Quick Start Guide 9145 NID
Contents
1. N 6943300 Rev A Page 1 of 8 Figure 2 Optical module insertion in the EXT port Step 3 Rackmount Installation To mount the 9145 in a rack carefully remove the four rubber feet located under the NID using a small flat screwdriver Install the rack mount ears using the screws provided in the kit onto the 9145 chassis Screw in three on each side of the NID using a Phillip s head screw driver as shown in Figure 3 Figure 3 Rackmount ear installed When mounting the unit in a rack be sure to accommodate at least IRU 1 75 of space in the rack due to the height of the NID See Figure 4 Figure 4 9145 installed in a rack Canoga Perkins Corporation 20600 Prairie Street Chatsworth CA 91311 6008 Phone 818 718 6300 FAX 818 718 6312 www canoga com P N 6943300 Rev A Page 2 of 8 Step 4 Applying Power For AC powered NIDs power up the device by inserting the provided power cord to an AC outlet During the boot up stage which may take up to 20 seconds the LEDs will turn amber and the STA LED will flash until the boot up process is complete For DC powered NIDs if a 48VDC power source is used connect the grounding strap between the Chassis Ground and the VDC terminals If connecting to a 48VDC source to the NID connect the grounding strap between the Chassis Ground and the VDC terminals With power now applied the unit will initiate the boot up process All LEDs in the front will flash amber and the STA LED wi2. 600 Prairie Street Chatsworth CA 91311 6008 Phone 818 718 6300 FAX 818 718 6312 www canoga com P N 6943300 Rev A Page 3 of 8 Assign an icon and a name for the session gt New Connection HyperTerminal d j l0 x File Edit Yiew Call Transfer Help ols 6 3 ala i wy New Connection Enter a name and choose an icon for the connection Name 3145 NIDI Cancel N ie Disconnected Auto detect Auto detect SCROLL CAPS NUM Capture Print echo Figure 7 Connection Properties After a name and icon is assigned the COM port properties menu will appear Configure the connection settings to the values listed Bits per second 9600bps Data bits 8 Parity None Stop bits 1 Flow control None If the HyperTerminal screen is scrolling up make sure that Terminal Emulation in the Properties menu is set to VT100 If the screen shows random symbols instead of letters verify that the terminal speed is set to 9600bps Step 6 Logging In In the log in screen type the default Username admin and Password admin to access the user interface The MAIN MENU will appear and will allow you to make necessary configuration changes based on your selection Refer to the user manual for more detailed information Canoga Perkins Corporation 20600 Prairie Street Chatsworth CA 91311 6008 Phone 818 718 6300 FAX 818 718 6312 www canoga com P N 6943300 Rev A Page 4 of 8 Canoga Perk
3. F76 01 24 34 FUNCTIONAL CONFIGURATION Local Remote Offline User Port Speed Duplex Link Down Ext Port Speed Duplex Link Down 1 User Port Setting 2 Ext Port Setting Autonegotiate 3 RMTF Disabled 4 Link Loss Fwd Disabled 5 Flow Control Disabled 6 PVST BPDU Filtering Disabled 7 Sideband Management Disabled Hit SPACE toggle selection ENTER accept ESC cancel Figure 10 Functional Configuration screen Module Type Settings 10 100 1000 UTP Autonegotiate Disable 10M Half Duplex 10M Full Duplex 100M Half Duplex 100M Full Duplex 1000M Half Duplex 1000M Full Duplex 10Mbps Optical Disable 10M Half Duplex 10M Full Duplex 100Mbps Optical Disable 100M Half Duplex 100M Full Duplex 1000Mbps Optical Autonegotiate Disable 1000M Half Duplex 1000M Full Duplex Table 1 Module type and settings Canoga Perkins Corporation 20600 Prairie Street Chatsworth CA 91311 6008 Phone 818 718 6300 FAX 818 718 6312 www canoga com P N 6943300 Rev A Page 6 of 8 Step 7 Cable Connection Once the desired changes are made to the modules the UTP or fiber optic cables can be installed A Category 5 UTP cable can now be installed from the 10 100 1000Mbps UTP module to your switch Canoga Perkins recommends at Category 5e UTP cable or better for 1000BaseT installations Remember that the USR port is the port connected to your local client device and the EXT port
4. ION Local Remote Offline MAC Address 00 40 2A 00 9B 80 Management Port DOWN 1 Ethernet IP Address 000 000 000 000 Subnet Mask 255 255 255 000 Default Gateway 000 000 000 000 2 Inband Management Port Both Ports 3 Management VLAN Tagging Disabled 4 Management VLAN Number 1 5 SLIP PPP IP Address 000 000 000 000 6 Serial Port Config VT100 7 BOOTP Disabled 8 Telnet Security Disabled 9 Host Table 10 Trap Table Select 1 10 1 Figure 13 IP SNMP Agent Configuration screen This concludes the initial set up of the 9145 NID For detailed information on other functions of the 9145 NID consult the user manual or contact Canoga Perkins Tech Support line at 818 718 6300 Canoga Perkins Corporation 20600 Prairie Street Chatsworth CA 91311 6008 Phone 818 718 6300 FAX 818 718 6312 www canoga com P N 6943300 Rev A Page 8 of 8
5. Quick Start Guide 9145 NID Overview This document provides instructions for installation and initial configuration of the Canoga Perkins model 9145 NID Network Interface Device Parts List 1 x 9145 4 AC power or 9145 5 DC power 1 x User USR port interface module typically a UTP module but can also be an optical module 1 x Extension EXT port interface module typically an optical module 1 x Set of 19 or 23 optional rack mount ears 1 x AC power cord Tools Required 1 x EIA 232 DB 9 cable not included 1 x Phillips flat screwdriver if mounting in a relay rack step 1 Unpacking Unpack the 9145 and check the unit for damage Ifthe unit is damaged contact Canoga Perkins Tech Support line 800 360 6642 and ask for an RMA step 2 Module Insertion It is very likely that the USR and EXT ports are already occupied by the correct interfaces for the application from the factory However if the interfaces are ordered separately follow the next steps to configure the modules Insert the user interface module in the USR port slot of the NID The module should slide into the slot with ease and make contact with the rear connector without excessive force Tighten the thumbscrew and do the same for the EXT port Figure 1 10 100 1000Base T UTP module insertion in USR port Canoga Perkins Corporation 20600 Prairie Street Chatsworth CA 91311 6008 Phone 818 718 6300 FAX 818 718 6312 www canoga com P
6. ins Corp Ethernet Network Interface Device 06 Jan 1970 Model 9145 4 V03 40 F76 04 11 30 Please Enter Login Username admin Please Enter Login Password Figure 8 Log In screen Canoga Perkins Corp Ethernet Network Interface Device 06 Jan 1970 Model 9145 4 V03 40 F76 04 11 40 1 System Configuration 2 Diagnostics 3 Link Status 4 System Alarms 5 Layer 2 Statistics 6 RMON Group 1 Statistics 7 System Log 8 Utilities 9 Software Upgrade 10 Manage Logged In Users 11 Logout Select 1 11 Figure 9 Main Menu screen Step 7 Module Configuration From the Main Menu type 1 enter then 2 enter to access the Functional Configuration screen The Functional Configuration screen will allow you to change the settings of the USR and EXT port modules and Table 1 lists the modules available for the NID and their respective settings Verify the link speed and duplex of the local and remote device and change the settings of the modules accordingly To change the settings type the number of the setting you wish to change and use the space bar to toggle through the selections Use the ESC key to cancel your selection or to return to the earlier screen Canoga Perkins Corporation 20600 Prairie Street Chatsworth CA 91311 6008 Phone 818 718 6300 FAX 818 718 6312 www canoga com P N 6943300 Rev A Page 5 of 8 Canoga Perkins Corp Ethernet Network Interface Device 07 Jan 1970 Model 9145 4 V03 40
7. is the port facing the network trunk Connect the fiber to the optical module T PERKINS K O Oo Tx iQ Rx From Tx of Remote Device To Rx of Remote Device Figure 11 Fiber optic cable connection step 8 IP Address Subnet Mask Default Gateway Set u From the System Configuration menu type 5 then enter to access the IP VLAN Configuration screen Canoga Perkins Corp Ethernet Network Interface Device 07 Jan 1970 Model 9145 4 V03 40 F76 01 24 34 1 Hardware Information 2 Functional Configuration 3 VLAN Configuration 4 VLAN P Bit Translation Tables 5 IP SNMP Agent Configuration 6 Trap Configuration 7 Security Configuration 8 Account Configuration 9 System Info Configuration Select 1 9 5 Figure 12 System Configuration screen To configure the IP address select 5 press enter and type the IP address you wish to assign to the unit Press enter to accept the changes The Subnet Mask and Default Gateway must be entered at this point as well and note that the Subnet Mask and Default Gateway must be in the same class as the IP address i e Class A Class B or Class C Canoga Perkins Corporation 20600 Prairie Street Chatsworth CA 91311 6008 Phone 818 718 6300 FAX 818 718 6312 www canoga com P N 6943300 Rev A Page 7 of 8 Canoga Perkins Corp Ethernet Network Interface Device 07 Jan 1970 Model 9145 4 V03 40 F76 01 24 34 IP SNMP AGENT CONFIGURAT
8. ll flash until the boot up process is complete a Figure 5 DC power entry in the rear of the NID Step 5 Management Access To access the user interface of the NID a VT100 session must be created through HyperTerminal or a comparable VT100 terminal Connect a DB 9 EJA 232 straight cable from your PC or laptop COM lor any open COM port to the EIA 232 port of the NID Access HyperTerminal session from your laptop or terminal through the Programs Accessories Communications Hyperterminal menu ai Burn CD amp DYDs with Roxio At g i New Office Document H a ocument VER Query a Open Office Document C7 Set Program Access and Defaults LA w H xCe Wor cae Windows Catalog Excel ard up gt nternet login txt pions t Windows Update g Winzip DeBerry E fam System Tools F a Programs z Canogaview Smart Element Manager Standalone m Ea HyperTerminal Eg Documents H IT ROT Personal workstation Network Connections ee S F a a In Spybot Search amp Destroy 9 Network Setup Wizard Settings o in TFTF Server New Connection Wizard ny ye Search m Trend Micro OfficeScan Client a Remote Desktop Connection s Ee ScreenPrint Gold 2 5 Wireless Network Setup wizard 2 Help and Support f HyperTerminal x J Run i SS Undock Computer Shut Down arteak F igure 6 Accessing HyperTerminal Canoga Perkins Corporation 20
Download Pdf Manuals
Related Search