USER MANUAL
Contents
1. After wind generator brakes it will stop rotating or rotate at a very slow speed The wind generator is unable to generate electricity Brake disappears and the wind generator quits braking state Page 13 MANBLAN V Protection Mechanism Protection contents General over speed brake or brake off 2 Over speed brake or brake off under continuous strong wind Exceeding safe temperature Temperature decreases to safe temperature Protection description If the rotate speed of wind generator exceeds the preset rotate The controller speed of braking it will automatically brakes through three phase has automatic short circuit and the brake is off automatically after 3min braking function If there are more than successive 3 overspeed brakes within 30min it will be determined as continuous strong wind and the brake can be off automatically only after 4h When it exceeds the safe temperature because of overhigh ambient The controller temperature or overhigh temperature caused by heavy current the has a built in system will enable over temperate protection automatically disable temperature wind generator and photocell input but the output will not be testing module affected Over temperature protection is freed and the system recovers to normal state This controller has good heat dissipation measures and the over temperature protection module will not be enabled un2. need to look back certain parameter press to display parameters counter cyclically In this interface as shown in Fig 4 5 4 1 press A to enter into output mode setting of Channel 1 and 2 DC load Page 10 4 5 5 DC load output mode setting interface no FB aya xi lt lt xt Charge DC OUT i th Be on LOAL In this Manual Channel 1 load is used as an example and its setting process is stated 4 5 5 1 Normally open mode interface Lo A EAH 6 LS ne xt Charge DC OUT 1 e A AY an LOAD MANBLAN In this interface as shown in Fig 4 5 5 1 press A and the Channel 1 or 2 load setting interface can be switched over For each channel press O set confirm key first and the screen will display a SET sign and then press A or 5 Channel 1 load can be switched over among the three output modes normally open light controlled on off light controlled on time controlled off Users only need to select the mode they need and then press O to confirm and press key to save and quit 4 5 5 2 Output mode interface of light controlled on off Page 11 AF esc TE Hmh 08 ia SEES 3 Charge DC OUT YUL ON xt LOAD 4 5 5 3 Output mode interface of light controlled on time controlled off Syn z 3 Charge DC OUT Ei SETH an LOAD The output mode setting of Channel 2 is the same and its interface is as follows 4 5 5 4 Output mode setting interface of Channel 2 load
3. to enter into next parameter state and the current power of wind generator can be viewed 4 5 2 4 View the power of wind generator 4 Z anae j a Charge DC OUT JKL AIL xt 000 WIND 0 00W in the picture shows the current power of wind generator Press A solar PV parameter state and the current voltage current and power of solar PV can be viewed 4 5 3 Operating parameter state of solar PV module 4 5 3 1 View the voltage of solar PV FEB Sve 203 q S a Charge DC OUT JG Ha Yt xt 0 00 De 0 00V in the picture shows the current voltage of solar PV Press A to enter into the next parameter state and the current of solar PV can be viewed 4 5 3 2 View the current of solar PV Page 9 MANBLAN FH Bsa IE r SSS Charge DC OUT xt 000 PY 0 00A in the picture shows the current voltage of solar PV Press A to enter into the next parameter state and the current power of solar PV can be viewed 4 5 3 3 View the power of solar PV 4 5B ERAH se r SSS e Charge DC OUT xt 000 PY 0 00W in the picture shows the current voltage of solar PV Press A to enter into D load parameter status and the current of DC load can be viewed 4 5 4 Operating parameter state of load 4 5 4 1 View the current of DC load ne Svea We q p pE Charge DC OUT Di AX xt 0 00 LOAD So far the operating parameters of various parts of the system have been all viewed if you
4. I TH EA 20 SS nn x Charge DC OUT I 4 ON LOAD 4 5 6 Manual brake operation MANBLAN To ensure the operation safety of wind generator and for the convenience of users this controller is so designed that the wind generator can be braked manually under any state The specific process keep O confirm key on the panel pressed first and gt 4 then press ESC key and hold for about 5min Loosen the key to enter manual braking state and there will be Brake displayed at the top right corner of the display interface If you want to quit manual braking state repeat the above operation namely keep O confirm key on the panel pressed first and then press ESC key and hold for about 5min Loosen the key to quit manual braking state Brake at the top right corner of the display interface will disappear The specific interface is shown as follows 1 Manual braking interface Brake appears at the top right corner of the display interface Page 12 MANBLAN lt means the wind generator brake when brake appeard here i ag ne sen er Ssis x5 Charge DC OUT 17 ESET ta AR i an O LOAD Brake appears and the wind generator brakes 2 Quit manual braking Brake at the top right corner of the display interface It means the wind generator quits braking when brake disappears here N nn Re G RAE y fr xt Charge DC OUT le KSETH ta zR en amp LOAD
5. MANBLAN USER MANUAL MBWS B1 IntelligentBoost Wind Solar Hybrid Alpek Co LTD Moscow Chechersiy proezd 3 5 manblan ru 7 495 502 65 84 info manblan ru 20120314 VERSION 1 MANBLAN Safety Caution 1 Thank you for purchasing our controller Before you install and use the product please carefully read the User s Manual and properly keep it 2 The controller shall be installed by an experienced technician in strict accordance with the User s Manual to guarantee that it can work normally 3 Keep the product free of contact with corrosive gas and humid environment for a long time 4 Be sure not to place the product at a place where it is exposed to humidity rain sun severe dust vibration corrosion or strong electromagnetic interference 5 Please don t open the product s casing to repair it by yourself Table of Contents Product OV EIVIN EEE RN EEREESCRES EEE SABERSBEFSERSUERERS 1 Il Description of Mode isn 2 Ill Installation Specification u 3 IV LCD Operation and Display Instructions sesesesesessssesesecececececsosesesesesecececececeosssesesesececeoeee 4 4 1 Descrption of KOVS need 5 4 2 Description of display content sesessececesesssessssesesesesecececscsososesecececececeseesesesesecececeee 5 4 3 Day and night identification inserieren 7 AG Output MODE ernennen 7 AS Instructions for control Panel nun 8 V Protection Mechal iii sscscrsatisn neii a 14 Vi Performante Paramete
6. UT 3 Connect the storage battery to the BATTERY terminal of back panel of equipment with the cable with copper conductor of 6mm2 and above A reverse connection between anode and cathode of the storage batteries is forbidden in order to avoid damaging components 4 When wind generator is under static or low speed running status no wind connect the wind generator output line to the WIND INPUT terminal of back panel of equipment 5 Shield and then connect the solar cell panel to the SOLAR INPUT terminal of back panel of equipment according to anode and cathode 6 Set corresponding parameters to select the load output mode via the keys on the controller s LCD IV LCD Operation and Display Instructions Diagram of panel keys Page 4 MANBLAN 4 1 Description of keys Symbol Function description Add or display the next value if under browsing status press it to switch to next parameter display if under setting status press it to add the current parameter value modified Reduce or display the previous value if under browsing status press it to switch to previous parameter display if under setting status press it to reduce the current parameter value modified Setting confirmation if under browsing status press it to enter the setting status if under setting status press it to store the parameters and return to the browsing Status Cancellation manual switch if under setting status press it to ret
7. WM ASS SOLARINPUT WIND INPUT De EIEZIIEIEIEBEI EI FE RE I Output terminal connection diagram of MBWS Bx wind solar hybrid controller with single channel dimming signal optional Controller 2 Controller 1 i tees io i Rs485 explanation Computer Rs485 interface GND Description Each controller is provided with aRS485 communication port When two controllers are connected they shall be connected in a way of anode to anode cathode to cathode and GND to GND and finally connected to the RS485 port behind the computer via the third RS485 DOTU es and the like Connection diagram of MBWS Bx wind solar hybrid controller with communication port RS 485 optional Page 3 MANBLAN Dimmer port and communication port RS485 are optional so the customer shall clearly specify what you need otherwise we will deliver the one in standard configuration After the parts of wind solar hybrid generator system and photovoltaic panel are installed and external circuit construction is completed it is required to connect and operate the system parts safely and reliably according to the following sequence 1 Open the package to confirm that the equipment is not damaged in transportation 2 Connect the DC load to DC OUTPUT terminal The loads of two channels share the same anode Connect the first channel load to and 1 of DC OUTPUT and the second channel load to and 2 of DC OUTP
8. cker at this time you need to eliminate the excessive load and then press Esc key to OTTE ano ACE ota recover the output under short circuit protection av short circuit symbol 9 will be on at this time you should check the load line and then press Esc key after confirmation for normality to manually recover it to original status See Figure An icon of manual brake when 4 2 it is on it indicates under manual brake status otherwise status of manual brake unlocked See Figure An icon of the item browsed 4 2 currently itl A current unit A Page 6 MANBLAN V voltage unit V W power unit W H hour M minute appears it indicates light controlled on off and when appears it indicates light controlled on time controlled off Output on off status Two channel load output Channels 1 and 2 interface 4 3 Day and night identification It is night if the photocell voltage exceeds the light controlled on voltage can be set by users for continuous 1min It is day if the photocell voltage exceeds the light controlled off voltage can be set by users for continuous 1min 4 4 Output mode Normally open output mode The voltage of battery is normal and within the rated load The controller outputs will full power normally Light controlled on time controlled off output After dark see 4 3 Day and night identification it outputs according to mode the set load up
9. der non extreme cases Page 14 MANBLAN VI Performance Parameters MBWS B1 Input voltage range Maximum input power Input voltage range Input current range initial value Solar energy Maximum input power The voltage of the solar maximum power point Number of output circuits 2 channel or 1 channel with dimming signal aeons En 4 Normally open light controlled off light controlled on time ntrol mode Output ann controlled off Maximum output current of 10A each loop Output Customized LCD Man machine interface optional O 100V i ini 0 30A 15A O 22A 8A u BR 17 20V 34 40V 68 80V Wind generator City electricity Optional complementary interface Operating temperature 20 450 C range Operating humidity range 35 85 no condensation W150 x H85 5 x D190 5mm Prominent part excluded Page 15 MANBLAN Vil Common Faults and Troubleshooting If the above statements are not satisfied or there is any abnormal phenomenon and the controller cannot return to normal please contact the after sale service or business personnel of our company for maintenance or replacement in a timely manner Storage battery box 5 flickers It is over discharged The storage battery is emptied Please fully charge the storage battery before use and there is no output The system detected output overlead and will disable the overloaded output Load icon Y flickers and loop the other loop wi
10. ll not be affected Please check the loads and remove there is no output the unnecessary or abnormal loads Press Esc to recover The system detected output short circuit and will disable the short circuited is on and there is no output output loop the other loop will not be affected Please check the loads and connection lines After troubleshooting press Esc to recover The temperature of the controller is too high and the over temperature The output is normal but itis not protection the wind generator brakes the photocell has open circuit but the charged output will not be affected When the temperature decreases to recovery temperature the system will recover VIII Warranty and After sale Service 1 The product quality warranty of our company is one year or in case of any defect or fault found within the quality warranty year as agreed in the contract our company will provide free maintenance service Place contact the after sale department or related business personnel of our company 2 The warranty range in this quality warranty clause is exclusive of damages caused by external factors such as damages caused by force majeure e g accident and natural calamities use not in accordance with the product specification improper use negligence refit repair improper installation improper testing improper transportation etc Page 16
11. per limit and the output off time is subject to the set time Light controlled on off output mode After dark see 4 3 Day and night identification it outputs according to the set load upper limit and the output is off after the dawn Page 7 MANBLAN 4 5 Instructions for control panel 4 5 1 Start up interface u FEB vied u mg a Ie I Br Ch arge DC OUT 25 FE Yh xt 0 00 A In the start up interface 0 00V shows the current voltage of storage battery Press A key to enter into wind generator parameter state and the current rotate speed voltage current and power of wind can be viewed 4 5 2 Wind generator operating parameter state 4 5 2 1 View the current rotate speed of wind generator x FEB Emin xe Charge DC OUT JKL AIL xt apg 0 00M in the picture shows the current actual rotate speed of wind generator Press A to enter into next parameter state and the current voltage of wind generator can be viewed 4 5 2 2 View the current voltage of wind generator s FE Bit IE q p Charge DC OUT JALAL te poo WNb 0 00V in the picture shows the current voltage of wind generator Press A to enter into next parameter state and the current of wind generator can be viewed 4 5 2 3 View the current of wind generator Page 8 MANBLAN gt gt FH e hae ye Charge DC OUT PXL AL xt gog WINP 0 00A in the picture shows the current of wind generator Press A
12. protection functions including solar cell reverse charging prevention protection solar cell reverse connection prevention protection Page 1 solar cell current limiting protection storage battery over charging over discharging protection storage battery open circuit protection storage battery reverse connection prevention protection overload short circuit protection lightning protection wind generator current limiting protection wind generator over speed protection automatic and manual brake protection of wind generator controller temperature monitoring over heat protection load over voltage protection MANBLAN x Note Except for storage battery reverse connection prevention protection other protections above won t damage the components 8 The controller casing made of high quality aluminum alloy is well designed and has an attractive appearance and a good heat dissipation performance 9 The controller is manufactured with strict production process and high quality industrial components so it can run reliably for a long time under cold high temperature or humid environment II Description of Model MBW S B1 B2 Internal code Solar energy Wind energy X Note Refer to VI Performance Parameters for detailed information Page 2 MANBLAN II Installation Specification Output terminal connection diagram of MBWS Bx wind solar hybrid controller with double channel standard configuration P
13. rs u ee 14 VII Common Faults and Troubleshooting sccscsccsccsccsccsccsccccecceccsccscccceccecceccscesceccescesences 16 VIII Warranty and After sale Service on anne 16 MANBLAN MANBLAN I Product Overview This controller is specially designed for high end small wind solar hybrid systems and applies to wind solar hybrid street lighting systems and wind solar hybrid monitoring systems Its main functions are shown as below 1 This controller being a high performance wind solar hybrid controller can control wind generators and solar cells to charge or discharge the storage batteries at the same time when charging it adopts high resolution PWM mode to charge the storage batteries via voltage and current limiting which can effectively prolong the storage batteries service life 2 The controller is provided with an accurate rotating speed measuring and controlling module so it can check the wind generator rotating speed in real time and also can realize over speed brake according to the set upper limit of safe rotating speed 3 The controller is provided with two channel DC output interfaces and each channel has a maximum output current 10A for each channel the user can independently set three kinds of different output modes namely light controlled on off light controlled on time controlled off and normally open 4 The controller is provided with MPPT maximum power point tracking function It via advanced algori
14. thm can automatically search the maximum power point to realize the maximum conversion from wind energy to electrical energy Through test compared with traditional controllers this controller can improve the charging efficiency by more than two times at maximum 5 The controller is provided with a customized LCD so the user can easily check and set the status of controller via the human computer interaction interface The items which can be checked storage battery voltage wind generator rotating speed wind generator voltage wind generator current wind generator power photocell voltage photocell current photocell power the first channel output mode the first channel output turn off time the second channel output mode the second channel output turn off time light controlled on voltage point light controlled off voltage point daytime or nighttime indicator storage battery status load status as well as the status of faults like over voltage under voltage over load and short circuit The items which can be set the first channel output mode the first channel output turn off time the second channel output mode the second channel output turn off time light controlled on voltage point and light controlled off voltage point 6 The controller is provided with a unique solar charging circuit with a small loss and heat which is of open circuit unloading mode so as to effectively prolong the solar cell s service life 7 Complete safety
15. urn to the browsing status but not to store the values modified if under browsing status use it as a Manual setting key in case of load short circuit or over load 4 2 Description of display content 5 ot or a C status of the battery 9 E hand brake A wind generator er a en nt W MN 7a A ope gt a gt B day and night HARGE x af L output interfaces 318 o BB B Bei ER I U i i ION OFF O iH Missa F Currently browsing items K the conditions on off output z a Ty yig Z m Ji I set state N units AA J output mode H Digital display area Page 5 MANBLAN Indicating wind generator BEE EEE A symbol of sun indicating ME aytime A symbol of moon indicating nighttime When the battery is fully charged 5 bars inside will all display Z when the storage battery is over discharged the symbol win flicker and then stop flickering upon recovery from over discharging status when battery storage is under over voltage status a battery status indicator bar will appear and A symbol of storage battery the over voltage symbol will flicker and then with the bars inside indicating stop flickering upon recovery from over voltage status the battery charge status Under a normal load indicator lamp P will appear when without output while indicator lamp will appear when with output under over load status load symbol HE fli
Download Pdf Manuals
Related Search