automatic drum washing machine user manual hw
Contents
1. W NN AN SAFETY INSTRUCTIONS BEFORE SWITCHING THE APPLIANCE ON FOR THE FIRST TIME 0 Use a separate earthed socket for the power supply Make sure that the plug is accessible Hold the plug and not the electric cable when unplugging the power supply Make sure that the fuses in the power circuit are rated for 15A components from aging Make sure that the power cord is not caught under or in the appliance and avoid damage to the power cable Check that hose joints and connections are firm and water can leak If joints are loose or there is leakage turn off the water supply and repair Do not use the washing machine until the hoses are properly fixed DURING DAILY USE OF THE APPLIANCE 0 up zips and fix loose threads to prevent the items from being entangled If necessary put small items into a net bag or pillow off the machine after each wash program and switch it off at the mains to save electricity and for safety Wipe clean the lower part of the porthole Keep the door slightly open when the washing machine is not in use to prevent formation of odours Let the power cord be replaced by the manufacturer his service agent or offer accordingly qualified persons in case itis damaged Ensure that the appliance is not used by persons with reduced physical sensory or mental capabilities lack of experience and k2. Speed button D Start pause button E Intense button F Rinse hold button Rinse hold button Detergent distribution drawer G Extra rinse button L Speedup button H High wash M Power button Delay button J Display _ Select program by turning the knob See program modes on page 8 _ Select the desired washing temperature 30 40 50 60 90 C by pressing and holding down this button When selected the temperature is shown on the display Cold wash is selected when the symbol is displayed _ Select the desired spin speed 0 400 600 800 1000 1200 1400 rpm by pressing and holding down this button When selected the speed value is shown on the display The washing machine does not spin when 0 is displayed The washing machine spins at 1200 rpm when 1200 is displayed _ f you press this button will be displayed and operation will start If you press this button during a wash cycle the sign will start blinking and operation will pause Press it again resume operation Note After operation is suspended the washing temperature spinning speed and other functions can not be reset _ Press this button for 2 seconds to unlock the door if the status allows the door to open water level lower than porthole water temperature lower than 50 C stopped motor _ If the laundry is heavily soiled press this button before starting the program When the button is pressed the
3. to 40 C to 40 C to 40 C 0 1090 C 0 to 40 C 0 10 40 C No Preset 4 40 C 40 C 30 40 C 40 C 40 C 30 C 30 C Optional w 1 Detergent compartment for prewash mode f 2 Detergent compartment 3 Compartment for softener and other additives Recommended 3 1 L V L Fost colus Medium soled I L L Cotton or synthetic V Different material ABBA Spots wear M Lg pug AWA AA A MAX LOAD 8 kg 8 kg 4 kg 3kg 4 kg 4 kg Akg 4 kg 8 kg 8kg 8kg Preset spin speed 1000 pm 1000 rpm 1000 pm 600 rpm 1000 pm 1000 rpm 1000 pm 800 rpm 400 rpm 400 rpm 1000 pm CONSUMPTION AND TECHNICAL DATA CONSUMPTION TABLE The wash cycle times are intended as a guide only The actual time used may vary due to different water pressure initial water temperature eic PROGRAM Prewash Cotton 60 C Synthetics Wool Comfort 40 Mixed Jeans Sport Hand wash LOAD 8 4kg jk 4kg Akg 4 kg 4 kg 4 kg ENERGY CONSUMPTION 0 663 kWh 1 326 kWh 0 481 kWh 0 197 kWh 0 466 kWh 0 527 kWh 0 527 kWh 0 179 kWh 0 147 kWh EN 60456 test program Energy label program with Intense and 1400 rpm spin speed TECHNICAL DATA Power source Max working current A Water pressure MPa Nominal load kg
4. Spinning speed r min Washing programs Max power W Dimensions HxDxW mm Net weight kg HW F 1481 ME 220 240 V 50 Hz 10 0 03 lt P 6 1400 1 2000 850 x 650 x 505 86 HW 1281 ME 220 240 V 50 10 0 03 P 6 1200 1 2000 850 x 650 x 595 86 WATER CONSUMPTION 1051 6261 1361 19 61 1361 5131 10 21 37 4L 4181 HW F 1081 ME 220 240 V 50 hz 10 0 03 lt P 6 1000 1 2000 850 x 650 505 86 WASHING TIME 2151 2 55 h 1 16 h 104 h 0 44 h 1 24 h 148 h 0 28 h 0 57 h HW 881 ME 220 240 V 50 Hz 10 0 03 P 6 800 1 2000 850 x 050 505 86 WASHING METHODS PLEASE NOTE This washing machine is for domestic use only Do not use it for purposes other than that for which it was designed Follow the instructions given on the label of each garment and wash only machine washable garments POWER SUPPLY Connect the washing machine to the power supply 220V to 240V 50hz WATER CONNECTION Turn on the tap The water must be clean and clear Note Before use check for leakage in the joints between the tap and the inlet hose by turning on the tap PREPARING THE LAUNDRY Sort out clothes according to fabric cotton synthetics wool or silk and to how dirty they are Separate white clothes from coloured ones Wash them first by hand to check if they fade or run Empty pockets keys coins etc and remove the harder decorativ
5. the hose back 4 Remove the filter by turning counterclockwise 5 Flush the filter clean with running water 6 Replace the filter by turning clockwise and remount the cover Caution The filter must be in place or it may lead to leakage WATER INLET AND INLET FILTER To prevent blockage to the water supply by ingress of foreign substances clean the water inlet and inlet filter regularly MOVING THE MACHINE If the machine is to be moved to a distant location replace the transportation locks removed before installation to prevent damage as shown below 1 Remove the blanking plugs 2 Remove the back cover J Insert the synthetic stabilisers and the transportation bolts 4 Tighten the bolts with a spanner 5 Replace the back cover LONG PERIODS OF DISUSE If the washing machine is left idle for a long period pull out the electrical plug and turn off the water supply Open the washer door to prevent formation of moisture and odours Let the door open while not used DISPLAY CODES DISPLAY CODES AND SPECIAL FUNCTIONS CODES CAUSES SOLUTIONS Er Washer door is not properly shut _ lose the washer door properly Drainage error _ Clean the filter and check the drain hose for blockage Temperature sensor error _ Please contact the Service Center Appears at the end of a cycle Ed Heat
6. AUTOMATIC DRUM WASHING MACHINE HW F148 HW F 128 HW F108 HW T88 USER MANUAL 148 ME I H ME HW FIO8 ME ME O o X U SJ V4 O Cine Y ZZ e 2 BEFORE USE 03 04 gt INSTRUCTIONS 05 INSTALLATION u u u u u u uu uuu 06 u u u 08 LEGEND v Yes Hz No Optional USING THE APPLIANCE gt SCONSUMPTION AND TECHNICAL DNA gt WASHING METHODS MAINTENANCE SCLEANING amp 0 SUS UE 18 P TROUBIESHOOTING n For your safety any instructions in this manual with this Warning sign must be followed strictly DISPOSAL Do not dispose of electrical appliances as unsorted municipal waste use separate collection facilities Contact your local government for information regarding the collection systems available If electrical appliance for disposals at least free of charge appliances are disposed of in landfills or dumps hazardous substances can leak into the groundwater and get into the food chain damaging your health and well being When replacing old appliances with new ones the retailer is legally obligated to take back your old SS COMPONENTS THANKS FOR PURCHASING A HAIER PRODUCT Please read these instructions car
7. cannot be kept in INSTALLATION ADJUSTING THE BOTTOM COVER e Before removing the transportation bolts please fix the bottom cover to the bottom of the washing machine Lay down the machine fig 1 screw off the feet and adjust the bottom cover with the four holes corresponding the screw holes of the feet Then screw the feet back on 4 through the cover and fix it thus securely to the bottom of the machine fig 2 It keeps out the dampness and reduces the noise DISMANTLE THE TRANSPORTATION BOLTS The transportation bolts are designed for damping anti vibration components inside of the washing machine during the transportation process 1 Remove the back cover 2 Remove the three bolts on the rear side and take out the synthetic stabilisers from within the machine 3 Replace the back cover 4 Fill the holes left by the bolts with blanking plugs Note Keep the transportation bolts and synthetic stabilisers in a safe place for later use ADJUSTING THE WASHING MACHINE There are adjustable feet under the bottom of the washing machine Before use they should be adjusted so that the machine is level This will minimise vibrations and thus noise during use It will also reduce wear and tear We recommend using a spirit level to level the appliance INLET HOSE 1 Connect the nut on the inlet hose to the connector on the water valve 2 Ap
8. d Water supply failure The program knob is not properly set The washer door is not properly closed The inlet hose filter is blocked The height of the drain hose is below 80 cm The drain hose is in water Drain hose is blocked Drain hose end is higher than 100 cm above the floor level filer is blocked Not all transportation bolts have been removed Washing machine is located on an uneven surface or is not level Machine load is over 8 kg Water or electricity failure Washing machine is in soaking cycle Washing machine is in anti crease soaking cycle Washing machine gives an error message The detergent is not a low foaming type or for manual wash Excessive use of detergent The washing program duration will be adjusted according to the laundry load and the initial water temperature SOLUTIONS _ Check connection to the power supply _ Check the power supply _ Close the washer door properly _ sure the machine is switched on _ Make sure to select a program _ Tum on the water tap _ Check water pressure _ Check the inlet hose _ Ensure the water supply _ Set the program knob properly _ Close the washer door properly _ Unblock the inlet hose filter Install drain hose within 80 100 cm of height _ Make sure the drain hose is not in water _ Unblock the drain hose _ Make sure the drain hose end is lower than 100 cm above floor level _ Unbloc
9. e delay time must be longer than the program length selected This function can not be selected in the Rinse Spin and Drain program _ The display shows the washing time remaining the selected temperature and speed the options the alarm warning etc see Display codes on page 12 _ Instructions are printed on the handle of the drawer Open the drawer three compartments can be seen Compartment 1 Pre wash detergent Compartment 2 Detergent for programs 1 to 9 Compartment 3 Softener conditioning agent perfume and other additives _ By pressing the Delay and Start Pause buttons for 3 seconds after having started a program the button lock is activated The display shows In order to cancel the button lock press the two buttons again for 3 seconds and the display will disappear Caution the button lock needs to be cancelled actively it will not disappear automatically after the washing cycle _ Press this button before starting the program to reduce the washing time and temperature The speed up light will is on until the program ends _ Press this button to turn the machine on and off It will turn off automatically after five minutes without activity PROGRAM SELECTION PROGRAM MODES Program 1 Prewash 2 j Synthetics 1 Wool 5 Comfort 40 6 ale Jeans 0 9 Bond wash 10 ai 12 Drain v es Temperature Maximum t090 C t0 90 C 0 to 00 C 0
10. e objects e g brooches Garments without hems underwear finely woven textile such as fine curtains are to be put into wash bag it is better not to wash them in a washing machine lose zippers and hooks make sure the buttons are sewn on tightly and place small items such as socks belts bras etc in the wash bag Unfold large pieces of fabric such as bed sheets bedspreads etc Turn shirts inside out LOADING THE MACHINE Open the washer door put in the laundry piece by piece Close the door tightly When first using the washing machine let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing machine Do not overload the washing machine SELECTING DETERGENT The washing efficiency and the performance is determined by the quality of detergent used Special non foaming detergent produces good washing results Use specific detergents for synthetic and woollen goods Do not use dry cleaning agents such as trichloroethylene and similar products Note Do not add more detergent than needed Please follow the dosage recommendation on the detergent package ADDING DETERGENT Slide out the detergent drawer and put the required detergent and softening agent into the corresponding compartments Push back the drawer gently Refer to the instructions on the drawer Caution For prewashing program detergent should be added to both compar
11. efully before using this appliance The instructions contain important information which will help you get the best out of the appliance and ensure sate and proper installation use and maintenance Keep this manual in a convenient place so you can always refer to it for the safe and proper use of the appliance If you sell the appliance give it away or leave it behind when you move house make sure you also pass on this manual so that the new owner can become familiar with the appliance and safety warnings ACCESSORIES Check the accessories and literature 1 Bottom cover 1 Inlet hose assembly lx User manual 1 Drain hose bracket 1x Warranty card optional 3x Blanking plugs PREPARATION PREPARING THE MACHINE Remove all the packing materials to prevent unsteadiness including the polystyrene base Upon opening the package water drops may be seen on the plastic bag and the porthole This is normal phenomenon resulting from water tests in the factory DESCRIPTION This diagram may be slightly different from the layout of the washing machine you have just purchased due to technical improvements Power switch Drain hose Door handle Water inlet valve Work Top Power cord Washer door Back cover Control Panel Back cover screws Detergent distribution drawer Transportation bolts Bottom trim v NM Peer e PTT RR TA
12. er error Appears at the end of a cycle _ Please contact the Service Center Err Water inlet error _ Check the tap and the water pressure Err Motor error _ Please contact the Service Center Er Motor error _ Please contact the Service Center End Water exceeds protective level _ Please contact the Service Center RIO Water sensor error _ Please contact the Service Center unb Laundry is unevenly distributed _ Recistribute laundry to balance the drum End End of wash cycle 1 16 Status information remaining program time is 1 hour and 16 minutes 0 01 Status information remaining program time is minute 60 Status information Preset washing temperature is 60 Cold wash 800 Status information Preset spinning speed is 800rpm Keyboard is locked Control panel lock function Press the Delay and the Start Pause buttons simultaneously for 3 seconds after starting a program It con no longer be changed by operating buttons or knobs The washing machine emits an audible signal while the control panel is locked To unlock press the Delay and Start Pause buttons again for 3 seconds Power off memory function In case of abrupt power failure or the need to cut off the power during a program cycle the present settings will be saved and the preset operation will resume when the power is on again This washing machine memorises the previous wash settings for each program If you press the Star
13. k the filter _ Remove all transportation bolts _ Make sure the washing machine is on an even surface and levelled _ Reduce amount of laundry in the drum _ Check the power supply _ Wait until the cycle is finished _ twill resume work affer some time _ Check display codes _ Check if your detergent is appropriate _ Reduce amount of detergent in the distribution drawer _ This is normal and doesn t affect the functionality Tel 39 0332 24511 Haier Europe Trading S r l a e f Via De Cristoforis 1 Fox 39 0332 245146 21100 Varese E mail het srl haiereurope com
14. nowledge without supervision or instruction by a person responsible for their safety Supervise children to ensure that they do not play with the appliance Keep away from heat sources and direct sun light to prevent plastic and rubber DO NOT ouch or use the appliance when barefoot or with wet or damp hands or feet Use flammable detergent or dry cleaning agent Use flammable sprays in close vicinity to the appliance Remove or insert the plug in the presence of flammable gas Alow children or infirm persons to play with the appliance or packing materials NNNNNN Install the appliance outdoors in damp place or in an area which may be prone to water leaks such as under or near a sink unit In the event of a water leak allow the machine to dry naturally Place the washing machine directly on a carpet or close to a wall or furniture DO NOT Touch the washer door during the washing process it gets hot Place heavy objects or sources of heat or damp on top of the appliance Hot wash foam rubber or sponge like materials Open the detergent distribution drawer during the wash cycle Force the washer door open The door is fitted with a selflock device and wil open shortly after the washing procedure is ended Open the washer door if the water level is visibly over the porthole Cover the washing machine with plastic cover so that inside dampness
15. off the water supply and unplug the power cord Open the washer door to prevent formation of moisture and odours Let the door open while not used TIPS FOR SAVING ENERGY 1 Collect clothes for one full wash load 2 Avoid overloading the washing machine 3 Prewash only heavily soiled clothes 4 Reduce the amount of detergent or choose the speed up wash programs for slightly soiled clothes 5 Choose a proper washing temperature Modern detergents can wash with very good result already in lower temperature than 60 C Only user higher temperature than 60 C for heavily soiled laundry 6 Follow the dosage recommendation on the detergent package to avoid using too much detergent 7 Softening agent makes clothes feel softer and easier to iron 8 Adding fabric conditioner will also get rid of static condensation to make ironing easier CARE CHART Resistant material COF Delicate fabric Washable at 95 C Washable at 60 C Washable at 40 C Washable at 30 C de Hand wash 59 Dry clean only Wool Seal LOAD REFERENCE Bed sheet single Blanket Blended fabric clothes Jackets Jeans Overalls Ladies Pyjamas Shirts Socks T Shirts Underwear eO i Bi x P gt Cotton Wool Cotton Cotton d l Blended fabrics Cotton Blended fabrics Bleachable in cold water Do not bleach at 200 C at 150 C at 100 C Don t iron Dry cleaning with any s
16. olvent Dry cleaning with pericloride Dry cleaning with aviation fuel ex Don t dry clean IN Hung to dry Dry on clothes hanger C Tumble dry reduced heat B Don t tumble dry Tumble dry normal heat Approximately 800g Approximately 3000g Approximately 800g Approximately 800g Approximately 800g Approximately 950g Approximately 200g Approximately 300g Approximately 50g Approximately 300g Approximately 70g CLEANING amp CARE AFTER WASHING Turn off the water supply and pull out electricity plug atter each wash Open the washer door to prevent formation of moisture and odours If the washing machine is left idle for a long period drain the water in the machine and replace the drain hose CLEANING THE DETERGENT DRAWER Clean the detergent distribution drawer regularly Swing out the drawer flush it clean with water and then replace it CLEANING THE MACHINE Unplug the machine during cleaning and maintenance Use a sott cloth dampened with soap liquid to clean the machine case and rubber components Do not use organic chemicals or corrosive solvents CLEANING THE FILTER Clean the filter once a month 1 Pull out the bottom cover with thin objects or tools carefully 2 Pull the drain hose out of the sewage set in the bottom panel 3 Hold the drain hose into a water container take out the plastic plug and let the excess water flow into the container Reinstall the plug and push
17. ply inlet hose to a water tab with cold fresh water Note Use the hose set supplied with the appliance Old hose sets should not be reused DRAIN HOSE 1 Use the drain hose bracket to keep the end of the drain hose retained and prevent the outflow of water Don t extend the length of the drain hose if an extended hose is required please consult a serviceman 2 The height of the drainage outlet must be 80 100 cm Fix the drain hose to the clip at the back of the washing machine to prevent it from dropping off Vote The drain hose should not be submerged in water and should be securely fixed and leak free If the drain hose is placed on the ground or if the pipe is at a height of less than 80cm the washing machine will continuously drain while being filled self siphoning CONNECTING TO THE POWER SUPPLY Before connecting to the power supply check The socket is adequate for the maximum power of the washing machine For safety fuses in the power circuit should be rated for no less than 154 The voltage should meet the requirement The power outlet should be capable of accepting the washing machine plug Connect the machine to an earthed socket outlet CONTROL PANEL Hater Program knob Temperature button Speed button Start pause button Intense button m C c5 wo OPERATIONAL FUNCTIONS A Program knob D lemperature button
18. t Pause button the previous settings are automaticaly selected To cancel a program or select a new program and options during the wash cycles a Press the Start Pause button then switch off the power and the program is automatically cancelled Turn the program selector again to choose another program b If you wish select an option during the wash cycle press the Stort Pause button then select the desired option and press the Start Pause button again Note The Rinse hold function can be selected directly without pressing first the Start Pause button but before the machine starts the spin program TROUBLESHOOTING TROUBLESHOOTING The following circumstances do not constitute problems Do not contact the Service Center until the problem has been confirmed PROBLEM Washing machine fails to operate Washing machine cannot be filled with water Machine is draining while being filled Drainage failure Strong vibration while spinning Operation stops before completing wash cycle Operation stops for a period of time Excessive foam in the drum which is spilled to the distribution drawer Automatic adjustment of the washing time CAUSES Poor connection to the power supply Power failure The washer door is not properly closed Machine has not been switched on There s no program selected Water tap is not tumed on Water pressure is less than 0 03 Mpa The inlet hose is kinke
19. tments 1 and 2 For other programs do not add detergent to compartment 1 Use liquid detergent according to the instructions on its package Do not use liquid detergent if the prewash mode or Start delay is selected Do not overuse softener otherwise it will damage the artificial fibers SELECTING PROGRAM To get the best washing results an appropriate washing program should be selected according to the laundry type There are instructions on the handle of the detergent distribution drawer Please turn the program knob clockwise to select the right program SELECTING FUNCTIONAL Select the required options Refer to the Control panel pages 08 and 09 SETTING WASHING TEMPERATURE Press and hold down the temperature button until the desired temperature is selected or the symbol for no water heating SETTING SPIN SPEED Press and hold down the speed button until the desired speed is selected or the symbol 0 is selected for no spin See Operational functions on the Control panel pages 08 and 09 for selecting temperature and spin speed It is advisable to select the recommended value WASHING Press the Start Pause button The washing machine will operate according to the pre set programs The washing machine will stop operation automatically when a washing cycle ends The End sign will appear on the display Open the washer door and take out the laundry AFTER WASHING Turn
20. washing time increases _ f you press this button the washing machine will not drain the water after the last rinsing operation but start a soaking cycle The indicator light goes on To spin the laundry press this button again The indicator light turns off and the program continues to the end Note Press only when Prewash Cotton Synthetics or Rinse is selected D Extra rinse button High wash Delay button Display Detergent distribution drawer Combined buttons for button lock Speed up button Power button _ Press this button the washing machine will perform additional rinses Press the button once to select one additional rinse The display will show P 1 Press the button repeatedly and the screen will display P 2 or 3 indicating two or three additional selected rinses The extra rinse light is activated and flashes during the performance P 1 2 3 is displayed alternating with the remaining time The light turns off and the display disappears when the extra rinse ends _ For heavily soiled laundry Press the button before starting the program to increase the amount of water used The high wash light is on during the performance _ Press the button repeatedly before starting the program to enter the time you want the machine to be finished in the start will delay from 0 5 to 24 hours in 30 minute intervals This also includes the length of the program itself so th
Download Pdf Manuals
Related Search