mitex FI VFC 2 x 20 - Downloads & Support
Contents
1. Interface 3 3 Profibus DP Interface 3 3 1 Configuration data The user can adapt the data width for data transfer to individual needs with the data configuration function Various identifiers are required to this end which can be entered in any desired order NC Data Number of Function Description O Identifier Bytes en cen OX Ih 2 inputdata 2bytes output data 1 byie output data 2 byles output data 16 bytes put ouput data 1 bye each input output data 2 bytes each input output data 3 bytes each c Default configuration Configuration byte 0 12 3 input bytes Configuration byte 1 2F 16 output bytes Page 8 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface 3 3 2 Input Data The device supports input data which have been configured to the length selected during configuration The minimum number of input data is 0 bytes and the maximum number is 3 bytes 3 3 3 Output Data The device supports output data which have been configured to the length selected during configuration The minimum number of output data is 0 bytes and the maximum number is 47 bytes 3 3 4 Diagnosis Data The device does not support any extended diagnosis data The default diagnosis is used 3 3 5 User Parameter Data2. User parameter data are not supported by the device However a test is run to determine if user parameter data are transferred by the Profibus master If parameter data are transferred Profibus initialisation is disabled and the slave s parameters must be reconfigured Note Standard parameters configuration is required and is normally installed by the utilised DP configurators Page 9 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface 3 4 Control via the Profibus DP Interface The control frames described in chapter 3 6 are transmitted by the user via the Profibus DP interface DP Output Data Index Contnt Significance Toggle byte Bits 0 to 6 The control frame is executed once for each change Bit 7 After setting bit 7 the control frame is executed again and again automatically 1 to Control frame as defined in chapter 3 6 max 46 DP Input Data Index Content Significance pO LN In toggle Same as toggle byte after executing the frame byte Response frame Asdefinedinchapter3 6 Note When DP communication is first initialised all DP output and input data are internally set to 0 at the device For this reason the toggle byte of the first executed control frame may not
3. all characters after clearing the display 2 display all characters except for blanks 20h 3 display all characters except for blanks 20n after clearing the displa Response frame Index Content Significance RS232 DP Display EEPROM text 1 2 Error code 0 30h no error 1 31s error occurred Page 12 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface Note At the end of each line a line break occurs to the first column of the next line or the first line Example Display EEPROM text number 1025 2 0401 in normal display mode at the default position DP control frame 544 004 005 00 004 0115 044 For control via Profibus DP it is advisable to set bit 7 of the toggle byte in this case Only the text number must then be changed DP indices 6 and 7 in order to display a different text Page 13 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl VFC 2 x 20 STe Alphanumeric VFC Display with Profibus Interface 3 6 2 Displaying an Online Text Control frame Index Content Significance RS 232 DP 7i Display online text 1 2 Attribute Bit 0 0 reserved Bit
4. be set to 0 Page 10 microSYST Systemelectronic GmbH Albert Einstein Stra e 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl VFC 2x20 Alphanumeric VFC Display with Profibus Interface 3 5 Control via the RS 232 Interface The control frames described in chapter 3 6 are transmitted via the RS 232 interface by the included PC program It must be assured that the pause between the individual frame bytes included in the control frame does not exceed 3 ms during transmission The end of the frame is identified by means of a pause of at least 5 ms The display unit transmits the response frame immediately after execution of the command Page 11 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface 3 6 Control Frames The control frames used for controlling the display unit are defined below These frames are transmitted by the user via the Profibus DP interface and by the included PC program via the RS 232 interface 3 6 1 Displaying an EEPROM Text Control frame Index Content Significance RS 232 DP Display EEPROM text 1 2 Attribute Bit 0 0 reserved Bit 1 1 blinking text display Bits 2 to 7 0 reserved 2 3 0 display all characters 1 display
5. 1 1 blinking text display Bits 2 to 7 0 reserved 2 3 0 display all characters 1 display all characters after clearing the display 2 display all characters except for blanks 20h 3 display all characters except for blanks 20n after clearing the displa 3 4 415 5 6 6 7 to Text ASCII characters 0 to 255 see character set table in the max 45 46 appendix Response frame Index Content Significance RS232 DP 0 1 Display online text 1 2 Error code 0 30n no error 1 31n error occurred Note At the end of each line a line break occurs to the first column of the next line or the first line Example Display ABC at position X 10 and Y 1 blinking display clear display first Page 14 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST Alphanumeric VFC Display with Profibus Interface DP control frame Olh previously 00 4F 021 015 OAn Olh 034 41 hs 42h 43h The toggle byte must be changed last in this case in order to initialise execution of the command 3 6 3 Displaying a Number Control frame Index Content Significance RS 232 DP 1 2 Attribute Bit 0 0 reserved Bit 1 1 blinking text display Bits 2t0 7 0 reserved 2 3 0 display all characters 1 display all characters after clearing the display 2 display all character
6. 2 Japanese 29 6 6 Versions Overview 30 Page 3 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl VFC 2x 20 Alphanumeric VFC Display with Profibus Interface 1 General This bus compatible VFC monitor with Profibus DP interface has been designed as a panel mount display for industrial applications The monitor consists of a vacuum fluorescent display Two lines of text with 20 characters each can be displayed Each character is displayed with a resolution of 5 x 7 pixels Character height is 10 5 mm 0 41 inches A physical RS 485 interface with Profibus DP protocol is used for serial communication Predefined texts can be downloaded and saved to the display via the RS 232 interface Features Profibus DP interface Text downloads via RS 232 Text memory up to 255 texts with 40 characters each Metal DIN panel mount housing with special surface finish Designed for use in industrial applications Page 4 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface 2 System Overview The display DP Slave is connected to the DP master via Profibus 7 Up to 127 Users RS232 Download Profibus DP Page 5 mic
7. Epe be 671 QUE id u SEL 1 one LLI sag P an LELELLJ LL m Bi Hs EC ETT deb IES OH Lx Pe wee a x m gt i te E N ous sen ji Hi sens ous fils n s ii i i Sae spa If Et i pos snas JE 8 s s senes aneeue T as oe eases o In 1 n Be eye ij n sgessas miss ied ences xd iid E line allen L4 us as e LIEN NE te N H z u uL u iL o 5 5 O lt i a e 2 E 3 a m e o v N e wo N o m O Q Ww LL Page 29 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl VFC 2x20 Alphanumeric VFC Display with Profibus Interface 6 6 Versions Overview Comments Description 4 11 2003 Kreuzer 1 19 2006 Kreuzer Chapter Declaration of Conformity added 4 30 2009 Kreuzer DIP switch 1 DIP8 and DIP9 always in OFF position 4 4 2013 Company address declaration of conformity warranty 10 23 2013 Logo Certified per DIN EN ISO 9001 Page 30 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de
8. Front Panel EEG N bl N ora ap N S LS N N N Control Panel Control Panel Page 24 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface 6 Appendix 6 1 Standard Equipment Display in the current software and hardware versions Mounting kit M4 screw clamps Sealing frame User s manual PC software on floppy disk Floppy disk with DDBF 6 2 Maintenance and Care Observe the following instructions in order to assure best possible performance of the display e The display must be switched off before cleaning Only solvent free cleaners may be used because plastic components may otherwise be damaged Under no circumstances may moisture be allowed to enter the interior of the device during cleaning e Protect the display from excessive humidity extreme vibration direct sunlight and extreme temperatures Non observance may lead to malfunctioning or destruction of the device Under certain circumstances electrical shock fire and explosion may occur as well Information concerning allowable ambient conditions in particular recommended temperature and atmospheric humidity ranges can be found in the chapter entitled Technical Data e The display may not be placed into service if the device and or the power cable
9. VFC Display with Profibus Interface DIP Switch 2 6b 0 8 Reserved Notallowed Must be set to OFF 9 Bus termination set nmotset Allowable DP addresses 0 to 126 PE L This connector serves for the earth connection Page 22 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface 5 Housing Dimensions Designation B H Dimensionin mm 216 96 86 42 D Page 23 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl VFC2x20 Alphanumeric VFC Display with Profibus Interface 5 1 Front Panel Cutout min 10 mr Designation d e Dimension in inches 5 2 Installation Mounting The device has been designed for mounting to a panel The tabs provided to this end are bent up to enable fastening of the clamps after the device has been inserted into the panel cutout A rubber gasket makes a watertight seal between the device s front panel and the control panel IP65 Rubber Gasket Housing Be Housing PA Fastening Clamp P4 Front Panel EE
10. are known to be damaged e Do not attempt to open or repair the device yourself The guarantee is rendered null and void if the device is tampered with by unauthorised persons e Observe all notes and instructions included in this user s manual Page 25 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface 6 3 Warranty Liability For the product liability is assumed for defects which existed at the delivery date according to our General Terms and Conditions Technically changes as well as errors are excepted A claim for delivery of a new product does not exist The buyer has to check the received product immediately and indicate evident defects at the latest 24 hours after detection Non observance of notification requirements is equated with acceptance of the defect Not immediately visible defects have to be indicated immediately after their perception too Generally defects and their symptoms must be described as accurately as possible in order to allow for reproducibility and elimination The buyer must provide for access to the relevant device and all required and or useful information at no charge and must make all of the required data and machine time available free of charge The guarantee does not cover defects which result from non obs
11. connector P Pin Download RS232 TL 1 ne es 20 77 EL es 40 eo Connection mitex PC mitex PC Pin Pin RxD 2 2 RxD TD 3 L 3 TxD GND 5 5 QGND Page 19 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface Profibus DP 9 pin sub miniature socket connector 4 HIS only for bus termination Power prt T pur a LEDs BUS RUN ERROR BUS yellow Continuously illuminated during DP communication RUN green Blinks at approx 2 Hz for monitoring microcontroller functioning ERROR red Page 20 microSYST Systemelectronic GmbH Albert Einstein Stra e 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl VFC2x20 Alphanumeric VFC Display with Profibus Interface DIP Switch 1 Japanese European character set character set DIP switches 1 to 5 7 and 8 are reserved OFF and must not be changed see chapter Font Table Page 21 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric
12. en The correspondence of the above mentioned product with these requirements is proved by the fact that these products meet with the following single standards Nummer Bezeichnung Europaische Norm 2004 108 EG Elektromagnetische Vertraglichkeit EMV EN61000 6 2 2006 EN61000 6 4 2007 Weiden den 04 04 13 pe Ae Leiter operatives Geschaft COO Prokurist Authorized Signatory Page 27 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface 6 5 Font Table 6 5 1 European 2 3 4 s e l 7 8 e A B c D E F o Co gt N a o G o z j o c O gt o 4 7 T mn oO m oye E SP Page 28 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de SYST e VFC2x20 Alphanumeric VFC Display with Profibus Interface IE 8 9 S E itex FI mi 6 5 2 Japanese Bgl ne 28 gt Boot of 8 ole ot eels oh en o e aa TEE PE ER SR
13. ervance of the prescribed conditions of use or from improper handling If the device has been placed at the disposal of the buyer for test purposes and has been purchased subsequent to such testing both parties agree that the product is to be considered used and that it has been purchased as is No guarantee claims may be made in such cases The General Terms and Conditions of microSYST Systemelectronic GmbH in current version apply as well Page 26 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl VFC 2x 20 Alphanumeric VFC Display with Profibus Interface 6 4 Declaration of Conformity EG Konformitatserklarung Declaration of EC Conformity Produktbezeichnung Product name Produktbeschreibung Product description Hersteller Manufacturer mitex FI DP VFC 2 x 20 Alphanumerische VFC Anzeige mit Profibus Interface Alphanumeric VFC Display with Profibus Interface microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Das bezeichnete Produkt stimmt mit der folgenden Europaischen Richtlinie berein We herewith confirm that the above mentioned product meets the requirements of the following standard Die bereinstimmung des bezeichneten Produktes mit den Vorschriften der Richtlinie wird nachgewiesen durch die vollst ndige Einhaltung folgender Norm
14. isplayed This message includes the device designation the selected DP address and the number of texts stored in memory As soon as DP communication is initialised the power up message disappears and the yellow BUS LED is illuminated continuously After DP communication has been ended the power up message reappears and the yellow BUS LED goes out DP communication may not be active when texts are being downloaded via the RS 232 interface After text downloading has been completed DP communication can be reactivated 3 2 Performance in the Event of Error DP communication is not possible in the event of a faulty Profibus connection and the yellow BUS LED does not light up Please check for correct wiring to the Profibus interface in this case bus termination etc In addition make sure that the selected device address DIP switch setting is correct and that input and output data lengths are within the allowable limits If the integrated microcontroller malfunctions the red ERROR LED blinks Make sure that supply voltage tolerances are complied with in this case If the above described remedies do not eliminate the respective error please return the device for repair Page 7 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl VFC 2x 20 Alphanumeric VFC Display with Profibus
15. microSYST mitex Fl VFC2x20 Alphanumeric VFC Display with Profibus Interface User s Manual microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl VFC 2x20 Alphanumeric VFC Display with Profibus Interface Table of Contents 1 GENERAL 4 2 SYSTEM OVERVIEW 5 3 TECHNICAL DATA 6 3 1 System or Device Start Up 7 3 2 Performance in the Event of Error 7 3 3 Profibus DP Interface 8 3 3 1 Configuration data 8 3 3 2 Input Data 9 3 3 3 Output Data 9 3 3 4 Diagnosis Data 9 3 3 5 User Parameter Data 9 3 4 Control via the Profibus DP Interface 10 3 5 Control via the RS 232 Interface 11 3 6 Control Frames 12 3 6 1 Displaying an EEPROM Text 12 3 6 2 Displaying an Online Text 14 3 6 3 Displaying aNumber 15 3 6 4 Writing Text to the EEPROM 17 3 6 5 Reading Text from the EEPROM 18 4 CONNECTOR PIN ASSIGNMENTS 19 5 HOUSING DIMENSIONS 23 5 1 Front Panel Cutout 24 5 2 Installation Mounting 24 Page 2 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl VFC 2x20 Alphanumeric VFC Display with Profibus Interface 6 APPENDIX 25 6 1 Standard Equipment 25 6 2 Maintenance and Care 25 6 3 Warranty Liability 26 6 4 Declaration of Conformity 27 6 5 Font Table 28 6 5 1 European 28 6 5
16. roSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface 3 Technical Data General Specifications Display type Resolution Characters lines Character height Display colour Operating voltage Power consumption Interfaces Baud rate Addresses Display Housing Housing dimensions Display area Mounting Protection Operating temp Storage temperature vacuum fluorescent 5 x 7 pixels 2 lines of 20 characters each 10 5 mm 0 41 inches cyan 24 VDC 20 protected against polarity reversal 300 mA at 24 VDC operating voltage Bus Profibus DP Download RS 232 9 6 kBaud to 12 Mbaud 0 to 126 ASCII character set additional characters see table in chapter appendix DIN panel mount housing metal with special surface finish see chapter 5 147 x 29 mm 5 79 x 1 14 inches screw clamps front panel IP65 0 to 50 C 25 to 60 C Page 6 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface 3 1 System or Device Start Up After supply power has been switched on the green RUN LED starts blinking and the power up message is d
17. rt Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface 3 6 5 Reading Text from the EEPROM Control frame Read text from EEPROM LOW byte L Memory location 0 to 255 LOW byte Memory location 0 to 255 HIGH byte always 0 Response frame Index RS232 Content Significance Read text from EEPROM Error code 0 30n no error 1 31n error occurred 0 to 65535 e ee 0 to 65535 40 bytes 1 line 20 bytes 2 line 20 bytes encoded Notes e Memory location 0 text number number of existing texts 1 to 255 not used Text e Inthe event of an error only the error code is returned indices 2 to 43 do not apply e This command may only be executed via the RS 232 interface e This frame has no significance for the user It is used by the PC software only Page 18 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl VFC 2x 20 Alphanumeric VFC Display with Profibus Interface 4 Connector Pin Assignments Power U PE Profibus DP DIP Switch 1 DIP Switch 2 nnnanann anannennnn O Download RS232 9 pin sub miniature plug
18. s except for blanks 20h 3 display all characters except for blanks 20n after the displa 0 left to 19 right X position of the first character 0 top to 1 bottom Y position of the first character 5 6 Data format unsigned char value 9 10 unsigned int value 9 10 LSB 10 11 MSB unsigned long value 9 10 LSB 12 13 MSB signed char value 9 10 signed int value 9 10 LSB 10 11 MSB signed long value 9 10 LSB 12 13 MSB signed values in two s compliment representation 0 decimal representation or precede with format 1 decimal representation or precede with 2 hexadecimal representation 7 8 1 to 8 displayed places decimal representation unused places places blanks 20n plus or minus sign included 8 9 Layout 0 right justified representation 1 left justified representation 11 12 Valence 2416 12 13 Valence 2 24 MSB most significant byte Page 15 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface Response frame Index Content Significance RS232 DP Error code 0 30h no error 1 31n error occurred Atthe end of each line a line break occurs to the first column of the next line or the fir
19. st line Example Display decimal number with plus or minus sign signed int value 1234 FB2E DP control frame 80h 5A 00 00 00 00 044 00 O5h 00 2E FB After entering DP indices 1 through 11 DP index 0 toggle byte is set to 80 If another value needs to be displayed subsequently only the number needs to be changed indices 10 and 11 Page 16 microSYST Systemelectronic GmbH Albert Einstein StraBe 7 92637 Weiden Tel 49 961 39166 0 Fax 49 961 39166 10 www microsyst de info microsyst de microSYST mitex Fl 5 VFC 2x20 Alphanumeric VFC Display with Profibus Interface 3 6 4 Writing Text to the EEPROM Control frame Index RS 232 2 Content Significance 0 S 53i Write text to EEPROM Memor location 0 to 255 LOW byte 4 Textnumber 0 to 65535 HIGH byte Cd 40 bytes 1 line 20 bytes 2 line 20 bytes Response frame a MN Write text to EEPROM Error code 0 30h no error 1 31n error occurred Notes e Memory location 0 text number number of existing texts 1 to 255 permitted Text not used e Texts must be saved to the memory locations sorted according to text number lowest text number at memory location 1 e This command may only be executed via the RS 232 interface e This frame has no significance for the user It is used by the PC software only Page 17 microSYST Systemelectronic GmbH Albe
Download Pdf Manuals
Related Search