User Manual KI6103 - Kingfisher International
Contents
1. 10 You can use the UP and DOWN keys to select threshold number Press REF Enter to confirm For each wavelength there are 3 parameters 1 Up limit Communication will fail if the power level is above this value 2 Down limit warning communication is close to fail 3 Down limit communication will fail if the power level lower than this value 4 Use the UP and DOWN keys to alter the value followed by REF Enter to confirm By pressing Threshold again the instrument reverts back to measurement mode User Manual KI 6103 Optical PON Power Meter Issue 2 12 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer WWW kingfisherfiber com Store the test data Lsih 1490 1558 e 2 2 5D 32 H 13 1 3 1 HONE AONE NUE HONE NONE NONE HONE AONE NUE Hext A total of 100 test measurement data sets can be stored in the instrument After the internal memory is full the instrument will circulate to overwrite the first memory location To save measurement data press the Save ReCall key To review the stored data hold the Save ReCall for gt 2 seconds Then use the UP and DOWN keys to scroll through the stored data area To exit the memory press Save ReCall again User Manual KI 6103 Optical PON Power Meter Issue 2 13 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer www k ingfisherfiber com Backlight When working in a low light environment you can press th2. INTERNATIONAL Fiber Optic Test Equipment Manufacturer WWW kingfisherfiber com User Manual KI 6103 Optical PON Power Meter KIGTOS PON Optic PON Opticai Power Meter Warranty Information in this manual is given in good faith for the benefit of the user It cannot be used as the basis for claims against Kingfisher International or its representatives if accidental damage or inconvenience results from use or attempted repair of the equipment This Kingfisher International product is guaranteed against defective components and workmanship for a period of 1 year from the date of delivery unless specifically stated in the original purchase contract or agreement This warranty excludes optical connectors or incorrect use The warranty will be voided if the following instance happens 1 Opening the instrument 2 The instrument has been immersed in water or subjected to extreme environmental conditions Liability is limited solely to repair of the equipment User Manual KI 6103 Optical PON Power Meter Issue 2 1 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer Safety www kingfisherfiber com Take appropriate eye safe precautions when handling live fibre Operation Battery The instrument uses AA type alkaline batteries or NiMh rechargeable batteries e Avoid using mixed battery types e Do not use lithium batteries or other batteries with a nominal voltage greater than 1 8 V The instrument will
3. Test condition 23 3 C 40 60 relative humidity SC PC connector User Manual KI 6103 Optical PON Power Meter 1260 nm 1360 nm 10 dBm 35 dBm 15 dBm gt 30 dB 1480 nm 1500 nm 10 dBm 50 dBm 15 dBm gt 30 dB gt 30 dB 1530 nm 1570 nm 25 dBm 45 dBm 25 dBm gt 30 dB gt 30 dB SM 9 125 um Fixed select from LC SC FC PC or APC 0 5 dB lt 0 25 dB 0 1 dB lt 1 5dB LCD dBm dB Pass Fail 0 01 dB YES 3 AA batteries gt 20 hours 10 minutes after last key pressed 9V 1A DC input with LED charging indicator 0 50 C2 40 70 C2 lt 95 non condensing 190 x 95 x 45 mm 0 54Kg www kingfisherfiber com Issue 2 17 of 17
4. be damaged e Only charge NiMh rechargeable batteries Do not charge Alkaline batteries Avoid condensation The instrument is resistant to normal dust and moisture however it is not waterproof If moisture gets into the instrument remove the batteries and dry it out carefully for at least one hour before using it again Storage During prolonged storage remove batteries to eliminate the possibility of acid leakage Use only high quality batteries User Manual KI 6103 Optical PON Power Meter Issue 2 2 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer WWW kingfisherfiber com Check the instrument and part list Please contact us if you find anything missing after you open the case Standard accessories Instrument AC Adapter Charger User manual Carry case with strap 1 User Manual KI 6103 Optical PON Power Meter Issue 2 3 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer Instrument Description WO COIN DMD ON BR WIN FR PliPi Pi PI PI Pi Pil Pie CON DUB WIN RP O ONT upstream signal test port 1310 nm SC OLT Video downstream signal test port 1490 1550 nm SC LCD display ONT upstream Pass Fail LED indicator 1310 nm OLT downstream Pass Fail LED indicator 1490 nm OLT downstream Pass Fail LED indicator 1550 nm On Off key Measurement unit dBm dB key Backlight key Absolute Relative key Up key Threshold menu select key Test data storage key Down key Referenc
5. e ges key to turn the backlight on to help view the screen Pressing the X key again turns the backlight off User Manual KI 6103 Optical PON Power Meter Issue 2 14 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer WWW kingfisherfiber com Battery level and external power monitor The battery symbol has 4 levels TTTI 80 100 battery power remains TTE 40 80 battery power remains m 20 40 battery power remains i P Less than 20 battery power remains The LCD symbol Th shows external power is connected and battery charging initiated Please remove any alkaline batteries when connected to external power While charging the battery symbol will flash until the batteries are fully charged after which it will enter trickle slow charging mode Avoid leaving the instrument on charge for longer than 24 hours The instrument can be used whilst charging external power is connected For rechargeable batteries if less than 20 power remains to avoid reducing the rechargeable batteries lifetime the instrument should be turned off and the batteries charged User Manual KI 6103 Optical PON Power Meter Issue 2 15 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer WWW kingfisherfiber com Instrument maintenance and calibration General maintenance Avoid hard material making contact with the optical adaptors Keep adaptors clean at all times Keep the instrument in a dry place avoid moist
6. e set key USB port DC power supply socket Charging indicator User Manual KI 6103 Optical PON Power Meter www kingfisherfiber com Issue 2 4 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer www k ingfisherfiber com Install Batteries Warning To avoid damage to the instrument do not mix different types of batteries 1 Press in the direction of the arrow 2 Open the battery compartment cover 3 Place batteries correctly 4 Press down until the cover clicks into place User Manual KI 6103 Optical PON Power Meter Issue 2 5 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer In Line Test Setup Optical Splitter ONU Data Networks Analyser IXIA Smartbits CQ Fiber OLT PON C type average power test diagram User Manual KI 6103 Optical PON Power Meter www kingfisherfiber com Issue 2 6 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer Data Networks Analyser Optical Splitter IXIA Smartbits 1490nm Imi Lamda Lamda ONU Demultiplexer Multiplexer Variable Optical Attenuator ok 195th T co Vii O OLT Optical power sensitivity test diagram User Manual KI 6103 Optical PON Power Meter www kingfisherfiber com O Issue 2 7 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer WWW kingfisherfiber com Power Auto off battery saving function To Turn On Press the ON OFF key The instr
7. e warning if the signal level is close to the fail specification 3 FAIL if the signal level fails the specification For the LED indicators 1 Green means PASS 2 Orange means WRNG warning 3 Red means FAIL User Manual KI 6103 Optical PON Power Meter Issue 2 10 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer www k ingfisherfiber com Optical Power Reference Setting The instrument can be operated in Absolute dBm and Reference dB mode To set the Reference at all wavelengths Press REF Enter for gt 2 seconds the instrument will beep indicating that the reference is set and display the relative values in dB To toggle between dB and dBm short press the dB dBm key User Manual KI 6103 Optical PON Power Meter Issue 2 11 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer Threshold setting www kingfisherfiber com Th Mo L49801 m The threshold settings permit fast assessment of a links Pass Fail status There are 10 threshold Pass Fail data memory locations numbered 1 10 e To enter the threshold setting area press Threshold e To toggle between the threshold memory locations press Up or Down e To select a threshold memory location press REF Enter e To exit the threshold setting area press Threshold Tho Unit 1318n FALT 3 4 WWRAG 26 H FALT 38 4 When entered the threshold area displays the threshold number 1
8. ument will turn on and automatically zero and self calibrate e For power saving the instrument automatically turns Off 10 minutes after the last key press e To defeat the Auto Off feature Press the ON OFF key for gt 2 seconds until PERM is displayed on the LCD To turn Off Press the ON OFF key User Manual KI 6103 Optical PON Power Meter Issue 2 8 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer WWW kingfisherfiber com Optical Power Measurement nn j E RH The instrument can measure upstream 1310 nm and downstream 1490 1550 nm PON power levels When connected to a live PON network the instrument displays the 3 channel power level e If the power level is too high it displays HI e If the power level is close to but higher than the LO level WRNG is displayed to warn the user e If the signal is too low it displays LO User Manual KI 6103 Optical PON Power Meter Issue 2 9 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer Using LED indicators for fast Pass Fail assessment www kingfisherfiber com au 1490nm 1550nm ONT OLT Video oO Oo O The instrument uses LED indicators for fast Pass Fail assessment according to the threshold settings which can be pre set per wavelength Press F P mode the instrument displays the following according to the threshold setting 1 PASS if the power level meets the specification 2 WRNG to giv
9. ure Remove the batteries when storing the instrument for long time Calibration period Recommended once a year calibration if the instrument is used in the field Recommended once every two years calibration if the instrument is used in the laboratory User trouble shooting Problem Reason Method Check if the batteries are Fails to turn On Batter y properly installed Immediately turns itself B heck th h level Fails to charge the Check if the batteries are Battery batteries rechargeable batteries Error display Turn Off and then turn On pipe ISC DA Firmware Turn Off and then turn On to operate User Manual KI 6103 Optical PON Power Meter Issue 2 16 of 17 INTERNATIONAL Fiber Optic Test Equipment Manufacturer Specifications 1310nm upstream measurement Pass zone Measurement range Max power input Isolation 1490 1550nm 1490nm downstream measurement Pass zone Measurement range Max power input Isolation 1310nm Isolation 1550nm 1550nm downstream measurement Pass zone Measurement range Max power input Isolation 1310nm Isolation 1490nm Connector interface Fiber type Connector interface Measurement accuracy Uncertainty Polarization Return Loss Linearity Insertion Loss General Display Show Results Display Accuracy Backlight function Battery Type Battery Life Auto off function External power supply Temperature Storage temperature Relative humidity Size Weight
Download Pdf Manuals
Related Search