Home

MX666/MW665 Digital Projector User Manual

1. Reference and further fine tune the image based on the selections listed on the Mode n page below See Setting the User User 2 mode on page 32 or details Adjusts the brightness of the image See Adjusting Brightness on Brightness page 33 for details Adjusts the degree of difference between dark and light in the image Contrast See Adjusting Contrast on page 33 for details Adjusts the color saturation level the amount of each color in a Colo video image See Adjusting Color on page 33 for details r c This function is only available when a Video S Video or Component Video N signal is selected y Adjusts the red and green color tones of the image See Adjusting O Tint Tint on page 33 for details c CF This function is only available when a Video or S Video signal is selected a Adjusts the image to make it look sharper or softer See Adjusting Sharpness on page 33 for details 3 Sharpness D E c This function is only available when a Video S Video or Component Video c signal is selected Brilliant Color See Adjusting Brilliant Color on page 33 for details Color Temperature See Selecting a color temperature on page 33 for details Color Temperature See Setting a preferred color temperature on page 34 for details Fine Tuning 3D Color Management See 3D Color Management on page 34 for details Reset Picture Settings See Resetting current or all picture modes on page 35 for details i vo
2. Timing Resolution Vertical Horizontal Pixel Frequency Frequency Hz Frequency kHz MHz 480i 720 x 480 59 94 15 73 13 5 480p 720 x 480 59 94 31 47 27 576i 720 x 576 50 15 63 13 5 576p 720 x 576 50 31 25 27 720 50p 1280 x 720 50 37 5 74 25 720 60p 1280 x 720 60 45 00 74 25 1080 50i 1920 x 1080 50 28 13 74 25 1080 60i 1920 x 1080 60 33 75 74 25 1080 24P 1920 x 1080 24 27 74 25 1080 25 1920 1080 25 28 13 74 25 1080 30P 1920 x 1080 30 33 75 74 25 1080 50P 1920 x 1080 50 56 25 148 5 1080 60P 1920 x 1080 60 67 5 148 5 Cr Supported timing for 3D signal in Frame Sequential format Displaying a 1080i 1125i 60Hz or 1080i 1 125i 50Hz signal may result in slight image vibration Supported timing for Video and S Video inputs Video mode Horizontal Vertical Frequency Color sub carrier Frequency kHz Hz Frequency MHz NTSC 15 73 60 3 58 PAL 15 63 50 4 43 SECAM 15 63 50 4 25 or 4 41 PAL M 15 73 60 3 58 PAL N 15 63 50 3 58 PAL 60 15 73 60 4 43 NTSC4 43 15 73 60 4 43 Supported timing for 3D signal in Frame Sequential format Specifications Warranty and Copyright information Limited warranty BenQ warrants this product against any defects in material and workmanship under normal usage and storage Proof of purchase date will be required with any warranty claim In the event this product is found to be defective within the warranty period
3. BenQ MX666 MW 665 Digital Projector User Manual Table of contents Important safety instructions 3 Introduction 7 Projector features 7 Shipping contents 8 Projector exterior view 9 Controls and functions 10 Positioning your projector 16 Choosing a location l6 Obtaining a preferred projected image SIZE H 17 19 Connecting video source devices 20 Connecting smart devices 666 21 Operation 22 Starting up the projector 22 Adjusting the projected image 23 Using the menus 25 Securing the projector 26 Switching input signal 28 Magnifying and searching for details 29 Selecting the aspect ratio 29 Optimizing the 32 Setting the presentation timer 35 Remote paging operations 36 Freezing the 36 Hiding the 37 Locking control keys 37 Ope
4. Lens cap Focus and Zoom ring Vent cool air intake Speaker grill Front IR remote sensor Projection lens Audio L R input jacks Audio output jack Audio input jack HDMI input port HDMI MHL input port S Video input jack Video input jack RGB PC Component Video YPbPr YCbCr signal input jack RS232 control port RGB signal output jack USB Mini B port USB Type A port RJ45 LAN input jack AC power jack Kensington anti theft lock slot Rear adjuster foot Ceiling mount holes Introduction 9 10 Controls and functions Projector MX666 e OCOY Focus ring II Adjusts the focus of the projected image Zoom ring Adjusts the size of the image Rear IR remote sensor MENU EXIT Turns on the On Screen Display OSD menu Goes back to previous OSD menu 13 exits and saves menu settings 5 POWER Toggles the projector between standby mode and on lt Left 16 Decreases the projector volume 15 Keystone Arrow keys D lt Left gt Right Manually corrects distorted images resulting from an angled projection MODE ENTER Selects an available picture setup mode Activates the selected On Screen Display 16 OSD menu item ECO BLANK Used to hide the screen picture POWER indicator light Lights up or flashes when the projector is under operation Introduction e 6eec TEMPerature wa
5. The POWER indicator light is a steady orange and fans stop Disconnect the power cord from the power outlet C3 To turn off the power ring tone see Turning off the Power On Off Ring Tone on page 38 for details Ifthe projector is not properly shut down to protect the lamp when you attempt to re start the projector the fans will run for a few minutes to cool down Press POWER or ON again to start the projector after the fans stop and the POWER indicator light turns orange Lamp life results will vary depending on environmental conditions and usage Direct power off The AC power cord can be pulled out right after the projector is turned off To protect the lamp wait about 10 minutes before re starting the projector When you attempt to re start the projector the fans may run for a few minutes to cool down In such cases press POWER or again to start the projector after the fans stop and the POWER indicator light turns orange Operation 41 Menu operation Menu system Please note that the on screen display OSD menus vary according to the signal type selected and the projector model you are using Main menu Sub menu Options Wall Color Off Light Yellow Pink Light Green Blue Blackboard Aspect Ratio Auto Real 4 3 16 9 16 10 2D Keystone Position Phase H Size Digital Zoom
6. uick Auto 2 See Switching input signal on page 28 for details A o m 48 Operation Function Description Presentation Reminds the presenter to finish the presentation within a certain time Timer frame See Setting the presentation timer on page 35 for details Sets the language for the On Screen Display OSD menus See Using Language the menus on page 25 for details Projector The projector can be installed on a ceiling or behind a screen or with Installation one or more mirrors See Choosing a location on page 16 for details Menu Display Time Sets the length of time the OSD will remain active after your last key press Menu Menu Position Settings Sets the On Screen Display OSD menu position Reminder Message IN Sets the reminder messages on or off wn Direct Power On a Allows the projector to turn on automatically once the power is fed a through the power cord m x Signal Power On n Sets whether to turn the projector directly on without pressing POWER ON when the projector is standby mode and the signal S is feed through the cable w Auto Power Off b Allows the projector to turn off automatically if no input signal is a detected after a set period of time See Setting Auto Power Off on 3 page 54 for details Quick Cooling a Operation Enables or disables the Quick Cooling function Selecting On enables Settings the function and projector cooling time will be shortened from
7. 1 Mode Auto Top Bottom Frame Sequential DISPLAY krame Packing Side by Side Off 3D Sync Invert Disable Invert 3D Apply 3D 3D Settings 1 3D Settings 2 3D Settings Settings 3 Off Save 3D Settings 7 Settings 1 3D Settings 2 3D Settings Blackboard Off Letter Formation Worksheet Teaching Coordinate Chart Template Whiteboard Off Letter Formation Worksheet Coordinate Chart Picture Mode Dynamic Presentation sRGB Cinema 3D User User 2 Reference Mode Dynamic Presentation sRGB Cinema 3D Brightness Contrast Color Tint Sharpness 2 Brilliant Color On Off PICTURE Color Temperature Cool Normal Warm R Gain G Gain B Gain R Offset G Color Temperature Fine Tuning Offset B Offset Primary Color R G B C M Y 3D Color Hue Management Saturation Gain Reset Picture Settings Current All Cancel 3 Quick Auto Search On Off SOURCE Color Space Conversion Auto RGB YUV Operation Main menu Sub menu Options 4 SYSTEM SETUP Basic Timer Period 1 240 minutes Timer Display Always 3 min 2 min min Never Timer Position Presentation Top Left Bottom Left Top Right Bottom Right Ti asd Timer Counting Count Down Count Up Direction Sound Reminder On Off On Off English Frangais Deutsch Italiano Espafiol lij f rh 8 0 Language Svenska Nederlands T rkce e tina Portugu s Inu Polski Magyar Hrvatski Norsk Dans
8. Previous Play Pause Next lt lt Rewind m Stop Fast forward Goes to the previous file Plays Pauses Goes to the next file Rewinds Stops Fast forwards during media playback Only available when controlling your smart device in MHL mode ZOOM ZOOM Magnifies or reduces the projected picture size Introduction 11 11 19 MUTE Operate your display software program Toggles projector audio between on and on a connected PC which responds to off page up down commands like Microsoft 20 ASPECT PowerPoint Selects the display aspect ratio 12 FREEZE 21 SMART ECO Freezes the projected image Displays the Lamp Mode menu for 13 NETWORK SETTING selecting a suitable lamp operating mode Displays the Network Settings OSD 22 Numeric buttons menu Enters numbers in network settings 14 QUICK INSTALL Quickly selects several functions to adjust the projected image and displays the test The Laser Pointer isa Avoid Exposure ig pattern presentation aid for professionals It emits red 15 AUTO colored light when you press it Automatically determines the best picture timings for the displayed image Operating the LASER pointer emitted from this aperture The laser beam is visible It is necessary to press and hold 16 p Right 1 LASER for continuous output Increases the projector volume When the On Screen Display OSD menu is activated the 3 5 and 16 keys are
9. SmartEco technology The SmartEco technology lowers the power consumption and increases the lamp life ECO BLANK saves the lamp power Pressing the ECO BLANK button to hide the image and immediately lower the lamp power at the same time Constant brightness MW665 In the LumenCare mode constant brightness can be achieved HDMI MHL compatible MX666 You can project the content from your smart devices via HDMI MHL connection Less than 0 5W in standby condition Less than 0 5W power consumption under standby mode Filter Free Filter free design to lower maintenance and operating costs One key auto adjustment Pressing AUTO on the keypad or remote control to show the best picture quality immediately Built in speaker s Built in speaker s providing mixed mono audio when an audio input is connected Quick Cooling Auto Power Off Signal Power On Direct Power On Quick Cooling function speeds up the cooling process when turning off the projector Auto Power Off function allows the projector to turn off automatically if no input signal is detected after a set period of time Signal Power On function turns on your projector automatically once detecting the signal input and Direct Power On turns your projector when the power is fed Instant Restart Selectable Instant Restart function enables you to restart the projector immediately within 90 seconds after turning it off 3D Function supported Various 3D formats make the 3D function m
10. Through The projector can play sound when it is in standby mode and the corresponding jacks are correctly connected to devices Press lt gt to choose the source that you wish to use See Connection on page 19 for how to make the connection cr MHL Charging MX666 Selecting On enables the function The projector will automatically charge the connected MHL compatible smart device as long as the power is fed to the projector Enabling this function slightly increases the standby power consumption Network Settings See BenQ Network Projector Operation Guide for details Reset All Settings Returns all settings to the factory preset values c The following settings will still remain Position Phase H Size User 1 User 2 Color Space Conversion Projector Installation High Altitude Mode Security Settings Baud Rate and Network Settings Operation 51 Function Description Source Shows the current signal source Picture Mode Shows the selected mode the PICTURE menu Lamp Mode Shows the current lamp mode 2 Resolution Current Shows the native resolution of the input signal z System Status 3D Format 2 Shows the current 3D mode 3 Color System m Shows input system format Equivalent Lamp Hour Displays the number of hours the lamp has been used Firmware Version Shows the firmware version of your projector 54 USB U READER available d only whena See Presenting fr
11. hearing viewers Teaching template Enters Teaching template setting directly Introduction 13 Remote control effective range The remote control must be held at an angle within 30 degrees perpendicular to the projector s IR remote control sensor s to function correctly The distance between the remote control and the sensor s should not exceed 8 meters 26 feet Make sure that there are no obstacles between the remote control and the IR sensor s on the projector that might obstruct the infra red beam 14 Introduction Replacing the remote control batteries To open the battery cover turn the remote control over to view its back push on the finger grip on the cover and slide it up in the direction of the arrow as illustrated The cover will slide off Remove any existing batteries if necessary and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment Positive goes to positive and negative goes to negative Refit the cover by aligning it with the base and sliding it back down into position Stop when it clicks into place Avoid leaving the remote control and batteries in an excessive heat or humid environment like the kitchen bathroom sauna sunroom or in a closed car Replace only with the same or equivalent type recommended by the battery manufacturer Dispose of the used batteries according to the
12. in the projector and in some instances the lamp may explode Go to http lamp beng com for a replacement lamp A The LAMP indicator light and TEMPerature warning light will light up if the lamp becomes too hot Turn the power off and let the projector cool for 45 minutes If the Lamp or Temp indicator still lights up after turning the power back on please contact your dealer See Indicators on page 59 for details The following Lamp warning displays will remind you to change the lamp Status Message Install a new lamp for optimal performance If the projector is normally run with Economic selected See Getting to know the lamp hour on page 54 you may continue to operate the projector until the next hour lamp warning appears Order a new lamp at lamp benq com Press MODE ENTER to dismiss the message Order Replacement Lamp Lamp gt XXXX Hours It is strongly recommended that you replace the lamp at this age The lamp is a consumable item The lamp brightness diminishes with use This is normal lamp behavior You can replace the lamp whenever you notice that the brightness level has eine OE Hours significantly diminished Replace Lamp Soon Order a new lamp at lamp beng com Press MODE ENTER to dismiss the message OK Replace Lamp Now Lamp XXXX Hours Lamp usage time exceeded Order a new lamp at lamp benq com The lamp MUST be replaced before the projector will operate normally Pr
13. light on the projector lights orange after power has been applied Press 0 POWER or JON to start the projector As soon as the lamp lights up a Power On Tone will be heard The POWER indicator light flashes green and stays green when the projector is on The start up procedure takes about 30 seconds In the later stage of start up a startup logo is projected If necessary Rotate the focus ring to adjust the image clearness To turn off the ring tone see Turning off the Power On Off Ring Tone on page 38 for details CF If the projector is still hot from previous activity it will run the cooling fan for approximately 90 seconds before energizing the lamp 3 If the projector is activated for the first time select your OSD language following the on screen instructions If you are prompted for a password press the arrow keys to enter a six digit password See Utilizing the password function on page 26 for details Switch all of the connected equipment on The projector will start to search for input signals The current input signal being scanned displays in the upper left corner of the screen If the projector doesn t detect a valid signal the message No Signal will continue displaying until an input signal is found You can also press SOURCE on the projector or remote control to select your desired input signal See Switching input signal on page 28 for details Please select lan
14. lt q Left MODE ENTER 18 Selects an available picture setup mode Activates the selected On Screen Display 19 OSD menu item ECO BLANK Used to hide the screen picture 20 Keystone Arrow keys W AUp O 21 Y Down Manually corrects distorted images resulting from an angled projection SMART ECO Displays the lamp mode selection bar 22 Aspect Selects the display aspect ratio 23 Page Up Page Down Operate your display software program on a connected PC which responds to page up down commands like Microsoft PowerPoint Digital Zoom Digital Zoom Magnifies or reduces the projected picture size Timer On Activates or displays an on screen timer based on your own timer setting Timer Set up Enters presentation timer setting directly 3D settings Enters 3D settings directly AUTO Automatically determines the best picture timings for the displayed image gt Right When the On Screen Display OSD menu is activated the 4 7 and 16 keys are used as directional arrows to select the desired menu items and to make adjustments SOURCE Displays the source selection bar Volume Adjusts the sound level Mute Toggles projector audio between on and off Freeze Freezes the projected image QUICK INSTALL Quickly selects several functions to adjust the projected image and displays the test pattern cc Displays the video term description on screen which is provided for hard of
15. manufacturer s instructions and local environment regulations for your region Never throw the batteries into a fire There may be danger of an explosion If the batteries are dead or if you will not be using the remote control for an extended period of time remove the batteries to avoid damage to the remote control from possible battery leakage Introduction 15 Positioning your projector Choosing a location Your projector is designed to be installed in one of four possible installation locations 16 Front Table Select this location with the projector placed on the table in front of the screen This is the most common way to position the projector for quick setup and portability 2 Front Ceiling Select this location with the projector suspended upside down from the ceiling in front of the screen Purchase the BenQ Projector Ceiling Mount Kit from your dealer to mount your projector on the ceiling Set Front Ceiling in the SYSTEM SETUP Basic gt Projector Installation menu after you turn the projector on 3 Rear Ceiling Select this location with the projector suspended upside down from the ceiling behind the screen Note that a special rear projection screen and the BenQ Projector Ceiling Mount Kit are required for this installation location Set Rear Ceiling in the SYSTEM SETUP Basic gt Projector Installation menu after you turn the projector on 4 Rear Table Select this lo
16. reference only The rear connecting jacks available on the projector vary with each projector model Notebook or desktop Monitor computer Smartphone or tablet PC um Connection 19 adapter cable 5 S Video cable l VGA cable 6 Video cable 2 VGA to DVI A cable 7 Audio cable 3 USB cable 8 Audio L R cable 4 Component Video to VGA D Sub 9 USB flash drive USB wireless dongle 0 HDMI cable l HDMI Micro USB cable Many notebooks do not turn on their external video ports when connected to a projector Usually a key combo like FN or CRT LCD key turns the external display on off Locate a function key labeled CRT LCD or a function key with a monitor symbol on the notebook Press FN and the labeled function key simultaneously Refer to your notebook s documentation to find your notebook s key combination The D Sub output only works when an appropriate D Sub input is made to the COMPUTER jack Ifyou wish to use this connection method when the projector is in standby mode make sure the Monitor Out function is turned on in the SYSTEM SETUP Advanced menu See Standby Settings on page 51 for details Connecting video source devices You need only connect the projector to a video source device using just one of the connecting methods however each provides a different level of video quality T
17. surface is not white See Using Wall Color on page 32 for details Aspect Ratio There are several options to set the image s aspect ratio depending on your input signal source See Selecting the aspect ratio on page 29 for details 2D Keystone Corrects any keystoning of the image See Correcting keystone on page 24 for details Displays the position adjustment page To move the projected image use the directional arrow keys The values shown on the lower position of the page change with every key press you made until they Position reach their maximum or minimum Cr This function is only available when a PC signal analog RGB is selected Adjusts the clock phase to reduce image distortion Phase Cr This function is only available when a PC signal analog RGB is selected Adjusts the horizontal width of the image H Size This function is only available when a PC signal analog RGB is selected Digital Zoom Magnifies or reduces the projected image See Magnifying and searching for details on page 29 for details 46 Operation Function Description nu uu AV IdSIQG 1 w This projector features a 3D function which enables you to enjoy the 3D movies videos and sporting events in a more realistic way by presenting the depth of the images You need to wear a pair of 3D glasses to view the 3D images 3D Mode The default setting is Auto and the projector
18. the timer perform the following steps Go to the SYSTEM SETUP Basic gt Presentation Timer menu and highlight Off Press MODE ENTER A confirmation message displays 2 Highlight Yes and press MODE ENTER to confirm You will see the message Timer is Off displaying on the screen Remote paging operations Connect the projector to your PC or notebook with a USB cable prior to using the paging function See Connection on page 19 for details You can operate your display software program on a connected PC which responds to page up down commands like Microsoft PowerPoint by pressing PAGE PAGE or Page Up Page Down on the remote control If remote paging function doesn t work check if the USB connection is correctly made and the mouse driver on your computer is updated to the latest version C The remote paging function cannot work with Microsoft Windows998 operating system Windows XP higher operating systems are recommended Freezing the image Press FREEZE on the remote control to freeze the image The word FREEZE will display in the upper left corner of the screen To release the function press any key on the projector or remote control CF If your remote control has the following keys please note that they cannot be pressed to release the function LASER Page Up Page Down Even if an image is frozen on the screen the pictures are running on the video or other device If the connected
19. to Micro USB adaptor you can connect your smart devices to the projector and then enjoy your content on the big screen CZ Some smart devices may not be compatible to the cable that you use Please consult the manufacturer of your smart device for detailed information Using a HDMI to Micro USB cable l Take a HDMI to Micro USB cable and connect one end to the HDMI input connector on the projector 2 Connect the other end to the Micro USB output socket on your smart device 3 Switch to the HDMI MHL input source To switch input signal see Switching input signal on page 28 for details Using a HDMI to Micro USB adaptor and a HDMI cable l Take a cable and connect one end to the HDMI input connector on the projector Connect the other to the HDMI input socket on the adaptor 3 Connect the other of the adaptor to the Micro USB output socket on your smart device 4 Switch to the HDMI MHL input source To switch input signal see Switching input signal on page 28 for details Connection 21 Operation 22 Starting up the projector Please use the original accessories e g power cord only with the device to avoid possible dangers such as electric shock and fire 2 Plug the power cord into the projector and into power outlet Turn on the power outlet switch where fitted Check that the POWER indicator
20. to its original size You can also press W repeatedly until it is restored to the original size CT The picture can only be navigated after it is magnified You can further magnify the picture while searching for details Selecting the aspect ratio The aspect ratio is the ratio of the image width to the image height Most analog TV and some computers are in 4 3 ratio and digital TV and DVDs are usually in 16 9 ratio With the advent of digital signal processing digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal To change the projected picture ratio no matter what aspect the source is Using the remote control Press ASPECT to show the current setting Operation 29 2 Press ASPECT repeatedly to select an aspect ratio to suit the format of the video signal and your display requirements Using the OSD menu Press MENU EXIT and then press 4 gt until the DISPLAY menu is highlighted Press W to highlight Aspect Ratio 3 Press lt to select an aspect ratio to suit the format of the video signal and your display requirements M 30 Operation About the aspect ratio C n the pictures below the black portions are inactive areas and the white portions are active areas OSD menus can be displayed on those unused black areas l Auto Scales an image proportionally to fit the projector s native resolu
21. want you to have a pleasant experience using your BenQ projector so we need to bring this safety matter to your attention to prevent possible damage to person and property If you intend to mount your projector on the ceiling we strongly recommend that you use a proper fitting BenQ projector ceiling mount kit and that you ensure it is securely and safely installed If you use a non BenQ brand projector ceiling mount kit there is a safety risk that the projector may fall from the ceiling due to an improper attachment through the use of the wrong gauge or length screws You can purchase a BenQ projector ceiling mount kit from the place you purchased your BenQ projector BenQ recommends that you also purchase a separate Kensington lock compatible security cable and attach it securely to both the Kensington lock slot on the projector and the base of the ceiling mount bracket This will perform the secondary role of restraining the projector should its attachment to the mounting bracket become loose Hg Lamp contains mercury Manage in A accordance with local disposal laws See www lamprecycle org Important safety instructions Introduction Projector features The projector offers the following features SmartEco starts your dynamic power saving The SmartEco technology offers a new way of operating the projector lamp system and saves lamp power depending on the content brightness level Longest lamp life with
22. will restart whenever the Timer Period is reset 3 Press W to highlight Timer Display and choose if you want the timer to show up on the screen by pressing lt gt Selection Description Always Displays the timer on screen throughout the presentation time 3 min 2 min min Displays the timer on screen in the last 3 2 1 minute s Never Hides the timer throughout the presentation time Operation 35 4 Press V to highlight Timer Position and set the timer position by pressing lt gt Top Left Bottom Left gt Top Right Bottom Right 5 Press V to highlight Timer Counting Direction and select your desired counting direction by pressing lt gt Selection Description Count Up Increases from 0 to the preset time Count Down Decreases from the preset time to 0 6 Press V to highlight Sound Reminder and decide if you want to activate sound reminder by pressing lt gt If you select On a double beep sound will be heard at the last 30 seconds of counting down up and a triple beep sound will be produced when the timer is up 7 activate the presentation timer press W and press lt gt to highlight On and pres MODE ENTER 8 confirmation message displays Highlight Yes and press MODE ENTER on the projector or remote control to confirm You will see the message Timer is On displaying on the screen The timer starts counting when the timer is on To cancel
23. 2 795 106 500 1280 x 800 WXGA_ 85 84 880 71 554 122 500 WXGA 120 Reduce Blanking 119 909 101 563 146 25 SXGA_60 60 020 63 981 108 000 1280 x 1024 SXGA_75 75 025 79 976 135 000 SXGA_85 85 024 91 146 157 500 1280 x 960_60 60 000 60 000 108 1280 960 1280 x 960_85 85 002 85 938 148 500 1360 x 768 1360 x 768_60 60 015 47 712 85 500 1440 x 900 WXGA _60 59 887 55 935 106 500 1400 x 1050 SXGA _60 59 978 65 317 121 750 1600 x 1200 UXGA 60 000 75 000 162 000 640 x 480 67Hz MAC13 66 667 35 000 30 240 832 x 624 75Hz 16 74 546 49 722 57 280 1024 x 768 75Hz MAC19 75 020 60 241 80 000 1152 x 870 75Hz MAC21 75 06 68 68 100 00 Po Supported timing for 3D signal in Frame Sequential Top Bottom and Side by Side formats Supported timing for 3D signal in Frame Sequential format Supported timing for 3D signal Top Bottom and Side by Side formats The timings showing above may not be supported due to EDID file and VGA graphic card limitations It is possible that some timings cannot be chosen 64 Specifications Vertical Horizontal Pixel Timing Resolution Frequency Frequency Frequency Remark Hz kHz MHz 480i 720 x 480 59 94 15 73 27 HDMI only 480p 720 x 480 59 94 31 47 27 HDMI only 576i 720 x 576 50 15 63 27 HDMI DVI 576p 720 x 576 50 31 25 27 HDMI DVI 720 50p 1280 x 720 50 37 5 74 25 HDMI DVI 720 60p 1280 x 720 60 45 00 74 25 HD
24. 3908 4418 175 140 3556 3015 1885 3660 4209 4758 188 150 3810 3231 2019 3922 4510 5098 202 160 4064 3446 2154 4183 4810 5438 215 170 4318 3662 2289 4444 5111 5778 229 For example if you are using 120 screen the recommended projection distance is 3608 mm and the vertical offset is 162 mm If your measured projection distance is 4 5 m 4500 mm the closest match in the Projection distance mm column is 4510 mm Looking across this row shows that a 150 about 3 8 m screen is required C All measurements are approximate and may vary from the actual sizes BenQ recommends that if you intend to permanently install the projector you should physically test the projection size and distance using the actual projector in situ before you permanently install it so as to make allowance for this projector s optical characteristics This will help you determine the exact mounting position so that it best suits your installation location Positioning your projector Connection When connecting a signal source to the projector be sure to 2 3 Turn all equipment off before making any connections Use the correct signal cables for each source Ensure the cables are firmly inserted In the connections shown below some cables may not be included with the projector see Shipping contents on page 8 They are commercially available from electronics stores The connection illustrations below are for
25. 5 Audio signal output PC audio jack x 1 Control RS 232 serial control 9pin x 1 LAN control RJ45 x 1 IR receiver x 2 Input terminals Computer input RGB input D Sub 15 pin female x 2 Video signal input S VIDEO Mini DIN 4 pin port x 1 VIDEO RCA jack x 1 SD HDTV signal input Analog Component RCA jack x 3 through RGB input Digital HDMI MHL x 1 MX666 Digital HDMI x 1 MW665 Audio signal input Audio in RCA audio jack L R x 2 PC audio jack x 1 USB port Type A x 1 Mini B x 1 Environmental Requirements Operating temperature 0 40 at sea level Operating relative humidity 1096 9096 without condensation Operating altitude 0 1499 m at 0 C 35 C 1500 3000 m at 0 C 30 C with High Altitude Mode on Specifications 61 62 Dimensions 311 8 mm W x 104 07 mm H x 244 1 mm D Qv genio Unit mm Ceiling mount installation Ceiling Mount screw M4 Max L 25 mm Min L 20 mm jl r e Unit mm Specifications Timing chart Supported timing for PC input Vertical Horizontal Pixel Resolution Mode Frequency Frequency Frequency Hz kHz MHz VGA_60 59 940 31 469 25 175 VGA_72 72 809 37
26. 626 1219 2462 2831 3200 91 90 2286 1829 1372 2769 3185 3600 103 100 2540 2032 1524 3077 3538 4000 114 120 3048 2438 1829 3692 4246 4800 137 155 3937 3150 2362 4769 5485 6200 177 200 5080 4064 3048 6154 7077 8000 229 250 6350 5080 3810 7692 8846 10000 286 300 7620 6096 4572 9231 10615 12000 343 For example if you are using an 120 inch screen the recommended projection distance is 4246 mm and the vertical offset is 137 mm If your measured projection distance is 5 5 m 5500 mm the closest match in the Projection distance mm column is 5485 mm Looking across this row shows that a 155 about 3 9 m screen is required Positioning your projector 17 18 MW665 16 10 Screen diagonal Screen Center of lens The screen aspect ratio is 16 10 and the projected picture is in a 16 10 aspect ratio Screen size Projection distance mm Diagonal Min Vertical w H distance Average distance offset ee mm mm max min mm zoom zoom 60 1524 1292 808 1569 1804 2039 81 70 1778 1508 942 1830 2105 2379 94 80 2032 1723 1077 2092 2405 2719 108 90 2286 1939 1212 2353 2706 3059 121 100 2540 2154 1346 2614 3007 3399 135 110 2794 2369 1481 2876 3307 3739 148 120 3048 2585 1615 3137 3608 4078 162 130 3302 2800 1750 3399
27. 861 31 500 VGA_75 75 000 37 500 31 500 VGA_85 85 008 43 269 36 000 720 x 400 720 x 400_70 70 087 31 469 28 3221 SVGA_60 60 317 37 879 40 000 SVGA_72 72 188 48 077 50 000 SVGA_75 75 000 46 875 49 500 209 X699 SVGA_85 85 061 53 674 56 250 SVGA 120 Reduce Blanking 119854 77 425 83 000 XGA_60 60 004 48 363 65 000 XGA_70 70 069 56 476 75 000 a XGA 75 75 029 60 023 78 750 924 168 _85 84 997 68 667 94 500 XGA 120 Reduce Blanking 119 989 97 551 115 5 1152 x 864 1152 x 864_75 75 67 5 108 4 BenQ 024 x 576 Notebook timing 60 0 35 820 46 966 1024 x 600 Mo 64 995 41 467 51 419 Notebook timing 1280 x 720 1280 x 720 60 60 45 000 74 250 1280 x 768 1280 x 768 60 59 87 47 776 79 5 WXGA_60 59 810 49 702 83 500 WXGA_75 74 934 62 795 106 500 1280 x 800 WXGA_85 84 880 71 554 122 500 WXGA 120 Reduce Blanking 119 909 101 563 146 25 SXGA_60 60 020 63 981 108 000 1280 x 1024 SXGA_75 75 025 79 976 135 000 SXGA_85 85 024 91 146 157 500 1280 x 960_60 60 000 60 000 108 000 1280590 1280 x 960_85 85 002 85 938 148 500 1360 x 768 1360 x 768_60 60 015 47 712 85 5 1440 x 900 WXGA _60 59 887 55 935 106 500 1400 x 1050 SXGA _60 59 978 65 317 121 750 1600 x 1200 UXGA 60 000 75 000 162 000 640 x 480 67Hz MAC13 66 667 35 000 30 240 832 x 624 75Hz MAC16 74 546 49 722 57 280 1024 x 768 75Hz MAC19 74 93 60 241 80 000 1152 x 870 75Hz MAC21 75 060 68 680 100 000 Supported timing for 3D signal in Top Bottom and Side by Sid
28. BenQ s only obligation and your exclusive remedy shall be replacement of any defective parts labor included To obtain warranty service immediately notify the dealer from which you purchased the product of any defects Important The above warranty shall be void if the customer fails to operate the product in accordance with BenQ s written instructions especially the ambient humidity must be in between 10 and 90 temperature in between 0 C and 35 altitude lower than 4920 feet and avoiding to operate the projector in a dusty environment This warranty gives you specific legal rights and you may have other rights which vary from country to country For other information please visit www BenQ com Copyright Copyright 2013 by BenQ Corporation All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of BenQ Corporation Disclaimer BenQ Corporation makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties merchantability or fitness for any particular purpose Further BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof w
29. D menu system Press MODE ENTER The message INPUT PASSWORD displays Enter the current password i If the password is correct the OSD menu returns to the Security Settings page Press W to highlight Power On Lock and press lt gt to select Off You will not have to enter the password next time when turning on the projector Press Y to highlight Web Control Lock and press lt to select Off Now the Web Control Lock is released and projector settings can be changed via the Projector Network Display System ii If the password is incorrect the password error message displays lasting for three seconds and the message INPUT PASSWORD displays for your retry You can press MENU EXIT to cancel the change or try another password C Though the password function is disabled you need to keep the old password in hand should you ever need to re activate the password function by entering the old password Switching input signal The projector can be connected to multiple devices at the same time However it can only display one full screen at a time When starting up the projector automatically searches for the available signals Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals To select the source l Press SOURCE on the projector or remote control source selection displays 2 Press until your desired signal is
30. Fine Tuning and press MODE ENTER The Color Temperature Fine Tuning page displays 3 Press A V to highlight the item you want to change and adjust the values by pressing lt p gt R Gain G Gain B Gain Adjusts the contrast levels of Red Green and Blue R Offset G Offset B Offset Adjusts the brightness levels of Red Green and Blue 4 Press MENU EXIT to exit and save the settings 3D Color Management In most installation situations color management will not be necessary such as in classroom meeting room or lounge room situations where lights remain on or where building external windows allow daylight into the room Only in permanent installations with controlled lighting levels such as boardrooms lecture theaters or home theaters should color management be considered Color management provides fine color control adjustment to allow for more accurate color reproduction should you require it Proper color management can only be achieved under controlled and reproducible viewing conditions You will need to use a colorimeter color light meter and provide a set of suitable source images to measure color reproduction These tools are not provided with the projector however your projector supplier should be able to provide you with suitable guidance or even an experienced professional installer The Color Management provides six sets RGBCMY of colors to be adjusted When you select each color you can independently ad
31. MI DVI 1080 50i 1920 x 1080 50 28 13 74 25 HDMI DVI 1080 60i 1920 x 1080 60 33 75 74 25 HDMI DVI 1080 24P 1920 x 1080 24 27 74 25 HDMI DVI 1080 25P 1920 x 1080 25 28 13 74 25 HDMI DVI 1080 30P 1920 x 1080 30 33 75 74 25 HDMI DVI 1080 50P 1920 x 1080 50 56 25 148 5 HDMI DVI 1080 60P 71920 x 1080 60 67 5 148 5 HDMI DVI C Supported timing for 3D signal in Frame Sequential format Supported timing for 3D signal in Top Bottom Frame Packing and Side by Side formats Supported timing for 3D signal in Frame Sequential Top Bottom Frame Packing and Side by Side formats Supported timing for 3D signal in Side by Side format Supported timing for 3D signal in Top Bottom format Supported timing for MHL input MX666 Vertical Horizontal Pixel Timing Resolution Frequency Frequency Frequency Remark Hz kHz MHz 480i 720 1440 x 480 59 94 15 73 27 MHL 480p 720 x 480 59 94 31 47 27 MHL 576i 720 1440 x 576 50 15 63 27 MHL 576p 720 x 576 50 31 25 27 MHL 720 50p 1280 x 720 50 37 5 74 25 MHL 720 60p 1280 x 720 60 45 00 74 25 MHL 1080 50i 1920 x 1080 50 28 13 74 25 MHL 1080 60i 1920 x 1080 60 33 75 74 25 MHL 1080 24P 1920 x 1080 24 27 74 25 MHL 1080 25P 1920 x 1080 25 28 13 74 25 MHL 1080 30P 1920 x 1080 30 33 75 74 25 MHL Specifications 65 66 Supported timing for Component YPbPr input
32. Off Monitor Out On Off MX666 Off Audio In Audio L R Standby pe ee Display USB Settings Audio Pass Through MW 665 Off Audio In Audio L R HDMI Network Display USB Display MHL Charging MX666 On Off Operation Main menu Sub menu Options Status DHCP IP Address Wired LAN Subnet Mask Default Gateway DNS Server Apply Status 5 SSID SYSTEM oe Wireless LAN SS D Display SETUP ettings IP Address Connection Mode Advanced PPY Remote Desktop C Log In On Off Broadcasting Device On Off Discovery MAC Address Reset All Settings Source Picture Mode 6 Lamp Mode INFORMA Current System Status TION Resolution 3D Format Color System Equivalent Lamp Hour Firmware Version 7 USB Slideshow On Off READER Slideshow Direction Slide Right Slide Left Slide Up Slide ilable avai 3 sec 4 sec 5 sec Slideshow Timing only when a Repeat Slideshow On Off USB flash Auto Rotation On Off drive is detected Best Fit On Off Note that the menu items are available when the projector detects at least one valid signal If there is no equipment connected to the projector or no signal detected limited menu items are accessible Operation 45 Description of each menu Function Description nu uu 1 Wall Color Corrects the projected picture s color when the projection
33. Refer servicing to qualified service personnel Always open the lens shutter if any or remove the lens cap if any when the projector lamp is sp cd In some countries the line voltage is NOT stable This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC but could fail if power cuts or surges of 10 volts occur In areas where the mains voltage may fluctuate or cut out it is recommended that you connect your projector through a power stabilizer surge protector or uninterruptible power supply UPS Do not block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire To temporarily turn off the lamp press ECO BLANK on the projector or remote control Important safety instructions 3 4 Safety Instructions Continued 8 Do not operate lamps beyond the rated lamp life Excessive operation of lamps beyond the rated life could cause them to break on rare occasions 9 Never replace the lamp assembly or any electronic components unless the projector is unplugged 7 The lamp becomes extremely hot 10 during operation Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement 12 Do not place this product on an unstable cart stand or table The product may fall sustain
34. a normal 90 second duration to approximately 15 seconds This function is only available when Instant Restart is off Cr Instant Restart Selecting On enables you to restart the projector immediately within 90 seconds after turning it off Blank Timer Sets the image blank time when the Blank feature is activated once elapsed the image will return to the screen See Hiding the image on page 37 for details Sleep Timer Sets the auto shutdown timer Operation 49 Function Description A Remote Allows you to enable all the remote receivers or one specific remote Receiver receiver on the projector lt 4 Panel Key Disables or enables all panel key functions except POWER on the m Lock projector and keys on the remote control See Locking control keys x on page 37 for details V Background m E Sets the background color for the projector c ay 00 b a Splash Allows you to select which logo screen will display during projector 3 Screen start up 5 uw High Altitude A mode for operation in high altitude areas See Operating in a high altitude environment on page 37 for details Mode m Audio lt Settings See Adjusting the sound on page 38 for details Lamp Mode Cc See Setting the Lamp Mode on page 54 for details Lamp Reset Lamp Timer See Resetting the lamp timer on page 58 for details Settings Equivalent Lamp Hour See Getting to know the l
35. amp hour page 54 for details how the total lamp hour is calculated 3 Securit g Segs See Utilizing the password function on page 26 for details 50 Operation dNLAS WALSAS S pa ueApy Function Description Selects a baud rate that is identical with your computer s so that you Baud Rate can connect the projector using a suitable RS 232 cable and update or download the projector s firmware This function is intended for qualified service personnel Test Pattern See Using the test pattern on page 38 for details Closed Caption Closed Caption Enable Activates the function by selecting On when the selected input signal carries closed captions e Captions An on screen display of the dialogue narration and sound effects of TV programs and videos that are closed captioned usually marked as CC in TV listings Caption Version Selects a preferred closed captioning mode To view captions select CCI CC2 CC3 or CC4 CCI displays captions in the primary language in your area Standby Settings Network Selecting On enables the function The projector is able to provide the network function when it is in standby mode Monitor Out Selecting On enables the function The projector can output a VGA signal when it is in standby mode and the COMPUTER 1 jack is correctly connected to devices See Connection on page 19 for how to make the connection Audio Pass
36. anel key lock use the remote control to enter the SYSTEM SETUP Basic gt Panel Key Lock menu and press 4 gt to select Off C3 Keys on the remote control still active when panel key lock is enabled Ifyou turn off the projector without disabling panel key lock the projector will still be in locked status the next time it is turned on Operating in a high altitude environment We recommend you use the High Altitude Mode when your environment is between 1500 m 3000 m above sea level and ambient temperature is between 0 30 Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and ambient temperature is between 0 and 35 C The projector will be over cooled if you turn the mode on under such a condition To activate the High Altitude Mode Press MENU EXIT and then press lt gt until the SYSTEM SETUP Advanced menu is highlighted 2 Press V to highlight High Altitude Mode and press lt gt select On A confirmation message displays 3 Highlight Yes and press MODE ENTER Operation under High Altitude Mode may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance If you use this projector under other extreme conditions excluding the above it may display auto shut down symptoms which is designed to protect your projector from over heating In cases like this you should switch to H
37. automatically chooses an appropriate 3D format when detecting 3D contents If the projector cannot recognize the 3D format press A W to choose a 3D mode Cr When the 3D function is on The brightness level of the projected image will decrease The following settings cannot be adjusted Picture Mode Reference Mode The 2D Keystone can only be adjusted within limited degrees 3D Sync Invert When you discover the inversion of the image depth enable this function to correct the problem Apply 3D Settings After the 3D settings are saved you can decide if you would like to apply them by choosing a set of 3D settings that you have saved Once applied the projector will automatically play the incoming 3D contents if it matches the 3D settings saved CT Only the set s of 3D settings with memorized data is available Save 3D Settings When you have successfully displayed the 3D contents after making the appropriate adjustments you can enable this function and choose a set of 3D settings to memorize current 3D settings Teaching Template See Using the teaching templates on page 39 for details Operation 47 Function Description Picture Mode Pre defined picture modes are provided so you can optimize your projector image set up to suit your program type See Selecting a picture mode on page 32 for details Selects a picture mode that best suits your need for the image quality
38. cation with the projector placed on the table behind the screen Note that a special rear projection screen is required Set Rear Table in the SYSTEM SETUP Basic gt Projector Installation menu after you turn the projector on DEED Your room layout or personal preference will dictate which installation location you select Take into consideration the size and position of your screen the location of a suitable power outlet as well as the location and distance between the projector and the rest of your equipment Positioning your projector Obtaining preferred projected image size The distance from the projector lens to the screen the zoom setting and the video format each factors in the projected image size Projection dimensions Refer to Dimensions on page 62 for the center of lens dimensions of this projector before calculating the appropriate position MX666 4 3 Screen diagonal 7 Screen Center of lens Vertical offset 18 Projection distance The screen aspect ratio is 4 3 and the projected picture is in a 4 3 aspect ratio Screen size Projection distance mm Diagonal Vertical w H distance Average distance offset K mm mm max min mm zoom zoom 50 1270 1016 762 1538 1769 2000 57 60 1524 1219 914 1846 2123 2400 69 70 1778 1422 1067 2154 2477 2800 80 80 2032 1
39. cus of the lens using the focus ring The projector and the screen are not aligned properly Adjust the projection angle and direction as well as the height of the projector if necessary The lens cover is still closed Open the lens cover Remote control does not work Cause Remedy The battery is out of power Replace the battery with new ones There is an obstacle between the remote control and the projector Remove the obstacle You are too far away from the projector Stand within 8 meters 26 feet of the projector The password is incorrect Cause Remedy You do not remember the password Please see Entering the password recall procedure on page 27 for details Troubleshooting Specifications Projector specifications All specifications are subject to change without notice Optical Resolution 1024 x 768 XGA MX666 1280 x 800 WXGA MW665 Display system 1 CHIP DMD Lens F Number F 2 59 2 87 f 16 88 21 88 mm Lamp 240 W lamp MX666 210 W lamp MW665 Electrical Power supply AC100 240V 3 5 A 50 60 Hz Automatic Power consumption 353 W lt 0 5 W Standby MX666 322 W Max lt 0 5 W Standby MW665 Mechanical Weight 2 75 Kg 6 06 Ibs MX666 2 8 Kg 6 17 Ibs MW665 Output terminals RGB output D Sub 15 pin female x 1 Speaker Stereo 10 watt x 1 MX666 Stereo 2 watt x 1 MW66
40. d result in malfunction Do not over tighten the screw 10 Replace the lamp cover on the projector ll Tighten the screw that secures the lamp cover A Loose screw may cause a bad connection which could result in malfunction Do not over tighten the screw 12 Connect the power and restart the projector A Do not turn the power on with the lamp cover removed Maintenance 57 Resetting the lamp timer 13 After the startup logo open the On Screen Display OSD menu Go to the SYSTEM SETUP Advanced gt Lamp Settings menu Press MODE ENTER The Lamp Settings page displays Highlight Reset Lamp Timer A warning message displays asking if you want to reset the lamp timer Highlight Reset and press MODE ENTER The lamp time will be reset to 0 A Do not reset if the lamp is not new or replaced as this could cause damage 58 Maintenance Indicators Light Status amp Description POWER TEMP LAMP Power events Orange Off Off Stand by mode Green Flashing Off Off Powering up Green Off Off Normal operation Orange Flashing Off Off Normal power down cooling Red Off Off Download Green Off Red CW start fail Red Flashing Off Off Scaler shutdown fail data abort Red Off Red Scaler reset fail video projector only Lamp events Off Off Red Lamp error in normal operation Orange Off Off Flashing Lamp is not lit up Therma
41. devices have active audio output you will still hear the audio even though the image is frozen onscreen 36 Operation Hiding the image In order to draw the audience s full attention to the presenter you can use ECO BLANK on the projector or remote control to hide the screen image When this function is activated with an audio input connected the audio can still be heard You can set the blank time in the SYSTEM SETUP Basic gt Operation Settings gt Blank Timer menu to let the projector return the image automatically after a period of time when there is no action taken on the blank screen If the preset time spans are not suitable for your presentation select Disable No matter Blank Timer is activated or not you can press most of the keys on the projector or remote control to restore the picture Do not block the projection lens from projecting as this could cause the blocking object to become heated and deformed or even cause a fire Locking control keys With the control keys on the projector locked you can prevent your projector settings from being changed accidentally by children for example When the Panel Key Lock is on no control keys on the projector will operate except POWER 1 Goto the SYSTEM SETUP Basic gt Panel Key Lock menu and select On by pressing lt gt on the projector or remote control A confirmation message displays 2 Highlight Yes and press MODE ENTER to confirm To release p
42. displayed I Plug the USB flash drive into the USB TYPE A jack of the projector 2 The projector automatically displays the detected USB flash drive Or you can manually select USB Reader from the source selection bar 3 Found USB disc icon s will appear on the lower left corner Press A W lt to select the desired disc drive and press MODE ENTER 4 Thumbnails of the files stored on the USB flash drive will display When viewing thumbnails To Press scroll through thumbnails lt open the folder or view image MODE ENTER document file in full screen return to an upper directory MODE ENTER when the Back icon is selected change to a different page 4 5 To exit full screen mode press MODE ENTER Operation Shutting down the projector Press D POWER OFF and a confirmation message will display prompting you If you don t respond in a few seconds the message will disappear 2 Press 0 POWER or OFF a second time The POWER indicator light flashes orange the projection lamp shuts down and the fans will continue to run for approximately 90 seconds to cool down the projector A To protect the lamp the projector will not respond to any commands during the cooling process To shorten the cooling time you can also activate the Quick cooling function See Quick Cooling on page 49 for details 3 Once the cooling process finishes a Power Off Ring Tone will be heard
43. e formats Supported timing for 3D signal in Frame Sequential Top Bottom and Side by Side formats Supported timing for 3D signal in Frame Sequential format The timings showing above may not be supported due to EDID file and VGA graphic card limitations It is possible that some timings cannot be chosen Specifications 63 Supported timing for HDMI HDCP input Vertical Horizontal Pixel Resolution Mode Frequency Frequency Frequency Hz kHz MHz _60 59 940 31 469 25 175 _72 72 809 37 861 31 500 nee VGA_75 75 000 37 500 31 500 VGA_85 85 008 43 269 36 000 720 x 400 720 x 400_70 70 087 31 469 28 3221 SVGA_60 60 317 37 879 40 000 SVGA_72 72 188 48 077 50 000 SVGA_75 75 000 46 875 49 500 SUD OCRUM SVGA 85 85 061 53 674 56 250 SVGA 120 Reduce Blanking 119 854 77 425 83 000 XGA_60 60 004 48 363 65 000 XGA_70 70 069 56 476 75 000 XGA_75 75 029 60 023 78 750 1024x768 XGA_85 84 997 68 667 94 500 XGA_120 Reduce Blanking 119 989 97 551 115 5 1152 x 864 1152 x 864 75 75 67 5 108 1280 x 768 1280 x 768 60 59 87 47 776 79 5 1024 x 576 60Hz BENG Notebook 60 00 35 820 46 996 Timing 1024 x 600 65Hz Notebook 64 995 41 467 51 419 Timing 1280 x 720 1280 x 720_60 60 45 000 74 250 1280 x 768 1280 x 768_60 59 870 47 776 79 5 WXGA_60 59 810 49 702 83 500 WXGA 75 74 934 6
44. enzene thinner or other chemical detergents These can damage the case Storing the projector If you need to store the projector for an extended time please follow the instructions below Make sure the temperature and humidity of the storage area are within the recommended range for the projector Please refer to Specifications on page 61 consult your dealer about the range e Retract the adjuster feet e Remove the battery from the remote control e Pack the projector in its original packing or equivalent Transporting the projector It is recommended that you ship the projector with its original packing or equivalent Maintenance 53 54 information Getting to know the lamp hour When the projector is in operation the duration in hours of lamp usage is automatically calculated by the built in timer To obtain the lamp hour information I Press MENU EXIT and then press lt P gt to highlight the SYSTEM SETUP Advanced menu 2 Press Y to highlight Lamp Settings and press MODE ENTER The Lamp Settings page displays 3 You will see the Equivalent Lamp Hour information displaying on the menu 4 To leave the menu press MENU EXIT You can also get the lamp hour information on the INFORMATION menu Extending lamp life The projection lamp is a consumable item that normally can last up to 3000 4000 hours with proper usage To keep the lamp life as long as possible you can do the following settings
45. ess MODE ENTER to dismiss the message Out of Lamp Usage Time Replace lamp Refer to user manual Then reset lamp timer Order a new lamp at lamp benq com Q XXXX shown in the above messages are numbers that vary depending on different models Maintenance 55 Replacing the lamp A Toreduce the risk of electrical shock always turn the projector off and disconnect the power cord before changing the lamp To reduce the risk of severe burns allow the projector to cool for at least 45 minutes before replacing the lamp To reduce the risk of injuries to fingers and damage to internal components use caution when removing lamp glass that has shattered into sharp pieces To reduce the risk of injuries to fingers and or compromising image quality by touching the lens do not touch the empty lamp compartment when the lamp is removed This lamp contains mercury Consult your local hazardous waste regulations to dispose of this lamp in a proper manner assure optimal performance from the projector it is recommended that you purchase a qualified projector lamp for lamp replacement If lamp replacement is performed while the projector is suspended upside down from the ceiling make sure that no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes caused by fractured lamp Ensure good ventilation when handling broken lamps We recommend that you use respirato
46. ess V to correct keystoning at the bottom of the image For the MW665 you can also press D on the projector to correct keystoning at the right side of the image Press on the projector to correct keystoning at the left side of the image Using the OSD menu l Press MENU EXIT and then press lt P gt until the DISPLAY menu is highlighted 2 Press V to highlight 2D Keystone and press MODE ENTER The 2D Keystone correction page displays 3 Press to correct keystoning at the top of the image Press V 7 to correct keystoning at the bottom of the image Press on the projector to correct keystoning at the right side of the image Press on the projector to correct keystoning at the left side of the image Operation Using the menus The projector is equipped with On Screen Display OSD menus for making various adjustments and settings The OSD screenshots below are for reference only and may differ from the actual design Below is the overview of the OSD menu Main menu icon Wall Color Aspect Ratio 2D Keystone Position Status Sub menu Press MENU Teaching Template EXIT to the previous Highlight page or to Current input signal Analog RGB MENU Exit exit The following example describes how to set the OSD language l Press MENU EXIT on the projector or 3 Press W to highlight Language remote control to turn the OSD menu on and press MODE ENTER Pre
47. guage English Hrvatski nska Romana jerlands Norsk T rk e Dansk tina Portugu s suomi Ins Indonesian Polski EMnvik Press Enter to Confirm Exit to leave If the frequency resolution of the input signal exceeds the projector s operating range you will see the message Out of Range displayed on the background screen Please change to an input signal which is compatible with the projector s resolution or set the input signal to a lower setting See Timing chart on page 63 for details If no signal is detected for 3 minutes the projector automatically enters ECO BLANK mode Operation Adjusting the projected image Adjusting the projection angle The projector is equipped with quick release adjuster foot and rear adjuster foot These adjusters change the image height and projection angle To adjust the projector l Press the quick release button and lift the front of the projector Once the image is positioned where you want it release the quick release button to lock the foot in position 2 Screw the rear adjuster foot to fine tune the horizontal angle To retract the foot hold up the projector while pressing the quick release button then slowly lower the projector Screw the rear adjuster foot in a reverse direction Do not look into the lens while the A lamp is on The strong light from the lamp may cause damage to your e
48. he method you choose will most likely depend upon the availability of matching terminals on both the projector and the video source device as described below Terminal name Terminal appearance Picture quality HDMI MHL MX666 HDMI MW665 o Best Component Video Better S Video Good Video O Normal Connecting audio The projector has built in mono speaker s which are designed to provide basic audio functionality accompanying data presentations for business purposes only They are not designed for nor intended for stereo audio reproduction use as might be expected in home theater or home cinema applications Any stereo audio input if provided is mixed into a common mono audio output through the projector speaker s The built in speaker s will be muted when the AUDIO OUT jack is connected 37 The projector is only capable of playing mixed mono audio even if a stereo audio input is connected See Connecting audio on page 20 for details Connection If the selected video image is not displayed after the projector is turned on and the correct video source has been selected check that the video source device is turned on and operating correctly Also check that the signal cables have been connected correctly Connecting smart devices MX666 The projector can project the content directly from a MHL compatible smart device Using a HDMI to Micro USB cable or a HDMI
49. igh Altitude mode to solve these Operation 37 symptoms However this is not to state that this projector can operate under and all harsh or extreme conditions Adjusting the sound The sound adjustments made as below will have an effect on the projector speaker s Be sure you have made a correct connection to the projector audio input See Connection on page 19 for how the audio input is connected Muting the sound To temporarily turn off the sound I Press MENU EXIT and then press lt gt until the SYSTEM SETUP Advanced menu is highlighted 2 Press V to highlight Audio Settings and press MODE ENTER The Audio Settings page displays 3 Highlight Mute and press lt P gt to select On C If available you can also press MUTE on the remote control to toggle projector audio between on and off Adjusting the sound level To adjust the sound level press 16 or I Repeat steps l 2 above 2 Press V to highlight Volume and press lt to select a desired sound level Turning off the Power On Off Ring Tone To turn off the ring tone I Repeat steps l 2 above 2 Press Y to highlight Power On Off Ring Tone and press lt gt to select Off C The only way to change Power On Off Ring Tone is setting On or Off here Setting the sound mute or changing the sound level will not affect the Power On Off Ring Tone Using the test pattern The projector is able to display the grid test pattern It helps yo
50. ing serious damage Do not attempt to disassemble this projector There are dangerous high voltages inside which may cause death if you should come into contact with live parts The only user serviceable part is the lamp which has its own removable cover Under no circumstances should you ever undo or remove any other covers Refer servicing only to suitably qualified professional service personnel When the projector is under operation you may sense some heated air and odor from its ventilation grill It is a normal phenomenon and not a product defect Important safety instructions Safety Instructions Continued 13 Do not place this projector in any of the following environments Space that is poorly ventilated or confined Allow at least 50 cm clearance from walls and free flow of air around the projector Locations where temperatures may become excessively high such as the inside of a car with all windows rolled up Locations where excessive humidity dust or cigarette smoke may contaminate optical components shorten the projector s life span and darken the image Locations near fire alarms Locations with an ambient temperature above 40 104 F Locations where the altitudes are higher than 3000 m 10000 feet 3000 m Do not block the ventilation holes Do not place this projector on a blanket bedding or any other soft surface Do not cover this p
51. ithout obligation to notify any person of such revision or changes DLP Digital Micromirror Device and are trademarks of Texas Instruments Others are copyrights of their respective companies or organizations Patents This BenQ projector is covered by the following patents U S patents 6 837 608 7 275 834 7 181 318 TW patents 202690 205470 1228635 1259932 China patents 18811 ZLOI 143168 7 2103119907 0 ZL200510051609 2 Warranty and Copyright information 67
52. just its range and saturation according to your preference If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monitors TVs projectors etc you can project any image from the disc on the screen and enter the 3D Color Management menu to make adjustments To adjust the settings l Go to the PICTURE menu and highlight 3D Color Management 2 Press MODE ENTER on the projector or remote control and the 3D Color Management page displays 3 Highlight Primary Color and press lt to select a color from among Red Yellow Green Cyan Blue or Magenta 4 Press V to highlight Hue and press 4 gt to select its range Increase in the range will include colors consisted of more proportions of its two adjacent colors Operation Please refer to the illustration to the right for how the colors relate to each other For example if you select Red and set its range at 0 only pure red in the projected picture will be selected Increasing its range will include red close to yellow and red close to magenta Press W to highlight Saturation and adjust its values to your preference by pressing 4 p gt Every adjustment made will reflect to the image immediately For example if you select Red and set its value at 0 only the saturation of pure red will be affected Saturation is the amount of that color in a video picture Lower settings produce less saturated c
53. k Suomi Indonesian EMnvK amp a Redt Projector Installation Front Table Rear Table Rear Ceiling Front Ceiling Menu Display Time 5 10 sec 20 sec 30 sec Always Menu Settings Menu Position Center Top Left Top Right Bottom Right Bottom Left Reminder On Off Message Direct Power On On Off Signal Power On On Off Auto Power Off Disable 3 min 10 15 min 20 min 25 min 30 min Operation Quick Cooling On Off Settings Instant Restart On Off Blank Timer Disable 5 min 10 15 min 20 min 25 min 30 min Sleep Timer Disable 30 min l hr 2 hr 3 hr 4 hr 8 hr 12 hr Remote Receiver Front Top Front Top Panel Key Lock On Off Background Color Black Blue Purple BenQ Splash Screen Black Blue BenQ Operation 43 44 Main menu Sub menu Options High Altitude Mode On Off Mute On Off Audio Volume Settings i ing Power On Off Ring On Off Tone MX666 Normal Economic SmartEco Lamp Lamp Mode MW665 Normal Economic Settings SmartEco LampSave LumenCare 5 SYSTEM SETUP Advanced Reset Lamp Timer Equivalent Lamp Hour Change Password Change Security Power On Lock ettings Settings Web Control Lock Baud Rate 2400 4800 9600 I 9200 38400 57600 115200 Test Pattern On Off Closed Closed Caption Enable On Off Caption Caption Version CCI CC2 CC3 CC4 Network On
54. l events Red Red off Fan error the actual fan speed is outside the desired speed Red Red Flashing off Fan 2 error the actual fan speed is outside the desired speed Red Green off Fan 3 error the actual fan speed is outside the desired speed Red Green off Fan 4 error the actual fan speed is outside the Flashing desired speed Green Red off Temperature error over limited temperature Maintenance 59 Troubleshooting 60 The projector does not turn on Cause Remedy There is no power from the power cord Plug the power cord into the AC power jack on the projector and plug the power cord into the power outlet If the power outlet has a switch make sure that it is switched on Attempting to turn the projector on again during the cooling process Wait until the cooling down process has completed No picture Cause Remedy The video source is not turned on or connected correctly Turn the video source on and check that the signal cable is connected correctly The projector is not correctly connected to the input signal device Check the connection The input signal has not been correctly selected Select the correct input signal with the SOURCE key on the projector or remote control The lens cover is still closed Open the lens cover Blurred image Cause Remedy The projection lens is not correctly focused Adjust the fo
55. mage so that it is O0 O0 oso 9 9 displayed in the center of the screen gt C with a 16 10 aspect ratio This is most suitable for images which already 16 10 picture in a 16 10 aspect as it displays them without aspect alteration Operation 31 32 Optimizing the image Using Wall Color In the situation where you are projecting onto a colored surface such as a painted wall which may not be white the Wall Color feature can help correct the projected picture s colors to prevent possible color difference between the source and projected pictures To use this function go to the DISPLAY gt Wall Color menu and press 4 gt to select a color which is closest to the color of the projection surface There are several precalibrated colors to choose from Light Yellow Pink Light Green Blue and Blackboard Selecting a picture mode The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type To select an operation mode that suits your need you can follow one of the following steps Press MODE ENTER on the projector or remote control repeatedly until your desired mode is selected Goto the PICTURE gt Picture Mode menu and press 4 to select a desired mode I Dynamic mode Maximizes the brightness of the projected image This mode is suitable for environmen
56. menu item 5 Press lt to select a picture mode that is closest to your need Operation 6 Press W to select a menu item to be changed and adjust the value with lt gt See Fine tuning the image quality in user modes below for details Fine tuning the image quality in user modes According to the detected signal type and selected picture mode some of the below functions may not be available Based on your needs you can make adjustments to these functions by highlighting them and pressing on the projector or remote control Adjusting Brightness The higher the value the brighter the image And the lower the setting the darker the image Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible Adjusting Contrast The higher the value the greater the contrast Use this m m to set the white level after have previously A A adjusted the Brightness setting to suit your selected input and viewing environment Adjusting Color Lower setting produces less saturated colors If the setting is too high colors on the image will be overpowering which makes the image unrealistic Adjusting Tint The higher the value the more reddish the picture becomes The lower the value the more greenish the picture becomes Adjusting Sharpness The higher the value the sharper the picture becomes The lower
57. olors a setting of 0 removes that color from the image entirely If the saturation is too high that color will be overpowering and unrealistic 6 7 8 9 Press Y to highlight Gain and adjust its values to your preference by pressing 4 gt The contrast level of the primary color you select will be affected Every adjustment made will reflect to the image immediately Repeat steps 3 to 6 for other color adjustments Make sure you have made all of the desired adjustments Press MENU EXIT to exit and save the settings Resetting current or all picture modes l 2 Go to the PICTURE menu and highlight Reset Picture Settings Press MODE ENTER and press A to select Current or All Current returns current picture mode to the factory preset settings All returns all settings except User I User 2 in the PICTURE menu to the factory preset settings Setting the presentation timer Presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations Follow these steps to utilize this function Go to the SYSTEM SETUP Basic gt Presentation Timer menu and press MODEIENTER to display the Presentation Timer page Highlight Timer Period and decide the time period by pressing lt P gt The length of time can be set from to 5 minutes in minute increments and 5 to 240 minutes in 5 minute increments Cc If the timer is already on the timer
58. om a USB Reader on page 40 for details m USB flash E drive is detected 2 c 52 Operation Maintenance Care of the projector Your projector needs little maintenance The only thing you need to do on a regular basis is to keep the lens and case clean Never remove any parts of the projector except the lamp Contact your dealer if other parts need replacing Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface Please be sure to turn off the projector and let it cool down completely before cleaning the lens Use canister of compressed air to remove dust e If there is dirt or smears use lens cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface Never use any type of abrasive pad alkaline acid cleaner scouring powder or volatile solvent such as alcohol benzene thinner or insecticide Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the projector surface and cabinet material Cleaning the projector case Before you clean the case turn the projector off using the proper shutdown procedure as described in Shutting down the projector on page 41 and unplug the power cord To remove dirt or dust wipe the case with a soft lint free cloth To remove stubborn dirt or stains moisten a soft cloth with water and a neutral pH detergent Then wipe the case A Never use wax alcohol b
59. ore flexible By presenting the depth of the images you can wear BenQ 3D glassed to enjoy the 3D movies videos and sporting events in a more realistic way The apparent brightness of the projected image will vary depending on the ambient lighting conditions selected input signal contrast brightness settings and is directly proportional to projection distance The lamp brightness will decline over time and may vary within the lamp manufacturers specifications This is normal and expected behavior Introduction 7 Shipping contents Carefully unpack and verify that you have all of the items shown below If any of these items are missing please contact your place of purchase Standard accessories C The supplied accessories will be suitable for your region and may differ from those illustrated The warranty card is only supplied in some specific regions Please consult your dealer for detailed information Power cord VGA cable Y iw h Quick start guide User manual CD Warranty card Ji Remote control with batteries Carry bag Optional accessories l Spare lamp kit 3 3D glasses 2 Ceiling mount kit 8 Introduction Projector exterior view Front upper side Rearllower side oo External control panel See Controls and functions on page 10 for details Lamp cover Vent heated air exhaust Quick release button
60. rating in a high altitude environment seeeeee tentent 37 Adjusting the 38 2 Table of contents Using the test pattern 38 Using the teaching templates 39 Presenting from a USB Reader 40 Shutting down the projector 41 Direct power 41 Menu operation 42 Maintenance 53 Care of the projector 53 Lamp information 54 Troubleshooting 60 Specifications 6l Projector specifications 6l Dimensions 62 Ceiling mount installation 62 Timing chart sees 63 Warranty and Copyright information 67 Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment However to ensure safe use of this product it is important that you follow the instructions mentioned in this manual and marked on the product Safety Instructions Please read this manual before You operate your projector Save it for future reference Do not look straight at the projector lens during operation The intense light beam may damage your eyes
61. rning light Lights up red if the projector s temperature becomes too high LAMP indicator light Indicates the status of the lamp Lights up or flashes when the lamp has developed a problem AUTO Automatically determines the best picture timings for the displayed image Keystone Arrow keys U Up 4 Y Down Manually corrects distorted images resulting from an angled projection gt Right 1 Increases the projector volume When the On Screen Display OSD menu is activated the 6 7 14 and 15 keys are used as directional arrows to select the desired menu items and to make adjustments SOURCE Displays the source selection bar Remote control MX666 1JON CS OFF Toggles the projector between standby mode and on Source selection buttons COMPUTER 1 COMPUTER 2 VIDEO S VIDEO HDMI NETWORK Selects an input source for display Keystone Arrow keys U Up al Y Down Manually corrects distorted images resulting from an angled projection MENU EXIT Turns on the On Screen Display OSD menu Goes back to previous OSD menu exits and saves menu settings lt Left if Decreases the projector volume MODE ENTER Selects an available picture setup mode Activates the selected On Screen Display OSD menu item C Te ECO BLANK Used to hide the screen picture LASER Emits visible laser pointer light for presentation purposes MHL control buttons lt lt
62. rojector with a cloth or any other item Do not place inflammables near the projector ev If the ventilation holes are seriously obstructed overheating inside the projector may result in a fire Always place the projector on a level horizontal surface during operation Do not use if tilted at an angle of more than 10 degrees left to right nor at angle of more than 15 degrees front to back Using the projector when it is not fully horizontal may cause a malfunction of or damage to the lamp Do not stand the projector on end vertically Doing so may cause the projector to fall over causing injury or resulting in damage to the projector Important safety instructions 5 6 Safety Instructions Continued 17 Do not step on the projector or place any objects upon it Besides probable physical damage to the projector doing so may result in accidents and possible injury 18 Do not place liquids near or on the projector Liquids spilled into the Projector may cause it to fail If the projector does become wet disconnect it from the power supply s power outlet and call BenQ to have the projector serviced 19 This product is capable of displaying inverted images for ceiling mount installation Use only BenQ s Ceiling Mount Kit for A mounting the projector and ensure it is securely installed 20 This apparatus must be earthed A Ceiling mounting the projector We
63. rs safety glasses goggles or face shield and wear protective clothing such as gloves Turn the power off and disconnect the projector from the power outlet If the lamp is hot avoid burns by waiting for approximately 45 minutes until the lamp has cooled 2 Loosen the screw that secures the lamp cover on the side of the projector until the lamp cover loosens 3 Remove the lamp cover from the projector A Do not turn the power on with the lamp cover removed Do not insert your fingers between the lamp and the projector The sharp edges inside the projector may cause injuries 4 Loosen the screw that secures the lamp Lift the handle so that it stands up 56 Maintenance 6 Use the handle to slowly pull the lamp out of the projector A Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector Do not place the lamp in locations where water might splash on it children can reach it or near flammable materials Do not insert your hands into the projector after the lamp is removed If you touch the optical components inside it could cause color unevenness and distortion of the projected images 7 Asshownin the figure lower the new lamp 8 Tighten the screw that secures the lamp 9 Ensure the handle is fully laid flat and locked in place A Loose screw may cause a bad connection which coul
64. selected Computer2 YPbPr2 and press MODE ENTER Once detected the selected source information HDMI will display at the corner of the screen for seconds If there is multiple equipment connected to the projector repeat steps 1 2 to search for another signal Video S Video C3 The brightness level of the projected image will change accordingly when you switch between different input signals Data graphic PC presentations using mostly static images Network Display are generally brighter than Video using mostly moving images movies USB Display The native display resolution of this projector is in a 4 3 MX666 16 10 MW665 aspect ratio For best display picture results you should select and use an input signal which outputs USB Reader at this resolution Any other resolutions will be scaled by the projector depending upon the aspect ratio setting which may cause some image distortion or loss of picture clarity See Selecting the aspect ratio on page 29 for details Firewall in the PC must be switched off to allow USB Display to work 28 Operation Changing Color Space In the unlikely event that you connect the projector to a DVD player via the projector s HDMI MHL or HDMI input and the projected picture displays wrong colors please change the color space to YUV To do this l Press MENU EXIT and then press lt gt until the SOURCE menu is highlighted 2 Press V to highlight Color Space Con
65. sentation Timer Language Projector Installation Front Table Menu Settings i Operation Settings Remote Receiver Front Top Panel Key Lock Background Color Splash Screen Wall Color Aspect Ratio 2D Keystone Position Phase H Size Digital Zoom 30 3D m Teaching Template 2 Use lt gt to highlight the SYSTEM 4 Press A W lt q to selecta SETUP Basic menu preferred language Exe 5 Press MENU EXIT on the j projector or remote control to Presentationitimer leave and save the settings Language Projector Installation Front Table Menu Settings a Operation Settings Remote Receiver Front Top Panel Key Lock Off Background Color BenQ El Splash Screen BenQ Operation 25 Securing the projector 26 Do not press the numeric buttons when asked to enter the Using a security cable lock The projector has to be installed in a safe place to prevent theft Otherwise purchase a lock such as the Kensington lock to secure the projector You can locate a Kensington lock slot on the rear side of the projector See item 26 on page 9 for details A Kensington security cable lock is usually a combination of key s and the lock Refer to the lock s documentation for finding out how to use it Utilizing the password function For security purposes and to help prevent unauthorized use the projector includes an option for setting up password security The password can be se
66. t through the On Screen Display OSD menu WARNING You will be inconvenienced if you activate the password functionality and subsequently forget the password Print out this manual if necessary and write the password you used in this manual and keep the manual in a safe place for later recall Setting a password C Once a password has been set and the power on lock is activated the projector cannot be used unless the correct password is entered every time the projector is started l Open the OSD menu and go to the SYSTEM SETUP Advanced gt Security Settings menu Press MODE ENTER The Security Settings page displays 2 Highlight Change Security Settings and press MODE ENTER 3 As pictured to the right the four arrow keys INPUT NEW PASSWORD A gt V lt respectively represent 4 digits yum 1 2 3 4 According to the password desire to set press the arrow keys to enter six digits for the password password 4 Confirm the new password by re entering the new password Once the password is set the OSD menu returns to the Security Settings page 5 To activate the Power On Lock function press A W to highlight Power On Lock and press lt P gt to select On 6 To activate the Web Control Lock function press A V to highlight Web Control Lock and press 4 9 to select On When the Web Control Lock function is activated you have to enter the correct password to change projector settings via the Projector Ne
67. the value the softer the picture becomes Adjusting Brilliant Color This feature utilizes a new color processing algorithm and system level enhancements to enable higher brightness while providing truer more vibrant colors in picture It enables a greater than 50 brightness increase in mid tone images which are common in video and natural scenes so the projector reproduces images in realistic and true colors If you prefer images with that quality select On If you don t need it select Off When Off is selected the Color Temperature function is not available Selecting a color temperature The options available for color temperature settings vary according to the signal type selected l Cool Makes images appear bluish white 2 Normal Maintains normal colorings for white 3 Warm Makes images appear reddish white About color temperatures There are many different shades that are considered to be white for various purposes One of the common methods of representing white color is known as the color temperature A white color with a low color temperature appears to be reddish white A white color with a high color temperature appears to have more blue in it Operation 33 34 Setting a preferred color temperature To set a preferred color temperature l Highlight Color Temperature and select Warm Normal or Cool by pressing lt gt on the projector or remote control 2 Press V to highlight Color Temperature
68. tion in its horizontal or vertical width This MX666 MW665 is suitable for the incoming image which is neither in 4 3 nor 16 9 and o o 0 you want to make most use of the O MESS screen without altering the image s 15 9 picture aspect ratio 2 Real The image is projected as its original resolution and resized to fit O gt gt O within the display area For input Q made 4 4 3 picture signals with lower resolutions the projected image will display smaller than if resized to full screen You E could adjust the zoom setting or oo move the towards the 16 9 picture screen to increase the image size if necessary You may also need to refocus the projector after making these adjustments 3 4 3 Scales an image so that it is displayed in the center of the screen gt coy i with a 4 3 aspect ratio This is most suitable for 4 3 images like some 4 3 picture computer monitors standard definition TV and 4 3 aspect DVD movies as it displays them without aspect alteration 4 16 9 Scales an image so that it is displayed in the center of the screen C gt o 9 with 16 9 aspect ratio This is most Le suitable for images which are already 16 9 picture in a 16 9 aspect like high definition TV as it displays them without aspect alteration 5 16 10 Scales an i
69. ts where extra high brightness is required such as using the projector in well lit rooms 2 Presentation mode ls designed for presentations The brightness is emphasized in this mode to match PC and notebook coloring 3 sRGB mode Maximizes the purity of RGB colors to provide true to life images regardless of brightness setting It is most suitable for viewing photos taken with an sRGB compatible and properly calibrated camera and for viewing PC graphic and drawing applications such as AutoCAD 4 Cinema mode ls appropriate for playing colorful movies video clips from digital cameras or DVs through the PC input for best viewing in a blackened little light environment 5 mode ls appropriate for playing 3D images and 3D video clips 6 User I User 2 mode Recalls the settings customized based on the current available picture modes See Setting the User 1 0 2 mode on page 32 for details Setting the User I User 2 mode There are two user definable modes if the current available picture modes are not suitable for your need You can use one of the picture modes except the User 1 2 as a starting point and customize the settings l Press MENU EXIT to open the On Screen Display OSD menu 2 the PICTURE gt Picture Mode menu 3 Press lt P to select User or User 2 4 Press W to highlight Reference Mode Cr This function is only available when User or User 2 mode is selected up in the Picture Mode sub
70. twork Display System IMPORTANT The digits being input will display as asterisks on screen Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it MENU Beck Password Keep this manual in a safe place leave the OSD menu press MENU EXIT Operation If you forget the password If the password function is activated you will be asked to enter the six digit password every time you turn on the projector If you enter the wrong password the password error message as pictured to the right Please y displays lasting for 3 seconds and the INPUT PASSWORD message follows You can retry by entering another six digit password or if you did not record the password in this manual and you absolutely do not remember it you can use the password recall procedure See Entering the password recall procedure on page 27 for details Password Error If you enter an incorrect password 5 times in succession the projector will automatically shut down in a short time Entering the password recall procedure l Press and hold AUTO on the projector or remote control for 3 seconds The projector will display a coded number on the recall as the screen s e 2 Write down the number and turn off your projector 3 Seek help from the local BenQ service center to decode the number You may be required to pro
71. u adjust the image size and focus and check that the projected image is free from distortion To display the test pattern open the OSD menu and go to the SYSTEM SETUP Advanced gt Test Pattern and press 4 9 to select On 38 Operation Using the teaching templates The projector provides several preset patterns for various teaching purposes To activate the pattern l Open the OSD menu and go to the DISPLAY gt Teaching Template and press A V to select Blackboard or Whiteboard 2 Press lt to choose the pattern you need 3 Pres MODE ENTER to activate the pattern Teaching Whiteboard Blackboard Template Letter Formation Worksheet Coordinate Chart Operation 39 Presenting from USB Reader This feature allows you to browse the image and document files stored on a USB flash drive connected to the projector It can eliminate the need for a computer source 40 Cr Supported file formats JPEG PG BMP Thai filename is not supported TIFF A square box will display on the filename for unidentified characters Files in GIF TIFE PNG and BMP formats can be displayed for the file size smaller than WXGA 1280 x 800 only If a folder consists of more than 200 files only the first 200 files can be
72. used as directional arrows to select the AN D not look into the laser light desired menu items and te make window or shine the laser light beam on yourself or others See the warning messages on the back of the adjustments remote control prior to using it I7 SOURCE The laser pointer is not a toy Parents should be Displays the source selection bar mindful of the dangers of laser energy and keep 18 MICIVOL IMICIVOL this remote control out of the reach of children function Controlling your smart device with the remote control MX666 When the projector projects the content from your MHL compatible smart device you can use the remote control to control your smart device To enter the MHL mode press and hold AUTO for 3 seconds The following buttons are available for controlling your smart device Arrow keys W A Up Down lt Left gt Right MENU EXIT MODE ENTER 0 9 MHL control buttons To leave the MHL mode press and hold AU TO for 3 seconds 12 Introduction Remote control MW665 and for Japan I0 m N SA o Il o 8 o 12 I3 e 14 POWER 15 Toggles the projector between standby mode and on Info 16 Shows the status information of the projector MENU EXIT Turns on the On Screen Display OSD menu Goes back to previous OSD menu exits and saves menu settings 17
73. version and press lt gt to select a suitable color space C This function is only available when the HDMI HML or HDMI input port is in use Magnifying and searching for details If you need to find the details on the projected picture magnify the picture Use the direction arrow keys for navigating the picture Using the remote control Pres ZOOM ZOOM or Digital Zoom Digital Zoom to display the Zoom bar Press ZOOM or Digital Zoom to magnify the center of the picture Press the key repeatedly until the picture size is suitable for your need 2 Use the directional arrows A V lt gt on the projector or remote control to navigate the picture 3 Torestore the picture to its original size press AUTO You can also press ZOOM or Digital Zoom When the key is pressed again the picture is further reduced until it is restored to the original size Using the OSD menu l Press MENU EXIT and then press 4 gt until the DISPLAY menu is highlighted 2 Press V to highlight Digital Zoom and press MODE ENTER The Zoom bar displays 3 Press A repeatedly to magnify the picture to a desired size 4 To navigate the picture press MODE ENTER to switch to the panning mode and press the directional arrows V lt gt on the projector or remote control to navigate the picture 5 To reduce size of the picture press MODE ENTER to switch back to the zoom in out function and press AUTO to restore the picture
74. via the OSD menu Setting the Lamp Mode Setting the projector in Economic SmartEco LampSave or LumenCare mode extends the lamp operation life To set Economic SmartEco LampSave or LumenCare mode go into the SYSTEM SETUP Advanced gt Lamp Settings gt Lamp Mode menu and press lt P gt Lamp mode Description Normal Provides full lamp brightness Lowers brightness to extend the lamp life and decreases the fan Economic N noise SmartEco Adjusts the lamp power automatically depending on the content brightness level LampSave Adjusts the lamp power automatically and lowers the brightness to extend the lamp life L inenCare Keeps the image brightness constant without losing too much brightness after long term usage Setting Auto Power Off This function allows the projector to turn off automatically if no input signal is detected after a set period of time to prevent unnecessary waste of lamp life To set Auto Power Off go into the SYSTEM SETUP Basic gt Operation Settings gt Auto Power Off menu and press lt gt If the preset time lengths are not suitable for your presentation select Disable The projector will not automatically shut down in a certain time period Maintenance Timing of replacing the lamp When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp please install a new lamp or consult your dealer An old lamp may cause a malfunction
75. vide proof of purchase L m documentation to verify that you are an authorized user of the projector RECALL PASSWORD Recall Code 255 255 255 255 Changing the password l Open the OSD menu and go to the SYSTEM SETUP Advanced Security Settings gt Change Password menu 2 Press MODE ENTER The message INPUT CURRENT PASSWORD appears 3 Enter the old password i If the password is correct another message INPUT NEW PASSWORD displays ii If the password is incorrect the password error message displays lasting for three seconds and the message INPUT CURRENT PASSWORD displays for your retry You can press MENU EXIT to cancel the change or try another password 4 Enter a new password IMPORTANT The digits being input will display as asterisks on screen Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it Password 1 Keep this manual in a safe place 5 Confirm the new password by re entering the new password 6 You have successfully assigned a new password to the projector Remember to enter the new password next time the projector is started 7 To leave the OSD menu press MENU EXIT Operation 27 Disabling the password function To disable password protection go back to the SYSTEM SETUP Advanced gt Security Settings gt Change Security Settings menu after opening the OS
76. yes If the projector is not placed on a flat surface or the Be careful when you press the quick screen and the projector are not perpendicular to release button as it is close to the each other the projected image becomes exhaust vent where hot air comes trapezoidal To correct this situation see Switching m input signal on page 28 for details Auto adjusting the image In some cases you may need to optimize the picture quality To do this press AUTO on the projector or remote control Within 3 seconds the built in Intelligent Auto Adjustment function will re adjust the values of Frequency and Clock to provide the best picture quality The current source information will be displayed in the corner of the screen for 3 seconds C This function is only available when PC signal analog RGB is selected Fine tuning the image size and clarity Adjust the projected image to the 2 Sharpen the image by rotating the size that you need using the zoom focus ring Operation 23 24 Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom It occurs when the projector is not perpendicular to the screen To correct this you will need to manually correct it following ONE of these steps Press V7 on the projector or remote control to display the Keystone correction page Press N 2D Keystone to correct keystoning at the top of the image Pr

MX666/MW665 Digital Projector User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents