Baby Monitor User Manual
Contents
1. ON position See the following diagram If you wish these two channels to be displayed at eight second intervals slide the 4 8 dip switch to the ON position or you can leave it in the OFF position and it will be displayed at four second intervals AIRES OFF orr IW HER When you want to stop the auto sequence function Slide the 4 B dip switch to the ON position to activate the CH 1 2 3 4 switch and slide all four channel dip switches to the OFF position Then slide the CH 1 2 3 4 switch to the same channel as the camera Monitor to A V function The Wireless Baby Monitor monitor unit has audio video outputs which can be used to transfer the picture and sound from the monitor screen to a TV screen Connect the outputs to the A V input on a TV set for a large screen display or connect the outputs to a VCR to record transmissions for later viewing 10 Wireless Baby Monitor User s Manual If you have any questions Symptoms Check Points No power is supplied a Is the power cord disconnected to the camera or Connect it monitor Camera Monitor is not turned on Slide the ON OFF switch to the ON position Wrong AC adapter used Use the AC adapter labelled OUTPUT 12V with the camera 15V with the monitor No sound or picture Channel switches are not on the same setting Set the camera and the monitor to same channel Signal interference due to microwave2. Your Wireless Baby Monitor If you wish to wall mount the camera it is recommended that the reception of the Video Monitor be tested before installing to the wall Have one adult hold the camera against the wall at the selected mounting area while another adult moves the monitor to varieties locations throughout the house to check reception If interference or other problems develop please refer to the section of this User s Guide titled If You Have Any Questions You may need to select a different location in the room for mounting the camera The following steps show you how to set up the Wireless Baby Monitor Make sure the camera and monitor are set to the same channel 1 2 3 or 4 Plug the jack on the 12V AC adapter cord into the AC adapter socket on the back of the camera Plug the AC adapter into a standard wall outlet Slide the ON OFF switch on the side of the camera to the ON position The power indicator should be lit Adjust the angle and focus of the camera lens for best view of baby Position the antenna so that it points to the monitor antenna Plug the jack on the 15V AC adapter cord into the AC adapter socket on the back of the monitor Plug the AC adapter into a standard wall outlet Turn the monitor on Adjust the volume control to a comfortable level Adjust the video image using the V Hold vertical hold Contrast and Brightness adjustment control on the side of the monitor Locate and orient the antenn
3. oven Turn off the oven or remove it from path between camera and monitor Signal interference due to other signal producing devices Change the channel setting on both the camera and the monitor Identify and eliminate the source of interference Relocate the camera and or monitor Out of range Relocate the camera and or monitor Improper antenna position Adjust camera monitor antenna orientation Wireless Baby Monitor User s Manual 11 Specifications Receiver Monitor Rx Description Video System NTSC Receiver Frequency 2 4 GHz 2 4835 GHz 2 4 GHz 2 4835 GHz Max Range clear line of 300 feet 750 feet sight Receiver Antenna Directional Directional inte Aca T Transmitter CMOS Camera Video System NTSC Transmitter Frequency 2 4 GHz 2 4835 GHz 2 4 GHz 2 4835 GHz Max Range clear line of 300 feet 750 feet sight 12 Wireless Baby Monitor User s Manual
4. Contents IMPORTANT SAFETY PRECAUTIONS BEFORE SETTING UP 1 WHAT YOU GET IN THIS PACKAGE nnmnnnnnnennnnnnne 2 GETTING TO KNOW YOUR WIRELESS BABY MONITOR 3 AMERICA nee 3 MONITOR derer ee isa nel tel Vent rites 5 SETTING UP YOUR WIRELESS BABY MONITOR 7 ORIENTING ANTENNAS FOR OPTIMAL PERFORMANCE su 8 WHAT ELSE CAN THE WIRELESS BABY MONITOR DO FOR YOU See 9 AUTO SEQUENCE FUNCTION sense 9 MONITOR TO A V FUNCTION sine 10 IF YOU HAVE ANY QUES TIONS nement 11 SPECIFICATIONS nm 12 Wireless Baby Monitor User s Manual i FCC Statement This equipment has been tested and found to comply with the limits for a Class B Digital Device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communication However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Con
5. as on both the camera and monitor according to the section of this User s Guide titled Orienting Antennas for Optimal Performance Wireless Baby Monitor User s Manual 7 Orienting Antennas for Optimal Performance The Wireless Baby Monitor broadcasts its high quality audio and video using directional antennas which must be oriented in a certain configurations for best results The 2 4 GHZ antennas have been designed to pivot and have limited rotation in either clockwise or counterclockwise directions Warning See instructions shown below for rotating antennas Rotating antennas beyond the specified range will result in permanent damage to both antennas and the mechanical stop Antenna does not rotate freely 360 degrees In most situations the flat pitted face of the antennas on both the camera and monitor should be facing one another Since all rooms are different for optimal reception additional slight pivots or rotations may be necessary If the camera and monitor are less than 10 feet apart keep the antennas flat in their casings 8 Wireless Baby Monitor User s Manual What else can the Wireless Baby Monitor do for you Auto sequence function With the Wireless Baby Monitor users can monitor a series of rooms for maximum supervision of the home or office The Wireless Baby Monitor can use up to four cameras on four different channels while the monitor can receive signals on up to four different channel and disp
6. even in a completely darkened room Note The video image displayed on the monitor may appear snowy when the camera is operating in darkness or very low levels of light Adjustable camera lens For focus adjustment LED indicator Lights up when the camera is ON Wireless Baby Monitor User s Manual 3 Rear View CHANNEL 1 2 3 4 Channel selection It is possible for the monitor to pick up sounds or display interference from other signal producing devices To minimize the potential for this problem four channels are available for use Make sure that the camera and monitor are set to the same channel ON OFF switch 12VDCIN 4 Wireless Baby Monitor User s Manual Front view Antenna See page 8 Orienting Antennas for Optimal Performance V HOLD CONTRAST BRIGHTNESS Volume Power control Wireless Baby Monitor User s Manual 5 Rear View 6 AUDIO OUTPUT See page 10 Monitor to A V function CH 1234 Channel selection It is possible for the monitor to pick up sounds or display interference from other signal producing devices To minimize this potential problem four channels are available for use Make sure that the camera and monitor are set to the same channel VIDEO OUTPUT See page 10 Monitor to A V function FUNCTION Auto sequence function switch See page 9 Auto sequence function DC 15V IN Wireless Baby Monitor User s Manual Setting Up
7. ges or modifications not approved by RF Link could void user s authority to operate the equipment Do remember that you are using public airwaves when you use the Wireless Baby Monitor and that sound and video may be broadcast to other 2 4 GHz receiving devices Conversations even from rooms near the camera may be broadcast To protect the privacy of your home always turn the camera off when not in use Wireless Baby Monitor User s Manual 1 What You Get in This Package The following items should be included in the box Please check that you have them all before installation A camera with built in transmitter A monitor with built in receiver A 12V AC adapter for camera only A 15V AC adapter for monitor only Warning Two AC adapters are included with the Wireless Baby Monitor The AC adapters can not be interchange Use the adapter labelled OUTPUT 12V DC with the camera Use the adapter labelled OUTPUT 15V DC with the monitor 2 Wireless Baby Monitor User s Manual Getting To Know Your Wireless Baby Monitor Camera Front View Antenna See page 8 Orienting Antennas for Optimal Performance Moveable base The camera can be mounted on the wall or it can be easily placed on a flat surface such as a table top dresser or shelf Note The bracket does not rotate freely 360 degrees Microphone For clear audio pick up Night vision LEDs The automatic night vision LEDs allow the camera to see your baby
8. lay them in sequence The Wireless Baby Monitor includes six dip switches for various operating modes as described in the following diagram BOAT S ES ON fe en ER Factory preset mode DIP 4 B The automatic channels sequence function ON Enables the CH 1 2 3 4 switch and stops the auto sequence function When stopping the auto sequence function slide all four channel dip switches to the OFF position Note If one or more of the four dip switches remains on the auto sequence function will continue on these channels even though the 4 B dip switch is in the OFF position OFF Disable the CH 1 2 3 4 switch and start the auto sequence function DIP 4 8 Sequence interval timer ON Displays at eight second intervals OFF Displays at four second intervals DIP 1 4 channel switch setting up the automatic channel sequence function Slide the channel dip switch that you wish to view to the ON position or slide the channel dip switch that you wish to deactivate to the OFF position Wireless Baby Monitor User s Manual 9 Example When you want to use the auto sequence function If you have two cameras and their channels are set on CH 1 and CH 3 and you wish to monitor the two different channels in sequence you must first slide the 4 B dip switch to the OFF position this means the CH 1 2 3 4 switch is now disabled Then slide the first and third dip switches to the
9. nect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help ii Wireless Baby Monitor User s Manual Important Safety Precautions Before Setting Up Congratulation on purchasing RF Link s 2 4 GHz Wireless Baby Monitor Before operating your Wireless Baby Monitor please read all these safety and operating instructions completely and then retain for future reference To prevent entanglement never place the camera in a crib or playpen Do not place the camera on any surface or mount it on any wall where the camera or its AC adapter cord are within reach of baby Keep the camera and monitor out of reach of children Never use the camera or monitor near water For example do not use near a bathtub washbowl laundry tub kitchen sink in a wet basement etc Disconnect the AC adapters from wall outlets during long periods of non use Position the camera monitor and AC adapters to allow adequate ventilation Keep the camera out of direct sunlight To prevent overheating keep the camera monitor and AC adapters away from heat sources such as radiators heat registers stoves or other appliances including amplifiers which produce heat Use only the AC adapters provided Use of any others may damage the camera and or monitor Plug into an electrical outlet with standard household power 120 volt AC outlet Chan
Download Pdf Manuals
Related Search