T9550 LCK - Pager.net
Contents
1. Dry Erase Server Board 1 10VAC 2A power supply charger 1 Velcro strip for mounting Installation Procedure The following is the basic installation procedure Y CAUTION e Do not connect any other devices to the transmitter e The transmitter requires a dedicated power supply Mounting the keypad antenna near any large metal objects will minimize the operating range NOTE The keypad should be charging whenever not in use Unwrap all system components Locate the silver connector located on the top of the transmitter unit Twist the antenna about 3 long onto the connector 3 Plug the power adapter charger into a standard 110V outlet and insert the barrel connector end into either of the side holes on the transmitter unit RA Press hold for 5 seconds and release the power reset button located on the side of the trans mitter unit The keypad display will light 5 Within 5 10 seconds the display light will disappear signifying that the transmitter is charging The display screen will be blank 6 Upon completion of setup allow the keypad to fully charge for at least 12 hours before use Be sure that pagers are also fully charged Mounting The transmitter unit can be mounted onto a wall surface e Use the Velcro mounting strip to mount the transmitter unit Be sure to mount the unit close to a standard 110 V power outlet Portable Use The transmitter is rechargeable and can be used without t2. longer than 30 days will have a negative impact on the life of the batteries requiring them to be replaced thus voiding the warranty If this product should become defective within the warranty period we will repair or replace it with an equiv alent product free of charge LRS will return your product via UPS ground shipping All warranty claims must be initi ated through our customer service department Customer Service 800 437 4996 4550 Excel Parkway Suite 200 Addison TX 75001 This warranty gives you specific legal rights and you may also have rights that vary from state to state Copyright O August 2008 Long Range Systems Inc All Rights Reserved This manual contains proprietary information of Long Range Systems Inc LRS and is intended for use only by its em ployees or customers None of the material contained herein may be copied reproduced republished downloaded dis played posted or transmitted in any form or by any means including but not limited to electronic mechanical photocopying recording or otherwise without the prior written permission of LRS Additional copies of this manual may be obtained by contacting LRS Screen displays keyboard layouts hardware descriptions or software are proprietary to LRS and are subject to copy right and other intellectual property rights of LRS and shall be treated in accordance with the previous paragraph All attempts have been made to make the information in this document
3. the number you wish to assign to the pager Choose ff 1 899 5 Press PROG 6 After the pager completes one glow mode cycle page it to ensure that it s programmed correctly See Basic Paging Operations pg 6 7 Repeat Steps 2 through 6 for each pager to program System Specifications Notice Operation is subject to the following e This device may not cause interference e This device will accept any interference including interference that may cause undesired oper ation of the unit T9550 LCK Required Voltage One 110V outlet for the transmitter keypad Operating Frequency 467 750MHz Radiated Power lt 4900 micro volts meter Operating Range Dependent upon the paging environment Rechargeable Pager Required voltage 1 110V outlet for 10VAC pager charger adapter Batteries Rechargeable Nickel Metal Hydride NiMH Battery life of pager Approximately 48 hours dependant on usage Recharge time 12 hours mini mum from completely dead Long Range Systems 8 T9550 LCK User Manual Troubleshooting Transmitter Unit The Light On The Keypad Display Does Not Come On When A Key Is Pressed e Perform a battery charge see pg 8 and check for a light after 30 minutes If the display still does not light check the charging power supply by plugging the power charg ing supply used for the pager charger into the transmitter unit If the display light comes on there may be a problem wit
4. T9550 LCK Paging System Transmitter GE Long Range Systems 800 437 4996 ag A pe VII ian A AA MI MI PM S Long Range Systems Inc 4550 Excel Parkway Suite 200 Addison TX 75001 800 437 4996 www pager net Table Of Contents Warranty so 5 id a a il ds a a a a ca li E 1 Long Range Systems 2 2 eee ee ee 2 General Information 2 000 eee ee 2 Basic Installation and Setup ooo ooo enerne 3 Hardware Provided ass rt a ee oe eee eke fade eee ee 3 Installation Procedure sci a mc e Lae ee eee Dee ae ee ee 8 3 Transmitted Keypad Elements 0 000 ccc arrene 4 Keypad Functions 600000 en nie cece el inne sie ncn teen ee cine a 4 Basic Paging Operation Guide an2uummmmm menu oo 5 FACING Va SE 5 Paging All Gall iman dot den cinder mete a b e eda sad we bebe 5 System Settings aie ii a a Se ene ske lc oe 6 Setting the Vibration Mode oocooccccccn een eee enas 6 System Reset o 6 Set Restaurant ID ga ret arar a o mee S ATE 6 Maintenance Functions oocooooooo ooo 7 Range Test siii sete Seen RE a Gad Reed Rae Te see Die 7 Check the Transmitter Battery Level 00 0 ccc eee eens 7 Battery Charge o ereed a ar hadd ar ar t 7 Programming Pagers 2 000202 eee eee es 8 System Specifications 0 000 meen enken es 8 TIBDO LOK cua rada a aa e da dd o ed A 8 Rechargeable Pagers icons res i
5. complete and accurate LRS is not responsible for any direct or indirect damages or loss of business resulting from inaccuracies or omissions Specifications and other information contained within this document are subject to change without notice Long Range Systems Inc reserves the right to make changes without further notice to any products herein LRS Inc makes no warranty representation or guarantee regarding the suitability of its products for any particular purpose nor does LRS Inc assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability including without limitation consequential or incidental damages Typical parameters that may be provided in LRS Inc data sheets and or specifications can and do vary in different applications and actual performance may vary over time All operating parameters including Typicals must be validated for each customer application by customer s technical experts LRS Inc products are not designed intended or authorized for use as components in sys tems intended to support or sustain life or for any other application in which the failure of the LRS Inc product could create a situation where personal injury or death may occur Should Buyer purchase or use LRS Inc products for any such unintended or unauthorized application Buyer shall indemnify and hold LRS Inc and its officers employees sub sidiaries affiliat
6. es and distributors harmless against all claims costs damages and expenses and reasonable attorney fees arising out of directly or indirectly any claim of personal injury or death associated with such unintended or unau thorized use even if such claim alleges that LRS Inc was negligent regarding the design or manufacture of the part de vice or system EU DECLARATION OF CONFORMITY We Long Range Systems hereby declare under our sole responsibility that the T9550 LCK paging transmitters and on site pagers comply with the essential requirements in the European RE amp TTE Directive 1999 5 EC of the European Par liament of the Council of 9 March 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity The following standards were utilized ETS 300 224 1998 EN 301 489 2 2002 EN61000 3 2 1998 EN 61000 3 3 1995 EN 60950 1992 with A1 A2 amp A3 AEE Long Range Systems 11 T9550 LCK User Manual
7. h the T9550LCK power charging sup ply Call LRS Customer Support to order a new power supply If the display still does not light there may be a problem with the transmitter unit Call LRS Cus tomer Support for assistance The Keypad Display Is Functioning Properly But The Pager Does Not Receive the Page e Perform a system reset see pg 7 e Complete the steps for paging a pager see pg 6 If the pager still does not receive the page call LRS Customer Support for assistance Pagers Pager Charge Lights Do Not Come On Pager charger should display a single red charge light when they are placed in the charger and are charg ing correctly If the red charge light is not visible on some or all charging slots review the following recom mendations to determine and solve the problem e Make sure the pagers are completely inserted into the charging slot e The power supply may be defective Try plugging the power supply used for the transmitter into the pager charger You may have more pagers charging on one power supply than recommended Only 25 pagers can be charged on one 10V power supply If you have more than 25 pagers you should call LRS to order additional chargers You may have a jumper wire that is not properly connected Look on the side of your chargers and verify that all wires are connected properly If they are connected then the metal contacts on your pager may be dirty Using a damp rag clean the 2 metal contact
8. he power supply e Disconnect the power supply from the transmitter unit to operate under battery power Be sure to plug the power supply back into the transmitter when not in use to recharge the battery Long Range Systems 3 T9550 LCK User Manual a Antenna Long Range Systems 800 437 4 Dry Erase Server Board 79550LcK T9550LCK 120VAC Electrical Supply Button Keypad Function Keys Transmitter Keypad Elements Power Reset Button Used when the transmitter s battery is either depleted or low and needs to be charged When pressed and released the power reset button ensures proper charging Dry Erase Server Board Write the staff names on the label next to their pager number with a NON PERMANENT Dry Erase Marker or grease pencil Keypad Functions Before using the keypad read the following key descriptions Number Keys The number keys 1 through 12 are one touch keys to instantly send a message to pagers num bered 1 12 Function Keys The function keys are located on the last row of the transmitter keypad PGR Used when entering pager numbers above 12 0 Used when entering pager numbers above 12 that contain a zero and when calling all pagers at once PROG Used to alter messaging modes and to check the battery level ENTER After entering pager numbers above 12 press ENTER to send the page Long Range Sys
9. he transmitter unit 2 Press PROG and then ENTER The unit will show a number from 0 to 5 If plugged in it does not matter If the unit shows 4 or above the charge is adequate for normal use If the unit shows 3 it is ok for short term use 1 2 hours If the unit shows 2 or less including blank it must be recharged before use Battery Charge If the battery power has been completely depleted 1 Plug the power supply charger into the transmitter unit 2 After 10 seconds press and release the power reset button located on the side of the transmitter The display will light 3 Within 5 10 seconds the display light will disappear and the screen will remain blank This is an indication that the battery is charging 4 Allow the keypad to charge for at least 12 hours 5 Check the battery level to ensure that the battery is fully charged see pg 8 Long Range Systems 7 T9550 LCK User Manual Programming Pagers Only LRS s Star Pagers can be reprogrammed from the T9550 LCK transmitter If you would like to assign or reassign numbers to pagers contact LRS to verify your restaurant ID before proceeding The following is the basic procedure for programming pagers 1 Be sure to set the LCK for the restaurant ID in use See Restaurant ID pg 7 2 Remove the pager from the charger and wait until it stops vibrating Note remove only one pager at a time during programming 3 Press PROG 4 Enter
10. i o to o e a becada 8 Troubleshooting oea 0 een a Sc eh wi eee eee ska ke Sa Sjel Gree 9 Transmitter Unik ocho Sete eras Sade b e es bade bades ta ead de 9 P gers serate da anaie ete A wares BAP Keke a eee 9 Service Questions and Answers ooooooooo eee eee 10 Warranty 5 ici a ee Rew a a ei ee ee ee ee Saka 11 Long Range Systems 1 T9550 LCK User Manual Long Range Systems Long Range Systems is a provider of cutting edge onsite paging solutions We offer exceptional products and services that satisfy our customer s needs for years to come Thorough familiarity with these instructions and procedures will ensure proper operation and maintenance of the system NOTE This guide should be kept readily available for managers and key staff General Information The T9550 LCK is an onsite paging system used to increase efficiency in operations by alerting key staff of immediate needs The pagers used with the system can vibrate once twice or three times NOTE The T9550 LCK only works with LRS Star Pagers a Y STAR PAGER 3 Al ad ES LED s o T9550LCK PGR 0 Prod ENTER mr Long Range Systems 2 T9550 LCK User Manual Basic Installation and Setup Hardware Provided Each T9550 LCK transmitter kit contains 1 Transmitter keypad 1 1 Antenna 1
11. mitter to factory default 1 Press PROG 2 Enter 0 0 O and press ENTER Set Restaurant ID NOTE The T9550 LCK is shipped factory defaulted in the most commonly used configuration e The Restaurant ID factory default setting is 0 Your system may or may not be shipped with the factory default setting ID 0 However this ID is often used except in cases where neighboring establishments both use LRS systems and would interfere with each other Contact LRS to verify your Restaurant ID It is not recommanded to change system ID without speak ing to LRS service departments To change the ID 1 Press PROG 2 Enter 9 0 EX 9 0 3 Restaurant ID 3 3 Press ENTER Long Range Systems 6 T9550 LCK User Manual Maintenance Functions Range Test Perform a range test to determine the furthest point a pager will receive the signal of the T9550LCK A NOTE Be sure to remove pagers from the charging base before performing the range test Press PROG 2 Enter 9 1 2 and press ENTER 3 When the 0 begins scrolling across the screen pagers will vibrate every 5 seconds as long as they are receiving the signal 4 Take a pager and walk around the area to verify that the pagers operate in all areas 5 When a pager stops vibrating every 5 seconds it is out of range and is no longer receiving a sig nal from the transmitter Check the Transmitter Battery level 1 Disconnect barrel end of the power adapter from t
12. s on the back of each pager Be sure that your staff is not disconnecting the power supply at anytime or that you do not have the charger connected to a circuit that automatically shuts off after hours The charging base should be plugged into a power outlet that is ON at all times Be sure the pager is not in the charger backwards If none of these recommendations solve your problem call LRS Customer Support to deter mine the problem at 800 437 4996 Long Range Systems 9 T9550 LCK User Manual Service Questions and Answers Should your paging system ever fail or should you need additional paging equipment call Long Range Sys tems at 800 437 4996 Normal Business Hours Monday Friday 8 30 am to 5 00 pm Central Time Weekend or Evening Emergencies Long Range Systems provides 24 7 live technical support e Please keep in mind that replacement options are limited on weekends and holidays Long Range Systems 10 T9550 LCK User Manual Warranty Long Range Systems Inc warrants this product against any defects that are due to faulty material or workmanship for a two year period after the original date of consumer purchase The warranty does not include damage to the product re sulting from accident misuse improper electrical connection or failure to charge the product within 30 days of receipt Rechargeable pagers are required to stay on charge while not in use Rechargeable pagers that are left off of charge for
13. tems 4 T9550 LCK User Manual Basic Paging Operations NOTE The T9550 LCK factory defaults are the most commonly used settings All units are set to vibe 1 time as the default Paging For pagers numbered 1 12 1 Press the pager number 2 The unit will automatically send a page For pagers numbered 13 and higher 1 Press PGR 2 Enter the pager number using the 0 9 keys 3 Press the ENTER key Page All Call If all staff pagers need to be called simultaneously 1 Press PGR 2 Press0 0 0 3 Press the ENTER key Long Range Systems 5 19550 LCK User Manual SYSTEM SETTINGS Setting the Vibration Mode Vibration mode determines the number of times a pager will vibrate when paged A NOTE The factory default setting for vibration mode is 1 vibration EX When a page is sent from the transmitter the pager will vibrate once To set the vibration mode use the following steps e 1 vibration Press PROG Enter 9 2 1 and press ENTER e 2 vibrations Press PROG Enter 9 2 2 and press ENTER e 3 vibrations Press PROG Enter 9 2 3 and press ENTER e Page a pager see pg 6 to ensure that the pager vibrates the number of times programmed System Reset If the transmitter s battery has been completely depleted it may require a system reset before operating properly When the system is reset the Restaurant ID see pg 7 and vibration mode see pg 7 will be set to factory default To reset the trans
Download Pdf Manuals
Related Search