to DB 255 DW 0 to 998 ASCIl Mode Yes No ASCII Flag Only even flag words 0 to 254 ASCII COM DB DB1 to DB 255 DW 0 to 998 FAX TELE Fax Mode Yes No FAX Flag Only even flag words 0 to 254 FAX COM DB DB1 to DB 255 DW 0 to 998 Resolution Fine Heavy FAX POLL DB DB1 to DB 255 DW 0 to 998 a amp 2003 2011 by PI TIS Operating instructions Tele Network 5 2 2 1 Menu item messages In this menu item which occurs automatically on the display after starting the TELE Network device the user receives important data about the condition of his her device It is displayed whether the TELE Network has a di
18. E A EA seneeetessae 67 7 1 1 4 Communication establiSNMent ccccecceceeeeeeeeeee cae ceeeeeceeeaaeceeeeeeescaaeaeeeeesesencaeaeeeeseesecaeaeeeeeees 68 AAAS ACCESSING PLC econ ade 69 7 1 2 WinTeleProf as replacement for PG TELE ccccccccccesseeeeeeeeeeeeeeeeeees 70 01 2 1 What is WinTeleProf ivi A sesh hued ia 70 L 1 2 2 REQUIFEMENIS ai Reeth thee Sets Oe Gaede aaa nei ates a oa teed aa ieee 70 KA 2 Instala cc ltda datado taea 70 7 1 2 4 Communication establiSNMent ccceecccceeeeeeeeeee cae ceeeeecesenaaeaeeeeeceeneaeaeeeeeseseeaeaeeeeeenseeaeaeeeeeees 72 7 1 3 Operation with UMTS GPRS Internet OPenVPN c oooooncccccocccccccccnoroonncnocnnnos 75 LAIA Requerida veer Mocatekel teredhal deen eiaplantanceakeusMashaeet tebe 75 13 2 SUpPOMed AAA O O EEATT 75 LAI Installationen A A adn 76 7 1 4 Tele Prof Il and GSM as Telephone line o ccccccccccccceeeeeeeeeeeeeeeeeeeeeeeeeenees 86 fee PEC COUPUING dt AR E A A AAA AS AA A ERA ARAS 89 7 2 1 Coupling of several pics via the telephone liN ooooooccoccccnccccococannccccnoncnnns 89 7 2 1 1 Set up a communication word between the plc and the TELE Network device i e 89 2 1 2 Setup of the SPS TELE flag ci tao 90 7 2 1 3 Setup of the communication data module at the SPS TELE 0 0 eee ee eeeeeeeeeneeeeeeeeeeeenaeeeeeeaeees 91 7 2 1 4 Send data with the SPS TELE oooncccnnccinccoconcconoccconcnnnoncnonnnnno ccoo nn nan c cnn n nn nr nn nn n nr nr nn rana n rr arn
19. Start connection If this configuration works you can configure via internet 2003 2011 by PI TIS 85 7 1 4 Tele Prof ll and GSM as Telephone line The Tele Prof Il also can be called via GSM any time Therefore you have to notice the following points e PSI GSM GPRS Modem RS232 by Phoenix SIMM Card 3 3V with activated CSD Circuit Switched Data service It is not an M2M connection and will not be billed by volume Mega Byte Normally it is a regular SIM Card with an extra phone number for modem communication and one for FAX communication The GSM Modem has following parameters Thereto Phoenix supplies an extra parameter software called PSI MODEM CONF The parameters for the serial interface should be set like following Serielle Schnittstelle COM Port M COM1 Tf COM2 f COM3 COM4 COM5 f COM6 JS COM COM8 Baudrate Datenbits Y v 8 Paritat Stopbits 1 x Abbrechen Other serial parameters concerning the baud rate are possible any time but the best experiences have been found with 57K6 The Baudrate 115200 has sometimes not been recognized correctly by the modem 86 2003 2011 by PI TIS Operating instructions Tele Network The modem settings itself GSM GPRS Konfiguration Profil Einstellungen gt Telefonbuch Echo v Speicherplatz 1 DCD Signal y Jan wenn Trager erkannt Speicherplatz 2 DSA Signal v immer AN Speicherplatz 3 DTR Signal y 150 Auflegen Speicherplatz 4 Flusskon
20. TELE option the addresses can be the same Please configure this address like 172 16 1 1 This address is also divided in 4 blocks Between these 4 blocks you can change with gt and lt The input will be finished with the ENTER key Please change only this IP address for your PG TELE because all other delivered devices has the same address So you don t have to make any thought about this menu item Menuitem Analog IP Adr The communication between each device is a ppp protocoll so every device need a different ip address As you can connect with ISDN or analogue so you need 2 different ip addresses So every PG TELE needs another address like the PLC TELE While you don t need a communication between PLC TELE and other PLC Tele PLC TELE option the addresses can be the same Please configure this address like 172 16 1 2 This address is also divided in 4 blocks Between these 4 blocks you can change with gt and lt The input will be finished with the ENTER key Please change only this IP address for your PG TELE because all other delivered devices has the same address So you don t have to make any thought about this menu item Menuitem analogue modem e German complex The connected telephone system is complexed e USA 600R The connected telephone system is 600R With this selection you should work in the USA and the other world but not in Europe If the modem picks up but the modem noise is not hearabl
21. Utilities C Media 3D Audio EasyCODE Eltima Software Ethereal FreePDF L peA Y Click Next to continue with the installation Back to review the last step or Cancel to exit ThunderSetup lt Back Cancel 15 User information Please type your name and the name of the company you work 5 for In the following dialog choose the Installationstype and click Next to Name Werner Sonnertag continue Now type your name and Company Pocessiniomatk the name of your company and confirm by clicking Next ga Sen to rns with the installation Back to review the last 6 N OW a S h O rt S u m m a ry i n wh i ch yo u step or Cancel to exit A A can review your entries Cancel ThunderSetup 2003 2011 by PI TIS 71 7 Now the software will be installed to your PC This may take a few minutes on elder systems 16 Installation complete Setup has finished the installation of Win TELE PROF In order to 8 To com plete the in sta llation make the program work properly you will need to restart Windows you mu st reboot you r PC E now Therefore let the checkbox Reboot now checked and click Finish Reboot now Click Finish to complete setup ThunderSetup 7 1 2 4 Communication establishment 1 When starting the software for the first time a the Settings dialog will appear Here you can Ind define the virtual COM Ports This dialog can Pesremmevriwinr
22. WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF AD VISED OF THE POSSIBILITY OF SUCH DAMAGE This product includes cryptographic software written by Eric Young eay cryptsoft com This product includes software written by Tim Hudson tjh cryptsoft com BusyBox BusyBox is licensed under the GNU General Public License version 2 BusyBox is licensed under the GNU General Public License version 2 which is often abbreviated as GPLv2 This is the same license the Linux kernel is under so you may be somewhat familiar with it by now A complete copy of the license text is included in the file LICENSE in the BusyBox source code Anyone thinking of shipping BusyBox as part of a product should be familiar with the licensing terms under which they are allowed to use and distribute BusyBox Read the full test of the GPL either through the above link or in the file LICENSE in the busybox tarball and also read the Frequently Asked Questions about
23. YENER 53 6 2 4 1 MPI OnBoard Nas 53 6242 MPI OnBoard Baud a iii 53 6 2 4 3 OnBoard MPI A dF nana 53 6 2 4 4 MPI OnBoard HSAs sit crested tad el as dear er Scania a cad hs Vane ea at Bes 54 6 2 4 5 Fix OnBoard Baud nana 54 6 2 4 6 MPI ProfibUs ama 54 0 20 PO MPIECADIS ear E A RG AS 55 6 2 5 1 MPI cable Baud am 55 6 2 5 2 MPI cable Adr cccccececccsecesescececcecececcsceceesececsececusvevacsesecacssseaceeesacsaavaceesacacavstasestcestatestetsteneetere 55 2 2003 2011 by PI TIS Operating instructions Tele Network 6 2 0 3 Cable HSA cast dto aa cronos 55 6 2 6 S7 Config ONLY for PLC TELE ss 56 6 2 0 FPLC MP addres Siriei siin aaa tires ehacearaceushohaeneshatestestehelt et ea a earen aAa aA Neen 56 6 2 6 2 E EAA AT E A E EA A TAE LIO E 56 6 2 7 PG MUX Mode Only for PLC TELE and S5 seeeeeeeeeeeeeesssseeeeeeeees 57 OLA ADOOS SP 57 6 29 11 EthernetlP soviet tee iyi eles ack let ie so Mies hes ah one et a ol oe Meet a es oH oes 57 622 8 2 mit Eth Netmask csper poda oes daoedeys A ia 58 6 2 8 3 EtherneteNetMaSkK 0scusiiicata nina tai ltda 58 6 2 8 4 1SDN IP Address tit ca arta titi 58 6 2 8 5 Analog IP Adres icon A e A AA aan 59 e A O O tive oa eteranash a t Eat 59 6 2 9 1 EXtenSion A ea eerie rete ein eee die dele erin ae 59 6 2 9 2 Outline Code iis cecccecacedesece scien ceeds sseetuesicac dese de eeceegueesendsveecaedseeveevenedetvcedees eetuedslereenvsatedeteeeeesseeecunderet 59 6 2 9 3 Count of RINGS aerae
24. are connected to the H1 Bus With the menu item Special items and the submenu item To the PG PLC interface it is decided at the PG TELE whether the communication at the PLC TELE is via the PLC socket or the PG socket Possible adjustments e Connect PG socket with PLC socket normal setting e Connect PG socket with PG socket 2nd ple or switch to CP connection 8 4 Operation of several plcs via the L1 Bus It is no problem to attend a complete L1 network With an additional software option it is possible to configure the PLC TELE in sucha way that a local PLC can be connected at the PLC socket of the PLC TELE and that a CP can be connected at the PG socket After the connection set up the programmer decides at the PG TELE whether he she wants to programme at the PLC or at the CP With the Bus calling of his her S5 software he she can reach and programme all the SIMATIC S5 PLCs that are connected to the L1 Bus With the menu item Special items and the submenu item To the PG PLC interface it is decided at the PG TELE whether the communication at the PLC TELE is via the PLC socket or the PG socket Possible adjustments e Connect PG socket with PLC socket normal setting e Connect PG socket with PG socket 2nd plc or switch to CP connection 2003 2011 by PI TIS 113 8 5 Operation of several pics via the L2 Bus It is no problem to attend a complete L2 network With an additional software option i
25. assignment for the PG socket V24 ooo eeeeeeeeceeeeeeeeeneeeeeeeaeeeseaeeeeeeaaeeeseeeaeeesnneeeensnaeeeeenees 151 O46 A A A EIN 152 9 4 8 1 PIN assignment for the PLC socket TTY ioonncccnnociconococcnononcnnnonononnnonnccnnno nn nrnnnn cnn nn rra 152 9 4 8 2 PIN assignment for the PLC socket V24 coccocccococococococcnccoconononoconcnnnnnanonncnncnnnnnn nn nr cnn nn nnnnnnnnnns 153 9 4 9 PPI MPI ProfiDUS CONNECHOD ooccoocccnccccccncocccnoccnocnononononononnonanononnnonnonananonos 154 9 4 9 1 PIN assignment for the MPI PPI ProfibUS POTt ooooonooccccnnociconoconococcnccnnnnononnncncnnnnno no nn nnncnnannn nn cnc 154 HATO Vollade COMnNCCHON rosa 155 Oi PECAN PES Ad denia 156 A OA A fie Ak ot dt ted Ne 157 10 TROUBLESHOOTING wrsccsaiccsccessccacctaecideeais etic acces aed 158 2003 2011 by PI TIS 5 Operating instructions Tele Network 1 Preface The TELE Network devices were developed especially for the remote maintenance of plc systems This means that the device is geared completely to industrial necessity from its mechanical configuration to its handling The compatibility of the TELE Network devices with the original programming tools of the respective plc manufacturer has highest priority Their connection mechanics pin seizure and electrical data meet the specifications of the respective controls Thus users can work directly and without special adapters with the normal cables of the devices they want to connect like for
26. be a fix or a DynDNS registered address If you use our OpenVPN Install Tool the file TProf2config ovpn will be installed in program files OpenVPN Config Enter the following parameters in this file for remote P Address of dest device e g fix xxx yyy nnn xxx or a DynDNS registered Domain e g test dyndns org port like configured in TELE PROF II Default 1194 Note that your firewall has to allow the UDP Connection for this Port 82 2003 2011 by PI TIS Operating instructions Tele Network Statement from the Config file HHFHHHFFHHASHHE ASHE ASHH RRA E SSH HERR RRR HH aH HH client side OpenVPN 2 0 config file for connecting to TeleProf He E HE HE On Windows you might want to a ene this file so it has a ovpn extensio TT hier die Remote IP Adresse f r TELE PROF 1 eingeben here set the remote ip address of TELE PROF e g remote tprof2 dynalias org replace xxxx with the i p address remote tprof2 dynalias com hier den Port fur OPenVPN eingeben here set port of TELE PROF 1l standard is 1194 if you change it you have to change it on both sides port 1194 You can create this file for every of your machines and rename the file after the name of the corresponding machine 2003 2011 by PI TIS 83 7 1 3 3 4 Connection establishment by using the OpenVPN GUI After installation the OVPN GUI Symbol eJ should appear in the task list Move the cursor over the ic
27. can find under http www openvpn net Here the function of OpenVPN is described how it is implemented in TELE PROF II Basically there are two operating modes of OpenVPN server or client Normally the device on machine side PLC TELE is configured as server With OpenVPN we provide a new network interface in TELE PROF II This interface will quasi be connected to the OpenVPN interface of the partner device with a virtual line This line will be realized with software Thereby all protocols for this interface are exchanged via an own UDP Channel You can say it is a phone call per UDP between both devices Obviously the connection is crypted The keys are stored in TELE PROF II 7 1 3 3 3 2 OpenVPN server mode Enclosed the sample settings TELE PROF Il PIISDNST v arver 10 111 111 0 iver 255 255 255 0 In server mode you give the IP Address which the network interface of the OpenVPN server will obtain This will be committed in IP pool In our sample the Server will get the Address 10 111 111 1 and 10 111 111 2 OpenVPN will reserve these addresses automatically because later a PPP Connection will be realized across them In IP pool netmask you can define from which IP Range the clients which connect to your TeleProf via OpenVPN will get an IP Address for their networt interface When choosing the addresses note that you select an address range which is not used by the Ethernet Interface of the Prof Il or by
28. delivered devices has the same address So you don t have to make any thought about this menu item 5 2 2 6 13 Menu item Analog IP Adr The communication between each device is a ppp protocoll so every device needs a different ip address As you can connect with ISDN or analogue so you need 2 different ip addresses So every PG TELE needs another address like the PLC TELE While you don t need a communication between PLC TELE and other PLC Tele PLC TELE option the addresses can be the same Please configure this address like 172 16 1 2 This address is also divided in 4 blocks Between these 4 blocks you can change with and lt The input will be finished with the ENTER key Diese IP Adresse wird in 4 Blocke aufgeteilt Bitte geben Sie diese Adresse zum Beispiel 176 16 1 1 ein Zwischen den Bl cken k nnen Sie mit gt und lt wechseln Die Eingabe wird mit der Enter Taste angeschlossen Please change only this IP address for your PG TELE because all other delivered devices have the same address So you don t have to make any thought about this menu item 5 2 2 6 14 Menuitem analogue modem e German complex The connected telephone system is complexed e USA 600R The connected telephone system is 600R With this selection you should work in the USA and the other world but not in Europe If the modem picks up but the modem noise is not hearable then you should change the modem type 2003 2011 by PI TIS
29. e are a ea oca on 60 6 2 9 4 Analog Mode Misiin ae iea e a e ie iad 60 622925 Dial MOG AEE EEA E E AE T E E ETAN 60 6 2 9 6 Extension w 0e cacti an Aree eet nee annie ania asad ETN 61 6 29 Oper PAS 61 6 2 9 8 HangupiheariQlsiratistoaorl lala 61 6 2 9 9 Baud rate Malal tati tea eal eri ant Dia de 61 6 2 9 1041SDN Protocol 0 cave cececeesNas ductor etsdncsbancectae use A A I E E 62 6 2 9 1 ISDN EAZ MSN nn cece diese ates A AE ia 62 0 29 12 Analogue on ISDN iregi oni r e sctevbevcand cnvespoe odes sede a ara daea 62 6 2 9 13 ISDN alaWuLIWistinnacion aran paladio naai dea aida t 63 PAR A A O Ri adaansted adi dace evita dace 63 6 2 9 15 Ext Modem Daud cc cs cc econ ceeceddecdensnededee A cess dieas 63 LIO CON SCUO Ntro 64 6 2 11 Recallmode Only Tor PLO TELE aint idicta bil tos 64 6 2 12 Recallnumber Only for PG TELE ooooccocccccccccccccnnccnccccnnonononcnnnnnnnnnnininos 64 6 2 12 1 Max Connect time cocino oe 64 6212 2 Max dE MA necnts eee agus ees abebucstotaegesady titan netiac R aii 65 02 19 ACCESS COMO id A RO 65 6 2 13 1 PIN device local cooooininicii a EA 65 6 2 13 2 PIN pe local ic alo o alii 65 6 2 13 3 PIN device remote ira dalt 65 6 2 18 4 PIN PIC ROMO te E EAEE EE ant 66 7 FIELD OF APPLICAT ION A instances 67 7 1 REMOTE MAINTENANCE ASA RIOS 67 7 1 1 Via telephone MI aio 67 111 1 Description EE ged hate es See E EEE E E E E E 67 C1322 Regue eN S cotilla di ates oats Cote cas 67 TAE Greate SUDSCIIDS E E E E E
30. flag In case you selected with FW with flag word in the menu item modem control you can now enter the common flag word for the modem control Use even numbers only e g FW 120 Only 0 to 254 5 2 2 8 2 3 SPS TELE operation With this menu item you can turn the PLC TELE operation on or off 5 2 2 8 2 4 SPS TELE flag With this menu item you can input the common flag word for the data communication Use even numbers only e g FW 122 Only 0 to 254 38 2003 2011 by PI TIS Operating instructions Tele Network 2 2 8 2 5 SPS TELE COM DB With this menu item you can set the communication data base DB in order to set parameter values to the data flow source and target at the PLC TELE operation DB1 to 255 DW 0 to 998 5 2 2 8 2 6 ASCII operation With this menu item you can turn the ASCII TELE operation on or off 5 2 2 8 2 7 ASCII flag With this menu item you can set the common flag word for the data communication Use even numbers only e g FW 122 Only 0 to 254 5 2 2 8 2 8 ASCIIl COM DB With this menu item you can set the communication data base DB in order to set parameter values to the data flow source and target at the ASCII TELE operation DB1 to 255 DW 0 to 998 O 2003 2011 by Pl TIS 39 Operating instructions Tele Network 5 2 2 8 3 FAX TELE This menu item is only activated if the TELE Network device has a FAX option 5 2 2 8 3 1 FAX TELE o
31. for e g from WinCC will be send to this defined plc whether which rack or slot number you have configured Would you communicate to many different plcs on this mpi bus you have to switch use default dest mpi address to no So you will be able to communicate up to 20 to the mpi profibus connected plcs per TCP IP for e g with WinCC The access will be realised with the ethernet ip address or a dial up connection and the rack respective slot number For the data exchange between the S7 plc and pc above TCP IP with CP343 1 or CP443 1 the user has to make the same definition for e g for WinCC or other applications with ip address of the CP and rack and slot number The Tele Prof Il is connected to the mpi or profibus and is so not able to communicate with rack or slot number There fore for this is in the Tele Prof ll a S7 CP MPI assignment table implemented So with this table is a plc reachable with her mpi address So you refer to a particular rack or slot number the mpi address For example If in your mpibus are 4 plcs with the addresses 2 3 4 and 5 and you will communicate with WinCC above TCP IP to this plcs you have to configure following S7 CP MPI assignment TELE PROF Il no name MPI addr Rack Slot active 1 S7 PLC MPE2 2 0 2 x 2 S7 PLC MPE3 3 0 3 x 3 S7 PLC MP4 4 0 4 x 4 5 0 5 x 5 0 0 0 S7 PLC MPE5 xix X XX PPP PP So you have to configure in WinCC the addresses for e g plc with mpi
32. from distribution of the Library 166 2003 2011 by PI TIS Operating instructions Tele Network If any portion of this section is held invalid or unenforceable under any particular circumstance the bal ance of the section is intended to apply and the section as a whole is intended to apply in other circum stances It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system it is up to the author donor to decide if he or she is willing to distrib ute software through any other system and a licensee cannot impose that choice This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License 12 If the distribution and or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries so that distribution is permitted only in or among countries not thus excluded In such case this License incorporates the li
33. have connected the device to the telephone line but not given a password for the authentication VPN user TELE PROF Il PIxISDNST active PhdSDNST jp user password password repeat foro Telemeister Ottol HE Eee z ATTENTION Only users which are marked with active will be allowed to connect If no users are entered or no user is active so every user will be allowed to connect never mind which username or password is used So the access is opened THEREFORE minimum one active user should exist This option is only helpful if you have lost your login data and it is necessary that you have to access the machine 80 2003 2011 by PI TIS Operating instructions Tele Network The server side PLC Tele is now configured We presuppose that the PLC Tele is connected to the internet eg via UMTS and reacheable under teleprof dynalias org 7 1 3 3 3 4 Client PG Side Create an entry under VPN connections which points to the address teleprof dynalias org Protocol UDP Port 1194 Users have to be created under VPN User Same as PLC TELE TELE PROF It PbdSDNST user name server adar only client protocol 1 192 168 0 14 192 168 0 14 UDP 1194 2 teleprof dyndns org teleprof dyndns org UDP 1194 Otto Telemeis al UDP 0 Now make sure that the PG Tele has an internet connection This c
34. loaded down from the TELE Network devices Here the programme of another TELE Network device is loaded to your own programme memory via the telephone line In this way all TELE Network devices are updated to the most recent software release Programmes can only be transmitted between device types that are configured differently PLC TELE PG TELE or PG TELE PLC TELE If the devics are of the same type PLC TELE PLC TELE or PG TELE PG TELE there will be the error report partner does not recognise option The TELE Network device that has received the programme programmes itself after the transmission While the programming is in process do not disconnect the device from the voltage supply since then the complete programme becomes invalid If the programme is invalid the device reports an ERROR If this message appears the device has to send to your local distributor After the programming the device executes a warm Start and after that it reports with the new software release yet with the same configuration 2003 2011 by PI TIS 29 Operating instructions Tele Network 5 2 2 5 9 Send OS This command is used to transmit newer OS versions to TELE PROFessional ll devices with older versions Your own OS is loaded to the other device via the telephone line to the programme memory In this way all TELE PROFessional ll devices can be updated with the most recent software release Programmes can only be transmit
35. mkswap c which stated they may be 2003 2011 by PI TIS 169 redistributed as per the Linux copyright which Linus clarified in the 2 4 0 pre8 release announcement in 2000 was GPLv2 only and Linux kernel code copied into libbb loop c after Linus s announcement There are probably more because all we used to check was that the code was GPL not which version Before the GPLv3 draft proceedings in 2006 it was a purely theoretical issue that didn t come up much To summarize every version of BusyBox may be distributed under the terms of GPL version 2 New versions after 1 2 2 may only be distributed under GPLv2 not under other versions of the GPL Older versions of BusyBox might or might not be distributable under other versions of the GPL If you want to use a GPL version other than 2 you should start with one of the old versions such as release 1 2 2 or SVN 16112 and do your own homework to identify and remove any code that can t be licensed under the GPL version you want to use New development is all GPLv2 License enforcement BusyBox s copyrights are enforced by the Software Freedom Law Center you can contact them at gpl busybox net which accepts primary responsibility for enforcement of US copyrights on the software and coordinates international copyright enforcement efforts for such works as necessary If you distribute BusyBox in a way that doesn t comply with the terms of the license BusyBox is distributed un
36. modify sublicense or distribute the Program except as expressly provided under this License Any attempt otherwise to copy modify sublicense or distribute the Program is void and will automatically terminate your rights under this License However parties who have received copies or rights from you under this License will not have their licenses terminated so long as such parties remain in full compliance 5 You are not required to accept this License since you have not signed it However nothing else grants you permission to modify or distribute the Program or its derivative works These actions are pro hibited by law if you do not accept this License Therefore by modifying or distributing the Program or any work based on the Program you indicate your acceptance of this License to do so and all its terms and conditions for copying distributing or modifying the Program or works based on it 6 Each time you redistribute the Program or any work based on the Program the recipient automati cally receives a license from the original licensor to copy distribute or modify the Program subject to these terms and conditions You may not impose any further restrictions on the recipients exercise of the rights granted herein You are not responsible for enforcing compliance by third parties to this License 7 If as a consequence of a court judgment or allegation of patent infringement or for any other reason not limited to patent issues co
37. more you can order a corresponding number of names from DynDNS against payment Roughly it works like following You register your desired hostname at DynDNS e g mysystem dynalias com For your access you will get a username and password These you have to enter in the setting DynDNS config and set use DynDNS to yes At the next internet dial up the TELE PROF II will register the IP Address which is assigned to it under mysystem dynalias com Instantly you have access to the machine via the address mysystem dynalias com However you are working with the firewall see below and the access via modem except for OpenVPN is blocked the ping or something like that won t work For testing you can unblock the ping service via modem Now you should get an answer at ping mysystem dynalias com Deactivate ping via modem again internet connection must not be closed and you will get no answer Now you know that your device is reachable via internet From now on you can create a connection to the device via OpenVPN and maintain your machine Even OpenVPN uses the entry mysystem dynalias com 78 2003 2011 by PI TIS Operating instructions Tele Network What to do if no public IP Address is present Please read the chapter OpenVPN first at the end of the text you will find a solution 7 1 3 3 3 OpenVPN 7 1 3 3 3 1 Function In the TELE PROF II we have implemented the popular under Opensource published OpenVPN Detailed information you
38. network devices e software updates and options transmittable by the telephone line e update and hotline service are for free e integrated Web Browser for configuration the device e possible integrated functions fault report via the fax data transmission to higher ranking plc data transmission to pc server data transmission Scall Quix SMS message standard in Siemens Network devices printer connection L2 BUS interface configuration of control devices e g Siemens OPs PCS OP s standard for the Siemens Network Devices CAN BUS interface Interbus S interface image transmission digital camera sending of e mail e coupling via VPN e coupling via ethernet 10 2003 2011 by PI TIS Operating instructions Tele Network 4 Scope of delivery and accessories 4 1 Scope of delivery The TELE PROFessi Onal Il is delivered without any accessories Additionaly required accessories can be purchased later on For more information please read chapter 4 2 Optional accessories 4 2 Optional accessories 4 2 1 Interfaces switcher Order number Article description 9370 KOR KOR MUX TELE Switch 4 2 2 Win TELE PROF 4 2 2 1 S5 4 2 2 1 1 Ground package Order number Article description 9372 PC S5 Win TELEPROF Software S5 Ground package single license 9372 PC S5 S Win TELEPROF Software S5 Ground package Subsequent license 9372 PC S5 F Win TELEPROF Software S5 Ground pack
39. only valid for data and speech operation When switching from speech to data operation the modem has to start with an initial value initial Baud rate in order to build up the connection This initial Baud rate corresponds to the Baud rate manual Following items are possible 12 1200 Baud 24 2400 Baud 48 4800 Baud 96 9600 Baud 33K 33600 Baud 2003 2011 by PI TIS 61 Operating instructions Tele Network 6 2 9 10 ISDN protocol For the connection to the digital ISDN system you should please note that there are 2 different protocols are possible e DSS1 Euro ISDN e 1TR6 national ISDN The national ISDN is today not so often used This was in earlier day a most used system but today not more All new ISDN system uses the newer form called Euro ISDN or DSS1 With this menu item you switch the protocol But be shure that after selectoing this menu item the device must be restartet 6 2 9 11 ISDN EAZ MSN The so called EAZ MSN is the device number of the TELE PROFessional ll on this telephone plug For the ISDN SO bus every client must have this address he will be recognized through this number So the TELE PROFessional ll knows that he will be meant and it will take the call Often the number of the telephone plug is also this number Please contact your supervisor of the telephone system to get this information So he can also change the ISDN property to modem this will be needed for this telephone plu
40. program that contains no derivative of any portion of the Library but is designed to work with the Library by being compiled or linked with it is called a work that uses the Library Such a work in isola tion is not a derivative work of the Library and therefore falls outside the scope of this License However linking a work that uses the Library with the Library creates an executable that is a derivative of the Library because it contains portions of the Library rather than a work that uses the library The executable is therefore covered by this License Section 6 states terms for distribution of such executa bles When a work that uses the Library uses material from a header file that is part of the Library the object code for the work may be a derivative work of the Library even though the source code is not Whether this is true is especially significant if the work can be linked without the Library or if the work is itself a library The threshold for this to be true is not precisely defined by law If such an object file uses only numerical parameters data structure layouts and accessors and small macros and small inline functions ten lines or less in length then the use of the object file is unre stricted regardless of whether it is legally a derivative work Executables containing this object code plus portions of the Library will still fall under Section 6 Otherwise if the work is a derivative of the Library you ma
41. rest of the numbers are host 94 2003 2011 by PI TIS Operating instructions Tele Network numbers within this network Possible network numbers for such a network are numbers between 1 and 126 which means that worldwide only 126 Class A Networks can exist So an IP Address belongs to a Class A Network when its first number is between 1 and 126 The American military network for instance is a Class A Network Within one Class A Network the corresponding network provider can freely assign the second third and fourth number of each IP Address As each of the three numbers can have the value between 0 to 255 a Class A Network provider can assign up to 16 7 million IP Addresses to hosts within his network The second highest hierarchy level are the Class B Networks The network number of such networks stretches over the first two numbers of the IP Address The first number of the IP Address of a Class B Network can have a value between 128 and 191 The second number can have values between 0 and 255 Thereby about 16 000 of such networks are possible As the numbers three and four also can have values between O and 255 a Class B Network can have up to ca 65 000 hosts First of all Class B Networks are assigned to huge firms universities and online services The lowest hierarchy level are the Class C Networks The first number of an IP Address can have the values between 192 and 223 The numbers two and three belong to the network number
42. socket then the PG TELE can communicate with the plc at the PG socket of the PLC TELE with this adjustment This menu item is also valid for the H1 L1 and L2 communication if these software options are released In this case the CP is connected to the PG socket of the PLC TELE The following adjustments are possible e Connect PG socket with PLC socket normal setting e Connect PG socket with PG socket 2nd plc or switch to CP connection 5 2 2 9 2 Break Tx line This menu item is valid for example for turning on the H1 In case the connected CP does not react anymore to the communication a break with adjustable duration can be sent to the CP Duration in seconds 0 to 30 5 2 2 9 3 Direkt Mode You can select this mode in order to realise a data transmission that does not correspond to a communication protocol specific for controls as for example the AS511 protocol of Siemens plcs For further Information please read chapter 7 5 Serial Extension Direct Mode 2003 2011 by PI TIS 41 Operating instructions Tele Network 5 2 2 9 4 Tele Switch With this option you can configure the tele switch device for the Tele Network devices The TELE SWITCH can be operated at the PLC or PG socket of a TELE Network device that is configured as PLC TELE In the PG TELE the following adjustments have to be made for calling a channel 1st line TELE SWITCH 2nd line xx to ChaNr yy xx PG or PLC with UP DOWN key yy Channel 00
43. still lines in the TELE these are sent to the plc The following is then in the target DW Number of the received bytes in KF format DW from here in KC the signs Transmission status 01h command is ready without mistakes 02h command is being executed but you have to check for TIMEOUT the command should be executed after 45 seconds 03h source module does not exist or is too short 04h target module does not exist or is too short 05h mistake the command has to be repeated 06h configuration DM does not exist 07h parameter fault 08h the partner device is not an ASCll subscriber O 2003 2011 by Pl TIS 117 8 6 3 Setup of the communication data module at the ASCII TELE DWO DW1 DW2 DW3 DW4 DW5 DW6 DW 7 118 KC data type of the source at the moment only DB possible DB data module IB input byte source DB number initial address of the source sector StartDWNr number of words Data type of the target at the moment only DB possible DB data module IB input byte target DB number initial address of the target sector StartDWNr number of words 2003 2011 by PI TIS Operating instructions Tele Network 8 6 4 Send data with the ASCll option The following criteria have to be fulfilled the ASCll subscriber is called AS in the following e The AS does not send OAH as st sign to the plc e All transmissions form the AS have to be finished with CR
44. terminal Please read the user s manual closely before installing the device There is no responsibility taken for damage due to incorrect connection or handling 2003 2011 by PI TIS 51 Operating instructions Tele Network 6 2 Konfiguration 6 2 1 Device Type With this option you can configure the TELE PROFessional ll in its ground configuration This configuration has following items e PLC S5 TELE e PG TELE e PLC S5 KOR MUX e PLC S7 300 400 e PLC S7 200 9K6 e PLC S7 200 19K2 e PLC S5 F Type e PLC PILZ e PLC Allen Bradley 52 The device is next to the plc control and is connected to it The device is next to the programming device and is connected to it The device is not connected directly to the plc but via a SIEMENS MUX 757 PG BUS dialling via a coordinator e g 923 C or via the IBX Bus Bus system of Pl with PG BUS dialling special type of PLC TELE The built in Multiplexer is not active in this operation mode This device is connected to a S7 300 400 plc This device is connected to a S7 200 plc and communicates with 9600 Baud on port PLC V24 This device is connected to a S7 200 plc and communicates with 19200 baud on port PLC V24 This device is connected to S5 plc especially a F Type This device is connected to PILZ PSSxxx plc you should connect the plc with its own programming cable This device is connected to a Allen Bradley SLC5 plc and communicates with the DH485 or DF 1 m
45. the data type for the correct conversion Boolean Bit unsigned int Word without sign signed int Word with sign DWORD Double Word without Sign signed DWORD Double Word with Sign real Floating point number 128 2003 2011 by PI TIS Operating instructions Tele Network The normings For the correct processing and displaying of the variable maybe a conversion is necessary This conversion can happen with normings You can define the necessary conversions here and later you can assign them to a message As normings usually happens frequently it is meaningful to manage them centrally Access rights Level Write Superuser Read View Superuser TELE PROF It P 1 no name Tnorming Junit Istate pic value 1 HMI value 1 pic value 2 HMI value 2 1 onon text O 0N1 0F F 0 00 0 00 0 00 0 00 2 Window state text O opened 1 closed 0 00 0 00 0 00 0 00 3 Degrees C linear 6 0 00 256 00 2048 00 256 00 4 3 steps text j D step0 1 step1 2 sten2 0 00 0 00 0 00 0 00 A A AA 1 1 i PPPE j near 0 00 0 00 0 00 0 00 The meaning of each column norming Column Usage Name Own notation Norming Currently there are two supported norming types either linear or text linear means the value from the PLC has to be converted In this case the fields plc value 1 HMI value 1 plc value 2 HMI value 2 are texts which means tha
46. the different pager types for foreign countries DW 1 DW 10 DW 11 DW 20 DW 21 DW 30 DW 31 DW 40 DW 41 DW 50 DW 51 DW59 DW60 DW141 104 Number for the first pager in KC with an E at the end There are only maximum 19 characters possible For example 0171992282E Is the first character an E so is the following number not guilty A special opportunity for SMS pager is that you can with one call send the message to more than on sms pager This is only for SMS Pager for the other one there is no possibility If you use the Skyper or Scall where you have edit the pager number in the subscriber database there is no look for the pager number in this DB Attention This entry must exist in every case Number of the second SMS PAGER only when 1 or 0 in DWO Number of the third SMS PAGER only when 1 or 0 in DWO Number of the fourth SMS PAGER only when 1 or 0 in DWO Number of the fifth SMS PAGER only when 1 or 0 in DWO not used Text of the message Only maximum 160 characters Pay attention that when you use pager with numeric data For e g Scall Quix and so on This numeric data is only from 20h to 7Fh ascii code available All the other data is unguilty The end of the data is a 00h in this DB You have to look for the different maximum data characters for the different pagers In this case your message is sent not correctly Maximal data characters are 160 characters
47. the other device has a activated pin and there was no login yet command function AT E Direct mode without handshakes is activated It will be used the in the PG TELE defind parameter for source and destination com After you have activated this mode the ending will be only reached you change the status of the DSR line ALT H for ZOC or TELIX Or you press any key on the TELE PROFessional ll AT F see for AT E only with activated handshakes RTS CTS result OK Direct mode is activ ERROR Function not OK maybe source com not correct defined Direct mode off Direct mode is deactivated somebody with the keypad or DSL line You must login Function can be activated the other device has a activated pin and there was no login yet 138 2003 2011 by PI TIS Operating instructions Tele Network command function AT Gx Only for Siemens TELE PROFessional ll Changes the plc type x stands for the plc type Possible values Attention These switch need a few seconds time for to switch X Meaning 0 SIMATIC S5 1 Not for use 2 SIMATIC S5 KOR MUX IBX 3 SIMATIC S7 300 400 4 SIMATIC S7 200 9K6 5 SIMATIC S7 200 19K2 6 SIMATIC S5 mit F Typ result OK All is OK ERROR Nothing is OK please check the parameter you used You must login Function can be activated the other device has a activated pin and there was no login
48. the transmission While the programming is in process do not disconnect the device from the voltage supply since then the complete programme becomes invalid If the programme is invalid the device reports an ERROR If this message appears the device has to send to your local distributor After the programming the device executes a warm Start and after that it reports with the new software release yet with the same configuration 2003 2011 by PI TIS Operating instructions Tele Network 5 2 2 5 11 Remote Config ON With item you can activate the configuration of the remote device If you had activated this item and you change any parameter in the konfiguration you change it in the remote device and not in this device you are in front of This item is so long active until you deactivate this item Be sure that you switch off the remote configuration after ending of the edit because when you mean you are ready with the configuration and you want to edit your own configuration you overwrite the remote configuration and so ist possible you can t get a connect after this operation Before you start the remote configuration you should have the same firmware in both devices Please note that the called device is a PLC TELE because this is only from PG TELE to PLC TELE possible 5 2 2 5 12 Remote Config OFF With this item you can deactivate the configuration of the other device the remoet device After you are ready for
49. then press ENTER or use the cursor right key In case you have confirmed a menu item you do not want you can cancel this selection by pressing the cursor left key In case there have already been any modifications these are not saved then If you want to save a modification just press ENTER If the tele network device doesn t recognize the keyboard input the following causes are possible At first the communication between both modems is so bad because the telephone line is so bad so the modems had to repeat more and more the same blocks of data then there is not so much time to recognize the keyboard input But when there is no problem with the telephone line more the input of the keyboard is OK You have a connection with a tele network device which modem doesn t work correctly So your modem tries to send the data blocks to the other modem but there is O 2003 2011 by Pl TIS 17 Operating instructions Tele Network no response and so it tries it the whole time When you have this problem your device has the same response as the first case Remove the telephone plug from the device so that the connection cuts off When you have a lot of time you can press the key codes and wait a long time you can see under INFO REMOTEVERSION and there you see nothing so you know that the device of the other side doesn t work correctly You are at the PLC TELE and on the other side there is a force block or force variable i
50. this menu item you define the address of the TELE PROFessional ll as a bus client This address must be a unused address for the bus If you use the default address 0 be shure that no PG with this address will be in the bus too If you start a connection from the office to the plc the devices uses the address you configured in your programming software If your tele service is ready the device uses the configured address Possible addresses are from 0 up to 126 O 2003 2011 by Pl TIS 53 Operating instructions Tele Network 6 2 4 4 MPI OnBoard HSA With this menu item you configure the HSA highest station address of the connected bus Please note that a to big HSA will slow down the speed of communication to the bus So in your software there will be the baudrate for the bus system configured Have you configured the fis baudrate to No so the baudrate from the programming software is be used If you re a beginning to programm a plc it is better for you because so you are able to change the baudrate as you like Have you configured this item to Yes the device uses the configured baudrate of the TELE PROFessional Il and ignors the baudrate from the software Possible Values 15 31 63 und 126 6 2 4 5 Fix OnBoard Baud While you have tele service to a plc the PLC Tele is for your software a PC MPI adapter So in this driver you can configure the baudrate of your bus system Have you configured the fi
51. user s manual closely before installing the device There is no responsibility taken for damage due to incorrect connection or handling 5 2 2 7 Menuitem Configuration With this option you can configure the TELE PROFessional ll in its ground configuration For further informationen please read chapter 6 2 Konfiguration 36 2003 2011 by PI TIS Operating instructions Tele Network 5 2 2 8 Menu item Options 5 2 2 8 1 Pager TELE 5 2 2 8 1 1 PAGER operation With this menu item you can turn the PAGER TELE operation on or off 5 2 2 8 1 2 PAGER flag With this menu item you can input the common flag word for the data communication Use even numbers only e g FW 122 Only 0 to 254 5 2 2 8 1 3 PAGER COM DB With this menu item you can set the communication data base DB in order to set parameter values to the data flow and source at the PAGER operation 2003 2011 by PI TIS 37 Operating instructions Tele Network 5 2 2 8 2 PLC ASCII TELE This menu item is only activated if the TELE Network device has a plc option or an ASCIll option 5 2 2 8 2 1 Modem Control In this menu item you can adjust how the communication between the plc and the modem is carried out NO plc does not have the possibility to control the modem with flag word PLC TELE LINK and plc have a common flag word for controlling with digital I O PLC TELE LINK and plc communicated via the digital I O level 5 2 2 8 2 2 Modem
52. version 2 see below Special exception for linking OpenVPN with OpenSSL In addition as a special exception OpenVPN Solutions LLC gives permission to link the code of this program with the OpenSSL library or with modified versions of OpenSSL that use the same license as OpenSSL and distribute linked combinations including the two You must obey the GNU General Pub lic License in all respects for all of the code used other than OpenSSL If you modify this file you may extend this exception to your version of the file but you are not obligated to do so If you do not wish to do so delete this exception statement from your version LZO license LZO is Copyright C Markus F X J Oberhumer and is licensed under the GPL Special exception for linking OpenVPN with both OpenSSL and LZO Hereby grant a special exception to the OpenVPN project http openvpn net to link the LZO library with the OpenSSL library http www openssl org Markus F X J Oberhumer OpenSSL License The OpenSSL toolkit stays under a dual license i e both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit See below for the actual license texts Actually both licenses are BSD style Open Source licenses In case of any license issues related to OpenSSL please contact openssl core openssl org Copyright c 1998 2003 The OpenSSL Project All rights reserved Redistribution and use in source and binary forms with or with
53. work with an existing project of the PLC The virtual PLC must have the mpi address configured in the menu item on board mpi address of the web interface of the TP Il possible for PC adapter MPI or PC adapter 2003 2011 by PI TIS PG TELE 192 168 1 200 yes 255 255 255 0 172 16 0 3 172 16 0 4 yes PLC S7 300 400 192 168 2 200 yes 255 255 255 0 172 16 0 1 172 16 0 2 yes 1 for e g yes yes lt here select the number of the direct connected plc gt lt here select the number of the direct connected plc gt 7 7 2 S7 connected to ethernet port of PLC TELE S7 300 400 7 7 2 1 PC connected to PG TELE via RS232 to PG V24 port For this situation there will be no reason to solve this communication 7 7 2 2 PC connected to PG TELE via ethernet to the ethernet port Office side device side IP address use ethernet subnetmask Subnet mask Isdn ip analogue ip router mode machine side device side IP address use ethernet subnetmask Subnet mask Isdn ip analogue ip router mode on board mpi address note For Step7 software PG TELE 192 168 1 200 yes 255 255 255 0 172 16 0 3 172 16 0 4 yes PLC S7 300 400 192 168 2 200 yes 255 255 255 0 172 16 0 1 172 16 0 2 yes O for e g is standard for a programming device Work with your project of the plc Please note the correct ip addresses Not possible for PC adapter MPI or PC adapter Profibus 110 2003
54. your PG TELE and activate the ProTool 7 17 Now you can transfer your project to your OP After programming your OP you can end the ProTool Option with pressing the lt key Now your TELE Network device is in the standard programming mode for example for the S5 or the S7 By this way you can also programm the C7 too 8 13 2 Programming with ProTool For programming the bigger Ops like OP27 37 you can t use the software ProTool lite For this OPs you use ProTool This OPs can be programmed only via MPI Protocoll because the standart protocoll of programming is not modem like For this you must configure following Connection of PLC TELE with MPI PPI cable and MPI Netz Adapter to the OP Change devicetyp of PLC TELE to PLC S7 300 400 The ProTool Software must be installed in the simatic manager In your project or the OP must be activated the MPI Interface for transfer After connect of the telefon line you restart the OP for the transfer mode Now you start your transfer with your ProTool Software via PC Adapter and 19200 Baud After the OP is programmed you disconnect the telefon line and your OP is ready to work This Menthod works with S5 OPs too But you need for this way the simatic manager for Step 7 This is only way to programm OPs 136 2003 2011 by PI TIS Operating instructions Tele Network 8 14 Controlling of the TELE Network Devices with TAPI Interface The Tele Network Devices can be controll
55. 0 DW 14 0 DW 15 200 DW 16 0 end is recognised For S7 adress name type value 00 STRUCT 0 0 9 20 0 5 22 0 4 24 0 200 26 0 10 28 0 30 0 m 32 0 INT 34 0 name END_STRUCT 100 2003 2011 by PI TIS Operating instructions Tele Network 7 4 1 3 Sending a fax with the FAX TELE function If you want to send a fax you have to define a communication flag word and a communication data module in the TELE LINK The communication flag word always has to be an even number in the range of 0 2 254 In order to start the transmission and to call the subscriber 4 the plc now gives the following command to the communication flag word f ex FW 10 0104h The remaining data and the actual communication are executed according to the scheme defined in the DB Please note that you have selected the pg mux mode for pg mux see chapter 6 2 7 PG MUX Mode Only for PLC TELE and S5 7 4 2 SMS 7 4 2 1 Messages of the plc sending to a pager Attention Switch PAGER operation only to YES when you have set and proofed all parameters With the PAGER option you can send from the plc in the plc defined data the actual build of flags and DB to a pager This option is possible in all TELE Network Devices with Software Version 4 00 or bigger with S5 S7 Firmware You have to look for the speciallities of the different pagers Following pager are supported with this option SMS to Handy Cityruf alphan
56. 1TR6 national ISDN This protocol has to be configured im the configuration menu After this you have to restart the device You must configure an EAZ MSN number of your ISDN port This means the addres of this device in your SO bus While the ISDN port is a bus structure so every client of this bus needs a own address This address is the EAZ or MSN So the device knows this address and can ring and lift up if this address will be called Sometimes the configured EAZ or MSN is the same number of this telephone port often a normal number between 1 and 999 This address you get from your supervisor of the telephone device ATTENTION A communication with ISDN is without MSN EAZ is not possible 2003 2011 by PI TIS 147 9 4 4 LAN connector This connector is an autosensing 10 100 Mbit s connector For the connection to a Hub or a network connector you should use a socalled patch cable both sided RJ 45 1to1 shielded For the direct connection to a PC you should use a cross link cable for this connection 9 4 5 USB connector On this USB 1 1 compatible connector can be plugged slaves like memory stick or digital cameras But if you want to connect slaves like this you should get support from your dealer because they must check it and integrate this slave into the firmware of the device 148 2003 2011 by PI TIS Operating instructions Tele Network 9 4 6 PCMCIA connector only for version H
57. 2 168 0 10 herstellen 9 X A TELE Prof II Benutzername e Kennwort C kennwort speichern After successfully logging in the browser will store your login data during the current session to this device The logout will not be done until you close all browser windows which are connected to the device 16 2003 2011 by PI TIS Operating instructions Tele Network 5 2 On Site Configuration 5 2 1 Integrated Keypad With the 6 integrated key of the keypad you will be able to configure the device Inside of the keypad there is a display with 2 rows a 16 columns integrated With the ESC key you can return to the main menu Vor inbetrebratme Becienungeanieitur Reed manual before nstallatrior Taste Bezeichnung _ Beschreibung Y ENTER Change of menu and confirm of input a LEFT Go one menu level back Discarding input Input will NOT be stored RIGHT Call Submenu tT UP Selection of a menu item Increase of a value y DOWN Selection of a menu item Decrease of a value Esc ESCAPE Cancel of the currently executed function Go one menu level back Cancel of the input Input will not be stored In order to get from menu level to menu level use the cursor up or cursor down keys You can select a certain menu item by pressing ENTER or by using the cursor right key You are in a submenu now and can select a sub item in the same way cursor up down and
58. 2 Menutree This menu item is called First config and its menu structure is shown in the following Language German English Device type PLC S5 TELE standard S5 PG TELE office device PLC S5 KOR MUX PLC S7 300 400 standard S7 300 400 PLC S7 200 9k6 PLC S7 200 19K2 PLC S5 F TYPE PLC Pilz standard for PILZ plc PLC Allen Bradley standard for AB plc MPI OnBoard Y N Yes default No MPI OnBoard Baud 9 6 kBit s 19 2 kBit s 45 45 kBit s 93 75 kBit s 187 5 kBit s Default 500 kBit s 750 kBit s 1 5 MBit s 3 Mbit s 2 6 Mbit s 12 Mbit s OnBoard MPI Adr 000 default MPI OnBoard HSA 15 l 31 default 63 126 Fix OnBoard Baud Yes No default 2003 2011 by PI TIS 45 Operating instructions Tele Network MPI Profibus MPI Bus default Profi DP Std Profi DP FMS MPl cable Baud 19200 default 38400 57600 115200 ISDN EAZ MSN 0 9999999 Ethernet IP XXX XXX XXX XXX ISDN IP Adresse XXX XXX XXX XXX Analog IP Adr XXX XXX XXX XXX Analoguemodem German complex default i USA 600R system Dialmode Tone default Pulse Extension Mode Yes No default Outline Code 0 1 2 3 4 5 6 7 8 9 1 gt H X W gt Count of rings 0 1 2 3 4 5 46 2003 2011 by PI TIS Operating instructions Tele Network With the UP or DOWN keys you can go through the menu tree Press ENTER in order to select a menu item Now use the cursor up or cursor dow
59. 2 up to 12 MBaud For S7 200 you have to use a RS232 PPI cable like the MPI PPI cable connected on the port PLC V24 The connection to a not provided plc is also possible For this purpose the device has 2 9pin D SUB plugs one male the other female From the PC you can connect to the TELE PROFessional with a standard serial cable 9pin 1to1 The other plug male has the same pinning like a PC so you connect the plc with its own programming cable The device has also 2 USB ports For example you can connect a memory stick in the moment not provided for the extension of the memory of the device The provided standard of the usb port is USB1 1 Or you can use the 2 PCMCIA Slots only for version H for some special functions You can connect a Handy to the serial 9pin male port You use for this the standard download cable of the handy If you make S7 teleservice you don t need this port because you have connected the plc to the on board mpi profibus port For teleservice of the S5 there must be some changes The plc is not connected to the PLC port it is connect with the cable CP Kabel article number 9359 90 to the multiplexed PG port It is very important that the handy has an own number for this data transfer you need for this a special kind of the contract with your provider The TELE PROFessional ll is connectable with a patch cable to the Ethernet So you can make a prolongation of your home Ethernet with the Ethernet of the plc si
60. 3K Connection with Recall see chap Fehler Verweisquelle konnte nicht gefunden werden M12 M144 call to a mailbox no tele network device see chap Fehler Verweisquelle konnte nicht gefunden werden ISDN connection with the ISDN port RSDN connection with Recall mode with ISDN port If you have to edit a telefon number with more than 16 characters you can do it with following way You edit for example subscriber 8 edit the telefon number with 15 characters then the special char gt and edit in subscriber 9 the rest of this telefon number You can select letters numbers or other adjustments by using the cursor keys UP DOWN and the cursor position if possible by using the cursor keys RIGHT LEFT If you have activated the return call function Rxx Baud you will then have the possibility to input the RC PNr return call prefix number If you have activated the modem call function you had to configure the connected PC by the TELE PROFessional ll at the V24 Connector with following options 19200 Baud 8 Data Bit 1 Stop Bit No Parity and RTS CTS for handshakes 26 2003 2011 by PI TIS Operating instructions Tele Network 5 2 2 5 Menu item online action 5 2 2 5 1 Hang up With this menu item the modem disconnects an existing connection i e it hangs up 5 2 2 5 2 Lift With this menu item the modem receives incoming calls This is only the case if the adjustment number of signals before pick
61. 55 255 255 0 124 11111111 11111111 11111111 11000000 255 255 255 192 126 The network part is usually continuous without intercostals zeros 2003 2011 by PI TIS 95 7 3 3 Standard Gateway If an IP Address is tried to reach which is not in the own network in the first place the PC doesn t know where to find the address Therefore a Standard Gateway can be defined the Standard Gateway can be defined in the network settings If such a Standard Gateway is configured the PC looks for remote IP Addresses via this device 7 3 4 PPP connect for the router function In the menu item Configuration acces code modem user you can define user for the modem connection The item has 4 parameters e complete name gt this is the name for the data set e username gt this is the name for the user e password gt password for the user e direction gt direction for the account Please check that the password is written down correctly Please check uper and lower case Possible values for the direction e Dialln gt This data is only for the acces for a standard tele service e DialOut gt The configured data is only for the login to the router e Dialln Out gt data for login to the router and acces for tele service In the menu item configuration acces code dialing protect you can activate this acces code for the modem connection If you have defined a modem user with the direction Dialln Out the dialing p
62. ELEPROFS be opened any time by clicking Einstellungen _Ysschnis watien Setti ngs P virtueller COM Ports s7com come y S7 COM Via this COM Port you can S5C0M COM7 z access the S7 which iS piemodecom coma z connected to your PLC TELE g IV ISDN Modems f r Analog TeiInehmer anzeigen IV Analog Modems fiir ISDN Teilnehmer anzeigen S5 COM Via this COM Port you can Fe 1 access the S5 which is tnav7atechattrowendg o E connected to your Abbrechen PLC TELE Direkt Mode COM This COM Port is for serial ARTO extension which means that no waiesn Mess Emetet protocol inspection will take Bas FosenModenssraisaten place Consequently you can essa connect any desired serial j device 2 Configure your modem under Start Settings System configuration Telephone and Modemoptions 72 2003 2011 by PI TIS Operating instructions Tele Network 4 By clicking the symbol next to the entry number you can edit the corresponding entry respectively create a new entry By clicking the cross the corresponding entry will be deleted PG TELE Se 3 When you have configured your modem click phone book pha KITS 1 5 Create a new entry in which you have defined the number of your Tele Professional ll and then click on the Floppy Disc Symbol to store the entry phone book no
63. HE H1 BUS occooccccocccnccnccnconcnnccnnnncononocononnnns 113 8 4 OPERATION OF SEVERAL PLCS VIA THE L1 BUS 0ccccceeceeeeceeceeeeeeeeeeeeeeeeeaes a 8 5 OPERATION OF SEVERAL PLCS VIA THE L2 BUS 0ccccceeceeceeceeceeeeeseeeeeaneceeans 114 8 6 SEND DATA FROM THE PLC TO A MODEM SUBSCRIBER 0sccceeecceeeceeeeeeeeeeeeaes 115 8 6 1 Setup of the communication word between plc and TELE Network 115 8 6 2 Setup of the ASCII TELE f ag oocococcoconcconcococononoccocnonnnocanonnnnonannnnnonnns 117 8 6 3 Setup of the communication data module at the ASCII TELE 118 8 6 4 Send data with the ASCII OptiON ooooooooccooooccooooococonanononoconnnnnnnnnnos 119 8 7 COMMUNICATION WITH A MAILBOX MODEM oocccccccccccnccncnnnnnnnnnnnnnn nn 120 8 8 COMMUNICATION WITH ANSP ii 121 8 9 COMMUNICATION WITH EXTERNAL HANDY OR MODEM occoocccccncccccnccnconcnncononocononnnos 122 8 9 1 Connecting a handy to a PG TELE oooccococoninicicinonoconononnnnnnnnnnnnnnnnnnnnns 122 8 9 2 Connecting a handy to a PLC TELE SO ceros 122 8 9 3 Connecting a handy to a PLC TELE S7 300 400 2ccccccceeceeeeeeeeees 123 8 10 FREVA E tratada RAE TAREA TA EAT AAA TAE 123 SFE MODULES ls da it ico 124 8 12 COMMUNICATION WITH TELE SWITCH ooccconccnccnccnccnccncononnconnnnconnnncononocononnnos 135 4 2003 2011 by PI TIS Operating instructions Tele Network 8 12 1 Function of the TELE SWITCH as MUX com
64. HER PROGRAMS EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES 162 2003 2011 by PI TIS Operating instructions Tele Network 2 GNU LIBRARY GENERAL PUBLIC LICENSE Version 2 June 1991 Copyright C 1991 Free Software Foundation Inc 51 Franklin St Fifth Floor Boston MA 02110 1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed This is the first released version of the library GPL It is numbered 2 because it goes with version 2 of the ordinary GPL Preamble The licenses for most software are designed to take away your freedom to share and change it By con trast the GNU General Public Licenses are intended to guarantee your freedom to share and change free software to make sure the software is free for all its users This license the Library General Public License applies to some specially designated Free Software Foundation software and to any other libraries whose authors decide to use it You can use it for your libraries too When we speak of free software we are referring to freedom not price Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software and charge for this service if you wish that you receive source code or can get it if you want it that you can change the software or use pieces of it in new free programs and that you kno
65. LE Here you can input the prefix number plus the number with which the TELE Network device that requires a return call can be reached Possible Entries max 16 chars Telephonenumber This menu item is only active with the PG TELE 6 2 12 1 Max Connect time With this menu item you determine the maximum duration of the connection After this maximum the connection is disrupted The duration is set in minutes The maximum is 60 minutes This item will be ignored if you define this time with 0 64 2003 2011 by PI TIS Operating instructions Tele Network 6 2 12 2 Max Idletime Here you determine the maximum duration of the idle operation of the PG The time span starts when there is no exchange of data between the plc and the PG anymore After the maximum time is up the connection is disconnected The duration is set in minutes The maximum is 60 minutes This item will be ignored if you define this time with 0 6 2 13 Access code 6 2 13 1 PIN device local Password for the protection of the configuration of your TELE Network device PLC TELE or PG TELE The parameters of the device can only be changed after the input of the correct password local gt means the device in front of you Max 6 characters 6 2 13 2 PIN plc local Password of the device that is located at the installation PLC TELE This password protects the connected plc control against unauthorised access via the telephone line
66. OWSED 1 cccccccccsseeeeeeeeeeeeeseeeaensesseeneeess 14 5 2 ON SITE CONFIGURATION 0cceeceecceecceccecceeececceceeeccucceeeeeeceeeaeeeueceeeaeeceesaneneeeass 17 oli Keypad AA O N 17 DIZ D MONUUCC ta a ta datos 19 52 21 Menu item messages ii Aaa 25 5 2 2 2 Menu item Hang Upa eienenn e iio sj geens 25 5 2 2 3 Menu item Select SubsScCriber oo onnccconnncccnoccccnnnacnnonanocononaco no nano nono nn conc tesine anno nr nn nn arc n cnn rana nannnns 25 5 2 2 4 Menu item Edit subscriber ooooconnccccncccccnncccononanononanocononaco conocio nonano nono anno nnn ana nnnncn conan nc nn nn nnana ananena 25 5225 Menu item ea A A tada 27 5 2 2 6 Menu item First CONO oia 32 5 2 2 7 Menuitem Configuration id 36 5 2 2 8 Menu item Options erie aaeeea ereere raona aces cece eee eaaeaeeeeeeecaaaaeaecaeeeeecgeeaaaeaeeeeeeeeaaeaeseseeseneaeeeeeeeees 37 5 2 2 9 Menu MEM Special ici didacticas 41 ATA E O aa T E Ea e ats 42 BD Ded noaea a aon thom a e a a e a a ALA 43 5 3 STATUS WITH LED E E EEEE EEE E EEE EE EEE EEE E E E AE E AEA EE 44 6 IMPLEMENTING 22 00 ccecceeceeccneceecceeceeceeccneceeccuseeeceascusceeceuseneceaseneceeseuseneseeseneees 45 6 1 QUICK CONFIGURATION QUICK ENTRANCE ccceeccecceeeceececeeeececcseeeeeueeeeeeeeeass 45 6 2 KONFIGURATION i lao dada drid 52 6 2 T D vice ES 52 6 2 2D vicename enen a a cuss lata EOSS 53 6 2 3 Router Mode a a a a o 53 6 24 MPI O B OAA a a a aa R A dyes AE aid dea
67. Operating instructions TELE Network user s manual english for TELE PROFessional Version 1 5 O 2003 2011 by Pl TIS Operating instructions Tele Network Inhalt 1 od ad y i E E SEEE EE E E a ans opos Ys 6 2 DESCRIPTION unirnos 7 3 SYSTEM REQUIREMENTS v 2 2ccecceeccneceeccecceeceeccneceeccnseneceeseneceeceusensceaseneeesseuseness 8 DH REQUIREMENTS pe aeaea edi 8 OI ZIFEATURES I cents create hoe iu aia he ia Neha Ne os Ae a 8 4 SCOPE OF DELIVERY AND ACCESSORIES 2 ccscceeceeceneceeccneceeceeseneceeseneeees 11 4 1 SCOPE OF DELIVERY ecceccecceceeceececceeaecueceeceeaeeaecueceeaeeaecaeceeseeaeenecueseeaesaeeneeneas 11 4 2 OPTIONAL ACCESSORIES ceccecceecceccecceeececcenecueceeeaeecueeaeeceeeeeeaueceeseeeueseeeneesees 11 4 2 1 Interfaces SWITCHES o rrr e een ra or eront or arenero 11 4 2 2 Win TELE PROP met e e r a e r ri 11 ADD AES EEE AA E N E E E T E ESET 11 DD DS E E E E E E E AET lice E O 11 4 2 3 PLC connection CADIC 1 ccc ce ccccecceccecceccecnecnececceeascaeseceessenseeseeseensenesnesees 12 4 2A ACCOSSOMIOS A elo Pr eon ATE A ela coe 12 A241 Mounting accessorie Siria e eare io 12 4242 Other ao eS OOO a aa dietas dde a aa a aaa aaa nanoa aat Saada niade aT 12 424 3 Phone aO e SOE S e aT aa E aaa a a a a coed ae paa o ana aN 12 5 HANDLING AEA AAE E A TE A T A E A A aladas 13 51 WEB BROWSER cundo died tent load nd Soi toe a d tod Lobo Pt Song dans 13 5 1 1 Access protection via WEB BIr
68. PLC TTY PLC TTY connector for direct connection to a S5 PLC via 1to1 cable ON OFF switch ov PCMCIA Powerconnector with ground pin 142 2003 2011 by PI TIS 9 4 2 Analogue modem connector Operating instructions Tele Network When connecting the telephone the cable with the black TAE plug is plugged in the telephone socket N contact Please note that with some plugs a locking device has to be removed with a screwdriver in order to extract the plug from the TAE socket The other side a so called western plug has to be plugged with the ejector up in the small hole of the modem You will hear how the locking device latches In order to extract the western plug simply press down the locking lug and extract the plug Normally you can use every analogue connector but be shure that this analogue line the both lines A and B are connect to the middle contacts of your western plug RJ 11 9 4 2 1 Assignment of the connection pins of the TAE SOCKET E B2 A2 for N und F connection A B W 1 2 3 4 5 6 Ny Fy F2 6 5 4 3 2 1 A2 B2 E W B A for F2 connection Connections A B are absolutely sufficient for a modem connection only without telephones With pulse dialling and calling the line with earthing key the connection E additionally 2003 2011 by PI TIS has to be connect to frame at the telephone in
69. Program or any portion of it thus forming a work based on the Program and copy and distribute such modifications or work under the terms of Section 1 above provided that you also meet all of these conditions a You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change b You must cause any work that you distribute or publish that in whole or in part contains or is derived from the Program or any part thereof to be licensed as a whole at no charge to all third parties under the terms of this License c If the modified program normally reads commands interactively when run you must cause it when started running for such interactive use in the most ordinary way to print or display an an nouncement including an appropriate copyright notice and a notice that there is no warranty or else saying that you provide a warranty and that users may redistribute the program under these conditions and telling the user how to view a copy of this License Exception if the Pro gram itself is interactive but does not normally print such an announcement your work based on the Program is not required to print an announcement These requirements apply to the modified work as a whole If identifiable sections of that work are not derived from the Program and can be reasonably considered independent and separate works in them selves then this License and its terms do not apply to those secti
70. RTIES PROVIDE THE LI BRARY AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUD ING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU SHOULD THE LIBRARY PROVE DEFECTIVE YOU ASSUME THE COST OF ALL NECESSARY SERVICING REPAIR OR CORRECTION 16 IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER OR ANY OTHER PARTY WHO MAY MODIFY AND OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE BE LIABLE TO YOU FOR DAMAGES INCLUDING ANY GENERAL SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES 2003 2011 by PI TIS 167 3 Other licenses ElinOS Embedded Linux distributed by SYSGO AG www sysgo com In the Tele Prof ll is used the Embedded Linux ElinOS collected by the company Sysgo www sysgo com The in ElinOS used software technologies and programmes are tied in part to the GENERAL PUBLIC LICENSE OpenVPN license Copyright C 2002 2005 OpenVPN Solutions LLC lt info openvpn net gt OpenVPN is distributed under the GPL license
71. Rings This menu item sets the number of rings after which the TELE Network device should pick up e 0 With this adjustment the modem does not pick up independently With the menu item pick up you have to make the modem pick up manually e 1 5 Modem picks up after the adjusted number of rings The operation of these remote maintenance units is only allowed if a supervising person is present who can intervene in the installation at any time Please do not intervene in running programmes without visual communication or control Before installing the TELE LINK Network devices please connect them by all means with earthing PE at the casing or at the screw terminal Please read the user s manual closely before installing the device There is no responsibility taken for damage due to incorrect connection or handling 6 2 9 4 Analogue Modem The buildin modem can be used world wide It has 2 approavals the european TBR21 and the american FCC The different is that the american system has its base with 600 Ohm the european system a complex system e German complex The connected telephone system is complexed e USA 600R The connected telephone system is 600R With this selection you should work in the USA and the other world but not in Europe If the modem picks up but the modem noise is not hearable then you should change the modem type 6 2 9 5 Dial mode In this menu item you can choose between two different dialling
72. S7 via standard MPI cable with the MPl connectors or the cable with article number 9379 1 e compatible with SIMATIC S7 200 plc connection of PLC TELE by S7 via MPI PPI cable or ppi adapter e ONLINE with the plc at the customer in a few seconds e suitable for industrial use and in agreement with CE e integrated HIGH SPEED modem with LineQualityControll Functions shorten LQM e integrated ISDN connector for Euro ISDN DSS1 or 1TR6 e 2 PMCMIA slide in unit for PCMCIA plug in cards only for version H e Can be operated by all original and compatible programming devices e second interface select either Mulitplex operation for the operation of a 2 PG PC control device or as a connection for a 2 plc CP for L1 L2 H1 from the PG TELE PLC 1 or PLC 2 can be switched only for S5 devices 8 2003 2011 by PI TIS Operating instructions Tele Network e supports the operation at the H1 L1 and L2 with reference to bus dialling e supports the operation KOR MUX of Siemens as well as PG BUS e operation software is saved in the flash memory which makes the updating of the software easier e absolutely simple to set parameter values e module which checks all the device functions and the voltage supply e the electronics to the telephone network to the external voltage supply to the plc and to the programming device are dc insulated e compact device in a metal casing e easy mounting into the switchboard e
73. a modem analogue or ISDN The virtual tunnel addresses are almost any desired they must be private addresses They even should come from another block than the real addresses so the routing will be easier real and virtual networks are easy to differentiate 2003 2011 by PI TIS 79 Private Address Normal public IP Addresses are worldwide unique Only like this a packet can find its correct destination In contrast to this the private IP Addresses are only valid in local networks they will not be routet into the public internet That s why many networks can use the same private addresses For this purpose several IP ranges are reserved 10 x x x and 192 168 z z as well as 172 16 y y to 172 31 y y The communication basically is over UDP merely you give the Port over which you want to communicate The Ports 9999 and 9998 should not be used as they are used by the TELE PROF II As default 1194 will be set If you are using a firewall make sure this Port is free in this case UDP 1194 If you want to communicate with the TELE PROF II from a PC over an OpenVPN connection make sure that these settings are configured in the firewall of your PC too 7 1 3 3 3 3 Access authorization Who is allowed to build an OpenVPN Connection How can the Access be controlled Principally everyone who has got the certificate and the IP Address of the TELE PROF ll can build a VPN connection and access the device This is comparable with when you
74. address 5 IP address 192 168 1 54 rack number 0 slot number 5 108 2003 2011 by PI TIS Operating instructions Tele Network 7 7 Possible Connections for S7 for TP Il 7 7 1 S7 connected to MPI PROFIBUS port of PLC TELE S7 300 400 7 7 1 1 PC connected to PG TELE via RS232 to PG V24 port Office side device side IP address use ethernet subnetmask Subnet mask Isdn ip analogue ip router mode machine side device side IP address use ethernet subnetmask Subnet mask Isdn ip analogue ip router mode on board mpi address note for Step7 software PG PD Port PG TELE 192 168 1 200 yes 255 255 255 0 172 16 0 3 172 16 0 4 yes PLC S7 300 400 192 168 2 200 yes 255 255 255 0 172 16 0 1 172 16 0 2 yes O for e g is standard for a programming device PC adapter MPI or PC adapter Profibus Properties correct COM PORT of PC 7 7 1 2 PC connected to PG TELE via ethernet to the ethernet port Office side device side IP address use ethernet subnetmask Subnet mask Isdn ip analogue ip router mode machine side device side IP address use ethernet subnetmask Subnet mask Isdn ip analogue ip router mode on board mpi address note for PLC TELE S7 CP emulation Use default dest mpi address Default dest mpi address PLC MPI Addr For FAX SMS Data For Step7 software Work with your project use inside the project a virtual PLC and a virtual CP You can only
75. ag edeuese 106 7 5 2 Dest COM cia i a Oa ee a a a 107 7D Dir ct Mode ON otra 107 7 5 4 Direct Mode On with HW wisn aise A odontal eked 107 7 6 S7 CP MODE EMULATION o 108 7 7 POSSIBLE CONNECTIONS FOR S7 FOR TPIl cc ssecccesecccssececseeecsseceeaseeeees 109 7 7 1 S7 connected to MPI PROFIBUS port of PLC TELE S7 300 400 109 7 7 1 1 PC connected to PG TELE via RS232 to PG V24 port coocccooccccconoccnonononcnnnnoncnano non nnnnn cn nnnnnnnnnnnnos 109 7 7 1 2 PC connected to PG TELE via ethernet to the ethernet pOlt oooocccnnccccnonoccncnonancno nono ncnnnancnnnnnanos 109 7 7 2 S7 connected to ethernet port of PLC TELE S7 300 400 ccccee 110 7 7 2 1 PC connected to PG TELE via RS232 to PG V24 port coocccooccccnonoccnonononcnononcnonono cnn n non nnnnnnnnnrnnnns 110 7 7 2 2 PC connected to PG TELE via ethernet to the ethernet port ccccccncncnoncnoneneneninininininininininos 110 8 SPECIAL FUNCTIONS cccccsesseeecccesseeeeecenseeeeeeenseeeeeeaseeeeeeaaseeeeeonnseesseeensees 111 O RRC ALL IMO es a rea 111 SA PEO TELE A a eh Vs CALMS 111 NA EE ala celo 111 8 1 3 WSC TOCAN MOS ota 112 8 2 OPERATION OF SEVERAL PLCS AT ONE TELE NETWORK DEVICE occcoccccccccncccccnnnno 112 8 2 1 Operation with Siemens MUX T OT ioocccocococccoconoconocononncnonononcnnnnnnnnnnnnnnnnnnos 112 8 2 2 Operation with intelligent Bus terminal IBX ccccccsseeeeeeeeeeeeeeeeeeeneeees 112 8 3 OPERATION OF SEVERAL PLCS VIA T
76. age company license 4 2 2 1 2 Add on packag e Order number Article description 9372 PC S5 X Win TELEPROF Software S5 Add on package single license 9372 PC S5 X S Win TELEPROF Software S5 Add on package Subsequent license 9372 PC S5 F X Win TELEPROF Software S5 Add on package company license 4 2 2 2 S7 4 2 2 2 1 Ground package Order number Article description 9372 PC Win TELEPROF Software S7 Ground package single license 9372 PC S Win TELEPROF Software S7 Ground package Subsequent license 9372 PC F Win TELEPROF Software S7 Ground package company license 4 2 2 2 2 Add on packag e Order number Article description 9372 PC X Win TELEPROF Software S7 Add on package single license 9372 PC X S Win TELEPROF Software S7 Add on package Subsequent license 9372 PC F X Win TELEPROF Software S7 Add on package company license 2003 2011 by PI TIS 11 Operating instructions Tele Network 4 2 3 PLC connection cable Order number Article description 9361 3 PLC connection cable 15pins S5 3 m 9361 3 05m PLC connection cable 15pins S5 5 m 9361 3 06m PLC connection cable 15pins S5 6 m 9361 3 10m PLC connection cable 15pins S5 10 m 4 2 4 Accessories 4 2 4 1 Mounting accessories Order number Article description 9391 MT Mounting set for DIN rail holder 4 2 4 2 Other acc
77. alling a channel Menu item TELE SWITCH 1st line TELE SWITCH 2nd line xx to ChaNr yy xx PG or PLC UP DOWN key yy Channel 00 fed through mode finished yy Channel 01 to 16 call corresponding slave number After this input the question Switch YES NO is displayed e YES Input is taken over channel is called e NO Input is dismissed present condition remains If there is a call then it is reported whether the call or the transformation respectively were successful or not After connection clear down the SWITCH is automatically deactivated 2003 2011 by PI TIS 135 8 12 3 Technical data of the TELE SWITCH Supply Voltage 24V DC Power input 12 VA Functional control LED display for the channel calling Working temperature 5 to 55 degree Celsius Dimensions Metal casing 325 x 182 x 42 mm 8 13 Possibillity of Programming of Siemens OPs With the TELE Network devices with a software version bigger than 4 41 it is possible to programm Siemens Ops For this you have to do following 8 13 1 Programming with ProTool lite With this you can programm the OP7 17 directly with ProTool lite You have to connect the programming port of the OP with the PG Port of the PLC TELE On the PG TELE side you connect your PC on the same way as you want to programm the plc After connecting the two modems via telefon line you restart your OP for beginning the transfer after this you change to the menu item Special on
78. amme up to maximally 8 plc controls via one telephone connection Turn the TELE Network device to the operation mode KOR MUX see chapter 6 2 7 PG MUX Mode Only for PLC TELE and S5 8 2 2 Operation with intelligent Bus terminal IBX With the intelligent Bus system IBX terminal up to 30 plcs can be contacted At the individual IBX terminals set the PG number of the respective control via the DIP switch that is located at top The terminals are connected with each other in a bus shaped way via a 4wire RS485 line Please note Use a 2 x 2 x 0 25 cable single shielded The shield has to be connected both ways With your S5 software you contact with both variants the desired AG as usual via the PG BUS Bus path calling Switch the TELE Network device to the operation mode KOR MUX see chapter 6 2 7 PG MUX Mode Only for PLC TELE and S5 112 2003 2011 by PI TIS Operating instructions Tele Network 8 3 Operation of several plcs via the H1 Bus It is no problem to attend a complete H1 network With an additional software option it is possible to configure the PLC TELE in sucha way that a local AG can be connected at the PLC socket of the PLC TELE and that a CP can be connected at the PG socket After the connection set up the programmer decides at the PG TELE whether he she wants to programme at the PLC or at the CP With the Bus calling of his her S5 software he she can reach and programme all the SIMATIC S5 PLCs that
79. an either be done by dialing in to a provider via modem create a phone book entry with the corresponding number and mark by clicking inet or by entering the address of your router as Standardgateway and DNS in the network settings In this case the connection will be established via Ethernet TCP IP and your router Here you have to look out for the firewallsettings The Port UDP 1194 musst be opened If the internet connection is established just click the corresponding entry in of the VPN connection and the connection should establish 2003 2011 by PI TIS 81 7 1 3 3 3 5 After establishing VPN Connection If the VPN connection is successfully established a route with all the IP Addresses which are reachable via Ethernet interface of the server PLC Tele will be created for the client Example PLC IP Address 192 168 1 99 PLC Tele Ethernet IP Address 192 168 1 54 Mask 255 255 255 0 Routermode on OpenVPN Pool 10 111 111 0 Mask 255 255 255 0 PG Tele Ethernet IP Address 192 168 0 54 Routermode on PC 192 168 0 1 Standardgateway 192 168 0 54 If the VPN connection is established you can for example reach or even program the PLC with ping 192 168 1 99 7 1 3 3 3 6 Client PC Side For connection with a PC you need 1 An Open VPN installation on your PC 2 The corresponding configuration file and the appropriate certificate for the TELE PROF II 3 The IP Address of the TELE PROF Ill device in the Internet This can
80. ate you have to configure in your PG TELE too More information to this software you will found under www tpa partner de mpivers htm When using the device as PLC TELE and connecting a serial lt gt mpi converter to the PLC V 24 connector of it the device should know at which baudrate the converter is responsive 6 2 5 2 MPI cable Adr If your buildin mpi profibus port is not used or you want to connect an 2nd bus system the device need a own address like every other client in the system You should proof that you use a address no one other used it Possible Values 0 up to 31 6 2 5 3 Cable HSA When you are using a serial lt gt mpi converter like a MPI PPl cable the device should know the correct HSA So you define it with this menu item So with the TELE PROFessional ll you are able to communicate with 2 bus systems You make the choice which system you want to connect it Possible Values 15 31 63 und 126 2003 2011 by PI TIS 55 Operating instructions Tele Network 6 2 6 S7 Config ONLY for PLC TELE 6 2 6 1 PLC MPI address Here is write down the mpi adress for the plc which you need for following options e Pager Option e Fax Option e SPS Option If you haven t configured an mpi adress the device doesn t know which plc gives him the order to dial to send a fax If you have configured the S7 poll list so this entry is not active 6 2 6 2 Poll list If you have more than one plc s which hav
81. can be driven instead of analogue or digital telefon system with an external modem terminal box or with a handy After you have connected the handy modem to the device you should not configurate only the baud rate of the serial communication you must activate this in the TELE PROFessional ll too So you must activate this in the menu item configuration gt telephone gt ext modem Then restart the device so this option will be active 8 9 1 Connecting a handy to a PG TELE The handy or the modem is connected to the port PLC V24 with the same cable you use for connecting to a PC Therefor this port has the same pinning like a pc you don t need a special adapter for connecting it So with the same cable connected to a PC you are able to test the communication or the configuration The with this test detected parameter should be configured in the menu item configuration gt telephone gt ext modem baud 8 9 2 Connecting a handy to a PLC TELE S5 The handy or the modem is connected to the port PLC V24 with the same cable you use for connecting to a PC Therefor this port has the same pinning like a pc you don t need a special adapter for connecting it So with the same cable connected to a PC you are able to test the communication or the configuration The with this test detected parameter should be configured in the menu item configuration gt telephone gt ext modem baud The S5 plc is connected with a 15pin cable
82. changing the data go to this menu item and after select this item you are on your device no longer the on other Be sure that you switch off the remote configuration after ending of the edit because when you mean you are ready with the configuration and you want to edit your own configuration you overwrite the remote configuration and so ist possible you can t get a connect after this operation Before you start the remote configuration you should have the same firmware in both devices Please note that the called device is a PLC TELE because this is only from PG TELE to PLC TELE possible 2003 2011 by PI TIS 31 Operating instructions Tele Network 5 2 2 6 Menu item First config With this menu item it is possible to configure the most important parameter so that the device is ready for action expressly With the cursor keys UP DOWN you can browse through the menutree With ENTER you can select the corresponding menu item With the cursor keys UP DOWN you can change the setting By pressing ENTER key again the selected value will be receipted and stored 5 2 2 6 1 Menu item LANGUAGE e German menu drive in German e English menu drive in English 5 2 2 6 2 Menu item DEVICE TYPE e PLC S5 TELE The device is next to the plc control and is connected to it e PG TELE The device is next to the programming device and is connected to it e PLC S5 KOR MUX The device is not connected directly to the plc but via a SIEMENS M
83. d Baud With this menu item you can define the speed of the connected mpi profibus Please check this baudrate because so there is no communication possible or your bus system will be stopped Menuitem OnBoard MPI Adr With this menu item you define the address of the TELE PROFessional ll as a bus client This address must be a unused address for the bus If you use the default address 0 be shure that no PG with this address will be in the bus too If you start a connection from the office to the plc the devices uses the address you configured in your programming software If your tele service is ready the device uses the configured address Menuitem MPI OnBoard HSA With this menu item you configure the HSA highest station address of the connected bus Please note that a to big HSA will slow down the speed of communication to the bus So in your software there will be the baudrate for the bus system configured Have you configured the fis baudrate to No so the baudrate from the programming software is be used If you re a beginning to programm a plc it is better for you because so you are able to change the baudrate as you like Have you configured this item to Yes the device uses the configured baudrate of the TELE PROFessional ll and ignors the baudrate from the software Menuitem Fix OnBoard Baud While you have tele service to a plc the PLC Tele is for your software a PC MPI adapter So in this drive
84. de This function will be called routing So you can reach plc or pc they are connected to this network The device can be fastened directly to the switchboard Fixing straps for the Hut and C contact rail are optionally available The operation of these remote maintenance units is only allowed if a supervising person is present who can intervene in the installation at any time Please do not intervene in running programmes without visual communication or control Before installing the TELE LINK Network devices please connect them by all means with earthing PE at the casing or at the screw terminal Please read the user s manual closely before installing the device There is no responsibility taken for damages due to incorrect connection or handling O 2003 2011 by Pl TIS 7 Operating instructions Tele Network 3 System requirements 3 1 Requirements The following requirements are demanded for the system environment of the TELE Network devices e 230V line voltage which supplies the power pack of the plug optional or e 24V DC with at least 360mA load current or e TAE mains socket of the Telekom N coded normally 3pin socket NFN lt gt N Extension device modem fax F Telephone N Extension device or e ISDN connector SO bus Euro ISDN DSS1 or national ISDN 1TR6 3 2 Features e CE e compatible with all SIMATIC S5 PLC s e compatible with SIMATIC S7 300 400 plc connection of PLC TELE by
85. der expect to hear from these guys Their entire reason for existing is to do pro bono legal work for free open source software projects We used to list people who violate the BusyBox license in The Hall of Shame but these days we find it much more effective to hand them over to the lawyers Our enforcement efforts are aimed at bringing people into compliance with the BusyBox license Open source software is under a different license from proprietary software but if you violate that license you re still a software pirate and the law gives the vendor us some big sticks to play with We don t want monetary awards injunctions or to generate bad PR for a company unless that s the only way to get somebody that repeatedly ignores us to comply with the license on our code 170 2003 2011 by PI TIS
86. dress 0 be sure that no PG with this address will be in the bus too If you start a connection from the office to the plc the devices uses the address you configured in your programming software If your tele service is ready the device uses the configured address 5 2 2 6 6 Menu item MPI OnBoard HSA With this menu item you configure the HSA highest station address of the connected bus Please note that a too big HSA will slow down the speed of communication to the bus So in your software there will be the baudrate for the bus system configured Have you configured the fis baudrate to No so the baudrate from the programming software is be used If you re a beginning to programm a plc it is better for you because so you are able to change the baudrate as you like Have you configured this item to Yes the device uses the configured baudrate of the TELE PROFessional ll and ignors the baudrate from the software 5 2 2 6 7 Menu item Fix OnBoard Baud While you have tele service to a plc the PLC Tele is for your software a PC MPI adapter So in this driver you can configure the baudrate of your bus system Have you configured the fix baudrate to No the device gets the baudrate from your software and will use it This is an advantage for you so you can change the baudrate from the office you want and no one must chage the configuration of the plc If you have configured it to Yes the TELE PROFess
87. e order to fax send sms for the tele network device so you can edit this list with the adresses of this plc s This list is be reed for following options e Pager e Fax e SPS ASCII TELE If you edit only a 0 in this list so the device uses only the PLC MPI address entry 56 2003 2011 by PI TIS Operating instructions Tele Network 6 2 7 PG MUX Mode Only for PLC TELE and S5 With this menu item you can use the Multiplexer that is integrated in the TELE Network device For the operation with the Mulitplexer there are the following adjustments e PG MUX Multiplexer between telefone line and the PG Port is active standard When you have a telefone connection there will be possible to communicate to the plc via telephone and directly on the PLC TELE e PG lt gt AG The PG Port of the PLC TELE is connected to the PLC Port the integrated multiplexer is off The data from the PG Port will be transferred directly and without time controll to the PLC Port After a telephone connect this communication will be broken so the communication above telephone line can use maximum speed and performance After hang up the line the PG Port top PLC Port communication will be driven again e PG MUX C The PG Port of the PLC TELE is connected to the PLC Port the integrated multiplexer is off The data from the PG Port will be transferred directly and with time controll to the PLC Port After a telephone connect this communication wil
88. e then you should change the modem type Menuitem Dialmode e Tone The modem dials with the modern MFV system this means you hear while dialing a little melody e Pulse The modem dials with pulses that means you hear while dialing the noise of a relais 50 2003 2011 by PI TIS Operating instructions Tele Network Menuitem Extension mode e YES The device is not connected directly to the line You then need either a prefix number or a certain key combination to get to the line e NO The device is either connected directly to the line i e you do not need a prefix number in order to get a line or the device is within a private branch exchange and should call a partner within this system Menuitem Outline Code With these possible figures you can config the device to get a telefon line 0 1 2 3 4 5 6 7 8 9 1 gt H X W Menuitem Rings before Lifting e 0 With this adjustment the modem does not pick up independently With the menu item pick up you have tomake the modem pick up manually e 1 5 Modem picks up after the adjusted number of rings The operation of these remote maintenance units is only allowed if a supervising person is present who can intervene in the installation at any time Please do not intervene in running programmes without visual communication or control Before installing the TELE LINK Network devices please connect them by all means with earthing PE at the casing or at the screw
89. e user must start the internet connection via phone book manually Therefore create the corresponding entry in the phone book and don t forget the cross in the column inet so the TELE PROF I knows that this is a connection to the internet After the connection is established depending to the settings DynDNS will be executed If the connection is closed e g Modem hang up the connection will stay closed Permanent Select a Provider from the phone book Even here you have to note that the cross in column inet is set The internet connection will be tried to remain That means if the device will be turned on the TELE PROF II will automatically turn on the internet connection Even if you cut off the connection the TELE PROF II will turn it on again However we will implement different alternatives 2003 2011 by PI TIS T7 7 1 3 3 2 Using DynDNS DynDNS config TELE PROF Il F NST e torof2 dynalias cam TpDynDNS 1 MyPass oc DN jata 2 We presuppose that the provider has given us a public IP Addresse Now the question is How can the TELE PROF II after dialing up to the internet be reached For this problem there is a solution in the internet The service provider DynDNS DynDNS Dynamic DomainName Server http www dyndns org offers a service Therefore you have to register at DynDNS Details you can find on the homepage of DynDNS Up to 5 dynamic IP Addresses are free If you need some
90. ed Cards Option 3G CDMA Model GTmax EMEA F Mobik AA IN It is recommended to run the card with an external antenna As network operator we have tested T Mobile and found large flexibility and consultation T Mobile currently offers tariffs for web n walk with a monthly data volume till 5 GB Please note that even this amount can be exceeded From then it will be really expensive 1 Euro per MByte So look out for that O 2003 2011 by Pl TIS 15 7 1 3 3 Installation Before you insert the card configuration data has to be entered in the device UMTS GPRS T Mobile Option Gtmax EMEA vw only UMTS v 99999 ca tmobile Cardtype kind of net only UMTS only GPRS 1 GPRS 2 UMTS 1 UMTS 2 GPRS Please inform yourself which net is available in your region from your provider before implementing In case of doubt use 1 UMTS 2 GPRS But therefore we will offer diagnosis possibilities in future Pin It is important that the Pin Number is entered correctly Otherwise it may happen that the SIM Card will be blocked Unblocking it is only possible with the PUK This method is currently not supported by TELE PROF II which means you ought to put the SIM Card in a handy or a notebook and unlock it No SMS Centre This entry can normally be empty If you provide the card in foreign countries please inform yourself about the corresponding numbers from your provider This number is only necessary for SMS ope
91. ed the pg mux mode for pg mux see chapter 6 2 7 PG MUX Mode Only for PLC TELE and S5 2003 2011 by PI TIS 119 8 7 Communication with a mailbox modem With this option now you can communicate with the tele network device from your pg pc above the telefon line into a mailbox esp the modem You only have to configure your terminal programm in your pg pc with following parameters Baudrate 19200 Baud 8 data bit 1 stop bit no parity Handshakes like following TELE PROFessional ll RTS CTS on V24 Connctor At next you select the subscriber you want to dial but now you need this baudrate like M144 or M96 and so on After the connect you can work with your pc and your terminal programm like the modem is build in in your pc 120 2003 2011 by PI TIS Operating instructions Tele Network 8 8 Communication with an S7 PLC This device which is on the plc side must be configured in the menu item Konfiguration Device Type as PLC S7 300 400 If you use the S7 200 you just have to change the device type as PLC S7 200 9K6 or PLC S7 200 19K2 For the PG TELE you don t have to change anything because the PG TELE recognices the plc type wether its S5 or S7 These schematic is for MPI and also for Profibus communication You only have to note that you will use the correct interface cable for the used baudrates If you are using a S7 200 PLC you should activate in the PG TELE in the menu item Speciall the S7 200 ON
92. ed with the TAPI Interface with MS Outlook for example So you can dial or hang up without using the keyboard of the tele network devices So if you have edited more telefon numbers for example 120 so you don t have the time to pull down until you got your telefon entry number 120 So you can controll this with a comfortable software You need following configuration You connect your PC with the second COM port with a so called Zero Modem cable it s a cable not 1to1 you have twisted pairs so 2 to 3 3 to 2 and so on to the plc V24 port of the tele professional After this you install in your pc a standart modem for this com port Please note following TAPI Controll to TELE Professional Dial mode ton impulse count of rings busy identify you must configure it on the Tele Professional It was testet with Outlook 2000 1 Connection to plc v24 port of Device Baudrate 9600 8 N 1 without Handshake 2 Choose standart analog modem with Win 9x or NT please first install then choose 3 In the telefon number MS Outlook Contacts you can with following symbols configure following functions gt Pin number is following but it is only a numeric pin allowed you can t transfer ascci chars with the TAPI function gt Baudrate is following 12 1200 Baud 24 2400 Baud 48 4800 Baud 96 9600 Baud 144 14400 Baud the maximum of the modem gt Callback with the RRV number max 9 figures F
93. ere is an active telephone connection wether analogue or digital The PLC SPS Data LED signs the user that data will be transferred to or from the connected PLC This LED is only flushing while data will be transferred If there will be transferred data from device to device with modem this Modem Data LED will be flushed If there is any error inside of the device or a error with the communication the Erroe LED is on For further information look at the display If you have connected the device to the ethernet this LED will be ON If you have connected the device to the Ethernet and the LED is OFF you should proof the connection or the cable While you send data with Ethernet the LED will be flushed 44 2003 2011 by PI TIS Operating instructions Tele Network 6 Implementing 6 1 Quick Configuration Quick Entrance After mounting the device into the switchboard or placing on the table at first you have to connect the ground connector on the right side of the device with the ground pin of the switchboard Then you connect of the backside of the device the telefon lead into the correct connector and then connect the power 24V with the green connector on the front side After the device is booting you can read in the display not connected so you can begin with the first configuration In order to configure the TELE Network devices quickly and safely there is a special menu item in the menu tree see chapter 5 2
94. essories Order number Article description 9372 TELE PROFessional ll Starter Kit 9379 1 MPI Profibus connection cable 1m 9391 1 24V DC power supply 625mA Primary 100 240V AC 9372 24 Power connector 3pins big 9371 6 Servicebag Only for Flat Version 4 2 4 3 Phone access ories Order number Article description 9370 8 D USA Phone cable analogue Germany USA 9370 8 ISDN Phone cable ISDN 9370 8 AT 9370 8 BE 9370 8 CH 9370 8 DK 9370 8 FR 9370 8 GB 9370 8 IT 9370 8 NL Special phone cable analogue AT BE CH DK FR GB IT NL 9370 Set Phone connector set 16parts worldwide use 9370 TAE TAE junction box 2003 2011 by PI TIS Operating instructions Tele Network 5 Handling General There are two ways to configure a TELE PROF II 1 Via the integrated Web Interface see chapter 5 1 Web browser 2 Via the implemented Keypad see chapter 5 2 On Site Configuration 5 1 Web browser A prerequisite for configuration via Web browser is a correct IP Address corresponding to your PC and a connection to a hub switch or directly to your PC with a cross over cable A configuration with a PC via the serial interface is not possible Start a Web browser of your choice e g Internet Explorer and type the IP Addresse of your device into the address field The default value of the IP Address for the TELE PROFessional ll is 192 168 1 54 so you
95. example PGs and control units All TELE Network devices have the same hardware structure The complete electronics are integrated in a metal casing The TELE PROFessional Il is available in 2 variations 9372 OEM without PCMCIA slot for UMTS LAN card 9372 OEM H with PCMCIA slot for UMTS LAN card 9372 FLAT flat variant without PCMCIA slot for UMTS LAN card 9372 FLAT H flat variant with PCMCIA slot for UMTS LAN card ROMS 6 2003 2011 by PI TIS Operating instructions Tele Network 2 Description The TELE PROFessional 1l can be connected with the integrated 33K6 V42 BIS HIGH SPEED Modem direct to the telephone connector of your local telephone provider and at every analogue port of your telephone system You can connect this device also to a digital connector ISDN SO port The provided protocol is DSS1 Euro ISDN or 1TR6 national ISDN To connect a plc type the device has the correct plug on board For teleservice a S5 plc you use the additional S5 Kabel for connect the TELE PROFessional direct to the programming port of this plc You can connect also to the 15pin female plug a PG or PC to communicate with the integrated multiplexer Or in the office you can connect direct your PG or PC with the correct interface cable to this port If you want to connect the device to a S7 plc you use the integrated 9pin female plug With this port you are able to make connections to MPI and Profibus with baudrates from 19K
96. f Il is communicating with the PLC This can happen very easily Overwrite the Counterbyte of your PLC regularly with OxFF After the defined cycle time there should be another value then OxFF But rate this time generously because the cycle can shift if there is a communicationproblem with other controllers The high byte is reserved for later extensions Currently it is overwritten with 0 Examle If you use FW 200 then FB201 is the counter and FB200 is set to 0 2003 2011 by PI TIS 127 Projecting the Variables Access rights Level Write Superuser Read View U2 Enter the desired variables which should be shown or processed TELE PROF II PISDNST datatype Station mit CP E40 Boolean SPS 2 MW 30 unsigned int a i Boolean Connection address In the following table you can find the usage of each column Column Usage Name Own notation Connection Assignment of a variable to a PLC connection Address The underlying address in the PLC after following rules Data range Data type Input Output Flag Data block E1 0 11 0 A1 0 Q M10 1 DB1 DBX Bit 1 0 1 0 Boolean EB1 IB1 AB 4 QB 4 FB 20 DB2 DBB BYTE 20 EW 4 IW4 AW 6 QW FW 100 DB4 DBW WORD 6 0 ED4 ID4 AD6 QD6 FD 100 DB4 DBD DWORD 10 Daten range Data type Timer Counter T1 sf wee Timer Z1 C1 Counter Data type Choice of
97. function only for Siemens devices SPS function only for Siemens devices ASCll function only for Siemens devices Bosch CL200 CL300 CL400 CL500 AEG A 120 A 250 Mitsubishi FX Serie A Serie ALLEN Bradly SLC 500 DF1 protocoll DH485 Klockner Moeller PS3 plc PS4 plc V24 156 2003 2011 by PI TIS Selectron PMC 20 GE Fanuc Pilz PSS3xxx Operating instructions Tele Network Telemechanique Premium TSX57 Please note that for each of the mentioned plc types you should ask your dealer if this plc firmware is integrated in this TELE PROFessional ll Sometimes you can use the older one called TELE Professioanl where you can download the special firmware with the Tele Manager Software into the device The connection between Tele PROF Il and Tele Professional is provided 9 6 Used Ports Port Type Description 9998 TCP Firmware Transfer 9999 TCP Remote Maintenance between 2 devices 9999 UDP Remote Maintenance between 2 devices 80 TCP Webbrowser Access 102 TCP CP Mode RFC1006 O 2003 2011 by Pl TIS 157 10 Troubleshooting Display Condition Display remains dark Modem does not dial Return call does not work No connect by dialling Device doesn t lift up Hardly ONLINE to the ple No ONLINE to the plc 158 Cause Voltage connected Voltage poled Telephone line connected Telephoneline in the correct connector
98. g A communication with ISDN is without MSN EAZ is not possible A special part is the system of Siemens called HICOM With a optiset E ISDN adapter you don t need a MSN EAZ number If you have defined one the device doesn t work with this system 6 2 9 12 Analogue on ISDN Here with this menu item it is possibel for TELE PROFessional with a hardware version of 1 1 to communicate with a analogue partner althoug it is connected to a digital ISDN port So with this feature you don t have to aks your customer do they use analog or digital you only have to select it in this menu item you are possible to drive both Possibel Values YES and NO After changing this menu item the TELE PROFessional II must be restartet 62 2003 2011 by PI TIS Operating instructions Tele Network 6 2 9 13 ISDN aLaw uLaw For the connection with analogue on ISDN you should know which protocol is for the digitalization of the analogue system used Following protocols are provides with the TELE PROFessional ll e aLaw europe north america e uLaw south america After changing of this item you must restart the device again 6 2 9 14 ext modem You can drive the TELE PROFessional ll with analogue or digital telephone system you can drive it also with handy or a external modem Therefore you have to connect the handy modem to the PLC V24 port of the Tele PROFessional ll With this item you change the communication path
99. g instructions Tele Network 7 Field of Application 7 1 Remote Maintenance 7 1 1 Via telephone line 7 1 1 1 Description A Remote TELE PROFessional Il which is connected to the PLC will be called from the local TELE PROFessional II Consequently you can access your PLC from your PC via telephone line quick and easily 7 1 1 2 Requirements Hardware 2x TELE PROFessional Il The remote maintenance can be also realized with only one TELE PROFessional II For further information please read chapter 7 1 2 WinTeleProf as replacement for PG TELE after that 7 1 1 3 Create Subscriber The TELE PROFessional Il has a phone book similar to a mobile phone in which you can store up to 197 entries To create a new entry or edit an existing entry choose the menu item Edit subscriber More information to this topic you can find in chapter 5 2 2 4 Menu item Edit subscriber 2003 2011 by PI TIS 67 7 1 1 4 Communication establishment Schematic Serial Interface of your PC erface of PLC TEL MPLProfibus Pre cable Order No 9379 1 E To MPILProfibus l erial Cab To PG V 24 Interface of PG TELE PG TELE PLC TELE 7 1 1 4 1 Configuration PG TELE The Device which is connected to your PC must be configured as PG TELE under Configuration Device type 7 1 1 4 2 Configuration PLC TELE The Device which is connected to the PLC must be configured as PLC TELE depending on which PLC you want to contro
100. gn with transmit time With yes the transmitting time will be inserted to the SMS header important Set the time correctly Insert message time With yes the time at which the message occurred will be inserted into every message Thereby the SMS will be longer but the moment at which the message occurred can be protocolled SMS message buffer Access rights Level Write Superuser Read View U2 On the site sms message buffer you can see the queued messages which have not been sent yet The column tx trying shows the number of tries to send the message This is bigger then 0 when for instance the phone line does not exist is busy or the server settings have not been set correctly The highest number of tries will be reported to the PLC see above SMS message buffer time page receiver 09 03 2005 16 43 Mr Maier 017188299382 provider text tx trying TD 1 SMS 09 03 2005 16 43 UPS power supply O F F 1 09 03 2005 16 43 Mr Maier 017188299382 TD 1 SMS 09 03 2005 16 31 Comm error PLC 2 2 1 2003 2011 by PI TIS 133 By clicking the symbol G every message in the list will be deleted The messages will not be sent For test purpose you can remove the phone cable so you can test the functions of the machine without causing costs for sms sending Show Messages Access rights Level Only reading is U1 possible
101. he TELE Network device every 5 seconds Example FW10 can be divided into FB10 and FB11 FW Flag word 10 FB 10 FB 11 command byte Number of the entry in the subscriber list Reference card for the command byte 01h Start dialling process After the connect with the called station a 10h is written back in this register 02h Hang up the modem This command is only possible if the connected TELE LINK is the caller or if there is no connection by phone at all The TELE LINK then disconnects the existing connection If the command has been executed a 30h will appear in the status register In case of an error a 50h will appear 03h Hang up the modem in any case This instruction is executed in any case immediately and directly A 30h will appear in the same register O 2003 2011 by Pl TIS 89 Return messages of the TELE network device in the command byte 10h Modem connection with TELE LINK plc TELE or PG TELE existing 20h The number of the desired subscriber entry is invalid 30h Modem connection does not exist anymore e g after hanging up or after the partner has hung up 40h A Connect is not possible probably because line is busy 50h The command to hang up 02h could not be executed 60h Modem connection with ASCII subscriber exists 7 2 1 2 Setup of the SPS TELE flag Example FW12 can be divided into FB12 and FB 13 FW 12 FB 12 FB 13 direction of sending transmission status Direction of sending
102. ialling series German European system 1 2 3 4 5 6 7 8 9 0 Scandinavian system 0 1 2 3 4 5 6 7 8 9 For a call from Sweden to the following German number 0049 11833 information service of the Telekom the following number has to be input 1150 22944 For a world wide operation with the TELE Network devices it is normally indispensable to use for each country in which the modem is used the modem corresponding to that country e g for Great Britain a British modem for Spain a Spanish modem and so on Experience shows that this is not always possible Then the decision has to be made by the user himself herself The above table that shows the usable modem types for several countries is put together according to practical experience Therefore it is not guaranteed that the corresponding TELE Network device has the admission for the operation in the country in question Technically speaking the US modem works in every country since it does not have the restrictions a German modem has as for example bell voltage bell frequency charging pulse filter and so on 146 2003 2011 by PI TIS Operating instructions Tele Network 9 4 3 ISDN connector The TELE PROFessional ll should be connected from the ISDN port to the ISDN plug on the wall with a standard ISDN cable But before you can use digital communication you should be shure and check the protocole of your ISDN Possible protocols e DSS1 Euro ISDN e
103. ication protocol specific for controls as for example the AS511 protocol of Siemens plcs After the TELE Network devices have built up a connection the direct transparent mode can be turned on There is now a direct coupling between the PG socket of the PG TELE and the PG socket of the PLC TELE This means that data that enters the PG TELE is released unchecked at the PLC TELE In this way you can transfer files from one PC to another configure a connected OP or simply transfer and execute the protocol of another control which is not supported by the TELE Network devices The direct mode can only be activated from the PG TELE Moreover it is an unprotected transmitting medium without special checking Because of that it is a plain modem route with modem security correction of errors according to modem standards We cannot take any guarantee for run time errors 7 5 1 Source Com With this menu item the device is configured for the so called transparent mode The TELE Network device is adjusted to parameters that are specifically made for transmission e PG or PLC socket connection input from the dialling TELE LINK e Baud rate 300 1200 1800 2400 4800 9600 19200 38400 Baud e Number of data bits 5 to 8 bits e Parity N none E even O odd e Number of stop bits 1 1 5 and 2 bits 106 2003 2011 by PI TIS Operating instructions Tele Network 7 5 2 Dest Com In this menu item the device is configured for
104. icense The Program be low refers to any such program or work and a work based on the Program means either the Program or any derivative work under copyright law that is to say a work containing the Program or a portion of it either verbatim or with modifications and or translated into another language Hereinafter translation is included without limitation in the term modification Each licensee is addressed as you 2003 2011 by PI TIS 159 Activities other than copying distribution and modification are not covered by this License they are out side its scope The act of running the Program is not restricted and the output from the Program is cov ered only if its contents constitute a work based on the Program independent of having been made by running the Program Whether that is true depends on what the Program does 1 You may copy and distribute verbatim copies of the Program s source code as you receive it in any medium provided that you conspicuously and appropriately publish on each copy an appropriate copy right notice and disclaimer of warranty keep intact all the notices that refer to this License and to the absence of any warranty and give any other recipients of the Program a copy of this License along with the Program You may charge a fee for the physical act of transferring a copy and you may at your option offer war ranty protection in exchange for a fee 2 You may modify your copy or copies of the
105. ient must have this address he will be recognized through this number So the TELE PROFessional ll knows that he will be meant and it will take the call Often the number of the telephone plug is also this number Please contact your supervisor of the telephone system to get this information So he can also change the ISDN property to modem this will be needed for this telephone plug A special part is the system of Siemens called HICOM With a optiset E ISDN adapter you don t need a MSN EAZ number If you have defined one the device doesn t work with this system Menuitem Ethernet IP If you want to use the TELE PROFessional ll in your company network you should configure a IP address in this device This IP address is divided into 4 blocks so you have to configure this address like 192 168 1 100 Between these 4 blocks you can change with gt and lt The input will be finished with the ENTER key After RFC1918 free IP addresses 10 0 0 0 10 255 255 255 172 16 0 0 172 31 255 255 192 168 0 0 192 168 255 255 2003 2011 by PI TIS 49 Operating instructions Tele Network Menuitem ISDN IP The communication between each device is a ppp protocoll so every device need a different ip address As you can connect with ISDN or analogue so you need 2 different ip addresses So every PG TELE needs another address like the PLC TELE While you don t need a communication between PLC TELE and other PLC Tele PLC
106. if the connected TELE LINK is the caller or if there is no connection by phone at all The TELE LINK then disconnects the existing connection If the command has been executed a 30h will appear in the status register In case of an error a 50h will appear 03h Hang up the modem in any case This instruction is executed in any case immediately and directly A 30h will appear in the same register Return messages of the TELE network device in the command byte 10h Everything OK fax sent 20h The number of the desired subscriber entry is invalid 30h A data module is too small 40h A Connect is not possible probably because line is busy 50h Error occurred when fax was transmitted O 2003 2011 by Pl TIS 99 7 4 1 2 Set up of a communication data module at the FAX TELE DW 0 DW 9 the station ID of the plc fax is input as KC e g 49 1122331121 Input only valid ASCll signs otherwise blanks up to DW 9 DW10 Source data module 1 DW11 start data word in this DB DW12 number of data words in this DB DW13 source data module 2 DW14 start data word in this DB DW15 number of data words in this DB DW16 etc The end of the list is recognised if the number O zero is input in the source data module Example The characters in DB 5 up from DW 4 100 words and in DB 10 up from DW O 200 words should be sent Set up of the module DWO DW9 KC 4996199999 as you like it DW10 5 DW11 4 DW 12 100 DW 13 1
107. ing up which is explained further down is turned to zero and if the modem does not pick up independently 5 2 2 5 3 Data Mode In case there is only one telephone line that should be used by a TELE Network device and for the telephone communication with your co worker you can use this telephone line with this menu item for both ends The co worker recognises after picking up a parallelly working telephone the signal of a Calling TELE Network device and can then connect the TELE Network to the line with this menu item The device disconnects the existing connection to the telephone takes over the line and is then in data mode with the calling device In case of speech mode this menu item can be used as well in order to connect TELE Network devices to the line In this case however this function has to be carried out at both devices Only hang up the phone after the TELE Network has displayed CONNECT Do not hang up the phone if there should be a speech mode after the data mode Analogue see voice mode 2003 2011 by PI TIS 27 Operating instructions Tele Network 5 2 2 5 4 Voice Mode This is the contrasting command to the command DATA MODE It disconnects an existing data connection and the speech connection is released again Do not hang up the phone while the data mode is in process Analogue see data mode 5 2 2 5 5 Init Modem With this command modified initialisations are transferred to the modem 5
108. ional 1 will use the baudrate of its own configuration The advantage for this is that you can t define a baudrate greater than 1 5 MBaud in the programming software So you are connected to bus systems with baudrates 6 MBaud or 12MBaud and so you can tele service these bus systems The baudrate is fixed 2003 2011 by PI TIS 33 Operating instructions Tele Network 5 2 2 6 8 Menu item MPI Profibus e MPI Bus The connected bus system is a MPI bus e Profi DP Stand The connected bus system is a profibus with the profile DP Standard e Profi DP FMS The connected bus system is a profibus with the profile DP FMS 5 2 2 6 9 Menu item MPI cable Baud The in this menu item configured baudrate is the baudrate the connected PC communicates with the PG TELE The siemens software only provides baudrate up to 38400 so you can use a tool called mpi speed to setup the baudrate up to 115200 Baud This baudrate you have to configure in your PG TELE too 5 2 2 6 10 Menu item ISDN EAZ MSN The so called EAZ MSN is the device number of the TELE PROFessional 1 on this telephone plug For the ISDN SO bus every client must have this address he will be recognized through this number So the TELE PROFessional ll knows that he will be meant and it will take the call Often the number of the telephone plug is also this number Please contact your supervisor of the telephone system to get this information So he can also change the ISDN pro
109. istribute 7 You may place library facilities that are a work based on the Library side by side in a single library together with other library facilities not covered by this License and distribute such a combined library provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted and provided that you do these two things a Accompany the combined library with a copy of the same work based on the Library uncom bined with any other library facilities This must be distributed under the terms of the Sections above b Give prominent notice with the combined library of the fact that part of it is a work based on the Library and explaining where to find the accompanying uncombined form of the same work 8 You may not copy modify sublicense link with or distribute the Library except as expressly provided under this License Any attempt otherwise to copy modify sublicense link with or distribute the Library is void and will automatically terminate your rights under this License However parties who have re ceived copies or rights from you under this License will not have their licenses terminated so long as such parties remain in full compliance 9 You are not required to accept this License since you have not signed it However nothing else grants you permission to modify or distribute the Library or its derivative works These actions are prohib ited by law if yo
110. it until the SPS Toolbox appears SPS Mega Toolbox V1 29 Tele Professional 11 Process Informatik En mbH gt Prof II Manager SPS Toolbox 3 WinTeleProf ees Forum rorum Short Manual German Short Manual English Online Shop Manual German m nu i english Visit our HomePage S7 200 Remote Access with the TELE PF Router German I A 0 Sollte dieser Dialog nicht automatisch erscheinen starten Sie bitte die Datei Mega exe auf der SPS_MEGA_TOOLBOX CD 70 2003 2011 by PI TIS Operating instructions Tele Network 2 Click on Tele Professional II and then select WinTeleProf to install the demo version Select Language Please select the language you want to use EE y Cancel l Select destination folder 3 After choosing language the welcome dialog appears in the chosen language Click Next to define the installation path see At picture This can be done by e ernor i Same clicking Browse If you are ready press Next to continue Click Next to continue with the installation Back to review the last step or Cancel to exit ThunderS etup lt Back Cancel 18 Select program group 4 In the next dialog you can Setup will create shortcuts in the following folder choose the program folder for E WinTELEPROF your start menu Continue with ABC FlowCharter 4 0 S N ext ABC OLE Automation Demos Autostart Canon PhotoRecord Canon
111. item After connecting the both modems together you should do this Now you can work with the programmingtool MicroWin It is better for the communication you configure your device driver PPI Cable with the modemconnection With this feature you get longer timeouts For the modem device you can use the Bausch Induline IL 14K4 with the normal standard parameters The pc is connected to the PG TELE PG V24 port with a straight cable 1Tto1 pin Connection scheme PG COM PG UNI Kabel G or or 9pol 1to1 V24 PG TELE with S7 Software Original cable for S5 of PG 7xx telephone line MPI PPI cable or MPI II for PLC TELE S7 300 and 400 ea PLC V24 PC PPI cable for S7 200 MPI bus direct S7 300 400 CCC buildin MPl port The baudrate of the serial communication is able up to 115200 baud You should only recognize that cables like PG COM PG UNI are not able to drive this baudrate For a communication with TTY there is only maximum 38400 baud possible If you connect direct RS232 then you can drive the 115200 baud If you use Siemens Step7 software you should use the tool MPI Speed for to drive this higher baudrates A connection in the office to the build in MPI port is in the moment not possible You should use the driver PC Adapter with the serial baudrate of 19200 up to 115200 baud 2003 2011 by PI TIS 121 8 9 Communication with external handy or modem The TELE PROFessional ll
112. ive the users of those programs of all benefit from the free status of the libraries themselves This Library General Public License is intended to permit developers of non free programs to use free libraries while preserving your freedom as a user of such programs to change the free libraries that are incorporated in them We have not seen how to achieve this as regards changes in header files but we have achieved it as regards changes in the ac tual functions of the Library The hope is that this will lead to faster development of free libraries 2003 2011 by PI TIS 163 The precise terms and conditions for copying distribution and modification follow Pay close attention to the difference between a work based on the library and a work that uses the library The former con tains code derived from the library while the latter only works together with the library Note that it is possible for a library to be covered by the ordinary General Public License rather than by this special one TERMS AND CONDITIONS FOR COPYING DISTRIBUTION AND MODIFICATION 0 This License Agreement applies to any software library which contains a notice placed by the copy right holder or other authorized party saying it may be distributed under the terms of this Library General Public License also called this License Each licensee is addressed as you A library means a collection of software functions and or data prepared so as to be conveniently
113. l The automatic pick up should also be enabled For this you have to set the value under Configuration Modem Count of Rings to 1 7 1 1 4 3 Connection establishment To establish a connection the number of the PLC TELE has to be stored in the phone book of the PG TELE Select the menu item Select subscrb and then the entry which includes the number of the PLC TELE to cause a phone call 7 1 1 5 Accessing PLC Now you can communicate with the PLC as if it was connected to your PC directly For further information please read chapter 8 8 Communication with an S7 PLC 7 1 2 WinTeleProf as replacement for PG TELE 7 1 2 1 What is WinTeleProf WinTeleProf is a Software which simulates the PG TELE in the remote maintenance via telephone see chapter 7 1 1 Via telephone line Thereby the remote maintenance can be realized with only one TELE PROFessional II Though you will need an additional external 56k Modem and the WinTeleProf Software on your local PC For the remote maintenance the carrier frequency must be constant Some notebook soft modems neglect that because they mainly are designed for surfing the internet where the frequency is given by the provider Our advice is to use an external modem instead 7 1 2 2 Requirements Hardware 1x TELE PROFessional II 1x 56k Modem Extern Software 1x WinTeleProf 7 1 2 3 Installation 1 Insert the SPS_MEGA_TOOLBOX Disc into the CD ROM drive of your PC and wa
114. l be broken so the communication above telephone line can use maximum speed and performance After hang up the line the PG Port top PLC Port communication will be driven again This mode is only for S5 Mode of the Tele Network Device in use 6 2 8 IP Address 6 2 8 1 Ethernet IP If you want to use the TELE PROFessional ll in your company network you should configure a IP address in this device This IP address is divided into 4 blocks so you have to configure this address like 148 149 1 100 Between these 4 blocks you can change with gt and lt The input will be finished with the ENTER key The default IP address of this device is 192 168 1 54 According to RFC1918 free IP addresses 10 0 0 0 10 255 255 255 172 16 0 0 172 31 255 255 192 168 0 0 192 168 255 255 2003 2011 by PI TIS 57 Operating instructions Tele Network 6 2 8 2 mit Eth Netmask Here you can configure if you want to work for the IP communiccation with a subnet mask If you want you should select a correct subnet mask for your system because wrong subnet mask may cause problems in the communication Possible Values Yes and No If you choose NO the Subnetmask will be automatically calculated based on the IP Address Details for the calculation you can find in chapter 7 3 1 IP Address respectively 7 3 2 Netzmask Subnetmask 6 2 8 3 Ethernet Netmask Here is the subnet mask if you want to use it to define Please note that you use a
115. linked with application programs which use some of those functions and data to form executables The Library below refers to any such software library or work which has been distributed under these terms A work based on the Library means either the Library or any derivative work under copyright law that is to say a work containing the Library or a portion of it either verbatim or with modifications and or translated straightforwardly into another language Hereinafter translation is included without limitation in the term modification Source code for a work means the preferred form of the work for making modifications to it For a li brary complete source code means all the source code for all modules it contains plus any associated interface definition files plus the scripts used to control compilation and installation of the library Activities other than copying distribution and modification are not covered by this License they are out side its scope The act of running a program using the Library is not restricted and output from such a program is covered only if its contents constitute a work based on the Library independent of the use of the Library in a tool for writing it Whether that is true depends on what the Library does and what the program that uses the Library does 1 You may copy and distribute verbatim copies of the Library s complete source code as you receive it in any medium provided that you conspicuousl
116. male lt gt male to the PG TTY port of the TELE PROFessional ll This cable is not a 15pin 1to1 cable it has a special pinnnng name and article number The name is CP KABEL and the article number is 9359 90 After you got a telephone connect to this device you don t have to care that the plc is not connect to the plc port this makes the device itself 122 2003 2011 by PI TIS Operating instructions Tele Network 8 9 3 Connecting a handy to a PLC TELE S7 300 400 The handy or the modem is connected to the port PLC V24 with the same cable you use for connecting to a PC Therefor this port has the same pinning like a pc you don t need a special adapter for connecting it So with the same cable connected to a PC you are able to test the communication or the configuration The with this test detected parameter should be configured in the menu item configuration gt telephone 3 ext modem baud The S7 plc is connected here to the build in mpi port Only so is the communication to the plc and a handy communication possible 8 10 Firewall The TELE PROFessional II has an integrated Firewall to block undesirable access from outside This can be switched on or off under Configuration Firewall Via Web Server Netzwork Firewall you can configure further options firewall N erlauben erlauben ti erlauben Y tl erlauben Y erlauben Y tl erlauben Y erlauben erlauben Y erlauben et e
117. me after which the message is sent out when the limit is exceeded in seconds So a measured value can be debounced If The requirement comparative operation to realize a limit transgression or a report condition Possible comparisions gt lt lt gt means no limit observation only displaying G0 G9 The assignement to each report group So the particular message is assigned to a group of recipients 2003 2011 by PI TIS 131 Context Connections Variables Normings report groups Messages PLC 1 PLC 2 PLC n MPI or TCP IP MPI or TCP IP MPI or TCP IP MPI Address IP Address Messagegroups GO G9 An SMS Message is materialized like following Messages Report groups GO G9 Pagerreceiver PagerProvider SMS Messages 132 2003 2011 by PI TIS Basical HMI Settings Access rights Level Write Superuser Read View U1 TELE PROF It PLISDN Operating instructions Tele Network To activate a report processing basical settings have to be done Before activating these settings the messages should be projected The meaning of each row Row Usage activate SMS server Yes No name of plant This text will be sent to the recipient in the SMS header so that he can identify the sender SMS sender for UCP At the UCP Protokoll the phone number of the sender has to be sent to the SMS Server Si
118. methods e Tone The modem dials with the multi frequency dialling method most common method for telephone installations in the public telephone network only used with digital exchanges e Pulse The modem dials with the pulse method sometimes this is still used in older telephone installations most common method in the public telephone network in Germany 60 2003 2011 by PI TIS Operating instructions Tele Network 6 2 9 6 Extension There are only two possible adjustments e YES The device is not connected directly to the line You then need either a prefix number or a certain key combination to get to the line e NO The device is either connected directly to the line i e you do not need prefix number in order to get a line or the device is within a private branch exchange and should call a partner within this system 6 2 9 7 Speaker So if you have very often connections to a other TELE PROFessional ll it is possible to switch the speaker off If you have select this item you will don t hear anything from the speaker until you switch the menu item back 6 2 9 8 Hangup hearing With this menu item you adjust whether you want to hear how the modem hangs up If so you can also determine a time span in seconds e O second You cannot hear how the modem hangs up e 1to10 seconds You can hear the modem hanging up for the duration of 1 to 10 seconds 6 2 9 9 Baud rate manual This entry of the Baud rate is
119. mitation as if written in the body of this License 13 The Free Software Foundation may publish revised and or new versions of the Library General Pub lic License from time to time Such new versions will be similar in spirit to the present version but may differ in detail to address new problems or concerns Each version is given a distinguishing version number If the Library specifies a version number of this License which applies to it and any later version you have the option of following the terms and condi tions either of that version or of any later version published by the Free Software Foundation If the Li brary does not specify a license version number you may choose any version ever published by the Free Software Foundation 14 If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these write to the author to ask for permission For software which is copyrighted by the Free Software Foundation write to the Free Software Foundation we sometimes make excep tions for this Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally NO WARRANTY 15 BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE THERE IS NO WARRANTY FOR THE LIBRARY TO THE EXTENT PERMITTED BY APPLICABLE LAW EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND OR OTHER PA
120. n key again to select your next adjustment Press ENTER to save it Menu item LANGUAGE e German menu drive in German e English menu drive in English Menu item DEVICE TYPE e PLC S5 TELE The device is next to the plc control and is connected to it e PG TELE The device is next to the programming device and is connected to it e PLC S5 KOR MUX The device is not connected directly to the plc but via a SIEMENS Multiplexer PG BUS dialling via a coordinator e g 923 C or via the IBX Bus Bus system of PI with PG BUS dialling special type of PLC TELE The built in Multiplexer is not active in this operation mode e PLC S7 300 400 This device is connected to a S7 300 400 plc e PLC S7 200 9K6 This device is connected to a S7 200 plc and communicates with 9600 Baud on port PLC V24 e PLC S7 200 19K2 This device is connected to a S7 200 plc and communicates with 19200 baud on port PLC V24 e PLC S5 F Type This device is connected to S5 plc especially a F Type e PLC PILZ This device is connected to PILZ PSSxxx plc you should connect the plc with its own programming cable e PLC Allen Bradley This device is connected to a Allen Bradley SLC5 plc and communicates with the DH485 or DF 1 mode Menuitem MPI OnBoard Y N e Yes The build in mpi profibus connector is activated and be used e No The build in mpi profibus connector is deactivated 2003 2011 by PI TIS 47 Operating instructions Tele Network Menuitem MPI OnBoar
121. n progress you can t press any key and the device does not the action you want This is of secure purpose 18 2003 2011 by PI TIS Operating instructions Tele Network 5 2 2 Menutree Changeable via Keypad Changeable via Web Browser messages hang up e select subscrb 8 Selection of one of the possible 197 subscriber entries and the dial to edit subscriber e The edit of the 197 subscriber Number of the entry Name max 9 char Baudrate 12 33K R12 R33K M12 M33K ISDN RSDN e Number of the subscriber 16 chars with gt possible the next 16 chars append to this entry RRV number only with recall intern telefon number of the device that want this recall Connect to IP ONLY for PG TELE 8 E Here you can make a connection to a in the IP addressbook defined name with Ethernet i IP addressbook a E Here is like in a telephonebook the name and the ip address for this name stored You can edit delete and store Onlineaction Hang up O Lift Data mode E Voice mode E Init modem a Login remote ONLY for PG TELE amp Send Firmware a Fetch Firmware a Send OS 65 Fetch OS amp Remoteconfig on ONLY for PG TELE amp Remoteconfig off ONLY for PLC TELE s First Config amp Language Device Type Telephone Configuration Device type 2 PLC S5 TELE PG TELE PLC S5 KOR MUX PLC S7 300 400 PLC S7 200 9K6 PLC S7 200 19K2 PLC S5 F TYPE PLC Pilz PLC Allen Brad
122. name phone no baudrate inet ae pa catback Eataa head no user Rct B WAx analog PIPE no name phone no baudrate 6 Click on the phone ra number and enter the MIA 1 AG TELE a MAX analog login data you have configured in the menu item Access Codes Check if you have chosen the correct modem and click Verbinden Connect to cause a phone call Verbinde mit TeleProf Il Benutzer Kennwort Modem Connect Status 2003 2011 by PI TIS m m Ls Trennen Telefonnummer f2 Sitecom External 92 Internet Modem DC 014 Abbrechen 73 74 7 If the connection establishment was successful the mainscreen will appear again If you have configured a PIN for the local PLC in your Tele Professional Il under Access Codes then click on RemoteSPS Login enter the PIN and Datei Ansicht verbinde ber Modem Renetelonto RETE enstchinoen E DASR wntelermor Win TELE PROF System state PG TELE PG TELE cancel connection cancel connection Login Login Remote SPS PIN Remote SPS 123456784 Abbrechen 8 If this Message appears you have MEA logged in to your PLC successfully jl Remote SPS Login erfolgreich 2003 2011 by PI TIS Operating instructions Tele Network 7 1 3 Operation with UMTS GPRS Internet OpenVPN 7 1 3 1 Requirements Operating System minimum OS 0 37 Firmware minimum 7 34 7 1 3 2 Support
123. nditions are imposed on you whether by court order agreement or oth erwise that contradict the conditions of this License they do not excuse you from the conditions of this License If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations then as a consequence you may not distribute the Program at all For example if a patent license would not permit royalty free redistribution of the Program by all those who receive copies directly or indirectly through you then the only way you could satisfy both it and this Li cense would be to refrain entirely from distribution of the Program If any portion of this section is held invalid or unenforceable under any particular circumstance the bal ance of the section is intended to apply and the section as a whole is intended to apply in other circum stances It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system it is up to the author donor to decide if he or she is willing to distrib ute software through any other system and a licensee can
124. nds Example FW10 can be divided into FB10 and FB11 FW 10 FB 10 FB 11 command byte Number of the entry in the subscriber list Reference card for the command byte 01h Start dialling process After the connect with the opposite position a 10h is written back in this register When calling a ASCII TELE LINK you receive a 60h at the latest 20 seconds after both modems have built up a connection Another possibility is that the called ASCll subscriber already has a line that he wants to send to the plc before those 20 seconds are over If the plc wants to send immediately you have to call with 04h 02h Hang up the modem This command is only possible if the connected TELE LINK is the caller or if there is no connection by phone at all The TELE LINK then disconnects the existing connection If the command has been executed a 30h will appear in the commando register In case of an error a 50h will be appear 03h Hang up the modem in any case This instruction is executed in any case immediately and directly A 30h will appear in the same register 04h 04h An ASCll subscriber is called If there is a connect afterwards then a 60h is sent to the plc for the connect with the ASCll subscriber Advantage The plc can set down the ASCIl commands immediately after the connect 2003 2011 by PI TIS 115 If there is a TELE LINK PLC or PG at the other end those cannot communicate with each other Only use this if you are sure
125. nector via null modem cable before changing the settings When the settings are stored in the Tele Prof Il all accesses to the modem will be transferred to the external modem If the modem is not connected the device will stop with error messages In this case mostly only a switch off can help Then connect the modem and restart the device Then the external modem has to be deactivated and the new configuration has to be stored ATTENTION In the calling device PG TELE for this the entry no MNP must be activated via Web Browser A connection with a TELE PROF I or Tele Link as PG TELE is not possible in this case A connection establishment from this GSM Device to a TELE PROF I or Tele Link is also not possible Tele Prof Il is possible but at the first connection establishment you have to call twice so the device can switch to no MNP mode 88 2003 2011 by PI TIS Operating instructions Tele Network 7 2 PLC Coupling 7 2 1 Coupling of several pics via the telephone line With the function SPS TELE texts modes data modules etc that have already been stored in the plc can be transmitted from the plc to another plc or they can be fetched from the plc if needed 7 2 1 1 Set up a communication word between the plc and the TELE Network device With each option that demands a common communication flag word between plc and TELE Network device the flag word is set up according to the following scheme and is read by t
126. nges in ist facilities equipment operations or procedures that could affect the proper functioning of your equipment If they do you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service If you experience trouble with this telephone equipment please contact your dealer of this tele network device the telephone number is known by yourself for information on obtaining service or repairs The telephone company may ask that you disconnect this equipment from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning This equipment may not be used on coin service provided by the telephone company Connection to party lines is subject to state tariffs 2003 2011 by PI TIS 141 9 4 Pin assignment of the Tele Proffesional ll 9 4 1 General On top of the device there is a keypad with 6 keys and 2 LED for the communication to the person in front of it TELE Professional lI keypad LAN connector 10 100 MBit LED for status analogue modem Analog Modem double USB Port for future connections MPI Profibus connector up to 12 MBd MPHP I Preowbdus 9 6kBit 12MBit PG V24 connector for ISDN connector direct PC connection DSS1 or 1TR6 double PCMCIA for future connections PLC V24 connector pinning like a PC AG PLC V 24 PG TTY connector for direct PG connection pinning like a S5 plc Ya 1 e a AGI
127. nnect LED goes on With the menu item hang up you can cut the connection 2003 2011 by PI TIS 97 7 3 4 3 How to define hostname DNS and gateway In the menu item configuration net config you can define the hostname for the TELE PROFessional ll You can also define up to 3 DNS server addresses These server will be needed when you use instead of ip addresses names and this names ar not written doen in the own hostlist Example for the host list PG TELE 192 168 1 51 So you write down in the IP address book instead of the ip address the name PG TELE So the device looks in its own list or in the defined DNS server list which ip address is the correct for PG TELE and begin to dial So is you use the DNS Server you can edit central in your company a list with all ip adresses and the name and every client can read and wortk with it If you have no a change you only have to change this list and not every client in your network area And es foreign person don t know what to to with this names For this feature you need the OS 0 10 in your TELE PROFessional ll Standard Gateway This is the IP address in the network system where the device can send to TCP IP packages itself can t send it because the ip address is not in this system So the gateway is a interface that can send the data to other not in this system placed clients Example Operation with a router Tele Prof ll from PC gt Ethernet gt Route
128. nnnn cnn 92 TES AOGE RO D A A E iio 93 2003 2011 by PI TIS 3 Operating instructions Tele Network EES E AIP GGTOCSS Site lira EEEE OAE E TS 94 i322 Neizmask SUDNCINASK lt A A eee ees 95 PIS IDR Gato Way coreene anton Renee tone Na toe e 96 7 3 4 PPP connect for the router FUNCTION ooooccoocccocncconccocnononononanonnnonnnnannnonns 96 7 3 4 1 Connection to a dialing protected TELE PROFessional ll oo eecseeeeseeeeeeneeeeeeneeeeeenaeeeeseeees 96 7 3 4 2 Edit of the modem user with keypad and disSplay oooononccnnnnninnnoccccnnnonnnnnonannnn nono ccnnno nr rr nnnr rca 97 7 3 4 3 How to define hostname DNS and gateway ooococcccconoccconococcnononcncnanonnnc nono cnn nan ncnnnnn rra rn 98 7 4 SEND FAILURE SIGNALS nto ii a ide 99 O eis RE EEE OAL 99 7 4 1 1 Set up of a communication word between plc and TELE Network deViCe ee eeeeeeseeeeeeeneeees 99 7 4 1 2 Set up of a communication data module at the FAX TELE coccccncninnnonononinoninoneninininininininininos 100 7 4 1 3 Sending a fax with the FAX TELE fUnCtion 0 eee ceeeceeeenneee cesses eeneeeeeeaaeeeeeeeaeeeenneeeenenaeeeeeeaees 101 A A 101 7 4 2 1 Messages of the plc sending to a pager c ooooccccccoconocococcnccoconononononccnnnnn nn nn nnnnnnnnnn nn nn cn nn nn anar nenesa nenna 101 7 5 SERIAL EXTENSION DIRECT MODE ceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 106 EEN A taddeu tad cauddadacceddad waeidecudecltae secdtaeedeact
129. not impose that choice This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License 8 If the distribution and or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries so that distribution is permitted only in or among countries not thus excluded In such case this License incorporates the limitation as if written in the body of this License 9 The Free Software Foundation may publish revised and or new versions of the General Public License from time to time Such new versions will be similar in spirit to the present version but may differ in detail to address new problems or concerns Each version is given a distinguishing version number If the Program specifies a version number of this License which applies to it and any later version you have the option of following the terms and condi tions either of that version or of any later version published by the Free Software Foundation If the Pro gram does not specify a version number of this License you may choose any version ever published by the Free Software Foundation 10 If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different write to the author to ask for permission For sof
130. ode 2003 2011 by PI TIS Operating instructions Tele Network 6 2 2 Device name If you input the a device name as for example the installation name number or place the usage of several TELE Network devices and their management is made easier The device name can be asked for with the option remote name and it can be shown on the display By pressing the UP DOWN keys numbers and letters can be edited and the position of the cursor can be changed by using the LEFT RIGHT key Press ENTER in order to finish and save the input of the device name max 9 chars 6 2 3 Router Mode If you activate this menu item you cannuse the TELE PROFessional ll as a router for our network In both devices this option must be activated The IP address of the PG Tele is the gateway address of the connected PC the IP address of the PLC TELE the gateway address of all clients on this network The IP address of the office side must be not the same range of the plc side IP office side 192 168 004 xxx IP plc side 192 168 001 xxx 6 2 4 MPI OnBoard 6 2 4 1 MPI OnBoard Y N Here you can activate the build in MPI Profibus connector In the following items you can configure this connector 6 2 4 2 MPI OnBoard Baud With this menu item you can define the speed of the connected mpi profibus Please check this baudrate because so there is no communication possible or your bus system will be stopped 6 2 4 3 OnBoard MPI Adr With
131. ode to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or c Accompany it with the information you received as to the offer to distribute corresponding source code This alternative is allowed only for noncommercial distribution and only if you re ceived the program in object code or executable form with such an offer in accord with Subsec tion b above The source code for a work means the preferred form of the work for making modifications to it For an executable work complete source code means all the source code for all modules it contains plus any associated interface definition files plus the scripts used to control compilation and installation of the executable However as a special exception the source code distributed need not include anything that is normally distributed in either source or binary form with the major components compiler kernel and 160 2003 2011 by PI TIS Operating instructions Tele Network so on of the operating system on which the executable runs unless that component itself accompanies the executable If distribution of executable or object code is made by offering access to copy from a designated place then offering equivalent access to copy the source code from the same place counts as distribution of the source code even though third parties are not compelled to copy the source along with the object code 4 You may not copy
132. ommunicate with another PC from your PC via a Tele Prof ll connection Therefore it is important that the IP Address families differ from each other That means if you have the address family 192 168 1 xxx in the office the same family should not exist on site A communication in RouterMode is not possible if the same family exists on both sides If possible the IP Addressfamily of the Analoque and ISDN IP Address should not be changed An assimilation of the addresses could cause communication problems which partially only occure sporadically The Router Mode has to be active on both sides Office Machine Side PC IP Address 192 168 1 11 PC IP Address 192 168 2 10 PC Subnetmask 255 255 255 0 PC Subnetmask 255 255 255 0 Standardgateway 192 168 1 54 Standardgateway 192 168 2 12 since Firmware V6 74 with Operatingsystem OS V0 11 no Standardgateway has to be entered This function is works automatically Tele Prof Il Configuration Office Side Configuration Office Side PG TH Office Side IP Addresses Machine Side 192 168 1 54 255 255 255 0 172 16 0 128 172 16 0 129 2003 2011 by PI TIS 93 Tele Prof Configuration Machine Side Configuration Office Side AG S7 300 400 Lz ve y IP Addresses PLC Side 192 168 2 12 255 255 255 0 172 16 0 130 172 16 0 131 If you use a configuration like described the communication from LAN to LAN should w
133. on choose the corresponding config file and press Connect The rest should happen automatically If there is only one config file so directly click connect If there is any problem please look at the Log File There you can find information about what didn t work OpenVPN installs the so called TAP network adapter in windows That is a virtual network adapter This adapter will receive an IP Address from the IP Pool which was configured in the TELE PROF II OpenVPN Server If the Routermode is activated in the TELE PROF ll device the corresponding route to the Ethernet IP network of the TELE PROF II will be set for you automatically Example IP Pool 10 111 111 0 IP Pool Mask 255 255 255 0 Ethernet IP of the TELE PROF II 192 168 100 1 Ethernet IP Mask 255 255 255 0 IP Address of your PC 192 168 1 1 Assigned Address of your TAP Adapter 10 111 111 16 After the connection is established all IP Packets which are sent to the networks 10 111 111 0 and 192 168 100 0 will be routed over the IP Address 10 111 111 16 of your TAP Adapter After disconnecting this route will be removed automatically 7 1 3 3 5 Operation of WinTELEPROF via VPN Please proceed like this 1 Start VPN connection 2 create an entry in the IP Address book with the first IP Address of the IP Pool of the Destination TELE PROF I e g 10 111 111 1 or the Ethernet IP Address of the Destination TELE PROF II e g 192 168 100 1 and connect 7 1 3 3 6 C
134. onfiguration of the Remote Device 1 Start VPN connection 2 Start WEB Browser with the first IP Address of the IP Pool of the Destination TELE PROF II e g 10 111 111 1 or with the Ethernet IP Address of the Destination TELE PROF II e g 192 168 100 1 84 2003 2011 by PI TIS Operating instructions Tele Network What to do if no public IP Address is present Some UMTS GPRS Providers do not assign a public IP Address to the UMTS Cards In this case DynDNS can not be used However for this problem there is a solution You can your modem under http www mdex de Details you can find on the homepage of Mdex From Mdex you will get an OpenVPN Access too If you don t want to perform routing on the TELE PROF II on the machine side you can also connect to the IP Addresses which are given by Mdex In this case you can decline OpenVPN on TELE PROF II But if you want a safe connection you should use VPN here too If you want to perform routing OpenVPN has to be active in the TELE PROF II on site Furthermore you will have to configure another TAP adapter You can find the tool which is necessary therefore in the OVPN directory After connecting to Mdex start another OVPN connection to the TELE PROF II over the IP Address given by Mdex 7 1 3 3 7 Tip for installation 1 Configure the TeleProf and run in the local network 2 Install OpenVPN on your PC and enter the local IP Address of your TELE PROF II as remote address 3
135. ons when you distribute them as sepa rate works But when you distribute the same sections as part of a whole which is a work based on the Program the distribution of the whole must be on the terms of this License whose permissions for other licensees extend to the entire whole and thus to each and every part regardless of who wrote it Thus it is not the intent of this section to claim rights or contest your rights to work written entirely by you rather the intent is to exercise the right to control the distribution of derivative or collective works based on the Program In addition mere aggregation of another work not based on the Program with the Program or with a work based on the Program on a volume of a storage or distribution medium does not bring the other work under the scope of this License 3 You may copy and distribute the Program or a work based on it under Section 2 in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the follow ing a Accompany it with the complete corresponding machine readable source code which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for soft ware interchange or b Accompany it with a written offer valid for at least three years to give any third party for a charge no more than your cost of physically performing source distribution a complete machine readable copy of the corresponding source c
136. or a Username and Password at the next access Please note your Username and Password The full name is just for information For login you will need the Username and Password When logged in as Superuser you have the rights to change every setting Furthermore there are userrights U1 U5 whereas U1 has more rights than U5 Each higher level automatically includes the rights of the lower level that means U1 includes U2 U5 U2 includes U3 U5 etc however with further developement there will be differences for each group If no User with SU rights exists an unchecked access is possible Currently the groups differ from each other like following SuperUser Can watch and edit everything U1 Read only Can not edit anything Connect and Disconnect No access on Userdata WEB user and modem users U2 Read only U3 U5 Not in use Lost login data If you lost your login data it is possible to delete the WEB user via Keypad and display on site at the device Therefore call the menu Configration Access codes delete WEB user and answer all the questions with yes Now all WEB users are deleted and an unchecked access is possible again 2003 2011 by PI TIS 15 Operating instructions Tele Network Login Logout As already mentioned we use the login mechanism of your browser A similar dialog should appear at which you have to enter your login data Verbindung zu 19
137. or example Dial the number 00418762112 with PIN 45671 baudrate 4800 and call back from swiss to germany The right entry is 00418762112 45671 48 0049 The placement of PIN call back option or baudrate don t care it is only iportant that the telefon number is at first O 2003 2011 by Pl TIS 137 More commands for the TAPI function After you get the connect via telephone line you have more commands for the TAPI function via the PLC V24 port All commands beginn with AT You must define every command allone you can t send 2 commands in one command line Every command must be closed with a CR command function AT A Connects the PG TELE to the PLC port of a PLC TELE result OK All is OK ERROR Nothing is OK there must be a failure You must login Function can be activated the other device has a activated pin and there was no login yet command function AT B Connects the PG TELE to the PG port of a PLC TELE result OK All is OK ERROR Nothing is OK there must be a failure You must login Function can be activated the other device has a activated pin and there was no login yet command function AT Dx Tele switch function over the PG Port of the other device X is for the portnumber you want to connect possible values are 1 16 result OK All is OK ERROR Nothing is OK there must be a failure You must login Function can be activated
138. ork properly after connection establishment If you want to use the Tele Prof Il as Router some basic knowledge about IP Addresses Subnetmask and Gateway is required Therefore a short description in the following 7 3 1 IP Address A typical IP Address in decimal notation looks like following 149 174 211 6 four numbers devided by dots The dots have the task to communicate with superior and inferior networks Just like a country identification number local network identification number participant telephone number and sometimes an extension belongs to a phone number in the worldwide telephone network there is an area code the network number and an extension the host number in the internet as well The first part of an IP Address is the network number and the second part is the host number The border between network and host number is defined by a classification scheme for network types The following table makes this scheme a little clear In the columns for the IP Address and the typical example the network number area code part is marked fat The rest of the IP Address is the host number of a PC within this network Networktype Scheme Typical IP Address Class A Network xxx xxx xxx xxx 103 234 123 87 Class B Network xxx xxx xxx xxx 151 170 102 15 Class C Network xxx xxx xxx xxx 192 23 155 113 The highest hierarchy level are the so called Class A Networks Only the first number of an IP Address is the network number the
139. out modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the above copyright notice this list of conditions and the following disclaimer 2 Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution 3 All advertising materials mentioning features or use of this software must display the following ac knowledgment This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http www openssl org 4 The names OpenSSL Toolkit and OpenSSL Project must not be used to endorse or promote prod ucts derived from this software without prior written permission For written permission please contact openssl core openssl org 5 Products derived from this software may not be called OpenSSL nor may OpenSSL appear in their names without prior written permission of the OpenSSL Project 6 Redistributions of any form whatsoever must retain the following acknowledgment This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http www openssl org 168 2003 2011 by PI TIS Operating instructions Tele Network THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT AS IS AND ANY EXPRESSED OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED
140. patible with Siemens MUX LOU A dase EE E E E E A A EEE E 135 8 12 2 Function as 1 ELE S WITH 135 8 12 3 Technical data of the TELE SWITCH cccccseecceneececneceecneesenneesenes 136 8 13 POSSIBILLITY OF PROGRAMMING OF SIEMENS OPS ccc0escceceeeeeeeeeeeeeeeeeaes 136 8 13 1 Programming with ProTool MS cito AA aii 136 8 13 2 Programming with ProTool iii A A AA wae 136 8 14 CONTROLLING OF THE TELE NETWORK DEVICES WITH TAPI INTERFACE 137 9 TECHNICAL DATA OF THE TELE PROFESSIONAL ll cccceesseeeeeeeneees 140 OFT IMIECHANICAL DATA iaa A A A ARA RA AA A Ba oe 140 9 2 ELECTRICAL DATA a eo tes de do es da le 140 9 3 US FCC RULES FOR DEVICES WITH US MODEM occcoocccccnccnccncnnccnnnnconnnncononcnonnnnnos 141 9 4 PIN ASSIGNMENT OF THE TELE PROFFESIONAL ll ooocccocccccocccccocccccoccncconnncconnnnnns 142 FARGO ta tad 142 9 4 2 Analogue ModeM CONNEC OF cooooccccccccccccooconononononnnonononnnnnnncnnnnnnnnnnnnnannnnnnos 143 9 4 2 1 Assignment of the connection pins of the TAE SOCKET occccccinociconoconcnononcnnnnnancnn non ncnnnnnnnnnnn nos 143 9 4 3 ISDIN CGONMEGION ir 147 QA LANACONROCION oe osc ccs did 148 945 USB connector ron aa ee eo eh es 148 9 4 GPCMCIA CONE COR arra A A A A A ae are LLE 149 OAT PG CONMECHON irena a a ae ledocedutedaialedocetetededutuiese 150 9 4 7 1 Pin assignment for the PG socket TTY ceceeceececeeeeeeeeeaeeeeeeeeeeaaeceeeeeseseneaeeeeeeesesecsaeaeeeeeess 151 9 4 7 2 PIN
141. peration With this menu item you can turn the FAX TELE operation on or off 5 2 2 8 3 2 FAX TELE flag With this menu item you can input the common flag word for the data communication Use even numbers only e g FW 122 Only 0 to 254 5 2 2 8 3 3 FAX TELE COM DB With this menu item you can set the communication data base DB in order to set parameter values to the data flow and source at the PLC TELE operation DB 1 to 255 DW 0 to 998 5 2 2 8 3 4 Resolution With this menu item you can select the resolution of the fax transmit Possible parameters are e heavy e fine 2 2 8 3 5 FAX POLL DB In this menu item you define the communication DB for polling It has the same building like the FAX KOM DB But it is only activ when the TELE LINK Network device gets a fax call with a blank paper So you call the TELE LINK Network device with your fax send him a blank page and the device will call back your transmitted fax number with the data configured in the FAX POLL DB DB 1 to 255 DW 0 to 998 40 2003 2011 by PI TIS Operating instructions Tele Network 5 2 2 9 Menu item Special 5 2 2 9 1 To PG PLC interface In this menu item it is decided at the PG TELE whether the communication at the PLC TELE is made via the PLC or via the PG socket Normally the PG TELE communicates with the plc via the PLC TELE and the PLC socket If there is for example a 2nd plc connected to the PLC TELE at the PG
142. perty to modem this will be needed for this telephone plug A special part is the system of Siemens called HICOM With a optiset E ISDN adapter you don t need a MSN EAZ number If you have defined one the device doesn t work with this system 5 2 2 6 11 Menu item Ethernet IP If you want to use the TELE PROFessional ll in your company network you should configure a IP address in this device This IP address is divided into 4 blocks so you have to configure this address like 192 168 1 100 Between these 4 blocks you can change with and lt The input will be finished with the ENTER key After RFC1918 free IP addresses 10 0 0 0 10 255 255 255 172 16 0 0 172 31 255 255 192 168 0 0 192 168 255 255 34 2003 2011 by PI TIS Operating instructions Tele Network 5 2 2 6 12 Menu item ISDN IP The communication between each device is a ppp protocoll so every device need a different ip address As you can connect with ISDN or analogue so you need 2 different ip addresses So every PG TELE needs another address like the PLC TELE While you don t need a communication between PLC TELE and other PLC Tele PLC TELE option the addresses can be the same Please configure this address like 176 16 1 1 This address is also divided in 4 blocks Between these 4 blocks you can change with gt and lt The input will be finished with the ENTER key Please change only this IP address for your PG TELE because all other
143. r gt Internet with VPN gt Router gt Tele Prof 1 To PLC So the IP address of the router is defined inside the TELE PROFessional ll as the gateway address This entry can be written down like the normal ip addresses or with a dns name for example Router1 Host list This list is the list where you write down a dns name and the correct ip address So you want to connect to the dns name PG TELE this device looks at first in its own host list and then if there is no correct entry it looks at the defined DNS server So this host list is a own private DNS 98 2003 2011 by PI TIS Operating instructions Tele Network 7 4 Send failure signals 7 4 1 FAX With the special option FAX TELE texts modes data modules that have already been stored in the plc can be transmitted to a fax if needed 7 4 1 1 Set up of a communication word between plc and TELE Network device With each option that demands a common communication flag word between plc and TELE Network device the flag word is set up according to the following scheme and is read by the TELE Network device every 5 seconds Example FW10 can be divided into FB10 and FB11 FW Flag word 10 FB 10 FB 11 command byte Number of the entry in the subscriber list Reference card for the command byte 01h Start dialling process After the connect with the called station a 10h is written back in this register 02h Hang up the modem This command is only possible
144. r choice ISDN or Analog The entry user is for purpose of sending e mail or for SMS Provider which offer an Internet or PPP access Here a few important Providers Provider Number Protocol T D1 0171 2521001 TAP D2 Vodaphone 0172 2278025 UCP E Plus SMS 0177 1167 TAP 2003 2011 by PI TIS 125 Entering the Pagerrecipients Access rights Level Write Superuser Read View U2 In the next step enter the recipients of the short messages Usually these are handy numbers of the recipients TELE PROF I PLISDNST age receiver Phds ISDN no name NS provider 1 Mr Maier 017188299382 TD 1SMS ere 2 Mr Mustermann 0172111 222 333 D2 SMS 3 The name is freely selectable again Phone number is the handy number of the recipient Inthe column provider you can assign a provider to the recipient The columns GO G9 stand for report groups There are total 10 report groups Each recipient can belong to several report groups Below you can assign several report groups for each group similar like here So you can spread one message to the relevant recipients without any problem 126 2003 2011 by PI TIS Operating instructions Tele Network How do the messages come from the PLC to the handy For the PLC access connection
145. r you can configure the baudrate of your bus system Have you configured the fix baudrate to No the device gets the baudrate from your software and will use it This is an advantage for you so you can change the baudrate from the office you want and no one must chage the configuration of the plc If you have configured it to Yes the TELE PROFessional II will use the baudrate of its own configuration The advantage for this is that you can t define a baudrate greater than 1 5 MBaud in the programming software So you are connected to bus systems with baudrates 6 MBaud or 12MBaud and so you can tele service this bus systems The baudrate is fixed 48 2003 2011 by PI TIS Operating instructions Tele Network Menuitem MPI Profibus e MPI Bus The connected bus system is a MPI bus e Profi DP Stand The connected bus system is a profibus with the profil DP Standard e Profi DP FMS The connected bus system is a profibus with the profil DP FMS Menuitem MPI Kabel Baud The in this menu item configured baudrate is the baudrate the connected PC communicates with the PG TELE The siemens software only provides baudrate up to 38400 so you can use a tool called mpi speed to setup the baudrate up to 115200 Baud This baudrate you have to configure in your PG TELE too Menuitem ISDN EAZ MSN The so called EAZ MSN is the device number of the TELE PROFessional Il on this telephone plug For the ISDN SO bus every cl
146. ration anyway APN APN ist he so called Service Point Name over which you establish your internet connection at yout provider Following names are currently known for T Mobile internet t mobile With this APN you only will get assigned a private IP Address and will not be reachable in the internet ca t mobile With this APN T Mobile will assign a public IP Addresse to the card Therewith you can use the DynDNS Option You have to activate this APN from T Mobile According to the last state the activation is free of charge and very quick a 76 2003 2011 by PI TIS Operating instructions Tele Network 7 1 3 3 1 Internetsettings In the network menu you can find the subitem internet Here you can change the settings which are necessary for an internet connection TELE PROF Il PRISDNST ni manual v provider 30 UMTS aa ande Absolutely important When connecting to the internet you should activate the firewall Never use your public IP Address for a direct communication This you can do in an emergency case e g first configuration via internet Always use a VPN Channel see below to communicate with your PLC or other devices which are connected to a TCP IP network Through operation via internet there can be additional costs Ask your provider for a suitable tariff Manual When choosing this connection type the other settings of this dialog are not relevant This means that th
147. re this address like 172 16 1 1 This address is also divided in 4 blocks Between these 4 blocks you can change with gt and lt The input will be finished with the ENTER key Please change only these IP address for your PG TELE because all other delivered devices has the same address So you don t have to make any thought about this menu item 6 2 9 Modem 6 2 9 1 Extension There are only two possible adjustments e YES The device is not connected directly to the line You then need either a prefix number or a certain key combination to get to the line e NO The device is either connected directly to the line i e you do not need prefix number in order to get a line or the device is within a private branch exchange and should call a partner within this system 6 2 9 2 Outline Code Here the key combination or the prefix number that are necessary for the connected telephone installation or each telephone set are set in order to call the line Possible Values 0 1 2 3 4 5 6 71 8 9 1 gt H W Numbers 0 to 9 If you have to dial for example 0 in order to get a line you have to input O here Earthing key R The earthing key can be input with the mathematical sign gt Flash key The flash key corresponds to the normal exclamation mark Break 1 8sec It is the Slash Break 2sec It is the comma 2003 2011 by PI TIS 59 Operating instructions Tele Network 6 2 9 3 Count of
148. rect connection to the control e PLC ONLINE e PLC OFFLINE Moreover after the first dialling the user is informed whether there is a connection or not e connected e not connected 5 2 2 2 Menu item Hang Up With this menu item the modem disconnects an existing connection i e it hangs up 5 2 2 3 Menu item Select Subscriber Select one of the maximally 197 saved entries by using the cursor up down key Then press ENTER for starting the actual dialling You can interrupt the dialling process by using the cursor left key This might become necessary if you accidentally dialled the wrong number 5 2 2 4 Menu item Edit subscriber This function enables you to input up to 197 names and telephone numbers in a telephone directory and save them there You have the storage positions 1 to 197 at your disposal If you are in this menu item you can select with the cursor keys UP DOWN your desired storage position 1 to 197 Press ENTER and the cursor moves to the input position 2003 2011 by PI TIS 25 Operating instructions Tele Network Number of the Subscriber name max 9 characters Mazs Paella tO pegin entry the connection Telefon number of the subcriber max 16 character or with you can use both entries and you have max 31 characters select next entry so Schema of LCD display for menu item Edit Subscriber Possible baud rates 12 33K Standartanruf ohne Besonderheiten R12 R3
149. ree Software Foundation Inc 51 Franklin Street Fifth Floor Boston MA 02110 1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed Preamble The licenses for most software are designed to take away your freedom to share and change it By con trast the GNU General Public License is intended to guarantee your freedom to share and change free software to make sure the software is free for all its users This General Public License applies to most of the Free Software Foundation s software and to any other program whose authors commit to using it Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead You can apply it to your programs too When we speak of free software we are referring to freedom not price Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software and charge for this service if you wish that you receive source code or can get it if you want it that you can change the software or use pieces of it in new free programs and that you know you can do these things To protect your rights we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights These restrictions translate to certain responsibilities for you if you distribute copies of the software or if you modify it For example if you dis
150. rget sector StartDWNr DW7 KF number of words 7 2 1 3 2 S7 If you use the plc option with an siemens s7 plc you have to look before programming the Communication DB for even dataword adresses So this Communication DB looks like this adress Value oo STRUCT 0 0 D 1 0 B 2 0 10 4 0 0 6 0 2 8 0 D 9 0 B 10 0 10 12 0 0 14 0 2 16 0 INTO 20 fT 1040 0 END_STRUCT Please note that you proofe the edited DB in your plc because there are often failures if you use in your Step 7 Software for editing your DB the declaration window or the data window 2003 2011 by PI TIS 91 7 2 1 4 Send data with the SPS TELE In order to send data to or fetch data from another plc you first have to define a communication flag word a communication data module and the PLC TELE flag in the TELE LINK The communication flag word and the PLC TELE flag always have to be input as an even number 0 2 4 6 254 In order to start the transmission and to call the subscriber 4 the plc now gives the following command to the communication flag word f ex FW 10 0104h The remaining data and the actual communication are executed according to the scheme defined in the DB Please note that you have selected the pg mux mode for pg mux see chapter 6 2 7 PG MUX Mode Only for PLC TELE and S5 92 2003 2011 by PI TIS Operating instructions Tele Network 7 3 RouterMode Example You want to c
151. rlauben Y erlauben os 2003 2011 by PI TIS 123 8 11 HMI Module With the HMl report module you can send PLC event depending SMS Pager Messages to practically as many recipients as you want without any programming effort The system classifies the messages to the corresponding recipient automatically and sends the message via correct provider By sending SMS additional costs can come up Please inform yourself at your provider That the HMI Module can work correctly you must set a few basical settings Following points have to be setted up o Pagerprovider o Pagerrecipients o PLC Connections o PLC Variables o Normierungen optional o Reports o Activate base setting HMI Option Even the HMI Module is secured by the Access protection via WEB Browser The necessary rights are given by the corresponding points 124 2003 2011 by PI TIS Operating instructions Tele Network Entering the pager provider Access rights Level Write Superuser Read View U2 TELE PROF Il name phone no protocol baudrate user 1 TD 1SMs 001712521001 SMS TAP ISDN a D2 SMS 001722278025 SMS UCP ISDN al SMS TAP ison xxx Pee Enter a statement under name which is expressive for you The phone number and the protocol type you can find out from your provider In the column Baudrate you can choose the connection of you
152. rotect will be activated automatically A acces to this device is only with PC with modem connection and password or with TELE PROFessional with firmware greater than 6 31 possible With the keypad you can switch off this dialing protection 7 3 4 1 Connection to a dialing protected TELE PROFessional ll 1 Edit modem user in the device 2 Select in edit subscriber for the telephone number the correct data set name 3 Begin to dial to this entry with select subscriber after connect you can work 96 2003 2011 by PI TIS Operating instructions Tele Network 7 3 4 2 Edit of the modem user with keypad and display e goto the menu item configuration acces code gt modem user e select with and the data set you want to edit Select it with the ENTER key now select the field complete name user name password direction you want to edit delete or store now press ENTER and you are in the edit mode with ESC your input will be stored after you are ready for editing you can store the data with the menu item save you can edit every time a new user Connecting with LAN ONLY for PG TELE IN the menu item IP addressbook you can edit your clients with the correct ip address The ip address can be seperated with the Or you write the DNS name down With the menu item connect IP address you select the client you want to connect Press ENTER to build the connection After you got the connect the Co
153. s are required For the SIMATIC S7 currently the connections are supported via MPI or TCP IP These connections should be projected in the following dialog Projecting the PLC Connections Access rights Level Write Superuser Read View U2 Connections ETS Ino name Connect MPIIP address active Cycle sec Delay sec laddress SMS status G0 1 PLC 2 S7 MPI OnBoard 2 x 1 60 MW 200 x E 2 Station mit CP S7 TCPAP 192 168 0 80 x 1 60 MW 100 x a 3 S7 MPI OnBoard 0 ol 61 62 G3 G4 G5 G6 G7 G8 G9 The column Name is provided for an own notation Connect is the connection type to the PLC here MPI or TCP IP Inthe column active you can define whether to communicate with the PLC or not Cycle defines the time periode after which the next communication to the PLC should start Address SMS status is for the feedback of the state of the HMI Module If you want to control communication state and the SMS shipment of the PLC enter the address of one word e g data block or flag TeleProf II will then write the maximum number of polling attempts for queued messages to the low byte in every communication cycle If the number 254 is exceeded so the number 254 is set every time If the number of polling attempts is gt 0 so the drop of a message has failed Like this the PLC can control the SMS shipment Now it should be controlled whether TelePro
154. s you about the software release of your TELE Network device 5 2 2 11 2 Remoteversion This menu item informs you about software release of the called TELE Network device If there is a more recent or older release a software update can be made see chapter 5 2 2 5 7 and Fehler Verweisquelle konnte nicht gefunden werden 5 2 2 11 3 Remotename In this menu item the device name of the called device is displayed In this way can check with which installation a connection has been built up This only works on the condition that the called device has a device name see chapter 6 2 2 Fehler Verweisquelle konnte nicht gefunden werden 5 2 2 11 4 Serial number With menu item you can check the serial number of the TELE PROFessional Normal this number is on the back side of the device and so you don t need to build out the device to get this information 5 2 2 11 5 MAC address Here you can see the internal MAC address of the TELE PROFessional This is an information you can use if you are looking for a problem in our network system 5 2 2 11 6 Copyright Copyrights of the TELE Network devices 1994 2008 by Pl amp TIS O 2003 2011 by Pl TIS 43 Operating instructions Tele Network 5 3 Status with LED The device can display the status of it with 5 LED They have folowing meaning Connect O analog or ISDN PLC SPS Data O O Error Modem Data 0 O LAN With the Connect LED the user knows if th
155. should enter the following address http 192 168 1 54 The Web Server of the TELE PROFessional will be started like following 2 TELE Professional II PIXISDNST Microsoft Internet Explorer Datei Bearbeiten Ansicht Favoriten Extras 2 gt x a yo Suchen Sie Favoriten O 2 2 m resse http 1192 168 1 54 home asp TELE PROF II PIxISDNST Now you can click with your mouse to the menu items on the left hand side and configure the device 2003 2011 by PI TIS 13 Operating instructions Tele Network 5 1 1 Access protection via WEB Browser From Version 6 70 the TELE Prof Il has an Access protection via WEB Browser Therefore we use the integrated login mechanism of your WEB Browser If no user exists yet the access will be granted without entering a password However a warning that your device is not protected from unauthorized access will appear on every page This can look for example like following A You can create several users with the corresponding rights under Configuration Access codes gt WEB user You will get the following input capabilities no full name user password password repeat su U1 U2 U3 U4 U5 RIE Ainnsreo Jaane nee ee OBO 14 2003 2011 by PI TIS Operating instructions Tele Network Please enter full name Username Password and the rights First and foremost you should create a Superuser right SU As soon as this one exists you will be asked f
156. stallation 143 9 4 2 1 1 Assignment of the normal telephone cord 9 4 2 1 1 1 Side of the modem Cry Y gt Ge Cc gt lt Earth A2 A B B2 Bell View from above on the western plug gold contacts facing down 6pin type In this way the assignment of the western socket in the modem is visible With the 4pin type the two pins at either end are left out 9 4 2 1 1 2 TAE plug Earth Bell View from above on the TAE plug from the front 9 4 2 1 2 World wide use of the TELE PROFessional ll modem connection Normally TAE socket and German cable can always be connected to the corresponding AB line In this way there is a protection against the connection of other phones as well 144 2003 2011 by PI TIS Operating instructions Tele Network Modem type Abu Dhabi Belgium G Czech Republic Dominikan Republic USA USA 2003 2011 by PI TIS 145 Serbia Spain USA Sweden Gwin maese with TAE socket 7 CH United Arab Emirates USA USA 1 The IDD line is normally available in every big firm in China otherwise the communication is very bad almost like a second parallel phone network 4 In Scandinavia please not that calling with inband signalling is possible without problems with the German modem However with pulse dialling the Scandinavian system differs form the German system d
157. t is possible to configure the PLC TELE in sucha way that a local PLC can be connected at the PLC socket of the PLC TELE and that a CP143 or a CP1430 H1 can be connected at the PG socket After the connection set up the programmer decides at the PG TELE whether he she wants to programme at the PLC or at the CP With the Bus calling of his her S5 software he she can reach and programme all the SIMATIC S5 PLCs that are connected to the L2 Bus With the menu item Special items and the submenu item To the PG PLC interface it is decided at the PG TELE whether the communication at the PLC TELE is via the PLC socket or the PG socket Possible adjustments e Connect PG socket with PLC socket normal setting e Connect PG socket with PG socket 2nd ple or switch to CP connection 114 2003 2011 by PI TIS Operating instructions Tele Network 8 6 Send data from the plc to a modem subscriber The plc can exchange data with a so called ASCll subscriber via data modules The ASCll subscriber is a normal modem Only V 42 BIS connections are allowed The caller might be either the ASCll subscriber or the plc or it can be started via the TELE LINK 8 6 1 Setup of the communication word between plc and TELE Network With each option that demands a common communication flag word between the plc and the TELE Network device the flag word is set up according to the following scheme and is read by the TELE Network device every 5 seco
158. t they want to assign stateful texts to the PLC values This can for example be the state of a multistage actuation unit state At the norming linear the text for sthe scale unit will stand here e g C pieces At the norming text the states are listed here with the following syntax lt comparison gt lt value gt lt text gt For each state a new line has to be entered lt comparison gt is optional If lt comparison gt is not entered the values will be compared to equality Example for actuation 0 OFF 1 step1 2 step2 For comparisions the following states can be defined aswell A temerature should be observed A text should be printed out whether the value is within limit or exceeded the limit The value is within limit as long as it is between 20 and 30 This looks like following gt 20 normal lt 30 normal O 2003 2011 by Pl TIS 129 lt 20 too low gt 30 too high gt 60 far too high As number enter the values which result from the conversion of the D 6b D fields plc value 1 HMI value 1 plc value 2 HMI value 2 Conversion For displaying the conversion of the numeric PLC value a physical value an assignement of the PLC value and the HMl value is necessary The displayed value is calculated like w m x t w the displayed value m HMI value2 HMI value1 PLC value2 PLC value1 HMI value1 m PLC value1 x
159. tands for the international code of the PG TELE for Germany the international code is 0049 If the return call is a national one just confirm with ENTER field remains empty If you have input a RC PNr you must not delete the ZERO of the prefix of the return call number This happens automatically when the TELE Network device dials This means that the return call number always remains completely in the entry O 2003 2011 by Pl TIS 111 8 1 3 Use recall mode In order to start the return call select after having made the aforementioned adjustments the respective subscriber in the menu item subscriber dialling As usual you start the dialling with ENTER and in this way you also start the return call The TELE Network devices communicate with each other exchange the return call numbers hang up immediately and then the PLC TELE calls back the other TELE Network device within a minute If there is no return call please check whether the adjustments in the TELE Network device PG TELE and PLC TELE are correct and whether the device that calls back had got a line 8 2 Operation of several plcs at one TELE Network device If you want to attend several automation devices that are not networked there are two possibilities to connect them to a TELE Network device 8 2 1 Operation with Siemens MUX 757 Connect the PLC s in a star shaped way with a MUX 757 of Siemens and connect the latter to a PLC TELE In this way you can progr
160. ted between device types that are configured differently PLC TELE PG TELE or PG TELE PLC TELE If the devics are of the same type PLC TELE PLC TELE or PG TELE PG TELE there will be the error report partner does not recognise option The TELE Network device that has received the programme programmes itself after the transmission While the programming is in process do not disconnect the device from the voltage supply since then the complete programme becomes invalid If the programme is invalid the device reports an ERROR If this message appears the device has to send to your local distributor After the programming the device executes a warm Start and after that it reports with the new software release yet with the same configuration 5 2 2 5 10 Fetch OS This command is used to get newer OS versions to TELE PROFessional ll devices with older versions Your own OS is will be replaced from the other OS of the other device via the telephone line to the programme memory In this way all TELE PROFessioanl ll devices can be updated with the most recent software release 30 Programmes can only be transmitted between device types that are configured differently PLC TELE PG TELE or PG TELE SPLC TELE If the devics are of the same type PLC TELE PLC TELE or PG TELE PG TELE there will be the error report partner does not recognise option The TELE Network device that has received the programme programmes itself after
161. th us modem This equipment complies with Part 68 of the FCC Rules On the soldering side of this equipment is a label that contains among other information the FCC Registration Number and Ringer Equivalence Number REN for this equipment You must upon request provide this information to your telephone company This equipment uses RJ12 plugs An FCC compliant telephone cord and modular plug are provided with this equipment This equipment is designed to be connected to the telephone network or promises wiring using a compatible modular jack which is part 68 compliant See installation instructions for details The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all those devices ring when your telephone number is called In most but not all areas the sum of the REN s of all devices connected to one line should not exceed five 5 0 To be certain of the number of devices you may connect to your line as determined by the REN you should contact your local telephone company to determine the maximum REN for your calling area If your telephone equipment causes harm to the telephone network the Telephone Company may discontinue your service temporarily If possible they will notify you in advance But if advance notice is not practical you will be notified as soon as possible You will be informed of your right to file a complaint with the FCC Your telephone company may make cha
162. that the subscriber definitely is a ASCII subscriber Otherwise use 01h Return messages of the TELE network device in the command byte 10h Modem connection with TELE LINK PLC TELE or PG TELE exists 20h The number of the desired subscriber entry is invalid 30h Modem connection does not exist anymore e g after hanging up or if the partner has hung up 40h Connect is not possible probably because line is busy 50h The command to hang up could not be executed 60h Modem connection with ASCll subscriber does not exist 116 2003 2011 by PI TIS Operating instructions Tele Network 8 6 2 Setup of the ASCII TELE flag Example FW 12 can be divided into FB 12 and FB 13 FW 12 FB 12 FB 13 direction of sending transmission status Direction of sending 0100H in the flag word absolutely 00 in the LOW byte also with PLC TELE in order to delete the status otherwise the TELE LINK does not accept the command gt send the data module that was described in the communication DB The number of the bytes that have to be sent can be found in the communication DB 0200H The plc is ready to receive data This means that the received lines are only written in the plc if this command is there Only one line including CR is written After that TELE inputs into the command flag OAH which means 020AH This means for the plc that data has been received After this data has been processed 0200H can be input again If there are
163. the GPL Basically if you distribute GPL software the license requires that you also distribute the source code to that GPL licensed software So if you distribute BusyBox without making the source code to the version you distribute available you violate the license terms and thus infringe on the copyrights of BusyBox This requirement applies whether or not you modified BusyBox either way the license terms still apply to you Read the license text for the details A note on GPL versions Version 2 of the GPL is the only version of the GPL which current versions of BusyBox may be distributed under New code added to the tree is licensed GPL version 2 and the project s license is GPL version 2 Older versions of BusyBox versions 1 2 2 and earlier up through about svn 16112 included variants of the recommended GPL version 2 or at your option later versions boilerplate permission grant Ancient versions of BusyBox before svn 49 did not specify any version at all and section 9 of GPLv2 the most recent version at that time says those old versions may be redistributed under any version of GPL including the obsolete V1 This was conceptually similar to a dual license except that the different licenses were different versions of the GPL However BusyBox has apparently always contained chunks of code that were licensed under GPL version 2 only Examples include applets written by Linus Torvalds util linux mkfs_minix c and util_linux
164. the ordinary GNU General Public License instead of this License to a given copy of the Library To do this you must alter all the notices that refer to this License so that they refer to the ordinary GNU General Public License version 2 instead of to this License If a newer version than version 2 of the ordinary GNU General Public License has appeared then you can specify that version instead if you wish Do not make any other change in these notices Once this change is made in a given copy it is irreversible for that copy so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy This option is useful when you wish to copy part of the code of the Library into a program that is not a library 4 You may copy and distribute the Library or a portion or derivative of it under Section 2 in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine readable source code which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange If distribution of object code is made by offering access to copy from a designated place then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code even though third parties are not compelled to copy the source along with the object code 5 A
165. the so called transparent mode The TELE Network device is adjusted to parameters that are specifically made for transmission e PG or PLC socket connection input from the TELE LINK that is called e Baud rate 300 1200 1800 2400 4800 9600 19200 38400 Baud e Number of data bits 5 to 8 bits e Parity N none E even O odd e Number of stop bits 1 1 5 and 2 bits 7 5 3 Direct Mode ON If there is a connection between PG TELE and PLC TELE the direct mode can be turned on with this menu item This mode is valid until the transmission is disconnected by using the LEFT key 7 5 4 Direct Mode On with HW If there is a connection between PG TELE and PLC TELE the direct mode can be turned on with this menu item This mode is valid until the transmission is disconnected by using the cursor left key With this mode there is a hand shaked connection between the plc tele and the device you want to communicate Here is the DTR and DSR line used 2003 2011 by PI TIS 107 7 6 S7 CP mode emulation Since version V7 00 is the Tele Prof I able to simulate the communication to the S7 plc above a CP341 1 The configuration is able in the integrated web browser menu The menu name is S7 MPI Konfig INN E Switch the S7 CP Emulation to yes If you want to reach always one CP switch the use default dest mpi address to yes and define the default dest mpi address So all communication accesses
166. tirely well defined independent of the application Therefore Subsection 2d re quires that any application supplied function or table used by this function must be optional if the application does not supply it the square root function must still compute square roots These requirements apply to the modified work as a whole If identifiable sections of that work are not derived from the Library and can be reasonably considered independent and separate works in them selves then this License and its terms do not apply to those sections when you distribute them as sepa rate works But when you distribute the same sections as part of a whole which is a work based on the Library the distribution of the whole must be on the terms of this License whose permissions for other licensees extend to the entire whole and thus to each and every part regardless of who wrote it 164 2003 2011 by PI TIS Operating instructions Tele Network Thus it is not the intent of this section to claim rights or contest your rights to work written entirely by you rather the intent is to exercise the right to control the distribution of derivative or collective works based on the Library In addition mere aggregation of another work not based on the Library with the Library or with a work based on the Library on a volume of a storage or distribution medium does not bring the other work un der the scope of this License 3 You may opt to apply the terms of
167. to the external modem 6 2 9 15 Ext modem baud Here you can define the serial speed for the communication to a defined external modem or handy Possible values are from 9600 up to 115200 baud If you connect a handy to the device please note that a lot of handys onlay provide baudrates of 57600 or 19200 baud That for the connection used PLC V24 port has the same pinning like a PC you can try to communicate with your pc and a terminal software to this modem to get the information of the baudrate Connect the handy modem to your PC start a terminal software Hyperterminal ZOC and define the communication baudrate you think its correct Now after the activation of this type in your software an AT and press Enter Get you an OK for answer the selected baudrate is ok it is provided from the modem handy So with this way you can get the maximum possible baudrate for communication This baudrate you select in this menu item connect the device to the TELE PROFessional ll and then restart it Now the devices beginns to restart and the connected external modem handy is the standard modem for the analog communication 2003 2011 by PI TIS 63 Operating instructions Tele Network 6 2 10 Connection 6 2 11 Recallmode Only for PLC TELE Here you can turn the return call mode on or off Possible adjustments YES NO This menu item is only necessary for the PLC TELE 6 2 12 Recallnumber Only for PG TE
168. too and can have the values between O and 255 More than two million of such networks are addressable First of all these networks are assigned to smaller firms with a direct internet connection and smaller Internet Providers As there is only one number left which can have the value between 0 and 255 a Class C Network can only have up to 255 hosts One number of it is reserved so there are only 254 possible hosts left 7 3 2 Netzmask Subnetmask The netmask or Subnetmask is a bit mask which separates the IP Address in a network and a host part A netmask is as long as the IP Address 32 Bit in IP Version 4 and 128 Bit in IP Version 6 on which it is used Every bit of the netmask relates to exactly one bit of the IP Address Every bit of the netmask which is set to 1 marks the corresponding bit of the IP Address as network part which addresses the particular subnet The bits set to O mark the host part with which each computer in this subnet is addressed The notation of a netmask is mainly not in binary but like the IP Addresses in the dotted decimal notation With the foundation of CIDR the netmask was only a decimal number which specified the used network part Examples the first three entries correspond the origin network classes A to C Netzmask binary Netzmask decimal Netzmask CIDR 11111111 00000000 00000000 00000000 255 0 0 0 8 11111111 11111111 00000000 00000000 255 255 0 0 16 11111111 11111111 11111111 00000000 2
169. tough sheet steel casing with a flange e optional power supply 24V DC or 230V DC 24V plug in power supply 350mA e circuit arrangement that fits the EMV e easy handling because of menu drive and LCD display in the uncoded text e easy and fast configuration because of the menu item first configuration e in the PG a software driver is not necessary the complete handling is taken over by the TELE PROFessional ll after dialling the target system the plc is on your desk inclusively the interface cable You communicate only serial with port PG RS232 e only one device for several controls Siemens S5 8 S7 AEG Allen Bradley Bosch Mitsubishi Klockner Moeller GE Fanuc Selectron Tele Mechanique Premium TSX57 e safe data transmission because of a multiply protected data protocol e g modules are only transmitted to the plc after they have been checked for their correctness e all PG functions can be carried out via the telephone line or the portable phone 2003 2011 by PI TIS 9 Operating instructions Tele Network e PG coupling possible e world wide use possible connection to GSM net optional e high data protection because of multistage password levels e optimisation of telephone costs because of the recall function e telephone register for 197 phone numbers is integrated into the TELE device this guarantees quick and easy calling of the desired target system e compatible world wide to all TELE
170. tribute copies of such a program whether gratis or for a fee you must give the recipients all the rights that you have You must make sure that they too receive or can get the source code And you must show them these terms so they know their rights We protect your rights with two steps 1 copyright the software and 2 offer you this license which gives you legal permission to copy distribute and or modify the software Also for each author s protection and ours we want to make certain that everyone understands that there is no warranty for this free software If the software is modified by someone else and passed on we want its recipients to know that what they have is not the original so that any problems introduced by others will not reflect on the original authors reputations Finally any free program is threatened constantly by software patents We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses in effect making the program pro prietary To prevent this we have made it clear that any patent must be licensed for everyone s free use or not licensed at all The precise terms and conditions for copying distribution and modification follow TERMS AND CONDITIONS FOR COPYING DISTRIBUTION AND MODIFICATION 0 This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public L
171. trolle y Hardware RTS CTS Speicherplatz 5 Modulationsverfahren ly 3600bpsV 32 Speicherplatz 6 Ergebnisanzeige Alphanumerisch Speicherplatz 7 auto Rufannahme y 1 Rina Speicherplatz 8 SMS Mode Inaktiv Speicherplatz 9 SIM Karten PIN Speicherplatz 10 zus Einstellung amp T Service Nr Fax Remote Einwahl Passwort Modus Ruckrufnummer Passwort Anruf Identifikation Modus y Inaktiw CallerlD 1 CallerlD 2 PIN Nummer nicht vergessen Ye OK x Abbrechen The Phoenix Modem will be connected to the PLC V24 connector of the Tele Prof I with a null modem cable This is the same cable which is used for the connection with a PC At devices which are used for the S5 remote maintenance the S5 controller can not be connected as usual anymore In this case the S5 controller has to be connected to PG TTY connector The connection cable for this can be ordered with the order number 9359 90 2003 2011 by PI TIS 87 When the modem supplied with power it has to be parametered in the Tele Prof ll which can be doen best over the Web Browser Configuration in TP II 3 TELE Professional II PIxISDNST Microsoft Internet Explorer Datei Bearbeiten Ansicht Favoriten Extras Q Zur ck v E A pe Suchen Pe Favoriten E B cae a bag 3 Adresse 148 http 192 168 1 54 home asp TELE PROF Il PHISDNST The GSM Modem has to be connected with the PLC V24 con
172. tware which is copyrighted by the Free Software Foundation write to the Free Software Foundation we sometimes make exceptions for this Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally NO WARRANTY 2003 2011 by PI TIS 161 11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE THERE IS NO WARRANTY FOR THE PROGRAM TO THE EXTENT PERMITTED BY APPLICABLE LAW EXCEPT WHEN OTHER WISE STATED IN WRITING THE COPYRIGHT HOLDERS AND OR OTHER PARTIES PROVIDE THE PROGRAM AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED IN CLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FIT NESS FOR A PARTICULAR PURPOSE THE ENTIRE RISK AS TO THE QUALITY AND PERFORM ANCE OF THE PROGRAM IS WITH YOU SHOULD THE PROGRAM PROVE DEFECTIVE YOU AS SUME THE COST OF ALL NECESSARY SERVICING REPAIR OR CORRECTION 12 INNO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER OR ANY OTHER PARTY WHO MAY MODIFY AND OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE BE LIABLE TO YOU FOR DAMAGES INCLUDING ANY GENERAL SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OT
173. u do not accept this License Therefore by modifying or distributing the Library or any work based on the Library you indicate your acceptance of this License to do so and all its terms and conditions for copying distributing or modifying the Library or works based on it 10 Each time you redistribute the Library or any work based on the Library the recipient automatically receives a license from the original licensor to copy distribute link with or modify the Library subject to these terms and conditions You may not impose any further restrictions on the recipients exercise of the rights granted herein You are not responsible for enforcing compliance by third parties to this License 11 If as a consequence of a court judgment or allegation of patent infringement or for any other reason not limited to patent issues conditions are imposed on you whether by court order agreement or oth erwise that contradict the conditions of this License they do not excuse you from the conditions of this License If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations then as a consequence you may not distribute the Library at all For ex ample if a patent license would not permit royalty free redistribution of the Library by all those who re ceive copies directly or indirectly through you then the only way you could satisfy both it and this License would be to refrain entirely
174. ultiplexer PG BUS dialling via a coordinator e g 923 C or via the IBX Bus Bus system of Pl with PG BUS dialling special type of PLC TELE The built in Multiplexer is not active in this operation mode e PLC S7 300 400 This device is connected to a S7 300 400 PLC e PLC S7 200 9K6 This device is connected to a S7 200 plc and communicates with 9600 Baud on port PLC V24 e PLC S7 200 19K2 This device is connected to a S7 200 plc and communicates with 19200 Baud on port PLC V24 e PLC S5 F Type This device is connected to S5 plc especially a F Type e PLC PILZ This device is connected to PILZ PSSxxx plc you should connect the PLC with its own programming cable e PLC Allen Bradley This device is connected to a Allen Bradley SLC5 plc and communicates with the DH485 or DF 1 mode 32 2003 2011 by PI TIS Operating instructions Tele Network 5 2 2 6 3 Menu item MPI OnBoard Y N e Yes The build in mpi profibus connector is activated and be used e No The build in mpi profibus connector is deactivated 5 2 2 6 4 Menu item MPI OnBoard Baud With this menu item you can define the speed of the connected mpi profibus Please check this baudrate because so there is no communication possible or your bus system will be stopped 5 2 2 6 5 Menu item OnBoard MPI Adr With this menu item you define the address of the TELE PROFessional ll as a bus client This address must be a unused address for the bus If you use the default ad
175. umeric Scall Skyper Quix alphanumeric ANP Belgacom numeric and alphanumeric For your further information it exists for the sms kommunication different protocolls to the sms data server In this option are following protocolls implemented TAP and UCP The TAP is for D1 and E Plus UCP is for D2 Befor you give the TELE Network device the command to start this operation you have to select in the COM DB the right pager type In the subscriber database of the TELE device you have to enter the telefonnumber of the data server of the pager 2003 2011 by PI TIS 101 Numbers for Germany pager type Number protocol maximum length of the sending data in characters D1 SMS 01712521002 160 16000 S Cityrufnumber _ 01691 special 180 Quix i 6591 special Gu Numeroj 02 fpa e aphanumeric n number of he pager Please remark that you have to edit the telefon number of the SCALL and SKYPER complete in the subscriber database of the TELE device For the other pagers you have to edit the telefon number in the PAGER COM DB Please note if you have problems with sending some sms proofe at first the telefon number of the central dialing number of your provider It is possible that this number has been changed Please contact your dealer of this device or the technical hotline of this device 102 2003 2011 by PI TIS Operating instructions Tele Network 7 4 2 1 1 Setup of the communication
176. w you can do these things To protect your rights we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it For example if you distribute copies of the library whether gratis or for a fee you must give the recipi ents all the rights that we gave you You must make sure that they too receive or can get the source code If you link a program with the library you must provide complete object files to the recipients so that they can relink them with the library after making changes to the library and recompiling it And you must show them these terms so they know their rights Our method of protecting your rights has two steps 1 copyright the library and 2 offer you this license which gives you legal permission to copy distribute and or modify the library Also for each distributor s protection we want to make certain that everyone understands that there is no warranty for this free library If the library is modified by someone else and passed on we want its recipi ents to know that what they have is not the original version so that any problems introduced by others will not reflect on the original authors reputations Finally any free program is threatened constantly by software patents We wish to avoid the danger that companies distributing free software
177. will individually obtain patent licenses thus in effect transforming the program into proprietary software To prevent this we have made it clear that any patent must be licensed for everyone s free use or not licensed at all Most GNU software including some libraries is covered by the ordinary GNU General Public License which was designed for utility programs This license the GNU Library General Public License applies to certain designated libraries This license is quite different from the ordinary one be sure to read it in full and don t assume that anything in it is the same as in the ordinary license The reason we have a separate public license for some libraries is that they blur the distinction we usu ally make between modifying or adding to a program and simply using it Linking a program with a library without changing the library is in some sense simply using the library and is analogous to running a utility program or application program However in a textual and legal sense the linked executable is a combined work a derivative of the original library and the ordinary General Public License treats it as such Because of this blurred distinction using the ordinary General Public License for libraries did not effec tively promote software sharing because most developers did not use the libraries We concluded that weaker conditions might promote sharing better However unrestricted linking of non free programs would depr
178. with a 9pin 1to1 male male cable to the plc or the profibus You can use also a standard profibus cable with its own connectors It can be provided bus systems from 9600 Baud up to 12 MBaud 9 4 9 1 PIN assignment for the MPI Profibus port PIN 1 N C PIN 2 N C PIN 3 Ltg_B MPI PPI Profibus line B PIN 4 RTS AS handshake to plc PIN 5 M5V signal ground PIN 6 5V Out 5V Out for terminal resistors PIN 7 N C PIN 8 Ltg_A MPI PPI Profibus line A PIN 9 RTS PG handshake to PG 154 2003 2011 by PI TIS Operating instructions Tele Network 9 4 10 Voltage Connection For the voltage supply of the TELE BOOK device either the provided plug in power supply or the existing power supply of 24V DC 20 with at least 625mA current is connected to the green 3pin plug The device can be switched on off with the power switch on the front side so you don t have to unplug plug the green power connector So as you can see the TELE PROFessional on the picture we have from up to down following pinning 24V DC PE PE must be connected allways OV 2003 2011 by PI TIS 155 9 5 Plc types The TELE Network device can be used with the following plc controls Siemens S5 90 U S5 95 U S5 100 U S5 90 U S5 115U F S5 135 U S5 155 U H S7 200 S7 300 S7 400 H1 function only for PLC S5 TELE devices L1 function only for PLC S5 TELE devices L2 function only for PLC S5 TELE devices FAX
179. word between plc and TELE Network With each option that demands a common communication flag word between the plc and the TELE Network device the flag word is set up according to the following scheme and is read by the TELE Network device every 5 seconds Example FW10 can be divided into FB10 and FB11 FW 10 FB 10 FB 11 command byte Number of the entry in the subscriber list Reference card for the command byte 01h Start dialling process to the pager Return messages of the TELE network device in the command byte 20h The number of the desired subscriber entry is invalid or the subscriber is empty 30h a DB is too small or doesn t exist or has wrong parameters e g the wrong pager number 40h Connect is not possible probably because line is busy 50h The command to hang up 02h could not be executed 60h Modem connection with ASCll subscriber does exist 70h A failure is ocured by sending the sms message 80h Sms message is sended correctly 90h Command doesn t exist or is not supported with this option 2003 2011 by PI TIS 103 7 4 2 1 2 Setup of the communication data module for S5 for PAGER The minimum length of the PAGER COM DB is 142 words DW 0 to DW141 DW 0 Coding of the pager types Format KF D1 or E Plus SMS with TAP OT Quixnumeric 5 Skyperalphanumeric 6 ANP Belgacom____________ 7 Proximus O This table of coding the pager types is growing for the future for
180. x baudrate to No the device gets the baudrate from your software and will use it This is an advantage for you so you can change the baudrate from the office you want and no one must chage the configuration of the plc If you have configured it to Yes the TELE PROFessional II will use the baudrate of its own configuration The advantage for this is that you can t define a baudrate greater than 1 5 MBaud in the programming software So you are connected to bus systems with baudrates 6 MBaud or 12MBaud and so you can tele service this bus systems The baudrate is fixed 6 2 4 6 MPI Profibus With this menu itm you define the profile of the connected mpi profibus Please note that you configure the correct profile for the connected bus system because the timing will be changed not that your bus system will be paused if you uses the wrong profile MPI Bus The connected bus system is a MPI bus Profi DP Stand The connected bus system is a profibus with the profil DP Standard Profi DP FMS The connected bus system is a profibus with the profil DP FMS 54 2003 2011 by PI TIS Operating instructions Tele Network 6 2 5 PC MPI cable 6 2 5 1 MPI cable Baud The in this menu item configured baudrate is the baudrate the connected PC communicates with the PG TELE The siemens software only provides baudrate up to 38400 so you can use a tool called mpi speed to setup the baudrate up to 115200 Baud This baudr
181. y It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified defini tions 2003 2011 by PI TIS 165 b Accompany the work with a written offer valid for at least three years to give the same user the materials specified in Subsection 6a above for a charge no more than the cost of perform ing this distribution c If distribution of the work is made by offering access to copy from a designated place offer equivalent access to copy the above specified materials from the same place d Verify that the user has already received a copy of these materials or that you have already sent this user a copy For an executable the required form of the work that uses the Library must include any data and utility programs needed for reproducing the executable from it However as a special exception the source code distributed need not include anything that is normally distributed in either source or binary form with the major components compiler kernel and so on of the operating system on which the executa ble runs unless that component itself accompanies the executable It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system Such a contradiction means you cannot use both them and the Library together in an executable that you d
182. y and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty keep intact all the notices that refer to this License and to the absence of any warranty and distribute a copy of this License along with the Library You may charge a fee for the physical act of transferring a copy and you may at your option offer war ranty protection in exchange for a fee 2 You may modify your copy or copies of the Library or any portion of it thus forming a work based on the Library and copy and distribute such modifications or work under the terms of Section 1 above pro vided that you also meet all of these conditions a The modified work must itself be a software library b You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change c You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License d If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility other than as an argument passed when the facility is invoked then you must make a good faith effort to ensure that in the event an application does not supply such function or table the facility still operates and performs whatever part of its pur pose remains meaningful For example a function in a library to compute square roots has a purpose that is en
183. y distribute the object code for the work under the terms of Section 6 Any executables containing that work also fall under Section 6 whether or not they are linked directly with the Library itself 6 As an exception to the Sections above you may also compile or link a work that uses the Library with the Library to produce a work containing portions of the Library and distribute that work under terms of your choice provided that the terms permit modification of the work for the customer s own use and reverse engineering for debugging such modifications You must give prominent notice with each copy of the work that the Library is used in it and that the Li brary and its use are covered by this License You must supply a copy of this License If the work during execution displays copyright notices you must include the copyright notice for the Library among them as well as a reference directing the user to the copy of this License Also you must do one of these things a Accompany the work with the complete corresponding machine readable source code for the Library including whatever changes were used in the work which must be distributed under Sec tions 1 and 2 above and if the work is an executable linked with the Library with the complete machine readable work that uses the Library as object code and or source code so that the user can modify the Library and then relink to produce a modified executable containing the modified Librar
184. yet To make a telephone call with ISDN modem is also possible For this you need another command Please look Connect Analogue ATDT012345 Connect ISDN ATDI012345 or ATDT012345 ISDN If you want to make a connect with ISDN you see this in the result message too Connect Analogue Connect 33200 or sometimes a less baudrate Connect ISDN Connect ISDN 2003 2011 by PI TIS 139 9 Technical data of the Tele Professional ll 9 1 Mechanical Data Dimensions metall case 279 x 68 x 165 mm Working temperature 5 to 55 degree Celsius PLC interface TTY 20mA current loop PLC TELE active plc control passive or V24 completely same pinning like a PC PG interface TTY 20mA current loop 100 mechanically and electrically compatible or V24 with 1to1 cable form the PC MPI Profibus Pinning like a plc connecting to a profius connector and profibus cable possible Ethernet connector RJ 45 Plug for directconnection to the network plug A connection to a PC with a Cross Over cable possible ISDN modem RJ 45 Plug for direct connection to the SO bus Analogue modem 33600 HIGH SPEED V 42 BIS MNP5 9 2 Electrical Data Supply Voltage 24V DC input range 18 36V The supplied 24V are at the user s disposal at the PG socket without any restrictions Input 15 VA Functional control voltage and watchdog supervision 140 2003 2011 by PI TIS Operating instructions Tele Network 9 3 US FCC Rules for devices wi

TELE-Network

Contents

Download Pdf Manuals

Related Search

Related Contents