Terminus GSM864Q User Guide R08.pmd
Contents
1. Its characteristics are as follows Audio Input Circuit Mic e Line Coupling AC e Line Type Balanced e Coupling Capacitor gt 100nF e Differential Input Resistance 50kQ e Differential Input Voltage lt 1Vp p 865Vrms e Nominal Input Sensitivity 45 dBVrms Pa Audio Output Circuit Earpiece or Speaker e Line Coupling DC e Line Type Bridged e Output Load Resistance gt 14Q e Frequency Response 150 4000 Hz 3dB e Differential Output Voltage 328mVrms 16Q 12 dBFS e Software Volume Control 2dB step 10 steps total 4 3 2 Pin Out 4 Mic 3 Earphone 2 Earphone 1 Mic 4 3 3 Signal Description Pin Description o_o Microphone 2 Earphone 3 Earphone 4 Microphone 3 0Vdc nominal supplied by Terminusto power handset Terminus Hardware user Guide GSM864Q Page9 Rev 08 Date 07 23 08 J AN U S REMOTE Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice C MMUNICATI NS 4 Interfaces continued 4 4 Embedded Interface 4 4 1 Description The Embedded Interface is a 50 pin straight header that allows a user to access many of the available ports and features of the Terminus through a single interface The connector is located on the bottom of the unit such that it can be integrated with an application PC board A ribbon cable with a tabbed header connector such as the Samtec HCSD 25 D 1 can also be used This interface can be f2. Pin Description Center Pin GPS Signal 3 7 Vdc nominal supplied from Terminus to power active antenna Outer Conductor Signal ground Note GPS Antenna Interface only available by option otherwise not populated 4 6 3 2 GPS Active Antenna Specifications Input Voltage Range 3 4 to 4 2 Vdc Frequency range 1575 42 3 MHz Gain Depends on cable type and length Impedance 50 ohm VSWR lt 1 5 1 Note GPS Antenna Interface only available by option otherwise GPS Antenna not required 4 6 3 3 GPS Antenna Installation Guidelines 1 Install the antenna with a clear sky view 2 Antenna shall not be installed inside metal cases 3 Antenna shall be installed also according to Antenna manufacturer instructions 4 7 SIM Card Interface 4 7 1 Description The SIM Card Interface allows the Terminus to accept the subscriber card provided by the cellular telephone provider It can accommodate a 1 8V or 3 0V SIM card and complies with the GSM 11 14 Phase 2 SIM Toolkit standard Card Reader access JAN U S Terminus Hardware user Guide GSM864Q Page 14 Rev 08 Date 07 23 08 REMOTE C MMUNICATI NS Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice 5 TECHNICAL SPECIFICATIONS 5 1 Electrical Specifications 5 1 1 GSM Module Specification e Quad band EGSM 850 900 1800 1900 MHz e Output Power Class 4 2W 850 900 MHz Class 1 1W 1800
3. CD OUTPUT RS 232 2 Received Data RxD OUTPUT RS 232 3 Transmitted Data TxD INPUT RS 232 4 DTE Ready DTR INPUT RS 232 5 Signal Ground N A N A 6 DCE Ready DSR OUTPUT RS 232 7 Request to Send RTS INPUT RS 232 8 Clear to Send CTS OUTPUT RS 232 9 Ring Indicator RI OUTPUT RS 232 Terminus Hardware user Guide GSM864Q Page7 Rev 08 Date 07 23 08 JANUS ee more Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice C MMUNICATI NS 4 Interfaces continued 4 2 Power Supply 4 2 1 Description The Terminus Power Supply jack accepts input voltages from 7 to 18 VDC optionally 7 to 40 VDC for V3 00 and V4 00 models and requires a nominal current sourcing capacity of 5W maximum 10W This jack accepts a barrel type plug with a receptacle for a 2 1mm center conductor 4 2 2 Pin Out e 4 2 3 Power Supply Interface Pin Description Center Pin Supply Outer Conductor Supply JANUS Terminus Hardware user Guide GSM864Q Page8 Rev 08 Date 07 23 08 REMOTE COMMUNICATIONS Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice 4 Interfaces continued 4 3 Audio Interface 4 3 1 Description The Terminus audio interface is designed to accommodate a telephone handset with a 4P4C modular plug The input circuit supports a balanced low impedance microphone and can supply a bias voltage of 3 0 VDC
4. Ii i I it Zs A A 2x Hole or 6 SHCS zr Bottom View w Bottom Cover Removed 1 214 30 84 o 3 750 i 313 95 25 7 95 2 600 66 04 2 369 60 18 2 600 66 04 2 357 59 86 2 369 60 18 2 152 54 65 2 304 58 52 2 143 54 44 E a oletat 2 204 55 98 2 143 54 44 2 050 52 07 LJ OCJ CJl 550 13 97 550 13 97 olo olo 140 3 56 I ia 1 f I lf 2x 28 A 2 or Q tre E Clearance for a Oo 8 N oO Bo g O BAe OR ql 6 SHCS io I IQS jee Te Res g gt 8 G mT 140 3 56 BAe eee ea a 2x O O M N Clearance for a _ 7 SHCS Mechanical Dimensions an Top View Mechanical Dimensions Top View 070 1 78 2 400 60 96 T B 2 400 60 96 I 100 2 54 Pin 50 l Pin 2 Pin 50 Pin 2 k Pin 49 Pin 1 Pin 49 Seer a yar eget ree eee eae 050 1 27 040 1 02 100 2 54 340 8 64 100 2 54 Pad Dimensions for Hole eg els for recomended connector recomended connector Samtec P N SSW 125 22 S D VS Samtec P N SSQ 12
5. PWRMON Pin PWRMON PIN Output Logic State Description 0 Terminus powered down 1 Terminus powered on Notes 1 Used in conjunction with ON OFF pin to control power on and power down state 4 4 4 6 UART_SEL Pin UART_SEL PIN Input Logic State Description 1 Terminus UART interface routed to DB9 connector RS 232 0 Terminus UART interface routed to EMBEDDED connector 2 8V_CMOS J AN U S Terminus Hardware user Guide GSM864Q Page 12 Rev 08 Date 07 23 08 REMOTE C eMMUNICATIONS Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice 4 Interfaces continued 4 5 LED Status Indicators Status Indicator 4 5 1 Description The LED Status Indicators are located on the top of the housing near the end where RR CR the antenna jacks are There are 2 LED indicators GSM Status and GPS Status 4 5 2 GSM LED Status Yellow LED Status Device Status Permanently Off Device Off Fast Blinking 0 5 sec on 0 5 sec off Net search Not registered Turning Off Slow Blinking 0 3 sec on 2 7 sec off Registered Full Service Permanently On A call is active 4 5 3 GPS Green LED Status Device Status Permanently Off Device Off Blinking Receiver Activated RF Interface 4 6 RF Interface 4 6 1 Description There are two RF interfaces on the Terminus the GSM antenna jack and the GPS antenna jack the non GPS version will only have o
6. 1900 MHz e Control via AT commands according to GSM 07 05 07 07 and proprietary Telit e Serial Port Multiplexer GSM 7 10 e TCP IP stack access via AT commands e Sensitivity 107 dBm type 850 900 MHz 106 dBm typ 1800 1900 MHz 5 1 2 GPS Module Specifications GPS Channels 16 Frequency 1575 42 MHz L1 C A Code TTFF Cold Start 135 dBm 46 seconds i7 TTFF Warm Start 141 dBm 34 seconds 1 7 TTFF Hot Start 141 dBm 5 seconds 1 7 Re acquisition time 147 dBm lt 3 seconds Acquisition Sensitivity fix not available TTFF Hot with all signals at 138 dBm 30s TTFF Hot with all signals at 141 dBm 41s Acquisition Sensitivity fix available dBm 147 dBm Tracking Sensitivity dBm 150 dBm Acquisition Sensitivity SBAS satellites dBm 135 dBm 6 143 dBm Static Accuracy without SBAS 50 Confidence CEP 1 2m 7 95 Confidence 3 1 m Static Accuracy with SBAS 50 Confidence CEP 0 8 m 8 95 Confidence 2 0 m Maximum Horizontal Speed 515 m s 9 Maximum Vertical Speed 15 m s 10 Maximum Altitude 18 Km 11 Maximum Acceleration g 2g Notes 1 These are RMS values 7 Open sky 24 hrs statistic active antenna signal range is 2 Maximum Sensitivity 147 dBm between 30 to 49 dB Hz 3 Simulator Test all signals at specified power level 8 Open sky 24 hrs statistic active antenna EGNOS signal used 4 Estimated 9 Limited by International Traffic in Arms Regulat
7. 5 XX X D Top View Top View Recommended Surface Mount Footprint Recommended Thru Hole Footprint Terminus Hardware user Guide GSM864Q Page 17 Rev 08 Date 07 23 08 J AN U S REMOTE Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice C MMUNICATI NS 6 OPERATION 6 1 Setting Up a Terminus Emulator 6 1 1 To interface with the Terminus connect the Serial Interface RS 232 port to a PC and use a terminal emulation program such as Microsoft Hyperterminal Set the interface parameters as follows e Baud Rate 115 2 kbps e Bits 8 e Stop Bits 1 e Parity None e Hardware Handshaking Yes 6 1 2 Set Terminus to Auto bauding e Enter AT lt cr gt from terminal and wait for OK e Enter AT IPR O lt cr gt and wait for OK e Terminus is now set for auto data rate detection 6 2 Powering ON Off 6 2 1 The Terminus is turned ON automatically once DC power is applied If the Terminus is turned OFF using one of the methods described below it can be turned back ON again through one of two methods e pull ON OFF signal pin 3 of 50 pin straight header to ground then release e press the ON OFF switch then release The Terminus ts fully operational after 4 seconds Logging onto a network may take longer than this and is outside the control of the Terminus 6 2 2 There are three ways to switch OFF the Terminus as described below e Use the appropriate AT command AT SHDN e Pull ON OF
8. D INPUT 2 8V_CMOS 2 45 Received Data RxD OUTPUT 2 8V_CMOS 47 GPS_TxD OUTPUT 2 8V_CMOS 2 49 Transmitted Data TxD INPUT 2 8V_CMOS 2 4 6 8 Supply 7 18 VDC N A N A 10 12 14 16 18 Supply GND N A N A 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 Notes 1 It is recommended that this input be controlled by an Open Collector Drain output Do not use an external pull up resistor a pull up is included internal to the Terminus 2 This signal is only available by option otherwise No Connection 4 4 4 Signal Details 4 4 4 1 General Purpose Input Output Terminus GPIO are configurable as input output and special function Configuration is controlled by the Customer specific application via AT commands send on the UART interface The following table describes GPIO configuration options GPIO Configuration Alternate Function 1 Input Output 2 Input Output 3 Input Output 4 Input Output 9 Input Output RFTX monitor output 6 Input Output alarm output r4 Input Output buzzer output 8 Input Output 9 Input Output Terminus Hardware user Guide GSM864Q Page 11 Rev 08 Date 07 23 08 JANUS temor Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice C MMUNICATI NS 4 Interfaces continued 4 4 4 Signal Details continued 4 4 4 2 Analog to Digital Converter ADC Description 1 Analog to Digital Converter In
9. DICES 7 1 Approvals 7 1 1 PTCRB Certification The Terminus is PTCRB Certified Lab Cetecom Inc Date 7 27 2007 7 2 Safety Recommendations for Information only 7 2 1 General Your Terminus GSM864Q Terminus terminal is based on the GSM standard for cellular technology This standard is universal and covers Europe Asia United States and Africa which is the most used telecommunication standard Your Terminus is a low power radio transmitter and receiver It sends out and receives radio frequency energy When a GSM application is used the cellular system that handles your calls controls both the radio frequency and the power level of your cellular wireless CPU 7 2 2 Exposure to RF Energy There is public concern about possible health effects of using GSM terminals Although past research on health effects from RF energy has focused on the current RF technology scientists have begun researching newer radio technologies such as GSM After existing research has been reviewed and after compliance to all applicable safety standards has been tested the conclusion is that the product is fit for use 7 1 3 Antenna Care and Replacement Do not use the Terminus with a damaged antenna If adamaged antenna comes into contact with the skin a minor burn may result If you have a damaged antenna refer to the instruction manual provided for proper procedures Or have your antenna repaired by a qualified technician Buy the antenna from an
10. F signal to ground then release e Press ON OFF switch SW1 then release 6 3 Setting Up Service Network Settings 6 3 1 The network settings for the Terminus will vary depending on the cellular carrier you are using Below are two of the North American Cases for these settings For T mobile amp MNVO Raco Sensor Logic Nexaira Jasper Wireless enter AT SELINT 2 use of most recent AT command set AT STIA 2 10 or AT STIA 1 enable SAT SIM Application Tool Kit AT BND 3 default bands to 850 1900 AT AUTOBND 1 enable Quad band system selection AT PLMNMODE 1 enable EONS enhanced operator naming scheme AT amp PO save profile AT amp WO save setting For AT amp T Cingular amp MNVO Kore Aeris nPhase enter AT SELINT 2 use of most recent AT command set AT ENS 1 AT amp T Cingular configuration SAT BND AUTONBND PLMNMODE plus Cingular specific ENS requirements If Terminus is being used in a different country or with a different carrier please refer to Telit AT Command refer ence document regarding the use of the AT BND command to set the proper frequency band Important After entering either of the sets of settings above power the Terminus OFF and then ON It is now ready for use 6 3 2 Check network status assuming you have a valid SIM card installed Enter AT CREG lt cr gt And wait for response Response will be CREG 0 1 or CREG 1 1 meaning device is registered on its home ne
11. GDCONT 1 IP APN 0 0 0 0 0 0 lt cr gt where APN is specific to the service provider being used e Enter AT CGQMIN 1 0 0 0 0 0 1 This sets the minimum Quality of Service profile e Enter AT CGQREQ 1 0 0 3 0 0 1 This sets up the desired Quality of Service profile e Enter AT SGACT 1 1 v p where v is your user ID and p is your password If these are not set replace with 1 This activates the PDP context e Enter AT SD 1 0 IPA Port 0 0 1 Look for response CONNECT This opens a remote connection via socket 2 IPA the IP address given to you by your service provider in the format XXX XXX XXX XXX 3 Port the remote host port to contact provided by carrier 0 to 65535 e At this point a data session is active and data can be sent from the Terminus to the remote device and visa versa 1 To exit the data session send the characters and wait for the OK response e Enter AT SH 1 to close the socket 6 7 Further Instructions On utilizing different commands for other applications than those described here please refer to the following documents Telit AT Commands Reference Guide Telit GC864 Software User Guide Telit Easy GPRS User Guide Terminus Hardware user Guide GSM864Q Page 19 Rev 08 Date 07 23 08 J AN U S REMOTE Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice C MMUNICATIONS 7 APPEN
12. Terminus GSM864Q Hardware User Manual Issue R08 JANUS ee mor C MMUNICATI ONS TABLE OF CONTENTS TABLE OF CONTEN eee meee nee ee Bee ee me eer ne ey Sse eer eer eee nen eres eer a oeee en ee rer 2 3 ro CANER cag ec ees ec mee E E ree reece seen eee ea ace ee cecdene cee 3 2 PEFERERN E rem pe ee NO CP EA EP RB ester eerie eee eee eee 4 2 1 Telit Document List 2 2 Janus Document List S OVERVIEW sirnirseente een E A AE O E A EE A 4 6 3 1 Introduction x cceiscorccnciccdsesicoctddascadasSataiasend Sueiecasseddoianrenciaiaddaiadcacsialcadeieadiadecsbddenadeeasiccedeieeasetadetecdied 4 3 2 Funcional SSCLIONOMN sssri aE e iaei Es 4 3 2 1 Connectors x ccnancsvandcnamenanssakcncosnunatsnncdagamdaweniowwalnedodaanehaumsnasmensencudlnnsinnuicadasnaidcaws weamncibuemeniedmenanmsmaineiman 4 oaae OG Da a ena EEE E A EEEO E 5 S FO a E E 6 INTERPA E ardaoa EEA EEN EEEE EAEE 7 14 4 1 Serial Interface Connector cc ccucsccnenavscvwcaccsiancinonnssonrandatoupoewadedwdeavbewndwoubiuediduentaundaidensoescedoeiadeecuanetacs 7 4 1 1 Description 4 1 2 Pin out 4 1 3 Signal Interface Description i POW TI ee e E a E 8 4 2 1 Description 4 2 2 Pin out 4 2 3 Power Supply Interface 4 3 PIG ON SMC Soccer artaes da tee seceataeocns ganteeetencdseancusoace danemonneots aka aaa aeaii ianari 9 4 3 1 Description 4 3 2 Pin out 4 3 3 Signal Description 4 4 Embedded Interface vsscsmccwoinncarsceanmivanckenieustnndesdacdcaatwaasansaadsih netaacaiedcetensai
13. Typical Current Source Sink capability 1mMA 1UA Recommended Operating Conditions RESET pin Parameter Min Typ Max Unit Input Voltage High Vih_rst 2 0 2 2 Volt Input Voltage Low Vil_rst 0 0 2 Volt It is recommended that this input be controlled by an Open Collector Drain output Do not use an external pull up resistor a pull up is included internal to the Terminus Recommended Operating Conditions ADC1 pin Parameter Min Typ Max Unit Input Voltage Range 0 2 Volt AD Conversion 11 Bits Resolution 1 1 lt 1 mV 5 1 4 Terminus Electrical Specifications Power Supply Min Typ Max Unit Note Voltage Range 7 18 VDC Current idle mode 14 22 mA typ 3 Current idle mode with GPS 20 35 mA typ 3 4 Power max 11 5 Watts 5 Note 1 7 40V Vin by option Please contact a sales representative for more information about ordering Terminus with GPS option 2 Max current draw of 25mA on the 3 165VDC output 3 Registered on Network No Traffic 4 Active antenna not connected 5 Maximum power during GSM transmission see Telit GC864 Hardware User Guide Section 5 1 for more information Terminus Hardware user Guide GSM864Q Page 16 Rev 08 Date 07 23 08 JANUS REMOTE C MMUNICATIONS Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice 5 Technical Specifications continued 5 2 3 GC864Q Mechanical Dimensions Hl
14. approved suppliers list Using unauthorized antennas modifications or attachments could damage the Terminus and may violate local RF emission regulations or invalidate type approval 7 3 Abbreviations AC Alternating Current GSM Global System Mobile ADC Analog To Digital Converter ITAR International Traffic In Arm Regulation BER Bit Error Rate LED Light Emitting Diode CD Carrier Detect M2M Machine To Machine CSD Circuit Switched Data PBCCH Packet Broadcast Control Channel CTS Clear To Send PDU Protocol Data Unit DB Decibel RF Radio Frequency DBFS Decibels Full Scale RI Ring Indicator DC Direct Current RSSI Received Signal Strength Indication DCE Data Communications Equipment RTS Request To Send DSR Data Set Ready RxD Received Data DTMF Dual tone multi frequency SMS Short Message Service DTR DTE Ready TTFF Time To First Fix EGNOS European Geostationary Navigation Overlay Service TxD Transmitted Data FDN Fixed Dialing Number USSD Unstructured Supplementary Service Data GPIO General Purpose Input Output VSWR Voltage Standing Wave Ratio GPRS General Packet Radio Service WAAS Wide Area Augmentation System J AN U S Terminus Hardware user Guide GSM864Q Page 20 Rev 08 Date 07 23 08 REMOTE C MMUNICATIONS Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice 7 APPENDICES continued 7 4 Ordering Information Ordering Information Description GSM864Q V1 00 Terminu
15. ion ITAR 5 Simulator Test continuous fix with all signals at specified power level 10 Defined by navigation integrity check 6 Simulator Test with signal at specified power level 11 Limited by International Traffic in Arms Regulation ITAR Terminus Hardware user Guide GSM864Q Page 15 Rev 08 Date 07 23 08 JANUS ee mors Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice C MMUNICATI NS 5 Technical Specifications continued 5 1 3 I O Level Specification Absolute Maximum Ratings Parameter Min Typ Max Unit Note VIN DIGITAL INPUTS 0 3 3 75V Volt VIN ANALOG INPUT 0 3 3 00V Volt Storage Temperature 40 85 C Supply referenced to Supply 0 24 V 1 Operation of the device at these or any other conditions beyond those listed under Recommended Operating Conditions is not implied Exposure to Absolute Maximum Rating conditions for extended periods of time may affect device reliability Recommended Operating Conditions Parameter Min Typ Max Unit Note Temperature 10 55 C Supply referenced to Supply 7 18V Volt 1 3 165 VDC Output 3 3 3V Volt 2 Recommended Operating Conditions Interface levels 2 8V CMOS Parameter Min Typ Max Unit Input Voltage High Vih 2 1 3 3 Volt Input Voltage Low Vil 0 05 Volt Output Voltage High Voh 2 2 3 0 Volt Output Voltage Low Vol 0 0 35 Volt
16. ll Broadcast m Fixed Dialing Number FDN m Text and PDU mode m Real Time Clock Circuit Switched Data Transmission m Alarm amp Battery Management m Asynchronous Transparent Circuit Switched m Network LED Support Data CSD up to 14 4 kbps m IRA Character Set m Asynchronous Non transparent CSD up to Jamming Detection amp Report 9 6 kbps m Embedded TCP IP Stack including TP m V 110 IP UDP SMTP and FTP protocol GPRS Data m GPRS Class 10 Mobile station class B m Coding Scheme 1 to 4 m PBCCH Support 3 3 2 GPS Features CW20 Delivers enhanced tracking to 152 dBm Low power consumption 19mA fully active 16 Channel Receiver Supports WAAS EGNOS Terminus Hardware user Guide GSM864Q Page6 Rev 08 Date 07 23 08 JANUS REMOTE C eMMUNICATIONS Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice 4 INTERFACES 4 1 Serial Interface Connector 4 1 1 Description The Terminus serial interface is an RS 232 port that supports both EIA TIA 232 and V 28 V 24 communications protocols It accepts a standard RS 232 Sub D 9 pin male plug Communications settings for this port are as follows e Baud Rate 115 2kbps e Bits 8 e Stop Bits 1 e Parity none e Hardware Handshaking Yes 4 1 2 Pin Out 6 DSR 7 TRS 8 CTS 9 RI 1 CD 2 RxD 3 TxD 4 DTR 5 GND 4 1 3 Signal Interface Description Pin Description I O Signal Type 1 Carrier Detect
17. nals are MIXED between the 50 PIN and DB9 connector All other UART connections are shared between the 50 PIN and DB9 connector Hardware Handshaking signals can only be used if either the 50 PIN or DB9 connector is connected exclusively Shared UART connections are all inputs so no I O contention will occur 3 CMOS Signals Include CTS DTR DSR RING DCD 4 Zero Ohm resistor placed only on Python enabled versions Terminus Hardware user Guide GSM864Q Page5 Rev 08 Date 07 23 08 J AN U S REMOTE Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice COMMUNICATIONS 3 OVERVIEW continued 3 3 Terminus Features 3 3 1 GSM Features Audio Fax m Telephony Emergency m Group 3 Class 1 m Half rate Full rate Enhanced Full rate and Adaptive Multi Rate voice codecs HR FR GSM Supplementary m Call Forwarding EFR AMR m Call Barring m Superior Echo Cancellation amp Noise m Call Waiting amp Call Hold Reduction m Handset amp Hands free operations sigs a a DTMF a maui Line Identification Presentation Clip Approvals Calling Line Identification Restriction m Fully type approved according to R amp TTE CLIR m CE GCF FCC PTCRB IC m Unstructured Supplementary Services SMS Mobile Originated Data USSD Point to Point mobile originated and mobile m Closed User Group terminal SMS Additional Features m Concatenated SMS supported m SIM Phonebook m SMS Ce
18. nasanensanindenine dopononacnnieadnacadddaionivadicedabtddandennaneiines 17 C OFE RATON oarn E AES 18 19 6 1 Setting Up a Terminus Emulator sccaedinceeesacessndesiesiseeceueeaveadierseecusrenaiecceandsndecnocbcusnececeessStavioecsueseevians 18 62 POwernng ON OFP siereicerareio a ne n n e a ee ee ere eee e ia 18 6 3 Setting Up Network Services ccccccccscsssssseeccceeeeceeceeeeeseeceeceeeeeeseaeeeesseeeeeeeeeeesaeaueeseeeeeeeeeeseeaaas 18 6 4 Make a Voice Call oo cccccceeeccecccceeeeeseeeeeecseeceeeeeeeeeseaeaeeeeeeeeeeeeeseeeeseesceeeeeeeeessaeauaaeeeeeeseeeseneaaas 19 6 5 Making an SMS Call 2 0 cccccccsccessescccceesecccceceeasseseeeseeesccecesdeuusnescceescnccccccusesenneeeeeessecceceesasssenees 19 6 6 Making a GPRS Data ae sesh ceeds ce aiaa aa a r eE eai Eai Seia 19 6 7 Reference to documents ccccceeccccceseecceceeeecceeceeeeeeceuseeeeseaeeceeeseseececsuaeeeessaeeceeeseeeeessaeseeesaaaeess 19 De FPENDICES eisrean a i vetelandassniaininapanabaedaancessuneiniautioneiins 20 22 7 1 Approvals 7 2 Safety 7 3 Abbreviations 7 4 Ordering Information 7 5 Revision History 1 DISCLAIMER The information contained in this document is the proprietary information of Connor Winfield Corporation and its affiliates Janus Remote Communication The contents are confidential and any disclosure to persons other than the officers employees agents or subcontractors of the owner or licensee of this document without the prior written consen
19. ne The specifications and Ss ft requirements for these are as follows GPS GSM i L 4 a Jack Jack 4 6 2 GSM Antenna 4 6 2 1 GSM Antenna Interface Type SMA FEMALE Pin Description Center Pin GSM Signal Outer Conductor SIGNAL Ground 4 6 2 2 GSM Antenna Specifications Frequency range Depending by frequency band s provided by the network operator the customer shall use the most suitable antenna for that those band s Bandwidth 70 MHz in GSM850 80 MHz in GSM900 170 MHz in DCS 140 MHz PCS band Gain lt 3dBi Impedance 50 ohm Input power gt 2 W peak power VSWR absolute max lt 10 1 VSWR recommended lt 2 1 Terminus Hardware user Guide GSM864Q Page 13 Rev 08 Date 07 23 08 JANUS cemore Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice C MMUNICATIONS 4 Interfaces continued 4 6 RF Interface continued 4 6 2 GSM Antenna continued 4 6 2 3 GSM Antenna Installation Guidelines 1 Install the antenna in a place covered by the GSM signal 2 The Antenna must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located or operating in conjunction with any other transmitting antenna 3 Antenna shall not be installed inside metal cases 4 Antenna shall be installed according to manufacturer instructions 4 6 3 GPS Antenna 4 6 3 1 GPS Antenna Interface Type MCX FEMALE
20. put 4 4 4 3 Reset Pin RESET PIN Input Logic State Description High Z Terminus Active State 0 Terminus Reset State Notes 1 It is recommended that this input be controlled by an Open Collector Drain output Do not use an external pull up resistor a pull up is included internal to the Terminus 2 The RESET pin is offered as a means to reset the Terminus when and if the Terminus becomes unresponsive The RESET pin is not intended to be used as a means of turning the Terminus off Use the ON OFF pin to turn the Terminus on or off 3 RESET state must be held for at least 200ms before returning to active state 4 4 4 4 ON OFF Pin ON OFF PIN Input Logic State Description High Z Terminus turned ON or OFF after Input returns to this state 0 Toggle Terminus ON or OFF Notes 1 It is recommended that this input be controlled by an Open Collector Drain output Do not use an external pull up resistor a pull up is included internal to the Terminus 2 The ON OFF pin is offered as a means to power on and power down the Terminus When the Terminus powers down it informs the cell tower that it is powering down and will not be communicating with the tower any more This is considered a controlled power down 3 After toggling the power state of the Terminus wait until PVRMON indicates chosen state before toggling the power state again 4 Optionally the Terminus may be powered down with the use of AT commands 4 4 4 5
21. re User Guide 2 1 3 80000ST10025a AT Commands Reference Guide 2 1 4 80000ST10028 Easy GPRS User Guide 2 2 Janus Document List Please refer to the Janus website www janus rc com for the latest product information on the Terminus and the CW20 GPS Module 2 2 1 NavSync CW20 CW20S GPS Receiver User Manual Bulletin NS25 3 OVERVIEW 3 1 Introduction The Terminus GSM864Q is a self contained quad band GSM GPRS terminal device designed to provide a comprehensive solution to application problems for our M2M customers It utilizes the proven technology of the Telit GC864 Quad module for its core communications engine as well as the NavSync CW20 module for the added flexibility of GPS 3 2 Functional Description 3 2 1 Connectors Access Panel for SIM card reader Header Pin access Power ff R5232 Serial VO Interface wee MCX ecm SMA Connector Audio Connector GPS Reciever GSM input Antenna Connectors JAN U S Terminus Hardware user Guide GSM864Q Page4 Rev 08 Date 07 23 08 REMOTE C MMUNICATIONS Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice 3 OVERVIEW continued 3 2 2 Block Diagram ON OFF EXTERNAL ADC PIO 1 9 RESET PWRMON 50 PIN EMBEDDED INTERFACE PIO18 GPS RESET PIO19 GPS WAKEUP Note 1 RS 232 Signals Include RxD TxD CTS RTS DTR DSR RING DCD 2 Only the RxD TxD and RTS CMOS sig
22. s GPS Terminal GSM864Q V2 00 Terminus Non GPS Terminal GSM864Q V3 00 Terminus GPS Terminal HV GSM864Q V4 00 Terminus Non GPS Terminal HV GSM864QP V1 00 Terminus GPS Terminal w Python GSM864QP V2 00 Terminus Non GPS Terminal w Python GSM864QP V3 00 Terminus GPS Terminal HV w Python GSM864QP V4 00 Terminus Non GPS Terminal HV w Python Note disclaimer The Python enabled terminals are not PTCRB or carrier certified 7 5 Revision History Revision Revision Date Note V 1 0 04 18 07 Preliminary Manual V 2 0 06 26 07 Added Mechanical Drawings V 3 0 06 28 07 Added Order Information amp Spec Corrections V 4 0 08 23 07 Updated Mechanical Drawings V 5 0 10 23 07 Update Content and Additions RO6 02 18 08 Updated Block Diagram and Revision Control R07 04 11 08 Pin Out Correction R08 07 23 07 Approvals Abbreaviations Revisions Terminus Hardware user Guide GSM864Q Page 21 Rev 08 Date 07 23 08 JANUS ee more Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice C MMUNICATI NS Terminus GSM864Q Hardware User Manual Janus Remote Communications Division of The Connor Winfield Corporation 2111 Comprehensive Drive Aurora Illinois 60505 630 499 2121 Fax 630 851 5040 www janus rc com
23. sdadiabadieduxtensiiabsshersiansl 10 12 4 4 1 Description 4 4 2 Pin out 4 4 3 Signal Description 4 4 4 Signal Detail 4 4 4 1 General Purpose Input Output 4 4 4 2 Analog to Digital Converter 4 4 4 3 Terminus Control 4 4 4 3 1 Reset Pin 4 4 4 4 ON OFF Pin 4 4 4 5 PWRMON Pin 4 4 4 6 UART_SEL Pin 4 4 5 Terminus Control JANUS Terminus Hardware user Guide GSM864Q Page2 Rev 08 Date 07 23 08 REMOTE C MMUNICATIONS Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice 4 INTERFACES COMUMUCG v saaa Ea ES A AEN EEA EE A EA 7 14 4 5 LED Status Indicators 4 5 1 Description 4 5 2 GSM 4 5 3 GPS AO RF terna osoen a E E EEE E 13 14 4 6 1 Description 4 6 2 GSM Antenna 4 6 2 1 GSM Antenna Interface 4 6 2 2 GSM Antenna Specifications 4 6 2 3 GSM Antenna Installation Guidelines 4 6 3 GPS Antenna 4 6 3 1 GPS Antenna Interface 4 6 3 2 GPS Active Antenna Specifications 4 6 3 3 GPS Antenna Installation Guidelines T SIM Card IPSCO cetseecactorte occa gexeehemdnciee otnnace E Ea a aA AE OEA 14 4 7 1 Description 4 7 2 Additional details 5 TECHNICAL SPECIFICATIONS bussina O aaa a 15 17 5 1 Electrical Specifications sccscvacccsackonsiesesanaondice vanes antlnctiocnsasdaectaadalshexataasestavilacenseianssanusadonsinenennedstaceiie 15 16 5 1 1 GSM Module Specifications 5 1 2 GPS Module Specifications 5 1 3 I O Level Specifications 5 2 GC864Q Mechanical DIMENSIONS sciciicccncdadscnssvudde
24. t of Connor Winfield is strictly prohibited Connor Winfield makes every effort to ensure the quality of the information it makes available Notwithstanding the foregoing Connor Winfield does not make any warranty as to the information contained herein and does not accept any liability for any injury loss or damage of any kind incurred by use of or reliance upon the information Connor Winfield disclaims any and all responsibility for the application of the devices characterized in this document and notes that the application of the device must comply with the safety standards of the applicable country and where applicable with the relevant wiring rules Connor Winfield reserves the right to make modifications additions and deletions to this document due to typographical errors inaccurate information or improvements to programs and or equipment at any time and without notice Such changes will nevertheless be incorporated into new editions of this application note All rights reserved 2007 Connor Winfield Corporation Terminus Hardware user Guide GSM864Q Page3 Rev 08 Date 07 23 08 J AN U S REMOTE Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice C MMUNICATIO NS 2 REFERENCES 2 1 Telit Document List Please refer to Telit s website at www telit com for the latest information on the GC864 GSM module 2 1 1 1vv0300733 GC864 Hardware User Guide 2 1 2 1vv0300740 GC864 Softwa
25. twork If response is different than this please refer to the Telit AT Command Reference document for more information 6 3 3 Check signal quality Enter AT CSQ lt cr gt And wait for response CSQ lt rssi gt lt ber gt JANUS Terminus Hardware user Guide GSM864Q Page 18 Rev 08 Date 07 23 08 REMOTE C eMMUNICATIONS Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice 6 OPERATION continued 6 4 Making a Voice Call 6 4 1 Voice call mode allows you to use a telephone handset to communicate with a properly equipped subscriber unit e To set the call mode to voice enter AT FCLASS 8 lt cr gt and wait for response OK e To set the audio path of the Terminus to internal for handset use enter ATHCAP 2 e To dial the phone number enter ATD lt 8885551234 gt lt cr gt e To disconnect the call enter ATH lt cr gt 6 5 Making an SMS Call 6 5 1 SMS Select Message Service mode allows you to send a text message max 160 characters to a SMS capable subscriber unit e To set the message mode to text enter AT CMGF 1 lt cr gt e To enter the receiving subscriber unit phone number and message enter 1 AT CMGS lt 8885551234 gt 2 Wait for response gt then enter message text 3 Enter ctrl z lt cr gt to end message 6 6 Making a GPRS Data call 6 6 1 GPRS is a data service that uses Packet Data Protocol PDP e To set up the PDP context parameters enter AT C
26. unctionally divided up into the following groups General Purpose I O interface the ADC interface Terminus Control interface and GPS Receiver interface The pin designations and specifications for this interface are shown below 4 4 2 Pin Out Bottom View Pai PABRBRBRBRRBRRBRRRABBRBRS a Pin 50 Pin 2 4 4 3 Signal Description Pin Description I O Signal Type Note 1 3 165 Vdc Output refer to Supply Specification OUTPUT N A 3 RESET INPUT Internal Pull up 5 ON OFF INPUT Internal Pull up 1 7 PWRMON OUTPUT 2 8V_CMOS 9 UART_SEL INPUT 2 8V_CMOS 11 ADC1 INPUT ANALOG 13 GPIO1 BI DIR 2 8V_ CMOS 15 GPIO2 BI DIR 2 8V_CMOS 17 GPIO3 BI DIR 2 8V_CMOS 19 GPIO4 BI DIR 2 8V_CMOS 21 GPIOS BI DIR 2 8V_CMOS 23 GPIO6 BI DIR 2 8V_CMOS 25 GPIO7 BI DIR 2 8V_CMOS 27 GPIO8 BI DIR 2 8V_CMOS 29 GPIO9 BI DIR 2 8V_CMOS 31 DCE Ready DSR OUTPUT 2 8V_CMOS 33 Clear to Send CTS OUTPUT 2 8V_CMOS Terminus Hardware user Guide GSM864Q Page10 Rev 08 Date 07 23 08 JANUS zt more C eMMUNICATIONS Copyright 2008 Janus Remote Communications All Rights Reserved Specifications subject to change without notice 4 Interfaces continued 4 4 3 Signal Description continued Pin Description I O Signal Type Note 35 Ring Indicator RI OUTPUT 2 8V_CMOS 37 Carrier Detect CD OUTPUT 2 8V_CMOS 39 DTE Ready DTR INPUT 2 8V_CMOS 41 Request to Send RTS INPUT 2 8V_CMOS 43 GPS_Rx
Download Pdf Manuals
Related Search