Instruction Manual and Quick Reference Guide
Contents
1. top right of display will indicate function Vibration Beep Both or Off A Quick Check to see what function is set is to push the MODE button while in the Calendar Clock mode The function that is set will respond each time you push the MODE button SETTING OF ALARMS AND COUNTDOWN TIMER Press MODE button to rotate to the mode you wish to set TR for COUNTDOWN TIMER A1 or A2 for ALARMS Press and Hold LAP RESET button until the digits blink While digits blink press the START STOP button to advance the blinking function to the time wanted Press the MODE button to change from hours to minutes and advance the time by pushing START STOP button For alarm settings hour s and or minute s can be set For countdown timer hour s and minute s can be set Press the LAP RESET button when completed Digits will stop blinking In the Alarm s mode the alarm indicator icon shows which alarm is activated To reset Alarms amp Countdown Timer for a different time repeat instructions as above HOURLY ALERT SETTING Press the MODE button until display is in an ALARM Mode A1 or A2 Repeat pressing the START STOP button until the Hourly Chime icon shows Located beside the A2 icon Copyright Global Assistive Devices Inc Fort Lauderdale Florida USA2. ESET button when it is ina stop position Split Timing on Stopwatch 1 Start the Stopwatch by pressing the START STOP button The stopwatch will start keeping time 2 Press the LAP RESET button The watch will continue counting the time even though you do not see it on the display The Icon at the top of the display will continue to flicker to show action and that counting continues 3 Press the LAP RESET button again and the display will change and show the time that has accumulated in total 4 To RESET the Stopwatch press the START STOP button and then press the LAP RESET button HOW TO SET THE SECOND CLOCK 1 Repeat Pressing the MODE button to show SECOND CLOCK T2 2 Press amp Hold the LAP RESET button until the Hours digits BLINK Press the START STOP button to rotate to the hour you wish to set In 12 Hr Mode use PM indicator for correct setting of afternoon or evening 3 Press the LAP RESET button when desired hour has been set NOTE Only the hour can be set in second clock mode The minutes and seconds will be the same as the Calendar Clock HOW TO USE THE EL BACK LIGHT Press the LIGHT button to light up the LCD display at any time The screen will be lit for approximately 3 seconds before going off automatically The EL back light will flash when an alarm is activated BATTERY INFORMATION Your watch uses a Standard 3 volt lithium CR2032 or equivalent battery Battery life will var
3. ODE button to display TR COUNTDOWN TIMER operating mode 2 Press and hold the LAP RESET Button until the hour digits BLINK Press the START STOP button to set the hour s wanted You can select from 0 to 23 hours 3 Press the MODE Button to go to the minutes The minute digits will BLINK Press the START STOP button to set the number of minutes wanted You can select from 0 to 59 minutes 4 Press LAP RESET button when you have finished The display will stop blinking TO START THE COUNTDOWN TIMER press the START STOP button after the countdown timer is set The timer will start to countdown To interrupt press the START STOP button Pressing the START STOP button again will start the countdown from where it last left off Note When Countdown Timer is set for more than ten minutes a short single reminder will advise you of 10 minutes remaining and then at 5 minutes remaining HOW TO USE THE STOPWATCH 1 Repeat Pressing the MODE button to show STOPWATCH on the display 2 To start the Stopwatch press the START STOP button The Stopwatch will start keeping time and the Icon symbol at the top of the display will flicker to show the action TO STOP THE STOPWATCH press the START STOP button Pressing the START STOP button again will start the stopwatch running from where it last left off The Stopwatch can count up to 23 hours 59 minutes and 59 99 seconds To RESET the stopwatch to zeros press the LAP R
4. VibraLITE 2 VIBRATION WATCH with Vibration Alarm won t disturb others Beep Alarm optional Electro Luminescent EL back light for viewing display at night Second Clock great when traveling in a different time zone Two Alarm Settings use for daily reminders wake up amp snooze medication Countdown Timer with manual reset can be set for minutes amp hours Use for reminders such as medication medical conditions timing presentations or procedures parking cooking Hourly Alert Chime Option 12 or 24 Hour clock Stopwatch OPERATING MODES 1 CALENDAR CLOUE 2 STOP PAT CI E Fag 2 SRO COCR 14 IST ALARM Your watch has six operating modes To go from one operating mode to another repeat pressing the MODE button for each mode to be displayed The operating modes will rotate in the order as listed above TO BECOME FAMILIAR WITH THE OPERATING MODES amp THEIR SYMBOLS ROTATE THROUGH EACH MODE BY PRESSING THE MODE BUTTON FIRST TIME SETTING OF YOUR CALENDAR CLOCK You must have this set for your Alarm Settings to be accurate When setting the Calendar amp Clock the rotation for setting is Seconds Hour Minutes 12 24Hr Date Month Day of Week ONLY when the digits are BLINKING can you set or change the setting The clock will stop blinking when no button is pressed for two minutes You cannot switch to another mode of operation while the display is blinki
5. eek A two letter abbreviation at the top of the display will BLINK Press the START STOP button to rotate to the correct day Example TU for Tuesday TH for Thursday 9 Press the LAP RESET button when you have finished the correct set up The display will stop blinking HOW TO SET AN ALARM CLOCK Setting procedure is the same for BOTH alarms 1 Repeat Pressing the MODE button to rotate to the alarm operating mode you want A1 1st ALARM or A2 2ND ALARM 2 Press amp Hold the LAP RESET button until the hour digits BLINK Press the START STOP button to rotate to the hour wanted Note In the 12 Hr Mode remember to use the PM indicator for correct setting 3 Press the MODE button to go to the minutes The minutes will BLINK Press the START STOP button to rotate to the minute wanted 4 Press the LAP RESET Button when finished The display will stop blinking The set icon will show on the display Your alarm is set When A1 Alarm is set the icon shows beside the PM indicator under the Alm1 When A2 Alarm is set the icon shows on the display beside the A1 icon under the Alm2 icon Note Calendar Clock Timer must be set for Alarm Time activation to be correct HOW TO TURN ON AND OFF THE HOURLY ALERT Note Hourly Alert is a short single reminder 1 Repeat Pressing the MODE button and select either 1st ALARM A1 or 2ND ALARM A2 2 Repeat Pressing START STOP button until the Hourly Alert indicator l
6. ng To exit and stop the blinking push LAP RESET button 1 Repeat pressing the MODE button until the 1 CALENDAR CLOCK operating mode shows on the display 2 Press amp Hold the LAP RESET button until the seconds digits begin to BLINK Press the START STOP button to reset the seconds display to 00 3 Press the MODE button The hour digits will begin to BLINK Press the START STOP button to rotate to the correct hour of the day WHEN IN THE 12 HR MODE A PM INDICATOR WILL APPEAR ON THE DISPLAY ABOVE AND LEFT OF THE HOUR DIGITS AS YOU ROTATE TO 12 HOURS THE PM MUST SHOW FOR SETTING CORRECT TIME FOR AFTERNOON OR EVENING BE SURE TO SET CORRECTLY FOR THE CURRENT TIME OF DAY 4 Press the MODE button to go to the minute digits The minute digits will begin to BLINK Press the START STOP button to rotate to the correct minute 5 Press the MODE button and the 12H or 24H mode will show and BLINK on the display Press the START STOP button to change from 12H to 24H or from 24H to 12H preference 6 Press the MODE button for the date of the month A number will BLINK at the top left corner of the display Press the START STOP button to rotate to the correct date of the month 1 31 7 Press the MODE button for the month A number will BLINK on the display Press the START STOP button to rotate to the current month of the year Example 6 for June 9 for September 8 Press the MODE button for the Day of the W
7. ocated beside the Alm2 indicator shows on the display Hourly alert is on when icon shows Hourly alert is off when icon doesn t show Hourly Alert ON OFF SETTINGS OF ALARMS Note To turn on or off First Alarm you must be in the A1 mode To turn on or off Second Alarm you must be in the A2 mode Repeat Pressing the MODE button to show alarm you wish to turn off or on 1ST OR 2ND ALARM Repeat Pressing the START STOP button to rotate alarm on hourly alert amp alarm off When Icon s shows alarm is set Alarm is off when icon does not show See previous illustration HOW TO ACTIVATE OR DEACTIVATE VIBRATION AND BEEP FUNCTION 1 Repeat Pressing the MODE button to the CALENDAR CLOCK mode 2 Repeat Pressing the START STOP button to rotate through the selection of settings When a function is activated its respective icon will be highlighted at the top right corner of the display Rotation will be Vibration ON Beep ON Vibration and Beep ON Vibration amp Beep OFF Select one of the four functions that you desire This can be changed at anytime by following steps 1 and 2 Alarm will stop automatically after approximately 20 seconds To stop alarm before the automatic stop press any button NOTE To verify setting the watch is in at any time press the MODE button With each press of the button the vibration and or beep will respond if set HOW TO USE THE COUNTDOWN TIMER 1 Repeat Pressing the M
8. ve the battery checked and or try resetting by pushing all four buttons at the same time and hold until the display clears Qualified service personnel should service this unit The user should not attempt to service the unit Servicing should be referred to GLOBAL ASSISTIVE DEVICES INC 1121 East Commercial Boulevard Oakland Park Florida US 33334 DISCLAIMER In no event shall Global Assistive Devices Inc be held liable for any special incidental indirect or consequential damages whatsoever including but not limited to damages for loss of property personal injury loss of privacy failure to meet any duty negligence and any other loss whatsoever however caused even if Global has been advised of the possibility of such damages This disclaimer of liability applies to any damages or injury including but not limited to those caused by any failure of performance of the product Responsibility for selection safety and Suitability of any product rests with the consumer Circumstances or consequences arising out of or in any way related to the use of or inability to use our products is the responsibility of the consumer Global Assistive Devices Inc cannot be held liable in any way VibraLlTE Z QUICK REFERENCE Model VL200 amp VL201 SELECTION OF VIBRATION BEEP BOTH OR OFF Press MODE button until the CALENDAR CLOCK mode shows on the display Repeat pressing START STOP button to select desired function Icon s at
9. y due to how often the EL back light and vibration function are used To maintain water resistance a qualified person should replace the battery ONE YEAR LIMITED WARRANTY Your VibraLiTE 2 is warranted to be free from defects in material or workmanship for One Year from the date of purchase This is a limited warranty and covers watch functions only This warranty does not apply to the battery the watchband or to any unit which has been subject to misuse negligence or accident This warranty is void if the watch has been tampered with altered or repaired other than by a qualified service center At its option GLOBAL ASSISTIVE DEVICES INC may select to replace the unit rather than repair it During the warranty period return the watch with dated proof of purchase in a secure package insured and with shipping charges prepaid No C O D packages will be accepted Please include a note describing the service required and include 10 00 check money order Visa MasterCard American Express or Discover for shipping and handling in the USA Other Countries please contact us for pricing OUT OF WARRANTY SERVICE Follow the same procedure for shipping to us as you would for warranty service Be sure to include a description of the problem An estimate will be submitted for your approval for any labor or parts not covered by the warranty before any work is performed SERVICE Before sending your unit for service ha
Download Pdf Manuals
Related Search