Firmware Release for Ex-Mashabrum
Contents
1. an incomplete Firmware update Press the ON OFF button while simultaneously holding down the 0 8 buttons and initialize 9030 FW NOTE 08 9083 may be required which will wipe all the network settings Use the USB Clone File backup that was performed from IMPORTANT NOTES to return all network settings Press the ON OFF button B Confirmation of the updated data After the update is complete check each data version in the Setting Mode 08 to confirm that the Firmware update was successful Not all data versions are displayed on List Print so please also confirm versions with table shown in the latter part of the bulletin C Adjustment Perform the adjustment of the equipment 1 2 Performing Image Quality Control 05 2742 Adjustment of Colour Registration Control 05 4719 Automatic gamma adjustment lt PPC gt 05 7869 using 4 FAX test pattern Automatic gamma adjustment lt PRT gt 05 8008 using 70 FAX test pattern BULLETIN 1141 Page 2 of 5 Functions added The following 08 codes have been added 08 Code Item Settings Details Sets the timing for when the toner 9 3 Sets the timing for when the toner near near empty message is displayed gt empty display The larger the value the later the 0 5 appears The larger the value the later display appears the display appears 0 Longer 1 1 Center normal 2 Shorter 2 3 No detection 4 S2. and private print 0 No limits 0 35 1 to 30 1 to 30 days gt 31 1 hour 0 53 32 2 hours 33 4 hours 9307 34 8 hours 35 12 hours 50 5 minutes 51 10 minutes 52 15 minutes 53 30 minutes Retaining of print data spool data 0 Disabled Default Print data can be retained or acquired 1 8761 when a problem occurs Enabled After acquiring the print data disable this function BULLETIN 1141 Page 3 of 5 8942 changing this setting Debug logs can Debug level settings 0 High debug level Debug information can be obtained by 1 Low debug level Default be acquired with USB script file debug_V01 sh 8628 is connected the Copy screen can be 1 Enabled Job operation when coin controller is 0 Disabled Default connected When Enabled and the coin controller switched to the Job Status screen during printing and a job can be performed Service notification when job is 0 Disabled Not sent 8641 cancelled l p 1 Enabled Sent This include E mail e Filing Internet Service notification is sent even at job Fax shared folders and USB cancellation Availability of the Job Build function 0 Disabled Default 8640 when a coin controller is enabled Enabled Only available when 08 9016 is set to 1 Fixes When a particular Docuworks document was transmitted in the PC FAX mode a PCL XL ERROR was sent The MFD would reboot intermittently in case
3. TOSHIBA EID TECHNICAL BULLETIN MODEL S DATE BULLETIN No SUBJECT e Studio 2040c 2540c 3040c 17 09 13 1141 System Firmware Version 3453 3540c 4540c Purpose e Release of e Studio 2040c 2540c 3040c and 3540c 4540c System Firmware Version 3453 Important Information e Print out NIC Configuration List and backup network settings via USB Clone from Control Panel in case of network initialization error This information is required if 08 9083 is initialized in step 6 of the update procedure e Different Firmware Versions for MFD 2040c 2540c 3040c and 3540c 4540c Please be aware that USB folder names are the same for both versions You can differentiate firmware versions by o 502DFWW 003 is F W for 2040c 2540c 3040c Low Spec o 502DFWW 103 is F W for 3540c 4540c High Spec e Refer to Bulletin 1032 CFP for RADF Serial Number compliance e Print out version list before beginning procedure i e 9 START gt 111 e After performing this firmware update please allow up to 10 minutes for the password screen e STUDIO Series to appear when entering 08 mode Do not power OFF The next time the MFD enters 08 mode it will take the normal amount of time Support Firmware is available from the Firmware Section of the Partner Area on the www eid toshiba com au site Drivers are available from the User Area on the www eid toshiba com au site For further information regarding drivers refer to Driver relea
4. e Private hold print were often used the MFD would lock up unless rebooted periodically e The MFD sometimes rebooted automatically during panel operation e Some TIFF files failed to print e Fax jobs failed when sending to an NEC Fax machine MED Firmware ITEM eS2040c 2540c 3040c eS3540c 4540c 08 Code HDD T140HD0W3453 T140HDOW3453 8952 OS T140SFOW3452 T140SFOW3452 9930 Engine ROM 140M 16 140M 16 9901 Scanner ROM 140S 07 140S 07 9902 GD1250 Fax F670 A11 F670 A11 9905 MR3021 RADF DF 0030 9903 MR3022 RADF DF 1030 9903 MJ1101 Finisher FIN 032 FIN 032 9904 Converter CNV 030 CNV 030 9945 MJ1106 Finisher FIN 014 FIN 014 9904 Saddle Stitcher SDL 014 SDL 014 9904 Converter CNV 030 CNV 030 9945 MJ1031 Hanging Finisher FIN 09 FIN 09 9904 MJ6103 Punch Unit PUN 031 PUN 031 9944 BULLETIN 1141 Page 5 of 5
5. etting with 3 5 Setting with the number of counts 3 5155 1 The period of time number of counts from the appearance of the near empty display to actually running out of toner is longer larger than that of center 2 The period of time number of counts from the appearance of the near empty display to actually running out of toner is shorter smaller than that of center 3 When the remaining toner or number of counts is lower than the one set in 08 5810 5811 the toner near empty display appears Fine adjustment of threshold for 83 default Adjusts the threshold value for displaying displaying remaining toner and toner remaining amount of toner and toner near 5156 near empty 50 150 empty Display threshold value default threshold value x setting value 100 unit Toner near empty status threshold 3 Default This code is used when the value of 08 value setting 5155 is set to 4 Use this code to specify 5810 1 99 the threshold value unit for displaying the toner near empty status The accuracy of value is influenced by usage environment or originals Toner near empty status threshold 1000 This code is used when the value of 08 value setting number of sheets Default 5155 is set to 5 Use this code to specify the threshold value unit number of 5811 1 9999 sheets for displaying the toner near empty status The accuracy of value is influenced by usage environment or originals Storage period of hold
6. f faxes sent using the PC Fax driver were blurred When the main power switch was turned OFF incorrect shutdown procedure incorrect total counter values were recorded in POWER ON_OFF log An error message sometimes appeared when a user logged on to the eCopy menu using the EWB function under an eCopy linked environment The specified page size was not stored within the FAX template Reports from Oracle were not printed correctly It took a long time to switch between the COPY and FAX menu If the fax number was entered quickly using the digital keys in the FAX menu a missed entry occurred as the result BULLETIN 1141 Page 4 of 5 e Some files printed incorrectly Missing text from USB e The thickness of the fine lines fluctuated when printing from MS Excel when page ratios were specified e If a fax was being scanned and the authenticated user logged out the fax job would fail e f a scheduled job Fax job to be re dialled or scheduled print job started when the MFD went into energy save mode the control panel would sometime lock e An incorrect fax number might be dialled in rare cases depending on the line connection e lf a job was paused and the MFD was turned off the job was not displated in Job Status e If a cover page was selected from Drawer 2 subsequent pages would also be drawn from Drawer 2 rather than Auto e Sometimes the MFD would reboot if multiple jobs were processed simultaneously e n an environment wher
7. s when the screen was switched to the FAX menu If an original was set on the ADF to be copied before a department code was entered only a single side was scanned even though the duplex or 2 sided was selected If the power of the MFD was turned ON after it had not been used for some time the FAX unit was not recognised When the preview function was used in the Scan or FAX mode an image of the previous job was displayed momentarily on the screen MFD authentication with an external server took longer with each subsequent authentication The LDAP authentication performance has been improved When data was uploaded or sent as a Fax job and contained characters other than 0 9 the operation would lock When printing from an AS400 environment some character positions were misaligned Printing of PCL5E data created in an AS400 environment sometimes failed Some logos and watermarks did not print correctly when printed from an AS400 The MFD would not start properly if the MFD was switched OFF using the main power The static IP address of the DNS server was overwritten by the dynamic IP address Printing a large amount of single page jobs consecutively could cause some print jobs to fail When an original was set on the ADF before a Department Code was entered Sort was not automatically selected Scan to FTP was not able to be performed to a folder of the FTP server whose upper level folder was not allowed scanning privilege The image quality o
8. se V1303 Contact your Toshiba EID Technical Support Specialist for further assistance MANDATORY PROCEDURE NO O INFORMATION ONLY PRODUCTION CHANGE FREE OF CHARGE PARTS CHANGE TIME REQUIRED 30Minutes TOSHIBA AUSTRALIA PTY LIMITED ACN 001 320 421 ABN 19 001 320 421 BULLETIN 1141 Page 1 of 5 Upgrade Procedure Refer to IMPORTANT INFORMATION before starting the firmware update A Updating System Firmware 1 7 Unzip the firmware file and store it with the following structure USB Root i soe 28400 502DFWW xxx Plt_integrity cfg Pubkey key Signatures sig T140HDOW xxxx tar T140MWW xx T140SYOWxxxx tar T140SLGWW xx Note 502DFWW 003 is RADF F W for 2040c 2540c 3040c Low Spec 502DFWW 103 is RADF F W for 3540c 4540c High Spec Boot MFD while holding down 4 9 When the Authentication screen appears Press OK as the password is blank by default Select items requiring updating and press START Don t turn the power off until the MFD beeps and Update successfully completed Restart MFD is displayed Following the successful completion of a USB Firmware upload the MFD must be turned off using the On Off button on the control panel not the main power switch As per the Firmware update procedure in the Service Manual Press the ON OFF button to shut down the MFD and then remove the USB media Failure to follow this instruction correctly may result in
Download Pdf Manuals
Related Search